0% found this document useful (0 votes)

86 views

EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures

This document summarizes the verification of steel column sections according to Eurocode 3. It analyzes 4 column sections - IPE 360, IPE 360, IPE 140, and IPE 330 - subject to various load cases. For each section, it provides the material properties, section parameters, internal forces and capacities, buckling parameters, and verifies that the section satisfies all verification formulas for strength and displacements. All sections were found to be verified according to Eurocode 3.

Uploaded by

Joshue Adele

Available Formats

Download as DOCX, PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

86 views

EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures

Uploaded by

Joshue Adele

Available Formats

Download as DOCX, PDF, TXT or read online on Scribd

You are on page 1/ 52

STEEL DESIGN

---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.

ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 1 Column_1
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 360
h=360 mm
gM0=1.00
gM1=1.00
b=170 mm
Ay=4884 mm2
Az=3514 mm2
Ax=7273 mm2
tw=8 mm
Iy=162656000 mm4
Iz=10434500 mm4
Ix=362000 mm4
tf=13 mm
Wply=1019220 mm3
Wplz=191104 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -69.54 kN
My,Ed = -0.97 kN*m
Mz,Ed = 5.26 kN*m
Vy,Ed = -16.57 kN
Nt,Rd = 2000.05 kN
My,pl,Rd = 280.29 kN*m Mz,pl,Rd = 52.55 kN*m
Vy,T,Rd = 345.60 kN
My,c,Rd = 280.29 kN*m Mz,c,Rd = 52.55 kN*m
Vz,Ed = 1.86 kN
MN,y,Rd = 280.29 kN*m MN,z,Rd = 52.55 kN*m
Vz,T,Rd = 392.58 kN
Tt,Ed = 4.53 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.03 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.10 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.05 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 1.00 > 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.63 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 1 mm < vx max = L/150.00 = 27 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 0 mm < vy max = L/150.00 = 27 mm
Verified
Governing Load Case: 7 WL2 - 180
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 2 Column_2
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 360
h=360 mm
gM0=1.00
gM1=1.00
b=170 mm
Ay=4884 mm2
Az=3514 mm2
Ax=7273 mm2
tw=8 mm
Iy=162656000 mm4
Iz=10434500 mm4
Ix=362000 mm4
tf=13 mm
Wply=1019220 mm3
Wplz=191104 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -54.40 kN
My,Ed = 0.98 kN*m
Mz,Ed = -0.56 kN*m
Vy,Ed = -18.73 kN
Nt,Rd = 2000.05 kN
My,pl,Rd = 280.29 kN*m Mz,pl,Rd = 52.55 kN*m
Vy,T,Rd = 354.50 kN
My,c,Rd = 280.29 kN*m Mz,c,Rd = 52.55 kN*m
Vz,Ed = -1.84 kN
MN,y,Rd = 280.29 kN*m MN,z,Rd = 52.55 kN*m
Vz,T,Rd = 395.16 kN
Tt,Ed = -4.47 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.03 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.01 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.05 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.99 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.62 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 1 mm < vx max = L/150.00 = 27 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 0 mm < vy max = L/150.00 = 27 mm
Verified
Governing Load Case: 7 WL2 - 180
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 2

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 3 Column_3
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -130.91 kN
My,Ed = 1.10 kN*m
Mz,Ed = 0.27 kN*m
Vy,Ed = 0.22 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 177.05 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = -0.61 kN
MN,y,Rd = 21.39 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.33 kN
Tt,Ed = -0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.29 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.45 = 0.02 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 3 mm < vx max = L/150.00 = 17 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 2 mm < vy max = L/150.00 = 17 mm
Verified
Governing Load Case: 8 WL2 - 180 roof
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 3

Date : 05/08/15

Page : 4

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 4 Column_4
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 12 COMB4 (1+3+2)*1.35+(4+7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 330
h=330 mm
gM0=1.00
gM1=1.00
b=160 mm
Ay=4228 mm2
Az=3081 mm2
Ax=6261 mm2
tw=8 mm
Iy=117669000 mm4
Iz=7881430 mm4
Ix=257000 mm4
tf=12 mm
Wply=804399 mm3
Wplz=153683 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -29.98 kN
My,Ed = 0.06 kN*m
Mz,Ed = -14.12 kN*m
Vy,Ed = -18.37 kN
Nt,Rd = 1721.67 kN
My,pl,Rd = 221.21 kN*m Mz,pl,Rd = 42.26 kN*m
Vy,T,Rd = 450.31 kN
My,c,Rd = 221.21 kN*m Mz,c,Rd = 42.26 kN*m
Vz,Ed = -1.54 kN
MN,y,Rd = 221.21 kN*m MN,z,Rd = 42.26 kN*m
Vz,T,Rd = 391.72 kN
Tt,Ed = 2.44 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.02 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.33 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.04 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.69 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.45 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 0 mm < vx max = L/150.00 = 21 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 0 mm < vy max = L/150.00 = 21 mm
Verified
Governing Load Case: 7 WL2 - 180
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 5

Date : 05/08/15

Page : 6

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 5 Column_5
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 330
h=330 mm
gM0=1.00
gM1=1.00
b=160 mm
Ay=4228 mm2
Az=3081 mm2
Ax=6261 mm2
tw=8 mm
Iy=117669000 mm4
Iz=7881430 mm4
Ix=257000 mm4
tf=12 mm
Wply=804399 mm3
Wplz=153683 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -15.70 kN
My,Ed = 0.13 kN*m
Mz,Ed = -8.52 kN*m
Vy,Ed = -15.76 kN
Nt,Rd = 1721.67 kN
My,pl,Rd = 221.21 kN*m Mz,pl,Rd = 42.26 kN*m
Vy,T,Rd = 437.78 kN
My,c,Rd = 221.21 kN*m Mz,c,Rd = 42.26 kN*m
Vz,Ed = 1.81 kN
MN,y,Rd = 221.21 kN*m MN,z,Rd = 42.26 kN*m
Vz,T,Rd = 386.77 kN
Tt,Ed = -2.55 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.01 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.20 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.04 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.72 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.47 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 0 mm < vx max = L/150.00 = 21 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 0 mm < vy max = L/150.00 = 21 mm
Verified
Governing Load Case: 7 WL2 - 180
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 7

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 13

Nt,Rd = 676.50 kN

My,el,Rd = 6.94 kN*m

My,c,Rd = 6.94 kN*m

Mz,el,Rd = 10.44 kN*m

Mz,c,Rd = 10.44 kN*m

Vy,T,Rd = 203.23 kN
Vz,Ed = -0.49 kN
Vz,T,Rd = 182.90 kN
Tt,Ed = -0.00 kN*m
Class of section = 3
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.15 < 1.00 (6.2.9.3.(1))
sqrt(Sig,x,Ed*^2 + 3*Tau,z,Ed^2)/(fy/gM0) = 0.18 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,c,Rd = 0.00 < 1.00 (6.2.6.(1))
Vz,Ed/Vz,c,Rd = 0.00 < 1.00 (6.2.6.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 3 mm < uy max = L/200.00 = 36 mm
Governing Load Case: 5 WL1 - 90
uz = 1 mm < uz max = L/200.00 = 36 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 14

My,c,Rd = 6.94 kN*m

Mz,c,Rd = 10.44 kN*m

Vz,Ed = 0.50 kN
Vz,T,Rd = 182.90 kN
Tt,Ed = -0.00 kN*m
Class of section = 3
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.75 < 1.00 (6.2.9.3.(1))
sqrt(Sig,x,Ed*^2 + 3*Tau,z,Ed^2)/(fy/gM0) = 0.78 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,c,Rd = 0.03 < 1.00 (6.2.6.(1))
Vz,Ed/Vz,c,Rd = 0.00 < 1.00 (6.2.6.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 14 mm < uy max = L/200.00 = 36 mm
Governing Load Case: 5 WL1 - 90
uz = 1 mm < uz max = L/200.00 = 36 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 18 Beam_18
POINT: 1
COORDINATE: x = 0.54 L = 3.90 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 330
h=330 mm
gM0=1.00
gM1=1.00
b=160 mm
Ay=4228 mm2
Az=3081 mm2
Ax=6261 mm2
tw=8 mm
Iy=117669000 mm4
Iz=7881430 mm4
Ix=257000 mm4
tf=12 mm
Wply=804399 mm3
Wplz=153683 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = 16.36 kN
My,Ed = 55.35 kN*m
Mz,Ed = -5.17 kN*m
Vy,Ed = -8.22 kN
Nc,Rd = 1721.67 kN
My,pl,Rd = 221.21 kN*m Mz,pl,Rd = 42.26 kN*m
Vy,T,Rd = 671.21 kN
Nb,Rd = 1721.67 kN
My,c,Rd = 221.21 kN*m Mz,c,Rd = 42.26 kN*m
Vz,Ed = -64.01 kN

Date : 05/08/15

Page : 15

MN,y,Rd = 221.21 kN*m

Mb,Rd = 75.16 kN*m

MN,z,Rd = 42.26 kN*m

Vz,T,Rd = 489.11 kN
Tt,Ed = 0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 82.06 kN*m
Curve,LT - c
XLT = 0.34
Lcr,upp=7.20 m
Lam_LT = 1.64
fi,LT = 1.82
XLT,mod = 0.34
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:
kyy = 1.00
kzz = 1.00
---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd = 0.01 < 1.00 (6.2.4.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.18 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.01 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.13 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.74 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.87 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.87 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 2 mm < uy max = L/200.00 = 36 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 4 mm < uz max = L/200.00 = 36 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

gM1=1.00
Az=3081 mm2

Page : 16

Ax=6261 mm2

tw=8 mm
Iy=117669000 mm4
Iz=7881430 mm4
Ix=257000 mm4
tf=12 mm
Wply=804399 mm3
Wplz=153683 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = 18.05 kN
My,Ed = 59.09 kN*m
Mz,Ed = -6.89 kN*m
Vy,Ed = 8.70 kN
Nc,Rd = 1721.67 kN
My,pl,Rd = 221.21 kN*m Mz,pl,Rd = 42.26 kN*m
Vy,T,Rd = 669.49 kN
Nb,Rd = 1721.67 kN
My,c,Rd = 221.21 kN*m Mz,c,Rd = 42.26 kN*m
Vz,Ed = 65.02 kN
MN,y,Rd = 221.21 kN*m MN,z,Rd = 42.26 kN*m
Vz,T,Rd = 488.29 kN
Mb,Rd = 75.16 kN*m
Tt,Ed = -0.02 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 82.06 kN*m
Curve,LT - c
XLT = 0.34
Lcr,upp=7.20 m
Lam_LT = 1.64
fi,LT = 1.82
XLT,mod = 0.34
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:
kyy = 1.00
kzz = 1.00
---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd = 0.01 < 1.00 (6.2.4.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.23 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.01 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.13 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.01 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.79 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.96 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.96 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 3 mm < uy max = L/200.00 = 36 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 3 mm < uz max = L/200.00 = 36 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 17

S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -9.86 kN
My,Ed = -9.96 kN*m
Mz,Ed = -0.07 kN*m
Vy,Ed = -0.17 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 177.01 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 17.58 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.31 kN
Mb,Rd = 22.63 kN*m
Tt,Ed = -0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 62.06 kN*m
Curve,LT - b
XLT = 0.91
Lcr,low=0.95 m
Lam_LT = 0.63
fi,LT = 0.69
XLT,mod = 0.93
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.02 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.18 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.14 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.44 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 18

---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -1.29 kN
My,Ed = -1.06 kN*m
Mz,Ed = -0.27 kN*m
Vy,Ed = -0.58 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 176.91 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 2.51 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.26 kN
Mb,Rd = 23.43 kN*m
Tt,Ed = -0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 80.14 kN*m
Curve,LT - b
XLT = 0.94
Lcr,upp=0.81 m
Lam_LT = 0.55
fi,LT = 0.64
XLT,mod = 0.96
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.00 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.05 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.02 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.05 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 4 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 4 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

STEEL DESIGN
----------------------------------------------------------------------------------------------------------------------------------------

Date : 05/08/15

Page : 19

CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.

ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 25 Beam_25
POINT: 3
COORDINATE: x = 1.00 L = 0.99 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = 0.20 kN
My,Ed = 0.20 kN*m
Mz,Ed = 0.29 kN*m
Vy,Ed = -0.59 kN
Nc,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 176.88 kN
Nb,Rd = 451.71 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 0.09 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.25 kN
Mb,Rd = 22.39 kN*m
Tt,Ed = -0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 57.91 kN*m
Curve,LT - b
XLT = 0.90
Lcr,upp=0.99 m
Lam_LT = 0.65
fi,LT = 0.70
XLT,mod = 0.92
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:
kyy = 1.00
kzz = 1.00
---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd = 0.00 < 1.00 (6.2.4.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.06 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.01 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.06 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.06 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof

Date : 05/08/15

Verified
Verified

Page : 20

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 27 Beam_27
POINT: 3
COORDINATE: x = 1.00 L = 5.80 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 12 COMB4 (1+3+2)*1.35+(4+7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -18.12 kN
My,Ed = -6.79 kN*m
Mz,Ed = 0.22 kN*m
Vy,Ed = -0.30 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 173.13 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = -7.76 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 119.51 kN
Mb,Rd = 7.65 kN*m
Tt,Ed = -0.03 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 7.65 kN*m
Curve,LT - b
XLT = 0.31
Lcr,low=5.80 m
Lam_LT = 1.78
fi,LT = 1.93
XLT,mod = 0.31
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.04 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.12 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.06 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.05 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.04 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.89 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS

Date : 05/08/15

Page : 21

Deflections
uy = 2 mm < uy max = L/200.00 = 29 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 3 mm < uz max = L/200.00 = 29 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

Section OK !!!

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 31 Beam_31
POINT: 3
COORDINATE: x = 0.33 L = 1.90 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -17.88 kN
My,Ed = 4.51 kN*m
Mz,Ed = 0.23 kN*m
Vy,Ed = -0.23 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 176.84 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 4.86 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.23 kN
Mb,Rd = 7.65 kN*m
Tt,Ed = -0.00 kN*m
Class of section = 1
----------------------------------------------------------------------------------------------------------------------------------------

Date : 05/08/15

Page : 25

LATERAL BUCKLING PARAMETERS:

z = 1.00
Mcr = 7.65 kN*m
Curve,LT - b
XLT = 0.31
Lcr,upp=5.80 m
Lam_LT = 1.78
fi,LT = 1.93
XLT,mod = 0.31
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.04 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.08 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.04 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.59 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 2 mm < uy max = L/200.00 = 29 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 2 mm < uz max = L/200.00 = 29 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 26

My,c,Rd = 24.30 kN*m

MN,y,Rd = 24.30 kN*m
Mb,Rd = 22.63 kN*m

Mz,c,Rd = 5.29 kN*m

MN,z,Rd = 5.29 kN*m

Vz,Ed = -18.53 kN
Vz,T,Rd = 121.29 kN
Tt,Ed = 0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 62.06 kN*m
Curve,LT - b
XLT = 0.91
Lcr,low=0.95 m
Lam_LT = 0.63
fi,LT = 0.69
XLT,mod = 0.93
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.02 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.20 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.15 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.48 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

gM1=1.00
Az=764 mm2
Iz=449178 mm4

Page : 27

Ax=1643 mm2
Ix=25400 mm4

About z axis:
kyy = 1.00
kzz = 1.00
---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd = 0.00 < 1.00 (6.2.4.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.01 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.02 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.08 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.08 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.08 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 4 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 4 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Date : 05/08/15

Page : 31

Section OK !!!

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 44 Beam_44
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = 2.84 kN
My,Ed = 0.61 kN*m
Mz,Ed = 0.00 kN*m
Vy,Ed = -0.00 kN
Nc,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 177.04 kN
Nb,Rd = 451.71 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = -0.47 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.32 kN
Mb,Rd = 24.30 kN*m
Tt,Ed = -0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 134.19 kN*m
Curve,LT - b
XLT = 0.99
Lcr,upp=0.60 m
Lam_LT = 0.43
fi,LT = 0.57
XLT,mod = 1.00
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:
kyy = 1.00
kzz = 1.00
---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd = 0.01 < 1.00 (6.2.4.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.00 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.03 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.03 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.03 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections

Date : 05/08/15

Page : 32

uy = 0 mm < uy max = L/200.00 = 3 mm

Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 3 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

STEEL DESIGN
---------------------------------------------------------------------------------------------------------------------------------------CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 45 Beam_45
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = 0.04 kN
My,Ed = -0.80 kN*m
Mz,Ed = -0.00 kN*m
Vy,Ed = -0.00 kN
Nc,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 176.98 kN
Nb,Rd = 451.71 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 1.23 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.30 kN
Mb,Rd = 23.04 kN*m
Tt,Ed = 0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 70.17 kN*m
Curve,LT - b
XLT = 0.92
Lcr,low=0.88 m
Lam_LT = 0.59
fi,LT = 0.66
XLT,mod = 0.95
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

Date : 05/08/15

Page : 33

My,Ed/Mb,Rd = 0.03 < 1.00 (6.3.2.1.(1))

N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.04 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.04 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 4 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 4 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 37

Nc,Rd = 451.71 kN
Nb,Rd = 451.71 kN

My,pl,Rd = 24.30 kN*m

My,c,Rd = 24.30 kN*m
MN,y,Rd = 24.30 kN*m
Mb,Rd = 22.39 kN*m

Mz,pl,Rd = 5.29 kN*m

Mz,c,Rd = 5.29 kN*m
MN,z,Rd = 5.29 kN*m

Vy,T,Rd = 170.59 kN
Vz,Ed = 0.21 kN
Vz,T,Rd = 118.33 kN
Tt,Ed = -0.05 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 57.91 kN*m
Curve,LT - b
XLT = 0.90
Lcr,upp=0.99 m
Lam_LT = 0.65
fi,LT = 0.70
XLT,mod = 0.92
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:
kyy = 1.00
kzz = 1.00
---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nc,Rd = 0.00 < 1.00 (6.2.4.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.01 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.09 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.06 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.00 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed/(XLT*My,Rk/gM1) + kyz*Mz,Ed/(Mz,Rk/gM1) = 0.01 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed/(XLT*My,Rk/gM1) + kzz*Mz,Ed/(Mz,Rk/gM1) = 0.01 < 1.00 (6.3.3.(4))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 5 mm
Governing Load Case: 3 DL2 - Empty Pipe

Verified
Verified

----------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 47

Governing Load Case: 10 COMB2 (1+3+2)1.35+(7+8)1.50

---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -119.67 kN
My,Ed = 1.12 kN*m
Mz,Ed = 0.30 kN*m
Vy,Ed = 0.23 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 177.02 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = -0.59 kN
MN,y,Rd = 22.14 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.32 kN
Tt,Ed = -0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.26 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.32 = 0.03 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.00 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 3 mm < vx max = L/150.00 = 17 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 2 mm < vy max = L/150.00 = 17 mm
Verified
Governing Load Case: 8 WL2 - 180 roof
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 48

LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -90.75 kN
My,Ed = -1.21 kN*m
Mz,Ed = 0.45 kN*m
Vy,Ed = 0.30 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 177.03 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 0.82 kN
MN,y,Rd = 24.07 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.32 kN
Tt,Ed = 0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.20 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.09 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.01 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections Not analyzed
Displacements
vx = 3 mm < vx max = L/150.00 = 17 mm
Verified
Governing Load Case: 5 WL1 - 90
vy = 1 mm < vy max = L/150.00 = 17 mm
Verified
Governing Load Case: 8 WL2 - 180 roof
----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

Date : 05/08/15

Page : 49

---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -113.96 kN
My,Ed = 6.24 kN*m
Mz,Ed = -0.01 kN*m
Vy,Ed = 0.67 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 176.86 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = -11.24 kN
MN,y,Rd = 22.52 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.24 kN
Mb,Rd = 22.63 kN*m
Tt,Ed = 0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 62.06 kN*m
Curve,LT - b
XLT = 0.91
Lcr,upp=0.95 m
Lam_LT = 0.63
fi,LT = 0.69
XLT,mod = 0.93
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.25 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.26 = 0.08 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.09 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.28 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Section OK !!!

STEEL DESIGN
----------------------------------------------------------------------------------------------------------------------------------------

Date : 05/08/15

Page : 50

CODE: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.

ANALYSIS TYPE: Member Verification
---------------------------------------------------------------------------------------------------------------------------------------CODE GROUP:
MEMBER: 68 Beam_68
POINT: 1
COORDINATE: x = 0.00 L = 0.00 m
---------------------------------------------------------------------------------------------------------------------------------------LOADS:
Governing Load Case: 10 COMB2 (1+3+2)*1.35+(7+8)*1.50
---------------------------------------------------------------------------------------------------------------------------------------MATERIAL:
S275 ( S275 )
fy = 275.00 MPa
---------------------------------------------------------------------------------------------------------------------------------------SECTION PARAMETERS: IPE 140
h=140 mm
gM0=1.00
gM1=1.00
b=73 mm
Ay=1115 mm2
Az=764 mm2
Ax=1643 mm2
tw=5 mm
Iy=5412240 mm4
Iz=449178 mm4
Ix=25400 mm4
tf=7 mm
Wply=88349 mm3
Wplz=19247 mm3
---------------------------------------------------------------------------------------------------------------------------------------INTERNAL FORCES AND CAPACITIES:
N,Ed = -82.22 kN
My,Ed = -6.97 kN*m
Mz,Ed = 0.01 kN*m
Vy,Ed = 0.62 kN
Nt,Rd = 451.71 kN
My,pl,Rd = 24.30 kN*m
Mz,pl,Rd = 5.29 kN*m
Vy,T,Rd = 177.03 kN
My,c,Rd = 24.30 kN*m
Mz,c,Rd = 5.29 kN*m
Vz,Ed = 13.09 kN
MN,y,Rd = 24.30 kN*m
MN,z,Rd = 5.29 kN*m
Vz,T,Rd = 121.32 kN
Mb,Rd = 22.63 kN*m
Tt,Ed = 0.00 kN*m
Class of section = 1
---------------------------------------------------------------------------------------------------------------------------------------LATERAL BUCKLING PARAMETERS:
z = 1.00
Mcr = 62.06 kN*m
Curve,LT - b
XLT = 0.91
Lcr,low=0.95 m
Lam_LT = 0.63
fi,LT = 0.69
XLT,mod = 0.93
---------------------------------------------------------------------------------------------------------------------------------------BUCKLING PARAMETERS:
About y axis:

About z axis:

---------------------------------------------------------------------------------------------------------------------------------------VERIFICATION FORMULAS:
Section strength check:
N,Ed/Nt,Rd = 0.18 < 1.00 (6.2.3.(1))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.00 = 0.08 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.11 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Global stability check of member:
My,Ed/Mb,Rd = 0.31 < 1.00 (6.3.2.1.(1))
---------------------------------------------------------------------------------------------------------------------------------------LIMIT DISPLACEMENTS
Deflections
uy = 0 mm < uy max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof
uz = 0 mm < uz max = L/200.00 = 5 mm
Governing Load Case: 8 WL2 - 180 roof

Verified
Verified

Displacements Not analyzed

----------------------------------------------------------------------------------------------------------------------------------------

Date : 05/08/15

Page : 51

Section OK !!!

Date : 05/08/15

Page : 52

Iso 62304 PDF
No ratings yet
Iso 62304 PDF
3 pages
Wind Load Calculation From Eurocode 1
67% (3)
Wind Load Calculation From Eurocode 1
10 pages
BS En-12285-1
85% (13)
BS En-12285-1
159 pages
Structural Steel Design 1 Mini Project
No ratings yet
Structural Steel Design 1 Mini Project
24 pages
Wind Load Example
100% (2)
Wind Load Example
4 pages
Calculations Tank S6
100% (2)
Calculations Tank S6
19 pages
Fluid Flow Hydraulics Sizing and Selection Rev Web
100% (1)
Fluid Flow Hydraulics Sizing and Selection Rev Web
58 pages
EN 1993-1:2005/A1:2014, Eurocode 3: Design of Steel Structures
No ratings yet
EN 1993-1:2005/A1:2014, Eurocode 3: Design of Steel Structures
2 pages
Pos Fs - Calc Note
No ratings yet
Pos Fs - Calc Note
2 pages
EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures
No ratings yet
EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures
30 pages
RD Res
No ratings yet
RD Res
238 pages
EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures
No ratings yet
EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures
49 pages
Dijagonala2 Max
No ratings yet
Dijagonala2 Max
2 pages
DPGN
No ratings yet
DPGN
2 pages
EN 1993-1:2005/A1:2014, Eurocode 3: Design of Steel Structures
No ratings yet
EN 1993-1:2005/A1:2014, Eurocode 3: Design of Steel Structures
2 pages
GPGN
No ratings yet
GPGN
3 pages
03 300x300x118 Beam
No ratings yet
03 300x300x118 Beam
4 pages
Dimension I Mi
No ratings yet
Dimension I Mi
8 pages
Calculation Note
No ratings yet
Calculation Note
70 pages
Dijagonala Max
No ratings yet
Dijagonala Max
2 pages
Mbajtesi Kryesor, Prerjet Kritike
No ratings yet
Mbajtesi Kryesor, Prerjet Kritike
4 pages
OPTIMISATION
No ratings yet
OPTIMISATION
3 pages
1 (DL1) )
No ratings yet
1 (DL1) )
10 pages
STEEL DESIGN CALCULATION SHEET - USING AUTODESK ROBOT
No ratings yet
STEEL DESIGN CALCULATION SHEET - USING AUTODESK ROBOT
25 pages
Statika Totem 15m
No ratings yet
Statika Totem 15m
30 pages
Brandon
No ratings yet
Brandon
11 pages
EC3 Example Report
No ratings yet
EC3 Example Report
10 pages
Steel Design - Restrained Beams
No ratings yet
Steel Design - Restrained Beams
20 pages
Izračun Konzole Fermentora
No ratings yet
Izračun Konzole Fermentora
17 pages
Steel Design: Code: Analysis Type
No ratings yet
Steel Design: Code: Analysis Type
2 pages
Truss Design
No ratings yet
Truss Design
38 pages
EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures
No ratings yet
EN 1993-1:2005/AC:2009, Eurocode 3: Design of Steel Structures
3 pages
Portal Frame - Full Calc Note
No ratings yet
Portal Frame - Full Calc Note
5 pages
ExcelFEM - 2D (For Excel 2007 & Excel 2010)
No ratings yet
ExcelFEM - 2D (For Excel 2007 & Excel 2010)
248 pages
LRFD Beam Column Design
No ratings yet
LRFD Beam Column Design
242 pages
Steel Truss Calculation
No ratings yet
Steel Truss Calculation
15 pages
LRFD Beam Column Design
100% (1)
LRFD Beam Column Design
257 pages
RC Rectangular Column Design
No ratings yet
RC Rectangular Column Design
6 pages
Flexural Design of Singly Reinforced Beam Sections by LSM
No ratings yet
Flexural Design of Singly Reinforced Beam Sections by LSM
12 pages
8 No. 25 MM Diameter Longitudinal Bars Max Link Spacing 400 MM Generally, 240 MM For 500 MM Above and Below Slab/beam and at Laps
100% (1)
8 No. 25 MM Diameter Longitudinal Bars Max Link Spacing 400 MM Generally, 240 MM For 500 MM Above and Below Slab/beam and at Laps
7 pages
Steel 2D Analysis & Design (EN1993)
No ratings yet
Steel 2D Analysis & Design (EN1993)
4 pages
VMS Gantry Design
No ratings yet
VMS Gantry Design
14 pages
Abdulla Hasssan Assignment 1
No ratings yet
Abdulla Hasssan Assignment 1
42 pages
Capacity check example
No ratings yet
Capacity check example
7 pages
Lecture6 Compression Members
No ratings yet
Lecture6 Compression Members
38 pages
Seismic Design of R C and Steel
No ratings yet
Seismic Design of R C and Steel
38 pages
Column Analysis and Design v1
No ratings yet
Column Analysis and Design v1
8 pages
Steel Column
No ratings yet
Steel Column
4 pages
74m Bow String
No ratings yet
74m Bow String
49 pages
Analytical Study On Buckling Behaviour of
No ratings yet
Analytical Study On Buckling Behaviour of
107 pages
Flat Slab
No ratings yet
Flat Slab
79 pages
Project Title: Exercise 1
No ratings yet
Project Title: Exercise 1
2 pages
Salmerh StColDes
No ratings yet
Salmerh StColDes
5 pages
Lower Part of Two Storey Column Tedds
No ratings yet
Lower Part of Two Storey Column Tedds
5 pages
Steel Beam Design in LSM by IS Code
No ratings yet
Steel Beam Design in LSM by IS Code
116 pages
14 03 Flexural Buckling EC3
No ratings yet
14 03 Flexural Buckling EC3
37 pages
2810 Bracket Design Report
No ratings yet
2810 Bracket Design Report
12 pages
Steel Procedures
No ratings yet
Steel Procedures
39 pages
Lintel
No ratings yet
Lintel
9 pages
Simply Supported Beam Example
No ratings yet
Simply Supported Beam Example
4 pages
Ubkhep Ob Design Check
No ratings yet
Ubkhep Ob Design Check
72 pages
Design of Column
No ratings yet
Design of Column
3 pages
Steel Column Design
No ratings yet
Steel Column Design
10 pages
Design of Continuous Roof Beam
No ratings yet
Design of Continuous Roof Beam
8 pages
Applied Moment, Shear and Axial Loads
No ratings yet
Applied Moment, Shear and Axial Loads
8 pages
IBM System 360 RPG Debugging Template and Keypunch Card
From Everand
IBM System 360 RPG Debugging Template and Keypunch Card
Archive Classics
No ratings yet
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
No ratings yet
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
2 pages
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
No ratings yet
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
3 pages
Venting As Per Api 2000
100% (1)
Venting As Per Api 2000
6 pages
Is 6533 Part-1 Design of Construction of
50% (2)
Is 6533 Part-1 Design of Construction of
23 pages
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
No ratings yet
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
1 page
Plot Plan Course Notes
No ratings yet
Plot Plan Course Notes
9 pages
Module 5: Fire Fighting Foam Principles and Ethanol-Blended Fuel
No ratings yet
Module 5: Fire Fighting Foam Principles and Ethanol-Blended Fuel
32 pages
Tank Design MK
No ratings yet
Tank Design MK
18 pages
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
No ratings yet
Autodesk Robot Structural Analysis Professional 2012 Author: File: Structure2 (WITH LOADS) .RTD Address: Project: Structure2 (WITH LOADS)
1 page
Venting: As Per Section 4.3 of API 2000, Inbreathing
No ratings yet
Venting: As Per Section 4.3 of API 2000, Inbreathing
2 pages
Applus Reports Summary
No ratings yet
Applus Reports Summary
5 pages
Foam Calculation
No ratings yet
Foam Calculation
11 pages
Tank Design MK
No ratings yet
Tank Design MK
18 pages
Atmospheric Storage Tanks Venting Req API 2000 (6th ED 2009)
No ratings yet
Atmospheric Storage Tanks Venting Req API 2000 (6th ED 2009)
18 pages
Din 8075 PDF
100% (1)
Din 8075 PDF
11 pages
EN ISO 14310 (2008) (E) Codified
No ratings yet
EN ISO 14310 (2008) (E) Codified
8 pages
Topic 8 - Volume of Liquid: Paper 1
No ratings yet
Topic 8 - Volume of Liquid: Paper 1
12 pages
GSM Networks: Architecture, Protocols and Procedures
No ratings yet
GSM Networks: Architecture, Protocols and Procedures
202 pages
300t Mexican Calibrations June 2023
No ratings yet
300t Mexican Calibrations June 2023
4 pages
Qualifications Can Cross Boundaries
No ratings yet
Qualifications Can Cross Boundaries
4 pages
SI Units
No ratings yet
SI Units
24 pages
ISO Chat
No ratings yet
ISO Chat
1 page
GSM Vs CDMA
No ratings yet
GSM Vs CDMA
34 pages
Metrology and Calibration (METCAL)
No ratings yet
Metrology and Calibration (METCAL)
39 pages
WORKSHOP Engg. Dei
No ratings yet
WORKSHOP Engg. Dei
3 pages
Et Iso 5508 1990
No ratings yet
Et Iso 5508 1990
12 pages
IsiZulu HL P3 May June 2022
No ratings yet
IsiZulu HL P3 May June 2022
7 pages
3GPP TS 38.306
No ratings yet
3GPP TS 38.306
69 pages
Lamu Brochure
No ratings yet
Lamu Brochure
2 pages
7 - Jordanian Stanadrds For Lab JS EN ISO IEC 17025-2012 - A PDF
0% (1)
7 - Jordanian Stanadrds For Lab JS EN ISO IEC 17025-2012 - A PDF
2 pages
Iso 7965 2 1993
No ratings yet
Iso 7965 2 1993
9 pages
Iso 20515 2012
No ratings yet
Iso 20515 2012
14 pages
Measurement 1
No ratings yet
Measurement 1
2 pages
Cambridge International AS & A Level: Chemistry 9701/13 May/June 2021
No ratings yet
Cambridge International AS & A Level: Chemistry 9701/13 May/June 2021
3 pages
BS en Iso 3785-2006
No ratings yet
BS en Iso 3785-2006
18 pages
BS en Iso 5077-2008
No ratings yet
BS en Iso 5077-2008
10 pages
Rules of Clan
No ratings yet
Rules of Clan
1 page
JLPT Japanese-Language Proficiency Test - 【個人】個人申込画面（申込上の注意、受験上の注意等）1
No ratings yet
JLPT Japanese-Language Proficiency Test - 【個人】個人申込画面（申込上の注意、受験上の注意等）1
12 pages
Himalayan Garhwal Fee
No ratings yet
Himalayan Garhwal Fee
5 pages
Max 3747
No ratings yet
Max 3747
10 pages
Lenovo ThinkPad T460s BT460 NM-A421 Schematic Diagram
No ratings yet
Lenovo ThinkPad T460s BT460 NM-A421 Schematic Diagram
99 pages
Cit 853
No ratings yet
Cit 853
35 pages
Certificate of Registration: Information Security Management System - Iso/Iec 27001:2013
100% (1)
Certificate of Registration: Information Security Management System - Iso/Iec 27001:2013
2 pages