WSR T2 112011 HK

TempTrackr Wireless
WSR-T2 Wireless SAW Reader
WSR-T2
The WSR-T2 Reader provides a base for batteryless, non-invasive and low cost temperature measurement solution that is ideally suited for applications ranging from industrial to consumer markets. The WSR-T2 Reader is a highly sophisticated SAW Sensor interrogation unit. The WSR-T2 is designed to monitor multiple Sensors simultaneously. SenGenuity will work closely with you to adapt the WSR-T2 Reader to meet the specific needs of your application.
Features
Batteryless Wireless Temperature Sensors Multiple Sensor Tracking Capability 2 m Interrogation Distance1 Typical Sensor Temperature Range: -10C up to 120C (Others on Request) Wireless Reader can be powered by Laptop / PC User friendly, simple to use interface Plug-n-play sensor connectivity and installation
Applications
Temperature measurement High cycle rate applications (i.e. reciprocating machinery) Measurement on rotating parts Measurement in harsh environment Highly constricted space for sensor Measurement where power to the sensor is not possible
Block Diagram
Page 1 of 7
267 Lowell Rd, Hudson NH 03051, USA
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com
Performance Specifications Interrogation unit

Standard measurement: Temperature (other measurands please contact factory) Parameter
Frequency range
2
Min
429 +6 -95 -20 -32 -1.5 -0.5
Typical
Max
438
Units
MHz dBm dBm C Hz kHz kHz
Condition
Refer to FCC/CE Certification detail in Notes power can be reduced by software settings per sensor operating temperature range for reader unit Reader @25C and -75 dBm input power at time of shipment -20 to +60C
Maximum output power 2 Input power Operating temperature range Resolution Initial accuracy Accuracy vs. operating temperature range (referenced to +25C) Accuracy vs. aging / 5 years Measurement time Number of sensors Supply voltage Supply voltage Power consumption Length Height Width Weight Length Height Width Weight Length Height Width Weight Interface connector Antenna connector Power connector Power connector Power connector
+10 -50
+13 0 +60 +32 +1.5 +0.5
-1.5 50 1 +3.8 +9 1.1 +5.0 +24 1.5 91 10 50 30 96 35 57 110 96 45 57 140 CAN
+1.5
kHz ms depends on settings and number of interrogations per measurement 6 Sensors per antenna Reader Option A1 Reader Option A2 and A3
18
pieces VDC VDC W mm mm mm
Power Supply
+5.25 +30 2.2
Mechanical Specifications Reader unit

Reader Option A1 and E0 Reader Option A1 and E0 Reader Option A1 and E2 Reader Option A1 and E2 Reader Options A2, A3 and E2 Reader Options A2, A3 and E2 Additional Interfaces see Options Reader Option A1 Reader Option A2 and A3 Reader Option B6
50
g mm mm mm
130
g mm mm mm
160
Pinning and connectos

3 x SMA DC Power connected through CAN interface Screw Terminals DC Power connected through USB Mini
Page 2 of 7
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com
Absolute Maximum Ratings

Humidity Operable Temperature Range Storage Temperature Range CAN Interface Pin S2/1 CAN Interface Pin S2/2 CAN Interface Pin S2/3 CAN Interface Pin S2/4 RS232 Interface Pin S3/1 RS232 Interface Pin S3/2 RS232 Interface Pin S3/3 RS232 Interface Pin S3/4 RS485 Interface Pin S3/1 RS485 Interface Pin S3/2 RS485 Interface Pin S3/3 RS485 Interface Pin S3/4 Screw Terminal +9..30V DC Screw Terminal GND Screw Terminal RS485 A Screw Terminal RS485 B Screw Terminal 4-20mA Screw Terminal 0.5..5V Out Screw Terminal 0..3V Out Antenna Connectors Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 0 0 0 NA NA +5.5 +3.8 +3.8 V V V V V -8 -8 0 0 0 -8 -8 0 NA +13 +13 Supply +7 +3.3 V V V V V -13 -24 0 NA +13 +13 +30 V V V -6 -6 0 NA +13 +24 +7 V V V -30 -40 0 NA +15 +15 +7 V V V 80 +60 +70 +7 % C C V Option A1, Supply GND CANL CANH Option B1, Supply Option B1 Option B1 Option B1 Option B5, Supply Option B5 Option B5 Option B5 Option A2 and A3, Supply Option A2 and A3 Option B2, B3, and B4 Option B2, B3, and B4 Option C1 Option C2 Option C3 No DC Voltage allowed Option B6, Supply Option B6 Option B6 Option B6 Option B6 without condensation
Page 3 of 7
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com
Outline Drawing / Enclosure Option A1 and E0

Pin Connections
Pin 1 2 3 4 S2 +5V GND CANL CANH Option B1 S3 +5V GND RS232_TX# RS232_RX# Option B5 S3 +5V GND RS485BRS485A+
# Lines must be crossed when connected to other devices
Outline Drawing / Enclosure Options A1 and E2
Drawing does not show clip for TS-35
Page 4 of 7
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com
Outline Drawing / Enclosure Options A2, A3 and E2
Drawing does not show clip for TS-35
WSR-T2- Contents
One Wireless Sensor Reader with selected Options see ordering Information. If additional components, like: Reader antennae, PC interface Software User Manual Sensor Modules Power Supply are required please ask for a Kit
Page 5 of 7
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com
WSR-T2 Reader Options3

Option
A1 A2 A3
4
Options see ordering code3

Supply Voltage 5 V Supply voltage 9.. 30 V, no DC Isolation Supply Voltage 9..30 V, DC Isolation RS232 Output RS485 - Full Duplex Isolated RS485 - Half Duplex, 2 Terminals per signal, Isolated RS485 - Half Duplex , 1 Terminal per signal, Isolated RS485 - Half Duplex , 1 Terminal per signal, Not Isolated USB Mini Isolated Analog Outputs 2 x 4-20 mA self powered Isolated Analog Outputs 2 x 0.5..5 V Unisolated Analog Outputs 2 x 0.0..3.0 V With Housing and Clip for TS-35
Condition
No Daugthercard required Daugthercard stacked on reader Daugthercard stacked on reader Default Option Option not available with Option A1 Option not available with Option A1 Option not available with Option A1
B1 B2 B3 B4 B5 B6 C1 C2 C3 E2
Option not available with Option A1, B2 and B3 Option not available with Option A1, B2 and B3 Option not available with Option A1, B2 and B3 package Option is recommended for A2, A3
Ordering Information3
WSR - T2 - A1
B1
C1
D0
E2
WSR - T2 Supply Voltage Required Option A1: 5 V A2: 9..30 V, no DC Isolation A3: 9..30 V, DC Isolation Additional interface B1: RS232 Output Default Option B2: RS485 Full duplex, Isolated B3: RS485 Half duplex 2 Terminals per signal, Isolated B4: RS485 Half duplex 1 Terminal per signal, Isolated B5: RS485 Half duplex 1 Terminal per signal, Non Isolated B6: USB Analog Outputs C1: Isolated 2 x 4-20 mA self powered C2: Isolated 2 x 0.5..5 V C3: Unisolated 2 x 0.0..3.0 V C0: if not required Display Connector D0: available option Package E2: with housing and Clip for TS-35 E0: if not required Note: Options within one Letter code can not be combined Options A2, A3, B2, B3, B4, C1, C2, C3 are connected via screw terminals
Notes:
1) Dependent on RF environment. 2) FCC/CE Certification refer to: ADVISORY for COMPLIANCE to COUNTRY DIRECTIVE(S) 3) Not all combinations are available, please contact factory for availability. 4) Power Supply must be able to provide 500mA Start-Up-Current with Option A3
Product status and specifications are subject to change.

DISCLAIMER Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Rev: 11/2011 Page 6 of 7
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com
Advisory for Compliance to Country Directive(s)/Regulations

Vectron International readers and/or kits are considered electrical apparatus that may require compliance to specific country Directive(s)/regulations when put in service for end-use. Vectron offers certain WSR products (typically as kits) that have been tested and certified to be fully compliant to such directives/regulations and marked accordingly with the required markings such as FCC logo or CE markings. Product with FCC/CE markings when shipped by Vectron, must be used in accordance with the requirements of the standards that the product has been tested to comply with (Refer to the User Manual/Instructions and safety precautions). A declaration of conformity can be provided upon request or obtained from Vectrons web site: www.sengenuity.com Vectron may also offer un-marked product sold as a component or sub- assembly. Standalone WSR reader boards/sub-assemblies which function as described in this data-sheet for example, may be shipped without such markings as permitted by the regulations. Such un-marked product is intended for further processing and assembly by customers into their own products with a view to putting such product on the market for service or end-use under their own name. When Vectron ships unmarked product (e.g. without CE marking), customers are advised and cautioned that, as the manufacturer of the product, they should review the directives/standards for their country for EMC (e.g. 2004/108/EC for EU Community) and/or other directives as applicable, to ensure compliance to these directives when they put their end-product incorporating the Vectron component on the market. For further guidance for EU use on this subject, please refer to : http://ec.europa.eu/enterprise/policies/single-market-goods/files/blue-guide/guidepublic_en.pdf Details of Operating Instructions/User Manual including the criteria or set of operating conditions/commands that can affect EMC compliance are provided in: http://www.sengenuity.com/prods_spec_sheets.html/xxx Note: The set of conditions that can render the product compliant or non-compliant is being provided for guidance only, and is not intended to assurance of such compliance or noncompliance which will be influenced by the actual customer applications and use environment. Customers are ultimately responsible for the assessment of any compliance.
Page 7 of 7
Phone: 1.888.328.7661
Fax: 1.888.329.8328
www.sengenuity.com

WSR T2 112011 HK

Uploaded by

Copyright:

Available Formats

WSR T2 112011 HK

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WSR T2 112011 HK

Uploaded by

Copyright:

Available Formats

TempTrackr Wireless

WSR-T2 Wireless SAW Reader

267 Lowell Rd, Hudson NH 03051, USA

Performance Specifications Interrogation unit

+13 0 +60 +32 +1.5 +0.5

-1.5 50 1 +3.8 +9 1.1 +5.0 +24 1.5 91 10 50 30 96 35 57 110 96 45 57 140 CAN

pieces VDC VDC W mm mm mm

Mechanical Specifications Reader unit

Pinning and connectos

267 Lowell Rd, Hudson NH 03051, USA

Absolute Maximum Ratings

267 Lowell Rd, Hudson NH 03051, USA

Outline Drawing / Enclosure Option A1 and E0

# Lines must be crossed when connected to other devices

Outline Drawing / Enclosure Options A1 and E2

Drawing does not show clip for TS-35

267 Lowell Rd, Hudson NH 03051, USA

Outline Drawing / Enclosure Options A2, A3 and E2

Drawing does not show clip for TS-35

267 Lowell Rd, Hudson NH 03051, USA

WSR-T2 Reader Options3

Options see ordering code3

Product status and specifications are subject to change.

Rev: 11/2011 Page 6 of 7

267 Lowell Rd, Hudson NH 03051, USA

Advisory for Compliance to Country Directive(s)/Regulations

267 Lowell Rd, Hudson NH 03051, USA

You might also like