Ordering number : ENN7244

Thick-Film Hybrid IC

STK412-000
Two-Channel Shift Power Supply Audio Power Amplifier ICs
60W + 60 W

Overview Package Dimensions

The STK412-000 series are class H audio power amplifier unit: mm
hybrid ICs that feature a built-in shift power supply 4196-SIP18
circuit. These Provide ICs high efficiency audio power
amplification by controlling (switching) the supply [STK412-000]
voltage supplied to the power transistors according to the
detected level of the input audio signal.
64.0
55.6 8.5
Features
• Pin compatible IC series that covers power ratings from

36.5
3.6
50 W × 2 channels to 180 W × 2 channels at 0.7 or 0.8%

25.8
18.7
THD, 20 Hz to 20 kHz. This allows the use of a 1 18
common PCB for all output classes. 2.54 0.5
2.9

4.0
• The pin arrangement is also unified with that of the (6.21) 17×2.54=43.18 0.4
5.5
three-channel STK413-000 series. This means that PCBs
designed for three-channel models can also be used for
two-channel models.
SANYO: SIP18
• Miniature package
— 50 W/ch to 120 W/ch (THD = 0.8%, f = 20 Hz to 20
kHz): 64 × 36.5× 8.5 mm*
— 150 W/ch to 180 W/ch (THD = 0.7%, f = 20 Hz to
20 kHz): 78 × 44× 9 mm*
* Not including the IC pins.
• Allowable load shorted time: 0.3 s

Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.

SANYO Electric Co.,Ltd. Semiconductor Company

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
20703AS (OT) No. 7244-1/4
 STK412-000

Series Organization
These products are organized into a series based on their output power.
Type No.
Parameter
STK412-090 STK412-000 STK412-010 STK412-020 STK412-030 STK412-040 STK412-150 STK412-170
Output (20 Hz to 20 kHz) 50 W + 50 W 60 W + 60 W 70 W + 70 W 80 W +80 W 100 W + 100 W 120 W + 120 W 150 W + 150 W 180 W + 180 W
[THD] [0.8 %] [0.8 %] [0.8 %] [0.8 %] [0.8 %] [0.8 %] [0.7 %] [0.7 %]
Maximum supply voltage, VH
±60 V ±65 V ±69 V ±73 V ±80 V ±84 V ±95 V ±95 V
(No signal)
Maximum supply voltage, VL
±41 V ±42 V ±44 V ±45 V ±46 V ±51 V ±61 V ±60 V
(No signal)
Recommended supply voltage,
±37 V ±39 V ±43 V ±45 V ±51 V ±54 V ±57 V ±54 V
VH
Recommended supply voltage,
±27 V ±29 V ±30 V ±32 V ±34 V ±36 V ±38 V ±37 V
VL
Recommended load impedance 8Ω 6Ω 4Ω
Package 64 mm × 36.5 mm × 8.5 mm 78 mm × 44 mm × 9 mm

Specifications
Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
VH: Maximum supply voltage 1 (no signal) VH max(1) ±65 V
VH: Maximum supply voltage 2 (signal present) VH max(2) RL = 8, 6 Ω ±57 V
VH: Maximum supply voltage 3 (signal present) VH max(3) RL = 4 Ω ±46 V
VL: Maximum supply voltage 1 (no signal) VL max(1) ±42 V
VL: Maximum supply voltage 2 (signal present) VL max(2) RL = 8, 6 Ω ±37 V
VL: Maximum supply voltage 3 (signal present) VL max(3) RL = 4 Ω ±29 V
VH-VL: Maximum supply voltage *4 VH-L max No load 60 V
Thermal resistance θj-c Per power transistor 1.9 °C/W
Junction temperature Tj max 150 °C
Both the Tjmax and Tcmax conditions must be met.
Operating IC substrate temperature Tc max 125 °C
Storage temperature Tstg –30 to +125 °C
VH = ±39 V, VL = ±29 V, RL = 8 Ω, f = 50 Hz, PO = 60 W, 0.3 s
Allowable load shorted time *3 ts one channel operating

Operating Characteristics at Ta = 25°C, RL = 8 Ω, Rg = 600 Ω, VG = 40 dB, VZ = 15 V, RL must be a non-

inductive load.
Test conditions *1 Standard value
Parameter Symbol Unit
VCC (V) f (Hz) PO (W) THD (%) min typ max
VH = ±39
PO (1) 20 to 20 k 0.8 60 W
VL = ±29
Output power
VH = ±32
PO (2) 1k 0.8 RL = 4 Ω 60 W
VL = ±24
VH = ±39
Total harmonic distortion THD 20 to 20 k 60 0.4 %
VL = ±29
VH = ±39
Frequency characteristics fL, fH 1.0 +0 –3 dB 20 to 50 k Hz
VL = ±29
VH = ±39
Input impedance ri 1k 1.0 55 kΩ
VL = ±29
VH = ±47
Output noise voltage *2 VNO Rg = 2.2 kΩ 1.0 mVrms
VL = ±31
VH = ±47 No load 30 mA
Quiescent current ICCO
VL = ±31 No load 100 mA
VH = ±47
Midpoint voltage VN –70 0 +70 mV
VL = ±31

Notes: *1. Unless otherwise specified, a constant-voltage power supply must be used during inspection.
*2. The output noise voltage rating gives the peak value read by an averaging VTVM. However, to eliminate the influence of flicker noise from the AC
primary side line, use an AC stabilized power supply (50 Hz).

No. 7244-2/4
 STK412-000

*3. Use the transformer power supply specified in the figure below for allowable load shorted time and output noise voltage measurements.
*4. Design circuits so that (|VH| - |VL|) is always less than 40 V when switching the power supply with the load connected.
*5. Set up the VL power supply with an offset voltage at power supply switching (VL - LO) of about 8 V as an initial target.

DBA40C 10000µF DBA40C 10000µF

+VH +VL
+ +
500Ω 500Ω

+ +
500Ω 500Ω
--VH --VL
10000µF 10000µF

Specified Transformer Power Supply Specified Transformer Power Supply

(MG-250 equivalent) (MG-200 equivalent)

Internal Equivalent Circuit

1
R41

TR41
13 D12
TR9 TR19 Comparator
TR1 TR2 D2 R3 R13 TR12 TR11 3
D42
TR6 TR16
C2 C12
C1 C11 D43
2
R1 R11 D41
TR3 TR4 TR8 TR10 TR20 TR18 TR14 TR13
14 R4 R14

15
R5 R15
D51
16
R6 R16 5
TR5 TR7 TR17 TR15 D53

R2 D1 R7 R17 R12
D52
4
12
Comparator

TR51
7
R51
SUB 6

9 8 11 10 17 18

No. 7244-3/4
 STK412-000

Sample Application Circuit

STK412-000 Series

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

56kΩ 100pF 100pF

*1 *1 *1 *1
56kΩ
2.2µF
3pF 33kΩ
/50V 1kΩ
Ch.2 IN
3pF 560Ω 560Ω
56kΩ 470pF
100Ω GND
100µF 100µF 2.2µF
/1W /10V /10V 56kΩ /50V 470pF
+VH
100µF GZA GZA Ch.1 IN
/63V 15X 15X 1kΩ
+VL 100µF 3µH
100µF /100V Ch.2 OUT
1.5kΩ 0.1µF
/50V /1W 1.5kΩ
4.7Ω 4.7Ω
/1W
GND /1W
GND
100µF 4.7Ω
/50V 100µF 3µH /1W
--VL 0.1µF
/100V Ch.1 OUT
100µF
/63V
--VH 4.7Ω
100Ω
/1W

SUB.GND *1: Cement resistor, 0.22 Ω, ±10% (5 W)

Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification”
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.

This catalog provides information as of February, 2003. Specifications and information herein are subject
to change without notice.

PS No. 7244-4/4