16 Major Losses

16 Major Losses
16 Major Losses
1. Equipment failure loss
2. Set up & adjustment loss
3. Cutting tool and jig change loss
4. Start up loss
5. Minor Stoppage and idling loss EQUIPMENT LOSSES
6. Reduced speed loss
7. Defects &rework loss
8. Shutdown loss
9. Management loss
10. Operating motion loss
11. Line organization loss MANPOWER LOSSES
12. Logistics / Distribution loss
13. Measurement and adjustment loss
14. Energy Loss
15. Die, Tool and Jig loss MATERIAL & ENERGY LOSS
16. Yield loss
EQUIPMENT LOSS
Losses that impede equipment efficiency
Equipment Failure Loss
The equipment breaks down causing the function of the line or process
to stop. Often this is considered as a sporadic failure, typically caused by
equipment component failure.
Examples: Bearing failure due to wear, electrical fault, snapped belt.
* There is flexibility on where to set the threshold between equipment failure (an Availability Loss) and a minor
stop (a Performance Loss). For example, your policy might be that any down time longer than two minutes
should have a reason associated with it – and thus shall be considered equipment failure.
Set-up & Adjustment Loss
This loss occurs during a changeover between products. Set up time is
defined as the amount of time taken to change a process over from the
last part of a production run to the first good, repeatable part of the
next production run.
Adjustment within the set up time is often hidden, and involves

tweaking settings until optimal run conditions are achieved.
Examples: Changing products, changing packaging, adjusting the feed rate.
* The largest source of Setup and Adjustment time is typically changeovers (also referred to as make ready or
setup), which can be addressed through a SMED (Single-Minute Exchange of Dies) program.
Cutting Tool and Jig Change Loss
The time loss incurred swapping any consumable tooling item when it
has become worn/ineffective or damaged.
Examples: Time spent replacing saw blades, cutting/grinding tools, and lathe tools.
Start-up Loss
The loss incurred whilst starting up equipment, to get to steady state
operating conditions, after planned or unplanned shutdown.
Examples: Time spent warming/cooling equipment to operating temperature,

compressor/hydraulic power pack run-up time.
Minor Stoppage & Idling Loss
These are typically small stoppages not logged as breakdowns and
issues causing the machine to pause or idle for short periods. They are
often chronic losses, regularly repeated, often not recorded and usually
less than 1 or 2 minutes duration and resolved by the operator
Examples: Waiting for a machine to index, emptying a mould during press operation,
a sensor fault or product blockage.
Reduced Speed Loss
This loss occurs from operating at a speed less than the design speed.
Examples: dirty or worn out equipment, poor lubrication, substandard materials,

poor environmental conditions and operator inexperience.
Defect & Rework Loss
This is the loss of defective product i.e. Not Right First Time which
requires rework, repair or scrap.
Examples: Out of spec product, low weight product requiring top-up, poor surface
finish, incorrect labelling.
Shutdown Loss
The loss incurred by deliberately shutting down the equipment within
the production plan.
Examples: Routine maintenance, periodic overhaul, cleaning, statutory inspections.

MANPOWER LOSSES
Losses that impede human work efficiency
Management Loss
These are waiting time losses generated by management problems.
Examples: Failure to provide materials, spare parts, manpower resource, utilities,

work instructions.
Operating Motion Loss
Losses are created due to unnecessary/excessive operator movement
and transportation, as a result of poor layout and work organization.
Examples: Walking loss, wasted motion e.g. unnecessary reaching and lifting.
Line Organization Loss
This loss results from a shortage of operators on the line and operators
having to work on more equipment than was originally planned.
Examples: No additional cover or contingency for break times, training and time
spent off the line.
Logistics / Distribution Loss
This loss is the wasted time that is experienced in the incorrect or
inefficient delivery of raw materials, packaging or products to and from
the factory or the production line.
Examples: Incorrect delivery of materials from supplier to store, late deliveries,

excessive handling of deliveries (double handling).
Measurement and Adjustment Loss
This loss is caused by the frequent measurement and adjustment to
prevent the recurrence of problems.
Examples: Excessive inspection integrated in the process as a result of poor quality

and failure to find root cause. Adjustment loss is experienced when adjusting
equipment back to the standard after routine cleaning and periodic consumable
changes (e.g. labels, film, and ink).
MATERIAL & ENERGY LOSS
Losses that impede effective use of production resources
Energy Loss
Energy loss is the input energy which cannot be used effectively for
processing.
Examples: Start-up losses, Idling losses, leakage of fuel / air / oil.

Die, Tool and Jig Loss
This is the cost of the physical consumption of the spare parts or the
refurbishment/maintenance of items that are used on the line.
Examples: Lose of tool due to regrinding, poor life of molds etc, repairs of Dies/
Tools.
Yield Loss
This is the total loss between the input of raw material and the output
of finished goods.
Examples: Over-pack, giveaway, mass balances, excess material stock/ weight.

THANK YOU

16 Major Losses

Uploaded by

Copyright:

Available Formats

16 Major Losses

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

16 Major Losses

Uploaded by

Copyright:

Available Formats

What are the different types of equipment losses mentioned?

What are the different types of manpower losses mentioned?

16 Major Losses

Examples: Bearing failure due to wear, electrical fault, snapped belt.

Adjustment within the set up time is often hidden, and involves

Examples: Time spent warming/cooling equipment to operating temperature,

Examples: dirty or worn out equipment, poor lubrication, substandard materials,

Examples: Routine maintenance, periodic overhaul, cleaning, statutory inspections.

Examples: Failure to provide materials, spare parts, manpower resource, utilities,

Examples: Incorrect delivery of materials from supplier to store, late deliveries,

Examples: Excessive inspection integrated in the process as a result of poor quality

Examples: Start-up losses, Idling losses, leakage of fuel / air / oil.

Examples: Over-pack, giveaway, mass balances, excess material stock/ weight.

You might also like