The BUA1 is a voltage and voltage balance relay that monitors three-phase voltages. It measures the amplitude and angle of voltages to determine phase sequence, and detects unbalance and phase loss. It can also monitor for undervoltage, overvoltage, and underfrequency. The BUA1 mounts on a DIN rail, has LED indicators, and contacts to signal faults. It is designed to protect three-phase systems from voltage issues.
The BUA1 is a voltage and voltage balance relay that monitors three-phase voltages. It measures the amplitude and angle of voltages to determine phase sequence, and detects unbalance and phase loss. It can also monitor for undervoltage, overvoltage, and underfrequency. The BUA1 mounts on a DIN rail, has LED indicators, and contacts to signal faults. It is designed to protect three-phase systems from voltage issues.
The BUA1 is a voltage and voltage balance relay that monitors three-phase voltages. It measures the amplitude and angle of voltages to determine phase sequence, and detects unbalance and phase loss. It can also monitor for undervoltage, overvoltage, and underfrequency. The BUA1 mounts on a DIN rail, has LED indicators, and contacts to signal faults. It is designed to protect three-phase systems from voltage issues.
The BUA1 is a voltage and voltage balance relay that monitors three-phase voltages. It measures the amplitude and angle of voltages to determine phase sequence, and detects unbalance and phase loss. It can also monitor for undervoltage, overvoltage, and underfrequency. The BUA1 mounts on a DIN rail, has LED indicators, and contacts to signal faults. It is designed to protect three-phase systems from voltage issues.
balance relay Application Supervision of voltage unbalance in three-phase systems, phase failure, phase sequence and under-/overvoltage.
Function The relay BUA1 measures amplitude and angle of three phase voltages. The angle of the phasors determine the phase sequence. Unbalance and phase loss are detected by the measurement of amplitude and angle. U characterizes the difference of the lowest to the highest phase-to-phase voltage related to nominal voltage. The underfrequency element trips if the frequency falls below 45 Hz.
Technical data rated voltage Un: frequency range: hysteresis: power consumption: thermal load carrying capacity: returning time: minimum operating time:
110 V, 230 V, 400 V AC
45 - 66 Hz 2% Un 4 VA continuously 1,3 x Un 600 ms 650 ms
Output relays: max. breaking capacity ohmic: 250 V AC/120 W DC inductive: 500 V AC/75 W DC rated current: 5A making current (16ms): 20 A
Fig. 1: Front plate
The unit BUA1 is designed to be fastened onto a DINrail acc. to DIN EN 50022 same as all units of the BASIC LINE. The front plate of the unit is protected with a sealable transparent cover (IP40). Please remove the transparent cover with a screw driver to adjust the relay.
LED LED U< is used to indicate operation without fault with steady light. The LED U> indicates overvoltage tripping with steady light. At undervoltage, U or underfrequency tripping the LED U< extinguishes.
110
Mechanical stress: shock: class 1 acc. to DIN IEC 255-21-2 vibration: class 1 acc. to DIN IEC 255-21-1
75
System data: regulations: VDE 0435 Teil 303 temperature range at storage and operation: - 25C bis + 70C
65
Fig. 2: Dimensional drawing of BUA1
degree of protection: weight: mounting position:
TB BUA1 09.95 E
IP 40 at closed front cover
approx. 0,5 kg any
Auxiliary voltage supply
The unit BUA1 needs no separate auxiliary voltage supply. The supply voltage can be formed directly from the measuring quantity.
Operation without a fault
Unit dead, undervoltage
wrong phase sequence, or underfrequency
Overvoltage Fig. 3: Connection diagram
Fig. 4: Contact positions
Connection terminals The connection up to a maximum of 2 x 2,5 mm cross-section conductors is possible. For this procedure the transparent cover of the unit has to be removed.
Setting ranges U: 5 - 15 % Un tU: 0 - 10 s U<: 70 - 110 % Un U>: 90 - 130 % Un
Order key: quantity BUA1 110 V AC 230 V AC 400 V AC
