210 MW Boiler

210 MW Boiler
D M Naphade
Dy Ex.Engineer
• 210 MW Boiler
Trainee should able to tell type with working
& specification of boiler
INTRODUCTION :
ENERGY CONVERSION IN A T.P.S.
Thermal Power Station works on ‘Rankine Cycle’
Components of TPS:
1. Boiler 2. Steam Turbine
3. Condenser 4. Pump.
& the Generator
BOILING PROCESS:
Nucleate Boiling :As the saturation temperature is reached, Bubbles of Vapors are
formed, they rise up and condense. As the temperature of the heating surface is
increased the bubbles formed finally reach the surface & escape and surrounding
water particles come down to take up the space of the bubbles.This is nucleate
boiling.
FILM BOILING:
As the heat transfer through the heating surface is increased we can reach to a
point where individual bubbles are no longer formed and instead the entire heat
transfer surface gets a layer of steam formed as the bubbles coalesce .
The water particles are no longer coming down to wet the heating surface
Due to this the heating surface can get over heated this is undesirable.
210 MW BOILER TECHNICAL SPECIFICATIONS :
Function of the boiler is to generate
steam at specified pressure &
temperature.
TYPE :
Conventional, Single Drum, Tangentially fired,
Balanced draught, Natural Circulation, Radiant
Reheat Type, Dry Bottomwith Direct Fired
Pulverized Coal with Bowl Mill or with Fuel Oil.
FUEL : Coal : Bituminous :

Designed Coal
Fixed Carbon 37.3 %
Volatile Matter 27.6 %
Moisture 10 %
Ash 25 %
Grind ability 50 HGI
HHV 5000 Kcal / Kg
210 MW BOILER TECHNICAL SPECIFICATIONS :
GENERAL INFORMATION
HEATING SURFACE
•TOTAL HEATING SURFACE:- 22862.10 SQ.M
•WATER WALL:- 2274 SQ.M
•ECONOMISER:- 5687.71 SQ.M
•SUPERHEATER:- 12252.73 SQ.M
•Re-HEATER:-2.647.66 SQ.M
Tube diametersRange from
FURNACE :
44.5 mm to 63.5 mm with
Width 13.868 Metre.
Thickness min. 3.4 mm for RH
Depth 10.592 Metre.
3.6 for for Eco & 4mm for SH
Volume 5494 M3
Type Fusion Welded Panels
Fuel Oil : (IS 1593 )

Carbon – 85.5 %
Hydrogen – 11.05 %
Sulphur – 2.5 %
Others – 0.5 %
GCV – 10,200 Kcal / Kg.
Warm up and Ignitor Oil : LDO for warm up
210 MW BOILER Pressure Parts
Boiler Drum Click to see the
length : 15.7m W/walls construction
Internal Diameter :1976mm
Thickness :132mm
Material : Special carbon steel plate of SA 299 A
Height :52m
Down comers
Total =8
Front Side =2 6 down comers OD 406mm
Rear Side =2 Thickness 32 mm
Left Side =1
Right side=1
Platen water wall header=4Nos. OD 324 mm,
thickness=25 mm
Ring Header=323 mm OD thickness=45 mm

Water wall
Material used :Seamless steel tube of SA 210
ID : 63.5mm
Thickness 6.3mm
Membrane Panel - Formed by welding 22 tubes
Total panel = 83
Water wall
Material used :Seamless steel tube of SA 210
ID : 63.5mm
Thickness 6.3mm
Membrane Panel - Formed by welding 22 tubes
Total panel = 83
LHS TOP
RISER
HEADER
LOCATED
IN PENT
HOUSE
LEFT WATER
WALL
LHS
BRH
The superheated steam system has mainly
three sections. The low temperature
superheater section(arranged in the second
pass of the, unit), the radiant platen
superheater (arranged at the outlet section of
the furnace) and the final superheater
(arranged after the reheater). Two number
superheater desuperheaters have been
provided in between the LTSH and the platen
superheater for controlling the superheated
steam temperature. The complete second
pass of the boiler(upto the economiser) has
been covered with the steam cooled
superheater wall sections.
Main HRH Lines CRH Feed water
steam LINES line
Pipe size Ø 323.8 Ø 406 Ø 457 Ø 323.8

mm x mm x 16 mmx mm x 35
Lines 41.5 16
No. of 02 02 02 01
Materials used for the boiler tubes as per ASME
Material ASTM Grade Tempera

Specific ture
ation
Carbon Steel SA 210 A1 450oC
Carbon ¼ % MO SA-209 T1 480oC
Steel
1 % Cr, ½ % MO SA-213 T11 550oC
Steel
2 ½ % Cr, 1 % MO SA-213 T22 580oC
Steel
18%
Note: Cr,Materials
The SA-213
8 % Ni are selected afterT304 Upto
finding out the mid
Stainless
wall Steelas well as the outer surfacetemperature
temperature 700oC
for each and every super heater & re heater circuit
18% Cr, 8 % Ni SA-213 T347 Upto
Stainless Steel 700oC
SAFETY VALVES :
Note: The pressure settings are slightly different in different locations/Units
Sl. Location Make Set Reliving

No. Dresser Pressure Capacity
Type ksc (g) T / Hr.
1. Drum 1759 WA 158.2 159
1749 WA 161 193
1749 WA 162.4 195
2. Super Heater 1538 VX 141.5 87.0
(Electromatic Relief Valve) 1739 WD 144.5 87.0
1739 WD 143.8 86.0
3. Re Heater (CRH) 1775 WA 33.0 100.0
1785 WA 33.4 130.3
1785 WA 33.8 131.6
1785 WA 34.1 133.0
4. Re Heater (HRH) 1705 RWD 30.6 115
Boiler Drum
length : 15.7m
Internal Diameter
:1976mm
Thickness :132mm
Material : Special
carbon steel plate
of SA 299 A
ANY QUESTION PLEASE?

210 MW Boiler

Uploaded by

Copyright:

Available Formats

210 MW Boiler

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

210 MW Boiler

Uploaded by

Copyright:

Available Formats

210 MW Boiler

FUEL : Coal : Bituminous :

Fuel Oil : (IS 1593 )

Ring Header=323 mm OD thickness=45 mm

Pipe size Ø 323.8 Ø 406 Ø 457 Ø 323.8

Material ASTM Grade Tempera

Sl. Location Make Set Reliving

You might also like