A Presentation On Sms-2

By Name:- Rajesh Kumar Patel Roll no:- 3203809035
INTRODUCTION
STEEL :-
Steel is not a specific product. It is essentially a malleable alloy of iron and one or more elements like carbon, chromium, Silicon, vanadium, etc. Steel making is a refining or oxidation process with the exception of reducing condition being specifically required to eliminate sulphur.
FACILITIES AT SMS-II (JSPL)
ANNUAL CAPACITY ELECTRIC ARC FURNACE LADLE REFINING FURNACE VACCUM DEGASSER RH DEGASSER CONTINOUS CASTER
2.0 MT 02 NO. 03 NO. 01 NO. 01 NO. 03 NO.
Electric Arc Furnace (EAF)

Electric Arc Furnace (EAF) is a steel making furnace, in which steel scrap is heated and melted by heat of electric arcs striking between the furnace electrodes and the metal bath. Three-phase AC Electric Arc Furnaces with graphite eiectrodes are commonly used in steel making.
Structure of an Electric Arc Furnace
ELECRIC ARC FURNACE

SALIENT FEATURES
MAKE CAPACITY TRANSFORMER RATING ELECTRODE DIAMETER SMS DEMAG 100 MT 100 MVA 600 mm
No. OF VLB (For oxygen Lancing) 4 FURNACE LINING BRICKS TAP HOLE Magnesia Carbon Bricks EBT TYPE
Ladle refining furnace (LRF)

Mainly this comes under the secondary steel making process. And as the name suggest In this furnace the refinement of the liquidous steel is done, which is brought from the Electric arc furnace. The liquidous steel which we obtain after decarburization is used as input for the LRF. It also plays important role for deciding the grade of the steel.
Schematic Diagram to Show LRF
SALIENT FEATURES:- Ladle Refining Furnace No. of LRF : 3 Make : SMS DEMAG Capacity : 100 T each Transformer Rating : 18 MVA
Importance Of LRF:
Its main function is reducing impurities. This zone is usually used to reduce the sulphur presence in the hot metal. Sulphur presence is controlled between 0.2 0.4. Its excess presence leads to the hot shortness which increase the difficulty during the hot rolling process. Afterwards from LRF the refined hot metal is passed into degasifier zone to remove the presence of gas. This is mainly done by these two processes 1). Vaccum Degasser 2). RH- Degasser
After refinement hot molten steel is brought in caster section where the desired shape and size is provided. Caster which is used for casting is also known as continuous casting machine.
There is mainly three types caster which is used

COMBI CASTER BILLET CASTER SLAB CASTER
COMBI CASTER
This section is mainly responsible for the tonnage production of the bloom, beam blank and round bars. This is none other than the combicaster at Jspl. The mould in combicaster can be changed as per the requirement to produce the various products. There are total of 4 mould used for production of products. There are various,shapes and sizes. It is provided, with mould oscillator, to oscillate the system. cooling bed cylinder. It is made, of copper plate.
Mould of the caster:
Features of Combi Caster:

No. of strands Supplier Radius Machine speed Speed range Mould length Dummy bar system (Bottom feeding) Type of mould
Cut length
: : :
: : : :
04 VAI 12000 mm
0 to 2.5 m/min 800 mm Chain type dummy bar Curved mould with Cu plates for beam blank and Blooms, Cu tube for rounds. 4.5 to 12 mtrs
Billet Caster
The Billet Caster here at JSPL, Raigarh, is a 6 strand continuous casting machine capable of producing billets of both round and square cross section of various cross section, details of which is given below.
SQUARE (Side in mm) 130 150 165 200
ROUND (dia in mm) 142 162 180 200 220
Features of Billet Caster:

No of Strands : 06 Radius : 9000 mm Mode of straightening : Continuous Machine speed : Speed range = 0 to 5 m/min Restranding speed = 3.5 m/min Length from meniscus : 27.1 meter In mould to torch cutter Mould length : 800 mm(Rounds) 1000 mm (Squares) Metallurgical Length : 27.1 meter Dummy bar system : Rigid type dummy bar Mould level control : Co60 source with stopper rod Control Cut Length : 9 to 12 meter Type of mould : Curved tublar Cu mould
Slab caster:
Slab caster is an important functional part in any of the steel industry. It is the place where the hot, molten steel is brought with the help of ladle and poured into tundish , which slowly regulates the steel into the mould and provided with the initial support of the dummy bar the required shape and size of the slab is achieved.
The required process flowshet for slab.
Sections of a slab caster
These are the major portions of the slab caster unit.
Diagram of the continuous caster producing slab.
Features of slab Caster:

No of Strands : 01 Supplier : SMS DEMAG Radius : 12000 mm Mode of straightening : Single point Machine speed : Speed range = 0 to 2 m/min Restranding speed = 1.2 m/min Mould length : 700 mm Metallurgical Length Dummy bar system Mould level control Control Cut Length Type of mould : 17.3 meter : Chain type dummy bar : Co60 source with stopper rod : 3.5 to 9 meter : Curved mould with Cu mould
SEMI PRODUCTS OF SMS-II
Thank You

A Presentation On Sms-2

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A Presentation On Sms-2

Uploaded by

Copyright:

Available Formats

By Name:- Rajesh Kumar Patel Roll no:- 3203809035

FACILITIES AT SMS-II (JSPL)

2.0 MT 02 NO. 03 NO. 01 NO. 01 NO. 03 NO.

Electric Arc Furnace (EAF)

Structure of an Electric Arc Furnace

ELECRIC ARC FURNACE

Ladle refining furnace (LRF)

Schematic Diagram to Show LRF

There is mainly three types caster which is used

Mould of the caster:

Features of Combi Caster:

SQUARE (Side in mm) 130 150 165 200

ROUND (dia in mm) 142 162 180 200 220

Features of Billet Caster:

The required process flowshet for slab.

Sections of a slab caster

These are the major portions of the slab caster unit.

Diagram of the continuous caster producing slab.

Features of slab Caster:

SEMI PRODUCTS OF SMS-II

You might also like