Chapter 1

Product Descriptions
1.1 Features....................................................................................................................1
1.2 Specifications ..........................................................................................................2
1.2.1 Printing Specification................................................................................................................ 2
1.2.2 Paper Specification ................................................................................................................... 5
1.2.2.1 Cut Sheet...................................................................................................................... 5
1.2.2.2 Transparency Film / Glossy Paper ............................................................................... 5
1.2.2.3 Envelope....................................................................................................................... 5
1.2.2.4 Index Card.................................................................................................................... 5
1.2.3 Adjust Lever Settings (PG adjust lever) .................................................................................. 6
1.2.4 Printable Area ............................................................................................................................ 7
1.2.4.1 Cut Sheet...................................................................................................................... 7
1.2.4.2 Envelope....................................................................................................................... 8
1.2.5 Environmental Condition.......................................................................................................... 9
1.2.6 Ink Cartridge Specifications ................................................................................................... 10
1.2.6.1 Black Ink Cartridge ..................................................................................................... 10
1.2.6.2 Color Ink Cartridge ..................................................................................................... 11
1.2.7 Physical Specification............................................................................................................. 12
1.2.8 Electric Specification .............................................................................................................. 13
1.2.9 Reliability.................................................................................................................................. 13
1.2.10 Safety Approvals ................................................................................................................... 13
1.2.11 Acoustic Noise....................................................................................................................... 13
1.2.12 CE Marking............................................................................................................................. 13
1.2.13 Printer Language and Emulation ......................................................................................... 14

1.3 Interface..................................................................................................................16
1.3.1 Parallel Interface (Forward Channel) ..................................................................................... 16
1.3.2 Parallel Interface (Reverse Channel) ..................................................................................... 17
1.3.2.1 Prevention Hosts from Data Transfer Time-out ......................................................... 19
1.3.3 Serial Interface ......................................................................................................................... 20

1.4 Control Panel .........................................................................................................21

1.4.1 Indicators.................................................................................................................................. 21
1.4.2 Panel Functions....................................................................................................................... 22
1.4.3 Printer Condition and Panel Status ....................................................................................... 23

1.5 Error Status............................................................................................................24

1.5.1 Ink Out ...................................................................................................................................... 24
1.5.2 Paper Out.................................................................................................................................. 24
1.5.3 Paper Jam................................................................................................................................. 24
1.5.4 No Ink-Cartridge Error............................................................................................................. 25
1.5.5 Maintenance Request.............................................................................................................. 25
1.5.6 Fatal Errors............................................................................................................................... 25

1.6 Printer Initialization ...............................................................................................26

1.6.1 Initialization Settings............................................................................................................... 26

1.7 Main Components ................................................................................................. 27

1.7.1 Printer Mechanism................................................................................................................... 27
1.7.2 C200 MAIN Board ..................................................................................................................... 28
1.7.3 C206 PSB/PSE Board............................................................................................................... 29
1.7.4 C206 PNL Board ....................................................................................................................... 29

Chapter 1 Product Description

1.1 Features
EPSON Stylus Color 600 is designed for low price for that high performance. The major printer features
are;

High color print quality

1440(H) x 720(V) dpi printing
Standard 4 color printing (CMY+Bk)
Traditional and New Microwave control to eliminate banding





Built-in auto sheet feeder

Holds 100 cut-sheets (64g/u)
Holds 10 envelopes
Holds 10 transparency films
Holds 65 special papers






High-speed print
200cps (at LQ/10CPI; No-Draft mode)
By driving the printhead at frequency; 14.4KHz, printing speed is twice faster than Stylus Color.




Compact size
Non-operating : 429mm(W) x 275mm(D) x 168mm(H)
Operating
: 429mm(W) x 613mm(D) x 309mm(H)
Weight
: 5.2Kg (without cartridge)





Acoustic noise
Approximately 47dB(A)

Two built-in standard I/F

Bi-directional Parallel I/F (IEEE-1284 level 1 device)
Serial I/F (Macintosh-compatible / up to 900Kbps)
The table below shows consumable for EPSON Stylus Color 600.




Table 1-1 Available Consumable

Item
Black Ink Cartridge
Color Ink Cartridge
EPSON 360 dpi Ink Jet Paper
EPSON 360 dpi Ink Jet Paper
EPSON 360 dpi Ink Jet Paper
Photo Quality Ink Jet Paper
Photo Quality Ink Jet Paper
Photo Quality Ink Jet Paper
Photo Quality Ink Jet Paper
Photo Quality Glossy Paper(New Release)
Photo Quality Glossy Paper(New Release)
Photo Quality Glossy Film
Photo Quality Glossy Film
Photo Quality Glossy Film
Ink Jet Transparencies
Ink Jet Transparencies
Photo Quality Ink Jet Card
Photo Quality Ink Jet Card
Photo Quality Ink Jet Card
Photo Quality Self Adhesive Sheet

Rev. A

Code
S020093
S020089
S041025
S041059
S041060
S041026
S041061
S041062
S041067
S041126
S041124
S041071
S041072
S041107
S041063
S041064
S041054
S041121
S041122
S041106

Remark
Color: Black
Color: Cyan/Magenta/Yellow
Size: A4(200 sheets)
Size: A4(100 sheets)
Size: Letter(100 sheets)
Size: A4(200 sheets)
Size: A4(100 sheets)
Size: Letter
Size: Legal
Size: A4
Size: Letter
Size: A4
Size: Letter
Size: A6
Size: A4
Size: Letter
Size: A6
Size: 5 x 8 inches
Size: 10 x 8 inches
Size: A4

1-1

EPSON Stylus Color 600

1.2 Specifications
This section describes the product specifications for EPSON Stylus Color 600.

1.2.1 Printing Specification

Print method
 On-demand color ink jet printing

Nozzle configuration
 Black: 64 nozzles (32 nozzles x2 staggered / Nozzle pitch = 180dpi/vertical)
Color:
32 nozzles (per color (CMY) / Nozzle pitch = 90dpi/vertical)

Print Direction
 Bi-directional printing with logical seeking for text and graphics

Print Buffer: 32KBytes

Print speed and Printable Columns
Table 1-2 Print Speed (Text Mode)
Character Pitch

Printable
Column
80
96
120
137
160

10 CPI (Pica)
12 CPI (Elite)
15 CPI
17 CPI (Pica Condensed)
20 CPI (Elite Condensed)

Draft Speed
(CPS)
400
480
600
684
800

LQ Speed
(CPS)
200
240
300
342
400

Table 1-3 Print Speed (Raster Graphics Mode)

Horizontal Resolution

Printable
Area
180 dpi
8.26 inch
360 dpi
8.26 inch
720 dpi
8.26 inch
Nozzle arrangement: See figure below.

Available Dot

CR Speed
(IPS)
20
20
20

1488
2976
5952

320/360" (22.5778mm)
144/360" (10.16mm)
32/360" (2.2578mm)

32/360" (2.2578mm)

#64
#63

#32

#32

#32

180dpi

90dpi

Paper feed
direction

#2

#3
#1

Black

#1

Cyan

#1

Magenta

#1

Yellow

*Viewed from the back of the head

Figure 1-1. Nozzle Layout

1-2

Rev. A



Chapter 1 Product Description

Paper Feeding Method
Friction feed with built in ASF (Auto Sheet Feeder)

Line Spacing
1/6 inch or programmable at 1/360 inch

Paper Path
Top entry (from ASF) only

Feeding Speed
66.6 ms (at 1/6 inch line-feed)
3.0 inch/sec (76.2 mm/sec / at continuous-feed)




ASF Capacity
Size
:Index card to Legal
Thickness *1
:Less than 8mm
Paper capacity *2 :Normal cut sheets
:Envelops
:Coated papers (360dpi)
:Coated papers (720dpi)
:Glossy papers *3 *4
:Transparency films *4
:Index cards *4





=100 sheets (64g/m )

=10
=65
=65
=30
=30
=30

Notes) *1: Total thickness of paper stack on the ASF.

*2: Those numbers above should be considered as reference. The actual paper accumulation
should be considered first.
*3: Only when the top margin is set for 30mm with A4/Letter size paper, otherwise only one sheet
can be set at a time.
*4: Specified paper must be set at the bottom of stack to ensure proper feeding operation:




Rev. A

Normal paper
=Glossy paper, Transparency film
Card Board
=Index card
(The one packed with the index card package)

1-3

EPSON Stylus Color 600

Control Code
ESC/P2 and expanded raster graphics code
EPSON Remote command




Character Tables
Legal and 14 international character sets
Standard version: 11 character tables (See Table 1-4 for details)
NLSP version:
19 character tables (See Table 1-4 for details)




Typeface *1
Bit map LQ font:

Scaleable font:

EPSON Roman
EPSON Sans Serif
EPSON Courier
EPSON Prestige
EPSON Script

(10/12/15 CPI, Proportional)

(10/12/15 CPI, Proportional)
(10/12/15 CPI)
(10/12/15 CPI)
(10/12/15 CPI)

EPSON Roman
EPSON Sans Serif
EPSON Roman T
EPSON Sans Serif H

(10.5 pt, 8 to 32 pt (every 2 pt))

(10.5 pt, 8 to 32 pt (every 2 pt))
(10.5 pt, 8 to 32 pt (every 2 pt))
(10.5 pt, 8 to 32 pt))

Note) *1: Each typeface has four different font style; Normal, Bold, Italic and Bold-Italic.
Table 1-4 Character Table and Typeface
Version
Common

Standard

NLSP

1-4

Character Table

Italic
PC437 (US / Standard Europe)
PC850 (Multilingual)
PC860 (Portuguese)
PC861 (Icelandic)
PC863 (Canadian-French)
PC865 (Nordic)
BRASCII
Abicomp
Roman 8
ISO Latin 1
Italic
PC437 (US / Standard Europe)
PC850 (Multilingual)
PC437 Greek
PC852 (East Europe)
PC853 (Turkish)
PC855 (Cyrillic)
PC857 (Turkish)
PC866 (Russian)
PC869 (Greek)
MAZOWIA (Poland)
Code MJK (CSFR)
ISO 8859-7 (Latin/Greek)
ISO Latin 1T (Turkish)
Bulgaria (Bulgaria)
PC774
Estonia
ISO 8859-2 (ISO Latin 2)
PC866 LAT

Bit-map Font
EPSON - ;
Roman
Sans Serif
Courier
Prestige
Script
Supported

Scaleable Font
EPSON - ;
EPSON - ;
Roman
Roman T
Sans Serif
Sans Serif H

Supported

Supported

Supported

Supported

Supported

Supported

Supported

Not
Supported

Rev. A

Chapter 1 Product Description

1.2.2 Paper Specification

This section describes the types of paper that can be used in this printer.

1.2.2.1 Cut Sheet

[Size]

:A4
[Width 210mm (8.3) x Length 297mm (11.7)]
:Letter
[Width 216mm (8.5) x Length 279mm (11.0)]
:B5
[Width 182mm (7.2) x Length 257mm (10.1)]
:Legal
[Width 216mm (8.5) x Length 356mm (14.0)]
:Half Letter [Width 139.7mm (5.5) x Length 215.9mm (8.5)]
:Exclusive [Width 190.5mm (7.5) x Length 254mm (10)]

[Thickness]
[Weight]
[Quality]

:0.08mm (0.003) - 0.11mm (0.004)

2
2
:64g/m (17Ib.) - 90g/m (24Ib.)
:Exclusive paper, Bond paper, PPC

1.2.2.2 Transparency Film / Glossy Paper

[Size]

:A4
:Letter
:A6

[Thickness]

:0.13mm (0.005) - 0.15mm (0.006)

:0.17mm (0.007) - 0.18mm (0.007) for glossy paper

[Width 210mm (8.3) x Length 297mm (11.7)]

[Width 216mm (8.5) x Length 279mm (11.0)]
[Width 105mm (4.1) x Length 148mm (5.8)]

Note) Transparency printing is only available at normal temperature.

1.2.2.3 Envelope
[Size]

: No.10
: DL
: C6

[Thickness]
[Weight]
[Quality]

: 0.16mm (0.006) - 0.43mm (0.017)

2
2
: 45g/m (12Ib.) - 75g/m (20Ib.)
: Bond paper, Plain paper, Air mail

[Width 241mm (9 1/2) x Length 104.8mm (4 1/8)]

[Width 220mm (8.7) x Length 110mm (4.3)]
[Width 162mm (6.4) x Length 114mm (4.5)]

Note) 1. Envelop printing is only available at normal temperature.

2. Keep the longer side of the envelope horizontally at setting.

1.2.2.4 Index Card

[Size]

:A6 Index card

[Width 105mm (4.1) x Length 148mm (5.8)]
:5x8 Index card [Width 127mm (5.0) x Length 203mm (8.0)]
:10x8 Index card [Width 127mm (5.0) x Length 203mm (8.0)]

[Thickness]
[Weight]

:Less than 0.23mm(0.0091)

2
:188g/m

Note) 1. No curled, wrinkled, scuffing or torn paper be used.

2. Set the lever to the proper position according to the paper type you print. (Refer to section
1.2.3 for details)
3. Printing should be performed at room temperature in spite of the paper types.

Rev. A

1-5

EPSON Stylus Color 600

1.2.3 Adjust Lever Settings (PG adjust lever)

The adjust lever located on the right side (blue knob) under the printer cover needs to be set to the proper
position according to the paper you print (Refer to the table below). Also, if there is any dirt caused by
friction on the wavy or wrinkled paper, this can be prevented by changing the lever position to rear position
(marked with +) in spite of paper types.
Table 1-5. Adjust Lever Settings
Paper
Normal paper,
Coated paper
Transparency film
Label
Envelopes

Lever position
Front

PG adjustment value
0 mm (1.1mm between head and platen)

Rear

0.9 mm (2.0mm between head and platen)

Front (Mark "0")

Rear (Mark "+")

Level adjustment lever

CR Guide Shaft
Bush

Figure 1-2. Adjust Lever Settings

1-6

Rev. A

Chapter 1 Product Description

1.2.4 Printable Area

1.2.4.1 Cut Sheet
Following tables show printable areas at Character mode and Raster Graphics mode.
Table 1-6. Character Table
Paper size

PW
(Paper width)
(typ.)

A4
Letter
B5
Legal
Statement
Executive

210mm(8.3)
216mm(8.5)
182mm(7.2)
216mm(8.5)
139.7mm(5.5)
190.5mm(7.5)

PL
LM
(Paper
(Left margin)
Length)
(min.)
(typ.)
297mm(11.7) 3mm(0.12)
279mm(11.0) 3mm(0.12)
257mm(10.1) 3mm(0.12)
356mm(14.0) 3mm(0.12)
215.9mm(8.5) 3mm(0.12)
254mm(10)
3mm(0.12)

RM
(Right
margin)
(min.)
3mm(0.12)
9mm(0.35)
3mm(0.12)
9mm(0.35)
3mm(0.12)
3mm(0.12)

TM
(Top margin)
(min.)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)

BM
(Bottom
margin)
(min.)
14mm(0.54)
14mm(0.54)
14mm(0.54)
14mm(0.54)
14mm(0.54)
14mm(0.54)

Table 1-7. Raster Graphics Mode

Paper size

PW
(Paper width)
(typ.)

A4
Letter
B5
Legal
Statement
Executive

210mm(8.3)
216mm(8.5)
182mm(7.2)
216mm(8.5)
139.7mm(5.5)
190.5mm(7.5)

PL
LM
(Paper
Left margin)
Length)
(min.)
(typ.)
297mm(11.7) 3mm(0.12)
279mm(11.0) 3mm(0.12)
257mm(10.1) 3mm(0.12)
356mm(14.0) 3mm(0.12)
215.9mm(8.5) 3mm(0.12)
254mm(10)
3mm(0.12)

RM
(Right
margin)
(min.)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)

TM
(Top margin)
(min.)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)
3mm(0.12)

BM
(Bottom
margin)
(min.)
14mm(0.54)
14mm(0.54)
14mm(0.54)
14mm(0.54)
14mm(0.54)
14mm(0.54)

PW

LM

RM

TM

PL

Printable Area

BM

Figure 1-3. Printing Area for Cut Sheet

Rev. A

1-7

EPSON Stylus Color 600

1.2.4.2 Envelope
The table and figure below show the printable area for envelopes.
Table 1-8. Envelope
Paper Size

LM
(Left Margin)
(min.)
3mm (0.12)
3mm (0.12)
3mm (0.12)

#10
DL
C6

RM
(Right Margin)
(min.)
28mm (1.10)
7mm (0.28)
3mm (0.12)

TM
(Top Margin)
(min.)
3mm (0.12)
3mm (0.12)
3mm (0.12)

BM
(Bottom Margin)
(min.)
14mm (0.55)
14mm (0.55)
14mm (0.55)

RM

LM

TM

Printable area

BM

Figure 1-4. Printing Area for Envelope

1-8

Rev. A

Chapter 1 Product Description

1.2.5 Environmental Condition

Temperature
Operating
Non-operating




:10 - 35C (Refer to the figure below for condition)

:-20 - 60C (with shipment container)

Note) Storage should be within one month at 40C and 120 hours at 60C.

Humidity
Operating




:20% - 80% RH
(without condensation. Refer to the figure below for condition)
:5% - 85% RH
(without condensation and with shipment container)

Non-operating

Humidity
(% RH)
80%

Guaranteed range

55%

20%

10C
(50F)

27C
(80F)

35C
(95F)

C
(F)

Figure 1-5. Temperature/Humidity of Range

Resistance to shock
Operating
Non-operating




:1G, within 1 ms (X,Y,Z directions)

:2G, within 2 ms (X,Y,Z directions/with shipment container)

Resistance to vibration
Operating
:0.15G, 10`55Hz (X,Y,Z directions)
Non-operating
:0.50G, 10`55Hz (X,Y,Z directions/with shipment container)




Note) 1. During non-operating, make sure that the head is capped.

2. During the transport, make sure that the head is capped and ink cartridge is installed to the
printer.
3. If the head is not capped at the power-off state, turn the power on with the ink cartridge
installed and turn off the power after confirming that the head is correctly capped.
4. Ink will be frozen under -4C environment, however it will be useable after placing it more than
3 hours at 25C.

Rev. A

1-9

EPSON Stylus Color 600

1.2.6 Ink Cartridge Specifications

1.2.6.1 Black Ink Cartridge
Table 1-9. Black Ink Cartridge Specifications
Item
Type
Color
Print capacity
Validity
Environmental
conditions

Specifications
Black Ink Cartridge(Code: S020093)
Black
540 pages / A4 (ISO/IE10561 Letter Pattern at 360 dpi)
2 years (sealed in package) / 6months(out of package)
Temperature
Storage
:-20 - 40C (within a month at 40C)
Packing storage
:-30 - 40C (within a month at 40C)
Transit
:-30 - 60C (within 120 hours at 60C and within a
month at 40)
Humidity
5% - 85% (without condensation)
Resistance to vibration
Sealed in package
:5 - 55Hz
Acceleration
:Less than 29.4m/s (3G)
Direction
:X, Y, Z direction
Time
:1 hour
Drop
Sealed in package:
Dropping height
:Less than 0.80m
Direction
:Drop the package facing the bottom, sides and one
edge down.
Out of package:
Dropping height
:Less than 1.50m
Frequency
:Once
19.8mm(W) x 52.7(D) x 38.5mm(H)
Total ink cartridge
:54g
Total ink
:16.4}0.5g (Amount in the ink cartridge)
Consumable ink
:More than 12.1g(Useable ink quantity until ink ends)

















Dimension
Weight










Note) 1. Ink cartridge can not re-fill, only ink cartridge is prepared for article of consumable.
2. Do not use the ink cartridge which is passed away the ink life.
3. Ink will be frozen under -4environment, however it will be usual after placing it more than 3
hours at room temperature.
19.8

52.7

51.2

38.5

18.3

Figure 1-6. Ink Cartridge (Black)

1-10

Rev. A

Chapter 1 Product Description

1.2.6.2 Color Ink Cartridge

Table 1-10. Color Ink Cartridge Specification
Item
Type
Color
Print capacity
Validity
Environmental
conditions

Specifications
Color Ink Cartridge (Code: S020089)
Magenta/Cyan/Yellow
300 pages / A4 (360 dpi, 5% duty each color)
2 years (sealed in package) / 6months(out of package)
Temperature
Storage
:-20 - 40 (within a month at 40)
Packing storage
:-30 - 40 (within a month at 40)
Transit
:-30 - 60 (within 120 hours at 60and within a
month at 40)
Humidity
5% - 85% (without condensation)
Resistance to vibration
Sealed in package
:5 - 55Hz
Acceleration
:Less than 29.4m/s (3G)
Direction
:X, Y, Z direction
Time
:1 hour
Drop
Sealed in package :
Dropping height
:Less than 0.80m
Direction
:Drop the package facing the bottom, sides and one
edge down.
Out of package:
Dropping height
:Less than 1.50m
Frequency
:Once
42.9mm(W) x 52.7(D) x 38.5mm(H)
Total ink cartridge
:68g
Total ink
:13.3}0.5g (Amount in the ink cartridge)
Consumable ink
:More than 10.1g/each color (Useable ink quantity until
ink ends)

















Dimension
Weight










Note) 1. Ink cartridge can not re-fill, only ink cartridge is prepared for article of consumable.
2. Do not use the ink cartridge which is passed away the ink life.
3. Ink will be frozen under -4environment, however it will be usual after placing it more than 3
hours at room temperature.

43.2

51.2

52.7

42.9

38.5

41.4

Figure 1-7. Ink Cartridge (Color)

Rev. A

1-11

EPSON Stylus Color 600

1.2.7 Physical Specification

[Dimension]

:429mm(W) x 234mm(D) x 162mm(H)

:429mm(W) x 695mm(D) x 309mm(H) with extended stacker and paper support.

[Weight]

:5.2Kg

695mm (Max)

309mm

429mm

Figure 1-8. Dimension

1-12

Rev. A

Chapter 1 Product Description

1.2.8 Electric Specification











[120V] Version
[Rated voltage]
[Input voltage range]
[Rated frequency range]
[Input frequency range]
[Rated current]
[Power consumption]











[220 - 240V] Version

[Rated voltage]
[Input voltage range]
[Rated frequency range]
[Input frequency range]
[Rated current]
[Power consumption]

[Insulation Resistance]
[Dielectric strength]

[Insulation Resistance]
[Dielectric strength]

:AC120V
:AC103.5 - 132V
:50 - 60Hz
:49.5`60.5Hz
:0.4A(Max. 0.5A)
:Approx.15W(ISO/IEC 10561 Letter pattern)
(Energy Star compliant)
:10M ohms min.(between AC line and chassis, DC500V)
:AC1000 V rms. 1 minute or AC1200Vrms. 1 second
(between AC line and chassis)

:AC220V - 240V
:AC198 - 264V
:50 - 60Hz
:49.5 - 60.5Hz
:0.2 A(Max. 0.3A)
:Approx.15W(ISO/IEC 10561 Letter pattern)
(Energy Star compliant)
:10M ohms min.(between AC line and chassis, DC500V)
:AC1500 V rms. 1 minute (between AC line and chassis)

1.2.9 Reliability

Total print volume

Print head life

:10,000 pages(A4, letter)

:2000 million dots/nozzle

1.2.10 Safety Approvals

[120V version]
Safety standard

EMC

[220 - 240V]
Safety standard
EMC

:UL1950 with D3
:CSA22.2 No.950 with D3
:FCC part 15 subpart B class B
:CSA C108.8 class B

:EN 60950(VDE and NEMKO)

:EN55022(CISPR Pub.22) class B
:AS/NZS 3548 class B

1.2.11 Acoustic Noise

Noise Level

:Approx.45 dB(A) (According to ISO 7779)

1.2.12 CE Marking
[220 - 240V version]
Low voltage Directive 73/23/EEC :EN60950
EMC Directive 89/336/EEC
:EN55022 Class B
:EN61000-3-2
:EN61000-3-3
:EN50082-1
:IEC801-2
:IEC801-3
:IEC801-4

Rev. A

1-13

EPSON Stylus Color 600

1.2.13 Printer Language and Emulation

Printer Language

ESC/P control codes










1-14

:ESC/P2
:EPSON Remote





General Operation:
Initialize Printer
Unidirectional Printing
CSF Mode Control

: ESC @
: ESC U
: ESC EM






Paper feeding:
Form Feed
Line Feed
Line Spacing
Carriage Return

: FF
: LF
: ESC 0, ESC 2, ESC 3, ESC +
: CR





Page format:
Page Length
Left / Right Margin
Top / Bottom Margin

:ESC (C, ESC C, ESC C0

:ESC Q, ESC1
:ESC (c, ESC N, ESC O







Printer position motion:

Horizontal Print Position
Vertical Print Position
Tab Horizontally
Tab Vertically
Advance paper

:ESC $, ESC\
:ESC(V, ESC (v
:ESC D, HT
:ESC B, VT
:ESC J








Font Selection:
Typeface
Pitch and Point
Pitch
Italic Font
Bold Font
Master Select

:ESC k, ESC x
:ESC X
:ESC P, ESC M, ESC g, ESC p
:ESC 4, ESC 5
:ESC E, ESC F
:ESC!










Font enhancement:
Double-Width
Condensed
Double-height
Double-Strike
Super / Subscript
Underline
Line / Score
Character Style

:ESC W, DC4, SO
:DC2, SI
:ESC w
:ESC G, ESC H
:ESC T, ESC S
:ESC:ESC(:ESC q





Spacing:
Intercharacter Space
HMI
Define Unit

:ESC Space
:ESC c
:ESC (U

Character handling:
Character Table
International Character
User-Defined Characters
Upper Control Codes
Print Data as Characters

:ESC t, ESC (t
:ESC R
:ESC %, ESC &, ESC:
:ESC 6, ESC7
:ESC(^







Rev. A

Chapter 1 Product Description








Rev. A

Bit image:
Bit Image

:ESC*








Graphics:
Graphics Mode
Raster Graphics
Microweave control
Dot size control
Horizontal Position
Printing Speed

:ESC (G
:ESC.
:ESC (i
:ESC (e
:ESC (\
:ESC(s

Printing mode:
Printing mode

:ESC (K

Color:
Printing Color

:ESC r, ESC (r

EEPROM control
EEPROM control

:ESC

1-15

EPSON Stylus Color 600

1.3 Interface
This printer provides both parallel and serial interface as standard.

1.3.1 Parallel Interface (Forward Channel)

[Transmission mode]
[Synchronization]
[Handshaking]
[Signal level]
[Adaptable connector]

:8 bit parallel, IEEE-1284 compatibility mode

:By /STROBE pulse
:BY BUSY and /ACKNLG signal
:TTL compatible level
:57-30360 (amphenol) or equivalent

BUSY signal is set high before setting either/ERROR low or PE high and held high until all these signals
return to their inactive state.
BUSY signal is at high level in the following cases.
During data entry (see Data transmission timing)
When input data buffer is full
During -INIT signal is at low level or during hardware initialization
During printer error (See /ERROR signal)
When the parallel interface is not selected.







ERROR signal is at low level when the printer is in one of the following states.
Printer hardware error (fatal error)
Paper-out error
Paper-jam error
Ink-out error






PE signal is at high level during paper-out error.

Table 1-11 shows the signal and connector pin assignments for parallel interface(forward channel*1). In
case of these signals, twist pair line is used and returning side is connected to signal GND (*1). Forward
channel is the mode when the ordinary data such as print data is sent from the PC to the printer.
Table 1-11. Signal and Connector Pin Assignment for Parallel Interface
Pin No.
1

Signal Name Return GND pin

/STROBE
19

I/O
In

2-9

DATA0-7

20-27

In

10

/ACKNLG

28

Out

11

BUSY

29

Out

12
13

PE
SLCT

28
28

Out
Out

14
31

/AFXT
/INIT

30
30

In
In

29
30
-

Out
In
Out
Out
-

32
/ERROR
36
/SLIN
18
Logic H
35
+5V
17
Chassis GND
16,33,19-30
GND
15,34
NC

Functional Description
The strobe pulse. Read-in of data is performed at
the falling edge of this pulse.
The DATA0 through DATA7 signals represent
data bits 0 to 7, respectively. Each signal is at
high level when data is logical 1 and low level
when data is logical 0.
This signal is a negative pulse indicating that the
printer can again accept data.
A high signal indicates that the printer cannot
receive data.
A high signal indicates paper-out error.
Always at high level when the printer is powered
on.
Not used.
The falling edge of a negative pulse or a low
signal on this line causes the printer to initialize.
Minimum 50 us pulse is necessary.
A low signal indicates printer error condition.
Not used.
Pulled up to +5V via 3.9K ohm resistor.
Pulled up to +5V via 3.3K ohm resistor.
Chassis GND.
Signal GND.
Not connected.

Note) I/O refers to the direction of signal flow from the printers point of view.
1-16

Rev. A

Chapter 1 Product Description

1.3.2 Parallel Interface (Reverse Channel)

[Transmission mode]
[Synchronization]
[Handshaking]
[Data transmission timing]
[Signal level]

:IEEE-1284 nibble mode

:Refer to the IEEE-1284 specification
:Refer to the IEEE-1284 specification
:Refer to the IEEE-1284 specification
:IEEE-1284 level 1 device
:TTL compatible level
[Adaptable connector]
:57-30360 (amphenol) or equivalent
[Extensibility request]
:The printer responds affirmatively when the extensibility request values
are 00H or 04H, that mean;
00H :Request Nibble Mode Reverse Channel Transfer.
04H :Request device ID; Return Data using Nibble Mode Rev Channel
Transfer.
Note) The printer sends following device ID string when it is requested.
Table 1-12. Device ID Description
00H
MFG
CMD
MDL
CLS




3CH
EPSON
ESCPL2,BDC
Stylus[SP]Color[SP] 600
PRINTER

Contents
Production Maker
Command system
Model name
Class

[00H] denotes a hexadecimal value of zero. MDL value depends on the EEPROM setting.
MDL value depends on the EEPROM setting. Model name can be changed by
changing a certain address in the EEPROM.

The table below shows pin assignment for reverse channel(*3). In these case of signals, twist pair line is
used and returning side is connected to Signal GND. (*3):Reverse channel is the mode that any data is
transferred from the printer to the PC.
Table 1-13. Pin Assignment for Reverse Channel
Pin
Signal Name
Return I/O
Functional description
No.
GND pin
1
HostClk
19
In Host clock signal.
2-9
Data0-7
20-27
In The DATA0 through DATA7 signals represent data bits 0
to7, respectively.
Each signal is at high level when data is logical 1 and low
level when data is logical 0. These signals are used to
transfer the 1284 extensibility request values to the
printer.
10
PrtClk
28
Out Printer clock signal.
11
PtrBusy, Data Bit-3,7
29
Out Printer busy signal and reverse channel transfer data bit
3 or 7.
12 AckDataReq, DataBit-2,6
28
Out Acknowledge data request signal and reverse channel
transfer data bit 2 or 6.
13
Xflag, DataBit-1,5
28
Out X-flag signal and reverse channel transfer data bit 1 or 5.
14
HostBusy
30
In Host busy signal.
31
/INIT
30
In Not used.
32
/DataAvail, DataBit-0,4
29
Out Data available signal and reverse channel transfer data
bit 0 or 4.
36
1284-Active
30
In 1284 active signal.
18
Logic-H
Out Pulled up to +5V via 3.9K ohm resister.
35
+5V
Out Pulled up to +5V via 3.3K ohm resister.
17
Chassis GND
- Chassis GND.
16,33
GND
- Signal GND.
19-30
15, 34
NC
- Not connected.

Note) I/O refers to the direction of signal flow from the printers point of view.
Rev. A

1-17

EPSON Stylus Color 600

Following lists Notes when using Parallel Interface.

Return GND pin in the table means twist pair return and is used for all control signals except for
Logic H,+5V, Chassis, GND and NC. In this twist pair return, returning side is connected to
GND (16,33, 19-30 pin) for twist pair return. Also, these cables are shielded wires and it is
effective to connect to each chassis GND in the PC and printer for electrostatic noise.
Conditions for Interface are based on TTL level. Rise and fall time should be within 0.2s.
Refer to the figure 1-9 for transmission timing of each signals.
Do not perform data transmission ignoring /ACK or BUSY signal. (Perform the data transmission
after confirming that /ACK and BUSY signals are Low.)
It is possible to perform the printing test including interface circuit without using equipment from
outside when 8-bit data signal(20-27 pin) is set to appropriate word code and connect them
forcefully to /ACK and /STRB.

[Data Transmission Timing for Forward Channel]

Data

Byte Data n

Byte Data n+1

Thold

/STROBE
Tsetup

Tnext

Tstrb

BUSY

/ACKNLG

Tready

Tbusy

Treply

Tack

Tnbusy

Figure 1-9. Parallel Interface Timing Chart(Forward Channel)

Table 1-14. Timing Parameters and Value

Note)

Parameter
Minimum
tsetup
500ns
thold
500ns
tstb
500ns
tready
0
tbusy
--tt-out*
--tt-in**
--treply
0
tack
500ns
tnbusy
0
tnext
0
*: Rise and fall time of every output signals.
**: Rise and fall time of every input signals.

Maximum
--------500ns
120ns
200ns
--10us
-----

Table 1-15. Typical Time of Tack

Parallel I/F mode
High speed
Normal speed

1-18

Typical time of tack

2us
4us

Rev. A

Chapter 1 Product Description

[Signal level: TTL compatible (IEEE-1284 level 1 device)]
Table 1-16. Signal Level
Parameter
Minimum
Maximum
Condition
VOH*
--5.5V
VOL*
-0.5V
--IOH*
--0.32mA
VOH = 2.4V
IOL*
--12mA
VOL = 0.4V
CO
--50pF
VIH
--2.0V
VIL
0.8V
--IIH
--0.32mA
VIH = 2.0V
IIL
--12mA
VIL = 0.8V
CI
--50pF
Note) *: A low logic level on the Logic H signal is 2.0V or less when the printer is
powered off and this signal is equal or exceeding 3.0V when the printer is
powered on. The receiver shall provide an impedance equivalent to
7.5K ohm to ground.
[Data Transmission Timing for Reverse Channel]
The figure below shows timing chart of Parallel Interface Reverse channel.

Virtual Busy Status

Virtual Busy Status

Figure 1-10. Parallel Interface Timing Chart(Reverse Channel)

1.3.2.1 Prevention Hosts from Data Transfer Time-out

Generally, hosts abandon data transfer to peripherals when a peripheral is in the busy state for dozens of
seconds continuously. To prevent hosts this kind of time-out, the printer receives data very slowly, several
bytes per minute, even if the printer is in busy state. This showdown is started when the rest of the input
buffer becomes several hundreds of bytes. Finally, the printer is in the busy state continuously when the
input buffer is full.

Rev. A

1-19

EPSON Stylus Color 600

1.3.3 Serial Interface

[Standard]
[Synchronization]
[Bit Rate]
[Handshaking]
[Word Format]

[Connector]
[Recommended Cable]

:Based on RS-423
:Synchronous
:Approx. 900Kbps
:X-ON/X-OFF, DTR Protocol
:Data Bit = 8 bits
:Parity Bit = None
:Start Bit = 1 bit
:Stop Bit = 1 bit
:8-pin mini-circular connector
:Apple System Peripheral-8 Cable
(Part #:
M0197)
Table 1-17. Pin Assignment

Pin No.
1
2
3
4
5
6
7
8

Signal Name
SCLK
CTS
TXDSG
RXDTXD+
DTR
RXD+

I/O
O
I
O
I
I
O
O
I

Description
Synchronous clock signal
Clear To Send
Transmit Data (-)
(Signal Ground)
Receive Data (-)
Balanced Transmit Data (+)
Data Terminal Ready
Balanced Receive Data (+)

Table 1-18. X-ON/X-OFF and DTR Status

State
Busy
Ready

1-20

Buffer Space
Less than 3072 bytes
More than 5120 bytes

X-ON/X-OFF
Send X-OFF code
Send X-ON code

DTR
OFF
ON

Rev. A

Chapter 1 Product Description

1.4 Control Panel

Since EPSON Stylus Color 600 does not require many buttons since printer driver can start various
settings and motions. Therefore, there are only 2 non-lock type push switches, 1 lock type push switch
and 4 LEDs.
Following figure shows control panel of EPSON Stylus Color 600.
Power LED

Paper out LED

Ink out(Black)LED
Ink out(CMY)LED

Cleaning Switch
(Ink maintenance)

Load/Eject switch Power switch

Figure 1-11. Control Panel

1.4.1 Indicators

Power
Lights when the operate switch is ON, and AC power is supplied.
Paper out
Lights during the paper-out condition, and blinks during the paper-jam condition.
Ink Out (Black)
Lights during no Black ink condition, and blinks during the Black ink low condition.
Ink Out (Color)
Lights during no Color ink condition, and blinks during the Color ink low condition.

Rev. A

1-21

EPSON Stylus Color 600

1.4.2 Panel Functions

Table 1-19. Panel Function
Switch
Load/Eject
(Pushing within 0.5 seconds*)

Function

Loads or Eject the paper.

When the carriage is on the Ink Cartridge change position, return the
carriage from Ink Cartridge change position.
Load/Eject
Starts the Ink Cartridge change sequence.**
(Pushing for 2 seconds*)
Moves the carriage to cartridge change position.
Cleaning
Starts the Head Cleaning sequence. ***
(Pushing for 2 seconds*)
In the condition of Ink Low or Ink Out or No Ink Cartridge starts
the Ink Cartridge change sequence.**
Cleaning
When carriage is on the Ink Cartridge change position, return carriage
(Pushing within 2 seconds*)
from Ink Cartridge change position.
Note) *: 3 seconds is required at the Users manual.
**: This function is not available in printing status.
***: The time to complete the sequence may vary depending on the printers status.
Panel Functions with Power ON
Table 1-20. Panel Function with Power ON
Switch
Load/Eject
Cleaning
Load/Eject
+
Cleaning

Function
Starts status printings.**
Enter the Default Setting mode
Enters the particular settings mode. (Factory use only.)
To enter the particular settings mode, it is necessary to push
followings switch while Paper Out LED is blinking.(It blinks about 5
seconds)
Note) **: status printings prints firmware version, ink counter, selected code page and nozzle check
patterns.

Particular setting mode

Table 1-21. Particular Setting Mode
Switch
Function
Load/Eject
Initialize EEPROM *** and reset Timer IC.
Note) ***: Refer to EEPROM map.

1-22

Rev. A

Chapter 1 Product Description

By performing a particular setting mode, Maintenance error can be cleared and certain addresses of
EEPROM can also be reset.

Maintenance Error Clear

[Step 1]
[Step 2]

Turn the printer on while holding down Load/Eject and Cleaning switches at the same time.
(By operating this performance, the Paper Out LED starts blinking.)
Push the Load/Eject switch while the Paper Out LED is blinking (5 seconds).

Following shows the lists that will be cleared by this performance.

Clear the value of Ink Counter

Clear Time IC
Initialization of I/F selection (returns to AUTO)

WARNING

EPSON Stylus Color 600 does not have EEPROM All Clear function like other printers. If the
printer does not function well and falls into fatal error condition, replace the main board to see if
the problem is rectified. (Refer to Chapter 4 Adjustment when you replace the main board since
some adjustments will be necessary.)
Be sure to replace a waste ink pad in the printer enclosure with a new one after you perform
Maintenance error clear operation.

1.4.3 Printer Condition and Panel Status

The table below shows printer condition and panel status. Since this table shows various error status and
also present printer status, you can judge appropriate repair ways from this table.
Table 1-22. Printer Condition and Panel Status
Printer status
Power
Power on condition
Ink sequence
Ink Cartridge change mode
Data processing
Paper Out
Paper jam condition
No Ink cartridge or Ink end(black)
Ink level low(black)
No Ink cartridge or Ink end(color)
Ink level low(color)
Enter EEPROM and Timer IC reset

On
Blink
Blink
Blink
---------------

Maintenance request
Fatal error

Blink
Blink

Indicators
Ink Out
Ink Out
(Black)
(Color)
--------------------Off
Off
On
--Blink
----On
--Blink
On
On
(1 second
(1 second
only)
only)
Blink
Blink
On
On

Priority
Paper Out
--------On
Blink
--------On
(1 second
only)
Blink
Blink

9
6
5
8
4
3
7
7
7
7
--

2
1

Note) means no changes.

Rev. A

1-23

EPSON Stylus Color 600

1.5 Error Status

When following status occur, the printer goes to the error status and stops taking data, setting the
/ERROR signal in the interface as Low, and Busy signal as High. At this time, the printer goes to non
printable status. Refer to section 1.4.2 for more details of LED Panel indicators during the various error
status.

1.5.1 Ink Out

When the printer runs out the most part of the ink of any one color, it warns ink-low and keeps printing.
When the printer runs out the whole ink of any one color, it stops printing and indicates ink-out error. User
is requested to install a new ink-cartridge in this state. An ink-cartridge once taken out should never be
used again. Re-installation of the cartridge not filled fully upsets the ink level detection and may cause a
serious problem in the print head as a result.

WARNING

Never use the ink cartridge once taken out from the printer.

Following explains the reason of the above warning.

After the cartridge is once taken out, airs come in from the ink supply hole located at the top of
cartridge and becomes bubbles, and they are absorbed into the head during printing performance.
Therefore, the head will be unable to discharge the ink properly. Also, inevitable entering of bubbles
when installing a new ink cartridge can be absorbed to ink itself since the ink itself in the cartridge is
deaerated during the production process. However, this absorbing ability can last only about one hour
after the cartridge is installed.
Even after the bubble absorbing ability described above stops, there is no worry about entering
bubbles as long as the ink cartridge is being installed to the printer. However, if the ink cartridge which
does not have absorbing ability any more is once removed from the printer, new coming bubbles into
the cartridge will never disappear naturally. These bubbles may cause not only printing malfunction but
also thickening ink. This thickened ink goes into the head and clogs ink path in the head or nozzle and
may cause serious head damage.
As standard specification for EPSON Stylus Color 600, ink consumption counter is reset when the ink
cartridge is removed. If an ink cartridge is removed and re-installed unnecessarily the value on the ink
consumption monitor which the user can check will be wrong and printer may keep printing even
though the ink cartridge is installed empty. This may cause head damage.

1.5.2 Paper Out

When printer fails to load a sheet after power on operation including timer-cleaning is done and Load/Eject
button on the FF command or operation panel is pressed, it goes paper out error.

1.5.3 Paper Jam

When printer fails to eject a sheet even after feeding motion is completed or Load/Eject button on the FF
command or operation panel is pressed, it goes paper jam error.

1-24

Rev. A

Chapter 1 Product Description

1.5.4 No Ink-Cartridge Error

Following reasons can be the causes when printer goes this error mode.

When the printer is turned on for the first time.

(This is a normal error state and it returns to the normal state after installing an ink cartridge
according to the ink cartridge exchange operation.)

Ink cartridge exchange operation is done correctly. After the position of carriage is moved by
exchange operation, if the cleaning switch is pushed without installing ink cartridge or if the
carriage returns to the home-position automatically without doing any operation, it is considered as
handling mistake. However, it returns to normal state by performing ink exchange operation again
and installing cartridge correctly.

If No ink-cartridge error appears even after the ink cartridge is installed, the printer must be
something wrong and around the sensor area in the carriage need to be repaired.

If sometimes printer can print normally but also sometimes No ink-cartridge error appears, the
printer must be something wrong. (Same reason as above)

1.5.5 Maintenance Request

When the total quantity of ink wasted through the cleanings and flushing reaches to the limit, printer
indicates this error and stops. The absorber in the printer enclosure is needed to be replaced with new
one by a service person. The ink quantity that is absorbed by the absorber (waste ink pad) is monitored by
the software counter as total ink counter. This counter is added by point system and absorbers
maximum ability is set at the following reference value.
29500 X 0.012 ml = Approximately 301ml




1-point = 0.0102 ml (the value which is multiplied evaporating rate and 1-dot ink weight 0.02
ml)
29500 = Maximum point number (Maintenance error threshold)

However, considering dispersion of ink absorbing quantity and the number of using nozzles, ink total value
is calculated by the following formula.
301 X 1.1/63% = 526ml (but up to 532ml can be retained)

WARNING
When you perform self- test after completing repairs, it is possible to check the present value of total
ink counter and ink discharge conditions from all nozzles by performing status printing in the built-in
function. Therefore, make sure that the printer has enough value of total ink counter (if the number is
close to 29500 or not). If there is not enough value, the service man is required to judge if it is
necessary to clear EEPROM after replacing the absorber (waste ink pad) or not. Refer to section 1.3.1
if you need to perform EEPROM Clear.

1.5.6 Fatal Errors

When printer detects fatal errors such as carriage control error or CG access error, it goes to this error
mode. Refer to followings for each error.

Carriage control Error: Parallel adjustment malfunction, Home-position malfunction, Timing belt
tension malfunction, shortage of lubricant on the carriage guide shaft, etc.
CG Access Error:

Rev. A

Short circuit, etc.

1-25

EPSON Stylus Color 600

1.6 Printer Initialization

EPSON Stylus Color 600 has three kinds of initialization methods. Following explains each initialization.

Power-on initialization
This printer is initialized when turning the printer power on, or printer recognized the
cold-reset command (remote RS command). When printer is initialized, following action is
performed.






Initializes printer mechanism.

Clears input data buffer.
Clears print buffer.
Sets default values.

Operator initialization
This printer is initialized when turning the printer power on again within 10 seconds from last
power off, or printer recognize the /INIT signal (negative pulse) of parallel interface. When
the printer is initialized, following action is performed.







Cap the printer head.

Eject a paper.
Clears input data buffer.
Clears print buffer.
Sets default values.

Software initialization
The ESC@ command also initialize the printer. When printer is initialized, following action is
performed.




Clears print buffer.

Sets default values.

1.6.1 Initialization Settings

EPSON Stylus Color 600 initializes following settings when the initialization is performed. Also, if the user
changes the settings in the Panel setting, Default setting or Remote command setting, values or settings
which are possible to be stored are initialized as initialization settings.








1-26

Page position
Line spacing
Right margin position
Left margin position
Character pitch
Printing mode

:Page heading location as present paper location

:1/6 inch
:80 lines
:first line
:10CPI
:Text mode (Not Raster graphics mode)

Rev. A

Chapter 1 Product Description

1.7 Main Components

EPSON Stylus Color 600 has following major units. Also, it is one of the major characteristics that the
bottom of the Printer mechanism plays the role as lower case at the same time.

Upper case
Printer Mechanism
C200 MAIN Board (Main control circuit board)
C206 PSB/PSE Board (Power supply circuit board)
C206 PNL Board (Control panel circuit board)

1.7.1 Printer Mechanism

Unlike EPSONs previous ink jet printer mechanisms, one of the major characteristics of EPSON Stylus
Color 600 is that the printer has no Engage/Disengage mechanism in order to change over pump
mechanism and paper feeding mechanism. Instead, however, this change-over control is done by the
distinction between turning direction of PF motor and position of present carriage unit. Also, another major
characteristic is that print head is changed to be one unit combined with black and CMY. Nozzle
configuration for black is 64 nozzles (the nozzle pitch of each column is 90dpi and between two
consecutive nozzles in number (e.g. #1 and #2) is 180dpi). On the other hand, CMY nozzle has 32 nozzles
(90dpi) for each color. Following figure shows exterior of mechanism.

CR Motor

Carriage

Control Panel

Hopper
(Exit paper tray)
PF Motor
*ASF is not shown in the above figure.
Figure 1-12. Exterior view of the Printer Mechanism

Rev. A

1-27

EPSON Stylus Color 600

1.7.2 C200 MAIN Board

The C200 MAIN board controls whole mechanism operations and a data processing operation. Most of
the functions of the circuit are integrated into single ASIC; E05B43YA (IC2) and this makes the board
design very simple and reliable.
IC7
Printhead Driver

IC15
PF Motor Driver

IC14
CR Motor Driver

IC2
ASIC
(E05B43YA)
IC1
CPU
(TMP95C0618F)

Parallel I/F(CN1)

IC5
DRAM(4MBit)

Serial I/F (CN2)

IC3
PROM(4MBit)
IC6
Mask ROM (CG)

Lithium Battery

Figure 1-13. Exterior view of C200 Main Board

1-28

Rev. A

Chapter 1 Product Description

1.7.3 C206 PSB/PSE Board

The C206 PSB/PSE board is a switching regulator type power supply unit and constantly supplies stable
logic and power voltages to the printer mechanism and the main control board. Also, since this C206
PSB/PSE board has the power switch in the secondly side of the circuit, it is possible to keep supplying
electricity to the C200 MAIN control board for 30 seconds even after the power switch is turned off. Using
this time difference, even when mis-operation is done by the user such as turning off the power during the
middle of printing work, it prevents unexpected trouble with the printhead from occurring, by transferring
the printhead to the cap position before complete shut down. The C206 PSB Board is for AC100 - 120V
input voltage and the C206 PSE Board is for AC220 - 240V input voltage.
AC input (CN1)

Q1
FET (Switching)

Power line to
C200 MAIN/Mechanism
(CN2)

FUSE (F1)

PC1
Photo-coupler

Figure 1-14. Exterior view of C206 PSB Power Supply Board

1.7.4 C206 PNL Board

The C206 PNL board is located in the panel case where is in the right bottom of the front of printer and
consists of 3 switches, 4 LEDs.

Figure 1-15. Exterior view of C206 PNL Board

Rev. A

1-29