Technical Report Home Automation By Group # 9 Team Members Tajmmal Waqas Aqil Javeed Rabbia Waheed Sadia Manzoor A TECHNICAL REPORT SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE DEGREE OF MASTER OF SCIENCE IN PHYSICS Department of Physics FACULTY OF SCIENCES UNVERSITY OF SAHIWAL Content ACKNOWLEDGEMENT………………………………………………………………………………………………………………… 1 ABSTRACT……………………………………………………………………………………………………………………………………. 2 INTRODUTION………………………………………………………………………………………………………………………………. 3 PROJECT AIM & SCOPE……………………………………………………………………………………………………………………4 DESCRIPTION OF PROJECT………………………………………………………………………………………………………………5 H/W & S/W REQUIREMENT……………………………………………………………………………………………………………..6 DESCRIPTION OF H/W REQUIRED…………………………………………………………………………………………………….7 INEREFACING OF HC-05 MODULE…………………………………………………………………………………………………….8 DESIGN & IMPLEMENTATION…………………………………………………………………………………………………………..9 PROS & CONS…………………………………………………………………………………………………………………………………..10 APPLICATION……………………………………………………………………………………………………………………………………11 FUTURE DEVELOPMENT…………………………………………………………………………………………………………………..12 CONCLUSION……………………………………………………………………………………………………………………………………13 Acknowledgement First and foremost, I would like to take this opportunity to thank our Head of department physics Mr. Hafiz TARIQ MASOOD for his guidance and advice on this project. At the same time I also won’t forget my group participant also friend to because they quite good with sharing some of their information to complete this project successfully. Last but not least, I am very grateful to our university, lecture sand friends where they gave us enough of time to complete this project and at the same time I would like to thank my friends and classmates who helps me a lot to complete this project. Thank You. 1 Abstract The main objective of this project is to develop a home automation system using an Arduino board with Bluetooth being remotely controlled by any Android OS smart phone. As technology is advancing so houses are also getting smarter. Modern houses are gradually shifting from conventional switches to centralized control system, involving remote controlled switches. Presently, conventional wall switches located in different parts of the house make it difficult for the user to go near them to operate. Even more it becomes more difficult for the elderly or physically handicapped people to so. Remote controlled home automation system provides a most modern solution with smart phones. In order to achieve this, a Bluetooth module is interfaced to the Arduino board at the receiver end while on the transmitted end, A GUI application on the cell phone sends ON/OFF commands to the receiver where loads are connected. By touching the specified location on the GUI, the loads can be turned ON/OFF remotely through this technology. 2 Introduction Nowadays, we have remote controls for our television sets and others electronic Systems, which have made our lives real easy. Have you ever wondered about home automation which Would give the facility of controlling tube lights, fan and other electrical appliances at home using a remote control? Off-course, yes but, are the available options cost-effective? If the answer is no, we have found a solution to it. We have come up with a new system is super-cost effective and can give the user, the ability to control any electronic device without even spending for a remote control. This project helps the user to control all the electronic devices using his/her smartphone. Time is very valuable thing. Everybody wants to save time as much as they can . New technologies are being introduced to save our time. To save people’s time we are introducing Home Automation system using Bluetooth. Whit your mobile phone. You can turn on/off your home appliances the range of Bluetooth. Project Aim The aim the project is to design and construct a home automation system that Will remotely switch on or Off any household appliances connected to it, using a microcontroller, voice dial on phone, or Bluetooth based android application . Project Objective The objective of this project is to implement a low cost, reliable and scalable Home automation system that can be used to remotely switch on or off any Household appliance, using a microcontroller to achieve hardware simplicity Low cost short messaging service for feedback voice dial from phone to toggle The switch state. Project scope and limitation This project work is complete on its own in remotely and automatically switching On or Off an electrical appliance not limited to household appliances and sends Feedback message indicating the new present state of the appliance. 4 Description of the project This project is one of the important Arduino Projects. Arduino based home Automation using Bluetooth project helps the user to control any electronic Device using Device control app on their Android Smartphone. The android app The android app sends commands to controller- Arduino smart phone. The android Sends commands to the controller-Arduino through wireless communication, Namely, Bluetooth. The Arduino is connected to the main PCB which has five Relays as shown in the block diagram, Device 1- buzzer, Device 2- Door, Device 3- lights. When the user presses on the On button displayed on the app for the device 1, The Buzzer is switched on. The buzzer can be switched off, by pressing the same Button again . Similarly, when the user presses on the ‘on’ button displayed on the app for the device 2 The door is open . the door can be close by pressing the same button again. This project of home automation using Bluetooth and Arduino can be used for controlling any AC or DC devices. In the demonstration, we have used DC fan and DC bulb. To drive this DC lights and Door , 9v battery is connected. 5 Hardware Requirement The list of components mentioned here are specifically for different loads.             Arduino Uno. Bluetooth module for connectivity. Push button. 9 volt battery. 1.5 volt led x4. Heat sink. 7806 voltage controller. Server motor Vero board Android or IOS phone or tablet . Connecting wire. 1 kΩ Resistance x4. Software requirement  Arduino complier  Android application  Proteus 7 6 Description of Hardware Required Arduino uno The arduino uno is a microcontroller board on the ATmega 328p. it has 14 Digital input/output pins (of which 6 can used as PWM outputs), 6 analogs Inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICPS Header, and a reset button. it contains everything needed to support the Microcontroller simply connect it to a computer with a USB cable or power it With a Ac to Dc adapter or battery to get started. The uno differs from all preceding boards in that it does not use the FTDI USB-toSerial driver chip. Instead. It features the Atmega 8U2 programmed as USB-toSerial converter.  some Technical specification of Arduino Uno are 1. Microcontroller ATmega328P 2. Operating voltage 5v 3. Input voltage( recommended) 7-12V 4. Input voltage( limits) 6-20V 5. Digital I/O pin 14 6. Analog input pins 6 7. Dc current per I/O pin 40mA 8. Dc current for 3.3V pin 50mA 9. Flash memory 32KB of which 0.5 KB used by boot loader 10. SRAM 2KB 11. EEPROM 1KB 12. Clock Speed 16 MHz 7 Circuit diagram 8 Bluetooth module HC-05 module is an easy to use Bluetooth SSP module designed for transparent wireless serial connection setup. Serial port Bluetooth module is fully qualified Bluetooth v2.0+EDR 3Mbps modulation with complete 2.4GHz radio transceiver and Base band. It uses CSR blue core 04External single Bluetooth system with CMOS technology and with AFH(adaptive frequency Hopping feature). It has the Footprint as small as 12.7 mmx 27 mm. Hope it will simplify your overall Design/development cycle. 9 Bluetooth Module Interfacing with Arduino UNO HC-05 is a Bluetooth device used for wireless communication with Bluetooth Enabled devices(like smartphone). It communicates with microcontrollers using Serial communication(USART). Default settings of HC-05 Bluetooth module can be changed using certain At Commands. As Hc-05 Bluetooth module has 3.3 level for Rx/Tx and microcontroller can Decet 3.3 v level, so there is no need to shift TX voltage of Hc-05 module. But we need to shift the transmit voltage level from microcontroller to RX of Hc-05 module. 10 Servo motor The servo motor is a closed-loop mechanism that incorporates positional feedback in order to control the rotational or linear speed and position. The motor is controlled with an electric signal, either analog or digital, which determines the amount of movement which represents the final command position for the shaft. Servos are used in radio-controlled airplanes to position control surfaces like elevators, rudders, walking a robot, or operating grippers. Servo motors are small, have built-in control circuitry and have good power for their size 11 Design And Implementation A low cost and efficient smart home system is presented in our desing. This system has two modules. The hardware interface and the software Communication module. At the heart of this system is the Arduino microcontroller Which is also capable of functioning as a micro web server and the system pass through The microcontroller. Designing the Circuit 12 Program Code 13 Pros of Home Automation 1. Security Tap your finger to turn on the lights when get home so you worried about What’s hiding in the shadows. Or in your pathways. Or automate to turn on when You are not home to look like you are to ward off potential robbers. Door lacks are another automated home product that increase your home security. 2. Energy Efficiency Increase your home energy efficiency by remotley powering off systems and appliances when they aren’t in use. In addition to the standard home automation Products that give you active control. Some products actively monitor systems and arm the homeowner with knowledge. Insight and guidance to achiere greater control and energy efficiency. 3. Saving Home automation literally pays off. When you are use home systems And appliances only when needed. The saving will apparent in the first Utilty bill. No more wasting money on lights left on when you are not home . 14 Application  Using this project ,we can turn on or off appliances remotely, using Phone or tablet.  The project can be further expanded to a smart home automation System by including some sensors like lights sensors, temperature sensor, Safety sensors etc. and automatically (room temperature), door etc, and Transmit the information to our phone.  Additionally, we can connect to internet and control the home from Remote location over internet and also montior the safety. 15 Conclusion The home automation system has been experimentally proven to work satisfied by connecting sample appliances to it and the application were successfully controlled from a wireless mobile device. We learned many skills such as soldering wiring the circuit and other tools that we use for this project and was able to work together as a team during this project. The Bluetooth client was successfully tested on a multitude of different mobile phones from different manufacturers, thus proving its portability and wide compatibly. Thus a low- cost home automation system was successfully designed. Implement and tested.