Thermodynamics: An Engineering Approach

Seventh Edition in SI Units

Yunus A. Cengel, Michael A. Boles
McGraw-Hill, 2011

Chapter 3
PROPERTIES OF PURE
SUBSTANCES

Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
PURE SUBSTANCE
• Pure substance: A substance that has a fixed chemical
composition throughout.
• Air is a mixture of several gases, but it is considered to be a
pure substance.

2
PHASES OF A PURE SUBSTANCE

The molecules
in a solid are
kept at their
positions by the
large springlike
inter-molecular
forces.
In a solid, the
attractive and
repulsive forces
between the
molecules tend
to maintain them
at relatively
constant
distances from
each other.

3
PHASE-CHANGE PROCESSES OF PURE
SUBSTANCES
• Compressed liquid (subcooled liquid): A substance that it is not
about to vaporize.
• Saturated liquid: A liquid that is about to vaporize.

At 1 atm and 20°C,

water exists in the
liquid phase
(compressed
liquid).

At 1 atm pressure
and 100°C, water
exists as a liquid
that is ready to
vaporize
(saturated liquid).
4
• Saturated vapor: A vapor that is about to condense.
• Saturated liquid–vapor mixture: The state at which the liquid and
vapor phases coexist in equilibrium.
• Superheated vapor: A vapor that is not about to condense (i.e., not a
saturated vapor).

At 1 atm pressure, the As more heat is

As more heat is transferred, temperature remains transferred, the
part of the saturated liquid constant at 100°C until the temperature of the
vaporizes (saturated liquid– last drop of liquid is vaporized vapor starts to rise
vapor mixture). (saturated vapor). (superheated vapor).
5
If the entire process between state 1 and 5 described in the figure is
reversed by cooling the water while maintaining the pressure at the
same value, the water will go back to state 1, retracing the same path,
and in so doing, the amount of heat released will exactly match the
amount of heat added during the heating process.

T-v diagram for the

heating process of
water at constant
pressure.
6
Saturation Temperature and Saturation Pressure
• The temperature at which water starts boiling depends on the pressure;
therefore, if the pressure is fixed, so is the boiling temperature.
• Water boils at 100C at 1 atm pressure.
• Saturation temperature Tsat: The temperature at which a pure substance
changes phase at a given pressure.
• Saturation pressure Psat: The pressure at which a pure substance changes
phase at a given temperature.

The liquid–vapor
saturation curve
of a pure
substance
(numerical
values are for
water).
7
• Latent heat: The amount of energy
absorbed or released during a phase-
change process.
• Latent heat of fusion: The amount of
energy absorbed during melting. It is
equivalent to the amount of energy
released during freezing.
• Latent heat of vaporization: The amount
of energy absorbed during vaporization
and it is equivalent to the energy released
during condensation.
• The magnitudes of the latent heats
depend on the temperature or pressure at
which the phase change occurs.
• At 1 atm pressure, the latent heat of
fusion of water is 333.7 kJ/kg and the
latent heat of vaporization is 2256.5 kJ/kg.
• The atmospheric pressure, and thus the
boiling temperature of water, decreases
with elevation.
8
Some Consequences of
Tsat and Psat Dependence
The variation of
the temperature
of fruits and
vegetables with
pressure during
vacuum cooling
from 25°C to 0°C.

In 1775, ice was made

by evacuating the air
space in a water tank. 9
PROPERTY DIAGRAMS FOR PHASE-CHANGE
PROCESSES
The variations of properties during phase-change processes are best studied
and understood with the help of property diagrams such as the T-v, P-v, and P-T
diagrams for pure substances.

T-v diagram of
constant-pressure
phase-change
processes of a pure
substance at various
pressures
(numerical values
are for water). 10
• saturated liquid line
• saturated vapor line
• compressed liquid region
• superheated vapor region
• saturated liquid–vapor
mixture region (wet region)

At supercritical
Critical point: The point
pressures (P > Pcr),
at which the saturated
there is no distinct liquid and saturated vapor
phase-change states are identical.
(boiling) process. 11
12
Extending the For water,
Diagrams to Include Ttp = 0.01°C
Ptp = 0.6117 kPa
the Solid Phase
At triple-point pressure
and temperature, a
substance exists in three
phases in equilibrium.

13
14
Sublimation: Phase Diagram
Passing from the
solid phase directly
into the vapor phase.

At low pressures
(below the triple-point
value), solids
evaporate without
P-T diagram of pure substances.
melting first
(sublimation).
15
The P-v-T surfaces present a great deal of information at once, but in a
thermodynamic analysis it is more convenient to work with two-dimensional
diagrams, such as the P-v and T-v diagrams.

16
 PROPERTY TABLES
• For most substances, the relationships among thermodynamic properties are too
complex to be expressed by simple equations.
• Therefore, properties are frequently presented in the form of tables.
• Some thermodynamic properties can be measured easily, but others cannot and
are calculated by using the relations between them and measurable properties.
• The results of these measurements and calculations are presented in tables in a
convenient format.
Enthalpy—A Combination Property

The
combination
u + Pv is
frequently
encountered
in the analysis The product pressure 
of control volume has energy units.
volumes. 17
 Saturated Liquid and Saturated Vapor States
• Table A–4: Saturation properties of water under temperature.
• Table A–5: Saturation properties of water under pressure.

A partial list of Table A–4.

Enthalpy of vaporization, hfg (Latent

heat of vaporization): The amount of
energy needed to vaporize a unit mass
of saturated liquid at a given
temperature or pressure.

18
19
20
Examples:
Saturated liquid
and saturated
vapor states of
water on T-v and
P-v diagrams.

21
22
Saturated Liquid–Vapor Mixture
Quality, x : The ratio of the mass of vapor to the total mass of the mixture.
Quality is between 0 and 1 0: sat. liquid, 1: sat. vapor.
The properties of the saturated liquid are the same whether it exists alone or in
a mixture with saturated vapor.
Temperature and
pressure are dependent
properties for a mixture.

The relative
amounts of
liquid and
vapor phases
in a saturated
mixture are A two-phase system can be
specified by treated as a homogeneous
the quality x. mixture for convenience.
23
y v, u, or h.

24
25
26
In the region to the right of the Superheated Vapor
saturated vapor line and at
temperatures above the critical Compared to saturated vapor,
point temperature, a substance superheated vapor is characterized by
exists as superheated vapor.
In this region, temperature and
pressure are independent
properties.

At a specified
P, superheated
vapor exists at
a higher h than
the saturated
vapor.

A partial
listing of
Table A–6. 27
28
The compressed liquid properties Compressed Liquid
depend on temperature much more Compressed liquid is characterized by
strongly than they do on pressure.
y  v, u, or h

A more accurate relation for h

A compressed liquid
may be approximated
as a saturated liquid at
the given temperature.

29
30
 Reference State and Reference Values
• The values of u, h, and s cannot be measured directly, and they are calculated from
measurable properties using the relations between properties.
• However, those relations give the changes in properties, not the values of properties at
specified states.
• Therefore, we need to choose a convenient reference state and assign a value of zero for
a convenient property or properties at that state.
• The reference state for water is 0.01°C and for R-134a is -40°C in tables.
• Some properties may have negative values as a result of the reference state chosen.
• Sometimes different tables list different values for some properties at the same state as a
result of using a different reference state.
• However, In thermodynamics we are concerned with the changes in properties, and the
reference state chosen is of no consequence in calculations.

31
32
33
THE IDEAL-GAS EQUATION OF STATE
• Equation of state: Any equation that relates the pressure, temperature,
and specific volume of a substance.
• The simplest and best-known equation of state for substances in the gas
phase is the ideal-gas equation of state. This equation predicts the P-v-T
behavior of a gas quite accurately within some properly selected region.
Ideal gas equation
of state

R: gas constant
M: molar mass (kg/kmol)
Ru: universal gas constant

Different substances have different

gas constants.
34
Mass = Molar mass  Mole number Ideal gas equation at two
states for a fixed mass

Various expressions
of ideal gas equation

Real gases behave as an ideal gas at low

densities (i.e., low pressure, high temperature).

Properties per unit mole are

denoted with a bar on the top. 35
36
Is Water Vapor an Ideal Gas?
• At pressures below 10 kPa, water
vapor can be treated as an ideal
gas, regardless of its temperature,
with negligible error (less than 0.1
percent).
• At higher pressures, however, the
ideal gas assumption yields
unacceptable errors, particularly in
the vicinity of the critical point and
the saturated vapor line.
• In air-conditioning applications, the
water vapor in the air can be
treated as an ideal gas. Why?
• In steam power plant applications,
however, the pressures involved
are usually very high; therefore,
ideal-gas relations should not be
used.

Percentage of error ([|vtable - videal|/vtable] 100) involved in assuming

steam to be an ideal gas, and the region where steam can be
treated as an ideal gas with less than 1 percent error. 37
38
39
Assignment No. 2

40