Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 680 views

    Specifications Vapor Barrier/Dampproofing (Ecodamp)

    Uploaded by

    Baugh Graphic Design
    The document provides specifications for applying a vapor barrier and dampproofing system to above-grade surfaces. It outlines requirements for surface preparation, materials, installation, and warranty. The vapor barrier material will be a spray-applied, fluid polymer-modified asphalt emulsion that dries to a nominal thickness of 20 mils. Installers must be certified by the manufacturer and follow all specifications for substrate treatment and application conditions.

    Copyright:

    © All Rights Reserved
    Download as DOC or read online from Scribd

    Specifications Vapor Barrier/Dampproofing (Ecodamp)

    Uploaded by

    Baugh Graphic Design
    680 views6 pages
    The document provides specifications for applying a vapor barrier and dampproofing system to above-grade surfaces. It outlines requirements for surface preparation, materials, installation, and warranty. The vapor barrier material will be a spray-applied, fluid polymer-modified asphalt emulsion that dries to a nominal thickness of 20 mils. Installers must be certified by the manufacturer and follow all specifications for substrate treatment and application conditions.

    Original Description:

    Original Title

    EDAGD

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides specifications for applying a vapor barrier and dampproofing system to above-grade surfaces. It outlines requirements for surface preparation, materials, installation, and warranty. The vapor barrier material will be a spray-applied, fluid polymer-modified asphalt emulsion that dries to a nominal thickness of 20 mils. Installers must be certified by the manufacturer and follow all specifications for substrate treatment and application conditions.

    Copyright:

    © All Rights Reserved
    Download as DOC or read online from Scribd
    Download as doc
    680 views6 pages

    Specifications Vapor Barrier/Dampproofing (Ecodamp)

    Uploaded by

    Baugh Graphic Design
    The document provides specifications for applying a vapor barrier and dampproofing system to above-grade surfaces. It outlines requirements for surface preparation, materials, installation, and warranty. The vapor barrier material will be a spray-applied, fluid polymer-modified asphalt emulsion that dries to a nominal thickness of 20 mils. Installers must be certified by the manufacturer and follow all specifications for substrate treatment and application conditions.

    Copyright:

    © All Rights Reserved
    Download as DOC or read online from Scribd
    Download as doc
    of 6

    SPECIFICATIONS

    VAPOR BARRIER/DAMPPROOFING (ECODAMP)

    SECTION 071000 – FLUID-APPLIED POLYMERIZED VAPOR BARRIER AND DAMPPROOFING


    (Above Grade)

    PART 1 – GENERAL

    1.1 RELATED DOCUMENTS

    A. Drawings and general provisions of the Contract, including General and Supplementary
    Conditions and Division 1 Specification Sections, apply to this Section.

    1.2 SUMMARY

    A. This Section includes the following:

    1. Surface preparation and substrate treatment.


    2. Vapor barrier and dampproofing membrane.
    3. Sheet flashing and accessories.

    B. Related Sections: The following Sections contain requirements that relate to this Section:

    1. Division 4 Section “Masonry” for concrete unit masonry placement, curing, and
    finishing.
    2. Division 4 Section “Masonry” for masonry restoration and cleaning.

    1.3 PERFORMANCE REQUIREMENTS

    A. General: Provide a vapor barrier and dampproofing system that prevents the passage of
    moisture in the absence of hydrostatic pressure and complies with physical requirements
    as demonstrated by testing performed by an independent testing agency of manufacturer’s
    current dampproofing formulations and system design.

    1.4 SUBMITTALS

    A. Submit Product Data for each type of vapor barrier/dampproofing specified, including
    manufacturer’s printed instructions for evaluating, preparing, and treating the substrate,
    technical data, and tested physical and performance properties.

    B. Project Data - Submit Shop Drawings showing locations and extent of vapor
    barrier/dampproofing, including details for substrate joints and cracks, sheet flashing,
    penetrations, and other termination conditions.

    C. Samples – Submit representative samples of the following for approval:


    1. Vapor barrier/dampproof membrane material.
    2. Geo-textiles and detailing sheet as required.
    3. Repair grouts.

    D. Installer Certificates – Submit certificates signed by manufacturer certifying that Installers


    comply with requirements under the “Quality Assurance” Article.

    1.5 QUALITY ASSURANCE

    A. Installer Qualifications: Engage an experienced Installer who is certified in writing and


    approved by vapor barrier/dampproofing manufacturer Epro Services, Inc. for the
    installation of ECODAMP material.

    B. Manufacturer Qualification: Obtain vapor barrier/dampproofing materials and system


    components from a single manufacturer Epro Services, Inc.

    C. Field Sample: Apply vapor barrier/dampproofing system field sample to 30 sq./ft. (2.8
    sq./m.) of deck or wall to demonstrate surface preparation, joint and crack treatment,
    thickness, texture, and standard of workmanship.

    1. Notify Architect one week in advance of the dates and times when field sample will be
    prepared.
    2. If Architect determines that field sample, does not meet requirements; reapply vapor
    barrier/dampproofing material until field sample is approved.
    3. Retain and maintain approved field sample during construction in an undisturbed
    condition as a standard for judging the completed vapor barrier/dampproofing material.
    An undamaged field sample may become part of the completed Work.

    D. Pre-installation Conference: A pre-installation conference shall be held prior to application


    of the vapor barrier/dampproofing system to assure proper substrate and installation
    conditions, to include contractor, applicator, architect/engineer and special inspector (if
    any).

    1.6 DELIVERY, STORAGE, AND HANDLING

    A. Deliver materials to Project site as specified by manufacturer labeled with manufacturer’s


    name, product brand name and type, date of manufacture, shelf life, and directions for
    storing and mixing with other components.

    B. Store materials as specified by the vapor barrier/dampproofing manufacturer in a clean,


    dry, protected location and within the temperature range required by vapor
    barrier/dampproofing manufacturer. Protect stored materials from direct sunlight.

    C. Remove and replace material that cannot be applied within its stated shelf life.
    1.7 PROJECT CONDITIONS

    A. Protect all adjacent areas not to be applied to. Where necessary, apply masking to
    prevent staining of surfaces to remain exposed wherever membrane abuts to other finish
    surfaces.

    B. Perform work only when existing and forecasted weather conditions are within
    manufacturer’s recommendations for the material and application method used.

    C. Minimum clearance of 24 inches is required for application of product. For areas with less
    than 24-inch clearance, the product may be applied by hand.

    D. Ambient temperature shall be within manufacturer’s specifications. (Greater than +20ºF/-


    7ºC.)

    E. All plumbing, electrical, mechanical and structural items to be under or passing through the
    vapor barrier/dampproofing membrane shall be positively secured in their proper positions
    and appropriately protected prior to membrane application.

    F. Vapor barrier/dampproofing membrane shall be installed before placement of reinforcing


    steel. When not possible, all exposed reinforcing steel shall be masked by General
    Contractor prior to membrane application.

    1.8 WARRANTY

    A. General Warranty: The special warranty specified in this Article shall not deprive the
    Owner of other rights the Owner may have under other provisions of the Contract
    Documents, and shall be in addition to, and run concurrent with, other warranties made by
    the Contractor under requirements of the Contract Documents.

    B. Special Warranty: Submit a written warranty signed by vapor barrier/dampproofing


    manufacturer and Installer, agreeing to repair or replace vapor barrier/dampproofing that
    does not meet requirements or that does not remain moisture resistant within the specified
    warranty period. Warranty does not include failure of vapor barrier/dampproofing material
    due to failure of substrate prepared and treated according to requirements or formation of
    new joints and cracks in the substrate.

    1. Warranty Period: 1 year after date of Substantial Completion.

    PART 2 – PRODUCTS

    2.1 MANUFACTURERS

    A. ECODAMP; Epro Services, Inc., Wichita, KS, 800-882-1896

    1. Spray-Applied ECODAMP.
    2. Detailing-mastic ECOLINE-T.
    3. Repair–grout QUIK-SET.

    2.2 DAMPPROOFING MATERIALS

    A. Fluid applied dampproofing system – ECODAMP: a single-course, high-build, polymer


    modified asphalt emulsion. Waterborne and spray applied at ambient temperatures. A
    nominal thickness of 20 dry mils (15 mil minimum), unless specified otherwise. Non-toxic
    and odorless. Manufactured by Epro Services, Inc.

    B. Fluid applied dampproofing physical properties.

    ECODAMP – TYPICAL CURED PROPERTIES (MEMBRANE ONLY)

    Elongation ASTM D 412-98a 5500%


    Tensile Strength ASTM D 412-98a 9 psi
    Hydrostatic Water Pressure ASTM D 751-00 10 psi
    Water Degradation ASTM D 2939-94 No Effect
    Adhesion ASTM C 836 11 lbf/inch
    Perm Rating ASTM E-96 .1049 gr./hr./sq. ft.
    Low Temp. Flexibility ASTM C 836-00 No Cracking at
    Ð6.7¼C
    Shrinkage ASTM C 836-00 0.03%
    Chemical or Environmental
    Resistance:
    Hydrochloric & Sulfuric 13%
    Acetic 30%

    2.3 AUXILIARY MATERIALS

    A. Sheet Flashing: 60-mil reinforced modified asphalt sheet good with double-sided adhesive.

    B. Reinforcing Strip: Manufacturer’s recommended polypropylene and polyester fabric.

    C. Repair grout: QUIK-SET a rapid curing, high-build mortar joint repair material.

    D. Joint Detailing Sealant Mastic: ECOLINE-T, a high viscosity polymer modified water based
    asphalt material.

    PART 3 – EXECUTION

    3.1 EXAMINATION
    A. Examine substrates, areas, and conditions under which vapor barrier/dampproofing
    materials will be applied, with Installer present, for compliance with requirements. Do not
    proceed with installation until unsatisfactory conditions have been corrected.

    3.2 SURFACE PREPARATION

    A. Clean and prepare substrate according to manufacturer’s recommendations. Provide


    clean, dust-free, and dry substrate for vapor barrier/dampproofing application. Power
    washing or sand blasting is an accepted cleaning method on existing structures.

    B. Mask off adjoining surfaces not receiving the vapor barrier/dampproofing to prevent
    spillage or over-spray affecting other construction.

    C. Close off deck drains and other deck penetrations to prevent spillage and migration of
    fluids.

    D. Remove grease, oil, form release agents, paints, and other penetrating contaminants from
    concrete.

    E. Remove fins, ridges, and other projections and fill honeycomb, aggregate pockets, grout
    joints, tie holes, and other voids with ECOLINE-T, hydraulic cement, or rapid-set grout.

    3.3 PREPARATION AND TREATMENT AT TERMINATIONS AND PENETRATIONS

    A. Prepare vertical surfaces at terminations, at penetrations through substrate, and at


    expansion joints and sleeves according to ASTM C 898 and manufacturer’s
    recommendations.

    B. Apply two coats of ECOLINE-T (30 mil each) and embed a joint reinforcing strip in
    preparation coat and apply a second coat over embedded joint reinforcing strip ensuring
    its complete saturation and covering.

    1. Terminations should be treated 6 inches up vertical and 6 inches on horizontal.


    2. Penetrations should be treated in a 6-inch radius around penetration and 3 inches onto
    penetrating object.

    3.4 PREPARATION AND TREATMENT OF JOINTS AND CRACKS

    A. Prepare, treat, rout, and fill joints and cracks in substrate according to ASTM C 898 and
    dampproofing manufacturer’s recommendations. Remove dust and dirt from joints and
    cracks complying with ASTM D 4258 prior to coating surfaces.

    B. Vertical - Apply two coats of ECOLINE-T mastic, 6 inches on each side of joint and embed
    a joint reinforcing strip in preparation coat and apply a second coat over embedded joint
    reinforcing strip ensuring to complete saturation and covering.
    3.5 VAPOR BARRIER/DAMPPROOFING APPLICATION

    A. Set up spray equipment according to manufacturer’s instructions.

    B. Mix materials according to manufacturer’s instructions.

    C. Start installing vapor barrier/dampproofing material in presence of manufacturer’s technical


    representative.

    D. Apply vapor barrier/dampproofing material, according to manufacturer’s recommendations,


    by spray.

    E. Apply one spray coat of ECODAMP to obtain a seamless membrane free of entrapped
    gases, with an average dry film thickness of 20 mils (1.0 mm) and a minimum dry film
    thickness of 15 mils (.875 mm) at any point.

    F. Apply vapor barrier/dampproofing material to prepared wall terminations and vertical


    surfaces to heights indicated according to manufacturer’s recommendations and details.

    G. Verify film thickness of vapor barrier/dampproofing membrane every 100 sq./ft. (9.3
    sq./m.).

    3.8 FIELD QUALITY CONTROL

    A. Membrane may be checked for coverage with a lightly oiled, needle nose depth gauge,
    taking four (4) readings over a one square inch area, every 500 square feet. Record the
    minimum reading. Mark the test area for repair.

    B. Test areas are to be patched over with ECODAMP to a 35- mil minimum dry thickness,
    extending a minimum of one-inch (1”) beyond the test perimeter.

    3.9 CURING, PROTECTING, AND CLEANING

    A. Cure vapor barrier/dampproofing membrane according to manufacturer’s


    recommendations, taking care to prevent contamination and damage during application
    stages and curing.

    B. Clean spillage and soiling from adjacent construction using cleaning agents and
    procedures recommended by manufacturer of affected construction.

    You might also like