Test

TEST NO.
21
1. Fast process of analyzing all elements and a chemical
components of steel casting is
a. Pyrometer
b. Carbon analyzer
c. Wet analyzer
d. Spectrometer
2. Which of the following is not a kind of mandrel?
a. Expanded
b. Extended
c. Contraction
d. Taper
3. A cutting tool angle between the side cutting edge and the plane
perpendicular to direction of feed travel is _____ angle.
a. Side relief
b. Side cutting edge
c. Lead
d. Side rake
4. A section in a machine shop operation is called
a. Core making
b. Machining
c. Fitting
d. Pattern
5. The tool bit made of tool blank consists of face, nose, shank and
_______.
a. Cutting edge
b. None of these
c. Round nose
d. Nose
6. The cutting tool used the shaper are similar to turning tools of
________ machine.
a. Planer
b. Broaching
c. Boring
d. Lathe
7. The blades for hacksaw have number of teeth range of
a. 15 – 38 teeth
b. 14 – 32 teeth
c. 12 – 30 teeth
d. 12 – 32 teeth
8. __________ no part of the headstock.
a. Back gear
b. Spindle
c. Anvil
d. Motor
9. _____ is a lathe carriage part that bridge across the bed to
carry the cross slide and tool rest.
a. Automatic feed
b. Apron
c. Compound rest
d. Saddle
10. What is the recommended cutting speed range for bronze in
fpm
a. 60 / 70
b. 200 / 250
c. 80 / 60
d. 100 / 110
11. For ordinary turning drilling and milling on low strength steel the
cutting fluid applied have soluble oil with consistency of 1 part oil to
_____ parts water.
a. 10 to 30
b. 10
c. 5 to 10
d. 10 to 20
12. The five principal parts of the shaper are the table, tool
slide, base, ram and
a. Column
b. Vise
c. Drive motor
d. Apron
13. In drilling soft material use cutting angle as low as 40
degrees but for extremely hard material up to _____ degrees is
recommended.
a. 80
b. 65
c. 75
d. 70
14. An act of cutting out a piece of material at a desired shape and
size
a. Broaching
b. Blanking
c. Slitting
d. Dinking
15. A research agency handling assistance to all foundry, machine
shop and metallurgical plant operation.
a. MIRDC
b. BOI
c. DOST
d. All of these
16. Web is a part of a drill and is usually thicker _____.
a. Beside the land
b. Nearing the shank
c. Close to the future
d. At the tip portion

17. It is a symbol _____ that the work surfaces should be
machined finished and placed on the line that represents the
surface to be machined.
a. f
b. 5
c. 20
d. F. A. O.
18. Safety features that must be placed and maintained at
machine, black smith welding and foundry shops called
a. Walkway shops
b. Safety notices
c. Safety goggles
d. Safety notices in markers / boards

19. It is axially located rectangular groove in a hub and shaft
a. Key seat
b. Cotter pin set
c. Flute
d. Set screw point

20. In a cutting tool the cutting end can also be generally called
a. End cutting edge
b. Nose
c. Back rake
d. Side rake
21. What factors can modify the recommended cutting speed of
known work piece?
a. Rough cutting of work piece
b. Modify the shape of the cutting tools
c. Use correctly shape of the cutting tools
d. Depth of cut
22. A machine shop equipment that can filter horizontally,
vertically or angular plane called
a. Shaper machine
b. Welding machine
c. Drill machine
d. Power saw
23. It is petroleum by product used as electrodes in an electric arc
furnace melting operation.
a. Anthracite coke
b. Foundry coke
c. Graphite electrodes
d. Bituminous coke
24. Which of the following is an unsafe condition in operating
machine?
a. Wearing denim pants / safety shoes
b. Wearing a canvass apron
c. Operating with safety gloves
d. Wearing safety goggles / heating aid

25. Relief angle of single point cutting mild steel cast iron and other
average work as recommended should be in the range of _____
degrees for high speed tools.
a. 8 to 12
b. 10 to 5
c. 5 to 7
d. 12 to 16
26. Tap not used for cutting thread _____.
a. Tapping tap
b. Bottoming tap
c. Plugging tap
d. Taper tap
27. Which of the following tools does not belong to the group?
a. Hermaphrodite caliper
b. Divider
c. Double VEE block
d. Trammel
28. In machine shop had forging operation of lengthening a piece of
work while reducing the cross sectional area of work is called
a. Bloating
b. Upsetting
c. Spreading
d. Draining
29. Which of the following services is not considered to be a work
of a machinist?
a. Reboring
b. Grinding
c. Over hauling
d. Honing
30. Type of chuck wherein the work of piece with standard diameter
or size could be attached fast and quick specially small size work of
mass production called
a. Lathe drive plate
b. Clamp toe dog
c. Collet attachment
d. Steady center rest

31. This particular cutting tool material could stand cutting
temperature of 1800 °F and higher at cutting speed beyond those
possible with other cutting tool materials called
a. Titanium carbide
b. Ceramic
c. Carbide grade
d. Cubic boron nitride

32. Common defects encountered in the foundry shop steel casting
operation and also in welding practices.
a. Cracks
b. Cold shot
c. Parting line
d. Blow / pin holes

33. Lathe operator to remove the taper shank from the taper hole
uses drift. It is also called
a. Tong
b. Morse taper
c. Chuck taper
d. Pyrometer
34. It is the best instrument for measuring a thousand of an inch
a. Micrometer
b. Tachometer
c. Caliper
d. Pyrometer
35. What tool will be used in making wood pattern in the foundry
shop?
a. Band saw
b. Drill machine
c. Saw and chisel
d. Hammer
36. The usual ratio of water to soluble oil used as cutting fluid is
_____
a. 50% water to 50% oil
b. 2 water to 1 oil
c. 3 water to 1 oil
d. 4 to 80 water to 1 oil
37. Machine tool used for lying straight lines on metal surfaces
made of sharp tool steel is called
a. Plain scriber
b. A trammel
c. Hermaphrodite caliper
d. Divider
38. A lathe machine threading mechanism is called
a. Reverse gear and lever
b. Spindle gear
c. Changed stud gear
d. All of these
39. Which of the following is not used to resemble the shape of tool
bit?
a. Round nose
b. Center cut
c. Thread cutting
d. Square nose
40. A lathe with multiple cutting stations called
a. Turret lathe
b. Engine lathe
c. Manual lathe
d. None of these
41. Device used to measure accurately speed called
a. Speedometer
b. Dial indicator
c. Tachometer
d. Dial gage
42. A mechanism, which usually do the indexing in a machine tool,
is called
a. Universal chuck
b. Slooter
c. Dividing head
d. Indexing
43. Recommended best cutting angle of drill for work on steel or
cast iron is _____ degrees.
a. 48
b. 63
c. 59
d. 50
44. What is the common shop practice to prevent solder from
running away from surface to be joined?
a. All of these
b. Surround the work with clay
c. Introduce around the work rolled wet cloth
d. Put asbestos sheeting around the work

45. Name the type of chuck commonly used for holding work piece
in a lathe operation? Example 3-jaw universal chuck, 4-jaw
independent chuck.
a. Magnetic jaw chuck
b. 2-jaw independent
c. 8-jaw universal
d. Combination
46. A machinery operation where by done with the work accurately
fastened has a reciprocating motion and the tool head is stationary
is called
a. Shaping
b. Planning
c. Turning
d. Reaming
47. What happens to a drill if the operating speed is too fast?
a. Drill will crack
b. Drill will become overheated And will bend
c. Drill will become overheated and will be drawn from the

steel
d. Drill will become very dull and wear dust

48. Which do not belong to foundry or metal casting shop
a. Shake out machine
b. Molding machine
c. Core making
d. Forging
49. It is an arbitrary modification by removing a small portion of a
tooth material at the tip of the gear tooth.
a. Tip removal
b. Tip under cut
c. Tip relief
d. Pressure angle cut

50. What is the difference between the shaper and a planer?
a. The tool of a shaper moves while the planer is stationary
b. The shaper can perform slotting operation while the planer

cannot
c. The shaper handles large pieces while the planer handles only
small pieces
d. The tool of the shaper moves in reciprocating motion while the

tool in the planer moves in rotary motion.

Test

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Test

Uploaded by

Copyright:

Available Formats

TEST NO.

b. Side cutting edge

a. Beside the land

b. Nearing the shank

c. Close to the future

d. At the tip portion

d. Safety notices in markers / boards

b. Cotter pin set

d. Set screw point

a. End cutting edge

a. Rough cutting of work piece

b. Modify the shape of the cutting tools

c. Use correctly shape of the cutting tools

a. Wearing denim pants / safety shoes

b. Wearing a canvass apron

c. Operating with safety gloves

d. Wearing safety goggles / heating aid

c. Double VEE block

a. Lathe drive plate

b. Clamp toe dog

d. Steady center rest

d. Cubic boron nitride

d. Blow / pin holes

c. Saw and chisel

a. 50% water to 50% oil

a. Reverse gear and lever

c. Changed stud gear

b. Surround the work with clay

c. Introduce around the work rolled wet cloth

d. Put asbestos sheeting around the work

a. Magnetic jaw chuck

a. Drill will crack

b. Drill will become overheated And will bend

c. Drill will become overheated and will be drawn from the

d. Drill will become very dull and wear dust

a. Shake out machine

b. Tip under cut

d. Pressure angle cut

a. The tool of a shaper moves while the planer is stationary

b. The shaper can perform slotting operation while the planer

d. The tool of the shaper moves in reciprocating motion while the

You might also like