Professional Documents
Culture Documents
Ratioed Logic: R Resistive Load V 0 Depletion Load V 0 Pmos Load
Ratioed Logic: R Resistive Load V 0 Depletion Load V 0 Pmos Load
R
L
---------------------------- =
4
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Current source
Ideal in the sense that the available current is independent of the output voltage.
It is easy to prove that t
pLH
is reduced by 25% over the resistor load.
Depletion load
The depletion load gate shown previously emerged as the most popular gate in the
NMOS era (up until the early 80s).
The load is an NMOS depletion mode transistor (negative threshold device) with the
gate connected to the output (source).
Note that the device is on when V
GS
= 0.
The load acts as a current source (first-order), given by its saturation equation:
I
L
k
n load ,
2
-----------------
V
Tn
( )
2
=
5
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Depletion load (cont.)
The load line deviates from the ideal current source for two reasons:
(a) The channel length modulation factor modulates current in saturation mode.
(b) The source of the load transistor is connected to the output of the inverter.
The body effect causes the threshold of the load transistor to vary as a function of
V
out
.
The body effect reduces |V
Tn
| and the available current for increasing values of
V
out
.
Nevertheless, the depletion load out-performs the resistive load and requires less area!
6
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Pseudo-NMOS
A grounded PMOS device presents an even better load.
It is better than depletion NMOS because there is no body effect (its V
SB
is constant
and equal to 0).
Also, the PMOS device is driven by a V
GS
= -V
DD
, resulting in a higher load-current
level than a similarly sized depletion-NMOS device.
(ignoring channel length modulation)
The V
OH
(=V
DD
) from the dc transfer characteristic is the same as that for the full
complementary device.
V
OL
differs from GND, however.
I
L
k
p
2
-----
V
DD
V
Tp
( )
2
=
7
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Pseudo-NMOS (cont)
V
OL
can be obtained by equating the currents through the driver and load devices for
V
in
= V
DD
.
Here, the NMOS driver resides in linear mode while the PMOS load is in saturation:
Assuming V
Tn
= |V
Tp
|, solving for V
OL
yields:
For example, if k
p
= k
n
, V
OL
= V
DD
- V
T
, which is clearly unacceptable.
For r = k
p
/k
n
= 1/4, V
OL
= (5 - 0.8)*0.134 ~= 0.56V.
k
n
V
DD
V
Tn
( )V
OL
V
OL
2
2
----------
k
p
2
-----
V
DD
V
Tp
( )
2
=
V
OL
V
DD
V
T
( ) 1 1
k
p
k
n
-----
=
8
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Pseudo-NMOS (cont)
Similarly, V
M
can be computed by setting V
in
= V
out
and solving the current equations
This assumes the NMOS and PMOS are in saturation and linear, respectively.
Design challenges:
This clearly indicates that V
M
is not located in the middle of the voltage swing (e.g.
if they are equal, the square root yields 0.707).
The rise and fall times are asymmetrical.
This gate consumes static power when the output is low.
V
M
V
T
V
DD
V
T
( )
k
p
k
n
k
p
+
----------------- + =
P
av
V
DD
I
low
k
p
2
-----
V
DD
V
DD
V
T
( )
2
= =
9
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Pseudo-NMOS (cont)
Let's assume the load can be approximated as a current source for the entire operation
region.
Trade-offs:
To reduce static power, I
L
should be low.
To obtain a reasonable NM
L
, V
OL
= I
L
R
PDN
should be low.
To reduce t
pLH
~= (C
L
V
DD
)/(2I
L
), I
L
should be high.
To reduce t
pHL
~= 0.69R
PDN
C
L
, R
PDN
should be kept small.
R
PDN
In
I
L
Out
10
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Pseudo-NMOS (cont)
The r = (W/L)
n
/(W/L)
p
in the expression for V
OL
defines NM
L
.
For example, to obtain a V
OL
of 0.2V (1.2 um tech., V
DD
=5V) requires a ratio of r=3.
This also guarantees the 4th condition.
However, 1 and 3 are contradictory: realizing a faster gate (t
pLH
) means more static
power consumption and reduced noise margin.
Pseudo-NMOS attractive for complex gates with large fan-in.
A minimum sized gate consumes 1mW !
Out
A B C D
As mentioned, only N+1 transistors,
smaller area and smaller parasitics.
Smaller downstream load capacitance.
However, static power consumption
makes it impossible to use in large
circuits (except in address decoders
when majority of outputs are high).
11
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Even better loads
Consider the following modification to the pseudo-NMOS NOR.
Here, it is known that the inputs switch only during certain time periods.
For example, an address decoder which should only switch when the address
changes.
In stand-by mode, low power consumption and large noise margins.
For address change, high power fast t
pLH
transition.
Out
A B C D
Enable
12
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Even better loads (cont)
It's possible to completely eliminate static current:
Differential Cascade Voltage Switch Logic (DCVSL).
PDN
1
and PDN
2
are complementary.
Assume PDN
1
conducts, input to M
2
is turned on, pulling up Out.
This in turn, shuts off M
1
.
Speed advantage of pseudo-NMOS (reduced output parasitics) with no static power
consumption, but occupies extra area.
A
A
B
B
PDN
1
PDN
2
Out Out
M
1
M
2
Assumes signal and
its complement are
available
13
Advanced VLSI Design CMPE 640
Combinational Logic Design
Ratioed Logic
Even better loads (cont)
However, transistors can be shared between PDN
1
and PDN
2
.
This gate has been used to implement fast error-correcting logic in memories.
Plus, the availability of complementary signals eliminate extra inverter stages.
A
XOR XNOR
M
1
M
2
A
B B B B