Energy Division

Metal Oxide Surge Arresters for Distribution Networks up to 110 kV

Metal Oxide Surge Arrester for Distribution Networks

Content

Voltage

Page

Tyco Electronics Experience and Design

Outdoor and Indoor Application Line Discharge Class 1 (HDA-MA) Line Discharge Class 1 (HDA-M) Line Discharge Class 1 (DA1) Line Discharge Class 2 (OCP) Line Discharge Class 2 (HSR) Line Discharge Class 3 (PCA) Accessories for type HDA Accessories for type DA1 Accessories for type OCP Accessories for type HSR and PCA 3 to 24 kV 26 to 41 kV 6 to 15 kV 3 to 41 kV 48 to 110 kV 48 to 110 kV 4 6 8 10 12 14 16 17 18 19

Indoor Applications in gas insulated switchgear systems (RDA, RSTI-SA) in air-spaced switchgear systems (SPA) in motor-connection boxes (MPA) 6 to 41 kV 6 to 36 kV 2 to 12 kV 20 22 23

Special Applications for transformers (MORE) at covered conductors (CLX) as cable sheath protection (CPA) in A.C. Railway networks (HDA) in D.C. Railway networks (HE60) 12 to 36 kV 12 to 36 kV 1 to 7 kV 27 to 33 kV 0,7 to 4,5 kV 24 25 26 27 27

Low Voltage Networks at overhead lines, and distribution transformers 0,28 to 0,44 kV 28

Tyco Electronics commitment to quality and reliability

30 1

Metal Oxide Surge Arresters

Tyco Electronics Experience Tyco Electronics Energy Division pioneered the development of polymeric housed surge arresters in the early 1980's and have a proven service experience across the globe, operating in the worlds toughest environments. Tyco Electronics polymeric surge arresters type Raychem and Bowthorpe have been designed and tested to meet the requirements of IEC60099-4, Ed. 2, 2004. The qualification was performed in independent laboratory facilities in Europe.

Exceeds requirements of IEC-60099-4 Ed. 2.0 for polymeric zinc oxide arresters documented by test reports of independent test institutes Superior protection margins by low residual voltages, high energy handling and high TOV values Excellent mechanical, vibration and impact withstand capability Void-free design by direct molded housing on Metal Oxide blocks and aluminium fittings Direct bonding of housing to fittings ensures optimum moisture barrier Track and erosion resistant housing with more than 40 years experience in all climatic conditions Safe non-shattering short circuit behaviour to higher current levels Maintenance free construction Certified to GOST standard and approved by Federal Networks of Russia and Ukraine Scientific Research and Engineering Institute

Designed to meet your individual requirements Tyco Electronics developed Surge Arresters for different voltages, classes and a lot of different applications. To meet the individual application requirements our arresters can be adapted with a large variety of available line-, earth- and mountingterminal modules. Surge Arresters for Distribution Networks are shown in this catalogue. Surge Arresters for higher discharge classes and voltages are documented in our High Voltage Surge Arrester Catalogue.

Metal Oxide Surge Arresters

HDA, OCP and PCA are the newest gapless, zinc oxide Raychem and Bowthorpe arrester families. The development of these products is based on 25 years of experience in arrester design and manufacture within the Tyco Electronics Energy Division. The final qualifications were performed in independent laboratory facilities in Europe. All arrester types are manufactured using superior ZnO varistors, which display excellent thermal and current handling characteristics due to the guaranteed homogeneity of the varistor volume. This superior thermal behaviour yields products with: Excellent TOV performance. Safe, non-shattering failure in the short circuit test by pre-failing to higher fault currents. High energy handling capability. The crimped structural construction ensures a light weight arrester with optimal mechanical strength. The manufacturing process ensures void free construction and optimum interface sealing. This is achieved by bonding the polymeric housing directly to the ZnO discs and aluminium fittings using a Tyco Electronics proprietary bonding solution. The polymer housing was developed using the knowledge accumulated over 40 years of materials science expertise and experience, resulting in an optimum shed profile and a material with excellent tracking and erosion resistance.

The design of the Tyco Electronics Surge Arrester comprises of: 1 - ZnO (Zinc Oxide) varistors 2 - Tyco Electronics proprietary polymeric housing 3 - Flame retardant fiber reinforced crimping structure 4 - Corrosion resistant aluminium fittings

Excellent hydrophobicity

Safe non-shattering failure mode

Track and erosion resistance

Discharge Class 1 Surge Arrester HDA-MA

Generic technical data: HDA-xxMA series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temporary overvoltage, (UTOV/UC): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 2 long duration impulses 2 high current impulses Ambient temperature: 3-24 kV Uc 10 kA Class 1 100 kA 400 A 1,42 40 kA 4,2 kJ/kV Uc 6,8 kJ/kV Uc - 60C to + 60C

Mechanical strength data Cantilever Tensile Torque 350 Nm 2000 N 50 Nm

Temporary Overvoltage (TOV) of HDA-xxMA with prior energy 1,60 1,55 1,50 1,45 1,40 UTOV / UC 1,35 1,30 1 Time (s) Samples are pre-heated to a temperature of 60 C according to IEC 60099-4, Ed 2,0 2004. Samples were subjected to a pre-stress equivalent to one high current impulse of 100kA, 4/10 s as per switching surge operating duty test. UTOV = TOV withstand voltage; UC = continuous operating voltage TOV Curve

10

100

1000

10000

Discharge Class 1 Surge Arrester HDA-MA

Protective Characteristics HDA-MA Uc kV

Ur kV

HDA-03MA-xxx HDA-04MA-xxx HDA-06MA-xxx HDA-08MA-xxx HDA-09MA-xxx HDA-10MA-xxx HDA-12MA-xxx HDA-18MA-xxx HDA-20MA-xxx HDA-21MA-xxx HDA-24MA-xxx

3 4 6 8 9 10 12 18 20 21 24

3,7 5,0 7,5 10,0 11,2 12,5 15,0 22,5 25,0 26,2 30,0

Ures in kV when tested to impulse waveforms Lightning Steep lightning (8/20s) (1/20s) 5kA 10kA 20kA 10kA 9,3 9,9 10,9 10,2 12,4 18,6 24,8 27,9 31,0 37,2 55,8 62,0 65,1 74,4 13,2 19,8 26,4 29,7 33,0 39,6 59,4 66,0 69,3 79,2 14,6 21,8 29,1 32,8 36,4 43,7 65,5 72,8 76,4 87,4 13,6 20,4 27,2 30,6 34,0 40,8 61,2 68,0 71,4 81,6

Switching (30/60s) 125A 500A 7,4 7,9 9,8 14,8 19,7 22,1 24,6 29,5 44,3 49,2 51,7 59,0 10,5 15,7 21,0 23,6 26,2 31,4 47,2 52,4 55,0 62,9

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage

Standard Housing Parameter HDA-MA Impulse voltage 1.2/50s

HDA-03MA-xxx HDA-04MA-xxx HDA-06MA-xxx HDA-08MA-xxx HDA-09MA-xxx HDA-10MA-xxx HDA-12MA-xxx HDA-18MA-xxx HDA-20MA-xxx HDA-21MA-xxx HDA-24MA-xxx

(kV) 106 106 106 106 106 106 106 190 190 190 190

Power frequency voltage withstand, wet (kV) 47 47 47 47 47 47 47 93 93 93 93

Flash over distance

Creepage length

Height L

Weight

(mm) 176 176 176 176 176 176 176 310 310 310 310

(mm) 380 380 380 380 380 380 380 830 830 830 830

(mm) 183 183 183 183 183 183 183 316 316 316 316

(kg) 1,80 1,80 1,80 1,80 1,80 1,80 1,80 3,25 3,25 3,25 3,25
L

104 mm 123 mm

To complete the order information for the accessories, please refer to page 16. 5

Discharge Class 1 Surge Arrester HDA-M

Generic technical data: HDA-xxM series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temporary overvoltage, (UTOV/UC): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 2 long duration impulses 2 high current impulses Ambient temperature: 26-41 kV Uc 10 kA Class 1 100k A 400 A 1,42 40 kA 4,2 kJ/kV Uc 6,8 kJ/kV Uc - 60C to + 60C

Mechanical strength data Cantilever Tensile Torque 250 Nm 2000 N 50 Nm

Temporary Overvoltage (TOV) of HDA-xxM with prior energy 1,60 1,55 1,50 1,45 1,40 UTOV / UC 1,35 1,30 1 Time (s) Samples are pre-heated to a temperature of 60 C according to IEC 60099-4, Ed 2,0 2004. Samples were subjected to a pre-stress equivalent to one high current impulse of 100kA, 4/10 s as per switching surge operating duty test. UTOV = TOV withstand voltage; UC = continuous operating voltage TOV Curve

10

100

1000

10000

Discharge Class 1 Surge Arrester HDA-M

Protective Characteristics HDA-M Uc kV

Ur kV

HDA-26M-xxx HDA-27M-xxx HDA-29M-xxx HDA-30M-xxx HDA-33M-xxx HDA-36M-xxx HDA-39M-xxx HDA-40M-xxx HDA-41M-xxx

26 27 29 30 33 36 39 40 41

32,5 33,7 36,2 37,5 41,2 45,0 48,7 50,0 51,2

Ures in kV when tested to impulse waveforms Lightning Steep lightning (8/20s) (1/20s) 5kA 10kA 20kA 10kA 80,6 85,8 94,6 88,4 83,7 89,9 93,0 102,3 111,6 120,9 124,0 127,1 89,1 95,7 99,0 108,9 118,8 128,7 132,0 135,3 98,3 105,6 109,2 120,1 131,0 142,0 145,6 149,2 91,8 98,6 102,0 112,2 122,4 132,6 136,0 139,4

Switching (30/60s) 125A 500A 64,0 68,1 66,4 71,3 73,8 81,2 88,6 95,9 98,4 100,9 70,7 76,0 78,6 86,5 94,3 102,2 104,8 107,4

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage

Standard Housing Parameter HDA-M Impulse voltage 1.2/50s

HDA-26M-xxx HDA-27M-xxx HDA-29M-xxx HDA-30M-xxx HDA-33M-xxx HDA-36M-xxx HDA-39M-xxx HDA-40M-xxx HDA-41M-xxx

(kV) 204 204 204 204 228 228 250 250 250

Power frequency voltage withstand, wet (kV) 98 98 98 98 110 110 122 122 122

Flash over distance

Creepage length

Height L

Weight

(mm) 339 339 339 339 378 378 418 418 418

(mm) 970 970 970 970 1125 1125 1279 1279 1279

(mm) 343 343 343 343 383 383 423 423 423

(kg) 4,00 4,00 4,00 4,00 4,50 4,50 5,00 5,00 5,00
L

107 mm 137 mm

To complete the order information for the accessories, please refer to page 16. 7

Discharge Class 1 Surge Arrester DA1

Generic technical data: DA1 series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): 10 second Temporary Overvoltage (UTOV/UC): Long duration current impulse (2000s): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 2 long duration impulses Ambient temperature: 6-15 kV Ur 10 kA Class 1 100 kA 1,29 325 A 21 kA 5,6 kJ/kV - 60C to + 60C

Mechanical strength data Cantilever Tensile Torque 350 Nm 2000 N 50 Nm

Temporary Overvoltage (TOV) of DA1 with prior energy 1.7 1.6 1.5 1.4 1.3 UTOV / UC 1.2 1.1 1.0 0,1 Time (s) TOV Curve

10

100

1000

10000

Samples are pre-heated to a temperature of 60 C according to IEC 60099-4, Ed 2,0 2006. Sample was subjected to a pre-stress equivalent to one high current impulse of 100kA, 4/10 s as per switching surge operating duty test. UTOV = TOV withstand voltage; UC = continuous operating voltage

Discharge Class 1 Surge Arrester DA1

Protective Characteristics DA1 Uc kV DA1-08A-xxxxxx-I DA1-10A-xxxxxx-I DA1-12A-xxxxxx-I DA1-15B-xxxxxx-I 6,4 8,0 9,6 12,0

Ur kV 8 10 12 15

U res in kV when tested to impulse waveforms Lightning (8/20s) Steep lightning (1/20s) 5kA 10kA 20kA 10kA 19,9 21,2 23,2 22,3 24,9 29,9 37,3 26,5 31,8 39,8 29,1 34,9 43,6 27,9 33,4 41,8

Switching (30/60s) 125A 500A 15,9 16,9 19,9 23,9 29,9 21,1 25,3 31,6

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage

Standard Housing Parameter DA1 Impulse Housing Voltage code 1.2/50s (kV) 134 134 134 160

DA1-08A-xxxxxx-I DA1-10A-xxxxxx-I DA1-12A-xxxxxx-I DA1-15B-xxxxxx-I

Power Frequency voltage withstand, wet (kV) 50 50 50 56

Flash Over Distance (mm) 152 152 152 177

Creepage Length

Height L

Weight

(mm) 329 329 329 404

(mm) 147 147 147 172

(kg) 1,2 1,2 1,2 1,4

50mm 104mm

To complete the order information for the accessories, please refer to page 17. 9

Discharge Class 2 Surge Arrester OCP

Generic technical data: OCP2 series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): 10 second Temporary Overvoltage (UTOV/UC): Long duration current impulse (2000s): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 2 long duration impulses Ambient temperature: 40 kA 6,0 kJ/kV Uc - 60C to + 60C 3-41 kV Uc 10 kA Class 2 100 kA 1,35 530 A

Mechanical strength data Cantilever Tensile Torque 250 Nm 2000 N 50 Nm

Temporary Overvoltage (TOV) of OCP2 with prior energy 1,60 1,50 1,40 1,30 UTOV / UC 1,20 1,10 1 Time (s) TOV Curve

10

100

1000

10000

Samples are pre-heated to a temperature of 60 C according to IEC 60099-4, Ed 2,0 2004. Sample was subjected to a pre-stress equivalent to one high current impulse of 100kA, 4/10 s as per switching surge operating duty test. UTOV = TOV withstand voltage; UC = continuous operating voltage

10

Discharge Class 2 Surge Arrester OCP

Protective Characteristics OCP2 Uc kV OCP2-03S-xxx OCP2-04S-xxx OCP2-06S-xxx OCP2-08S-xxx OCP2-09S-xxx OCP2-10S-xxx OCP2-12S-xxx OCP2-18S-xxx OCP2-20S-xxx OCP2-21S-xxx OCP2-24S-xxx OCP2-27S-xxx OCP2-30M-xxx OCP2-33M-xxx OCP2-36M-xxx OCP2-39M-xxx OCP2-40M-xxx OCP2-41M-xxx 3 4 6 8 9 10 12 18 20 21 24 27 30 33 36 39 40 41

Ur kV 3,7 5,0 7,5 10,0 11,2 12,5 15,0 22,5 25,0 26,2 30,0 33,7 37,5 41,2 45,0 48,7 50,0 51,2

U res in kV when tested to impulse waveforms Lightning (8/20s) Steep lightning (1/20s) 5kA 10kA 20kA 10kA 9,18 9,72 10,84 10,10 12,24 18,36 24,48 27,54 30,60 36,72 55,08 61,20 64,26 73,44 82,60 91,80 101,00 110,20 119,30 122,40 125,50 12,96 19,44 25,92 29,16 32,40 38,88 58,32 64,80 68,04 77,76 87,50 97,20 106,90 116,60 126,40 129,60 132,80 14,46 21,68 28,91 32,53 36,14 43,37 65,05 72,28 75,89 86,74 97,60 108,40 119,30 130,10 140,90 144,60 148,20 13,47 20,21 26,94 30,31 33,68 40,42 60,62 67,36 70,73 80,83 90,90 101,00 111,10 121,20 131,40 134,70 138,10

Switching (30/60s) 125A 500A 7,37 7,76 9,83 14,75 19,66 22,12 24,58 29,50 44,24 49,16 51,62 58,99 66,40 73,70 81,10 88,50 95,90 98,30 100,80 10,35 15,53 20,70 23,29 25,88 31,06 46,58 51,76 54,35 62,11 69,90 77,60 85,40 93,20 100,90 103,50 106,10

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage

Standard Housing Parameter OCP2 Impulse Power Voltage Frequency 1.2/50s voltage withstand, wet (kV) (kV) OCP2-03S-xxx 145 47 OCP2-04S-xxx OCP2-06S-xxx OCP2-08S-xxx OCP2-09S-xxx OCP2-10S-xxx OCP2-12S-xxx OCP2-18S-xxx OCP2-20S-xxx OCP2-21S-xxx OCP2-24S-xxx OCP2-27S-xxx OCP2-30M-xxx OCP2-33M-xxx OCP2-36M-xxx OCP2-39M-xxx OCP2-40M-xxx OCP2-41M-xxx 145 145 145 145 145 145 180 180 200 200 230 204 228 228 250 250 250 47 47 47 47 47 47 70 70 80 80 95 98 110 110 122 122 122

Flash Over Distance (mm) 176 176 176 176 176 176 176 254 254 293 293 334 339 378 378 418 423 423

Creepage Length

Height L

Weight

(mm) 380 380 380 380 380 380 380 632 632 758 758 885 970 1125 1125 1279 1279 1279

(mm) 183 183 183 183 183 183 183 260 260 299 299 340 343 383 383 423 423 423

(kg) 1,80 1,80 1,80 1,80 1,80 1,80 1,80 2,65 2,65 3,00 3,00 3,40 3,65 4,15 4,15 4,65 4,65 4,65
up to 41 kV 107 mm 137 mm up to 29 kV 97 mm 119 mm L

To complete the order information for the accessories, please refer to page 18. 11

Discharge Class 2 Surge Arrester HSR

Generic technical data: HSR series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temporary overvoltage (UTOV/UC): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 2 long duration impulses Ambient temperature: up to 110 kV Ur 10 kA Class 2 100 kA 530 A 1,13 40 kA 6,0 kJ/kV Uc - 60C to + 60C

Mechanical strength data Cantilever (2HSRC/3HSRC) Tensile Torque 900/600 Nm 2000 N 75 Nm

Temporary Overvoltage (TOV) of HSR with prior energy 1,25 1,20 TOV Curve 1,15 1,10 1,05 UTOV / UC 1,00 0,95 1 Time (s)

10

100

1000

10000

Temperature of samples (pre-heated): 60 C according to IEC 60099-4, Ed 2.0 2004. TOV Curve applies to an arrester which has a pre-stress applied prior to TOV verification. This pre-stress is equivalent to two long duration current impulses of 2000 s with total energy capability 5.6 kJ/kV Uc. UTOV = TOV withstand voltage UC = continuous operating voltage

12

Discharge Class 2 Surge Arrester HSR

Protective Characteristics HSRC Uc kV

Ur kV

2HSRCP48LxExMx 2HSRCP60LxExMx 2HSRCP72LxExMx 2HSRCP75LxExMx 3HSRCP84LxExMx 3HSRCP88LxExMx 3HSRCP91LxExMx 3HSRCP95LxExMx 3HSRCP96LxExMx 3HSRCP99LxExMx 3HSRCP102LxExMx 3HSRCP106LxExMx 3HSRCP108LxExMx 3HSRCP110LxExMx

38,4 48,0 57,6 60,0 67,0 70,0 73,0 76,0 76,8 79,0 82,0 85,0 86,4 88,0

48,0 60,0 72,0 75,0 84,0 87,5 91,2 95,0 96,0 98,7 102,5 106,2 108,0 110,0

Ures in kV when tested to impulse waveforms Lightning Steep Switching lightning (8/20s) (1/200s) (30/60s) 5kA 10kA 20kA 10kA 20kA 250A 500A 120 129 142 139 153 97,8 101 148 179 185 209 219 225 237 238 243 256 265 269 271 159 192 199 225 235 242 255 258 261 275 285 291 291 175 212 219 248 259 266 281 284 288 303 314 321 321 171 206 213 242 252 259 274 274 281 295 306 309 313 189 228 236 267 279 287 302 302 310 326 338 342 346 120 146 151 171 178 183 193 193 198 208 216 218 221 125 150 156 176 184 189 200 201 205 215 223 227 228

1000A 105 129 156 162 183 192 197 208 208 213 224 232 235 237

2000A 110 136 164 170 192 201 206 218 218 223 235 243 246 249

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage

Standard housing parameters HSRC Impulse Voltage 1.2/50s (kV) 503 503 503 503 757 757 757 757 757 757 757 757 757 757

2HSRCP48LxExMx 2HSRCP60LxExMx 2HSRCP72LxExMx 2HSRCP75LxExMx 3HSRCP84LxExMx 3HSRCP88LxExMx 3HSRCP91LxExMx 3HSRCP95LxExMx 3HSRCP96LxExMx 3HSRCP99LxExMx 3HSRCP102LxExMx 3HSRCP106LxExMx 3HSRCP108LxExMx 3HSRCP110LxExMx

Power Frequency voltage withstand, wet (kV) 273 273 273 273 377 377 377 377 377 377 377 377 377 377

Flash Over Distance (mm) 964 964 964 964 1446 1446 1446 1446 1446 1446 1446 1446 1446 1446

Creepage Length

Height L

Weight

(mm) 2650 2650 2650 2650 3975 3975 3975 3975 3975 3975 3975 3975 3975 3975

(mm) 952 952 952 952 1428 1428 1428 1428 1428 1428 1428 1428 1428 1428

(kg) 11,2 11,2 11,2 11,2 16,8 16,8 16,8 16,8 16,8 16,8 16,8 16,8 16,8 16,8
L

To complete the order information for the accessories, please refer to page 19. 13

Discharge Class 3 Surge Arrester PCA

Generic technical data: PCA series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second TOV (UTOV/UC): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 2 long duration impulses Ambient temperature: up to 110 kV Ur 10 kA Class 3 100 kA 640 A 1,15 65 kA 7,8 kJ/kV Uc - 60C to + 60C

Mechanical strength data Cantilever Tensile Torque 2500 Nm 75 kN 75 Nm

Temporary Overvoltage (TOV) of PCR with prior energy 1,2

TOV Curve 1,1

1,0 UTOV / UC

0,9 1 Time (s)

10

100

1000

10000

Temperature of samples (pre-heated): 60 C according to IEC 60099-4, Ed 2.0 2004. TOV Curve applies to an arrester which has a pre-stress applied prior to TOV verification. This pre-stress is equivalent to two long duration current impulses of 2000 s with total energy capability 5.6 kJ/kV Uc. UTOV = TOV; UC =

14

Discharge Class 3 Surge Arrester PCA

Protective Characteristics PCA Uc kV

Ur kV

PCA248LxExMx PCA260LxExMx PCA372LxExMx PCA375LxExMx PCA384LxExMx PCA396LxExMx PCA3108LxExMx

38.4 48.0 57.6 60.0 67.2 76.8 86.4

48 60 72 75 84 96 108

Ures in kV when tested to impulse waveforms Lightning Steep Switching lightning (8/20s) (1/200s) (30/60s) 5kA 10kA 20kA 10kA 20kA 250A 500A 123 129 141 140 152 99,7 103 149 180 185 209 234 259 156 188 193 219 245 270 170 206 212 240 268 296 169 205 210 238 266 294 184 223 228 259 289 320 120.0 146.0 150.0 169.0 189.0 209.0 124 151 155 173 196 216

1000A 106 128 155 159 180 201 222

2000A 111 134 162 166 188 211 233

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage

Standard housing parameters PCA Impulse Voltage 1.2/50s (kV) 325 325 650 650 650 650 650

PCA248LxExMx PCA260LxExMx PCA372LxExMx PCA375LxExMx PCA384LxExMx PCA396LxExMx PCA3108LxExMx

Power Frequency voltage withstand, wet (kV) 140 140 275 275 275 275 275

Flash Over Distance (mm) 566 566 1059 1059 1059 1059 1059

Creepage Length

Height L

Weight

(mm) 1815 1815 3625 3625 3625 3625 3625

(mm) 655 655 1150 1150 1150 1150 1150

(kg) 14,0 14,0 26,5 26,5 26,5 26,5 26,5

To complete the order information for the accessories, please refer to page 19. 15

Accessories for Class 1 Surge Arrester (Type HDA)

Line lead accessories

F
45mm 65mm

H
45mm

Arrester Type = Continuous Operating Voltage Uc in kV 03MA 15MA 26M 04MA 16MA 27M 05MA 06MA 08MA 09MA 10MA 12MA 14MA 17MA 18MA 19MA 20MA 21MA 22MA 24MA 29M 30M 33M 36M 39M 40M 41M

HDA0

ABC

Mounting accessories

A
Ground lead accessories

45mm

45mm

65mm

Installation Requirements

System Voltage U0/U 6/10 12/20 20/35

ph/ph (a) 185 315 510

ph/ground (b) 165 295 490

16

Accessories for Class 1 Surge Arrester (Type DA1)

Line lead accessories

Arrester Type = Rated Voltage Ur in kV

08A 12A

10A

DA1
15B

0 0 0-I

Ground lead accessories

F
Mounting accessories

Installation Requirements

System Voltage U0/U 6/10 12/20 20/35

ph/ph (a) 185 315 510

ph/ground (b) 165 295 490

17

Accessories for Class 2 Surge Arrester (Type OCP2)

Line lead accessories

F
55mm

M
55mm

Arrester Type = Continuous Operating Voltage Uc in kV 03S 12S 30M 04S 18S 33M 06SA 08S 20S 36M 21S 39M 09S 24S 40M 10S 27S 41M

OCP20

ABC

All accessories with M12 stainless steel studs Mounting accessories

A
Ground lead accessories

55mm

55mm

Installation Requirements

System Voltage U0/U 6/10 12/20 20/35

ph/ph (a) 185 315 510

ph/ground (b) 165 295 490

18

Accessories for Class 2 and Class 3 Surge Arrester (Type HSR and PCA)
Line lead accessories

L1

L2

L5

L6

50 mm stud with washers and nut M16

Line Clamp to suit conductors up to 16 mm

Line Clamp to suit conductors up to 35 mm

Aluminium Stem 30 x 80mm high

Arrester Type = Rated Voltage Ur in kV

2HSRCP

3HSRCP 108

HSRCP

48 60 72 75 84 96 PCA2

PCA3

PCA

Earthing accessories

E1

E2

E5

2 x M10 x 20mm Hexagon headed set screws and spring washers

Earth Clamp to suit conductors up to 16 mm

Line Clamp to suit conductors up to 35 mm

Mounting accessories

M5

M3

M4

M8

HSRCP or PCA 4 hole pedestal base HSRCP: 127-140 PCO PCA: 200-254 PCO

HSRCP Set of 4 89 x 76 Polyfibre Base Insulators supplied with M5 Pedestal Base

PCA Set of 4 89 x 76 Polyfibre Base Insulators supplied with M5 Pedestal Base

PCA Set of 3 89 x 76 Polyfibre Base Insulators supplied with M5 Pedestal Base

Ur kV 48 60 72 75 84 88 91 95 96 99 102 106 108 110

HSRCP

PCA

2HSRCP48LxExMx 2HSRCP60LxExMx 2HSRCP72LxExMx 2HSRCP75LxExMx 3HSRCP84LxExMx 3HSRCP88LxExMx 3HSRCP91LxExMx 3HSRCP95LxExMx 3HSRCP96LxExMx 3HSRCP99LxExMx 3HSRCP102LxExMx 3HSRCP106LxExMx 3HSRCP108LxExMx 3HSRCP110LxExMx

PCA248LxExMx PCA260LxExMx PCA272LxExMx PCA275LxExMx PCA384LxExMx PCA388LxExMx PCA391LxExMx PCA395LxExMx PCA396LxExMx PCA399LxExMx PCA3102LxExMx PCA3106LxExMx PCA3108LxExMx PCA310LxExMx

Recommended minimum distance mm between phase centers line to earth HSRCP PCA HSRCP 510 542 260 625 654 326 735 767 391 765 795 408 840 880 456 1213 993 518 1213 993 518 1213 993 518 1213 993 518 1326 1106 583 1326 1106 583 1326 1106 583 1326 1106 583 1436 1218 648

PCA 306 372 437 453 502 567 567 567 567 632 632 632 632 698

19

MV Surge Arresters for Indoor Applications RDA

In gas-insulated switchgear systems RDA type Modern gas-insulated switchgear connected to combined underground and overhead distribution systems are sensitive to effects like transient voltage doubling. An arrester installed right at the cable end will clamp the voltage to a level which does not put the switchgear at risk. The RDA surge arrester, together with the Raychem RICS connection system for gas-insulated switchgear, facilities at hermetically sealed integration of the arrester and the cable termination to be connected to a switchgear. Compact design and easy installation are the special features of this product line.

222 195

222 min 50

Gas insulated switchgear with RDA arrester and RICS adapter. RICS adapter must be ordered seperatly. Generic technical data: RDA-xx series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temprary overvoltage (UTOV/UC) High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy line discharge impulse high current impulse 6-24 kV Uc 10 kA Class 1 100 kA 400 A 1,25 16 kA 2,6 kJ/kV Uc 5,3 kJ/kV Uc RDA-06 RDA-09 RDA-12 RDA-15 RDA-18 RDA-21 RDA-24 RDA Height L (mm) 138+222 168+222 200+222 299+222 329+222 361+222 393+222

Protective Characteristics RDA Uc kV

Ur kV

RDA-06 RDA-09 RDA-10 RDA-12 RDA-15 RDA-18 RDA-21 RDA-24

6 9 10 12 15 18 21 24

7,5 11,0 12,5 15,0 18,0 22,0 26,0 30,0

Ures in kV when tested to impulse waveforms Lightning Steep lightning (8/20s) (1/20s) 5kA 10kA 20kA 40kA 10kA 18,6 20,0 22,4 26,2 21,8 27,9 31,0 37,2 46,5 55,8 65,1 74,4 30,0 33,3 40,0 50,0 60,0 70,0 80,0 33,6 37,4 44,9 56,1 67,3 78,5 89,7 39,3 43,7 52,4 65,5 78,6 91,7 105,0 32,7 36,3 43,6 54,5 65,4 76,3 87,2

Switching (30/60s) 125A 500A 13,8 14,8 20,6 22,9 27,5 34,4 41,3 48,1 55,0 22,2 24,7 29,6 37,0 44,4 51,8 59,2

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage Arresters for other voltages are available on request.

20

MV Surge Arresters for Indoor Applications RSTI-SA

Screened, separable surge arresters for gas-insulated switchgear system RSTI-SA type Modern gas-insulated switchgear connected to combined underground and overhead distribution systems are sensitive to effects like transient voltage doubling. An arrester installed right at the cable end will clamp the voltage to a level which does not put the switchgear at risk. The RSTI surge arrester, together with the Raychem RSTI connection system for gas-insulated switchgear, facilities at hermetically sealed integration of the arrester and the cable termination to be connected to a switchgear. Compact design and easy installation are the special features of this product line.

290 110 101

~78

~76

57

Generic technical data: RSTI-SA series Rated discharge current (8/20s): Operating duty impulse withstand current (4/10s): Long duration current impulse (1000s): 10 second temporary overvoltage (UTOV/UC): Short Circuit current Is

10 kA 12-41 kV Uc 10 kA 100 kA 212 A 1,42 20 kA

Protective Characteristics RSTI Uc kV

Ur kV

U residual in kV when tested the following impulse waveforms Lightning Steep lightning Switching impulse Height (8/20s) (1/20s) (30/60s) mm 5kA 10kA 20 kA 10kA 125 A 500 A 39,1 58,2 78,2 117,3 127,1 133,6 41,5 62,2 83,0 124,5 134,9 141,8 45,7 68,5 91,4 114,2 137,1 148,5 156,1 43,9 68,5 78,8 114,2 137,1 148,5 156,1 31,5 47,3 63,1 78,9 94,7 102,5 107,8 32,4 48,7 64,9 81,1 97,4 105,5 110,9 285 400 400 520 520 520 520

Weight kg 4,4 4,6 4,8 5,0 5,1 5,2 5,3

RSTI-CC-66SA1210 RSTI-CC-66SA1810 RSTI-CC-66SA2410 RSTI-CC-66SA3010 RSTI-CC-66SA3610 RSTI-CC-66SA3910 RSTI-CC-66SA4110

12 18 24 30 36 39 41

15,0 22,5 30,0 37,5 45,0 48,8 51,3

97,7 103,7

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage Arresters for other voltages are available on request.

21

MV Surge Arresters for Indoor Applications SPA

In air-spaced insulated switchgear systems SPA type A compact arrester with high mechanical strength. Even there are no sheds the housing material is fully track resistant and able to provide flashover resistance in damp indoor conditions. The SPA type arrester is also available with a thick-wall insulated integrated line lead, which allows to considerably reduce the clearances between the arresters and to the earth. This line lead is available in lengths of 250mm, 500mm and 750mm. This SPA-I type arrester is the ideal solution when retrofitting compact switchgears with arresters.

Generic technical data: SPA-xx series Rated discharge current (8/20s):

Air-spaced switchgear with SPA-I arresters. 6-36 kV Uc 10 kA Class 1 100 kA 400 A 1,25 16 kA 2,6 kJ/kV Uc 5,3 kJ/kV Uc

SPA SPA / SPA-I SPA-06 SPA-09 SPA-10 SPA-12 SPA-15 SPA-18 SPA-21 SPA-24 SPA-27 SPA-30 SPA-33

SPA-I Height L (mm) 138 168 177 200 299 329 361 393 491 522 554 586

Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temporary overvoltage (UTOV/UC) High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy line discharge impulse high current impulse

Mechanical strength data Cantilever Tensile Torque Protective Characteristics SPA / SPA-I Uc kV 200 Nm 1000 N 58 Nm

SPA-36

Ur kV

SPA-06 SPA-09 SPA-10 SPA-12 SPA-15 SPA-18 SPA-21 SPA-24 SPA-27 SPA-30 SPA-33 SPA-36

6 9 10 12 15 18 21 24 27 30 33 36

7,5 11,0 12,5 15,0 18,0 22,0 26,0 30,0 33,0 37,0 41,0 45,0

Ures in kV when tested to impulse waveforms Lightning Steep lightning (8/20s) (1/20s) 5kA 10kA 20kA 40kA 10kA 18,6 20,0 22,4 26,2 21,8 27,9 31,0 37,2 46,5 55,8 65,1 74,4 83,7 93,0 102,0 112,0 30,0 33,3 40,0 50,0 60,0 70,0 80,0 90,0 100,0 110,0 120,0 33,6 37,4 44,9 56,1 67,3 78,5 89,7 101,0 112,0 123,0 135,0 39,3 43,7 52,4 65,5 78,6 91,7 105,0 118,0 131,0 144,0 157,0 32,7 36,3 43,6 54,5 65,4 76,3 87,2 98,1 109,0 120,0 131,0

Switching (30/60s) 125A 500A 13,8 14,8 20,6 22,9 27,5 34,4 41,3 48,1 55,0 61,9 68,8 75,6 82,5 22,2 24,7 29,6 37,0 44,4 51,8 59,2 66,6 74,0 81,4 88,8

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage Arresters for other voltages are available on request. 22

MV Surge Arresters for Indoor Applications MPA

For motor-connection boxes MPA type Design for the specific requirements of electric motors. A robust, non-tracking housing plus the high energy handling capabilities of the Tyco Electronics arrester family make it the ideal choice for the designer.
L

Generic technical data: MPA-xx series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temporary overvoltage (UTOV/UC) High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy line discharge impulse high current impulse 2-12 kV Uc 10 kA Class 1 100 kA 400 A 1,25 16 kA 2,6 kJ/kV Uc 5,3 kJ/kV Uc

MPA MPA-02 MPA-03 MPA-04 MPA-06 MPA-07 MPA-09 MPA-10 MPA-12

Height L (mm) 101 107 114 138 148 168 177 200

Mechanical strength data Cantilever Tensile Torque 200 Nm 1000 N 58 Nm

Protective Characteristics MPA Uc kV

Ur kV

MPA-02 MPA-03 MPA-04 MPA-06 MPA-07 MPA-09 MPA-10 MPA-12

2 3 4 6 7 9 10 12

2,5 3,7 5,0 7,5 8,7 11,0 12,5 15,0

Ures in kV when tested to impulse waveforms Lightning Steep lightning (8/20s) (1/20s) 5kA 10kA 20kA 40kA 10kA 6,2 6,7 7,5 8,7 7,3 9,3 12,4 18,6 21,7 27,9 31,0 37,2 10,0 13,3 20,0 23,3 30,0 33,3 40,0 11,2 15,0 22,4 26,2 33,6 37,4 44,9 13,1 17,5 26,2 30,6 39,3 43,7 52,4 10,9 14,5 21,8 25,4 32,7 36,3 43,6

Switching (30/60s) 125A 500A 4,6 4,9 6,9 9,2 13,8 16,0 20,6 22,9 27,5 7,4 9,9 14,8 17,3 22,2 24,7 29,6

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage Arresters for other voltages are available on request.

23

Tyco Electronics MV Surge Arresters with external spark-gaps

Protection system MORE for mediumvoltage transformer overhead lines This type of surge arresters is designed to protect the insulator assembly at transformers from the lightning overvoltages. It is connected parallel to the insulator assembly. It is defined as a device that contains a non-linear metal oxide resistor element in its arrester body (MORE) and an external series gap to isolate the MORE from the system.

The protection is accomplished by raising the spark-over level of the external series gap to a level that isolates the arrester from power frequency overvoltages and from the worst case switching overvoltages expected on the line which it is applied. The external series gap acts as an isolating apparatus in the event of arrester body failure.

Without MORE Lightning protection with arcing horns. In case of lightning overvoltage, the system is out of function based on the present voltage.

The pictures below show different constructions of the MORE system.

With MORE Lightning protection with the MORE arrester. The MORE will be disconnect and the system will be in function.

10 kV System
100 kV Sparkover Voltage

20 kV System
150 kV Sparkover Voltage 100 kV

50 kV Residual Voltage 50 kV Residual Voltage

10

20

10

20

24

Tyco Electronics MV Surge Arresters for covered conductors CLX

Protection system CLX for mediumvoltage covered conductor overhead lines An absolute must when covered conductor systems are used. CLX prevents covered conductors from melting and falling down to earth when lightning strikes generate overvoltages in overhead lines. CLX guides the lightning discharge current ground, prevents the insulator from flashing over and stops the high energy of the power frequency follow-on current. On top of this, CLX protected overhead lines will have almost no power supply interruptions during storms.

This makes it attractive also for bare conductor distribution systems. Even in case of accidental bridging CLX will not cause a phase-to-ground fault. The CLX device contains a Metal Oxide Resistive Element and an external series gap to isolate the Metal Oxide Resistive Element from the system. The CLX device is installed next to the line / post insulators and can be adapted to the system. The series gap will be realized by different brackets, electrodes and connectors. We offer engineering support to optimize the use of CLX.

Covered conductor system protected by CLX

Generic technical data: CLX-xx series Rated discharge current (8/20s): Operating duty impulse withstand current (4/10s): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions line discharge impulse high current impulse Ambient temperature: 12-42 kV Uc 5 kA 65 kA 16 kA 1,5 kJ/kV Uc 3,6 kJ/kV Uc - 60C to + 60C

Mechanical strength data Cantilever Torque 150 Nm 45 Nm

Protective Characteristics CLX

Um kV

CLX-12NA CLX-15NA CLX-24NA CLX-36NA CLX-42NA

12,0 15,0 24,0 36,0 42,0

Ures in kV when tested to impulse waveforms Lightning Lightning Impulse Sparkover Voltage (8/20s) Standard Steep 2,5kA 5kA 10kA 20kA (1/20s) (1000kV/s) 30,0 32,0 35,0 40,0 80,0 140,0 31,0 48,0 77,0 86,0 33,0 51,0 83,0 91,0 36,0 57,0 91,0 136,0 41,0 63,0 103,0 153,0 100,0 140,0 190,0 230,0 175,0 250,0 400,0 450,0

Um: Max. System Voltage; Ures: Residual Voltage / Sparkover Voltage

Metal Oxide Resistive Elements Houstng Parameter CLX Power Flash Creepage voltage over length withstand, distance wet (kV) (mm) (mm) CLX-12NA 31 182 375 CLX-15NA CLX-24NA CLX-36NA CLX-42NA 31 50 50 81 182 283 283 465 375 715 715 1090

Height L

Weight
>100 47

(mm) 191 191 286 286 477

(kg) 1,20 1,20 1,90 1,90 3,10

191

Typical setup for Um 12 kV 25

Tyco Electronics MV Surge Arresters for cable sheath protection system CPA

High-voltage cable sheath protection system CPA Designed to the specific requirements in cable sheath protection. A robust, non tracking housing plus the high energy handling capabilities of the Raychem arrester family make it the ideal choice for the designer.
L

CPA arresters installed in a cubicle to protect HV cable sheath cross bonds

Generic technical data: CPA-xx series Rated discharge current (8/20s): Line discharge class according to IEC 60099-4 Operating duty impulse withstand current (4/10s): Long duration current impulse (2000s): 10 second temporary overvoltage (UTOV/UC) High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy line discharge impulse high current impulse 1-7 kV Uc 10 kA Class 1 100 kA 400 A 1,25 16 kA 2,6 kJ/kV Uc 5,3 kJ/kV Uc

CPA CPA-01 CPA-02 CPA-03 CPA-04 CPA-05 CPA-06 CPA-07

Height L (mm) 94 101 107 114 123 138 148

Mechanical strength data Cantilever Tensile Torque 200 Nm 1000 N 58 Nm

Protective Characteristics CPA Uc kV

Ur kV

CPA-01 CPA-02 CPA-03 CPA-04 CPA-05 CPA-06 CPA-07

1 2 3 4 5 6 7

1,2 2,5 3,7 5,0 6,2 7,5 8,7

Ures in kV when tested to impulse waveforms Lightning Steep lightning (8/20s) (1/20s) 5kA 10kA 20kA 40kA 10kA 3,1 3,3 3,7 4,4 3,6 6,2 9,3 12,4 15,5 18,6 21,7 6,7 10,0 13,3 16,7 20,0 23,3 7,7 11,2 15,0 18,7 22,4 26,2 8,7 13,1 17,5 21,8 26,2 30,6 7,3 10,9 14,5 18,2 21,8 25,4

Switching (30/60s) 125A 500A 2,3 2,5 4,6 6,9 9,2 11,5 13,8 16,0 4,9 7,4 9,9 12,3 14,8 17,3

Uc: Continous Voltage; Ur: Rated Voltage; Ures: Residual Voltage 26

MV Surge Arresters for D.C. and A.C. Railway Applications

For D.C. Applications Type HE 60 These DC-type surge arresters are particularly suitable for protection against overvoltages caused by lightning and switching in both DC railway systems and network up to 4.5kV. The low residual voltage and high-energy capacity of the metal-oxide varistors ensure safety and reliability even under the most extreme conditions. Thanks to its rugged, compact design, the arrester is capable of withstanding extreme mechanical stress (vibrations, shocks, pressure, torsion). HE 60 surge arresters have been tested in compliance with the CENELEC standard for surge arresters in DC networks for railways EN 50123-5, 2003. Further tests have been carried out to examine the sealing properties of the arrester and its resistance to mechanical stress and fire.

For A.C. Applications Type HDA-M / OCP For installation on locomotive and other rolling stock Tyco Electronics offers special design solutions. Please contact your sales representative for further information. For application on outdoor catenary please select the appropriate outdoor surge arrester documented on page 6, 8 and 10.

Generic technical data: HE60MCxx series Rated discharge current (8/20s): Operating duty impulse withstand current (4/10s): 10 second temporary overvoltage (UTOV/US): High current short circuit: (pre-failing method) (Safe non-shattering failure mode) Energy Service conditions 1 high current impulse Ambient temperature: 1-6 kV Ur 10 kA 100 kA 1,31 25 kA 2,3 kJ/kV Ur - 60C to + 60C

Protective Characteristics HE60MC Us Ur kV kV

Ures in kV when tested to impulse waveforms Lightning (8/20s) 100A 200A 1,8 1,8 2,7 3,6 4,1 5,4 7,2 9,1 12,7 2,8 3,7 4,3 5,7 7,5 9,3 13,2

HE60MC07 HE60MC10 HE60MC15 HE60MC18 HE60MC20 HE60MC30 HE60MC39 HE60MC45

0,7 1,0 1,5 1,8 2,0 3,0 3,9 4,5

1,0 1,4 2,0 2,1 2,8 4,0 4,9 6,0

1kA 2,0 3,0 4,0 4,6 6,1 8,1 10,2 14,3

2,5kA 2,1 3,2 4,3 4,9 6,5 8,6 10,9 15,2

5kA 2,2 3,3 4,5 5,2 6,7 9,0 11,9 16,4

10kA 2,4 3,7 4,9 5,6 7,4 9,9 12,4 17,4

20kA 2,7 4,0 5,4 6,2 8,1 10,9 13,6 19,1

Steep current (1/20s) 10kA 2,7 4,0 5,4 6,2 8,1 14,8 13,7 19,2

Switching current (30/60s) 125A 500A 1,8 1,9 2,7 3,6 4,2 5,5 10,6 9,3 13,0 2,9 3,8 4,4 5,8 11,4 9,7 13,6

Us: System Voltage; Ur: Rated Voltage; Ures: Residual Voltage Standard Housing Parameter HE60MC Impulse Power voltage frequency 1.2/50s voltage withstand, wet (kV) (kV) HE60MCxx 82 60 Flash over distance Creepage length Weight

(mm) 130

(mm) 246

(kg) 3,60

Accessories for Line Terminal, Ground Terminal and Mounting are available on request. 27

Metal Oxide Arresters for Applications in Low Voltage Networks LVA and MOSIPO

Type LVA Low voltage surge arresters are installed at transitions of LV-ABC lines to underground or service cables and to transformers. The metal-oxide varistors incorporated in the surge arrester reliably protects the insulation of the network and the connected equipment from all kind of surges. In case of overload, e.g. by lightning strike in vicinity of arrester, an integrated disconnector disconnects the arrester from the network. A bundle of installation accessories like insulated line leads and mounting brackets are available to meet the individual requirements. Two different types of arresters are available which are both tested according to Class II of IEC 61643-1 + Amd. 1 / EN 61643-11.

Type LVA Following features are applicable for both arrester types: Gapless metal-oxide surge arrester Flame retardant and UV resistant High current impulse 4/10s (IEC 60099-4): 100 kA Tested to exceed ambient temperature of -40 up to +70 C Watertightness tested at 6 kV for 30 min in a waterbath Integrated 1 m ground lead as standard accessory

Type BOW MOSIPO Differences between the both arrester types are the following: BOW-MOSIPO 15: Silicone housing At disconnection the ground lead will be separated from the housing and the disconnection event is clearly visible LVA: Sturdy, weatherproof polymer housing At disconnection the ground lead remains in position and it is easy to spot coloured plate hanging down from the arrester

Technical Data Continuous Voltage UC Residual Voltage at IN (8/20s Impulse) Nominal discharge current (IN) Maximum discharge current (Imax)

BOW-MOSIPO 15-275 275 V 1,80 kV 15 kA 40 kA

BOW-MOSIPO 15-440 440 V 2,28 kV 15 kA 40 kA

LVA-280B 280 V 1,20 kV 10 kA 40 kA

LVA-440B 440 V 1,80 kV 10 kA 40 kA

Ordering description for surge arrester and accessories

BOW-MOSIPO 15/ LVA

280 440 280 440

BL

150

300

A
Line connection Threaded bolt M8x16

260

F
Insulated flexible line lead to fit to piercing connectors

Clamp for bare Insulated right angle conductors adapter to fit to 16mm2 up to 120mm2 piercing connectors

Insulated adapter with bird cap to fit to transformators

28

Tyco Electronicss total commitment to quality

Even the best technology must be backed up by a thorough and consistent quality assurance program. At Tyco Electronics, we subject every product to an extensive quality control regimes which includes the following procedures: At every production stage, beginning with the raw materials and continuing through to the packaged product, the QC lab tests all physical and electrical characteristics which can influence quality. By means of lot numbers the Quality Assurance Program ensures traceability backwards all the way to the details of the compound batch test reports. We carry out requalification testing on a regular basis.

Quality assurance at Tyco Electronics is not a static, but rather a constantly improving process directed towards our goals: complete customer satisfaction. The Tyco Electronics Energy Division arrester manufacturing sites are accredited to ISO 9001 and ISO 14001. Our vendor routine tests and internal incoming inspection confirm performance of all critical components used in the assembly of our arresters

Automized routine test facility for Metal-Oxide Surge Arresters in the manufacturing area

29

Offices in CIS Countries

Representative Offices in CIS Countries

RUSSIA
127287 Moscow 2 Khutorskaya Str. 38A, Bld.8 Tel.: +7 495-790 790 2-200 Fax: +7 495-721 1892 196084 Saint-Petersburg Tsvetochnaya str. 25 Office 212 Tel./Fax: +7 812-313 0959 620142 Ekaterinburg Bolshakova Str. 70 Office 501 Tel./Fax: +7 343-297 1829 420021 Kazan Parizhskoy Kommuny Str. 14 Tel.Fax: +7 843-293 9470 680000 Khabarovsk Murieva-Amurskogo str. 44 Office 313 Tel./Fax: +7 421-245 1154 630054 Novosibirsk 3 per. Krasheninnikova, 3 Office 104 Tel.: +7 383-355 9992 Fax: +7 383-355 9991 344023 Rostov-na-Donu Lenina str. 118a Tel./Fax: +7 863-293 0739 443096 Samara Michurina str. 52 Office 315 Tel./Fax: +7 846-266 9514 394016 Voronezh Moskovsky Prospect 53 Office 202 Tel./Fax: +7 473-239 2277 EN-RU@tycoelectronics.com

UKRAINE
04050 Kiev 13, Pimonenko Str., 7A section / 11 Tel.: +380 44-206 2266 Fax: +380 44-206 2268 83023 Donetsk 16 A Labutenko Str., office 123 Tel./Fax: +380 62-332 3644 EN-UA@tycoelectronics.com

ARMENIA
YERENERGO CJSC 375001 Yerevan 11 Toumanyan str., office 7 Tel.: +374 10-542 122 Fax: +374 10-582 060 info@yerenergo.am

MONGOLIA
Ulziikhishig BAYASGALAN Ulaanbaatar Sukhe-baatar District 10 horoo, bld. 29, office 3 Tel./Fax: + 976 701-355-89 bayasgalan_tyco@yahoo.com

BELARUS
Vyacheslav DEMICHEV 220050 Minsk K. Marksa 21-39 Tel./Fax: +375 17-226 0333 cerber@parom.com

TAJIKISTAN
Akmal KARIMOV 734024 Dushanbe Nazarshoev street 143 Tel.: +992 37-881 3106 Fax: + 992 37-227 1659 akmal80@bk.ru

KAZAKHSTAN
050004 Almaty Naurizbay batyr str. 17 Office 215 Tel.: +7 7272-44 5875 Fax: +7 7272-44 5877 010000 Astana Barayev str. 16 Block B, office 5 Tel./Fax: +7 717-259 2756 EN-KZ@tycoelectronics.com

GEORGIA
Nodar MGEBRISHVILI 0179 Tbilisi Radiani st. 19 Tel.: +995 99-562 791 Fax: +995 32-230 392 nomgeb@wanex.net

TURKMENISTAN
Timur SULTANMURADOV 744007 Ashgabat A. Berdieva 25-307 Tel./Fax: +99 312-326 826 sultantimur77@rambler.ru

AZERBAIJAN
1014, Baku Fizuly street, 49 SKS Plaza 5th floor, office 5 Tel: +994 12 597 0049 EN-AZ@tycoelectronics.com

KYRGYZSTAN
is served by Tyco Electronics Raychem GmbH representative in Uzbekistan

UZBEKISTAN
Iskander KAMILOV 100000 Tashkent Merzo-Ulugbeksky D-t 24 Akmal Ikramov st. Tel.: +998 71-252 6256 Fax: +998 71-237 5251 iskom@gs.uz

MOLDOVA
Igor BEIU 2068 Chiinu Str. Miron Costin, nr.19, bl.5, apt.63 Tel./Fax: +373 22-322 155 linte@mcc.md

While Tyco Electronics and its affiliates referenced herein have made every reasonable effort to ensure the accuracy of the information contained in this catalog, Tyco Electronics cannot assure that this information is error free. For this reason, Tyco Electronics does not make any representation or offer any guarantee that such information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information at any time. Tyco Electronics expressly disclaims any implied warranty regarding the information contained herein, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics' only obligations are those stated in Tyco Electronics Standard Terms and Conditions of Sale. Tyco Electronics will in no case be liable for any incidental, indirect or consequential damages arising from or in connection with, including, but not limited to, the sale, resale, use or misuse of its products. Users should rely on their own judgement to evaluate the suitability of a product for a certain purpose and test each product for its intended application. In case of any potential ambiguities or questions, please dont hesitate to contact us for clarification. Bowthorpe EMP, Raychem, TE (logo) and Tyco Electronics are trademarks of the Tyco Electronics group of companies and its licensors.

Tyco Electronics Raychem GmbH Energy Division Finsinger Feld 1 85521 Ottobrunn/Munich, Germany Phone: +49-89-6089-435 Fax: +49-89-6089-741 http://energy.tycoelectronics.com

Tyco Electronics EPP 0533 CIS 9/09