Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
480 views

Vlsi Implementation OF Ofdm

This document discusses the VLSI implementation of an OFDM transceiver. It begins with an introduction to OFDM and its advantages over single carrier systems. It then describes the basic blocks of an OFDM transceiver including the transmitter and receiver. The document focuses on the design methodology for implementing an OFDM baseband in VLSI including algorithm simulation, hardware design considerations like interfaces and clocking, and optimization of circuits like multipliers. The goal is to present an approach for designing an OFDM modem chip with low cost, low power consumption and high performance.

Uploaded by

venchinn4676
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
480 views

Vlsi Implementation OF Ofdm

This document discusses the VLSI implementation of an OFDM transceiver. It begins with an introduction to OFDM and its advantages over single carrier systems. It then describes the basic blocks of an OFDM transceiver including the transmitter and receiver. The document focuses on the design methodology for implementing an OFDM baseband in VLSI including algorithm simulation, hardware design considerations like interfaces and clocking, and optimization of circuits like multipliers. The goal is to present an approach for designing an OFDM modem chip with low cost, low power consumption and high performance.

Uploaded by

venchinn4676
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 15

VLSI IMPLEMENTATION

OF
OFDM
 Presented By
B.VENKATESH
Y.ARUN KUMAR

    
ADITYA institute of technology and management,
TEKKALI,
SRIKAKULAM DIST.
                
Abstract:
Ø   orthogonal Frequency Division Multiplexing(OFDM) is a
multi-carrier system where data bits are encoded to
multiple sub-carriers and sent simultaneously in time.
The result is an optimum usage of bandwidth
 
Although OFDM in theory has been in existence for a
long time, recent developments in DSP and VLSI
technologies have made it a feasible option.

OFDM is fast gaining popularity in broadband standards


and high-speed wireless LAN.
 
INTRODUCTION
ØOFDM offers several advantages over single carrier system.
ØOFDM is a multi-carrier system where data bits are encoded to multiple
sub-carriers
ØThe frequencies used in OFDM system are orthogonal
ØNeighboring frequencies with overlapping spectrum can therefore be used.
ØThis property is shown in the figure where f1, f2 and f3 orthogonal.
ØThis results in efficient usage of BW. The OFDM is therefore able to
Øprovide higher data rate for the same BW.
2.OFDM TRANCEIVER

Block diagram of an OFDM transceiver


3.VLSI IMPLEMENTATION

ØLower gate count compared to


DSP+RAM+ROM, hence lower cost
ØLow power consumption

4.DESIGN METHODOLOGY

Ø Early in the development cycle, different communication and signal


processing algorithms are evaluated for their performance under different
conditions like noise, multipath channel and radio non-linearity.
DESIGN FLOW FOR BASE BAND DEVELOPMENT
5.ARCHITECTURE DEFINITION

Specifications of the OFDM transceiver:

•Data rates to be supported


•Range and multipath tolerance
•Indoor/Outdoor applications
•Multi-mode: 802.11a only or 802.11a+HiperLAN/2
5.2 Design trade-offs
•
•Smaller the die size lesser the chip cost
•Low power crucial for battery operated mobile devices
•Ease of implementation
•Customizability
6. Algorithm survey & simulation
•
•Channel estimation and compensation for different channel models
(Rayleigh, Rician, JTC, Two ray) for different delay spreads
Compensation for Phase noise and error in Frequency offset estimation
•System tolerance for I/Q phase and amplitude imbalance
•Wave shaping filter to get the desired spectrum mask
Frequency estimation algorithm for different SNR and frequency offsets

6.1 FIXED SIMULATION

6.2 SIMULATION SET UP


7. Hardware design:
7.1 Interface definition
Base band interfaces with two external modules: MAC and Radio.

7.1.1 Interface to MAC


Base band should support the following for MAC
•Should support transfer of data at different rates
•Transmit and receive control
•RSSI/CCA indication
•Register programming for power and frequency control

Following options are available for MAC interface:


•Serial data interface
•Varying data width, single speed clock
7.1.2 Interface to Radio:
Two kinds of radio interfaces are described below
•
•I/Q interface
On the transmit side, the complex Base band signal is
sent to the radio unit that first does a Quadrature modulation
followed by up-conversion at 5 GHz. On the receive side,
following the down-conversion to IF, Quadrature
demodulation is done and complex I/Q signal is sent to Base
band.
•IF interface
The Base band does the Quadrature modulation and
demodulation digitally.

Figure: IF interface:
7.2 Clocking strategy
The clock scheme chosen for the Base band should be able to
support all rates and also result in low power consumption.

Two options are shown below:

•Above scheme requires different clock sources or a very


high clock rate from which all these clocks could be
generated.
•The modules must work for the highest frequency of 54
MHz.
•Shown in the previous figure is a simpler clocking scheme with only one
clock speed for all data rates
•Varying duty cycles for different data rates is provided by the data enable
signal
•All the circuits in the transmit and receive chain work on parallel data (4
bits)
•Overhead is the Data enable logic in all the modules
7.4 Optimize the widely used circuits
7.4.1 Multipliers
They are the most widely used circuits. Synthesis tools usually provide
highly optimized circuits for multipliers and adders.

7.4.2 ACS unit


There are 64 instantiations of ACS unit in the Viterbi decoder.
Optimization of ACS unit results in significant savings.

8. Conclusion
In this paper, design approach for an OFDM Modem was
presented. Different algorithms implemented in OFDM modem
are identified.
The need for verifying the algorithms in the same
environment or the same set of test vectors with which the
Fixed-point "C" implementation of algorithms are run is
highlighted.

You might also like