DATA RATE LIMITS

Course Code: COE 3201 Course Title: Data Communication

Dept. of Computer Engineering

Faculty of Engineering

Lecture No: 4 Week No: 4 Semester: Spring 19-20

Lecturer: Tanjil Amin (tanjil@aiub.edu)
Lecture Outline

1. Information as Digital Signal

2. Transmission of Digital Signals
3. Bit Rate
4. Data Rate
5. Nyquist Bit Rate
6. Shannon Capacity
7. Network Performance
Information as Digital Signal
 
Information can also be represented by a
digital signal
For example, a 1 can be encoded as a
positive voltage and a 0 as zero voltage
A digital signal can have more than two
levels
In this case, we can send more than 1 bit
for each level
In general, if a signal has L levels, each
level needs L bits. For this reason, we can
send = 2 bits in (b)
Transmission of Digital Signals
 let us consider a nonperiodic digital signal, similar to the ones we encounter in
data communications
 The fundamental question is, How can we send a digital signal from point A to
point B?
 We can transmit a digital signal by using

baseband transmission
broadband transmission
 Both baseband and broadband describe how data
is transmitted between two nodes.
 Baseband technology transmits a single data
signal/stream/channel at a time while broadband
technology transmits multiple data
signals/streams/channels simultaneously at the
same time.
Differences Between Baseband and
Broadband Transmissions
Baseband transmission Broadband transmission
Transmit digital signals Transmit analog signals
To boost signal strength, use repeaters To boost signal strength, use amplifiers
Can transmit only a single data stream at Can transmit multiple signal waves at a
a time time
Support bidirectional communication Support unidirectional communication
simultaneously only
Support TDM based multiplexing Support FDM based multiplexing
Use coaxial, twisted-pair, and fiber-optic Use radio waves, coaxial cables, and fiber
cables optic cables
Mainly used in Ethernet LAN networks Cable TV, Wi-Fi, and Power Line
communication are some examples
Bit Rate
Most digital signals are nonperiodic, and thus period and frequency are not
appropriate characteristics
To describe digital signals another term—bit rate (instead of frequency)
Bit rate is the number of bits sent in 1s
Expressed in bits per second (bps)

Example: Assume we need to download text documents at the rate of 100

pages per second. What is the required bit rate of the channel?
Data Rate
Factors Impacting Data Rate

An important consideration in data communications is how

fast we can send data, in bits per second over a channel.
Data rate depends on three factors:

1. The bandwidth available

2. The level of the signals we use
3. The quality of the channel (the level of noise)
Formulas to Calculate Data Rate

Two theoretical formulas were developed to calculate the data

rate:

1. Nyquist Bit Rate for a noiseless channel.

2. Shannon Capacity for a noisy channel.
Noiseless Channel: Nyquist Bit Rate

 Fora noiseless channel, the Nyquist bit rate formula defines

the theoretical maximum bit rate

Here,
BR = Bit Rate in bps
BW = Bandwidth of the channel in Hz
L = Number of levels representing data
Noiseless Channel: Nyquist Bit Rate
 From the formula it seems like, given a specific bandwidth, we
can have any bit rate we want by increasing number of levels.
The idea is theoretically correct, but practically there is a limit.

 By increasing number of levels, we impose a burden on the

receiver. If the number of levels in a signal is just 2, the receiver
can easily distinguish between a 0 and a 1.

 If the level of a signal is 64, the receiver must be very

sophisticated to distinguish between 64 different levels. So,
increasing the levels of a signal reduces the reliability of the
system.
Noiseless Channel: Nyquist Bit Rate

 Problem: Consider a noiseless channel with a bandwidth of 3000

Hz transmitting a signal with two signal levels. What can be the
maximum bit rate?
Solution:

bps
Noiseless Channel: Nyquist Bit Rate

 Problem:We need to send 265 kbps over a noiseless channel with

a bandwidth of 20 kHz. How many signal levels do we need?

Solution:

Levels
Noisy Channel: Shannon Capacity
 We cannot have a noiseless channel really. The channel is always
noisy. Theoretical highest data rate for a noisy channel can be
calculated using Shannon capacity formula:

Here,
C = Capacity in bps
BW = Bandwidth of the channel in Hz
SNR = Signal-to­noise ratio

***Shannon formula does not have any signal level, which means that no matter how
many levels we have, we cannot achieve a data rate higher than the capacity of the
channel.
Noisy Channel: Shannon Capacity

 Problem: Consider an extremely noisy channel in which the value

of the signal-to-noise ratio is almost zero. In other words, the noise
is so strong that the signal is faint. What is the capacity of the
channel?

Solution:

***This means that the capacity of this channel is zero regardless

of the bandwidth. In other words, we cannot receive any data
through this channel if SNR is zero.
Noisy Channel: Shannon Capacity

 Problem: We have a channel with a 1-MHz bandwidth. The SNR

for this channel is 63. What is the maximum bit rate That can be
achieved in this channel?

Solution:
Maximum bit rate of a channel is its capacity. Using Shannon’s
formula

Mbps
Using Both Limits
Example

In practice, we need to use both methods to find the limits and

signal levels.
Problem: We have a channel with a 1-MHz bandwidth. The SNR
for this channel is 63. What are the appro­priate bit rate and signal
level?
Solution:
From previous example we know capacity of the channel is 6
Mbps. This is the upper limit. For better performance we choose
something lower, 4 Mbps, for example. Then using Nyquist
formula we can find the number of signal levels.
Using Both Limits

 Continued from previous slide here…

Then using Nyquist formula we can find the number of signal

levels.

Levels

The Shannon capacity gives us the upper limit and the Nyquist
formula tells us how many signal levels we need.
Network Performance
Quality of Service (QoS) Parameters

The Internet and its underlying local area and wide area networks
must include a QoS capability to provide various levels of service
to different types of application traffic. A QoS capability can deal
with priority, delay constraints, delay variability constraints, and
other similar requirements. Some common parameters
determining the quality of network performance are:
 Bandwidth
 Throughput
 Latency or Delay
 Bandwidth-Delay Product
 Bandwidth
One characteristic that measures network performance is bandwidth. However,
the term can be used in two different contexts with two different measuring
values: bandwidth in hertz and bandwidth in bits per second.

 Bandwidth in Hertz: Bandwidth in hertz is the range of frequencies con­

tained in a composite signal or the range of frequencies a channel can
pass. For exam­ple, we can say the bandwidth of a subscriber telephone
line is 4 kHz.

 Bandwidth in Bits per Seconds: The term bandwidth can also refer to the
number of bits per second that a channel, a link, or even a network can
transmit. For example, one can say the bandwidth of a Fast Ethernet
network (or the links in this network) is a maximum of 100 Mbps.
Bandwidth

Example 1:
The bandwidth of a subscriber line is 4 kHz for voice or data. The
bandwidth of this line for data trans­ mission can be up to 56,000
bps using a sophisticated modem to change the digital signal to
analog.

Example 2:
If the telephone company improves the quality of the line and
increases the bandwidth to 8 kHz, we can send 112,000 bps by
using the same technology as mentioned in Example 1.
 Throughput

 Throughput is a measure of how fast we actually can send data through a

network.

 At first glance, bandwidth in bits per second and throughput seem the same,
they are different.

 A link may have a bandwidth of B bps, but we can only send T bps through
this link with T always less than B.

 In other words, the bandwidth is a potential measurement of a link; the

throughput is an actual measurement of how fast we can send data.
Throughput

Example 1:
Imagine a highway designed to transmit 1000 cars per minute
from one point to another. However, if there is congestion on the
road, this figure may be reduced to 100 cars per minute. The
bandwidth is 1000 cars per minute; the throughput is 100 cars
per minute.

Example 2:
We may have a link with a bandwidth of 1 Mbps, but the devices
connected to the end of the link may handle only 200 kbps. This
means that we cannot send more than 200 kbps through this link.
Throughput

 Problem: A network with bandwidth of 10 Mbps can pass only

an average of 12,000 frames per minute with each frame
carrying an average of 10,000 bits. What is the throughput of
this network?

Solution:

Throughput Mbps
Latency or Delay

The latency or delay defines how long it takes for an entire

message to completely arrive at the destination from the time the
first bit is sent out from the source. We can say that latency is
made of four components: propagation time, transmission time,
queuing time and processing delay.

Latency = propagation time + transmission time + queuing time +

processing delay
Bandwidth-Delay Product

Bandwidth and delay are two performance metrics of a link.

However, a very important performance metrics in data
communications is the product of the two, the bandwidth-delay
product. We will elaborate on this issue, using two hypothetical
cases as examples in next slides.
Case 1
Case 2
Case Study Outcome

Looking at case 1, we can say that this product 1 x 5 or 5 is the

maximum number of bits that can fill the link. There can be no
more than 5 bits at any time on the link.

Looking at case 2, we can say that this product 5 x 5 or 25 is the

maximum number of bits that can fill the link. There can be no
more than 25 bits at any time on the link.

The bandwidth-delay product defines the number of bits that

can fill the link.
Books

1. Forouzan, B. A. "Data Communication and Networking. Tata McGraw." (2005).

References

1. Prakash C. Gupta, “Data communications”, Prentice Hall India Pvt.

2. William Stallings, "Data and Computer Communications”, Pearson
3. Forouzan, B. A. "Data Communication and Networking. Tata McGraw." (2005).