Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
398 views

Pipe&Shell Design Tool 600KL

This document provides a finite element analysis and calculations for a 600,000 liter base oil storage tank according to ASME code standards. It details the tank dimensions, material properties, and calculations for required thickness, maximum internal pressure, volume, and weight. The analysis determines that the minimum required thickness of 0.201 inches is less than the nominal wall thickness of 0.403 inches, and the maximum allowed internal pressure of 29 psi is greater than the design pressure of 14.5 psi.

Uploaded by

Joshua Rivera
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
398 views

Pipe&Shell Design Tool 600KL

This document provides a finite element analysis and calculations for a 600,000 liter base oil storage tank according to ASME code standards. It details the tank dimensions, material properties, and calculations for required thickness, maximum internal pressure, volume, and weight. The analysis determines that the minimum required thickness of 0.201 inches is less than the nominal wall thickness of 0.403 inches, and the maximum allowed internal pressure of 29 psi is greater than the design pressure of 14.5 psi.

Uploaded by

Joshua Rivera
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

1

Pressure Vessel Engineering Ltd.

Finite Element Analysis ASME Code Calculations


Canadian Vessel Registration Vessel Modeling and Drafting

3
4
5
6

Pipe and Shell Design Tool ver E4.02

Shell 1-2 Base Oil Storage Tank Group 2 600KL Description

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

43
44
45
46

Dimensions:
377.952
0.472
360.000
0.010

Do [in] - outside diameter


t [in] - nominal wall thickness
L [in] -length
Corr [in] - corrosion allowance

Material and Conditions:


SS400 Material
16,000 S [psi] - allowable stress
0.85
0.70
12.5%
14.5

El - long seam efficiency (circ stress)


Ec - circ seam efficiency (long stress)
UTP [%] - undertolerance allowance
P [psi] - interior pressure

Calculated Properties:
Volume [cuft] = ((Do/2-t)^2)*pi()*L/1728
Weight [lb] = (Do-t)*pi()*L*t*40.84/144

Long Seam

Page 1 of 1

((377.952/2-0.472)^2)*PI()*360/1728 = 23256.79
(377.952-0.472)*PI()*360*0.472*40.84/144 = 57149.38

Variables:
UT [in] = t*UTP
nt [in] = t-Corr-UT
Ri [in] = Do/2-nt

0.472*0.1 = 0.059
0.472-0.01-0.059 = 0.403
377.952/2-0.403 = 188.573

Required Thickness: UG-27(c)(1,2)


ta [in] = P*Ri/(S*El-0.6*P) ~~ long sem
14.5*188.573/(16000*0.85-0.6*14.5) =
tb [in] = P*Ri/(2*S*Ec+0.4*P) ~~ circ seam 14.5*188.573/(2*16000*0.7+0.4*14.5) =
Treq [in] = MAX(ta,tb) ~~ required minimum thickness
MAX(0.201,0.122) =
CheckTreq = Treq <= nt
0.201 <= 0.403 =

0.201
0.122
0.201
Acceptable

Maximum Pressure: UG-27(c)(1,2)


Pint1 [psi] = (S*El*nt)/(Ri+0.6*nt)
(16000*0.85*0.403)/(188.573+0.6*0.403) =
Pint2 [psi] = (2*S*Ec*nt)/(Ri-0.4*nt)
(2*16000*0.7*0.403)/(188.573-0.4*0.403) =
PMax [psi] = Min(Pint1,Pint2) ~~ maximum allowed design pressure
MIN(29,48) =
CheckP = PMax >= P
29 >= 14.5 =

29
48
29.0
Acceptable

Treq provides a worst case required thickness for nozzle analysis for a nozzle located on the long seam or circ seam
This sheet will not calculate thick walled vessels
Check Not a thick walled vessel, calculations are valid
The UG-16(b) minimum thickness requirement has not been taken into consideration here.
This sheet cannot be used to check for allowable exterior pressure loads.
Use the Weld Efficiency program to calculate El and Ec
This sheet is for educational use only - use at your own risk.

Pressure Vessel Engineering Ltd.


120 Randall Drive, Suite B
Waterloo, Ontario, Canada, N2V 1C6
www.pveng.com (519) 880-9808

You might also like