3313

PARKING BRAKE PARKING BRAKE ASSY

PARKING BRAKE ASSY

COMPONENTS

Parking Brake Shoe HoldDown Spring Pin

Parking Brake Shoe Lever LH

Parking Brake Shoe Assy LH No.2

Parking Brake Shoe HoldDown Spring Pin Tension Spring Tension Spring Parking Brake Shoe HoldDown Compression Spring Parking Brake Shoe Adjusting Screw Set

Parking Brake Shoe Strut LH Parking Brake Shoe Assy LH No.1

Tension Spring Parking Brake Shoe HoldDown Compression Spring

Rear Disc Brake Caliper Assy LH Rear Disc

NVm (kgfVcm, ftVlbf) : Specified torque High temperature grease

AVENSIS REPAIR MANUAL (RM1018E)

3314
PARKING BRAKE PARKING BRAKE ASSY
330C801

OVERHAUL
HINT: Overhaul the RH side by the same procedures as those of the LH side. 1. REMOVE REAR WHEEL 2. DISCONNECT REAR DISC BRAKE CALIPER ASSY LH (See page 3031)

3. REMOVE REAR DISC (a) Release the parking brake, and remove the rear disc. HINT: S Put matchmarks on the disc and the axle hub. S If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns freely.
Contract
F45710

4. (a)

INSPECT BRAKE DISC INSIDE DIAMETER Using a brake drum gauge or equivalent, measure the inside diameter of the disc. Standard inside diameter: 173 mm (6.81 in.) Maximum inside diameter: 174 mm (6.85 in.)

F06409

5. (a) (b)

REMOVE PARKING BRAKE ADJUSTER KIT Using needlenose pliers, remove the shoe upper side 2 tension springs. Remove the parking brake shoe strut LH.

G22379

6. (a) (b)

REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET Using needlenose pliers, remove the anchor side tension spring. Remove the shoe adjusting screw set.

C88314

G22380

AVENSIS REPAIR MANUAL (RM1018E)

3315
PARKING BRAKE PARKING BRAKE ASSY

7. (a)
SST

REMOVE PARKING BRAKE SHOE KIT Using SST, remove the parking brake shoe holddown compression spring, parking brake shoe holddown spring pin and parking brake shoe assy LH No.1. SST 0971800010

C88315

F45077

(b)
SST

(c)

Using SST, remove the parking brake shoe holddown compression spring and parking brake shoe holddown spring pin. SST 0971800010 Disconnect the parking brake shoe assy LH No.2 from the parking brake shoe lever LH, and remove the parking brake shoe LH No.2.

F44822

8. (a)

INSPECT PARKING BRAKE SHOE LINING THICKNESS Using a ruler, measure the thickness of the shoe lining. Standard thickness: 3.5 mm (0.138 in.) Minimum thickness: 1.0 mm (0.039 in.)

R00311

9.

INSPECT BRAKE DISC AND PARKING BRAKE SHOE LINING FOR PROPER CONTACT (a) Apply chalk to the inside surface of the disc, then grind down the brake shoe lining to fit. If the contact between the brake disc and the shoe lining is improper, repair it using a brake shoe grinder or replace the brake shoe assembly.
BR0828

10. (a)

REMOVE PARKING BRAKE SHOE LEVER LH Using needlenose pliers, disconnect the parking brake cable assy No.3 and remove the parking brake shoe lever LH.

F42661

AVENSIS REPAIR MANUAL (RM1018E)

3316
PARKING BRAKE PARKING BRAKE ASSY

11. (a)

APPLY HIGH TEMPERATURE GREASE Apply the high temperature grease to the shoe attached surface of backing plate.

C95250

F44709

12. (a)

INSTALL PARKING BRAKE SHOE LEVER LH Using needlenose pliers, connect the parking brake cable assy No.3 to the parking brake shoe lever LH.

F42661

13. (a)

INSTALL PARKING BRAKE SHOE KIT Apply the high temperature grease to the contact part of the parking brake shoe and parking brake shoe lever.

C80704

(b)
SST

Using SST, install the parking brake shoe LH No.2 with the parking brake shoe holddown compression spring and parking brake shoe holddown spring pin. SST 0971800010

F44822

(c)
SST

Using SST, install the parking brake shoe LH No.1 with the parking brake shoe holddown compression spring and parking brake shoe holddown spring pin. SST 0971800010

C88315

F44705

AVENSIS REPAIR MANUAL (RM1018E)

3317
PARKING BRAKE PARKING BRAKE ASSY

14. (a) (b)

INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET Apply the high temperature grease to the adjusting bolt and support piece. Install the parking brake shoe adjusting screw set LH.

C80705

(c)

Using needlenose pliers, install the tension spring.

C88314

G22380

15. (a) (b)

INSTALL PARKING BRAKE ADJUSTER KIT Apply the high temperature grease to the contact part of the shoe strut and tension spring. Install the parking brake shoe strut LH.

C80706

(c)

Using needlenose pliers, install the upper side 2 tension springs.

HINT: Install the 2 tension spring securely to the grooves of the shoe strut.

G22379

AVENSIS REPAIR MANUAL (RM1018E)

3318
PARKING BRAKE PARKING BRAKE ASSY

16. CHECK PARKING BRAKE INSTALLATION (a) Check that each part is installed properly. NOTICE: There should be no oil or grease on the friction surface of the shoe lining and disc.

LH

RH

Front

Front

F44823

17.

INSTALL REAR DISC

Expand

18. (a) (b) (c)

Contract

F44708

(d) (e)

ADJUST PARKING BRAKE SHOE CLEARANCE Temporarily install the hub nuts. Remove the hole plug, and turn the adjuster and expand the shoes until the disc locks. Contract the shoe adjuster until the disc can rotate smoothly. Standard : Return 8 notches Check that there is no brake drag. Install the hole plug.

19. (a) 20.

CONNECT REAR DISC BRAKE CALIPER ASSY LH Install the rear disc brake caliper with the 2 bolts. Torque: 47 NVm (475 kgfVcm, 34 ftVlbf) INSTALL REAR WHEEL Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)

AVENSIS REPAIR MANUAL (RM1018E)

3319
PARKING BRAKE PARKING BRAKE ASSY

21. (a) (b) (c) (d) 22. 23.

SETTLING PARKING BRAKE SHOES AND DISC Drive the vehicle at about 50km/h (31 mph) on a safe,level and dry road. With the parking brake release button pushed in, pull on the lever with 98 N (10kgf, 19.8 lbf) of force. Drive the vehicle for about 400 meters (0.25 mile) in this condition. Repeat this procedure 2 or 3 times. INSPECT PARKING BRAKE LEVER TRAVEL (See page 332) ADJUST PARKING BRAKE LEVER TRAVEL (See page 332)

AVENSIS REPAIR MANUAL (RM1018E)

336
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.1

PARKING BRAKE CABLE ASSY NO.1

COMPONENTS
Console Panel SubAssy Lower A/T Transaxle type:

A/T Transaxle Console Panel SubAssy Upper Floor Shift Shift Lever Knob SubAssy Console Box Assy RR M/T Transaxle Lock Nut M/T Transaxle type: Console Panel SubAssy Upper
5.0 (51, 44 in.Vlbf)

M/T Transaxle

Adjusting Nut
13 (127, 9)

Equalizer
43 (440, 32)

Parking Brake Switch Connector Parking Brake Lever Subassy Parking Brake Cable Assy No.1 Gasoline Engine Type: Front Floor Heat Insulator No.1 Gasoline Engine Type: Front Floor Heat Insulator No.2
5.5 (56, 49 in.Vlbf) 5.5 (56, 49 in.Vlbf)

Exhaust Pipe Support

Exhaust Pipe Assy Front

Front Floor Panel Brace

43 (440, 32)

Exhaust Pipe Support

NVm (kgfVcm, ftVlbf) : Specified torque

AVENSIS REPAIR MANUAL (RM1018E)

337
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.1
3306B03

REPLACEMENT
1. 2. 3. 4. 5. 6. REMOVE SHIFT LEVER KNOB SUBASSY (M/T TRANSAXLE) (See page 4111) REMOVE CONSOLE PANEL SUBASSY UPPER (See page 7111) REMOVE CONSOLE PANEL SUBASSY LOWER (See page 7111) REMOVE CONSOLE BOX ASSY RR (See page 7111) REMOVE PARKING BRAKE LEVER SUBASSY (See page 334) REMOVE EXHAUST PIPE ASSY FRONT 1ZZFE/3ZZFE ENGINE TYPE: See page 152 1AZFE/1AZFSE ENGINE TYPE: See page 157

7. (a)

REMOVE FRONT FLOOR HEAT INSULATOR NO.1 (GASOLINE ENGINE TYPE) Remove the 3 nuts and front floor insulator No.1.

F44815

8. (a)

REMOVE FRONT FLOOR HEAT INSULATOR NO.2 (GASOLINE ENGINE TYPE) Remove the 2 nuts and front floor insulator No.2.

F44816

9. (a) 10. (a)

REMOVE PARKING BRAKE CABLE ASSY NO.1 Disconnect the parking brake cable assy No.1 from the equalizer and remove the parking brake cable assy No.1. INSTALL PARKING BRAKE CABLE ASSY NO.1 Connect the parking brake cable assy No.1 to the equalizer and install the parking brake cable assy No.1.

AVENSIS REPAIR MANUAL (RM1018E)

338
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.1

11. (a)

INSTALL FRONT FLOOR HEAT INSULATOR NO.2 (GASOLINE ENGINE TYPE) Install the front floor insulator No.2 with the 2 nuts. Torque: 5.5 NVm (56 kgfVcm, 49 in.Vlbf)

F44816

12. (a)

.INSTALL FRONT FLOOR HEAT INSULATOR NO.1 (GASOLINE ENGINE TYPE) Install the front floor insulator No.1 with the 3 nuts. Torque: 5.5 NVm (56 kgfVcm, 49 in.Vlbf)

F44815

13.

14. 15. 16.

INSTALL EXHAUST PIPE ASSY FRONT 1ZZFE/3ZZFE ENGINE TYPE: See page 152 1AZFE/1AZFSE ENGINE TYPE: See page 157 INSTALL PARKING BRAKE LEVER SUBASSY (See page 334) INSPECT PARKING BRAKE LEVER TRAVEL (See page 332) ADJUST PARKING BRAKE LEVER TRAVEL (See page 332)

AVENSIS REPAIR MANUAL (RM1018E)

339
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.3

PARKING BRAKE CABLE ASSY NO.3

COMPONENTS

Parking Brake Cable No.2 Clamp

Parking Brake Cable Assy No.2

5.0 (51, 44 in.Vlbf)

Parking Brake Cable Assy No.3

Equalizer Cable Retainer

Parking Brake Cable No.2 Clamp

5.5 (56, 49 in.Vlbf)

Fuel Tank Protector No.1

Gasoline Engine Type: Front Floor Heat Insulator No.2 Gasoline Engine Type: Front Floor Heat Insulator No.1

43 (440, 32)

5.5 (56, 49 in.Vlbf)

Exhaust Pipe Assy Front Exhaust Pipe Support

43 (440, 32)

Front Floor Panel Brace

30 (302, 21)

Exhaust Pipe Support NVm (kgfVcm, ftVlbf) : Specified torque

43 (440, 32)

F44817

AVENSIS REPAIR MANUAL (RM1018E)

3310
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.3
330C701

REPLACEMENT
HINT: For parking brake cable assy No.2, perform the same procedure to the RH side. 1. REMOVE REAR WHEEL 2. DISCONNECT REAR DISC BRAKE CALIPER ASSY LH (See page 3031) 3. REMOVE REAR DISC(See page 3314) 4. REMOVE PARKING BRAKE ADJUSTER KIT (See page 3314) 5. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET(See page 3314) 6. REMOVE PARKING BRAKE SHOE KIT (See page 3314) SST 0971800010

7. (a)

DISCONNECT PARKING BRAKE CABLE ASSY NO.3 Using needlenose pliers, and disconnect the parking brake cable assy No.3 from the backing plate.

F44818

8.

9. 10.

REMOVE EXHAUST PIPE ASSY FRONT 1ZZFE/3ZZFE ENGINE TYPE: See page 152 1AZFE/1AZFSE ENGINE TYPE: See page 157 REMOVE FRONT FLOOR HEAT INSULATOR NO.1 (GASOLINE ENGINE TYPE) (See page 337) REMOVE FRONT FLOOR HEAT INSULATOR NO.2 (GASOLINE ENGINE TYPE) (See page 337)

11. (a) (b) (c)

REMOVE PARKING BRAKE CABLE ASSY NO.3 Remove the 3 nuts and fuel tank protector No.1 (When replacing parking brake cable assy No.2). Remove the 4 bolts and cable retainer from the body. Disconnect the parking brake cable assy No.3 from the equalizer, and remove the parking brake cable assy No.3.

AVENSIS REPAIR MANUAL (RM1018E)

3311
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.3

12. (a) (b)

INSTALL PARKING BRAKE CABLE ASSY NO.3 Connect the parking brake cable assy No.3 to the equalizer. Install the parking brake cable assy No.3 with the 4 bolts. Torque: 5.0 NVm (55 kgfVcm, 48 in.Vlbf)

F44819

(c)

Install the fuel tank protector No.1 and 3 nuts (When replacing parking brake cable assy No.2). Torque: 5.5 NVm (56 kgfVcm, 49 in.Vlbf)

13. 14. 15.

INSTALL FRONT FLOOR HEAT INSULATOR NO.2 (GASOLINE ENGINE TYPE) (See page 337) INSTALL FRONT FLOOR HEAT INSULATOR NO.1 (GASOLINE ENGINE TYPE) (See page 337) INSTALL EXHAUST PIPE ASSY FRONT 1ZZFE/3ZZFE ENGINE TYPE: See page 152 1AZFE/1AZFSE ENGINE TYPE: See page 157

16. (a)

CONNECT PARKING BRAKE CABLE ASSY NO.3 Connect the parking brake cable assy No.3 to the backing plate.

F44820

AVENSIS REPAIR MANUAL (RM1018E)

3312
PARKING BRAKE PARKING BRAKE CABLE ASSY NO.3

17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29.

APPLY HIGH TEMPERATURE GREASE (See page 3314) INSTALL PARKING BRAKE SHOE LEVER LH (See page 3314) INSTALL PARKING BRAKE SHOE KIT (See page 3314) SST 0971800010 INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET (See page 3314) INSTALL PARKING BRAKE ADJUSTER KIT (See page 3314) INSTALL REAR DISC CONNECT REAR DISC BRAKE CALIPER ASSY LH(See page 3031) ADJUST PARKING BRAKE SHOE CLEARANCE(See page 3314) INSTALL REAR WHEEL Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf) SETTLING PARKING BRAKE SHOES AND DISC (See page 3314) INSPECT PARKING BRAKE LEVER TRAVEL (See page 332) ADJUST PARKING BRAKE LEVER TRAVEL (See page 332) CHECK EXHAUST LEAKAGE

AVENSIS REPAIR MANUAL (RM1018E)

333
PARKING BRAKE PARKING BRAKE LEVER SUBASSY

PARKING BRAKE LEVER SUBASSY

COMPONENTS
A/T TRANSAXLE:

Console Panel SubAssy Lower Console Panel SubAssy Upper Floor Shift Shift Lever Knob SubAssy

A/T Transaxle

M/T Transaxle M/T TRANSAXLE: Console Panel SubAssy Upper

Console Box Assy RR M/T Transaxle Lock Nut

Adjusting Nut
13 (127, 9)

Parking Brake Switch Assy

Parking Brake Switch Connector Parking BrakeLever Subassy

Screw Parking BrakeCable No.1

NVm (kgfVcm, ftVlbf) : Specified torque

AVENSIS REPAIR MANUAL (RM1018E)

334
PARKING BRAKE PARKING BRAKE LEVER SUBASSY
330C601

REPLACEMENT
1. 2. 3. 4. REMOVE FLOOR SHIFT SHIFT LEVER KNOB SUBASSY (M/T TRANSAXLE) (See page 4111) REMOVE CONSOLE PANEL SUBASSY UPPER (See page 7111) REMOVE CONSOLE PANEL SUBASSY LOWER (See page 7111) REMOVE CONSOLE BOX ASSY RR (See page 7111)

5. (a) (b)

REMOVE PARKING BRAKE LEVER SUBASSY Disconnect the parking brake switch connector from the parking brake switch. Remove the lock nut and adjusting nut from the parking brake cable assy No.1.

F44810

(c)

Remove the 2 bolts.

F41838

(d)

(e)

Using a screwdriver, raise the pick on the parking brake lever, and remove the parking brake cable assy No.1 from the parking brake lever. Remove the parking brake lever from the body.

F44811

6. (a)

REMOVE PARKING BRAKE SWITCH ASSY Remove the screw and parking brake switch.

F44812

AVENSIS REPAIR MANUAL (RM1018E)

335
PARKING BRAKE PARKING BRAKE LEVER SUBASSY

7. (a)

INSTALL PARKING BRAKE SWITCH ASSY Install the parking brake switch to the parking brake lever with the screw.

F44812

8. (a)

(b)

INSTALL PARKING BRAKE LEVER SUBASSY Install the parking brake cable assy No.1 to the parking brake lever, temporally tighten the adjusting nut and lock nut. Using a screwdriver, fix the parking brake cable No.1 to the pick.

F44813

(c)

Install the parking brake lever with the 2 bolts. Torque: 13 NVm (127 kgfVcm, 9 ftVlbf)

F41838

(d)

Install the parking brake switch connector to the parking brake switch.

F44810

9. 10.

INSPECT PARKING BRAKE LEVER TRAVEL (See page 332) ADJUST PARKING BRAKE LEVER TRAVEL (See page 332)

AVENSIS REPAIR MANUAL (RM1018E)

331
PARKING BRAKE PARKING BRAKE SYSTEM

PARKING BRAKE SYSTEM

PROBLEM SYMPTOMS TABLE

AVENSIS REPAIR MANUAL (RM1018E)

332
PARKING BRAKE PARKING BRAKE SYSTEM
3300F07

ADJUSTMENT
1. 2. 3. 4. (a) REMOVE REAR WHEEL ADJUST PARKING BRAKE SHOE CLEARANCE (See page 3314) INSTALL REAR WHEEL Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf) INSPECT PARKING BRAKE LEVER TRAVEL Pull the parking brake lever all the way up, and count the number of clicks. Parking brake lever travel: 6 9 clicks at 196 N (20 kgf, 44.1 lbf) 5. ADJUST PARKING BRAKE LEVER TRAVEL (a) Remove the console box assy RR. (See page 7111)

(b)
Adjusting Nut

(c)
Lock Nut

(d)

Loosen the lock nut and turn the adjusting nut until the lever travel turns correct. Tighten the lock nut. Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf) Install the console box assy RR. (See page 7111)

F44808

AVENSIS REPAIR MANUAL (RM1018E)