Chapter 3: Pressure and Fluid Statics: Eric G. Paterson

Chapter 3: Pressure and Fluid Statics
Eric G. Paterson
Department of Mechanical and Nuclear Engineering
The Pennsylvania State University
Spring 2005
Note to Instructors
These slides were developed1 during the spring semester 2005, as a teaching aid
for the undergraduate Fluid Mechanics course (ME33: Fluid Flow) in the Department of
Mechanical and Nuclear Engineering at Penn State University. This course had two
sections, one taught by myself and one taught by Prof. John Cimbala. While we gave
common homework and exams, we independently developed lecture notes. This was
also the first semester that Fluid Mechanics: Fundamentals and Applications was
used at PSU. My section had 93 students and was held in a classroom with a computer,
projector, and blackboard. While slides have been developed for each chapter of Fluid
Mechanics: Fundamentals and Applications, I used a combination of blackboard and
electronic presentation. In the student evaluations of my course, there were both positive
and negative comments on the use of electronic presentation. Therefore, these slides
should only be integrated into your lectures with careful consideration of your teaching
style and course objectives.
Eric Paterson
Penn State, University Park
August 2005
1 These
slides were originally prepared using the LaTeX typesetting system (http://www.tug.org/)
and the beamer class (http://latex-beamer.sourceforge.net/), but were translated to PowerPoint for
wider dissemination by McGraw-Hill.
ME33 : Fluid Flow
Pressure
Pressure is defined as a normal force
exerted by a fluid per unit area.
Units of pressure are N/m2, which is called
a pascal (Pa).
Since the unit Pa is too small for pressures
encountered in practice, kilopascal (1 kPa
= 103 Pa) and megapascal (1 MPa = 106
Pa) are commonly used.
Other units include bar, atm, kgf/cm2,
lbf/in2=psi.
ME33 : Fluid Flow
Absolute, gage, and vacuum pressures

Actual pressure at a give point is called
the absolute pressure.
Most pressure-measuring devices are
calibrated to read zero in the atmosphere,
and therefore indicate gage pressure,
Pgage=Pabs - Patm.
Pressure below atmospheric pressure are
called vacuum pressure, Pvac=Patm - Pabs.
ME33 : Fluid Flow
Absolute, gage, and vacuum pressures
ME33 : Fluid Flow
Pressure at a Point
Pressure at any point in a fluid is the same
in all directions.
Pressure has a magnitude, but not a
specific direction, and thus it is a scalar
quantity.
ME33 : Fluid Flow
Variation of Pressure with Depth

In the presence of a gravitational
field, pressure increases with
depth because more fluid rests
on deeper layers.
To obtain a relation for the
variation of pressure with depth,
consider rectangular element
Force balance in z-direction gives
maz 0
P2 Dx P1Dx g DxDz 0
Dividing by Dx and rearranging

gives
DP P2 P1 g Dz s Dz
ME33 : Fluid Flow
Variation of Pressure with Depth

Pressure in a fluid at rest is independent of the
shape of the container.
Pressure is the same at all points on a horizontal
plane in a given fluid.
ME33 : Fluid Flow
Scuba Diving and Hydrostatic Pressure
ME33 : Fluid Flow
Scuba Diving and Hydrostatic Pressure

Pressure on diver at
100 ft?
1m
kg
m
Pgage,2 gz 998 3 9.81 2 100 ft
m
s
3.28 ft
100 ft
Pabs ,2
1atm
298.5kPa
2.95atm
101.325
kPa
Pgage,2 Patm 2.95atm 1atm 3.95atm
Danger of emergency
ascent?
PV
1 1 PV
2 2
If you hold your breath on ascent, your lung
volume would increase by a factor of 4, which
would result in embolism and/or death.
ME33 : Fluid Flow
10
Boyles law
V1 P2 3.95atm

4
V2 P1
1atm
Pascals Law
Pressure applied to a
confined fluid increases
the pressure throughout
by the same amount.
In picture, pistons are at
same height:
F1 F2
F2 A2
P1 P2
A1 A2
F1 A1
Ratio A2/A1 is called ideal

mechanical advantage
ME33 : Fluid Flow
11
The Manometer
An elevation change of
Dz in a fluid at rest
corresponds to DP/g.
A device based on this is
called a manometer.
A manometer consists of
a U-tube containing one
or more fluids such as
mercury, water, alcohol,
or oil.
Heavy fluids such as
mercury are used if large
pressure differences are
anticipated.
P1 P2
P2 Patm gh
ME33 : Fluid Flow
12
Mutlifluid Manometer
For multi-fluid systems
Pressure change across a fluid
column of height h is DP = gh.
Pressure increases downward, and
decreases upward.
Two points at the same elevation in a
continuous fluid are at the same
pressure.
Pressure can be determined by
adding and subtracting gh terms.
P2 1 gh1 2 gh2 3 gh3 P1

ME33 : Fluid Flow
13
Measuring Pressure Drops

Manometers are well-suited to measure
pressure drops across
valves, pipes, heat
exchangers, etc.
Relation for pressure
drop P1-P2 is obtained by
starting at point 1 and
adding or subtracting gh
terms until we reach point
2.
If fluid in pipe is a gas,
2>>1 and P1-P2= gh
ME33 : Fluid Flow
14
The Barometer
Atmospheric pressure is
measured by a device called a
barometer; thus, atmospheric
pressure is often referred to as
the barometric pressure.
PC can be taken to be zero
since there is only Hg vapor
above point C, and it is very
low relative to Patm.
Change in atmospheric
pressure due to elevation has
many effects: Cooking, nose
bleeds, engine performance,
aircraft performance.
PC gh Patm
Patm gh
ME33 : Fluid Flow
15
Fluid Statics
Fluid Statics deals with problems associated
with fluids at rest.
In fluid statics, there is no relative motion
between adjacent fluid layers.
Therefore, there is no shear stress in the fluid
trying to deform it.
The only stress in fluid statics is normal stress
Normal stress is due to pressure
Variation of pressure is due only to the weight of the
fluid fluid statics is only relevant in presence of
gravity fields.
Applications: Floating or submerged bodies,

water dams and gates, liquid storage tanks, etc.
ME33 : Fluid Flow
16
Hoover Dam
ME33 : Fluid Flow
17
Hoover Dam
ME33 : Fluid Flow
18
Hoover Dam
Example of elevation
head z converted to
velocity head V2/2g.
We'll discuss this in
more detail in Chapter
5 (Bernoulli equation).
ME33 : Fluid Flow
19
Hydrostatic Forces on Plane Surfaces

On a plane surface, the
hydrostatic forces form a
system of parallel forces
For many applications,
magnitude and location of
application, which is
called center of
pressure, must be
determined.
Atmospheric pressure
Patm can be neglected
when it acts on both sides
of the surface.
ME33 : Fluid Flow
20
Resultant Force
The magnitude of FR acting on a plane surface of a

completely submerged plate in a homogenous fluid
is equal to the product of the pressure PC at the
centroid of the surface and the area A of the
surface
ME33 : Fluid Flow
21
Center of Pressure
Line of action of resultant force
FR=PCA does not pass through
the centroid of the surface. In
general, it lies underneath
where the pressure is higher.
Vertical location of Center of
Pressure is determined by
equation the moment of the
resultant force to the moment
of the distributedIpressure
force.y p yC xx ,C
yc A
$Ixx,C is tabulated for simple

geometries.
ME33 : Fluid Flow
22
Hydrostatic Forces on Curved Surfaces
FR on a curved surface is more involved since it

requires integration of the pressure forces that
change direction along the surface.
Easiest approach: determine horizontal and
vertical components FH and FV separately.
ME33 : Fluid Flow
23
Hydrostatic Forces on Curved Surfaces

Horizontal force component on curved surface:
FH=Fx. Line of action on vertical plane gives y
coordinate of center of pressure on curved
surface.
Vertical force component on curved surface:
FV=Fy+W, where W is the weight of the liquid in
the enclosed block W=gV. x coordinate of the
center of pressure is a combination of line of
action on horizontal plane (centroid of area) and
line of action through volume (centroid of
volume).
Magnitude of force FR=(FH2+FV2)1/2
Angle of force is a = tan-1(FV/FH)
ME33 : Fluid Flow
24
Buoyancy and Stability

Buoyancy is due to the fluid displaced by a
body. FB=fgV.
Archimedes principal : The buoyant
force acting on a body immersed in a fluid
is equal to the weight of the fluid displaced
by the body, and it acts upward through
the centroid of the displaced volume.
ME33 : Fluid Flow
25
Buoyancy and Stability

Buoyancy force FB is
equal only to the displaced
volume fgVdisplaced.
Three scenarios possible
1. body<fluid: Floating body
2. body=fluid: Neutrally buoyant
3. body>fluid: Sinking body
ME33 : Fluid Flow
26
Example: Galilean Thermometer

Galileo's thermometer is made of a sealed
glass cylinder containing a clear liquid.
Suspended in the liquid are a number of
weights, which are sealed glass containers
with colored liquid for an attractive effect.
As the liquid changes temperature it changes
density and the suspended weights rise and
fall to stay at the position where their density is
equal to that of the surrounding liquid.
If the weights differ by a very small amount and
ordered such that the least dense is at the top
and most dense at the bottom they can form a
temperature scale.
ME33 : Fluid Flow
27
Example: Floating Drydock

Auxiliary Floating Dry Dock Resolute
(AFDM-10) partially submerged
Submarine undergoing repair work on

board the AFDM-10
Using buoyancy, a submarine with a displacement of 6,000 tons can be lifted!
ME33 : Fluid Flow
28
Example: Submarine Buoyancy and Ballast
Submarines use both static and dynamic depth

control. Static control uses ballast tanks
between the pressure hull and the outer hull.
Dynamic control uses the bow and stern planes
to generate trim forces.
ME33 : Fluid Flow
29

SSN 711 nose down after accident
which damaged fore ballast tanks
Normal surface trim
ME33 : Fluid Flow
30
Damage to SSN 711

(USS San Francisco)
after running aground on
8 January 2005.
ME33 : Fluid Flow
31

Ballast Control Panel: Important station for controlling depth of submarine
ME33 : Fluid Flow
32
Stability of Immersed Bodies
Rotational stability of immersed bodies depends upon

relative location of center of gravity G and center of
buoyancy B.
G below B: stable
G above B: unstable
G coincides with B: neutrally stable.
ME33 : Fluid Flow
33
Stability of Floating Bodies

If body is bottom heavy
(G lower than B), it is
always stable.
Floating bodies can be
stable when G is higher
than B due to shift in
location of center
buoyancy and creation of
restoring moment.
Measure of stability is the
metacentric height GM. If
GM>1, ship is stable.
ME33 : Fluid Flow
34
Rigid-Body Motion
There are special cases where a body of fluid can undergo rigidbody motion: linear acceleration, and rotation of a cylindrical
container.
In these cases, no shear is developed.

Newton's 2nd law of motion can be used to derive an equation of
motion for a fluid that acts as a rigid body
P gk a
In Cartesian coordinates:
ME33 : Fluid Flow
P
P
P
ax ,
ay ,
g ax
x
y
z
35
Linear Acceleration
Container is moving on a straight path
ax 0, a y az 0
P
P
P
ax ,
0,
g
x
y
z
Total differential of P
dP ax dx gdz
Pressure difference between 2 points

P2 P1 ax x2 x1 g z2 z1
Find the rise by selecting 2 points on

free surface P2 = P1
a
Dzs zs 2 zs1 x x2 x1
g
ME33 : Fluid Flow
36
Rotation in a Cylindrical Container

Container is rotating about the z-axis
ar r 2 , a az 0
P
P
P
r 2 ,
0,
g
r
Total differential of P
dP r 2 dr gdz
On an isobar, dP = 0
dzisobar r 2
2 2
zisobar
r C1
dr
g
2g
Equation of the free

surface
2
zs h0
ME33 : Fluid Flow
37
4g
2r 2
Examples of Archimedes Principle
The Golden Crown of Hiero II, King of

Syracuse
Archimedes, 287-212 B.C.
Hiero, 306-215 B.C.
Hiero learned of a rumor where
the goldsmith replaced some of
the gold in his crown with silver.
Hiero asked Archimedes to
determine whether the crown was
pure gold.
Archimedes had to develop a
nondestructive testing method
ME33 : Fluid Flow
39
The Golden Crown of Hiero II, King of

Syracuse
The weight of the crown and
nugget are the same in air: Wc =
cVc = Wn = nVn.
If the crown is pure gold, c=n
which means that the volumes
must be the same, Vc=Vn.
In water, the buoyancy force is
B=H2OV.
If the scale becomes unbalanced,
this implies that the Vc Vn,
which in turn means that the c
Goldsmith was shown to be a

fraud!
ME33 : Fluid Flow
40
Hydrostatic Bodyfat Testing

What is the best way to
measure body fat?
Hydrostatic Bodyfat Testing
using Archimedes Principle!
Process
Measure body weight
W=bodyV
Get in tank, expel all air, and
measure apparent weight Wa
Buoyancy force B = W-Wa =
H2OV. This permits
computation of body volume.
Body density can be
computed body=W/V.
Body fat can be computed
from formulas.
ME33 : Fluid Flow
41
Hydrostatic Bodyfat Testing in Air?

Same methodology as
Hydrostatic testing in water.
What are the ramifications of
using air?
Density of air is 1/1000th of
water.
Temperature dependence of
air.
Measurement of small volumes.
Used by NCAA Wrestling (there
is a BodPod on PSU campus).
ME33 : Fluid Flow
42

Chapter 3: Pressure and Fluid Statics: Eric G. Paterson

Uploaded by

Copyright:

Available Formats

Chapter 3: Pressure and Fluid Statics: Eric G. Paterson

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 3: Pressure and Fluid Statics: Eric G. Paterson

Uploaded by

Copyright:

Available Formats

Chapter 3: Pressure and Fluid Statics

ME33 : Fluid Flow