-
Eliminating the spin-down critical angle in polarizing neutron optics for expanding the polarization bandwidth
Authors:
A. Zubayer,
N. Ghafoor,
A. Glavic,
J. Stahn,
M. Lorentzon,
A. Le Febvrier,
P. Eklund,
J. Birch,
F. Eriksson
Abstract:
Polarized neutron scattering is a very important analysis technique for studies of magnetism, spintronics, and high-sensitivity measurements, among others, offering invaluable information. Yet, the efficiency of such experiments rely on the performance of the polarizing neutron optics to provide high reflectivity and polarization. Presently, state-of-the-art polarizers like Fe/Si supermirrors are…
▽ More
Polarized neutron scattering is a very important analysis technique for studies of magnetism, spintronics, and high-sensitivity measurements, among others, offering invaluable information. Yet, the efficiency of such experiments rely on the performance of the polarizing neutron optics to provide high reflectivity and polarization. Presently, state-of-the-art polarizers like Fe/Si supermirrors are not able to polarize neutrons at low scattering angles in a monochromatic beam or able to polarize neutrons with a variety of wavelengths as for a non-monochromatic beam. To overcome this limitation, it is suggested to use Co/Ti multilayers on Ti substrates owing to their favorable scattering length density characteristics. It is shown that this approach enables a wavelength bandwidth several times larger than achievable with state-of-the-art materials on Si or glass substrates. Consequently, enabling the possibility of polarizing neutrons across an extended wavelength range, including those with very high wavelengths.
△ Less
Submitted 7 April, 2024;
originally announced April 2024.
-
Neutron optical tuning of Fe/11B4CTi multilayers for optimal polarization and increased reflectivity for polarizing neutron optics
Authors:
A. Zubayer,
N. Ghafoor,
K. A. Thorarinsdottir,
A. Glavic,
J. Stahn,
G. Nagy,
A. Vorobiev,
F. Magnus,
J. Birch,
F. Eriksson
Abstract:
The concept of scattering length density tuning for improved polarization is investigated for Fe/11B4CTi multilayers and compared to the commonly used Fe/Si system in polarizing multilayer neutron optics. X-ray and neutron reflectivity, magnetization, and neutron polarization have been measured on such multilayers, highlighting differences from conventional Fe/Si multilayers. The multilayer system…
▽ More
The concept of scattering length density tuning for improved polarization is investigated for Fe/11B4CTi multilayers and compared to the commonly used Fe/Si system in polarizing multilayer neutron optics. X-ray and neutron reflectivity, magnetization, and neutron polarization have been measured on such multilayers, highlighting differences from conventional Fe/Si multilayers. The multilayer systems were deposited with 25 Å period thickness, a layer thickness ratio of 0.35 and 20 periods, using ion-assisted DC magnetron sputtering. Replacing Si with 11B4CTi for these multilayers showed an increase in reflectivity due to a reduction in interface width. By tuning the ratio between 11B4C and Ti in the non-magnetic layers, a broad range of scattering length density values was achieved, facilitating scattering length density contrast matching between layers for spin-down neutrons, thereby enhancing polarization. These findings demonstrate the potential of Fe/11B4CTi multilayers as a promising option for polarizing neutron optics and highlight the concept of scattering length density tuning in a large range using 11B4CTi.
△ Less
Submitted 5 April, 2024;
originally announced April 2024.
-
Reflective, polarizing, and magnetically soft amorphous Fe/Si multilayer neutron optics with isotope-enriched 11B4C inducing atomically flat interfaces
Authors:
A. Zubayer,
N. Ghafoor,
K. A. Thórarinsdóttir,
S. Stendahl,
A. Glavic,
J. Stahn,
G. Nagy,
G. Greczynski,
M. Schwartzkopf,
A. Le Febvrier,
P. Eklund,
J. Birch,
F. Magnus,
F. Eriksson
Abstract:
The utilization of polarized neutrons is of great importance in scientific disciplines spanning materials science, physics, biology, and chemistry. Polarization analysis offers insights into otherwise unattainable sample information such as magnetic domains and structures, protein crystallography, composition, orientation, ion-diffusion mechanisms, and relative location of molecules in multicompon…
▽ More
The utilization of polarized neutrons is of great importance in scientific disciplines spanning materials science, physics, biology, and chemistry. Polarization analysis offers insights into otherwise unattainable sample information such as magnetic domains and structures, protein crystallography, composition, orientation, ion-diffusion mechanisms, and relative location of molecules in multicomponent biological systems. State-of-the-art multilayer polarizing neutron optics have limitations, particularly low specular reflectivity and polarization at higher scattering vectors/angles, and the requirement of high external magnetic fields to saturate the polarizer magnetization. Here, we show that by incorporating 11B4C into Fe/Si multilayers, amorphization and smooth interfaces can be achieved, yielding higher neutron reflectivity, less diffuse scattering and higher polarization. Magnetic coercivity is eliminated, and magnetic saturation can be reached at low external fields (>2 mT). This approach offers prospects for significant improvement in polarizing neutron optics, enabling; nonintrusive positioning of the polarizer, enhanced flux, increased data accuracy, and further polarizing/analyzing methods at neutron scattering facilities.
△ Less
Submitted 15 August, 2023;
originally announced August 2023.
-
Phase Reconstruction of a Cu(001) Seed Layer from $\textit{in situ}$ Polarized Neutron Reflectometry Data using Fe Reference Layers
Authors:
Alexander Book,
Sina Mayr,
Jochen Stahn,
Peter Böni,
Wolfgang Kreuzpaintner
Abstract:
The reconstruction of the complex reflection coefficient obtained by in situ Polarized Neutron Reflectometry is presented. Using the reference layer method, with a magnetic Fe layer, the phase information of the underlying Cu(001) seed layer sample structure is successfully retrieved and its scattering length density is calculated and compared with results obtained from traditional fitting. Two di…
▽ More
The reconstruction of the complex reflection coefficient obtained by in situ Polarized Neutron Reflectometry is presented. Using the reference layer method, with a magnetic Fe layer, the phase information of the underlying Cu(001) seed layer sample structure is successfully retrieved and its scattering length density is calculated and compared with results obtained from traditional fitting. Two different reference layer approaches for retrieving the phase information are compared.
△ Less
Submitted 15 November, 2021; v1 submitted 19 February, 2021;
originally announced February 2021.
-
Study of Reactively Sputtered Nickel Nitride Thin Films
Authors:
Nidhi Pandey,
Mukul Gupta,
Jochen Stahn
Abstract:
Nickel nitride (Ni-N) thin film samples were deposited using reactive magnetron sputtering process utilizing different partial flow of N2 (RN2). They were characterized using x-ray reflectivity (XRR), x-ray diffraction (XRD) and x-ray absorption near edge spectroscopy (XANES) taken at N K-edge and Ni L-edges. From XRR measurements, we find that the deposition rate and the density of Ni-N films dec…
▽ More
Nickel nitride (Ni-N) thin film samples were deposited using reactive magnetron sputtering process utilizing different partial flow of N2 (RN2). They were characterized using x-ray reflectivity (XRR), x-ray diffraction (XRD) and x-ray absorption near edge spectroscopy (XANES) taken at N K-edge and Ni L-edges. From XRR measurements, we find that the deposition rate and the density of Ni-N films decrease due to successively progression in RN2, signifying that Ni-N alloys and compounds are forming both at Ni target surface and also within the thin film samples. The crystal structure obtained from XRD measurements suggest an evolution of different Ni-N compounds given by: Ni, Ni(N), Ni4N, Ni3N, and Ni2N with a gradual rise in RN2. XANES measurements further confirm these phases, in agreement with XRD results. Polarized neutron reflectivity measurements were performed to probe the magnetization, and it was found Ni-N thin films become non-magnetic even when N incorporation increases beyond few at%. Overall growth behavior of Ni-N samples has been compared with that of rather well-known Fe-N and Co-N systems, yielding similarities and differences among them.
△ Less
Submitted 22 April, 2020;
originally announced April 2020.
-
Controlling the strength of ferromagnetic order in YBa$_2$Cu$_3$O$_7$/La$_{2/3}$Ca$_{1/3}$MnO$_3$ multilayers
Authors:
R. de Andrés Prada,
R. Gaina,
N. Biškup,
M. Varela,
J. Stahn,
C. Bernhard
Abstract:
With dc magnetisation and polarized neutron reflectometry we studied the ferromagnetic response of YBa$_2$Cu$_3$O$_7$/La$_{2/3}$Ca$_{1/3}$MnO$_3$ (YBCO/LCMO) multilayers that are grown with pulsed laser deposition. We found that whereas for certain growth conditions (denoted as A-type) the ferromagnetic moment of the LCMO layer is strongly dependent on the structural details of the YBCO layer on w…
▽ More
With dc magnetisation and polarized neutron reflectometry we studied the ferromagnetic response of YBa$_2$Cu$_3$O$_7$/La$_{2/3}$Ca$_{1/3}$MnO$_3$ (YBCO/LCMO) multilayers that are grown with pulsed laser deposition. We found that whereas for certain growth conditions (denoted as A-type) the ferromagnetic moment of the LCMO layer is strongly dependent on the structural details of the YBCO layer on which it is deposited, for others (B-type) the ferromagnetism of LCMO is much more robust. Both kinds of multilayers are of similar structural quality, but electron energy-loss spectroscopy (EELS) studies with a scanning transmission electron microscope reveal an enhanced average Mn oxidation state of +3.5 for the A-type as opposed to the B-type samples for which it is close to the nominal value of +3.33. The related, additional hole doping of the A-type LCMO layers, which likely originates from La and/or Mn vacancies, can explain their fragile ferromagnetic order since it places them close to the boundary of the ferromagnetic order at which even weak perturbations can induce an antiferromagnetic or glassy state. On the other hand, we show that the B-type samples allow one to obtain YBCO/LCMO heterostructures with very thick YBCO layers and, yet, strongly ferromagnetic LCMO layers.
△ Less
Submitted 24 September, 2019;
originally announced September 2019.
-
Coherent Epitaxial Semiconductor-Ferromagnetic Insulator InAs/EuS Interfaces: Band Alignment and Magnetic Structure
Authors:
Yu Liu,
Alessandra Luchini,
Sara Martí-Sánchez,
Christian Koch,
Sergej Schuwalow,
Sabbir A. Khan,
Tomaš Stankevič,
Sonia Francoua,
Jose R. L. Mardegan,
Jonas A. Krieger,
Vladimir N. Strocov,
Jochen Stahn,
Carlos A. F. Vaz,
Mahesh Ramakrishnan,
Urs Staub,
Kim Lefmann,
Gabriel Aeppli,
Jordi Arbiol,
Peter Krogstrup
Abstract:
Hybrid semiconductor-ferromagnetic insulator heterostructures are interesting due to their tunable electronic transport, self-sustained stray field and local proximitized magnetic exchange. In this work, we present lattice matched hybrid epitaxy of semiconductor - ferromagnetic insulator InAs/EuS heterostructures and analyze the atomic-scale structure as well as their electronic and magnetic chara…
▽ More
Hybrid semiconductor-ferromagnetic insulator heterostructures are interesting due to their tunable electronic transport, self-sustained stray field and local proximitized magnetic exchange. In this work, we present lattice matched hybrid epitaxy of semiconductor - ferromagnetic insulator InAs/EuS heterostructures and analyze the atomic-scale structure as well as their electronic and magnetic characteristics. The Fermi level at the InAs/EuS interface is found to be close to the InAs conduction band and in the bandgap of EuS, thus preserving the semiconducting properties. Both neutron and X-ray reflectivity measurements show that the ferromagnetic component is mainly localized in the EuS thin film with a suppression of the Eu moment in the EuS layer nearest the InAs. Induced moments in the adjacent InAs layers were not detected although our ab initio calculations indicate a small exchange field in the InAs layer. This work presents a step towards realizing high quality semiconductor - ferromagnetic insulator hybrids, which is a critical requirement for development of various quantum and spintronic applications without external magnetic fields.
△ Less
Submitted 19 August, 2019;
originally announced August 2019.
-
Indications for Dzyaloshinskii-Moriya Interaction at the Pd/Fe Interface Studied by \textit{In Situ} Polarized Neutron Reflectometry
Authors:
Sina Mayr,
Jingfan Ye,
Jochen Stahn,
Birgit Knoblich,
Oliver Klein,
Dustin A. Gilbert,
Manfred Albrecht,
Amitesh Paul,
Peter Böni,
Wolfgang Kreuzpaintner
Abstract:
Using \textit{in situ} polarized neutron reflectometry, the depth resolved evolution of the magnetism and structure in a Pd/Fe/Pd trilayer thin-film is measured during growth. The initial film structure of Pd/Fe shows a small proximity induced magnetism in the underlayer and a magnetization in the Fe layer of $\approx1.6$\,$μ_{\text{B}}$ per Fe atom, less than the expected bulk value of $2.2$\,…
▽ More
Using \textit{in situ} polarized neutron reflectometry, the depth resolved evolution of the magnetism and structure in a Pd/Fe/Pd trilayer thin-film is measured during growth. The initial film structure of Pd/Fe shows a small proximity induced magnetism in the underlayer and a magnetization in the Fe layer of $\approx1.6$\,$μ_{\text{B}}$ per Fe atom, less than the expected bulk value of $2.2$\,$μ_{\text{B}}$. Deposition of the Pd capping layer initially follows an island-like growth mode with subsequent coalescence. With increasing Pd deposition the Fe moment and the proximity-induced magnetism in the Pd capping layer decrease. After final deposition of the Pd capping layer, the magnetic profile is structurally and magnetically symmetric across the Fe layer, with magnetism induced in Pd up to 0.92 \,nm from the interface. Throughout the Pd deposition the Pd/Fe/Pd trilayer structure is becoming increasingly symmetric, a fact which points to a Dzyaloshinskii-Moriya interaction as a likely cause of the observed magnetic behavior.
△ Less
Submitted 27 June, 2019;
originally announced June 2019.
-
Influence of interface and microstructure on magnetization of epitaxial Fe4N thin film
Authors:
Nidhi Pandey,
S. Putter,
S. M. Amir,
V. R. Reddy,
D. M. Phase,
J. Stahn,
Ajay Gupta,
Mukul Gupta
Abstract:
Epitaxial Fe4N thin films grown on lattice-matched LaAlO3 (LAO) substrate using sputtering and molecular beam epitaxy techniques have been studied in this work. Within the sputtering process, films were grown with conventional direct current magnetron sputtering (dcMS) and for the first time, using a high power impulse magnetron sputtering (HiPIMS) process. Surface morphology and depth profile rev…
▽ More
Epitaxial Fe4N thin films grown on lattice-matched LaAlO3 (LAO) substrate using sputtering and molecular beam epitaxy techniques have been studied in this work. Within the sputtering process, films were grown with conventional direct current magnetron sputtering (dcMS) and for the first time, using a high power impulse magnetron sputtering (HiPIMS) process. Surface morphology and depth profile reveal that HiPIMS deposited film has the lowest roughness, the highest packing density and the sharpest interface. La from the LAO substrate and Fe from the film interdiffuse and forms an undesired interface spreading to an extent of about 10-20 nm. In the HiPIMS process, layer by layer type growth leads to a globular microstructure which restricts the extent of the interdiffused interface. Such substrate-film interactions and microstructure play a vital role in affecting the electronic hybridization and magnetic properties of Fe4N films. The magnetic moment (Ms) was compared using bulk, element-specific and magnetic depth profiling techniques. We found that Ms was the highest when the thickness of the interdiffused layer was lowest and only be achieved in the HiPIMS grown samples. Presence of small moment at the N site was also evidenced by element-specific x-ray circular dichroism measurement in HiPIMS grown sample. A large variation in the Ms values of Fe4N found in the experimental works carried out so far could be due to such interdiffused layer which is generally not expected to form in otherwise stable oxide substrate. In addition, a consequence of substrate-film interdiffusion and microstructure results in different kinds of different kind of magnetic anisotropies in films grown using different techniques.
△ Less
Submitted 4 June, 2019;
originally announced June 2019.
-
Finding pathways for stoichiometric Co4N thin films
Authors:
Nidhi Pandey,
Mukul Gupta,
Rachana Gupta,
Zaineb Hussain,
V. R. Reddy,
D. M. Phase,
Jochen Stahn
Abstract:
In this work, we studied the pathways for formation of stoichiometric \tcn~thin films. Polycrystalline and epitaxial \tcn~films were prepared using reactive direct current magnetron (dcMS) sputtering technique. A systematic variation in the substrate temperature (\Ts) during the dcMS process reveals that the lattice parameter (LP) decreases as \Ts~increases. We found that nearly stoichiometric \tc…
▽ More
In this work, we studied the pathways for formation of stoichiometric \tcn~thin films. Polycrystalline and epitaxial \tcn~films were prepared using reactive direct current magnetron (dcMS) sputtering technique. A systematic variation in the substrate temperature (\Ts) during the dcMS process reveals that the lattice parameter (LP) decreases as \Ts~increases. We found that nearly stoichiometric \tcn~films can be obtained when \Ts~= 300\,K. However, they emerge from the transient state of Co target ($φ$3\,inch). By reducing the target size to $φ$1\,inch, now the \tcn~phase formation takes place from the metallic state of Co target. In this case, LP of \tcn~film comes out to be $\sim$99\p~of the value expected for \tcn. This is the largest value of LP found so far for \tcn. The pathways achieved for formation of polycrystalline \tcn~were adopted to grow an epitaxial \tcn~film, which shows four fold magnetic anisotropy in magneto-optic Kerr effect measurements. Detailed characterization using secondary ion mass spectroscopy indicates that N diffuses out when \Ts~is raised even to 400\,K. Measurement of electronic structure using x-ray photoelectron spectroscopy and x-ray absorption spectroscopy further confirms it. Magnetization measurements using bulk magnetization and polarized neutron reflectivity show that the saturation magnetization of stoichiometric \tcn~film is even larger than pure Co. Since all our measurements indicated that N could be diffusing out, when \tcn~films are grown at high \Ts, we did actual N self-diffusion measurements in a CoN sample and found that N self-diffusion was indeed substantially higher. The outcome of this work clearly shows that the \tcn~films grown prior to this work were always N deficient and the pathways for formation of a stoichiometric \tcn~have been achieved.
△ Less
Submitted 14 January, 2019;
originally announced January 2019.
-
Density and Microstructure of Amorphous Carbon Thin Films
Authors:
Prabhat Kumar,
Mukul Gupta,
U. P. Deshpande,
D. M. Phase,
V. Ganesan,
Jochen Stahn
Abstract:
In this work, we studied amorphous carbon ($a$-C) thin films deposited using direct current (dc) and high power impulse magnetron sputtering (HiPIMS) techniques. The microstructure and electronic properties reveal subtle differences in $a$-C thin films deposited by two techniques. While, films deposited with dcMS have a smooth texture typically found in $a$-C thin films, those deposited with HiPIM…
▽ More
In this work, we studied amorphous carbon ($a$-C) thin films deposited using direct current (dc) and high power impulse magnetron sputtering (HiPIMS) techniques. The microstructure and electronic properties reveal subtle differences in $a$-C thin films deposited by two techniques. While, films deposited with dcMS have a smooth texture typically found in $a$-C thin films, those deposited with HiPIMS consist of dense hillocks surrounded by a porous microstructure. The density of $a$-C thin films is a decisive parameter to judge their quality. Often, x-ray reflectivity (XRR) has been used to measure the density of carbon thin films. From the present work, we find that determination of density of carbon thin films, specially those with a thickness of few tens of nm, may not be accurate with XRR due to a poor scattering contrast between the film and substrate. By utilizing neutron reflectivity (NR) in the time of flight mode, a technique not commonly used for carbon thin films, we could accurately measure differences in the densities of $a$-C thin films deposited using dcMS and HiPIMS.
△ Less
Submitted 5 January, 2018;
originally announced January 2018.
-
In-situ Polarized Neutron Reflectometry: Epitaxial Thin Film Growth of Fe on Cu(001) by DC Magnetron Sputtering
Authors:
Wolfgang Kreuzpaintner,
Birgit Wiedemann,
Jochen Stahn,
Jean-Francois Moulin,
Sina Mayr,
Thomas Mairoser,
Andreas Schmehl,
Alexander Herrnberger,
Panagiotis Korelis,
Martin Haese,
Jingfan Ye,
Matthias Pomm,
Peter Böni,
Jochen Mannhart
Abstract:
The step-wise growth of epitaxial Fe on Cu(001)/Si(001), investigated by in-situ polarized neutron reflectometry is presented. A sputter deposition system was integrated into the neutron reflectometer AMOR at the Swiss neutron spallation source SINQ, which enables the analysis of the microstructure and magnetic moments during all deposition steps of the Fe layer. We report on the progressive evolu…
▽ More
The step-wise growth of epitaxial Fe on Cu(001)/Si(001), investigated by in-situ polarized neutron reflectometry is presented. A sputter deposition system was integrated into the neutron reflectometer AMOR at the Swiss neutron spallation source SINQ, which enables the analysis of the microstructure and magnetic moments during all deposition steps of the Fe layer. We report on the progressive evolution of the accessible parameters describing the microstructure and the magnetic properties of the Fe film, which reproduce known features and extend our knowledge on the behavior of ultrathin iron films.
△ Less
Submitted 3 March, 2017;
originally announced March 2017.
-
Structure and Magnetization of Co4N Thin Film
Authors:
Nidhi Pandey,
Mukul Gupta,
Rachana Gupta,
Parasmani Rajput,
Jochen Stahn
Abstract:
In this work, we studied the local structure and the magnetization of Co4N thin films deposited by a reactive dc magnetron sputtering process. The interstitial incorporation of N atoms in a fcc Co lattice is expected to expand the structure and such expansion yields interesting magnetic properties characterized by a larger than Co magnetic moment and a very high value of spin polarization ratio in…
▽ More
In this work, we studied the local structure and the magnetization of Co4N thin films deposited by a reactive dc magnetron sputtering process. The interstitial incorporation of N atoms in a fcc Co lattice is expected to expand the structure and such expansion yields interesting magnetic properties characterized by a larger than Co magnetic moment and a very high value of spin polarization ratio in Co4N. By optimizing the growth conditions, we prepared Co4N film having lattice parameter close to its theoretically predicted value. The N concentration was measured using secondary ion mass spectroscopy. Detailed magnetization measurements using bulk magnetization method and polarized neutron reflectivity confirm that the magnetic moment of Co in Co4N is higher than that of Co.
△ Less
Submitted 11 February, 2017;
originally announced February 2017.
-
Effect of Al doping on phase formation and thermal stability of iron nitride thin films
Authors:
Akhil Tayal,
Mukul Gupta,
Nidhi Pandey,
Ajay Gupta,
M. Horisberger,
Jochen Stahn
Abstract:
In the present work, we systematically studied the effect of Al doping on the phase formation of iron nitride (Fe-N) thin films. Fe-N thin films with different concentration of Al (Al=0, 2, 3, 6, and 12 at.%) were deposited using dc magnetron sputtering by varying the nitrogen partial pressure between 0 to 100%. The structural and magnetic properties of the films were studied using X-ray diffracti…
▽ More
In the present work, we systematically studied the effect of Al doping on the phase formation of iron nitride (Fe-N) thin films. Fe-N thin films with different concentration of Al (Al=0, 2, 3, 6, and 12 at.%) were deposited using dc magnetron sputtering by varying the nitrogen partial pressure between 0 to 100%. The structural and magnetic properties of the films were studied using X-ray diffraction and polarized neutron reflectivity. It was observed that at the lowest doping level (2 at.% of Al), nitrogen rich non-magnetic Fe-N phase gets formed at a lower nitrogen partial pressure as compared to the un-doped sample. Interestingly, we observed that as Al doping is increased beyond 3at.%, nitrogen rich non-magnetic Fe-N phase appears at higher nitrogen partial pressure as compared to un-doped sample. The thermal stability of films were also investigated. Un-doped Fe-N films deposited at 10% nitrogen partial pressure possess poor thermal stability. Doping of Al at 2at.% improves it marginally, whereas, for 3, 6 and 12at.% Al doping, it shows significant improvement. The obtained results have been explained in terms of thermodynamics of Fe-N and Al-N.
△ Less
Submitted 20 May, 2015;
originally announced May 2015.
-
The origin of anomalous diffusion in iron mononitride thin films
Authors:
Akhil Tayal,
Mukul Gupta,
Ajay Gupta,
P. R. Rajput,
J. Stahn
Abstract:
We have studied the origin of a counter intuitive diffusion behavior of Fe and N atoms in a iron mononitride (FeN) thin film. It was observed that in-spite of a larger atomic size, Fe tend to diffuse more rapidly than smaller N atoms. This only happens in the N-rich region of Fe-N phase diagram, in the N-poor regions, N diffusion coefficient is orders of magnitude larger than Fe. Detailed self-dif…
▽ More
We have studied the origin of a counter intuitive diffusion behavior of Fe and N atoms in a iron mononitride (FeN) thin film. It was observed that in-spite of a larger atomic size, Fe tend to diffuse more rapidly than smaller N atoms. This only happens in the N-rich region of Fe-N phase diagram, in the N-poor regions, N diffusion coefficient is orders of magnitude larger than Fe. Detailed self-diffusion measurements performed in FeN thin films reveal that the diffusion mechanism of Fe and N is different - Fe atoms diffuse through a complex process, which in addition to a volume diffusion, pre-dominantly controlled by a fast grain boundary diffusion. On the other hand N atoms diffuse through a classical volume-type diffusion process. Observed results have been explained in terms of stronger Fe-N (than Fe-Fe) bonds generally predicted theoretically for mononitride compositions of transition metals.
△ Less
Submitted 23 April, 2015;
originally announced April 2015.
-
Effect of dopants on thermal stability and self-diffusion in iron nitride thin films
Authors:
Akhil Tayal,
Mukul Gupta,
Ajay Gupta,
M. Horisberger,
Jochen Stahn,
Kai Schlage,
H. -C. Wille
Abstract:
We studied the effect of dopants (Al, Ti, Zr) on the thermal stability of iron nitride thin films prepared using a dc magnetron sputtering technique. Structure and magnetic characterization of deposited samples reveal that the thermal stability together with soft magnetic properties of iron nitride thin films get significantly improved with doping. To understand the observed results, detailed Fe a…
▽ More
We studied the effect of dopants (Al, Ti, Zr) on the thermal stability of iron nitride thin films prepared using a dc magnetron sputtering technique. Structure and magnetic characterization of deposited samples reveal that the thermal stability together with soft magnetic properties of iron nitride thin films get significantly improved with doping. To understand the observed results, detailed Fe and N self-diffusion measurements were performed. It was observed that N self-diffusion gets suppressed with Al doping whereas Ti or Zr doping results in somewhat faster N diffusion. On the other hand Fe self-diffusion seems to get suppressed with any dopant of which heat of nitride formation is significantly smaller than that of iron nitride. Importantly, it was observed that N self-diffusion plays only a trivial role, as compared to Fe self-diffusion, in affecting the thermal stability of iron nitride thin films. Based on the obtained results effect of dopants on self-diffusion process is discussed.
△ Less
Submitted 13 June, 2014;
originally announced June 2014.
-
On the feasibility to study inverse proximity effect in a single S/F bilayer by Polarized Neutron Reflectometry
Authors:
Yu. N. Khaydukov,
B. Nagy,
J. -H. Kim,
T. Keller,
A. Rühm,
Yu. V. Nikitenko,
K. N. Zhernenkov,
J. Stahn,
L. Kiss,
A. Csik,
L. Bottyán,
V. L. Aksenov
Abstract:
Here we report on a feasibility study aiming to explore the potential of Polarized Neutron Reflectometry (PNR) for detecting the inverse proximity effect in a single superconducting/ferromagnetic bilayer. Experiments, conducted on the V(40nm)/Fe(1nm) S/F bilayer, have shown that experimental spin asymmetry measured at T = 0.5TC is shifted towards higher Q values compared to the curve measured at T…
▽ More
Here we report on a feasibility study aiming to explore the potential of Polarized Neutron Reflectometry (PNR) for detecting the inverse proximity effect in a single superconducting/ferromagnetic bilayer. Experiments, conducted on the V(40nm)/Fe(1nm) S/F bilayer, have shown that experimental spin asymmetry measured at T = 0.5TC is shifted towards higher Q values compared to the curve measured at T = 1.5TC. Such a shift can be described by the appearance in superconducting vanadium of magnetic sub-layer with thickness of 7 nm and magnetization of +0.8 kG.
△ Less
Submitted 11 June, 2013; v1 submitted 10 June, 2013;
originally announced June 2013.
-
Strain-induced ferromagnetism in antiferromagnetic LuMnO3 thin films
Authors:
J. S. White,
M. Bator,
Y. Hu,
H. Luetkens,
J. Stahn,
S. Capelli,
S. Das,
M. Döbeli,
Th. Lippert,
V. K. Malik,
J. Martynczuk,
A. Wokaun,
M. Kenzelmann,
Ch. Niedermayer,
C. W. Schneider
Abstract:
Single phase and strained LuMnO3 thin films are discovered to display co-existing ferromagnetic and antiferromagnetic orders. A large moment ferromagnetism (approx. 1 muB), which is absent in bulk samples, is shown to display a magnetic moment distribution that is peaked at the highly-strained substrate-film interface. We further show that the strain-induced ferromagnetism and the antiferromagneti…
▽ More
Single phase and strained LuMnO3 thin films are discovered to display co-existing ferromagnetic and antiferromagnetic orders. A large moment ferromagnetism (approx. 1 muB), which is absent in bulk samples, is shown to display a magnetic moment distribution that is peaked at the highly-strained substrate-film interface. We further show that the strain-induced ferromagnetism and the antiferromagnetic order are coupled via an exchange field, therefore demonstrating strained rare-earth managanite thin films as promising candidate systems for new multifunctional devices.
△ Less
Submitted 26 April, 2013;
originally announced April 2013.
-
Depth profile of the ferromagnetic order in a YBa$_2$Cu$_3$O$_7$ / La$_{2/3}$Ca$_{1/3}$MnO$_3$ superlattice on a LSAT substrate: a polarized neutron reflectometry study
Authors:
M. A. Uribe-Laverde,
D. K. Satapathy,
I. Marozau,
V. K. Malik,
S. Das,
K. Sen,
J. Stahn,
A. Rühm,
J. -H. Kim,
T. Keller,
A. Devishvili,
B. P. Toperverg,
C. Bernhard
Abstract:
Using polarized neutron reflectometry (PNR) we have investigated a YBa2Cu3O7(10nm)/La2/3Ca1/3MnO3(9nm)]10 (YBCO/LCMO) superlattice grown by pulsed laser deposition on a La0.3Sr0.7Al0.65Ta0.35O3 (LSAT) substrate. Due to the high structural quality of the superlattice and the substrate, the specular reflectivity signal extends with a high signal-to-background ratio beyond the fourth order superlatti…
▽ More
Using polarized neutron reflectometry (PNR) we have investigated a YBa2Cu3O7(10nm)/La2/3Ca1/3MnO3(9nm)]10 (YBCO/LCMO) superlattice grown by pulsed laser deposition on a La0.3Sr0.7Al0.65Ta0.35O3 (LSAT) substrate. Due to the high structural quality of the superlattice and the substrate, the specular reflectivity signal extends with a high signal-to-background ratio beyond the fourth order superlattice Bragg peak. This allows us to obtain more detailed and reliable information about the magnetic depth profile than in previous PNR studies on similar superlattices that were partially impeded by problems related to the low temperature structural transitions of the SrTiO3 substrates. In agreement with the previous reports, our PNR data reveal a strong magnetic proximity effect showing that the depth profile of the magnetic potential differs significantly from the one of the nuclear potential that is given by the YBCO and LCMO layer thickness. We present fits of the PNR data using different simple block-like models for which either a ferromagnetic moment is induced on the YBCO side of the interfaces or the ferromagnetic order is suppressed on the LCMO side. We show that a good agreement with the PNR data and with the average magnetization as obtained from dc magnetization data can only be obtained with the latter model where a so-called depleted layer with a strongly suppressed ferromagnetic moment develops on the LCMO side of the interfaces. The models with an induced ferromagnetic moment on the YBCO side fail to reproduce the details of the higher order superlattice Bragg peaks and yield a wrong magnitude of the average magnetization. We also show that the PNR data are still consistent with the small, ferromagnetic Cu moment of 0.25muB that was previously identified with x-ray magnetic circular dichroism and x-ray resonant magnetic reflectometry measurements on the same superlattice.
△ Less
Submitted 5 December, 2012;
originally announced December 2012.
-
Surfactant enhanced antiferromagnetic coupling in magnetron sputtered Cu/Co multilayers: A neutron reflectivity study
Authors:
S. M. Amir,
Mukul Gupta,
Ajay Gupta,
J. Stahn
Abstract:
In this work we studied Cu/Co multilayers prepared using dc-magnetron sputtering technique with Ag surfactant. It was found that Ag balances the difference in the surface free energy of Cu and Co and this results in removing the asymmetry in the interface roughness of Cu-on-Co and Co-on-Cu interfaces. As the interfaces become symmetric, we observe a significant enhancement in antiferromagnetic cou…
▽ More
In this work we studied Cu/Co multilayers prepared using dc-magnetron sputtering technique with Ag surfactant. It was found that Ag balances the difference in the surface free energy of Cu and Co and this results in removing the asymmetry in the interface roughness of Cu-on-Co and Co-on-Cu interfaces. As the interfaces become symmetric, we observe a significant enhancement in antiferromagnetic coupling and magneto resistance. Further, a correlation of spin-dependent scattering with the interface roughness is brought by comparing Cu/Co multilayer prepared using different deposition methods. It was found that as interface roughness increases spin-dependent scattering decreases.
△ Less
Submitted 24 September, 2012;
originally announced September 2012.
-
Magnetic proximity effect in $\mathbf{YBa_2Cu_3O_7/La_{2/3}Ca_{1/3}MnO_3}$ and $\mathbf{YBa_2Cu_3O_7/LaMnO_{3+δ}}$ superlattices
Authors:
D. K. Satapathy,
M. A. Uribe-Laverde,
I. Marozau,
V. K. Malik,
S. Das,
Th. Wagner,
C. Marcelot,
J. Stahn,
S. Brück,
A. Rühm,
S. Macke,
T. Tietze,
E. Goering,
A. Frañó,
J. -H. Kim,
M. Wu,
E. Benckiser,
B. Keimer,
A. Devishvili,
B. P. Toperverg,
M. Merz,
P. Nagel,
S. Schuppler,
C. Bernhard
Abstract:
Using neutron reflectometry and resonant x-ray techniques we studied the magnetic proximity effect (MPE) in superlattices composed of superconducting YBa$_2$Cu$_3$O$_7$ (YBCO) and ferromagnetic-metallic (FM-M) La$_{0.67}$Ca$_{0.33}$MnO$_{3}$ (LCMO) or ferromagnetic-insulating (FM-I) LaMnO$_{3+δ}$ (LMO). We find that the MPE strongly depends on the electronic state of the manganite layers, being pr…
▽ More
Using neutron reflectometry and resonant x-ray techniques we studied the magnetic proximity effect (MPE) in superlattices composed of superconducting YBa$_2$Cu$_3$O$_7$ (YBCO) and ferromagnetic-metallic (FM-M) La$_{0.67}$Ca$_{0.33}$MnO$_{3}$ (LCMO) or ferromagnetic-insulating (FM-I) LaMnO$_{3+δ}$ (LMO). We find that the MPE strongly depends on the electronic state of the manganite layers, being pronounced for the FM-M LCMO and almost absent for FM-I LMO. We also detail the change of the magnetic depth profile due to the MPE and provide evidence for its intrinsic nature.
△ Less
Submitted 7 June, 2012; v1 submitted 24 November, 2011;
originally announced November 2011.
-
Pulsed laser deposition growth of heteroepitaxial YBa2Cu3O7/La0.67Ca0.33MnO3 superlattices on NdGaO3 and Sr0.7La0.3Al0.65Ta0.35O3 substrates
Authors:
V. K. Malik,
I. Marozau,
S. Das,
B. Doggett,
D. K. Satapathy,
M. A. Uribe-Laverde,
N. Biskup,
M. Varela,
C. W. Schneider,
C. Marcelot,
J. Stahn,
C. Bernhard
Abstract:
Heteroepitaxial superlattices of [YBa2Cu3O7(n)/ La0.67Ca0.33MnO3(m)]x, where n and m are the number of YBCO and LCMO monolayers and x the number of bilayer repetitions, have been grown with pulsed laser deposition on NdGaO3 (110) and Sr0.7La0.3Al0.65Ta0.35O3 (LSAT) (001). These substrates are well lattice matched with YBCO and LCMO and, unlike the commonly used SrTiO3, they do not give rise to com…
▽ More
Heteroepitaxial superlattices of [YBa2Cu3O7(n)/ La0.67Ca0.33MnO3(m)]x, where n and m are the number of YBCO and LCMO monolayers and x the number of bilayer repetitions, have been grown with pulsed laser deposition on NdGaO3 (110) and Sr0.7La0.3Al0.65Ta0.35O3 (LSAT) (001). These substrates are well lattice matched with YBCO and LCMO and, unlike the commonly used SrTiO3, they do not give rise to complex and uncontrolled strain effects due to structural transitions at low temperature. The growth dynamics and the structure have been studied in-situ with reflection high energy electron diffraction (RHEED) and ex-situ with scanning transmission electron microscopy (STEM), x-ray diffraction, and neutron reflectometry. The individual layers are found to be flat and continuous over long lateral distances with sharp and coherent interfaces and with a well-defined thickness of the individual layer. The only visible defects are antiphase boundaries in the YBCO layers that originate from perovskite unit cell height steps at the interfaces with the LCMO layers. We also find that the first YBCO monolayer at the interface with LCMO has an unusual growth dynamics and is lacking the CuO chain layer while the subsequent YBCO layers have the regular Y-123 structure. Accordingly, the CuO2 bilayers at both the LCMO/YBCO and the YBCO/LCMO interfaces are lacking one of their neighboring CuO chain layers and thus half of their hole doping reservoir. Nevertheless, from electric transport measurements on asuperlattice with n=2 we obtain evidence that the interfacial CuO2 bilayers remain conducting and even exhibit the onset of a superconducting transition at very low temperature. Finally, we show from dc magnetization and neutron reflectometry measurements that the LCMO layers are strongly ferromagnetic.
△ Less
Submitted 18 October, 2011;
originally announced October 2011.
-
Formation of iron nitride thin films with Al and Ti additives
Authors:
Rachana Gupta,
Akhil Tayal,
Mukul Gupta,
Ajay Gupta,
M. Horisberger,
J. Stahn
Abstract:
In this work we investigate the process of iron nitride (Fe-N) phase formation using 2 at.% Al or 2 at.% Ti as additives. The samples were prepared with a magnetron sputtering technique using different amount of nitrogen during the deposition process. The nitrogen partial pressure (\pn) was varied between 0-50% (rest Argon) and the targets of pure Fe, [Fe+Ti] and [Fe+Al] were sputtered. The additi…
▽ More
In this work we investigate the process of iron nitride (Fe-N) phase formation using 2 at.% Al or 2 at.% Ti as additives. The samples were prepared with a magnetron sputtering technique using different amount of nitrogen during the deposition process. The nitrogen partial pressure (\pn) was varied between 0-50% (rest Argon) and the targets of pure Fe, [Fe+Ti] and [Fe+Al] were sputtered. The addition of small amount of Ti or Al results in improved soft-magnetic properties when sputtered using \pn $\leq$ 10\p. When \pn is increased to 50\p non-magnetic Fe-N phases are formed. We found that iron mononitride (FeN) phases (N at% $\sim$50) are formed with Al or Ti addition at \pn =50% whereas in absence of such addition \eFeN phases (N\pat$\sim$30) are formed. It was found that the overall nitrogen content can be increased significantly with Al or Ti additions. On the basis of obtained result we propose a mechanism describing formation of Fe-N phases Al and Ti additives.
△ Less
Submitted 13 September, 2011;
originally announced September 2011.
-
Surfactant induced smooth and symmetric interfaces in Cu/Co multilayers
Authors:
S. M. Amir,
Mukul Gupta,
Ajay Gupta,
J. Stahn,
A. Wildes
Abstract:
In this work we studied Ag surfactant induced growth of Cu/Co multilayers. The Cu/Co multilayers were deposited using Ag surfactant by ion beam sputtering technique. It was found that Ag surfactant balances the asymmetry between the surface free energy of Cu and Co. As a result, the Co-on-Cu and Cu-on-Co interfaces become sharp and symmetric and thereby improve the thermal stability of the multila…
▽ More
In this work we studied Ag surfactant induced growth of Cu/Co multilayers. The Cu/Co multilayers were deposited using Ag surfactant by ion beam sputtering technique. It was found that Ag surfactant balances the asymmetry between the surface free energy of Cu and Co. As a result, the Co-on-Cu and Cu-on-Co interfaces become sharp and symmetric and thereby improve the thermal stability of the multilayer. On the basis of obtained results, a mechanism leading to symmetric and stable interfaces in Cu/Co multilayers is discussed.
△ Less
Submitted 7 February, 2011;
originally announced February 2011.
-
Surfactant mediated growth of Ti/Ni multilayers
Authors:
Mukul Gupta,
S. M. Amir,
Ajay Gupta,
Jochen Stahn
Abstract:
The surfactant mediated growth of Ti/Ni multilayers is studied. They were prepared using ion beam sputtering at different adatom energies. It was found that the interface roughness decreased significantly when the multilayers were sputtered with Ag as surfactant at an ion energy of 0.75 keV. On the other hand, when the ion energy was increased to 1 keV, it resulted in enhanced intermixing at the i…
▽ More
The surfactant mediated growth of Ti/Ni multilayers is studied. They were prepared using ion beam sputtering at different adatom energies. It was found that the interface roughness decreased significantly when the multilayers were sputtered with Ag as surfactant at an ion energy of 0.75 keV. On the other hand, when the ion energy was increased to 1 keV, it resulted in enhanced intermixing at the interfaces and no appreciable effect of Ag surfactant could be observed. On the basis of the obtained results, the influence of adatom energy on the surfactant mediated growth mechanism is discussed.
△ Less
Submitted 3 February, 2011;
originally announced February 2011.
-
Relaxor characteristics at the interfaces of [NdMnO3/SrMnO3/LaMnO3] superlattices
Authors:
J. W. Seo,
B. T. Phan,
J. Stahn,
J. Lee,
C. Panagopoulos
Abstract:
We have investigated the magnetic properties of transition metal oxide superlattices with broken inversion symmetry composed of three different antiferromagnetic insulators, [NdMnO3/SrMnO3/LaMnO3]. In the superlattices studied here, we identify the emergence of a relaxor, glassy-like behavior below spin glass temperature, T=36K. Our results offer the possibility to study and utilize magnetically m…
▽ More
We have investigated the magnetic properties of transition metal oxide superlattices with broken inversion symmetry composed of three different antiferromagnetic insulators, [NdMnO3/SrMnO3/LaMnO3]. In the superlattices studied here, we identify the emergence of a relaxor, glassy-like behavior below spin glass temperature, T=36K. Our results offer the possibility to study and utilize magnetically metastable devices confined in nano-scale interfaces.
△ Less
Submitted 25 October, 2010; v1 submitted 3 June, 2010;
originally announced June 2010.
-
Fe and N self-diffusion in non-magnetic Fe:N
Authors:
M. Gupta,
A. Gupta,
R. Gupta,
J. Stahn,
M. Horisberger,
A. Wildes
Abstract:
Fe and N self-diffusion in non-magnetic FeN has been studied using neutron reflectivity. The isotope labelled multilayers, FeN/57Fe:N and Fe:N/Fe:15N were prepared using magnetron sputtering. It was remarkable to observe that N diffusion was slower compared to Fe while the atomic size of Fe is larger compared to N. An attempt has been made to understand the diffusion of Fe and N in non-magnetic Fe…
▽ More
Fe and N self-diffusion in non-magnetic FeN has been studied using neutron reflectivity. The isotope labelled multilayers, FeN/57Fe:N and Fe:N/Fe:15N were prepared using magnetron sputtering. It was remarkable to observe that N diffusion was slower compared to Fe while the atomic size of Fe is larger compared to N. An attempt has been made to understand the diffusion of Fe and N in non-magnetic Fe:N.
△ Less
Submitted 10 March, 2010;
originally announced March 2010.
-
Suppression of the structural phase transition and lattice softening in slightly underdoped Ba(1-x)K(x)Fe2As2 with electronic phase separation
Authors:
D. S. Inosov,
A. Leineweber,
Xiaoping Yang,
J. T. Park,
N. B. Christensen,
R. Dinnebier,
G. L. Sun,
Ch. Niedermayer,
D. Haug,
P. W. Stephens,
J. Stahn,
C. T. Lin,
O. K. Andersen,
B. Keimer,
V. Hinkov
Abstract:
We present x-ray powder diffraction (XRPD) and neutron diffraction measurements on the slightly underdoped iron pnictide superconductor Ba(1-x)K(x)Fe2As2, Tc = 32K. Below the magnetic transition temperature Tm = 70K, both techniques show an additional broadening of the nuclear Bragg peaks, suggesting a weak structural phase transition. However, macroscopically the system does not break its tetra…
▽ More
We present x-ray powder diffraction (XRPD) and neutron diffraction measurements on the slightly underdoped iron pnictide superconductor Ba(1-x)K(x)Fe2As2, Tc = 32K. Below the magnetic transition temperature Tm = 70K, both techniques show an additional broadening of the nuclear Bragg peaks, suggesting a weak structural phase transition. However, macroscopically the system does not break its tetragonal symmetry down to 15 K. Instead, XRPD patterns at low temperature reveal an increase of the anisotropic microstrain proportionally in all directions. We associate this effect with the electronic phase separation, previously observed in the same material, and with the effect of lattice softening below the magnetic phase transition. We employ density functional theory to evaluate the distribution of atomic positions in the presence of dopant atoms both in the normal and magnetic states, and to quantify the lattice softening, showing that it can account for a major part of the observed increase of the microstrain.
△ Less
Submitted 26 March, 2009;
originally announced March 2009.
-
Direct Observation of Magnon Fractionalization in the Quantum Spin Ladder
Authors:
B. Thielemann,
Ch. Rüegg,
H. M. Rønnow,
A. M. Läuchli,
J. -S. Caux,
B. Normand,
D. Biner,
K. W. Krämer,
H. -U. Güdel,
J. Stahn,
K. Habicht,
K. Kiefer,
M. Boehm,
D. F. McMorrow,
J. Mesot
Abstract:
We measure by inelastic neutron scattering the spin excitation spectra as a function of applied magnetic field in the quantum spin-ladder material (C5H12N)2CuBr4. Discrete magnon modes at low fields in the quantum disordered phase and at high fields in the saturated phase contrast sharply with a spinon continuum at intermediate fields characteristic of the Luttinger-liquid phase. By tuning the m…
▽ More
We measure by inelastic neutron scattering the spin excitation spectra as a function of applied magnetic field in the quantum spin-ladder material (C5H12N)2CuBr4. Discrete magnon modes at low fields in the quantum disordered phase and at high fields in the saturated phase contrast sharply with a spinon continuum at intermediate fields characteristic of the Luttinger-liquid phase. By tuning the magnetic field, we drive the fractionalization of magnons into spinons and, in this deconfined regime, observe both commensurate and incommensurate continua.
△ Less
Submitted 19 December, 2008;
originally announced December 2008.
-
Field-Controlled Magnetic Order in the Quantum Spin-Ladder System (Hpip)2CuBr4
Authors:
B. Thielemann,
Ch. Rüegg,
K. Kiefer,
H. M. Rønnow,
B. Normand,
P. Bouillot,
C. Kollath,
E. Orignac,
R. Citro,
T. Giamarchi,
A. M. Läuchli,
D. Biner,
K. Krämer,
F. Wolff-Fabris,
V. Zapf,
M. Jaime,
J. Stahn,
N. B. Christensen,
B. Grenier,
D. F. McMorrow,
J. Mesot
Abstract:
Neutron diffraction is used to investigate the field-induced, antiferromagnetically ordered state in the two-leg spin-ladder material (Hpip)2CuBr4. This "classical" phase, a consequence of weak interladder coupling, is nevertheless highly unconventional: its properties are influenced strongly by the spin Luttinger-liquid state of the ladder subunits. We determine directly the order parameter (tr…
▽ More
Neutron diffraction is used to investigate the field-induced, antiferromagnetically ordered state in the two-leg spin-ladder material (Hpip)2CuBr4. This "classical" phase, a consequence of weak interladder coupling, is nevertheless highly unconventional: its properties are influenced strongly by the spin Luttinger-liquid state of the ladder subunits. We determine directly the order parameter (transverse magnetization), the ordering temperature, the spin structure, and the critical exponents around the transition. We introduce a minimal, microscopic model for the interladder coupling and calculate the quantum fluctuation corrections to the mean-field interaction.
△ Less
Submitted 18 November, 2008; v1 submitted 2 September, 2008;
originally announced September 2008.
-
X-ray study of structural domains in the near-surface region of SrTiO3-substrates with Y0.6Pr0.4Ba2Cu3O7$ / La2/3Ca1/3MnO3 superlattices grown on top
Authors:
J. Hoppler,
J. Stahn,
H. Bouyanfif,
V. K. Malik,
B. D. Patterson,
P. R. Willmott,
G. Cristiani,
H. -U. Habermeier,
C. Bernhard
Abstract:
We investigated with synchrotron x-ray diffraction and reflectometry the formation of structural domains in the near-surface region of single crystalline SrTiO3 (001) substrates with Y0.6Pr0.4Ba2Cu3O7 / La2/3Ca1/3MnO3 superlattices grown on top. We find that the antiferrodistortive cubic-to-tetragonal transition, which occurs at T_STO = 104K in the bulk and at a considerably higher temperature o…
▽ More
We investigated with synchrotron x-ray diffraction and reflectometry the formation of structural domains in the near-surface region of single crystalline SrTiO3 (001) substrates with Y0.6Pr0.4Ba2Cu3O7 / La2/3Ca1/3MnO3 superlattices grown on top. We find that the antiferrodistortive cubic-to-tetragonal transition, which occurs at T_STO = 104K in the bulk and at a considerably higher temperature of at least 120K in the surface region of SrTiO3, has only a weak influence on the domain formation. The strongest changes occur instead in the vicinitiy of the tetragonal-to-orthorhombic transition in SrTiO3 around 65K, where pronounced surface facets develop that reach deep (at least several micrometers) into the SrTiO3 substrate. These micrometer-sized facets are anisotropic and tilted with respect to one another by up to 0.5deg along the shorter direction. Finally, we find that a third structural transition below 30K gives rise to significant changes in the spread of the c-axis parameters. Overall, our data provide evidence for a strong mutual interaction between the stuctural properties of the SrTiO3 surface and the multilayer grown on top.
△ Less
Submitted 28 August, 2008; v1 submitted 23 June, 2008;
originally announced June 2008.
-
Tuning competing orders in La2-xSrxCuO4 cuprate superconductors by the application of an external magnetic field
Authors:
J. Chang,
Ch. Niedermayer,
R. Gilardi,
N. B. Christensen,
H. M. Ronnow,
D. F. McMorrow,
M. Ay,
J. Stahn,
O. Sobolev,
A. Hiess,
S. Pailhes,
C. Baines,
N. Momono,
M. Oda,
M. Ido,
J. Mesot
Abstract:
We report the results of a combined muon spin rotation and neutron scattering study on La2-xSrxCuO4 in the vicinity of the so-called 1/8-anomaly. Application of a magnetic field drives the system towards a magnetically ordered spin-density-wave state, which is fully developed at 1/8 doping. The results are discussed in terms of competition between antiferromagnetic and superconducting order para…
▽ More
We report the results of a combined muon spin rotation and neutron scattering study on La2-xSrxCuO4 in the vicinity of the so-called 1/8-anomaly. Application of a magnetic field drives the system towards a magnetically ordered spin-density-wave state, which is fully developed at 1/8 doping. The results are discussed in terms of competition between antiferromagnetic and superconducting order parameters.
△ Less
Submitted 14 December, 2007; v1 submitted 13 December, 2007;
originally announced December 2007.
-
Multiple Magnon Modes and Consequences for the Bose-Einstein Condensed Phase in BaCuSi2O6
Authors:
Ch. Rüegg,
D. F. McMorrow,
B. Normand,
H. M. Ronnow,
S. E. Sebastian,
I. R. Fisher,
C. D. Batista,
S. Gvasaliya,
Ch. Niedermayer,
J. Stahn
Abstract:
The compound BaCuSi2O6 is a quantum magnet with antiferromagnetic dimers of S = 1/2 moments on a quasi-2D square lattice. We have investigated its spin dynamics by inelastic neutron scattering experiments on single crystals with an energy resolution considerably higher than in an earlier study. We observe multiple magnon modes, indicating clearly the presence of magnetically inequivalent dimer s…
▽ More
The compound BaCuSi2O6 is a quantum magnet with antiferromagnetic dimers of S = 1/2 moments on a quasi-2D square lattice. We have investigated its spin dynamics by inelastic neutron scattering experiments on single crystals with an energy resolution considerably higher than in an earlier study. We observe multiple magnon modes, indicating clearly the presence of magnetically inequivalent dimer sites. This more complex spin Hamiltonian leads to a distinct form of magnon Bose-Einstein condensate (BEC) phase with a spatially modulated condensate amplitude.
△ Less
Submitted 30 November, 2006; v1 submitted 18 July, 2006;
originally announced July 2006.
-
Magnetic Proximity Effect in Perovskite Superconductor/Ferromagnet Multilayers
Authors:
J. Stahn,
J. Chakhalian,
C. Niedermayer,
J. Hoppler,
T. Gutberlet,
J. Voigt,
F. Treubel,
H. -U. Habermeier,
G. Cristiani,
B. Keimer,
C. Bernhard
Abstract:
$\mathrm{YBa_2Cu_3O_7/La_{2/3}Ca_{1/3}MnO_3}$ superconducting/ferromagnetic (SC/FM) multilayers have been studied by neutron reflectometry. Evidence for a characteristic difference between the structural and magnetic depth profiles is obtained from the occurrence of a structurally forbidden Bragg peak in the FM state. The comparison with simulated reflectivity curves allows us to identify two po…
▽ More
$\mathrm{YBa_2Cu_3O_7/La_{2/3}Ca_{1/3}MnO_3}$ superconducting/ferromagnetic (SC/FM) multilayers have been studied by neutron reflectometry. Evidence for a characteristic difference between the structural and magnetic depth profiles is obtained from the occurrence of a structurally forbidden Bragg peak in the FM state. The comparison with simulated reflectivity curves allows us to identify two possible magnetization profiles: a sizable magnetic moment within the SC layer antiparallel to the one in the FM layer (inverse proximity effect), or a ``dead'' region in the FM layer with zero net magnetic moment. The former scenario is supported by an anomalous SC-induced enhancement of the off-specular reflection, which testifies to a strong mutual interaction of SC and FM order parameters.
△ Less
Submitted 13 August, 2004;
originally announced August 2004.
