The heat sinks are used in electronic systems to remove heat from the chip and effectively transfer it to the ambient. The heat sink geometry is designed by the mechanical engineers with the primary aim of reducing the thermal resistance of the heat sink for better cooling in the electronic systems. Due to the proximity of the heat sink with the ICs, the RF fields created by RF currents in the ICs/PCBs gets coupled to heat sinks. Hence, the coupled RF current can cause radiated emission. This radiated noise from the device can couple and disturb the functioning of the nearby electronic systems. Also this radiated emission from the device poses a problem to the system compliance with respect to EMI/EMC regulations. The international EMI/EMC standards require the radiated emission from the electronic devices to be kept below the specified limits. As a result the design of Heat Sink is very important factor for the efficient operation of the electronic equipment. In this project design optimization of a Heat sink in a Power amplifier is performed to reduce the weight and size .Power amplifier is electronic equipment mounted in an army vehicle. The power modules inside the amplifier generates a heat of 1440 Watts and a temperature of 140 0c.Two Heat sinks are used to dissipate the heat generated inside the equipment and maintain a temperature of less than 850c. The existing heat sink which is being used is weighing around 10.3kgs and height of 51mm; as a result the unit is very robust. The objective of my project is To design & optimize the heat sink to reduce the weight and size. The optimized heat sink should also dissipate heat generated by power modules and maintain a temperature of less than 850c inside. To achieve the design a steady state thermal analysis will be performed on the heat sink and plot the Temperature distribution on the fins. Based on the above analysis results we will increase/decrease the number of fins, thickness of fins, and height of fins to reduce the weight of the heat sink. We will perform CFD analysis of the power amplifier by mounting the optimized heat sink and plot temperature, pressure and velocity distribution in the power amplifier enclosure. Efforts are made to optimize temperature, pressure and velocity distribution in the power amplifier enclosure by reorienting the power modules in the enclosure. UNIGRAPHICS software is used for 3D modeling SOLID WORKS FLOW SIMULATION software is used for thermal and CFD analysis.
This document defines and classifies the components of mechanisms. It discusses links, kinematic pairs, kinematic chains, mechanisms, and machines. Links can be unary, binary, ternary or quaternary based on the number of nodes. Kinematic pairs combine two links and allow specific relative motions. Pairs are classified by contact type, constraint, and possible motions such as revolute, prismatic, or spherical. A kinematic chain transmits defined motion by coupling pairs. A mechanism is a kinematic chain with one fixed link. Mobility is determined using Gruebler's criterion involving links, pairs, and degrees of freedom. Kinematic inversion obtains different mechanisms from the same chain by fixing different links.
This document discusses two-dimensional vector variable problems in structural mechanics. It describes plane stress, plane strain and axisymmetric problems, and provides the stress-strain relations for materials under these conditions. It also discusses thin structures like disks and long prismatic shafts. Additionally, it covers dynamic analysis and vibration of structures, describing free vibration, forced vibration and types of vibration. Equations of motion are developed using Lagrange's approach and the weak form method. Mass and stiffness matrices for axial rod and beam elements are also presented.
The document discusses surface finish and roughness measurement. It defines terms like surface texture, roughness, waviness, and provides explanations of different measurement methods and parameters like Ra, Rz, and Rmax. Measurement methods covered include comparison methods, profilometers, and instruments like the Taylor-Hobson Talysurf that can numerically analyze surface roughness.
The document discusses mechanical measurements and metrology. It covers topics like limits, fits, tolerances and gauging. Specifically, it defines tolerance, describes different types of tolerances like unilateral, bilateral and compound. It also discusses interchangeability, selective assembly, fits, tolerance grades and general terminology used in metrology like basic size, actual size, deviations etc. The objective is to equip students with knowledge of these important concepts in mechanical measurements.
The document discusses different methods of NC part programming including manual part programming, computer-assisted part programming, manual data input, NC programming using CAD/CAM, and computer automated part programming. It also provides details on punched tape formats, G-codes and M-codes used in NC part programming.
Dynamo meters are the electronic devices that are widely used to the purpose of force analysis in various field of operations. There is various types of dynamometers such as
Lathe tool dynamometer
Milling tool dynamometer
Drilling tool dynamometer
Kinematic synthesis deals with determining link lengths and orientations of mechanisms to satisfy motion requirements. This document discusses several key concepts in kinematic synthesis of planar mechanisms, including:
1) Movability/mobility synthesis which determines the degrees of freedom using Gruebler's criterion. The simplest mechanism is the four-bar linkage.
2) Transmission angle synthesis which aims to position links for maximum torque transmission, usually near 90°.
3) Limit positions and dead centers which are configurations of four-bar mechanisms where links are collinear.
4) Graphical synthesis methods using the pole and relative pole to determine link lengths and positions based on input/output motion specifications.
This document defines and classifies the components of mechanisms. It discusses links, kinematic pairs, kinematic chains, mechanisms, and machines. Links can be unary, binary, ternary or quaternary based on the number of nodes. Kinematic pairs combine two links and allow specific relative motions. Pairs are classified by contact type, constraint, and possible motions such as revolute, prismatic, or spherical. A kinematic chain transmits defined motion by coupling pairs. A mechanism is a kinematic chain with one fixed link. Mobility is determined using Gruebler's criterion involving links, pairs, and degrees of freedom. Kinematic inversion obtains different mechanisms from the same chain by fixing different links.
This document discusses two-dimensional vector variable problems in structural mechanics. It describes plane stress, plane strain and axisymmetric problems, and provides the stress-strain relations for materials under these conditions. It also discusses thin structures like disks and long prismatic shafts. Additionally, it covers dynamic analysis and vibration of structures, describing free vibration, forced vibration and types of vibration. Equations of motion are developed using Lagrange's approach and the weak form method. Mass and stiffness matrices for axial rod and beam elements are also presented.
The document discusses surface finish and roughness measurement. It defines terms like surface texture, roughness, waviness, and provides explanations of different measurement methods and parameters like Ra, Rz, and Rmax. Measurement methods covered include comparison methods, profilometers, and instruments like the Taylor-Hobson Talysurf that can numerically analyze surface roughness.
The document discusses mechanical measurements and metrology. It covers topics like limits, fits, tolerances and gauging. Specifically, it defines tolerance, describes different types of tolerances like unilateral, bilateral and compound. It also discusses interchangeability, selective assembly, fits, tolerance grades and general terminology used in metrology like basic size, actual size, deviations etc. The objective is to equip students with knowledge of these important concepts in mechanical measurements.
The document discusses different methods of NC part programming including manual part programming, computer-assisted part programming, manual data input, NC programming using CAD/CAM, and computer automated part programming. It also provides details on punched tape formats, G-codes and M-codes used in NC part programming.
Dynamo meters are the electronic devices that are widely used to the purpose of force analysis in various field of operations. There is various types of dynamometers such as
Lathe tool dynamometer
Milling tool dynamometer
Drilling tool dynamometer
Kinematic synthesis deals with determining link lengths and orientations of mechanisms to satisfy motion requirements. This document discusses several key concepts in kinematic synthesis of planar mechanisms, including:
1) Movability/mobility synthesis which determines the degrees of freedom using Gruebler's criterion. The simplest mechanism is the four-bar linkage.
2) Transmission angle synthesis which aims to position links for maximum torque transmission, usually near 90°.
3) Limit positions and dead centers which are configurations of four-bar mechanisms where links are collinear.
4) Graphical synthesis methods using the pole and relative pole to determine link lengths and positions based on input/output motion specifications.
The document discusses the fundamentals of theory of machines and its subdivisions. It covers the following key points:
1. Theory of machines deals with the study of relative motion between machine parts and forces acting on them. It is subdivided into kinematics, dynamics, kinetics, and statics.
2. Kinematics studies relative motion, dynamics studies forces and their effects on moving parts, kinetics studies inertia forces, and statics studies forces on stationary parts.
3. Fundamental concepts like space, time, matter, body, mass, and force are defined. Newton's laws of motion are also summarized.
4. Methods for analyzing reciprocating engines like graphical and analytical methods are outlined. Forces
Kinematics of machines can involve either analyzing an existing mechanism's motion or synthesizing a new mechanism to achieve a desired motion. Kinematic synthesis involves selecting the type of mechanism, determining the number of links needed, and defining the link dimensions. Dimensional synthesis aims to develop link dimensions such that the mechanism's output motion matches the desired motion at select precision points, often spaced using Chebyshev's method to minimize error between points. Slider-crank mechanisms can be synthesized by relating the slider displacement to crank angle at precision points defined using Chebyshev spacing.
What is process planning .Difficulties in traditional process planning,CAPP Model,Types of CAPP ,1.Retrieval type CAPP (variant) systems.
2.Generative CAPP systems.
3.Hybrid CAPP systems.
Process planning system , Machinability data systems , Benefits of CAPP
The document discusses static force analysis and equilibrium of mechanisms. It covers topics like static equilibrium, equilibrium of two and three force members, members with two forces and torque, free body diagrams, and the principle of virtual work. Examples of static force analysis of four bar and slider-crank mechanisms are presented. Methods to determine the forces and torques required for static equilibrium are demonstrated through graphical techniques like force triangles and the principle of virtual work.
Need for cooling of an aircraft. types of air-refrigeration system, DART, Advantages of air refrigeration system, Open and closed cycle air refrigeration,
The document discusses isoparametric finite elements. It defines isoparametric, superparametric, and subparametric elements. It provides examples of shape functions for 4-noded rectangular, 6-noded triangular, and 8-noded rectangular isoparametric elements. It also discusses coordinate transformation from the natural to global coordinate system using these shape functions and calculating the Jacobian.
The document discusses instantaneous centers in mechanisms. It defines an instantaneous center as a point where one member rotates permanently or instantaneously around another, or where the velocities of two members are equal in both direction and magnitude. There are three types of instantaneous centers: fixed, permanent, and neither fixed nor permanent (secondary). Properties are that at the center, two links have no relative velocity and the same linear velocity relative to a third link. Instantaneous centers can be located by determining the number, identifying fixed and permanent centers, and using Kennedy's theorem to find secondary centers which lie on a straight line. An example four-bar mechanism shows the different types of centers.
Whirling of shafts occurs due to rotational imbalance of a shaft, even in the absence of external loads, which causes resonance to occur at certain speeds, known as critical speeds.
The document discusses geometric modeling techniques used in computer aided design (CAD). It describes three main types of geometric modeling: wireframe, surface, and solid modeling. Wireframe modeling represents an object with lines and curves, surface modeling uses surfaces, and solid modeling provides a complete 3D representation of mass properties. Hermite cubic splines are discussed as an interpolation technique for generating smooth curves through data points with continuous slopes and curvatures. Parametric curve representations are also presented as they allow curves to be easily defined over a range of parameter values.
Surface modeling represents the surfaces of 3D objects and can be used to model complex shapes like vehicles, ships, and aircraft wings. There are two main types of surface modeling: parametric surfaces and implicit surfaces. Parametric surfaces use a set of equations to define the x, y, and z coordinates as functions of parameters u and v. Common parametric surface types include planes, ruled surfaces, surfaces of revolution, and tabulated cylinders. Implicit surfaces use a single polynomial equation to define the surface. Surface modeling provides more realistic representations than wireframe models and can be used for applications like finite element analysis, machining tool paths, and rendering models.
Theory of machines_static and dynamic force analysisKiran Wakchaure
This document contains information about static and dynamic force analysis in machines. It discusses various topics including:
1) Types of forces such as static loads, dynamic loads, tension, compression, shear force, and torsion.
2) Laws of motion including Newton's three laws of motion.
3) Moment of inertia which is a mass property that determines the torque needed for angular acceleration. It depends on the shape and mass distribution of an object.
4) Analysis of simple and compound pendulums including calculations of their periodic times and frequencies of oscillation based on length, mass, and radius of gyration.
Unit-3 - Velocity and acceleration of mechanisms, Kinematics of machines of VTU Syllabus prepared by Hareesha N Gowda, Asst. Prof, Dayananda Sagar College of Engg, Blore. Please write to hareeshang@gmail.com for suggestions and criticisms.
This document provides an overview of ANSYS Workbench software for structural and thermal analysis. It describes the user interface, types of analysis available including linear static, modal, heat transfer and buckling. It outlines the steps to set up a static structural analysis including importing geometry, applying materials, meshing, boundary conditions and solving. License types are also summarized. The goal is to teach the basics of using simulation capabilities in ANSYS Workbench.
Possible Interview Questions/Contents From Manufacturing Technology IIDr. Ramesh B
1. Machining is a process that removes material from a workpiece through cutting or other shear mechanisms in order to change its shape or size. The three fundamental machining parameters are cutting speed, depth of cut, and feed.
2. Material removal rate is the volume of material removed per minute during machining operations like turning, where it is calculated as MRR=Vfd. Chip formation affects surface finish, cutting forces, temperature, tool life, and tolerances.
3. Tool wear occurs due to interactions between the tool and chip like adhesion and abrasion, leading to flank wear, crater wear, chipping, and breakage. Tool wear degrades surface finish and increases tolerances and machining
This document provides an overview of position analysis techniques for linkages and mechanisms. It discusses coordinate systems, position and displacement concepts, and methods for graphical and algebraic position analysis. Graphical methods involve drawing the linkage to scale based on given parameters and measuring positions. Algebraic methods develop vector loop equations in terms of complex numbers and solve for unknown positions and angles. Specific techniques are presented for common linkages including fourbars, slider-cranks, and geared fivebars.
Thermocouples are temperature measurement devices that operate based on the Seebeck effect. They produce a voltage when two dissimilar metals are joined together at both ends and there is a temperature difference between the ends. Thermocouples have various applications in industries like steel, manufacturing and power plants. They are commonly used to measure temperature in metal cutting operations. An experiment measured the temperature distribution on a cutting tool during metal cutting using a K-type thermocouple and found that temperature was highest near the cutting edge and increased with cutting speed. Thermocouples have advantages of being rugged and having a wide temperature range but also have limitations like non-linear output and complexity.
Tool life is measured by the time period from when a tool starts cutting until failure or until it needs resharpening. Tool life can be measured in units of time, number of pieces cut, volume of material removed, or length of cut. Tools typically fail due to high temperatures, mechanical impacts, or gradual wear. Wear occurs on the flank and crater faces of tools and is caused by abrasion, diffusion, electrochemical reactions, and other mechanisms. Factors like cutting speed, workpiece properties, tool geometry, and cooling influence tool life.
- The document discusses one-dimensional finite element analysis.
- It describes the derivation of shape functions for linear one-dimensional elements like a bar element. Shape functions define the variation of displacement within the element.
- The stiffness matrix, which represents the element's resistance to deformation, is also derived for a basic linear bar element. It is shown to be symmetric and its properties are discussed.
- Examples are provided to demonstrate calculating displacements at points within a one-dimensional element using the shape functions.
This document contains information about computer-assisted part programming using APT (Automatically Programmed Tool) language. It discusses the tasks divided between the human programmer and computer, including input translation, arithmetic computations, editing, and post processing. It also describes defining part geometry, specifying tool paths and operations, and includes examples of part programs for drilling and milling operations.
Finite element analysis (FEA) is a numerical technique used to approximate solutions to boundary value problems by dividing the domain into smaller elements. The document discusses the three main stages of FEA: building the model, solving the model, and displaying the results. It provides details on how to create nodes and finite elements to represent an object's geometry, assign material properties and constraints, define the type of analysis, and select parameters to display in the results. Examples of different types of FEA analyses are also listed, such as static, thermal, modal, and buckling analyses.
DESIGN AND FABRICATION OF THERMO ACOUSTIC REFRIGERATORP singh
In an age of impending energy and environmental crises, current cooling technologies continue to generate greenhouse gases with high energy costs. Thermo acoustic refrigeration is an innovative alternative for cooling that is both clean and inexpensive.
Thermo acoustic refrigerators are systems which use sound waves and a non-flammable mixture of inert gases to generate refrigeration effect. The main components are a closed cylinder, an acoustic driver, a porous component called a stack, and two heat-exchangers. Application of acoustic waves through the driver makes the gas resonant. As the gas oscillates back and forth, it creates a temperature difference along the length of the stack. This temperature change is due to compression and expansion of the gas by the sound pressure and the rest is a consequence of heat transfer between the gas and the stack. The temperature difference is used to remove heat from the cold side and reject it at the hot side of the system, producing cooling.
This document describes the design and fabrication of a mini air cooler. The authors modified an ordinary table fan by adding a copper tube with fins and a cooling chamber. Cold water is circulated through the copper tube using an aquarium pump to reduce the heat in the surrounding environment. The table fan blows air over the copper tube and fins, which increases the cooling effect. The device aims to provide air cooling without high power consumption, benefiting areas with limited access to electricity. It was found to decrease air temperature by 8-10°C through this simple, low-cost modification of a standard table fan.
The document discusses the fundamentals of theory of machines and its subdivisions. It covers the following key points:
1. Theory of machines deals with the study of relative motion between machine parts and forces acting on them. It is subdivided into kinematics, dynamics, kinetics, and statics.
2. Kinematics studies relative motion, dynamics studies forces and their effects on moving parts, kinetics studies inertia forces, and statics studies forces on stationary parts.
3. Fundamental concepts like space, time, matter, body, mass, and force are defined. Newton's laws of motion are also summarized.
4. Methods for analyzing reciprocating engines like graphical and analytical methods are outlined. Forces
Kinematics of machines can involve either analyzing an existing mechanism's motion or synthesizing a new mechanism to achieve a desired motion. Kinematic synthesis involves selecting the type of mechanism, determining the number of links needed, and defining the link dimensions. Dimensional synthesis aims to develop link dimensions such that the mechanism's output motion matches the desired motion at select precision points, often spaced using Chebyshev's method to minimize error between points. Slider-crank mechanisms can be synthesized by relating the slider displacement to crank angle at precision points defined using Chebyshev spacing.
What is process planning .Difficulties in traditional process planning,CAPP Model,Types of CAPP ,1.Retrieval type CAPP (variant) systems.
2.Generative CAPP systems.
3.Hybrid CAPP systems.
Process planning system , Machinability data systems , Benefits of CAPP
The document discusses static force analysis and equilibrium of mechanisms. It covers topics like static equilibrium, equilibrium of two and three force members, members with two forces and torque, free body diagrams, and the principle of virtual work. Examples of static force analysis of four bar and slider-crank mechanisms are presented. Methods to determine the forces and torques required for static equilibrium are demonstrated through graphical techniques like force triangles and the principle of virtual work.
Need for cooling of an aircraft. types of air-refrigeration system, DART, Advantages of air refrigeration system, Open and closed cycle air refrigeration,
The document discusses isoparametric finite elements. It defines isoparametric, superparametric, and subparametric elements. It provides examples of shape functions for 4-noded rectangular, 6-noded triangular, and 8-noded rectangular isoparametric elements. It also discusses coordinate transformation from the natural to global coordinate system using these shape functions and calculating the Jacobian.
The document discusses instantaneous centers in mechanisms. It defines an instantaneous center as a point where one member rotates permanently or instantaneously around another, or where the velocities of two members are equal in both direction and magnitude. There are three types of instantaneous centers: fixed, permanent, and neither fixed nor permanent (secondary). Properties are that at the center, two links have no relative velocity and the same linear velocity relative to a third link. Instantaneous centers can be located by determining the number, identifying fixed and permanent centers, and using Kennedy's theorem to find secondary centers which lie on a straight line. An example four-bar mechanism shows the different types of centers.
Whirling of shafts occurs due to rotational imbalance of a shaft, even in the absence of external loads, which causes resonance to occur at certain speeds, known as critical speeds.
The document discusses geometric modeling techniques used in computer aided design (CAD). It describes three main types of geometric modeling: wireframe, surface, and solid modeling. Wireframe modeling represents an object with lines and curves, surface modeling uses surfaces, and solid modeling provides a complete 3D representation of mass properties. Hermite cubic splines are discussed as an interpolation technique for generating smooth curves through data points with continuous slopes and curvatures. Parametric curve representations are also presented as they allow curves to be easily defined over a range of parameter values.
Surface modeling represents the surfaces of 3D objects and can be used to model complex shapes like vehicles, ships, and aircraft wings. There are two main types of surface modeling: parametric surfaces and implicit surfaces. Parametric surfaces use a set of equations to define the x, y, and z coordinates as functions of parameters u and v. Common parametric surface types include planes, ruled surfaces, surfaces of revolution, and tabulated cylinders. Implicit surfaces use a single polynomial equation to define the surface. Surface modeling provides more realistic representations than wireframe models and can be used for applications like finite element analysis, machining tool paths, and rendering models.
Theory of machines_static and dynamic force analysisKiran Wakchaure
This document contains information about static and dynamic force analysis in machines. It discusses various topics including:
1) Types of forces such as static loads, dynamic loads, tension, compression, shear force, and torsion.
2) Laws of motion including Newton's three laws of motion.
3) Moment of inertia which is a mass property that determines the torque needed for angular acceleration. It depends on the shape and mass distribution of an object.
4) Analysis of simple and compound pendulums including calculations of their periodic times and frequencies of oscillation based on length, mass, and radius of gyration.
Unit-3 - Velocity and acceleration of mechanisms, Kinematics of machines of VTU Syllabus prepared by Hareesha N Gowda, Asst. Prof, Dayananda Sagar College of Engg, Blore. Please write to hareeshang@gmail.com for suggestions and criticisms.
This document provides an overview of ANSYS Workbench software for structural and thermal analysis. It describes the user interface, types of analysis available including linear static, modal, heat transfer and buckling. It outlines the steps to set up a static structural analysis including importing geometry, applying materials, meshing, boundary conditions and solving. License types are also summarized. The goal is to teach the basics of using simulation capabilities in ANSYS Workbench.
Possible Interview Questions/Contents From Manufacturing Technology IIDr. Ramesh B
1. Machining is a process that removes material from a workpiece through cutting or other shear mechanisms in order to change its shape or size. The three fundamental machining parameters are cutting speed, depth of cut, and feed.
2. Material removal rate is the volume of material removed per minute during machining operations like turning, where it is calculated as MRR=Vfd. Chip formation affects surface finish, cutting forces, temperature, tool life, and tolerances.
3. Tool wear occurs due to interactions between the tool and chip like adhesion and abrasion, leading to flank wear, crater wear, chipping, and breakage. Tool wear degrades surface finish and increases tolerances and machining
This document provides an overview of position analysis techniques for linkages and mechanisms. It discusses coordinate systems, position and displacement concepts, and methods for graphical and algebraic position analysis. Graphical methods involve drawing the linkage to scale based on given parameters and measuring positions. Algebraic methods develop vector loop equations in terms of complex numbers and solve for unknown positions and angles. Specific techniques are presented for common linkages including fourbars, slider-cranks, and geared fivebars.
Thermocouples are temperature measurement devices that operate based on the Seebeck effect. They produce a voltage when two dissimilar metals are joined together at both ends and there is a temperature difference between the ends. Thermocouples have various applications in industries like steel, manufacturing and power plants. They are commonly used to measure temperature in metal cutting operations. An experiment measured the temperature distribution on a cutting tool during metal cutting using a K-type thermocouple and found that temperature was highest near the cutting edge and increased with cutting speed. Thermocouples have advantages of being rugged and having a wide temperature range but also have limitations like non-linear output and complexity.
Tool life is measured by the time period from when a tool starts cutting until failure or until it needs resharpening. Tool life can be measured in units of time, number of pieces cut, volume of material removed, or length of cut. Tools typically fail due to high temperatures, mechanical impacts, or gradual wear. Wear occurs on the flank and crater faces of tools and is caused by abrasion, diffusion, electrochemical reactions, and other mechanisms. Factors like cutting speed, workpiece properties, tool geometry, and cooling influence tool life.
- The document discusses one-dimensional finite element analysis.
- It describes the derivation of shape functions for linear one-dimensional elements like a bar element. Shape functions define the variation of displacement within the element.
- The stiffness matrix, which represents the element's resistance to deformation, is also derived for a basic linear bar element. It is shown to be symmetric and its properties are discussed.
- Examples are provided to demonstrate calculating displacements at points within a one-dimensional element using the shape functions.
This document contains information about computer-assisted part programming using APT (Automatically Programmed Tool) language. It discusses the tasks divided between the human programmer and computer, including input translation, arithmetic computations, editing, and post processing. It also describes defining part geometry, specifying tool paths and operations, and includes examples of part programs for drilling and milling operations.
Finite element analysis (FEA) is a numerical technique used to approximate solutions to boundary value problems by dividing the domain into smaller elements. The document discusses the three main stages of FEA: building the model, solving the model, and displaying the results. It provides details on how to create nodes and finite elements to represent an object's geometry, assign material properties and constraints, define the type of analysis, and select parameters to display in the results. Examples of different types of FEA analyses are also listed, such as static, thermal, modal, and buckling analyses.
DESIGN AND FABRICATION OF THERMO ACOUSTIC REFRIGERATORP singh
In an age of impending energy and environmental crises, current cooling technologies continue to generate greenhouse gases with high energy costs. Thermo acoustic refrigeration is an innovative alternative for cooling that is both clean and inexpensive.
Thermo acoustic refrigerators are systems which use sound waves and a non-flammable mixture of inert gases to generate refrigeration effect. The main components are a closed cylinder, an acoustic driver, a porous component called a stack, and two heat-exchangers. Application of acoustic waves through the driver makes the gas resonant. As the gas oscillates back and forth, it creates a temperature difference along the length of the stack. This temperature change is due to compression and expansion of the gas by the sound pressure and the rest is a consequence of heat transfer between the gas and the stack. The temperature difference is used to remove heat from the cold side and reject it at the hot side of the system, producing cooling.
This document describes the design and fabrication of a mini air cooler. The authors modified an ordinary table fan by adding a copper tube with fins and a cooling chamber. Cold water is circulated through the copper tube using an aquarium pump to reduce the heat in the surrounding environment. The table fan blows air over the copper tube and fins, which increases the cooling effect. The device aims to provide air cooling without high power consumption, benefiting areas with limited access to electricity. It was found to decrease air temperature by 8-10°C through this simple, low-cost modification of a standard table fan.
Experimental Investigation of Heat Transfer through Rectangular and Trapezoid...IRJET Journal
The document describes an experimental investigation of heat transfer through rectangular and trapezoidal fins made of aluminum 6063 alloy. Rectangular and trapezoidal fins were fabricated from the alloy and experiments were conducted under steady state conditions. Local temperature, heat flux, heat transfer coefficients, and Reynolds numbers were estimated. The findings showed that forced convection was more effective than free convection, and the trapezoidal fin enhanced heat transfer by up to 48% compared to the rectangular fin under different heat supply conditions. The document provides details on the experimental setup, material properties of the aluminum 6063 alloy, and methodology for collecting temperature readings along the fins.
IRJET- Design and Fabrication of Thermo Acoustic RefrigeratorIRJET Journal
This document describes the design and fabrication of a thermoacoustic refrigerator. Some key points:
1. Thermoacoustic refrigeration uses sound waves to alternately compress and relax gas particles in a tube, transferring heat without moving parts.
2. The refrigerator consists of a resonator tube containing a stack of closely spaced surfaces through which a sound wave oscillates. Heat is transferred between the gas and stack surfaces.
3. Experiments investigated different stack geometries and materials to optimize heat transfer and the refrigerator's performance. Temperature sensors measured the temperature difference created.
Experimental Investigation of Natural Convection Heat Transfer Enhancement fr...IRJET Journal
This document describes an experimental investigation of natural convection heat transfer from rectangular fin arrays with combinations of V-notches and perforations. Four fin array configurations were tested: one without notches or perforations (un-notched), and three with different combinations of V-notches and perforations removing different percentages of the fin area. The fin arrays were heated to different temperatures and the resulting heat transfer coefficients were measured and compared. The results showed that the combination of V-notches and perforations both increased the surface area and the turbulence near the fins, allowing more air contact and higher heat transfer coefficients compared to the un-notched fins. Among the configurations tested, the fin array with 20% of its area removed
This document summarizes a research project that aims to thermally enhance a plate-fin heat exchanger using secondary structures called cross-cuts. Cross-cuts are sections removed from fins perpendicular to airflow to disrupt boundary layer development. The project will test various cross-cut configurations and validate correlations from a previous study. A plate-fin heat sink will be compared to designs with one and two cross-cuts. The goal is to validate that a single cross-cut provides the best thermal performance improvement of 4-13% over the base design within a pumping power range of 0.01-1W.
1) The document analyzes heat transfer in a double pipe heat exchanger with helical tape inserts in the annulus of the inner pipe using computational fluid dynamics (CFD).
2) A 3D model is developed and simulations are run using the SST k-ω turbulent model to analyze how helical tape inserts influence heat transfer and pressure drop at different pitch lengths and Reynolds numbers.
3) The results show that helical tape inserts increase the heat transfer rate but also increase pressure drop due to flow disruption. Nusselt number and friction factor are found to correlate well with Reynolds number for enhancing heat transfer.
IRJET - Experimental Investigation of Heat Transfer through Rectangular and ...IRJET Journal
1. The document experimentally investigates heat transfer through rectangular and trapezoidal fins made of aluminum 6063 alloy with variable cross-sections. Rectangular fins measuring 110x50x10mm and trapezoidal fins measuring 110x30x10mm were fabricated and their heat transfer coefficients were measured under different heat input conditions.
2. Several studies on heat transfer through different fin geometries are reviewed. One study found that sideward vertically oriented trapezoidal fins performed best for natural convection cooling. Another study computationally analyzed heat transfer from vertical trapezoidal and rectangular fins and found trapezoidal fins performed better.
3. The document aims to compare heat transfer through rectangular, trapezoidal and parabolic
Review of Convective Heat Transfer from Plate Fins Under Natural and Mixed Co...IRJET Journal
This document reviews research on convective heat transfer from plate fins under natural and mixed convection conditions. It summarizes several previous studies that investigated the effects of fin geometry (such as fin length, height, width, spacing, thickness) and operating parameters (such as heat supplied, temperature difference) on heat transfer. The studies found that convective heat transfer increases with fin spacing until an optimal spacing is reached, beyond which further increases in spacing decrease heat transfer. Inclination angle and mixed convection were also found to impact heat transfer. The document provides background on using fins to dissipate heat from electronic devices and explores parameters that most affect natural convective heat transfer within constrained heat sink dimensions.
Thermoelectric cooling for industrial enclosureserdinc klima
This white paper discusses the advantages of thermoelectric cooling compared to conventional cooling methods for industrial enclosures. Thermoelectric coolers use the Peltier effect to generate cooling by passing an electric current through semiconductors, eliminating the need for refrigerants or water cooling systems. Recent improvements have increased thermoelectric cooler efficiency up to 400% by using techniques like pulse width modulation. Thermoelectric coolers provide benefits like fewer moving parts for less noise and vibration, flexibility in installation orientation and location, and solid-state operation requiring only electricity. The paper concludes that thermoelectric cooling is emerging as a viable option for certain small-to-medium enclosure applications.
Numerical Analysis of Inverted Notched Fin Array Using Natural ConvectionIOSR Journals
Abstract:Geometry and orientation plays an important role in natural convection heat transfer. For
horizontal rectangular fin array a chimney flow pattern is developed due to density difference. This flow
pattern creates a stagnant zone near central bottom region. That portion does not contribute much towards
heat dissipation. This area is removed from fins and they became inverted notched fins. This modified geometry
reduces material cost, material weight without hampering heat transfer rate. Numerical models are prepaid to
investigate heat transfer characteristics in plane fins and inverted notched fins. This investigation is also
extended over different types of notches and their effectiveness comparison. Fin spacing, fin height, fin length,
heater input, percentage of area removed in the form of inverted notch are the parameters under
consideration. This analysis is done numerically using CFD package (Fluent). It is found that the heat transfer
coefficient of inverted notch fin array is 25% to 35% higher as compared with normal fin array. Also we found
that the triangular shape notch gives better result than trapezoidal and rectangular shape notch.
Key words: Inverted Notched Fin, Chimney Flow, Natural Convection, Heat transfer coefficient enhancement
This document describes an experiment investigating heat transfer using twisted aluminum tape. The experiment aimed to increase the efficiency of a heat exchanger by inducing turbulence in liquid flow using a twisted aluminum tape inserted into the inner pipe. This increased the Reynolds number and heat transfer coefficient compared to without the tape. Temperature measurements found that the outlet temperature of the hot fluid decreased with the tape, indicating increased heat transfer. The increased turbulence from the tape also provided some resistance to fouling buildup. Overall, inserting twisted aluminum tape was found to enhance heat transfer in the heat exchanger.
Experimental Investigation of Heat Transfer Using “Twisted Aluminium Tape”IJERA Editor
Heat exchanger has a wide industrial and engineering applications. Increasing the efficiency of heat exchanger will increase the overall performance of the unit. This paper is about increasing the heat transfer coefficient of heat exchanger by causing a turbulence in the liquid flow through the pipe. For causing the turbulence, liquid flow is subjected to a Twisted Aluminium Tape (TAT) which will increase the Reynolds number of flow. This will ensure heat transfer through the length of flow and thus there will be an increased heat transfer rate. The increased turbulence and higher shear caused by Twisted Aluminium Tape (TAT) will offer resistance to fouling also. KEY ]
The main objectives of the heat transfer analysis is to enhance the heat transfer rate from system to
surrounding. To transfer the heat from any system either by conduction or convection medium. Both modes of
heat transfer has been enhanced by providing an additional equipments in the outer periphery of the heat transfer
system.Fins are basically mechanical structures which are used to cool various structures by the process of
convection. Most part of their design is basically limited by the design of the system. But still certain parameters
and geometry could be modified to better heat transfer. In most of the cases simple fin geometry is preferred such
as rectangular fins and circular fins. Many experimental works has been done to improve the heat release of the
internal combustion engine cylinder and improves fin efficiency.This study presents the results of air flow and
heat transfer in a light weight automobile engine, considering fins with dimple to increase the heat transfer rate.
An analysis has been using ANSYS WORKBENCH version 12.0 was conducted to find the optimum number of
dimples to maximizing the heat transfer across the Automobile engine body. The results indicate that the
presence of fins with dimple shows improved results on the basis of heat transfer.
This document summarizes a study on improving the cooling efficiency of fins in a two-stage reciprocating compressor through finite element analysis and dimensional modification. The existing annular fins are made of aluminum alloy. A finite element model of the fins is created in ANSYS to analyze temperature distribution over time under natural convection conditions. The results show the fins reach room temperature in 30 minutes. The fins are then modified by increasing the number of fins from 11 to 13. Finite element analysis of the modified fins shows cooling time is reduced to 22 minutes. In conclusion, modifying the fin geometry through additional fins improves the cooling rate of the reciprocating compressor.
The document summarizes the fabrication and testing of a heat exchanger test rig. Key points:
- The test rig was designed and built to study a counter-flow tube heat exchanger using aluminum sheets and tubes.
- Finite element analysis was performed on the rig design to analyze stresses. Water was heated to 40°C and pumped through one side while tap water entered the other side.
- Effectiveness-NTU method was used to calculate theoretical outlet temperatures which were compared to experimental readings to determine error percentages.
The overall convection heat transfer coefficients for long horizontal rectangular fin
arrays are low because the surfaces in the inner region are poorly ventilated. In this
study, perforations through the fin base are introduced to improve ventilation with
cold air from below the fin base. Aluminum fin arrays with length L= 380mm, fin
height H = 38mm, fin thickness tf = 1mm, and fin spacing S = 10mm are analyzed
experimentally and numerically using ANSYS 14.0 so as to obtain the temperature
distribution along the fin height and fin length. In this work the fin array
configurations are tested experimentally with two different heater input as 50W and
65W. The heat transfer coefficient for fin array with perforations in fin base increased
by the enhancement factor of 1.49 and
1.42 as compared to fin array without perforation with 50W and 65W heater input
respectively. The heat transfer coefficient for the same fin configuration is also
increased with increase in heater input from 50W to 65W. Experimental and
numerical results for the temperature distribution show a difference of 5-9%. The
distribution of heat flux obtained with ANSYS 14.0 quantitatively follows the trend of
the same reported in the literature review.
HEAT TRANSFER CO EFFICIENT VS HEAT FLOW RATE BY FORCED CONVECTIONTajammul Kamal
This document is a project report submitted by a student for their diploma in petrochemical engineering. It investigates heat transfer coefficients and heat flow rates through forced convection. Specifically, it looks at optimizing the design of heat sinks by considering factors like fin shape, thickness, spacing, and their effects on thermal resistance and heat dissipation. It provides background on previous related studies and the importance of heat transfer in applications like electronics cooling. The goal is to develop equations to determine the optimum specifications of fins in a heat sink based on parameters like the Biot number, heat transfer coefficient, and fin shape.
CFD Simulation of Thermo Acoustic CoolingIRJEETJournal
Thermo-acoustic Refrigerators use acoustic power for generating cold temperatures. Development of refrigerators based on thermos-acoustic technology is a novel solution to the present day need of cooling, without causing environmental hazards. With added advantages like minimal moving parts and absence of CFC refrigerants, these devices can attain very low temperatures maintaining a compact size. The present work describes an in-depth theoretical analysis of standing wave thermos-acoustic refrigerators. This consists of detailed parametric studies, transient state analysis and a design using available simulation software. Design and construction of a thermos-acoustic refrigerator using a commercially available electro-dynamic motor is also presented.
Abstract: Heat pipe are high-efficient heat transfer devices and have been widely applied in various thermal systems. Since heat pipe utilize the phase change of the working fluid to transport the heat, the selection of working fluid is of essential importance to promote the thermal performance of heat pipe. Owing to the heat transfer enhancement effect of nanofluid in the single phase and phase change heat transfer, some researchers have applied various nanofluids in heat pipe as the working fluids to enhance their heat transfer performance.
Similar to A Thesis on Design Optimization of Heat Sink in Power Electronics (20)
An In-Depth Exploration of Natural Language Processing: Evolution, Applicatio...DharmaBanothu
Natural language processing (NLP) has
recently garnered significant interest for the
computational representation and analysis of human
language. Its applications span multiple domains such
as machine translation, email spam detection,
information extraction, summarization, healthcare,
and question answering. This paper first delineates
four phases by examining various levels of NLP and
components of Natural Language Generation,
followed by a review of the history and progression of
NLP. Subsequently, we delve into the current state of
the art by presenting diverse NLP applications,
contemporary trends, and challenges. Finally, we
discuss some available datasets, models, and
evaluation metrics in NLP.
This is an overview of my current metallic design and engineering knowledge base built up over my professional career and two MSc degrees : - MSc in Advanced Manufacturing Technology University of Portsmouth graduated 1st May 1998, and MSc in Aircraft Engineering Cranfield University graduated 8th June 2007.
Sachpazis_Consolidation Settlement Calculation Program-The Python Code and th...Dr.Costas Sachpazis
Consolidation Settlement Calculation Program-The Python Code
By Professor Dr. Costas Sachpazis, Civil Engineer & Geologist
This program calculates the consolidation settlement for a foundation based on soil layer properties and foundation data. It allows users to input multiple soil layers and foundation characteristics to determine the total settlement.
Data Communication and Computer Networks Management System Project Report.pdfKamal Acharya
Networking is a telecommunications network that allows computers to exchange data. In
computer networks, networked computing devices pass data to each other along data
connections. Data is transferred in the form of packets. The connections between nodes are
established using either cable media or wireless media.
A Thesis on Design Optimization of Heat Sink in Power Electronics
1. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 83|P a g e
A Thesis on Design Optimization of Heat Sink in Power
Electronics
P.Chennakesavarao1
P.Srihari2
M.E (Thermal Engg.) student, Aditya Institute of Technology and Management, Tekkali.
Associate.professor, Aditya Institute of Technology and Management, Tekkali.
ABSTRACT
The heat sinks are used in electronic systems to remove heat from the chip and effectively transfer it to the
ambient. The heat sink geometry is designed by the mechanical engineers with the primary aim of reducing the
thermal resistance of the heat sink for better cooling in the electronic systems. Due to the proximity of the heat
sink with the ICs, the RF fields created by RF currents in the ICs/PCBs gets coupled to heat sinks. Hence, the
coupled RF current can cause radiated emission. This radiated noise from the device can couple and disturb the
functioning of the nearby electronic systems. Also this radiated emission from the device poses a problem to the
system compliance with respect to EMI/EMC regulations. The international EMI/EMC standards require the
radiated emission from the electronic devices to be kept below the specified limits.
As a result the design of Heat Sink is very important factor for the efficient operation of the electronic
equipment. In this project design optimization of a Heat sink in a Power amplifier is performed to reduce the
weight and size .Power amplifier is electronic equipment mounted in an army vehicle. The power modules
inside the amplifier generates a heat of 1440 Watts and a temperature of 140 0c.Two Heat sinks are used to
dissipate the heat generated inside the equipment and maintain a temperature of less than 850c. The existing
heat sink which is being used is weighing around 10.3kgs and height of 51mm; as a result the unit is very robust.
The objective of my project is To design & optimize the heat sink to reduce the weight and size. The
optimized heat sink should also dissipate heat generated by power modules and maintain a temperature of less
than 850c inside. To achieve the design a steady state thermal analysis will be performed on the heat sink and
plot the Temperature distribution on the fins. Based on the above analysis results we will increase/decrease the
number of fins, thickness of fins, and height of fins to reduce the weight of the heat sink. We will perform CFD
analysis of the power amplifier by mounting the optimized heat sink and plot temperature, pressure and velocity
distribution in the power amplifier enclosure. Efforts are made to optimize temperature, pressure and velocity
distribution in the power amplifier enclosure by reorienting the power modules in the enclosure.
UNIGRAPHICS software is used for 3D modeling SOLID WORKS FLOW SIMULATION software is used
for thermal and CFD analysis.
Key words: RF currents: Radio Frequency currents EMI/EMC: Electromagnetic interference/ Electromagnetic
compatibility
I. INTRODUCTION
1.1 INTRODUCTION TO HEAT SINK
The heat sink is a very important component in
cooling design. It increases the component surface
area significantly while usually increasing the heat
transfer coefficient as well. Thus, the total resistance
from the component junction to the surroundings is
reduced significantly, which in turn reduces the
junction temperature within a device. As a result,
obtaining correct performance characteristics for heat
sinks is extremely important in cooling design
solution.
1.1.1 HEAT SINK TYPES
Heat sinks can be classified in terms of manufacturing
methods and their final form shapes. The most
common types of air-cooled heat sinks include:
Stampings: Copper or aluminium sheet metals are
stamped into desired shapes. they are used in
traditional air cooling of electronic components and
offer a low cost solution to low density thermal
problems. They are suitable for high volume
production, because advanced tooling with high speed
stamping would lower costs. Additional labor-saving
options, such as taps, clips, and interface materials,
can be factory applied to help to reduce the board
assembly costs.
Extrusion: These allow the formation of elaborate
two-dimensional shapes capable of dissipating large
heat loads. They may be cut, machined, and options
added. A cross-cutting will produce omni-directional,
rectangular pin fin heat sinks, and incorporating
serrated fins improves the performance by
RESEARCH ARTICLE OPEN ACCESS
2. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 84|P a g e
approximately 10 to 20%, but with a slower extrusion
rate. Extrusion limits, such as the fin height-to-gap fin
thickness, usually dictate the flexibility in design
options. Typical fin height-to-gap aspect ratio of up to
6 and a minimum fin thickness of 1.3mm, are
attainable with a standard extrusion. A 10 to 1 aspect
ratio and a fin thickness of 0.8″can be achieved with
special die design features. However, as the aspect
ratio increases, the extrusion tolerance is
compromised.
Bonded/Fabricated Fins: Most air cooled heat sinks
are convection limited, and the overall thermal
performance of an air cooled heat sink can often be
improved significantly if more surface area can be
exposed to the air stream. These high performance
heat sinks utilize thermally conductive aluminium-
filled epoxy to bond planar fins onto a grooved
extrusion base plate. This process allows for a much
greater fin height-to-gap aspect ratio of 20 to40,
greatly increasing the cooling capacity without
increasing volume requirements.
Castings: Sand, lost core and die casting processes are
available with or without vacuum assistance, in
aluminium or copper/bronze. This technology is used
in high density pin fin heat sinks which provide
maximum performance when using impingement
cooling.
Folded Fins: Corrugated sheet metal in either
aluminium or copper increases surface area and,
hence, the volumetric performance. The heat sink is
then attached to either a base plate or directly to the
heating surface via epoxying or brazing. It is not
suitable for high profile heat sinks on account of the
availability and fin efficiency. Hence, it allows high
performance heat sinks to be fabricated for
applications. The objectives of these experiments are
to evaluate the performance of heat sinks, determine
the effect of flow velocity, and to analyze results by
comparing them.
1.2 THEORY:
A heat sink works by conducting heat through its base
and fins and then converting it to the surroundings.
The equation for thermal resistance of a heat sink is
shown in Equation (1)
... ... (1)
The thermal resistance can be found from
experimental testing, simulation, or manufacturer’s
data. In this lab, you will be using Equation (1) to find
heat sink resistance and comparing results to
published correlations.
The heat sink resistance includes both the conduction
and convection resistance, although the convection
resistance typically dominates. Equation (2) is a
somewhat simplified equation for the heat sink
resistance. This equation would be completely
accurate if conduction and convection were in parallel.
However, this is not completely the case for heat
sinks, so this equation incorporates some inaccuracies.
... ... (2)
Conduction resistance can be lowered by changing the
geometry and choosing a material with a higher
thermal conductivity. Convection resistance can be
lowered by increasing the heat sink surface area or the
heat transfer coefficient. The heat transfer coefficient
will change with both geometry and flow velocity for
a given fluid type.
More commonly, heat sink resistance is found using
the equation for fin resistance given below.
... ... (3)
Here ηf, the fin efficiency, takes into account the
conduction resistance and is equal to the actual fin
heat transfer divided by the fin heat transfer if it were
to have been all at the heat sink base temperature. The
heat sink resistance becomes
... ... (4)
where
ηo=1-NAfin(1-ηf)/Atot
... ... (5)
Here ηo is the overall surface efficiency, N the number
of fins, and Atot the total heat sink surface area.
1.3 HEAT TRANSFER PRINCIPLE
A heat sink transfers thermal energy from a higher
temperature to a lower temperature fluid medium. The
fluid medium is frequently air, but can also be water or
in the case of heat exchangers, refrigerants and oil. If
the fluid medium is water, the 'heat sink' is frequently
called a cold plate. In thermodynamics a heat sink is
a heat reservoir that can absorb an arbitrary amount of
heat without significantly changing temperature.
Practical heat sinks for electronic devices must have a
temperature higher than the surroundings to transfer
heat by convection, radiation, and conduction.
To understand the principle of a heat sink,
consider Fourier's law of heat conduction. Joseph
Fourier was a French mathematician who made
important contributions to the analytical treatment of
heat conduction. Fourier's law of heat conduction,
simplified to a one-dimensional form in the x-
direction, shows that when there is a temperature
gradient in a body, heat will be transferred from the
higher temperature region to the lower temperature
region. The rate at which heat is transferred by
conduction, , is proportional to the product of the
temperature gradient and the cross-sectional area
through which heat is transferred.
3. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 85|P a g e
... ... (6)
Figure 1.1: Sketch of a heat sink in a duct used to
calculate the governing equations from conservation
of energy and Newton’s law of cooling
Consider a heat sink in a duct, where air flows through
the duct, as shown in Figure 1.1. It is assumed that the
heat sink base is higher in temperature than the air.
Applying the conservation of energy, for steady-state
conditions, and Newton’s law of cooling to the
temperature nodes shown in Figure 1.1 gives the
following set of equations.
… … (7)
… … (8)
Where
…. …(9)
Using the mean air temperature is an assumption that
is valid for relatively short heat sinks. When compact
heat exchangers are calculated, the logarithmic mean
air temperature is used. is the air mass flow rate in
kg/s.
The above equations show that
When the air flow through the heat sink
decreases, this results in an increase in the
average air temperature. This in turn increases
the heat sink base temperature. And additionally,
the thermal resistance of the heat sink will also
increase. The net result is a higher heat sink base
temperature.
The increase in heat sink thermal resistance with
decrease in flow rate will be shown in later in
this article.
The inlet air temperature relates strongly with
the heat sink base temperature. For example, if
there is recirculation of air in a product, the inlet
air temperature is not the ambient air
temperature. The inlet air temperature of the heat
sink is therefore higher, which also results in a
higher heat sink base temperature.
If there is no air flow around the heat sink,
energy cannot be transferred.
A heat sink is not a device with the "magical
ability to absorb heat like a sponge and send it
off to a parallel universe".
Natural convection requires free flow of air over the
heat sink. If fins are not aligned vertically, or if pins
are too close together to allow sufficient air flow
between them, the efficiency of the heat sink will
decline.
II.OBJECTIVE AND METHODOLOGY
2.1 PROBLEM DEFINITION:
The heat sinks are used in electronic systems to
remove heat from the chip and effectively transfer it to
the ambient. The heat sink geometry is designed by
the mechanical engineers with the primary aim of
reducing the thermal resistance of the heat sink for
better cooling in the electronic systems.
In the present project Design optimization of a Heat
sink in a Power amplifier is performed to reduce the
weight and size. Power amplifier is electronic
equipment mounted in an army vehicle. The power
modules inside the amplifier generates a heat of 1440
Watts and a temperature of 160 0c.Two Heat sinks are
used to dissipate the heat generated inside the
equipment and maintain a temperature of less than
850c. The existing heat sink which is being used is
weighing around 10.3kgs and height of 53mm, as a
result the unit is very robust.
The objective of my project is
To design & optimize the heat sink to reduce the
weight and size.
The optimized heat sink should also dissipate heat
generated by power modules and maintain a
temperature of less than 850c inside.
To achieve the design a steady state thermal analysis
will be performed on the heat sink and plot the
Temperature distribution on the fins.
Based on the above analysis results we will
increase/decrease the number of fins, thickness of fins,
and height of fins to reduce the weight of the heat
sink.
We will perform CFD analysis of the power amplifier
by mounting the optimized heat sink and plot
temperature, pressure and velocity distribution in the
power amplifier enclosure.
Efforts are made to optimize temperature, pressure and
velocity distribution in the power amplifier enclosure
by reorienting the power modules in the enclosure
UNIGRAPHICS software is used for 3D modeling
SOLID WORKS FLOW SIMULATION
software is used for thermal and CFD analysis.
4. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 86|P a g e
2.2 METHODOLOGY:
A 3D model of the existing heat sink was created
using UNIGRAPHICS NX.
The 3D model is converted into parasolid file and
imported into SOLID WORKS FLOW
SIMULATION.
Steady state thermal analysis was carried out on
the existing heat sink. The heat generation of
individual heat modules is applied on the heat
sink. The CFM of the fan is applied as convection
for the heat sink.
Based on the above thermal results, the existing
heat sink is optimized for size and weight.
The Optimized heat sink is mounted in the power
amplifier enclosure and CFD analysis is carried
out to plot the temperature, pressure and velocity
distribution in the power amplifier enclosure.
Based on the above CFD analysis, the power
modules are reoriented from zero convection
areas to the convection areas to reduce the
temperature.
III. 3D MODELING OF POWER
AMPLIFIER
3.1 INTRODUCTION TO UNIGRAPHICS
The power amplifier assembly is an electronic
enclosure used in army vehicles to amplify the signals.
Some of the important and functional parts of the
power amplifier include heat sinks, power modules
and fans. The 3D model of the power amplifier
assembly is created using UNIGRAPHICS NX
software from the 2d drawings. UNIGRAPHICS NX
is the world’s leading 3D product development
solution. This software enables designers and
engineers to bring better products to the market faster.
It takes care of the entire product definition to
serviceability. NX delivers measurable value to
manufacturing companies of all sizes and in all
industries. NX is used in a vast range of industries
from manufacturing of rockets to computer
peripherals. With more than 1 lakh seats installed in
worldwide many cad users are exposed to NX and
enjoy using NX for its power and capability.
3.2 CREATING A SOLID MODEL
Modeling provides the design engineer with intuitive
and comfortable modeling techniques such as
sketching, feature based modeling, and dimension
driven editing. An excellent way to begin a design
concept is with a sketch. When you use a sketch, a
rough idea of the part becomes represented and
constrained, based on the fit and function requirements
of your design. In this way, your design intent is
captured. This ensures that when the design is passed
down to the next level of engineering, the basic
requirements are not lost when the design is edited.
The strategy you use to create and edit your model to
form the desired object depends on the form and
complexity of the object. You will likely use several
different methods during a work session. The next
several figures illustrate one example of the design
process, starting with a sketch and ending with a
finished model. First, you can create a sketch
"outline" of curves. Then you can sweep or rotate
these curves to create a complex portion of your
design.
3.3 ASSEMBLY CONCEPTS
Components
Assembly part files point to geometry and features in
the subordinate parts rather than creating duplicate
copies of those objects at each level in the assembly.
This technique not only minimizes the size of
assembly parts files, but also provides high levels of
associativity. For example, modifying the geometry of
one component causes all assemblies that use that
component in the session to automatically reflect that
change. Some properties, such as translucency and
partial shading (on the Edit Object Display dialog),
can be changed directly on a selected component.
Other properties are changed on selected solids or
geometry within a component. Within an assembly, a
particular part may be used in many places. Each
usage is referred to as a component and the file
containing the actual geometry for the component is
called the component part.
Top-down or Bottom-up Modeling
You are not limited to any one particular approach to
building the assembly. You can create individual
models in isolation, then later add them to assemblies
(bottom-up), or you can create them directly at the
assembly level (top-down). For example, you can
initially work in a top-down fashion, then switch back
and forth between bottom-up and top-down modeling.
Multiple Loaded Parts
Many parts can be simultaneously loaded at any given
time. These parts may have been loaded explicitly
(such as with the Assembly Navigator's Open
options), or implicitly as a result of being used by
some other loaded assembly. Loaded parts do not
have to belong to the same assembly. The part
currently displayed in the graphics window is called
the displayed part. You can make edits in parallel to
several parts by switching the displayed part back and
forth among those parts. The following figure shows
two different assembly parts (MOUNT_ASSY.PRT
and MOUNT2_ASSY.PRT) which both use many of
the same components. The difference in the two is
that due to a design change, assembly
MOUNT2_ASSY.PRT uses components BODY2 and
BUSHING2, which differ slightly from those used by
MOUNT_ASSY.PRT (BODY and BUSHING). The
remaining components are used by both assemblies.
The following scenario illustrates how component
parts used by multiple assemblies are loaded:
Before you open a file, there is no displayed
part or any loaded parts.
5. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 87|P a g e
When you open MOUNT_ASSY.PRT,
component parts BOLT, BUSHING, BODY, NUT,
PIN, and YOKE are also loaded.
MOUNT_ASSY.PRT becomes the displayed part and
the work part. If you then open
MOUNT2_ASSY.PRT, only the component parts not
also used by the previously opened assembly
(BODY2 and BUSHING2) are loaded.
MOUNT2_ASSY.PRT then becomes the displayed
part and work part.
You could also open up a third assembly part
that does not share any common components with the
previously opened files. The new assembly part and
all component parts it uses are then loaded, and the
new assembly part becomes the displayed part and
work part
Design in Context
When the displayed part is an assembly, it is possible
to change the work part to any of the components
within that assembly (except for unloaded parts and
parts of different units). Geometry features, and
components can then be added to or edited within the
work part. Geometry outside of the work part can be
referenced in many modeling operations. For
example, control points on geometry outside of the
work part can be used to position a feature within the
work part. When an object is designed in context, it is
added to the reference set used to represent the work
part.
Associativity Maintained
Geometric changes made at any level within an
assembly result in the update of associated data at all
other levels of affected assemblies. An edit to an
individual piece part causes all assembly drawings
that use that part to be updated appropriately.
Conversely, an edit made to a component in the
context of an assembly results in the update of
drawings and other associated objects (such as tool
paths) within the component part. See the next two
figures for examples of top-down and bottom-up
updates.
Mating Conditions
Mating conditions let you position components in an
assembly. This mating is accomplished by specifying
constraint relationships between two components in
the assembly. For example, you can specify that a
cylindrical face on one component is to be coaxial
with a conical face on another component. You can
use combinations of different constraints to
completely specify a component's position in the
assembly. The system considers one of the
components as fixed in a constant location, then
calculates a position for the other component which
satisfies the specified constraints. The relationship
between the two components is associative. If you
move the fixed component's location, the component
that is mated to it also moves when you update. For
example, if you mate a bolt to a hole, if the hole is
moved, the bolt moves with it.
Fig.3.1 shows 3D model of the Power amplifier
Assembly structure with heat sinks and power
modules.
Fig.3.2 shows front view of 3d model of Power
amplifier
Assembly
structure
Fig.3.3 shows rear view of Power amplifier assembly
6. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 88|P a g e
Fig.3.4 shows power amplifier Assembly structure
with power modules
Fig.3.5 shows power modules and heat sinks in power
amplifier assembly
Fig.3.6 shows the heat sinks used in power amplifier
assembly enclosure
Fig.3.7 shows the detailed view of heat sinks in power
amplifier used for analysis
IV.THERMAL ANALYSIS OF HEAT SINK
4.1 INTRODUCTION
SOLIDWORKS FLOWSIMULATION is
general-purpose finite element analysis (FEA)
software package. Finite Element Analysis is a
numerical method of deconstructing a complex
system into very small pieces (of user-designated size)
called elements. The software implements equations
that govern the behaviour of these elements and
solves them all; creating a comprehensive explanation
of how the system acts as a whole. These results then
can be presented in tabulated, or graphical forms.
This type of analysis is typically used for the design
and optimization of a system far too complex to
analyze by hand. Systems that may fit into this
category are too complex due to their geometry, scale,
or governing equations.
SOLIDWORKS FLOWSIMULATION is the
standard FEA teaching tool within the Mechanical
Engineering Department at many colleges.
SOLIDWORKS FLOW SIMULATION provides a
cost-effective way to explore the performance of
products or processes in a virtual environment. This
type of product development is termed virtual
prototyping.
With virtual prototyping techniques, users can iterate
various scenarios to optimize the product long before
the manufacturing is started. This enables a reduction
in the level of risk, and in the cost of ineffective
designs. The multifaceted nature of SOLIDWORKS
FLOW SIMULATION also provides a means to
ensure that users are able to see the effect of a design
on the whole behavior of the product, be it
electromagnetic, thermal, mechanical etc.
A thermal analysis calculates the temperature
distribution and related thermal quantities in a system
or component. Typical thermal quantities of interest
are:
The temperature distributions
The amount of heat lost or gained
Thermal gradients
Thermal fluxes.
7. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 89|P a g e
Thermal simulations play an important role in the
design of many engineering applications, including
internal combustion engines, turbines, heat
exchangers, piping systems, and electronic
components. In many cases, engineers follow a
thermal analysis with a stress analysis to calculate
thermal stresses (that is, stresses caused by thermal
expansions or contractions).
4.2 THERMAL ANALYSIS
SOLIDWORKS FLOWSIMULATION supports two
types of thermal analysis:
1. A steady-state thermal analysis determines the
temperature distribution and other thermal
quantities under steady-state loading conditions.
A steady-state loading condition is a situation
where heat storage effects varying over a period
of time can be ignored.
2. A transient thermal analysis determines the
temperature distribution and other thermal
quantities under conditions that vary over a period
of time
We can use steady-state thermal analysis to determine
temperatures, thermal gradients, heat flow rates, and
heat fluxes in an object that are caused by thermal
loads that do not vary over time. Such loads include
the following:
Convections
Radiation
Heat flow rates
Heat fluxes (heat flow per unit area)
Heat generation rates (heat flow per unit volume)
Constant temperature boundaries
A steady-state thermal analysis may be either linear,
with constant material properties; or nonlinear, with
material properties that depend on temperature. The
thermal properties of most material do vary with
temperature, so the analysis usually is nonlinear.
Including radiation effects also makes the analysis
nonlinear. Transient calculations are time dependent
and SOLIDWORKS FLOWSIMULATION can both
solve distributions as well as create video for time
incremental displays of models.
3D model of the amplifier developed using
UNIGRAPHICS:
2 fans of CFM
Fig.4.1 The above figure shows the Enclosure of the
power amplifier
Fig.4.2 The above figure shows the components inside
the Enclosure of the power amplifier
Duct created for
passage of air to
the heat sinks
8. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 90|P a g e
Fig. 4.3 The above figure shows the heat modules
inside the Enclosure of the power amplifier
The original heat sink shown above is weighing
around 10.3 Kgs as the result the power amplifier unit
becomes robust. The objective of my project is to
reduce the weight of the heat sink and at the same time
the heat generated inside the amplifier must be less
than 85 degrees.
Steady state thermal analysis is carried out using
SOLIDWORKS FLOWSIMULATION software to
find the temperature distribution on the original heat
sink.
4.3 THERMAL ANALYSIS OF ORIGINAL
HEAT SINK :
The specifications of the original heat sink are as
follows:
Weight of the heat sink=10.3 Kgs
Fin height = 46 mm
Base plate Thickness = 5 mm
Number of fins = 51
Thickness of fin = 3mm
Fig. 4.4 The above figure shows the Details of fins in
the heatsink
Material Properties:
The heat sink is made up of Aluminium 6061 Alloy
material. Forced convection is applied by using 2 fans
of 300 CFM each. The analysis is carried out at worst
atmospheric temperature of 55 degrees.
Thermal conductivity of Aluminium = 167 W/mk
Film coefficient (air) = 26.4 w/m2k (Assumed 2 fans
with 300 CFM each)
Bulk temperature = 328 K (55 c)
The below formulae is used to calculate film
coefficient of air.
Boundary Conditions:
Heat Generation values from the heat sources are
appled as volume sources on the heat modules and
convection film coefficient is applied on the fin
surfcaes of heat sink.The below table lists the heat
generated by individual module.The below figures
shows the heat generations applied and the convection
applied on the heat sink.
Fig.4.5 shows the heat generation values applied on
modules of the heat sink.
9. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 91|P a g e
Fig.4.6 shows the convection applied on the fin
surfaces of heat sink
V. Results:
From the thermal analysis the maximum temperature
observed on the existing heat sink is 356 k (83
degrees)
Fig. 5.1 Shows Temperature distribution from
Thermal analysis for existing heat sink
Fig.5.2 shows the temperature distribution for existing
heat sink
Fig.5.3 shows the temperature distribution along the
cross section of the existing heat sink
Fig.5.4 shows the temperature distribution along the
cross section of the existing heat sink
Fig.5.5 shows the temperature distribution on the tip
of the fin for existing heat sink
From The above results it is observed that:
Maximum temperature observed at heat
generation patches is 356 K (83 0C)
Max temp observed at tip of fin is 341 K (68
0C)
From the results it is observed that the though the
maximum temperature is within the design limit, the
temperature has not reached the tip of the fin. So the
fin height can be reduced to reduce the weight. The
10. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 92|P a g e
below table shows the summary of specifications and
temperature obtained on the original heat sink.
S.No
Description Original
1
Weight (Kgs) 10.3
2
Base plate thickness (mm) 5
3
Fin Height (mm) 46
4
Number of Fins 51
5
Fin thickness (mm) 3
6
Temperature observed (K) 356
Table: Summary of results for original heat sink
VI. RESULTS AND DISCUSSIONS
In the present project Design optimization of a
Heat sink in a Power amplifier is performed to reduce
the weight and size. Power amplifier is electronic
equipment mounted in an army vehicle. Two Heat
sinks are used to dissipate the heat generated inside the
equipment and maintain a temperature of less than
850c. The existing heat sink which is being used is
weighing around 10.3kgs and height of 53mm, as a
result the unit is very robust. In order to reduce weight
of the heat sink and maintain temperature below
850c,three modified heat sinks are designed and
thermal analysis is carried out. As CFD analysis is
very expensive in terms of time and resources, initially
thermal analysis is performed on the heat sink. After
concluding the optimised heat sink, a CFD analysis is
done to find the temperature, pressure and velocity of
fluid inside the enclosure. The comparison table of
results and specifications of original and modified heat
sinks are tabulated below. The comparison graphs are
also plotted below.
Table 6.1: Comparison table of original and modified
heat sinks
Graph 1: Comparison weights for original and
modified heat sinks
Graph 2: Comparison of number of fins for original
and modified heat sinks
Graph 3: Comparison of fin thickness for original and
modified heat sinks
Heat Sink
S.No
Description Original Modified#1
Modified
#2
Modified
#3
1 Weight (Kgs) 10.3 8.6 3.6 3.9
2
Base plate
thickness
(mm)
5 5
5 5
3
Fin Height
(mm)
46 46
24 24
4
Number of
Fins
51 51
51 67
5
Fin thickness
(mm)
3 3
3 2
6
Temperature
observed (K)
356 392
364 350
11. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 93|P a g e
Graph 4: Comparison of temperatures observed for
original and modified heat sinks
The following observations are made from the CFD
analysis of the enclosure:
1. Sufficient amount of fluid flow is observed
in the fin region.
2. The maximum temperature observed is 349 k
(76 0C) in the enclosure.
3. New heat sink design helped in reducing
temperatures.
4. Max pressure difference observed is 618 pa
between inlet and outlet.
5. Max temperature of the fluid observed ~ 67
C at fins region.
VII. CONCLUSIONS AND FUTURE SCOPE
In this project the Heat sink of the power
amplifier has been optimized for more heat transfer,
less weight and less pressure drop using CFD analysis.
The heat sink is mounted in the power amplifier on
which different electronic components are mounted
which dissipates heat.
Steady state thermal analysis has been
done for 4 models of heat sink.(1
original heat sink and 3 modified heat
sink models)
Max temperature on the original heat
sink is 83 0c and weight of the of the
heat sink is 10.3 Kgs.
Max temperature on the modified
model#1 heat sink is 119 0c and
weight of the of the heat sink is 8.6
Kgs i.e. a mass reduction of 16.5%.
Max temperature on the modified
model#2 heat sink is 91 0c and weight
of the of the heat sink is 3.6 Kgs i.e. a
mass reduction of 65%.
Max temperature on the modified
model#3 heat sink is 77 0c and weight
of the of the heat sink is 3.9 Kgs i.e. a
mass reduction of 62%.
The CFD analysis of the power amplifier has been
carried out by mounting the optimized heat sink
model#3.From the CFD analysis it is observed that
Max pressure difference observed is 618 Pa between
inlet and outlet. The maximum temperature on the heat
sink observed is 76o C.The weight of the heat sink is
also reduced to 3.9 Kgs. From the analysis it is
concluded that the power amplifier with modified
model#3 heat sink is the best design in terms of weight
and heat transfer.
Future Scope: As the power amplifier is used in
defense equipment it is subjected to structural loads.
Structural analysis has to be carried out to check the
integrity of the power amplifier for structural loads.
REFERENCES
[1.] Takeshi Hirasawa, Kenya Kawabata and
Masaru Oomi “Evolution of the Heatsink
Technology” Furukawa Review, No. 27 2005.
[2.] Nikhil Seshasayee “Understanding Thermal
Dissipation and Design of a Heatsink”. Texas
Instruments Incorporated SLVA462–May
2011.
[3.] Stephen D. Turner, and Ahmed M. Zaghlol,
had presented a paper on “Thermal Design
Techniques improve Solid State Power
Amplifier Performance”.
[4.] Mahendra Wankhede, Vivek Khaire, Dr.
Avijit Goswami and Prof. S. D. Mahajan,
“evaluation of cooling solutions for outdoor
electronics”.
[5.] Hussam Jouhara and Brian P. Axcell
“Modelling and Simulation Techniques for
Forced Convection Heat Transfer in Heat
Sinks with Rectangular Fins”.
[6.] Behnia, M., Copeland, D., and Soodphadakee,
D., 1998, “A Comparison of Heat Sink
Geometries for Laminar Forced Convection,”
Proceedings of The Sixth Intersociety
Conference on Thermal and Thermo
mechanical Phenomena in Electronic Systems,
Seattle, Washington, USA, May 27–30, pp.
310–315.
[7.] Majid Bahrami, Golnoosh Mostafavi, Mehram
Ahmad., “Effects of geometrical parameters
on natural convective heat transfer from
vertically mounted rectangular interrupted
fins” jul 8-12, 2012, Rio Grande, Puerto Rico.
ASME 2012.
[8.] Charles D. Jones and Lester F. Smith
“OPTIMAL ARRANGEMENT OF
RECTANGULAR FINS ON HORIZONTAL
SURFACE FOR FREE CONVECTION
HEAT TRANSFER”. Journal of heat transfer
volume 92 Online August 11, 2010.
[9.] Schmidt R., Chu R., Kamath V., Ellsworth M.,
Iyengar M., Porter D., Lehman B.,
12. P.Chennakesavarao Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 10( Part - 5), October 2014, pp.83-94
www.ijera.com 94|P a g e
“Maintaining Datacomm rack Inlet
Temperatures with water Cooled heat
Exchangers”, Proceedings of the Pacific
Rim/ASME International Electronic
Packaging Technical Conference
(INTERpack), Paper number IPACK2005-
73468, San Francisco, California, July 2005.
[10.] Shin, D., 1998, “Thermal Design and
Evaluation Methods for Heat Sink”, Tech.
Report. 7th International FLOTHERM User
Conference Verona, Italy - T226 .
[11.] Shah, R.K., and Bhatti, M.S., 1987, “Laminar
Convective Heat Transfer in Ducts”, in Kakaç,
S., Shah, R.K., and Aung, W., Handbook of
Single-Phase Convective Heat Transfer”, John
Wiley & Sons, p. 3.42.
[12.] M. E. Steinke and S. G. Kandlikar, “Single-
phase heat transfer enhancement techniques in
micro channel 17–19, 2004, pp. 141–148and
mini channel flows,” in Proc. 2nd Int. Conf.
Micro channels Mini channels, Rochester,
NY, Jun.