Heat and Mass Transfer: Fundamentals & Applications

Fourth Edition
Yunus A. Cengel, Afshin J. Ghajar
McGraw-Hill, 2011

Chapter 2
HEAT CONDUCTION
EQUATION
Mehmet Kanoglu
University of Gaziantep
Copyright 2011 The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

Objectives

Understand multidimensionality and time dependence of heat transfer,

and the conditions under which a heat transfer problem can be
approximated as being one-dimensional.

Obtain the differential equation of heat conduction in various

coordinate systems, and simplify it for steady one-dimensional case.

Identify the thermal conditions on surfaces, and express them

mathematically as boundary and initial conditions.

Solve one-dimensional heat conduction problems and obtain the

temperature distributions within a medium and the heat flux.

Analyze one-dimensional heat conduction in solids that involve heat

generation.

Evaluate heat conduction in solids with temperature-dependent

thermal conductivity.
2

INTRODUCTION

Although heat transfer and temperature are closely related, they are of a
different nature.
Temperature has only magnitude. It is a scalar quantity.
Heat transfer has direction as well as magnitude. It is a vector quantity.
We work with a coordinate system and indicate direction with plus or minus
signs.

The driving force for any form of heat transfer is the temperature
difference.

The larger the temperature difference, the larger the rate of heat transfer.

Three prime coordinate systems:

rectangular T(x, y, z, t)
cylindrical T(r, , z, t)
spherical T(r, , , t).

Steady versus Transient Heat Transfer

Steady implies no change

with time at any point within
the medium

Transient implies variation

with time or time
dependence

In the special case of

variation with time but not
with position, the
temperature of the medium
changes uniformly with
time. Such heat transfer
systems are called lumped
systems.

Multidimensional Heat Transfer

Heat transfer problems are also classified as being:

one-dimensional
two dimensional
three-dimensional

In the most general case, heat transfer through a medium is threedimensional. However, some problems can be classified as two- or
one-dimensional depending on the relative magnitudes of heat
transfer rates in different directions and the level of accuracy desired.

One-dimensional if the temperature in the medium varies in one

direction only and thus heat is transferred in one direction, and the
variation of temperature and thus heat transfer in other directions are
negligible or zero.

Two-dimensional if the temperature in a medium, in some cases,

varies mainly in two primary directions, and the variation of
temperature in the third direction (and thus heat transfer in that
direction) is negligible.
6

 The rate of heat conduction through a medium in a specified direction (say, in the x-direction)
is expressed by Fouriers law of heat conduction for one-dimensional heat conduction as:

Heat is conducted in the direction

of decreasing temperature, and
thus the temperature gradient is
negative when heat is conducted
in the positive x -direction.

 The heat flux vector at a point P on the

surface of the figure must be
perpendicular to the surface, and it
must point in the direction of
decreasing temperature
If n is the normal of the isothermal
surface at point P, the rate of heat
conduction at that point can be
expressed by Fouriers law as

Examples:
electrical energy being converted to heat at a rate of I2R,
fuel elements of nuclear reactors,
exothermic chemical reactions.
Heat generation is a volumetric phenomenon.
The rate of heat generation units : W/m3 or Btu/hft3.
The rate of heat generation in a medium may vary with time as well as
position within the medium.

Heat
Generation

10

ONE-DIMENSIONAL HEAT CONDUCTION

EQUATION
Consider heat conduction through a large plane wall such as the wall of a
house, the glass of a single pane window, the metal plate at the bottom of
a pressing iron, a cast-iron steam pipe, a cylindrical nuclear fuel element,
an electrical resistance wire, the wall of a spherical container, or a
spherical metal ball that is being quenched or tempered.
Heat conduction in these and many other geometries can be
approximated as being one-dimensional since heat conduction through
these geometries is dominant in one direction and negligible in other
directions.
Next we develop the onedimensional heat conduction equation in
rectangular, cylindrical, and spherical coordinates.

11

Heat Conduction
Equation in a Large
Plane Wall
(2-6)

12

13

Heat
Conduction
Equation in a
Long Cylinder

14

15

Heat Conduction Equation

in a Sphere

16

Combined One-Dimensional Heat Conduction

Equation
An examination of the one-dimensional transient heat conduction
equations for the plane wall, cylinder, and sphere reveals that all
three equations can be expressed in a compact form as

n = 0 for a plane wall

n = 1 for a cylinder
n = 2 for a sphere
In the case of a plane wall, it is customary to replace the variable
r by x.
This equation can be simplified for steady-state or no heat
generation cases as described before.
17

GENERAL HEAT CONDUCTION EQUATION

In the last section we considered one-dimensional heat conduction
and assumed heat conduction in other directions to be negligible.
Most heat transfer problems encountered in practice can be
approximated as being one-dimensional, and we mostly deal with
such problems in this text.
However, this is not always the case, and sometimes we need to
consider heat transfer in other directions as well.
In such cases heat conduction is said to be multidimensional, and
in this section we develop the governing differential equation in
such systems in rectangular, cylindrical, and spherical coordinate
systems.

18

Rectangular Coordinates

19

20

21

Cylindrical Coordinates
Relations between the coordinates of a point in rectangular
and cylindrical coordinate systems:

22

Spherical Coordinates
Relations between the coordinates of a point in rectangular
and spherical coordinate systems:

23

BOUNDARY AND INITIAL CONDITIONS

The description of a heat transfer problem in a medium is not complete without a full
description of the thermal conditions at the bounding surfaces of the medium.

Boundary conditions: The mathematical expressions of the thermal conditions at the

boundaries.

The temperature at any

point on the wall at a
specified time depends
on the condition of the
geometry at the
beginning of the heat
conduction process.
Such a condition, which
is usually specified at
time t = 0, is called the
initial condition, which
is a mathematical
expression for the
temperature distribution
of the medium initially.
24

Boundary Conditions
Specified Temperature Boundary Condition
Specified Heat Flux Boundary Condition
Convection Boundary Condition
Radiation Boundary Condition
Interface Boundary Conditions
Generalized Boundary Conditions

25

1 Specified Temperature Boundary Condition

The temperature of an exposed surface
can usually be measured directly and
easily.
Therefore, one of the easiest ways to
specify the thermal conditions on a surface
is to specify the temperature.
For one-dimensional heat transfer through
a plane wall of thickness L, for example,
the specified temperature boundary
conditions can be expressed as

where T1 and T2 are the specified

temperatures at surfaces at x = 0 and
x = L, respectively.
The specified temperatures can be
constant, which is the case for steady
heat conduction, or may vary with time.

26

2 Specified Heat Flux Boundary Condition

The heat flux in the positive x-direction anywhere in the
medium, including the boundaries, can be expressed by

For a plate of thickness L subjected to heat

flux of 50 W/m2 into the medium from both
sides, for example, the specified heat flux
boundary conditions can be expressed as

27

Special Case: Insulated Boundary

A well-insulated surface can be modeled
as a surface with a specified heat flux of
zero. Then the boundary condition on a
perfectly insulated surface (at x = 0, for
example) can be expressed as

On an insulated surface, the first

derivative of temperature with respect
to the space variable (the temperature
gradient) in the direction normal to the
insulated surface is zero.

28

Another Special Case: Thermal Symmetry

Some heat transfer problems possess thermal
symmetry as a result of the symmetry in imposed
thermal conditions.
For example, the two surfaces of a large hot plate
of thickness L suspended vertically in air is
subjected to the same thermal conditions, and thus
the temperature distribution in one half of the plate
is the same as that in the other half.
That is, the heat transfer problem in this plate
possesses thermal symmetry about the center
plane at x = L/2.
Therefore, the center plane can be viewed as an
insulated surface, and the thermal condition at this
plane of symmetry can be expressed as

which resembles the insulation or zero heat

flux boundary condition.

29

3 Convection Boundary Condition

For one-dimensional heat transfer in the x-direction
in a plate of thickness L, the convection boundary
conditions on both surfaces:

30

4 Radiation Boundary Condition

Radiation boundary condition on a surface:

For one-dimensional heat transfer in the

x-direction in a plate of thickness L, the
radiation boundary conditions on both
surfaces can be expressed as

31

5 Interface Boundary Conditions

The boundary conditions at an interface
are based on the requirements that
(1) two bodies in contact must have the
same temperature at the area of contact
and
(2) an interface (which is a surface) cannot
store any energy, and thus the heat flux on
the two sides of an interface must be the
same.
The boundary conditions at the interface
of two bodies A and B in perfect contact at
x = x0 can be expressed as

32

6 Generalized Boundary Conditions

In general, however, a surface may involve convection,
radiation, and specified heat flux simultaneously.
The boundary condition in such cases is again obtained
from a surface energy balance, expressed as

33

SOLUTION OF STEADY ONE-DIMENSIONAL

HEAT CONDUCTION PROBLEMS
In this section we will solve a wide range of heat
conduction problems in rectangular, cylindrical,
and spherical geometries.
We will limit our attention to problems that result
in ordinary differential equations such as the
steady one-dimensional heat conduction
problems. We will also assume constant thermal
conductivity.
The solution procedure for solving heat
conduction problems can be summarized as
(1) formulate the problem by obtaining the
applicable differential equation in its simplest
form and specifying the boundary conditions,
(2) Obtain the general solution of the differential
equation, and
(3) apply the boundary conditions and determine
the arbitrary constants in the general solution.

34

35

36

37

38

39

40

41

42

HEAT GENERATION IN A SOLID

Many practical heat transfer applications
involve the conversion of some form of energy
into thermal energy in the medium.
Such mediums are said to involve internal heat
generation, which manifests itself as a rise in
temperature throughout the medium.
Some examples of heat generation are
- resistance heating in wires,
- exothermic chemical reactions in a solid, and
- nuclear reactions in nuclear fuel rods
where electrical, chemical, and nuclear
energies are converted to heat, respectively.
Heat generation in an electrical wire of outer
radius ro and length L can be expressed as

43

The quantities of major interest in a medium with

heat generation are the surface temperature Ts
and the maximum temperature Tmax that occurs in
the medium in steady operation.

44

45

VARIABLE THERMAL CONDUCTIVITY, k(T)

When the variation of thermal conductivity with
temperature in a specified temperature interval is
large, it may be necessary to account for this
variation to minimize the error.
When the variation of thermal conductivity with
temperature k(T) is known, the average value of
the thermal conductivity in the temperature range
between T1 and T2 can be determined from

46

The variation in thermal conductivity of a material with

temperature in the temperature range of interest can often be
approximated as a linear function and expressed as

temperature coefficient
of thermal conductivity.
The average value of thermal conductivity
in the temperature range T1 to T2 in this
case can be determined from

The average thermal conductivity in this

case is equal to the thermal conductivity
value at the average temperature.
47

Summary
Introduction
Steady versus Transient Heat Transfer
Multidimensional Heat Transfer
Heat Generation

One-Dimensional Heat Conduction Equation

Heat Conduction Equation in a Large Plane Wall

Heat Conduction Equation in a Long Cylinder
Heat Conduction Equation in a Sphere
Combined One-Dimensional Heat Conduction Equation

General Heat Conduction Equation

Rectangular Coordinates
Cylindrical Coordinates
Spherical Coordinates

Boundary and Initial Conditions

Solution of Steady One-Dimensional Heat Conduction Problems
Heat Generation in a Solid
Variable Thermal Conductivity k (T )

48