A SEMINAR REPORT On SUMMER TRAINING Undergone at

AIRPORT AUTHORITY OF INDIA, JAIPUR

Submitted By ABHA GUPTA
Department of Electronics & Communication Engineering

ASIANS INSTITUTE OF TECHNOLOGY

BHURTIA, TONK

DEPARTMENT
of ELECTRONICS & COMMUNICATION ENGEERING CERTIFICATE

This is to certify that a seminar report on summer training taken at AIRPORT AUTHORITY OF INDIA (Jaipur Airport) is submitted by ABHA GUPTA, student of 4th year (VII semester) in Electronics and Communication Engineering of Rajasthan Technical University, Kota during the academic year 2012-2013. The report has been found satisfactory and is approved for submission.

Assistant Prof. EC

II

ACKNOWLEDGEMENT

We cannot achieve anything worthwhile in the field of technical education unless or until the theoretical education acquired in the classroom is effectively wedded to its practical approach that is taking place in the modern industries and research institutes. My sincere thanks to Mr.Kamlesh Kumar, Manager(electronics),our training co-coordinator for providing the proper guidance and continuous encouragement for making this training successful. I also express my deep gratitude to Mr. P.S.Verma, Jt.G.M.(Comm.),Airports Authority of India, Jaipur Airport for providing me this golden opportunity to attend the Industrial training. It is a matter of great pleasure privilege for me to present this report of 30 days on the basis of practical knowledge gained by me during practical training at Airport Authority of India, Jaipur Rajasthan during session 2010-2011. I attribute heartiest thanks to all CNS faculty members of their ample guidance during my training period and at last my cordial thanks to my batch mates and friends for their cooperation.

(ABHA GUPTA)

III

PAGE INDEX
Topic Page No.
01 03

ABSTRACT 1. BRIEF DISCRIPTION OF JAIPUR AIRPORT 1.1 1.2 1.3 Introduction Functions of AAI General Information

2. CNS DEPARTMENT 2.1 2.2 Role of CNS Department Classification of CNS Facilities 08

3. COMMUNICATION SYSTEM 3.1 3.2 3.3 3.4 3.5 Introduction Transmitter Channel Reciever Modulation 3.5.1 3.5.2 3.6 Transmitter Modulation Space Modulation

Communication System 3.6.1 3.6.2 3.6.3 3.6.4 3.6.5 Air traffic Control Walkie-Talkie Voice Communication Control System Tape Recorder Digital Airport Terminal Information System

IV

3.7

Frequency Bands and Its Uses in Communication

4. NAVIGATIONAL AIDS.... 4.1 4.2 4.3 4.4 4.5 5. Navigation ILS DME DVOR ILS Parameters and Components EQUIPMENTS...

16

SECURITY 5.1 5.2 5.3 5.4 5.5 5.6

27

X-BIS Walk Through Metal Detector HHMD ETD FIDS PA System 37

6. IT SECTION... 6.1 6.2 6.3 6.4 Functions of IT Department Basics Networking Network Topologies

7. CONCLUSION 8. BIBLIOGRAPHY...

44 45

TABLE INDEX

Table

Page No.

1.1 1.2 1.3 1.4

Table 2.1 Table 3.1 Table 3.2 Table 4.1

Classification of CNS Facilities Radio Waves Classificaion Frequency Bands Used in Communication ILS Parameters and Components

06 15 15 26

VI

FIGURE INDEX
Figure Page No.

3.1 3.2 3.3 3.4 4.1 4.2 4.3 4.4 4.5 5.1 5.2 5.3 5.4 5.5 5.6 6.1 6.2 6.3 6.4 6.5 6.6 6.7

Block Diagram of Radio Transmitter Block Diagram of AM Superhetrodyne Receiver Voice Communication Control System Tape Recorder System Emission Pattern Location of ILS Components DME System DVOR System DVOR antennas X-Ray Production X-BIS System WTMD Eight Overlapping Detecting Zones ETD FIDS Block Diagram of Networks LAN WAN Bus Network Star Network Ring Network Mesh Network

09 10 13 14 18

VII

VIII

ABSTRACT
Airports Authority of India (AAI) was constituted by an Act of Parliament and came into being on 1st April 1995 by merging erstwhile National Airports Authority and International Airports Authority of India. The merger brought into existence a single Organization entrusted with the responsibility of creating, upgrading, maintaining and managing civil aviation infrastructure both on the ground and air space in the country. AAI manages 125 airports, which include 11 International Airport, 08 Customs Airports, 81 Domestic Aairports and 27 Civil Enclaves at Defence airfields. AAI provides air navigation services over 2.8 million square nautical miles of air space.

PASSENGER FACILITIES

The main functions of AAI inter-alia include construction, modification & management of passenger terminals, development & management of cargo terminals, development & maintenance of apron infrastructure including runways, parallel taxiways, apron etc., Provision of Communication, Navigation and Surveillance which includes provision of DVOR / DME, ILS, ATC radars, visual aids etc., provision of air traffic services, provision of passenger facilities and related amenities at its terminals thereby ensuring safe and secure operations of aircraft, passenger and cargo in the country.

AIR NAVIGATION SERVICES In tune with global approach to modernization of Air Navigation infrastructure for seamless navigation across state and regional boundaries, AAI has been going ahead with its plans for transition to satellite based Communication, Navigation, Surveillance and Air Traffic Management.

SECURITY The continuing security environment has brought into focus the need for strengthening security of vital installations. There was thus an urgent need to revamp the security at airports not only to thwart any misadventure but also to restore confidence of traveling public in the security of air travel as a whole, which was shaken after 9/11 tragedy..

AERODROME FACILITIES In Airports Authority of India, the basic approach to planning of airport facilities has been adopted to create capacity ahead of demand in our efforts. Towards implementation of this strategy, a number of projects for extension and strengthening of runway, taxi track and aprons at different airports has been taken up.

HRD TRAINING A large pool of trained and highly skilled manpower is one of the major assets of Airports Authority of India. AAI has a number of training establishments, viz. NIAMAR in Delhi, CATC in Allahabad, Fire Training Centres at Delhi & Kolkata for in-house training of its engineers, Air Traffic Controllers, Rescue & Fire Fighting personnel etc.

IT IMPLEMENTATION Information Technology holds the key to operational and managerial efficiency, transparency and employee productivity. AAI website with domain name www.airportsindia.org.in or www.aai.aero is a popular website giving a host of information about the organization besides domestic and international flight schedules and such other information of interest to the public in general and passengers in particular

CHAPTER 1
2

BRIEF DISCRIPTION OF JAIPUR AIRPORT

1.1 INTRODUCTION
Jaipur is the Capital city of Rajasthan and is also called the PINK CITY. (Zero mile point). It is well connected with other major cities by Rail/Road and air. Distance of Jaipur Airport from Railway Station is12 Km. Area: Population: 3, 42,237Sq Km 2.6 Million as per 2001 census

Jaipur Runway strip 15/33 with one terminal office and two Hanger was constructed by Maharaja Mansingh II in 1932 named as Sanganer Airport. Dakota Aircraft was used for domestic and International flight from Jaipur to Karachi/Lahore. New Runway with orientation 09/27 of length 9000 feet has been constructed and de-used Runway 15/33 is being used for parking the Aircrafts. The salient features of the New Terminal Building (Terminal-2) are: Glass and steel structure with passenger friendly facilities such as: (a) Most modern security system (b) Centrally air-conditioning system. Passenger Boarding Bridge (Aerobridges), (c) Two glass aerobridges with visual docking system. (d) On Line Baggage conveyer system. (e) Escalator and Glass Lifts. (f) Large Duty Free Shoe Area. (g) Twin-Level connection segregating arrival and Departure area. (h) Underground pedestrian link to/from car parking area to Concourse. (i) Peak Pax-500 (250 Departure, 250 Arrival)

The Airlines operating at this airport are: (a) (b)

International: Indian , Air Arabia, & Air India Domestic : Indian, Jet Airways, Indigo, Kingfisher, Go Air, Spice Jet.

All domestic flights are to be operated from new terminal building (T-2) and all International flights are to be operated from the existing old terminal building (T-1).

1.2

FUNCTIONS OF AAI
To control and manage the entire Indian airspace (excluding the special user airspace) extending beyond the territorial limits of the country, as accepted by ICAO. To Design, Construct, Operate and Maintain International Airports, Domestic Airports, Civil Enclaves at Defence Airports. Development and Management of Cargo Terminals at Airports. Provision of Passenger Facilities and Information System at the Passenger Terminals at airports. Expansion and strengthening of operation area viz. Runways, Aprons, Taxiway, etc Provision of visual aids. Provision of Communication and Navigational aids viz. ILS, DVOR, DME, Radar, etc.

1.3

GENERAL INFORMATION
Jaipur Airport, Jaipur Civil Aerodrome OIC, AAI, Jaipur Airport Jaipur - 302011 24 hours P.S. Verma, Jt.GM (Com) Northern Region New Delhi

1. Name of Airport 2. Type of Airport 3. Address 4. Operational Hours 5. Name & Designation of Officer-in-Charge 6. Region 7. RHQ

CHAPTER 2 CNS DEPARTMENT

2.1 ROLE OF CNS DEPARTMENT
1. To provide uninterrupted services of Communication, Navigation and Surveillance (CNS) facilities for the smooth and safe movement of aircraft (over flying, departing & landing) in accordance with ICAO standards and recommended practices. 2. To maintain Security Equipments namely X-Ray Baggage systems (XBIS), Hand Held Metal Detectors (HHMD) and Door Frame Metal Detectors (DFMD). 3. To provide and maintain inter-unit communication facility i.e. Electronic Private Automatic Exchange Board (EPABX) 4. To maintain the Computer systems including peripherals like printers, UPS etc. provided in various sections connected as standalone as well as on Local Area Network (LAN). 5. To maintain the passenger facilitation systems like Public Address (PA) system, Car Hailing System and Flight Information Display System (FIDS). 6. To maintain and operate Automatic Message Switching system (AMSS) used for exchange of messages over Aeronautical Fixed Telecommunication Network (AFTN). 7. To provide Communication Briefing to pilots by compiling NOTAM received from other International NOF. 8. To maintain and operate Fax machine. 9. To co-ordinate with telephone service providers for provision and smooth functioning of auto telephones/ hotlines/ data circuits.

2.2 CLASSIFICATION OF CNS FACILITIES

COMMUNICATION EQUIPMNET NAME OF THE MAKE FREQUENCY EQUIPMENT VHF AM Sets Transmitters OTE DT-100 125.25 126.6 50W

POWER

Receivers

OTE DR-100

125.25 126.6

PAE 5610 PAE BT6M VHF AM DS-Radio Transreceivers JORTON I-COM DVTR FIDS Digital Clock DSCN LAN/WAN EPABX Marathon IDDS SOLARI Bihar Comm. VIASAT Cisco Tele Coral Panasonic

125.25

NA

24 Chnl NA NA NA NA NA NA NA NA NA

161.825Mhz Mobile Radio (FM) MOTOROLA For CISF Communication VERTEX 166.525Mhz (BASE STATION) Standard For AAI -MOTOROLA SIMCO) Mobile Radio (FM) 161.825Mhz Communication Vertex 166.525Mhz (Hand Held Sets) Standard KENWOOD

10W

----

NAVIGATION EQUIPMENT NAME OF THE MAKE EQUIPMENT DVOR (JJP) HP DME(JJP) (Collocated DVOR) with GCEL-755 THALES Airsys-435 NORMAC7013 NORMAC7033

FREQUENCY 112.9 Mhz. 1100 1163 Mhz 109.9 Mhz 333.8 Mhz 997 1060 Mhz 295 Khz

POWER 100W 1 KW 5W 100W 50W

LOCALIZER (IJIP) GLIDE PATH

LP DME (IJIP THALES Collocated with Airsys -415 GP) Locator Outer SAC 100

SECURITY EQUIPMENTS NAME OF THE EQUIPMENT Departure Lounge 100100V Security Hold Area 6040i Departure Lounge 100100V Security Hold Area 6040i Explosive Trace Detectors Smith 500 DT DFMD CCTV PA SYSTEM MAKE Heimann (Ger)

Heimann (Ger) Heimann (Ger) Heimann (Ger) Smith IONSCAN500DT (Singapore) METOR-200 CEIA INFINOVA PHILIPS BOSCH

CHAPTER 3 COMMUNICATION SYSTEM

3.1 INTRODUCTION
Communication is the process of sending, receiving and processing of information by electrical means. It started with wire telegraphy in 1840 followed by wire telephony and subsequently by radio/wireless communication. The introduction of satellites and fiber optics has made communication more widespread and effective with an increasing emphasis on computer based digital data communication. In Radio communication, for transmission information/message are first converted into electrical signals then modulated with a carrier signal of high frequency, amplified up to a required level, converted into electromagnetic waves and radiated in the

space, with the help of antenna. For reception these electromagnetic waves received by the antenna, converted into electrical signals, amplified, detected and reproduced in the original form of information/message with the help of speaker.

3.2 TRANSMITTER
Unless the message arriving from the information source is electrical in nature, it will be unsuitable for immediate transmission. Even then, a lot of work must be done to make such a message suitable. This may be demonstrated in single-sideband modulation, where it is necessary to convert the incoming sound signals into electrical variations, to restrict the range of the audio frequencies and then to compress their amplitude range. All this is done before any modulation. In wire telephony no processing may be required, but in long-distance communications, transmitter is required to process, and possibly encode, the incoming information so as to make it suitable for transmission and subsequent reception. Eventually, in a transmitter, the information modulates the carrier, i.e., is superimposed on a high-frequency sine wave. The actual method of modulation varies from one system to another. Modulation may be high level or low level, (in VHF we use low level modulation) and the system itself may be amplitude modulation, frequency modulation, pulse modulation or any variation or combination of these, depending on the requirements. Figure 1.1 shows a lowlevel amplitude-modulated transmitter type. Antenna
CRYSTAL OSC & AMP MODULATOR & DRIVER PA RF OUTPUT POWER AMP

AUDIO IN

AUDIO AMPLIFIER

Figure 3.1

Block diagram of radio transmitter

3.3 CHANNEL
The acoustic channel (i.e., shouting!) is not used for long-distance communications and neither was the visual channel until the advent of the laser. "Communications," in this context, will be restricted to radio, wire and fiber optic channels. Also, it should be noted that the term channel is often used to refer to the frequency range allocated to a particular service or transmission, such as a television channel (the allowable carrier bandwidth with modulation). It is inevitable that the signal will deteriorate during the process of transmission and reception as a result of some distortion in the system, or because of the introduction of noise, which is unwanted energy, usually of random character, present in a transmission system, due to a variety of causes. Since noise will be received together with the signal, it places a limitation on the transmission system as a whole. When noise is severe, it may mask a given signal so much that the signal becomes unintelligible and therefore useless. Noise may interfere with signal at any point in a communications system, but it will have its greatest effect when the signal is weakest. This means that noise in the channel or at the input to the receiver is the most noticeable.

3.4 RECEIVER
There are a great variety of receivers in communications systems, since the exact form of a particular receiver is influenced by a great many requirements. Among the more important requirements are the modulation system used, the operating frequency and its range and the type of display required, which in turn depends on the destination of the intelligence received. Most receivers do conform broadly to the super heterodyne type, as does the simple receiver whose block diagram is shown in Figure. Antenna

RF Stage

MIXE R

Intermediate Frequency Amplifier

Demodulator

Audio Voltage and Power amplifiers

Local Oscillator

10

Speaker

Figure 3.2

Block diagram of AM super heterodyne receiver

Receivers run the whole range of complexity from a very simple crystal receiver, with headphones, to a far more complex radar receiver, with its involved antenna arrangements and visual display system, which will be expanded upon in Chapter 6. Whatever the receiver, its most important function is demodulation (and sometimes also decoding). Both these processes are the reverse of the corresponding transmitter modulation processes. As stated initially, the purpose of a receiver and the form of its output influence its construction as much as the type of modulation system used. The output of a receiver may be fed to a loudspeaker, video display unit, teletypewriter, various radar displays, television picture tube, pen recorder or computer: In each instance different arrangements must be made, each affecting the receiver design. Note that the transmitter and receiver must be in agreement with the modulation and coding methods used (and also timing or synchronization in some systems).

3.5 MODULATION
3.5.1 TRANSMITTER (OR EQUIPMENT) MODULATION.
Transmitter modulation is one in which, the carrier and total sideband components are combined in a fixed phase relationship in the equipment (say transmitter) and the combined wave follow a common RF path from the transmitting antenna through space to the receiver ensuring no introduction of phase difference between the carrier and the TSB on its way. It is obvious that the mixing (multiplication) of the carrier and the modulating signal has to be taken

11

place to produce the TSB within the equipment only, before combining (adding) it with carrier within or outside the equipment.

3.5.2 SPACE MODULATION

Another type of amplitude modulation process may be required to be used in many places like Navaids where the combination (addition) of sideband only (SBO comprising one or more TSB(s)) and the carrier with or without the transmitter modulated sidebands takes place in space. Note that both of the SBO or carrier with sidebands (CSB) are transmitter modulated but when all the required signals out of these three namely SBO, CSB or carrier are not radiated from the same antenna the complete modulation process will be realized rather the composite modulated waveform will be formed at the receiving point by the process of addition of all the carriers and all the sidebands (TSBs). The process of achieving the complete modulation process by the process of addition of carriers and sidebands (TSBs) at the receiving point in space is called the Space Modulation which means only that modulation process is achieved or completed in space rather than in equipment itself but not at all that space is modulated.

3.6 COMMUNICATION SYSTEMS

3.6.1 AIR TRAFFIC CONTROL (ATC)
Air traffic control (ATC) is a service provided by ground-based controllers who direct aircraft on the ground and in the air. The primary purpose of ATC systems worldwide is to separate aircraft to prevent collisions, to organize and expedite the flow of traffic, and to provide information and other support for pilots when able. [1] In some countries, ATC may also play a security or defense role (as in the United States), or be run entirely by the military (as in Brazil).

12

Preventing collisions is referred to as separation, which is a term used to prevent aircraft from coming too close to each other by use of lateral, vertical and longitudinal separation minima; many aircraft now have collision avoidance systems installed to act as a backup to ATC observation and instructions. In addition to its primary function, the ATC can provide additional services such as providing information to pilots, weather and navigation information and NOTAMs (NOtices to AirMen). Depending on the type of flight and the class of airspace, ATC may issue instructions that pilots are required to follow, or merely flight information to assist pilots operating in the airspace. In all cases, however, the pilot in command has final responsibility for the safety of the flight, and may deviate from ATC instructions in an emergency.

3.6.2 WALKIE -TALKIE

A walkie-talkie, or handie talkie, (more formally known as a handheld transceiver) is a handheld, portable, two-way radio transceiver. Its development during the Second World War has been variously credited to Donald L. Hings, radio engineer Alfred J. Gross, and engineering teams at Motorola. Similar designs were created for other armed forces, and after the war, walkie-talkies spread to public safety and eventually commercial and jobsite work. Major characteristics include a half-duplex channel (only one radio transmits at a time, though any number can listen) and a "push-to-talk" (P.T.T) switch that starts transmission. Typical walkietalkies resemble a telephone handset, possibly slightly larger but still a single unit, with an antenna sticking out of the top. Where a phone's earpiece is only loud enough to be heard by the user, a walkie-talkie's built-in speaker can be heard by the user and those in the user's immediate vicinity. Hand-held transceivers may be used to communicate between each other.Its frequency at Jaipur Airport is 166.2 Mhz.

3.6.3 VOICE COMMUNICATION CONTROL SYSTEM

The Voice Communication Control System (VCCS) is a Voice Switch and Control System for networking an airport VHF communication system. It is an electronic switching system, which

13

controls the complex flow of speech data between air traffic controllers on ground and aircraft. The system has been designed using Complementary Metal Oxide Semiconductor (CMOS) digital circuits and is very easy to operate. The VCCS is based on a modular architecture. The heart of the system is a Central Switching Unit (CSU) in which the data inputs from various controller workstations are separately processed. A multi-bus data link connects the CSU with each controller workstation.

Figure 3.3 Voice Communication Control System

3.6.4 TAPE RECORDER

The purpose of tape recorder is to store the Sound by recording of sound either by Disc Recording, Film Recording or Magnetic Recording. In our Department, we are using Magnetic Recording to record the communications/speech between Air (Aircraft) to Ground, Ground to Ground, telephones, Intercoms etc. For any miss happening or any other reason, the conversations of past period can be checked to find out the root cause so that in future such types of mistakes can be avoided.

14

Figure 3.4 Tape Recorder System

3.6.5 DIGITAL AIRPORT TERMINAL INFORMATION SYSTEM (DATIS)

Digital Airport Terminal Information System (DATIS) is an intelligent announcing system used for Automatic Terminal Information Service (ATIS) for the automatic provision of current, routine information (weather, runway used etc.) to arriving and departing aircraft throughout 24 hrs or a specific portion thereof. The System is Completely solid-state, without any moving parts. The design is based around advanced digital techniques viz., PCM digitization, high density Dynamic RAM Storage and microprocessor control. This ensures reproduction of recorded speech with high quality and reliability. Storage capacity normally supplied is for 4 minutes Announcement, and as the system design is modular, it can be increased by simply adding extra memory. The system is configured with fully duplicated modules, automatic switch-over mechanism and Uninterrupted Power Supply to ensure Continuous System availability.

15

3.7 FREQUENCY COMMUNICATION

BANDS

AND

ITS

USES

IN

Table 3.1 Radio Waves Classification BAND NAME FREQUENCY BAND Ultra Low Frequency (ULF) 3Hz 30 Hz Very Low Frequency (VLF) 3 kHz - 30 kHz Low Frequency (LF) 30 kHz - 300 kHz Medium Frequency (MF) 300 kHz - 3 MHz High Frequency (HF) 3 MHz - 30 MHz Very High Frequency (VHF) 30 MHz - 300 MHz Ultra High Frequency (UHF) 300 MHz -3 GHz Super High Frequency (SHF) 3 GHz - 30 GHz Extra High Frequency (EHF) 30 GHz - 300 GHz Infrared Frequency 3 THz- 30 THz Table 3.2 Frequencies band uses in communication NAME OF THE EQUIPMENT NDB HF Localizer VOR VHF Glide Path DME UHF LINK RADAR FREQUENCY BAND 200 450 KHz 3 30 MHz 108 112 MHz 108 117.975 MHz 117.975 137 MHz 328 336 MHz 960 1215 MHz 0.3 2.7 GHz 0.3 12 GHz USES Locator, Homing & En-route Ground to Ground/Air Com. Instrument Landing System Terminal, Homing & En-route Ground to Air Comm. Instrument Landing System Measurement of Distance Remote Control, Monitoring Surveillance

CHAPTER 4

NAVIGATIONAL AIDS

4.1 NAVIGATION

16

Navigation is the process of reading, and controlling the movement of a craft or vehicle from one place to another. It is also the term of art used for the specialized knowledge used by navigators to perform navigation tasks. The word navigate is derived from the Latin "navigate", which is the command "sail". Radio Navigation is based on the use of Radio Transmitter, Radio Receiver and propagation of electromagnetic waves to find navigational parameter such as direction, distance, position of the aircraft etc. According to service range the radio navigational aids are broadly classified into three categories 1. Long Range. 2. Medium Range. 3. Short range. 1. Long Range navigational aids Operate in very low frequency and low frequency, i.e. 10KHz, 50-100KHz and 100200KHz respectively. LORAN and OMEGA falls in this category.

2. Medium range navigational aids It operates in the LF or MF band of frequency . It gives the range of 150-250 nautical miles. NDB (Non Directional Beacons) falls in this category.

3. Short-range navigational aids

These aids operate in and above VHF bands. The coverage is dependent upon line of sight propagation. VHF, ILS, DME, VOR and RADAR are some widely used short-range aids.

17

4.2 ILS
An instrument landing system (ILS) is a ground-based instrument approach system that provides precision guidance to an aircraft approaching and landing on a runway, using a combination of radio signals and, in many cases, high-intensity lighting arrays to enable a safe landing during instrument meteorological conditions (IMC), such as low ceilings or reduced visibility due to fog, rain, or blowing snow. Instrument approach procedure charts (or approach plates) are published for each ILS approach, providing pilots with the needed information to fly an ILS approach during instrument flight rules (IFR) operations, including the radio frequencies used by the ILS components or navaids and the minimum visibility requirements prescribed for the specific approach. Radio-navigation aids must keep a certain degree of accuracy (set by international standards of CAST/ICAO); to assure this is the case, flight inspection organizations periodically check critical parameters with properly equipped aircraft to calibrate and certify ILS precision.

4.2.1 PRINCIPLE OF OPERATION

An ILS consists of two independent sub-systems, one providing lateral guidance (localizer), the other vertical guidance (glide slope or glide path) to aircraft approaching a runway. Aircraft guidance is provided by the ILS receivers in the aircraft by performing a modulation depth comparison.

18

Figure 4.1 The Emission Patterns Of The Localizer And Glide Slope Signals.
A localizer (LOC, or LLZ until ICAO designated LOC as the official acronym) antenna array is normally located beyond the departure end of the runway and generally consists of several pairs of directional antennas. Two signals are transmitted on one out of 40 ILS channels between the carrier frequency range 108.10 MHz and 111.95 MHz (with the 100 kHz digit always odd, so 108.10, 108.15, 108.30, and so on are LOC frequencies but 108.20, 108.25, 108.40, and so on are not). One is modulated at 90 Hz, the other at 150 Hz and these are transmitted from separate but co-located antennas. Each antenna transmits a narrow beam, one slightly to the left of the runway centerline, the other to the right. The localizer receiver on the aircraft measures the difference in the depth of modulation (DDM) of the 90 Hz and 150 Hz signals. For the localizer, the depth of modulation for each of the modulating frequencies is 20 percent. The difference between the two signals varies depending on the position of the approaching aircraft from the centerline. If there is a predominance of either 90 Hz or 150 Hz modulation, the aircraft is off the centerline. In the cockpit, the needle on the horizontal situation indicator (HSI, the instrument

19

part of the ILS), or course deviation indicator (CDI), will show that the aircraft needs to fly left or right to correct the error to fly down the center of the runway. If the DDM is zero, the aircraft is on the centerline of the localizer coinciding with the physical runway centerline. A glide slope (GS) or glide path (GP) antenna array is sited to one side of the runway touchdown zone. The GP signal is transmitted on a carrier frequency between 329.15 and 335 MHz using a technique similar to that of the localizer. The centerline of the glide slope signal is arranged to define a glide slope of approximately 3 above horizontal (ground level). The beam is 1.4 deep; 0.7 below the glide slope centerline and 0.7 above the glide slope centerline. These signals are displayed on an indicator in the instrument panel. This instrument is generally called the Omni-bearing indicator or nav indicator. The pilot controls the aircraft so that the indications on the instrument (i.e., the course deviation indicator) remain centered on the display. This ensures the aircraft is following the ILS centerline (i.e., it provides lateral guidance). Vertical guidance, shown on the instrument by the glide slope indicator, aids the pilot in reaching the runway at the proper touchdown point.

4.2.2 COMPONENTS OF ILS

4.2.2.1 LOCALIZER The localizer provides runway centerline guidance to aircraft. In some cases a localizer is at an angle to the runway usually due to obstructions around the airport. It is then called a Localizer Type Directional Aid. The Localizer is placed about 1,000 feet on the far end of the approached runway. Its useful volume extends to 18 NM for the path up to 10 degrees either side of the course. For an angle of 35 degrees either side of the course the useful volume of the Localizer extends up to 10 NM. Localizer uses the frequency range 108-112MHz. frequency at Jaipur Airport is 109.9MHz. Its

20

4.2.2.2. GLIDE PATH The function of the Glide Path unit is to provide, within its coverage limits, an inclined plane aligned with the glide path of the runway for providing elevation guidance to landing aircraft. The Glide Path gives the information indicating the aircrafts position relative to the required angle of descent. The MARRY antenna is used for it. Frequency range for Glide path is 328336MHz. Its frequency at Jaipur Airport is 333.8MHz. Covering range for Glide Path is 10NM. The Glide Path unit is made up of a building, the transmitter equipment, the radiating antennas and monitor antennas mounted on towers. The antennas and the building are located about 300 feet to one side of the runway center line at a distance of about 1,000 feet from the approach end of the runway.

4.2.2.3. INNER MARKER A marker basically gives the distance from the runway, to the aircraft. It is about 1000 feet from the runway threshold. At inner marker the aircraft should be about 50 feet above from the runway centerline.

4.2.2.4

MIDDLE MARKER

It is about 3500 feet from the runway threshold. At middle marker the aircraft should be about 225 feet above from the runway centerline.

21

4.2.2.5. OUTER MARKER It is about 7000 feet from the runway threshold. At outer marker the aircraft should be about 2700 feet above from the runway centerline.

Figure 4.2 Typical Locations of ILS Components

22

4.3 DME
Distance measuring equipment (DME) provides pilots with a slant range measurement of distance to the runway in nautical miles. DMEs are augmenting or replacing markers in many installations. The DME provides more accurate and continuous monitoring of correct progress on the ILS glide slope to the pilot, and does not require an installation outside the airport boundary. When used in conjunction with an ILS, the DME is often sited midway between the reciprocal runway thresholds with the internal delay modified so that one unit can provide distance information to either runway threshold.

4.3.1 OPERATION
The operating principle of DME system is based on the RADAR principle means the time required for a radio pulse signal to travel to a given point and return. DME is Secondary RADAR with the location of the Transponder and Interrogator reversed. The airborne transmitter repeatedly initiates a process of sending out very short, very widely spaced interrogation pulses. These are picked up by the ground transponder receiver whose output triggers the associated transmitter into sending out reply pulses on a different channel. The airborne receiver receives these replies. Timing circuit automatically measures the round-trip travel time, or interval between interrogation and reply pulses, and converts this time into electrical signal, which operate the distance indicator.

23

Distance calculation- A radio pulse takes around 12.36 microseconds to travel one nautical mile to and from, this is also referred to as a RADAR-Mile. The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit. DME frequency range Allotted: 960MHz to 1215MHz. Critically used: 962 MHz to 1213MHz. The variation in time spacing of the pulse pairs of the aircraft interrogation is termed as Pulse Jittering. Thus the variation in time spacing of the pulse pair is unique to each aircraft, and permits the aircraft to select the replies to its particular interrogations.

Figure 4.3 DME System

24

4.4 DVOR
The Doppler Very high frequency Omni Range is a ground based, radio aircraft navigation aid, transmitting an Omni-directional signal that enables and to determine its bearing relative to the location of the beacon.

4.4.1 BASICS
It works on the principle of phase comparison of two 30 Hz signals. Frequency range for DVOR is 112-118MHz. Range of covering is 200NM (for medium range aid)

4.4.2 ANTENNA
Antenna used for DVOR is called modified Alford slot antenna. An antenna system,

comprising a ring of 48 sideband antennas and a central carrier antenna, mounted on a suitable ground plane. The counter poise is uses as a ground plain. It works as a perfect conductor. Diameter is set at a distance of 44.0 feet or13.4 meter. This arrangement produces peak frequency deviation. DVOR is phase sensitive equipment thus it uses the Horizontal Polarization, as to minimize the effect of noise. 4.4.2.1 OPERATION Amplitude Modulating the carrier frequency signal by a 30Hz-modulating signal produces the DVOR reference signal. The modulating carrier is radiated from the central Omni-directional

25

antenna. The phase of 30Hz AM is therefore constant irrespective of direction, hence termed 30Hz reference. The DVOR variable signal is produced by the space modulation of carrier signal by the amplitude of the frequency modulated sideband signals. The sideband signals (fc+9960Hz) and (fc-9960Hz) are radiated diametrically in a ring of antennas and are commutated around the ring at a 30Hz rate. The distant observer therefore, sees a Doppler frequency shift of these sideband frequencies varying at 30 Hz with a maximum deviation determined by the diameter of the ring. The Doppler VOR beacons also transmit VOICE and CODE identification information to the aircraft. This information amplitude modulates the RF carrier and is radiated Omni directionally from the central antenna, along with the 30 Hz AM reference signal. In the aircraft receiver the complex VHF signal is first envelope detected to obtain the 30 Hz AM signal and the 9960 Hz sub carrier. The sub carrier contains the variable signal. This signal is fed to two sets of filters to separate the 30Hz and 9960Hz sub carrier. One of the filter produces a 30Hz output the Reference signal whereas the other produces the 30Hz Variable signal. The 9960 Hz sub carrier is FM demodulated to obtain the FM variable signal. The relative phase difference between the two 30 Hz is then measured. The bearing information is converted into a visual indication for the pilot.

26

Figure 5.4 DVOR System

Figure 5.5 DVOR Antennas

4.5 ILS PARAMETERS AND COMPONENTS

ILS PARAMETER a. Azimuth Approach Guidance b. Elevation Approach Guidance c. Fixed Distances from Threshold d. Range from touch down point ILS COMPONENT Provided by Localizer Provided by Glide Path Provided by Marker Beacons Provided by DME

27

CHAPTER 5 SECURITY EQUIPMENTS

The main security equipments are1. X-BIS 2. WTMD 3. HHMD 4. ETD 5. FIDS 6. PA System

5.1. X-BIS
The luggage carried by the passengers is checked by using the X-Ray Baggage Inspection System.

5.1.1. NATURE OF X-RAYS

X-rays are electromagnetic waves whose wavelengths range from about (0.1 to 100)x 10-10 m. They are produced when rapidly moving electrons strike a solid target and their kinetic energy is converted into radiation. The wavelength of the emitted radiation depends on the energy of the electrons.

5.1.2 PRODUCTION OF X-RAYS

There are two principal mechanisms by which x-rays are produced.The first mechanism involves the rapid deceleration of a high-speed electron as it enters the electrical field of a nucleus. During this process the electron is deflected and emits a photon of x-radiation. This

28

type of x-ray is often referred to as bremsstrahlung or "braking radiation". For a given source of electrons, a continuous spectrum of bremsstrahlung will be produced up to the maximum energy of the electrons. The second mechanism by which x-rays are produced is through transitions of electrons between atomic orbits. Such transitions involve the movement of electrons from outer orbits to vacancies within inner orbits. In making such transitions, electrons emit photons of x-radiation with discrete energies given by the differences in energy states at the beginning and the end of the transition. Because such x-rays are distinctive for the particular element and transition, they are called characteristic x-rays. A tungsten filament is heated to 20000C to emit electrons. A very high voltage is placed across the electrodes in the two ends of the tube and the tube is evacuated to a low pressure, about 1/1 000 mm of mercury. These electrons are accelerated in an electric field toward a target, which could be tungsten also (or more likely copper or molybdenum for analytical systems). The interaction of electrons in the target results in the emission of a continuous bremsstrahlung spectrum along with characteristic x-rays from the particular target material. Unlike diagnostic x-ray equipment, which primarily utilize the bremsstrahlung x-rays, analytical x-ray systems make use of the characteristic x-rays.

FIGURE 5.1 X-Rays Production 5.1.3 SPECIFICATIONS

Tunnel Dimensions

620(w)*418(h)[mm]

29

Max. Object size Conveyor Speed Max. Conveyor load even distributed

615(w)*410(h)[mm] 0.2m/sec. 160kg.

5.1.4 OPERATION
When the start key is pressed from the keyboard then the command goes to the microprocessor, then to the interface board. The interface board starts the motor hence conveyor belt starts running. But at this time X-Rays doesnt generate. The X-BIS contain the emergency stop switches from the safety point of view. When baggage is run on the conveyor belt and passes through the light barriers then interruption occurs. The microprocessor reads the interrupt through interface board. Microprocessor again gives the command to the X-Ray generator to generate X-Rays through the interface board. X-Rays falls on the baggage some absorb and rest passes through it. The X-Rays now converts into the voltage by a transducer. Now a VGA (Voltage Graphic Adopter) converts the input voltage signal into the output graphic image on the monitor. At the monitor slice-by-slice screening is achieved.

30

FIGURE 5.2 X-BIS System

The X-BIS shows the different color patterns according to the material inside the baggage, such as: 1. Organic 2. Inorganic 3. Metal : : : Orange color Green Blue

5.2 WTMD
The metal objects which passengers a carrying with them is detected during passenger screening by Walk Through Metal Detector. The system is used for weapons detection as well as passenger screening. Main components are1. Transmitter panel (TX) 2. Receiver panel (RX) 3. Cross piece. 4. Remote control unit. 5. Electronics unit

31

Figure 5.3 WTMD

Almost all airport metal detectors are based on pulse induction (PI). Typical PI systems use a coil of wire on one side of the arch as the transmitter and receiver. This technology sends powerful, short bursts (pulses) of current through the coil of wire. Each pulse generates a brief magnetic field. When the pulse ends, the magnetic field reverses polarity and collapses very suddenly, resulting in a sharp electrical spike. This spike lasts a few microseconds (millionths of a second) and causes another current to run through the coil. This subsequent current is called the reflected pulse and lasts only about 30 microseconds. Another pulse is then sent and the process repeats. A typical PI-based metal detector sends about 100 pulses per second, but the number can vary greatly based on the manufacturer and model, ranging from about 25 pulses per second to over 1,000 If a metal object passes through the metal detector, the pulse creates an opposite magnetic field in the object. When the pulse's magnetic field collapses, causing the reflected pulse, the magnetic field of the object makes it take longer for the reflected pulse to completely disappear. This process works something like echoes: If you yell in a room with only a few hard surfaces, you probably hear only a very brief echo, or you may not hear one at all. But if you yell into a room with a lot of hard surfaces, the echo lasts longer. In a PI metal detector, the magnetic fields from target objects add their "echo" to the reflected pulse, making it last a fraction longer than it would without them. A sampling circuit in the metal detector is set to monitor the length of the reflected pulse. By comparing it to the expected length, the circuit can determine if another magnetic field has caused the reflected pulse to take longer to decay. If the decay of the reflected pulse takes more than a few microseconds longer than normal, there is probably a metal object interfering with it. The sampling circuit sends the tiny, weak signals that it monitors to a device call an integrator. The integrator reads the signals from the sampling circuit, amplifying and converting them to direct current (DC).The DC's voltage is connected to an audio circuit, where it is changed into a tone that the metal detector uses to indicate that a target object has been found. If an item is found, you are asked to remove any metal objects from your person and

32

step through again. If the metal detector continues to indicate the presence of metal, the attendant uses a handheld detector, based on the same PI technology, to isolate the cause. Many of the newer metal detectors on the market are multi-zone. This means that they have multiple transmit and receive coils, each one at a different height. Basically, it's like having several metal detectors in a single unit. METOR 200

Figure 5.4 Eight overlapping detection zones 5.2.1 METOR 200 (PRINCIPLE OF OPERATION)
The transmitter coils generate a pulsed magnetic field around them. Metal objects taken through the detector generate a secondary magnetic field, which is converted into a voltage level by the receiver coils. Metor 200 consists of eight separate overlapping transmitter and receiver coil pairs. The signal received from each receiver coil are processed individually thus the transmitter and receiver coil pairs form eight individual metal detectors. The operation is based on electromagnetic pulsed field technology as below in addition to the above explanation.

33

Transmitter pulses cause decaying eddy currents in metal objects inside the sensing area of the WTMD. The signal induced to the receiver by the eddy currents is sampled and processed in the electronics unit. Moving metal objects are detected when the signal exceeds the alarm threshold. METOR 200 is a multi-channel metal detector with eight overlapping detection zones.

The zones create a sequential pulsating magnetic field within the detection area of the WTMD. With overlapping construction, sensitivity differences are minimised when metal objects of different shape pass through the WTMD in various orientations Metal objects at different heights are detected separately by the individual zones producing superior discrimination. Advanced microprocessor technology is used for digital signal processing and internal controls. This provides reliable functioning of the metal detector, versatile features and user friendly operations. The electronics unit processes the signals received from the receiver coils. It indicates the result of the signal processing through an alphanumerical display, alarm LEDs and Buzzer. The zone display unit, which is mounted on transmitter coil panel, points out the position where a weapon was taken through the gate. The user controls the functions of the metal detector with a remote control unit. It sends to the electronics unit an IR signal corresponding to the pressed keyboard code. The traffic counter counts the number of persons walking through the gate and the amount of alarms generated. detection

5.3 HHMD
5.3.1 OPERATION
The coil is part of the oscillating circuit which operation frequency is 23.5 kHz. When a metal object is inside the sensing area of the coil, it will effect to amplitude of the

34

oscillating signal. After a while the integrating control will set the amplitude a constant value. Output of oscillator is rectified and it is connected through the filter section to comparator. When the signal is lower than the adjusted reference level (sensitivity setting) comparator generates alarm signal. It activates the alarm oscillator and the audible alarm / the red alarm light. Battery voltage is controlled with a low voltage circuit and constant alarm is activated when the battery voltage is under 7V. The connector in the rear of the unit operates as headphone and charger connections. The charger idle voltage is between 14 and 24 VDC. During charging operation the green light is plinking and with full battery it lights constantly.

Figure5.4 HHMD and Block Diagram

35

5.4 ETD
An Explosive Trace Detector is used to detect the explosives and narcotics. It consists normally a vacuum tube. The operator on swap takes a sample from the luggage. In the ETD machine the sample is melted and then vaporized, by applying high voltage. Thus there is displacement occurs in the atomic weight of the substance. By the LUT (Look Up Table) the displacement can be measured, and thus substance can be detected. The screen of ETD shows the information about the sample with necessary graph etc.

Figure 5.5 ETD

5.5 FIDS
A Flight Information Display system (FIDS) is a computer system used in airports to display flight information to passengers, in which a computer system controls mechanical or electronic display boards or TV screens in order to display arrivals and departures flight information in real-time. The displays are located inside or around an airport terminal. A virtual version of a FIDS can also be found on most airport websites and teletext systems. In large airports, there are different sets of FIDS for each terminal or even each major airline. FID systems are used to assist passengers during air travel and people who want to pick-up passengers after the flight. Each line on an FIDS indicates a different flight number accompanied by:

36

the airline name/logo and/or its IATA or ICAO airline designator the city of origin or destination, and any intermediate points the expected arrival or departure time and/or the updated time (reflecting any delays) the gate number the check-in counter numbers or the name of the airline handling the check-in the status of the flight, such as "Landed", "Delayed", "Boarding", etc.

Due to code sharing, one single flight may be represented by a series of different flight numbers, thus lines (for example, LH474 and AC9099), although one single aircraft operates that route at that given time. Lines may be sorted by time, airline name, or city.

Figure 5.6 Flight Information Display

5.6 PA SYSTEM
It is called Public Address System. At the Airport it is use to address the passengers. Information about the arrival and departure of flights, security checking etc is announced by

37

this system. Here three or more power amplifiers are used in series to amplify the audio power from where the audio output is announced in different sections through loudspeakers.

CHAPTER 6 IT SECTION

IT or the information technology is used basically for transmitting and receiving the information from one place to another place, fast and in an efficient way.

6.1 FUNCTIONS OF IT DEPARTMENT

Planning & implementation of suitable information security & protection system with FIREWALL to ensure safety & security of Database & prevention of unauthorized access to AAI server. Planning & implementation of AAI Internet. LAN /WAN planning connecting all AAI establishment throughout the country on AAI Internet. Development & hosting of AAI website & website management. Use of Web based Information Technology as strategic business tool to improve the business process & efficiency of the Organization. Internet & E-mail services to all the executives of AAI & sections on need basis, initially using dial-up & subsequently using Leased Line & AAI Proxy Server. Hyper link connection for downloading of information on latest flight schedules, arrival/departures of flights on registration basis to third parties such as Hotels, Tour & Travel Operators, Cell Phone & Cable Operators etc. Assessment & planning of IT related Training & in-house application development.

38

6.2 BASICS
6.2.1 Hub
The term is familiar to frequent fliers who travel through airport "hubs" to make connecting flights from one point to another. In data communications, a hub is a place of convergence where data arrives from one or more directions and is forwarded out in one or more other directions.

4.2.2 SWITCH
In a telecommunications network, a switch is a device that channels incoming data from any of multiple input ports to the specific output port that will take the data toward its intended destination. In the traditional circuit-switched telephone network, one or more switches are used to set up a dedicated though temporary connection or circuit for an exchange between two or more parties.

4.2.3 ROUTER
In packet-switched networks such as the Internet, a router is a device or, in some cases, software in a computer, that determines the next network point to which a packet should be forwarded toward its destination. The router is connected to at least two networks and decides which way to send each information packet based on its current understanding of the state of the networks it is connected to. A router is located at any gateway (where one network meets another), including each point-of-presence on the Internet. A router is often included as part of a network switch.

6.3 NETWORKING

39

Today when we speak of networks, we are generally referring to three primary categories: local area networks, metropolitan area networks, and wide area networks. In which category a network falls is determined by its size. its ownership, the distance it covers, and its physical architecture (see Figure below).

Figure 6.1 Block Diagram of Networks

6.3.1 LOCAL AREA NETWORK (LAN).

A local area network (LAN) is usually privately owned and links the devices in a single office, building, or campus (see Figure below).

Figure 6.2 Local Area Network

Depending on the needs of an organization and the type of technology used, a LAN can be as simple as two PCs and a printer in someone's home office; or it can extend throughout a company and include audio and video peripherals. LAN size is limited to a few kilometers.

40

6.3.2 WIDE AREA NETWORK (WAN)

A wide area network (WAN) provides long-distance transmission of data, voice, image, and video information over large geographic areas that may comprise a country, a continent, or even the whole world.

Figure 6.3 Wide Area Network

6.4 NETWORK TOPOLOGIES

6.4.1 BUS
A bus network is an arrangement in a local area network (LAN) in which each node (workstation or other device) is connected to a main cable or link called the bus. A bus network is simple and reliable. If one node fails to operate, all the rest can still communicate with each other.

41

Figure 6.4 Bus Network 6.4.2 STAR

A star network is a local area network (LAN) in which all nodes (workstations or other devices) are directly connected to a common central computer. Every workstation is indirectly connected to every other through the central computer. In some star networks, the central computer can also operate as a workstation.

Figure 6.5 Star Network 6.4.3 RING:

A ring network is a local area network (LAN) in which the nodes (workstations or other devices) are connected in a closed loop configuration. Adjacent pairs of nodes are directly connected. Other pairs of nodes are indirectly connected, the data passing through one or more intermediate nodes.

Figure 6.6 Ring Network

42

6.4.4 MESH:
A mesh network is a local area network (LAN) that employs one of two connection arrangements, full mesh topology or partial mesh topology. In the full mesh topology, each node (workstation or other device) is connected directly to each of the others. In the partial mesh topology, some nodes are connected to all the others, but some of the nodes are connected only to those other nodes with which they exchange the most data.

Figure 6.7 Mesh Network

43

CHAPTER 7 CONCLUSION
The first phase of practical training has proved to be quiet fruitful. It provided me an opportunity to learn about Security Equipments, VHF transmitters, VHF receivers, ATC Tower, ILS, DVOR, DME. At airport various units are linked and the way working of whole unit is controlled make the student realize that engineering is not just learning the structured description and working of various systems but the greater part is of planning proper management. It also provides opportunities to learn about how accuracy is required in the Navigation and Communication purposes. Learning of Security systems was also a great experience. Training is not carried out into its tree sprit. It is recommended that there should be some project specially meant for students where presence of authorities should be ensured. There should be strict monitoring of the performance of students and system of grading be improved on the basis of work done. It has allowed an opportunity to get an exposure of the practical implementation to theoretical fundamentals.

44

BIBLIOGRAPHY

[1] www.airportsindia.org.in [2] www.aai.aero.org [3] en.wikipedia.org/wiki/AAI [4] Manuals provided by Airport officials

45