RTWP Troubleshooting

Security Level:
RTWP Troubleshooting Guide
Zhang Junjie (employee ID: 00107307) Liu Qiong (employee ID: 54780)
www.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Contents
RTWP Concept and Impacts on the System Overview of RTWP Sampling Points Common RTWP Problems and Troubleshooting Procedure
Traffic statistics decision RTWP problem description and handling suggestions 2 ms RTWP analysis
Overview Troubleshooting Methods

Configuration problems Interference detection (intermodulation problems, external problems) Network planning problems Traffic capacity and improvement measures
Appendix 1: Method of Collecting Tracing Logs Routinely
Huawei Confidential
Page 2
RTWP
What is RTWP? RTWP is short for received total wideband power, which is used in UMTS. It specifies the total energy in the uplink 3.84 MHz band, including the available signals, noise, and interference. Normal range of RTWP Thermal noise is the noise floor in the nature. The actual noise is greater than or equal to thermal noise. Therefore, thermal noise is also called background noise. The thermal noise in the 3.8 4 MHz band is -108 dBm. The thermal noise on the antenna connector deteriorates and becomes -106 dBm after being amplified by the receiver. As specified in 3GPP protocols, the RTWP accuracy is +/-4 dB. That is, when there are no uses and no external interference, the RTWP should be -106 dBm +/-4 dB. When there are uses, the RTWP increases.
PN = KTB + NF, where, K = Boltzmann constant, T = 290 K (room temperature)
B = RF carrier bandwidth (Hz) = 3.84 MHz NF: noise factor of the RF system The PN is about -106 dBm at room temperature.
Huawei Confidential
Page 3
RTWP Measurement
RTWP is defined as the energy on the antenna connector. However, the energy is too weak. The energy can be measured only after being amplified by the receiver. RTWP = energy amplified by the receiver amplified multiples (gain) If the configurations and use methods are correct, the actual amplified multiples (actual gain) is consistent with the preset amplified multiples (theoretical gain). Therefore, even on the DSP port, the RTWP can be measured correctly. If the configurations and use methods are incorrect, the actual gain is different from the theoretical gain. As a result, the RTWP is incorrect.
MRFU receiver architecture
RTWP=P_in= P_out - Gain
P_out P_in
Huawei Confidential
Page 4
What Does the RTWP Represents?

On the UMTS system, when the RTWP is high, Uplink coverage is restricted, and cell edge users (CEUs) cannot access the network or dropped from the network. Network capacity is restricted, and user experience becomes poor. KPIs deteriorate, for example, RRC access success rate, CS/PS call drop rate, and throughput rate
Huawei Confidential
Page 5
Controlling the RTWP on the Network Side

Power control policies Fast power control policy: The 1500 times/s inner-loop power control policy allows the UE to transmit at the smallest power when the QoS is ensured. Softer combiner policy: Intra-frequency neighboring cells use the softer combing policy to increase the uplink combining gain. Optimum channel power configuration ratio: The power configuration ratios of control channels and data channels at the physical layer are optimum. Time/capacity tradeoff: HSUPA retransmission combining gain reduces the transmit power of the UE. Overload protection policy: When RTWP is high, lower the transmit power of low-priority users to ensure the conversation quality of high-priority users. HSUPA scheduling HSUPA scheduling is performed according to the cell RoT (RTWP rise). Without considering interference, 75% (6 dB) load threshold is specified. The rate control on HSUPA users from the NodeB is equivalent to power control. Therefore, a higher rate indicates a larger transmit power of the UE. Anti-interference scheduling: identify interference and provide efficient capacity for the system maximally. Interference cancellation (IC) Intra-RAT IC: IC and CCPIC for the physical channels of users in the system RTWP admission
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Page 6
Contents

Huawei Confidential
Page 7
RTWP Sampling Points

In the RAN system, there are multiple RTWP stamping points.
Huawei Confidential
RTWP Sampling Mode

Real-time RTWP tracing on the RNC LMT (average main and diversity RTWP)
Obtain the average RTWP. The detection period ranges from 0.1 second to 300 seconds.
Board RTWP tracing on the NodeB LMT (main and diversity RTWP)
Obtain the main and diversity RTWP.
RTWP tracing on the NodeB LMT (average main and diversity RTWP, supported in RAN13.0)
Obtain the average RTWP.
RNC traffic statistics

Obtain the minimum RTWP, maximum RTWP, and average RTWP.
NodeB CDT
Use a tool to analyze 2 m2 RTWP from the CDT data.
Huawei Confidential
Contents

Huawei Confidential
Page 10
Criteria for Determining an RTWP Problem

The traffic statistics show that the average RTWP is greater than -93 dB. Poor user experience: Web page browsing is slow. Calls cannot be originated, and conversation quality is poor. KPI performance deterioration: access success rate, call drop rate, throughput rate
Huawei Confidential
Page 11
Common RTWP Problems and Troubleshooting Procedure

Main reasons External interference (neighboring cell interference): No.1 problem Configuration (including TMA related configuration): No. 2 problem Antenna feeder intermodulation interference: often available UMTS 850 MHz/UMTS900 MHz Antenna feeder connections (cross connections) Heavy traffic: often available to busy sites Troubleshooting procedure (identify the problem according to the 2G indicators and the following inputs) External interference 2G/3G uplink frequency scanning Preparing the interference map using the Mapinfo Block an area (out of services) to check for RTWP. Configuration Main level and diversity level and uplink/downlink balance class (2G) Main and diversity RTWP (3G) Antenna feeder connections Channel attenuation configuration and RF interconnection configuration Intermodulation interference detection (2G/3G intermodulation interference detection) Main and diversity RTWP (using the tool) RTWP (minimum and average RTWP) and number of 3G users: check the relationship between number of services and RTWP.
Page 12
RTWP Troubleshooting Procedure

After analyzing the RTWP in the traffic measurement data, determine whether the cell RTWP rise is caused by the RAT or external interference. After analyzing the cell RTWP of a single site, identify the possible causes for cell RTWP rise. If the cause analysis of an RTWP rise fails to effectively identify the interference source, collect the 2-ms RTWP data included in the cell CDT data and determine the interference source based on the signal characteristics.
Huawei Confidential
Method 1: Background Noise Rise when No User Is Connected

Key traffic statistics counters
VS.MinRTWP, VS.MeanRTWP, and VS.CellDCHUEs (number of users) If CellDCHUEs is 0, MinRTWP is greater than -106 dBm.
RRU-based distributed cell networking In the RRU-based distributed cell networking, the background noise always rises by N = 10log (N) dB. For example, the background noise of two RRUs rises by 3 dB. Incorrect RF channel configuration If the RTWP (background noise) rises in a relatively stable manner when no user is connected and the RTWP rises according to the increase of the number of users, the RF parameters related to the RF channel may be configured incorrectly, resulting in the abnormal background noise rise. Continuous external interference With the impacts of a stable external interference source, the background noise rises abnormally.
Incorrect value reported from the RRU According to board main and diversity RTWP and cell RTWP, check whether the cell RTWP and board RTWP match. No temperature compensation for 2 ms RTWP
Page 14
Background Noise Rise when No User Is Connected

VS.MinRTWP, VS.MeanRTWP, and VS.CellDCHUEs (number of users)
The green line indicates the MeanRTWP, the yellow line indicates the MinRTWP, and the blue line the CellDCHUEs (number of users in a cell). This figure shows that the RTWP continuously rises by more than 5 dB when no user is connected at night. In this case, the cell is affected by continuous external interference. The causes for the abnormal RTWP rise cannot be the RF channel configuration or the distributed RRU networking because the minimum RTWP of the background noise in the day decreases to a normal value.
This figure shows that the RTWP continuously rises by more than 15 dB when only a few users are connected. In this case, the cell is affected by continuous external interference. In this situation, you cannot determine the relationship between the RTWP and the number of users. Check whether the RF channel parameters are configured correctly.
Huawei Confidential
Page 15
Method 2: No Association Between RTWP Rise and the Number of Users When the Background Noise Is Normal
VS.MinRTWP, VS.MeanRTWP, and VS.CellDCHUEs (number of users) If CellDCHUEs changes, MeanRtwp does not changes with the number of users.
External interference
Including continuous external interference and intermittent interference
Incorrect antenna feeder connections

The cell RTWP fluctuation may indicate the change to the number of users in the neighboring cells. The problem needs to be determined according to the main and diversity RTWP.
Huawei Confidential
Page 16
No Association Between RTWP Rise and the Number of Users When the Background Noise Is Normal
Key traffic statistics counters VS.MinRTWP, VS.MeanRTWP, and VS.CellDCHUEs (number of users)
Intermittent interference 1
Intermittent interference 2
Huawei Confidential
Page 17
Intermittent Interference: No Association Between RTWP Rise and the Number of Users When the Background Noise Is Normal
Key traffic statistics counters VS.MinRTWP, VS.MeanRTWP, and VS.CellDCHUEs (number of users)
Two neighboring cells have two similar RTWP waveforms and receive the same interference.
Huawei Confidential
Page 18
Method 3: The RTWP Changing According to the Number of Users (the More the Number of Users, the Higher the RTWP Is)
VS.MinRTWP, VS.MeanRTWP, and VS.CellDCHUEs (number of users) If CellDCHUEs changes, MeanRtwp changes with the number of users.
Intermodulation interference
The interference of generated intermodulation signals increases with the increase of cell transmit power.
Neighboring cell interference

If the neighboring cell parameters are configured incorrectly, the local cell RTWP rises when users are switched over.
Limited number of users

If the number of users served in a cell exceeds the designed capacity, the number of user accesses increases. As a result, the overall cell RTWP rises.
Page 19
Neighboring Cell Interference: The RTWP Changing According to the Number of Users (the More the Number of Users, the Higher the RTWP Is)
The green line indicates the MeanRTWP, the yellow line indicates the MinRTWP, and the blue line the CellDCHUEs (number of users in a cell). This figure shows that the RTWP rises by more than 10 dB in cells 2 and 3 where many users are served. Such an RTWP rise may be caused if the air interface capacity is limited. In cell 1 where only a few users are served, however, if the RTWP rises more than 10 dB, the neighboring cell interference may exist. HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Page 20
Limited Number of Users: The RTWP Changing According to the Number of Users (the More the Number of Users, the Higher the RTWP Is)
This figure shows that the RTWP rises by about 15 dB when the number of users is large and decreases to the normal value when the number of users is small. In the cell, the number of users is about 50. In this case, the air interface capacity may be limited. HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Page 21
Failing to Directly Specify Whether the Problem Is Caused by External Interference or Internal Interference
If the symptom is not specified, identify the problem according to the main and diversity RTWP.
CellID : 54562 18 16 14 12 10 8 6 4 2 0 -2 0 24 48 72 VS.MeanRTWP 96 VS.MinRTWP 120 144 VS.CellDCHUEs 168 192
Huawei Confidential
Page 22
Contents

Huawei Confidential
Page 23
Symptoms of Main and Diversity RTWP Problems

Common main and diversity RTWP problems
Large difference between the main RTWP and diversity RTWP
1) Same main and diversity RTWP trend 2) Different main and diversity RTWP trends
Too high RTWP in small traffic or unloaded scenarios (greater than -102 dBm) Too small RTWP in small traffic or unloaded scenarios (smaller than -108dBm) RTWP fluctuation
Huawei Confidential
Page 24
Large Difference Between the Main RTWP and Diversity RTWP

1. Main RTWP trend is the same as diversity RTWP trend. The difference between the main RTWP and diversity RTWP is basically the same, and the RTWP fluctuation is consistent. 2. Main RTWP trend is different from diversity RTWP trend, and main RTWP is irrelevant to diversity RTWP. In addition, the RTWP change is not regular. 3. Main RTWP and diversity RTWP are low and remain unchanged.
Huawei Confidential
Page 25
Symptom 1: Main RTWP trend is the same as diversity

RTWP trend, and the difference is above 3 dB.
Huawei Confidential
Page 26
Possible Causes
Case1: Incorrect channel attenuation configuration TMA is configured, but channel attenuation is not configured. TMA is configured, but power is not properly supplied to the TMA. TMA is configured, but power supply is abnormal and TMA is faulty. Channel attenuation is configured correctly, but the configuration does not take effect. Case2: Signals are transmitted from RX_OUTA, and to the antenna connector (ANT_TX/RXA or ANT_RXB) through the splitter. The problem may be caused by incorrect channel attenuation configuration (VHA typical scenario). Case3: Attenuator In the STD, there is a 10-dB attenuator, but it is not connected. The STD drawing is incorrect. The attenuator after the splitter is not figured out.
Huawei Confidential
Page 27
Key Checkpoints
Point 1: Check for the channel attenuation 1. Check the 2G/3G STD for channel attenuation configuration. If the channel attenuation configuration is correct, check whether the configuration takes effect (checking the change in the attenuation in real time by tracing the main RTWP and diversity RTWP). 2. Check for TMA and power supply. a. Check for overcurrent or undercurrent protection. If yes, the power supply is abnormal. The possible cause is: external power supply is available, TMA is not configured, or power supply channel is not configured correctly. b. Power supply is available, and no overcurrent or undercurrent alarm is generated. However, the TMA does not work properly. Check the current for the TMA. Point 2: Check the configuration based on the STD. Point 3: Check for 10 dB attenuation. If there is 10 dB attenuation, check whether the attenuator after the splitter is configured.
Huawei Confidential
Page 28
Symptom 2: Main and diversity receivers have signals,

but their RTWP trends are different (intermodulation).
Huawei Confidential
Page 29
Symptom 2: Main and diversity receivers have

signals, but their RTWP trends are different (cross connections).
Huawei Confidential
Page 30
Possible Causes
Case 1: Intermodulation Interference
1) The 2G main receiver causes intermodulation interference and affects 3G diversity reception. 2) The 3G main receiver causes intermodulation interference and affects 3G main reception.
Case 2: Cross Connections

1) Different sectors cross feeders. Main and diversity receivers of each sectors are not relevant, but main and diversity receivers between the two sectors are relevant.
Case 3: External Interference

1) The interference impacts the main or diversity receiver.
Huawei Confidential
Page 31
Key Checkpoints
Point 1: Check for intermodulation. If intermodulation exists, check the customer interference or Huawei interface (see appendix 2).
1) Conduct idle timeslot tests to check whether 2G interference affects 3G. 2) Conduct simulation load tests to check for 3G interference. For UMTS900 MHz sites, the 2G frequency scanning function can be used.
Point 2: Use the tool to check feeder connections onsite. Point 3: Use the 2G/3G interference scanning function to check whether the main interference level and diversity interference level are consistent.
Huawei Confidential
Page 32
Symptom 3The main or diversity receiver does

not have signals, and their RTWP trends are different.
Huawei Confidential
Page 33
Possible Causes
Case 1: 2G: Single-feeder and double-feeder configurations are incorrect. 3G: The RF intermodulation configuration is incorrect. Case 2: Antenna feeder connections are incorrect.
1) The antenna feeder is not connected. 2) The splitter is faulty. 3) The WRFU is faulty. 4) One channel of the TMA is faulty, and the status is Bypass.
Case 3: In the IBC site, diversity channels are activated mistakenly.

Page 34
Procedure
Case 1: Check whether the RF cross connection configuration is the same as the design in the STD. 1) If signals are designed to be transmitted from the RF cross connection port but non-interconnection is configured, the main or diversity receiver is not connected (-106 dB). 2) If signals are designed to be transmitted from the antenna connector but the RF cross-connection is configured, the main or diversity receiver is not connected (below -112 dB). Case 2: Analyze the fault symptom to identify signal sources without fluctuation and determine the possible points of failure after the transmission through the feeder and RF components. Check connections or replace components to confirm whether the problem persists. Case 3: Contact onsite engineers to check the MSL, confirm the site type, and disable diversity channels.
Huawei Confidential
Page 35
In low traffic scenarios, RTWP > 102 dBm
Huawei Confidential
Page 36
Symptom----Background Noise Rise
Huawei Confidential
Page 37
Possible Causes
Case 1: The TMA is configured, but channel attenuation is not configured, or antenna is too small. Case 2: Continuous external interference causes background noise rise. Case 3: The cell is configured in multi-RRU cascading mode.
Huawei Confidential
Page 38
Actions
Case 1: Set the channel attenuation (MAX: 14 dB) so that RTWP approaches the target value -105 dBm. Case 2: If the STD does not specify TMA or the main RTWP and diversity RTWP cannot approach the target value after the attenuation below 14 dB is configured, use the Rx Frequency Scanning function to perform uplink interference scanning, and submit the result to Tier 2. Case 3: Check the cell configuration for multi-RRU cascading cells.
Page 39
In unloaded scenarios, RTWP < 108 dBm
Huawei Confidential
Page 40
Symptom
Huawei Confidential
Page 41
Possible Causes
Case 1: The TMA is not configured, but the attenuation is configured, resulting in a d decrease in the actual RTWP. Case 2: The TMA is configured, and the attenuation is too high, resulting in a difference between the configured RTWP and the actual RTWP. Case 3: The TMA is configured, and the attenuation is configured correctly. The TMA is not connected properly, or it is faulty and the status is Bypass. Case 4: The RF channel is faulty.
Huawei Confidential
Page 42
Actions
Case 1: Check that no TMA is configured, and set the attenuation to 0. Case 2: Adjust the attenuation so that the RTWP approaches the target value -105 dBm. Case 3: Check for TMA alarms to confirm whether the TMA is faulty.
Huawei Confidential
Page 43
RTWP Fluctuation
Huawei Confidential
Page 44
Symptom----External Interference
RTWP fluctuation is complex. In normal scenarios, RTWP fluctuates slightly. After the following measures are taken, contact R&D engineers if the problem still cannot be identified.
Huawei Confidential
Page 45
Symptom---- Service Signal
Huawei Confidential
Page 46
Possible Causes
Case 1: Antenna feeder connections are incorrect; intermodulation exists. Case 2: External interference exists. Case 3: RTWP rises due to services.
Huawei Confidential
Page 47
Actions
Case 1: Start the load simulation mode in idle hours to check whether the problem is caused by intermodulation. Check antenna feeder connections. Case 2: Check the symptoms of the main and diversity receivers are consistent and whether the symptoms occur in other neighboring cells. If yes, it indicates that external interference exists. Submit the problem to Tier 2. Case 3: Export the traffic statistics data (minimum RTWP/average RTWP) to check whether the RTWP fluctuation is closely related to the number of users. If yes, optimize service parameters.
Page 48
Contents

Huawei Confidential
Page 49
Configuration Problems: Involved Parameters and Commands

TMA attenuation factor configuration and taking effect RAN12.0: DSP RXATTEN; RAN13.0: DSP RXBRANCH TMA power supply switch RAN12.0: DSP ANTCON; RAN13.0: DSP ANTENNAPORT 2G dedicated: TMA switch TMA overcurrent and undercurrent alarm thresholds RF cross connections 2G: Single/Double feeder 3G: RF intermodulation configuration Channel calibration (DSP RTWPINITADJ) RF de-energy R12: DSP RFDESPARAM; R13: LST RRU Desensitivity R12: DSP DESENS; R13: DSP DESENS Tools and commands: Query the TMA current in batches. The configuration script for the TMA switch is shown on the right:
Huawei Confidential
Page 50
Confirming Intermodulation Interference and External Interference

Intermodulation interference For details about how to confirm 2G/3G intermodulation, see the attachment on the right: 2G intermodulation batch processing script: Basic principle: http: //support.huawei.com/support/pages/kbcenter/view/product.do?actionFlag=detailProductSimple& web_doc_id=SC0000673040&doc_type=123-2 External interference 2G: The LMT is delivered with the frequency scanning function. 3G: In R1AN2.0, the python script is used to collect frequency information for R&D analysis. In RAN13.0, the LMT is delivered with the frequency scanning function. Antenna feeder connections 2G: Make a decision based on the main/diversity level difference and uplink/downlink balance class. 3G: Make a decision based on the RTWP difference and correlation. The RTWP analysis tool is as follows: (In the tool, select check Antenna cross. The tool is continuously improved. For details, contact Zhang Junjie (employee ID: 00107307).
Huawei Confidential
Page 51
Confirming External Interference Preparing the Interference Map Using the Mapinfo
Huawei Confidential
Page 52
Network Planning Checking

Neighboring cell interference
If a neighboring cell is missing in the configuration, a few of UEs under the missing neighboring cell cannot be switched over to the local cell even when the UEs are far away from the neighboring cell and enters the coverage area of the local cell. With the increase of path loss between the UEs and the missing neighboring cell, the RX power rises. The coupling loss between the UEs and the cabinet top ports of the local cell decreases gradually. In this case, the local cell is interfered with and the RTWP of the cell rises. When the path loss between the UEs and the local cell is greater than that between the UEs and the serving cell by about 10 dB, call loss occurs. Therefore, the interference margin cannot be greater than 10 dB. Currently, the NPMaster tool is used to analyze the PCHR and RNC configuration file and the table of missing neighboring cells can be generated.
Strong coverage
Due to strong coverage of a cell, the mean coupling loss between a NodeB and UEs is small. When a few of UEs approach the antenna, the uplink power control has reached the minimum. As a result, the RTWP rises greatly.
Huawei Confidential
Checking Traffic Capacity Counters

Traffic capacity The abnormal RTWP rise is directly caused after the user uplink load increases. For example, when the uplink load reaches the capacity threshold of a cell, the RTWP rises to the maximum. If the admission control algorithm is disabled, the RTWP stays high continuously in the high traffic cell due to severe capacity overloading. The service volume fluctuates with time. Therefore, the RTWP peaks vary according to time with moderate change margin. The change trend of RTWP is consistent with that of service volume.
Traffic evaluation tool
Huawei Confidential
Service Capacity Improvement Measures
Huawei Confidential
Attachment 1 Collecting RTWP Routine Tracing Logs

1. M2000 batch processing script-based sampling
Advantages: Fast, batch processing
2. M2000 single-site sampling

Advantages: easy to operate for some sites
Huawei Confidential
Page 56
Thank you
www.huawei.com

RTWP Troubleshooting

Uploaded by

Copyright:

Available Formats

RTWP Troubleshooting

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RTWP Troubleshooting

Uploaded by

Copyright:

Available Formats

Security Level:

RTWP Troubleshooting Guide

HUAWEI TECHNOLOGIES CO., LTD.

Overview Troubleshooting Methods

Appendix 1: Method of Collecting Tracing Logs Routinely

HUAWEI TECHNOLOGIES CO., LTD.

PN = KTB + NF, where, K = Boltzmann constant, T = 290 K (room temperature)

HUAWEI TECHNOLOGIES CO., LTD.

MRFU receiver architecture

RTWP=P_in= P_out - Gain

HUAWEI TECHNOLOGIES CO., LTD.

What Does the RTWP Represents?

HUAWEI TECHNOLOGIES CO., LTD.

Controlling the RTWP on the Network Side

Overview Troubleshooting Methods

Appendix 1: Method of Collecting Tracing Logs Routinely

HUAWEI TECHNOLOGIES CO., LTD.

RTWP Sampling Points

HUAWEI TECHNOLOGIES CO., LTD.

RTWP Sampling Mode

RNC traffic statistics

HUAWEI TECHNOLOGIES CO., LTD.

Overview Troubleshooting Methods

Appendix 1: Method of Collecting Tracing Logs Routinely

HUAWEI TECHNOLOGIES CO., LTD.

Criteria for Determining an RTWP Problem

HUAWEI TECHNOLOGIES CO., LTD.

Common RTWP Problems and Troubleshooting Procedure

RTWP Troubleshooting Procedure

HUAWEI TECHNOLOGIES CO., LTD.

Method 1: Background Noise Rise when No User Is Connected

Background Noise Rise when No User Is Connected

HUAWEI TECHNOLOGIES CO., LTD.

Incorrect antenna feeder connections

HUAWEI TECHNOLOGIES CO., LTD.

HUAWEI TECHNOLOGIES CO., LTD.

HUAWEI TECHNOLOGIES CO., LTD.

Neighboring cell interference

Limited number of users

HUAWEI TECHNOLOGIES CO., LTD.

Overview Troubleshooting Methods

Appendix 1: Method of Collecting Tracing Logs Routinely

HUAWEI TECHNOLOGIES CO., LTD.

Symptoms of Main and Diversity RTWP Problems

HUAWEI TECHNOLOGIES CO., LTD.

Large Difference Between the Main RTWP and Diversity RTWP

HUAWEI TECHNOLOGIES CO., LTD.

Symptom 1: Main RTWP trend is the same as diversity

HUAWEI TECHNOLOGIES CO., LTD.

HUAWEI TECHNOLOGIES CO., LTD.

HUAWEI TECHNOLOGIES CO., LTD.

Symptom 2: Main and diversity receivers have signals,

HUAWEI TECHNOLOGIES CO., LTD.

Symptom 2: Main and diversity receivers have

HUAWEI TECHNOLOGIES CO., LTD.

Case 2: Cross Connections

Case 3: External Interference

HUAWEI TECHNOLOGIES CO., LTD.

HUAWEI TECHNOLOGIES CO., LTD.

Symptom 3The main or diversity receiver does