Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
266 views

Turbine Alignment

This document discusses laser alignment of steam turbine internals as an alternative to traditional piano wire alignment methods. It provides an example of laser alignment being used successfully on a 450-MW steam turbine at a Pacific Rim utility. Key points: - Laser alignment is faster, more accurate, and can measure to a tolerance of 2-4 mils compared to piano wire which is time-consuming and requires multiple setups. - On the Pacific Rim turbine, laser alignment reduced outage time by 3 days and resulted in tight clearances and no rubs post-overhaul. - Laser alignment equipment can automatically compensate for environmental influences and allows flexible measurement of bore geometry at multiple points. - Proper laser setup

Uploaded by

Guru Raja Ragavendran Nagarajan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
266 views

Turbine Alignment

This document discusses laser alignment of steam turbine internals as an alternative to traditional piano wire alignment methods. It provides an example of laser alignment being used successfully on a 450-MW steam turbine at a Pacific Rim utility. Key points: - Laser alignment is faster, more accurate, and can measure to a tolerance of 2-4 mils compared to piano wire which is time-consuming and requires multiple setups. - On the Pacific Rim turbine, laser alignment reduced outage time by 3 days and resulted in tight clearances and no rubs post-overhaul. - Laser alignment equipment can automatically compensate for environmental influences and allows flexible measurement of bore geometry at multiple points. - Proper laser setup

Uploaded by

Guru Raja Ragavendran Nagarajan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

DESIGN/OPERATING IDEAS

Turbine alignment:
Time is money
Ludeca Incs Dieter Seidenthal was
talking about laser alignment of
steam-turbine internalsas he often
doeswhen the editors of the COMBINED CYCLE Journal bumped
into him at Power-Gen International
late last year. The subject that day
was that after more than 10 years
of successful experience in powerplants with laser bore alignment,
there were still turbine users relying
on piano wire and dummy shafts.
Seidenthal had no problem reciting
the reasons why this is so: no personnel trained for the task, people are
comfortable with piano wire because
theyve done it before, and, of course,
instrumentation costs money.
First some background. A
well-known fact is that bore alignment of bearing pockets, seals, and
diaphragms can be time-consuming
tasks in the overhaul of turbines
something most combined-cycle
plants have several ofif you rely on
piano wire, micrometers, and optical instruments. Thats why turbine
manufacturers and specialty service
companies have embraced systems
such as Centralign, a registered
trademark of Germanys Prueftechnik AG, distributed exclusively in the
US by Miami-based Ludeca.
Centralign uses a visible-laser
emitter and intelligent sensor to
determine the centerline position
of bearing pockets with micron
accuracy, even over separations of
more than 100 ft. All readings are
transmitted via cordless infrared
link to a computer which automatically plots an alignment diagram of
all measurement points, along with
their offsets from the laser reference
line. The reference can be shifted to
any desired position in the display
so that the offsets are recalculated
automatically; the laser eliminates
the oft-troublesome pre-leveling and
sag compensation.
Seidenthal (305-591-8935,
dieter@ludeca.com) says the costof-instrumentation and no-qualified-personnel arguments rarely are
validif ever. By way of example,
he points to recent experience at
a Pacific Rim utility on a 450-MW
steam turbine. The company had
never before attempted to implement
internals alignment with a laser. As

a result, he says, the project had a


high profile within the utility. To be
on the safe side, the same amount of
time that normally would have been
allocated for piano-wire measurement was allotted for laser alignment in critical-path planning.
Scope of work for the alignment
team included:
Laser bore alignment measurement of the high-pressure/
intermediate-pressure section
diaphragms, casings, and seals to
achieve OEM tolerances (2 mils
was considered excellent, 4 mils
satisfactory).
Provide technical support, and
training of personnel nominated
by the utility to learn laser bore
alignment.
Supply set-up measurements.
The bottom line: Outage time
was reduced by three days compared

Laser bore alignment is faster, more


accurate than traditional piano-wire
method. Shown is the laser setup on
the front standard of a steam turbine
to that formerly required when the
piano-wire method was used for
alignment. Result was tight clearances and no rubs. The long-term
payoff, of course, is improved turbine
efficiency and reduced packing wear.
One reason for the dramatic
reduction in time to complete the
alignment check when a laser system
is used is that it normally takes only
one setup requiring about half an
hour to accomplish most bore measurement needs for the entire outage. The piano-wire method requires
setup and teardown each time move
verification is undertaken (internals
cannot be adjusted with piano wire
in place).
As with any light source, continues Seidenthal, lasers also may be
affected by atmospheric conditions.
And, as when using piano wire, conditions may change original refer-

COMBINED CYCLE JOURNAL, First Quarter 2005

ences over the time it takes to conduct comprehensive measurements.


The laser system for this project was
able to measure and compensate
each measured bore automatically
for any external or environmental
influences.
Setup of the laser system is relatively simple with a modest amount
of training. The general procedure
consists of installing the laser on the
front standard (photo). A measurement sensorreferred to as the control sensoris installed at the end of
the measurement string to monitor
and store changes in laser position
caused by external and environmental effects. Individual bore measurements can be adjusted by measured
laser variances at the operator s
discretion.
Various types of bracketing are
available, allowing the operator to
sweep any bore of interest. For
this project, the list included all diaphragms, gland packing bores, oil
deflectors, and the nozzle box. The
operator can measure a bore at many
points around its circumference, permitting a meaningful assessment of
geometry. The equipment is flexible
enough to allow different modes of
measurementone even emulates
the piano-wire method by taking
data at the top, bottom, left, and
right positions.
Finally, keep in mind that diaphragm bore positions change
depending on whether or not the
top half of the casing is installed. To
assure optimum final bore positions,
data sets for the measurement string
were conducted under two separate
assembly conditionsso-called top
on and top off.

Balloon keeps
HRSG warm
Balloon?
A problem faced by engineers
today is that their combined-cycle
plants are not operating base-load
as owners thought they would be
when designed. Thus auxiliaries and
extras that would have facilitated
cycling service and simplified periodic shutdowns lasting for days (sometimes as long as several weeks) were
not considered. No need; so owners
thought.
One such extra is a stack damper.
It can prevent rapid cool-down of
81

You might also like