Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
743 views

Physics Presentation Class 10

A battery contains two dissimilar electrodes immersed in an electrolyte that allows electrons to flow from one electrode to the other through an external circuit. The dry cell uses a zinc can and carbon rod surrounded by manganese dioxide and filler as electrodes in a solution of zinc chloride and ammonium chloride. Lead storage batteries use lead and lead dioxide electrodes in concentrated sulfuric acid. Ohm's law states that the current through a conductor is directly proportional to the voltage applied and inversely proportional to the resistance of the conductor. Power is defined as the rate at which electrical work is done and can be calculated as the product of current and voltage or voltage squared over resistance.

Uploaded by

Akash Sehrawat
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
743 views

Physics Presentation Class 10

A battery contains two dissimilar electrodes immersed in an electrolyte that allows electrons to flow from one electrode to the other through an external circuit. The dry cell uses a zinc can and carbon rod surrounded by manganese dioxide and filler as electrodes in a solution of zinc chloride and ammonium chloride. Lead storage batteries use lead and lead dioxide electrodes in concentrated sulfuric acid. Ohm's law states that the current through a conductor is directly proportional to the voltage applied and inversely proportional to the resistance of the conductor. Power is defined as the rate at which electrical work is done and can be calculated as the product of current and voltage or voltage squared over resistance.

Uploaded by

Akash Sehrawat
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 16

THE ELECTRIC BATTERY

Y A BATTERY is a source of
electric energy. A simple
battery contains two
dissimilar metals,
called ELECTRODES, and a
solution called the
ELECTROLYTE, in which
the electrodes are
partially immersed.
THE ELECTRIC BATTERY
Y An example of a simple
battery would be one in which
zinc and carbon are used as
the electrodes, while a dilute
acid, such as sulfuric acid
(dilute), acts as the
electrolyte. The acid dissolves
the zinc and causes zinc ions
to leave the electrode. Each
zinc ion which enters the
electrolyte leaves two
electrons on the zinc plate.
The Dry cell is relatively
inexpensive and quite
portable. It has many uses
such as in flashlights and
radios. The anode consists
of a Zinc can in contact with
a moist paste of ZnCl2 and
NH4Cl. A carbon rod
surrounded by MnO2 and
filler is the cathode.
Lead Storage Cell
The basic features of the lead
storage cell are electrodes of
lead and lead dioxide, dipping
into concentrated sulfuric acid

Both electrode reactions produce lead sulfate, which adheres to


the electrode. When the cell discharges, sulfuric acid is used up
and water is produced. The state of the cell can be determined by
measuring the density of the electrolyte solution (the density of
water is about 70% that of the sulfuric acid solution).
ELECTRIC CURRENT
Y An electric CURRENT exists
whenever electric charge flows
through a region, e.g., a simple
light bulb circuit. The
magnitude of the current is
measured in AMPERES
(Amps/A), where
Y 1 ampere = 1coulomb/second
Y I = º/  t.
CONVENTIONAL CURRENT vs ELECTRON
CURRENT
Y The direction of
CONVENTIONAL CURRENT is in
the direction in which positive
charge flows. In gases and
liquids both positive and
negative ions move. Only
negative charges, i.e.,
electrons, move through solids
and this is referred to as
ELECTRON CURRENT. For
historical reasons, conventional
current is used in referring to
the direction of electric charge
flow.
OHM'S LAW
Y The magnitude of the electric current that flows through a closed
circuit depends directly on the voltage between the battery
terminals and inversely to the circuit resistance. The relationship
that connects current, voltage and resistance is known as OHM'S
LAW and is written as follows:
Y I = V/R or V = IR
Y The current is measured in amperes, the voltage
in volts and the resistance in ohms (D).
Resistors
Y Resistors are used to control
the amount of current flowing
in a circuit
Y Resistors have resistances from
less than 1 ohm to millions of
ohms
Y The two main types of
resistors:
Wire-wound (coil of fine
wire)resistors
Composition (carbon)
resistors
Resistors
Y Symbol on a schematic
diagram

For the color code, the first


two colors represent the first
two digits in the value of the
resistor, the third represents
the power of ten that it must
be multiplied by, and the
fourth is the tolerance.
RESISTIVITY
Y RESISTIVITY => When electric charge flows
through a circuit it encounters electrical
RESISTANCE. The resistance of a metal
conductor is a property which depends on its
dimensions, material and temperature. At a
specific temperature, the resistance (R) of a
metal wire of length L and cross-sectional area
A is given by
Y R = L/A
Y It is a constant of proportionality called the
RESISTIVITY. The unit of resistance is the ohm
and the unit of resistivity is ohm-meter.
Resistivity and Temperature
ELECTRIC POWER
Y Work is required to transfer
charge through an electric
circuit. The work required
depends on the amount of
charge transferred through the
circuit and the potential
difference between the
terminals of the battery:
W = ºV.
Y The rate at which work is done
to maintain an electric current
in a circuit is termed ELECTRIC
POWER
ELECTRIC POWER
Y ELECTRIC POWER equals the product of the current
I and the potential difference V, i.e., P = IV.
Y The SI unit of power is the watt (W), where
1 W = 1 J/s. The kilowatt is a commonly used unit
where I kilowatt = 1000 watts.
Y The electric energy produced by the source of emf
is dissipated in the circuit in the form of heat.
Y The kilowatt hour (kWh) is commonly used to
represent electric energy production and
consumption where I kWh = 3.6 x 106 J.
Electric Power
Y In a circuit of resistance R, the rate
at which electrical energy is
converted to heat energy is given by
Y P = IV but V = IR, then P = I(IR) =I2R
Y where I2R is known as JOULE
HEATING.
Y An alternate formula for power can
be written, since I = V/R, then P = IV
= (V/R)V = V2 /R
Y P=V2 /R= I2R are power formulas
which apply only to resistors
Y P = IV Applies to any device

You might also like