Professional Documents
Culture Documents
7d48a 1
7d48a 1
Cal. 7D48A
SPECIFICATIONS Item Movement Cal. No. 7D48A
Movement size
Outside diameter
. mm
mm Casing diameter . mm Height Time indication 3 hands (Hour and minute hands: 5-second interval movement, Second (Movement intervals) hand: 1-second interval movement), 24-hour hand Calendar Year indication: Indication disk for year Month indication:Month indicator Date indication: Big calendar Step motor: 2 pieces Piezoelectric motor (for calendar) Driving system Additional mechanism
Automatic generating system Energy depletion forewarning function Overcharge prevention function Electronic circuit reset switch Train wheel setting device Instant setting device for date calendar Automatic power save function Time relay function Perpetual calendar (Year Month Date) up to February 28, 2100
Power supply
Power generator Automatic generating system Electricity Titanium lithium ion rechargeable battery storage Unit (E.S. Unit) 0.45 2.5 Operating voltage range Continuous operating Operable time of time relay function: approximately 4 years if fully time charged Jewels 16 jewels
1.
<The automatic power save function> If the watch is left untouched for approximately 24 hours, the power save function is automatically activated.
2.
(Caution) It may take approximately up to 64 seconds (32 seconds on average) to activate the time relay function. The accuracy of the time computation by the built-in IC is equivalent to that of conventional quartz watches. Especially when the watch has been left untouched for a long time before the time relay function is activated, the time indicated by the hands may include a certain amount of time loss or gain within the range of the accuracy of the watch (15 seconds per month) that has accumulated during that time.
3.
The continuous operating time varies depending on the stored electrical energy inside the watch. In the case that the fully charged watch enters the power save mode,
2
the time relay function of the watch remains operable for approximately four years. (Caution) If the stored electrical energy is completely depleted while the watch is in the power save mode, swinging the watch may not activate the time relay function. Instead, the second hand starts moving at two-second intervals.
4.
PERPETUAL CALENDAR
The perpetual calendar automatically adjusts the date up to February 28, 2100. Even if the watch is in the power save mode, the calendar continues to function as normal. (Caution) The date changes between 23:30 and 0:30. Normally it takes approximately 2 seconds for the watch to change the date. However it may take up to 2 minutes especially during the wintertime or when the stored electrical energy is being depleted. Even though the watch is reactivated after the stored electrical energy has become extremely low, the calendar can be easily adjusted manually. When the watch is in power save mode, and the date does not change correctly (or shows the wrong date), the electrical power stored in the rechargeable battery is being depleted. Before starting to wear the watch, recharge the watch until the second hand no longer moves at two-second intervals and then reset the time and calendar.
5.
Case back
3 4
Oscillating weight wheel 1002 504 Rechargeable battery clamp screw 0012 354
Insulator for rechargeable battery 4216 541 Rechargeable battery unit (MT920) 3023 24X
-4-
Crown
Case
Second hand
Month indicator
24-hour hand
Dial
-5-
Date dial holder for trans wheel for units digit 0839 506 Date dial for ten's digit (0878 A84) Date dial for units digit (0878 A85)
10
11
12
13
1.Supporting pin for alignment To be removed while assembling 2.This is the repairing tool. (7D48A-JP) Please look at the Watch Repairing Tool Catalogue.
1.Positioning pin for spring for intermediate wheel for month indicator To be removed while assembling 2.This is the repairing tool. (7D48A-JP) Please look at the Watch Repairing Tool Catalogue. 14 Train wheel bridge for calendar screw 0012 354
15
-6-
16
Indicator on wheel for month 1021 503 Detection on wheel for month 1002 510 Intermediate wheel for year indicator 0817 516 Detection on wheel for year 1002 511
17 18
19
20 Indicator on wheel for year 1021 504 21 Driving on wheel for year 0802 507
22 Intermediate wheel for month indicator 0817 515 23 Indicator on wheel for 24h 1021 502
24 Detection on wheel for 24h 1002 509 25 2nd intermediate wheel for calendar 0817 513 Control wheel 1002 507 27 Screw for piezoelectric motor cover 0022 230 Piezoelectric motor cover 0839 505
26
28
-7-
29
30
1st intermediate wheel for calendar 0817 512 Piezoelectric rotor block 4146 514
31
32
Insulator for piezoelectric motor 4216 540 Piezoelectric motor lead plate 0105 502 Piezoelectric stator block 4583 500
33 34
35
Jumper for month 1024 504 Positioning pin for spring for intermediate wheel for month indicator To be set for assembling Spring for intermediate wheel for month indicator 1024 503 Jumper for ten's digits 1024 501
36
37
-8-