OpAmp F10

Greg Henderson
Abdul Jaroudi
Nishanth Mehanathan
What is an Op-Amp?
Characteristics of Ideal and Real
Op-Amps
Common Op-Amp Circuits
Applications of Op-Amps
References

An Operational Amplifier (known as an
Op-Amp) is a device that is used to
amplify a signal using an external power
source
Op-Amps are generally composed of:
Transistors, Resistors, Capacitors

= + +
First patent for Vacuum Tube Op-Amp (1946)

First Commercial Op-Amp available (1953)
First discrete IC Op-Amps (1961)
First commercially successful Monolithic Op-Amps
(1965)
Leading to the advent of the modern IC which is still used
even today (1967 present)
Fairchild A741

Electrical Schematic of A741
A traditional Op-Amp:
: non-inverting input
: inverting input
: output
: positive power supply
: negative power supply

V
+

V
-

V
out

V
s+

V
s-

The difference between the two inputs voltages (V
+
and V
-
) multiplied by the
gain (K, amplification factor) of the Op-Amp gives you the output voltage

The output voltage can only be as high as the difference between the
power supply (V
s+
/ V
s-
)and ground (0 Volts)
V
out
= K (V
+
- V
-
)
V
in
V
out
V
S+
V
S-
Slope = K (gain of
Op-Amp)
The slope is normally much steeper
than it is shown here. Potentially just
a few milli-volts (mV) of change in
the difference between V
+
and V
-

could cause the op-amp to reach
the saturation level
Saturation is caused by increasing/decreasing
the input voltage to cause the output voltage
to equal the power supplys voltage*
Saturation
Points
* Note that saturation level of
traditional Op-Amp is 80% of
supply voltage with exception
of CMOS op-amp which has a
saturation at the power
supplys voltage
What is an Op-Amp?
Op-Amps
References

Infinite voltage gain
Infinite input impedance
Zero output impedance
Infinite bandwidth
Zero input offset voltage (i.e., exactly
zero out if zero in).

http://hyperphysics.phy-astr.gsu.edu/hbase/electronic/opamp.html#c4
http://hyperphysics.phy-astr.gsu.edu/hbase/electronic/opamp.html#c4
Parameter Ideal Op-Amp Real Op-Amp
Differential Voltage Gain

10
5
- 10
9

Gain Bandwidth Product (Hz)

1-20 MHz
Input Resistance (R)

10
6
- 10
12

Output Resistance (R) 0 100 - 1000
Ideal
Real
What is an Op-Amp?
Op-Amps
References

An op-amp amplifies the difference of the inputs V
+

and V
-
(known as the differential input voltage)
This is the equation for an open loop gain amplifier:

K

is typically very large at around 10,000 or
more for IC Op-Amps
This equation is the basis for all the types of amps
we will be discussing
V
out
=K(V
+
-V
-
)
A closed loop op-amp has feedback from the
output to the input, an open loop op-amp does
not

Open Loop Closed Loop
Amplifies the input voltage by
a constant
Closed loop op-amp
Voltage input connected to
non-inverting input
Voltage output connected to
inverting input through a
feedback resistor
Inverting input is also
connected to ground
Non-inverting input is only
determined by voltage output

R
1
/(R
1
+R
2
) Voltage Divider
V
-
=V
out
(R
1
/(R
1
+R
2
) )
V
out
=[V
in
-V
out
(R
1
/(R
1
+R
2
))] K
V
out
=V
in
/[(1/K)+ (R
1
/(R
1
+R
2
))]
As discussed previously assuming, K is very large, we have:
V
out
=V
in
/(R
1
/(R
1
+R
2
))
V
out
=V
in
(1+(R
2
/R
1
))
V
out
=K(V
+
-V
-
)
Amplifies and inverts the input
voltage
Closed loop op-amp
Non-inverting input is determined
by both voltage input and output
The polarity of the output voltage is
opposite to that of the input
voltage
Voltage input is connected to
inverting input
Voltage output is connected to
inverting input through a feedback
resistor
Non-inverting input is grounded

V
out
=K(V
+
-V
-
)
V
-
=V
out
(R
in
/(R
in
+R
f
))+V
in
(R
f
/(R
in
+R
f
))
V
-
=(V
out
R
in
+V
in
R
f
)/(R
in
+R
f
)
V
out
=K(0-V
-
)
V
out
=-V
in
R
f
/[(R
in
+R
f
)/K+(R
in
)]
V
out
=-V
in
R
f
/R
in

Integrates the inverted input
signal over time
Closed loop op-amp
Voltage output is connected
to inverting input through a
capacitor
The resistor and capacitor
form an RC circuit
Magnitude of the output is
determined by length of time
voltage is present at input
The longer the input voltage is
present, the greater the
output

When the circuit is first connected the capacitor acts
as a short. Gain is less than 1, V
out
is 0
As time progresses, and the capacitor charges, its
effective resistance increases. Now V
out
is increasing as
well
When the capacitor is fully charged it acts as an open
circuit with infinite resistance. Now V
out
goes into
saturation (~80% power supply voltage)
The rate of voltage output increase depends on the RC
time constant

V
out
=-V
in
R
C
/R
in

d V
RC
1
V
t
0
in out
An integrating op-amp circuit can create a
sawtooth signal if a square wave is applied at
V
in

Voltage relations
The purpose of the differential amplifier is to produce an
output proportional to the difference of the input voltages
V
+
is given by the voltage divider equation
Output voltage
V
out
as we see is the difference of voltage V1 & V2 multiplied
by the resistance R4 & R3 which scales the difference
Output voltage
The summing amplifier does exactly as the name suggests by adding up the
voltages given to it and producing an output voltage which is the sum of the
input voltages scaled by the feedback resistance and input resistance
The graph shown above is a plot of output voltage V
out
vs input voltage V
in
3
What is an Op-Amp?
Op-Amps
References

R
2
+
-

+

V
0

__

+ V
cc

- V
cc

-
+
Types:
Low pass filter
High pass filter
Band pass filter
Cascading (2 or more filters connected
together)

R
1

C
Low pass filter
Low pass filter
Cutoff frequency
Low pass filter transfer
function
Use a Wheatstone bridge to
determine the strain of an
element by measuring the
change in resistance of a
strain gauge

(No strain) Balanced Bridge
R #1 = R #2

(Strain) Unbalanced Bridge
R #1 R #2

R + R
R
f
+

+

V
0

__

+ V
cc

- V
cc

-
+
R
f
V
ref
Half-Bridge Arrangement
R
R - R
R
Using KCL at the inverting and non-
inverting terminals of the op amp we find
that
~ V
o
= 2R(R
f
/R
2
)
Op amp used to
amplify output from
strain gauge
-
Goal is to have V
SET
= V
OUT

Remember that V
ERROR
= V
SET
V
SENSOR
Output Process uses V
ERROR
from the PID controller to adjust V
out

such that it is ~V
SET

P

I

D

Output
Process
Sensor
V
ERROR
V
SET

V
OUT

V
SENSOR

PID Controller System Block Diagram
Signal conditioning allows you to
introduce a time delay which could
account for things like inertia
System to control
Source: http://www.ecircuitcenter.com/Circuits/op_pid/op_pid.htm
-V
SENSOR

V
ERROR

Adjust Change
K
p
RP1, RP2
K
i
RI, CI
K
d
RD, CD
V
ERROR PID
1. Student lecture Fall 2009, Andrew Gibson, Konstantin Froelich,
Benjamin Haefner, Roshan Kalghatgi.
http://www.me.gatech.edu/mechatronics_course/
2. PID controller http://en.wikipedia.org/wiki/PID_controller
3. Operation amplifier applications
http://en.wikipedia.org/wiki/Operational_amplifier_applications
4. http://www.wisc-online.com/
5. http://hyperphysics.phy
astr.gsu.edu/hbase/electronic/opamp.html#c4

OpAmp F10

Uploaded by

Copyright:

Available Formats

OpAmp F10

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

OpAmp F10

Uploaded by

Copyright:

Available Formats

Greg Henderson

You might also like