Type

Type 447 PTFElined Packed lever H4 Closed bonnet Bellows design

447
Contents

Flanged Safety Relief Valves spring loaded

Chapter/Page
02/02 02/04 02/06 02/08 02/10 02/11 Materials Conventional design Chlorine application Configuration Features How to order Numbering system Article numbers Dimensions and weights Metric units US units Pressure temperature ratings Metric units US units Order information Flange drillings Order information - spare parts Available options Approvals Capacities Steam, air, water [metric units] Steam, air, water [US units] Determining of coefficient of discharge Kdr /aw

02/12 02/13 02/13 02/14 02/15 02/16 02/17 02/18

LWN 484.01-E

02/01

Type 447 Type 447

Type 447
Conventional design

40

Cap H2 Lock nut Adjusting screw with bushing Upper spring plate Spindle Bonnet Spring Split ring Lower spring plate Stud Nut Pin Guide Disc with PTFE bellows
7.4 7.6 7.1 7.2 7.3

19

18

16

12

54

14

Type 447

17

55

56

57

Bellows Lift stopper Disc Lifting aid sealing plate

61 5 2 1 56 91

Ball Nozzle Outlet body Inlet body Nut Stud

02/02

LWN 484.01-E

Type 447
Conventional design

Materials
Item. Components Type 447 1.0460 + Virgin PTFE Steel / PTFE-TF 1.0619 + Virgin PTFE SA 216 WCB / PTFE-TF Virgin PTFE with 25 % glass PTFE-TF with 25 % glass Virgin PTFE / BOROFLOAT glass PTFE-TF / BOROFLOAT glass 1.4404 316L Virgin PTFE with 25 % glass PTFE-TF with 25 % glass BOROFLOAT glass Virgin PTFE PTFE-TF 1.4404 Stainless steel 1.4404 Stainless steel 0.7043 Ductile Gr. 60-40-18 1.4404 Stainless steel 1.4104 Chrome steel 1.0718 Steel 1.4104 PTFE Chrome steel PTFE 1.0718 Steel 1.0718 12L13 1.1200, 1.8159 Steel 1.4310 Stainless steel 1.1181 Steel 1.0501 2H 1.4310 Stainless steel 1.3541 Hardened stainless steel 1.1181 Steel

1 2 5 7 7.1 7.2 7.3 7.4 7.6 8 9 12 14 16/17 18 19 40

Inlet body Outlet body Nozzle Disc with PTFE bellows Disc Lifting aid sealing plate Bellows Lift stopper Guide Bonnet Spindle Split ring Spring plate Adjusting screw with bushing Lock nut Cap H2 Spring, standard

54 Spring, optional 55 56 57 61 91
Please observe:

Stud Nut Pin Ball Stud

LESER reserves the right to make changes. LESER may use higher quality materials without giving prior notice. Each component can be replaced by another material according to the customer's specification. All components exposed to pressure are highlighted in bold.

LWN 484.01-E

02/03

Type 447

Type 447
Configuration Features Design features

8 5

9 3

Type 447

6 3 1

Design features
Item. Component Information Inlet body of material 1.0460 (SA 105) and outlet body of material 1.0619 (WCB) with PTFE lining for highest corrosion resistance Vacuum-proof, isostatic full lining of the body components of virgin PTFE with a minimum thickness of 3 mm. All lined surfaces are mechanically processed and have a smooth surface (Ra = 1.6 m). This prevents build-ups of the medium. Nozzle of high-quality, inert gas sintered PTFE with 25% glass for high strength. Sealing plate of BOROFLOAT glass for maximum chemical resistance. PTFE bellows protect the bonnet space against corrosive and aggressive media. To full individual material requests, the following components are exchangeable: inlet body (Item 1), nozzle (Item 5), and sealing plate (Item 7.3). Self-emptying outlet body prevents collection of the medium in the blow-off chamber. Interior bellows support reduces ow loads resulting in a longer service life. Completely metallic support of the sealing plate with disc insert of 1.4404 (316L). LWN 484.01-E

Inlet body + outlet body

2 3 4 5 6 7 8 9 02/06

PTFE lining Nozzle Sealing plate PTFE bellows Inlet body, nozzle and sealing plate Outlet body Bellows support Disc insert

Type 447
Configuration Features Lining procedure-Isostatical manufacturing process
Linings made of isostatic PTFE have proven themselves successfully everywhere where extremely aggressive media is processed. The PTFE lining for cast or metal bodies is produced following the isostatic compression moulding process. PTFE-lined bodies are manufactured in three main production steps: Preparation of the surfaces on metal bodies to be lined Lining with a sintering process Final machining

Main production steps

Information

Preparation for lining

Machining of the body surfaces that will be lined / coated. Roughening the surfaces by subsequent sand blasting.

Lining with a sintering process

Press moulds are placed over the surfaces to be lined and lled with powdery PTFE.

The body is put under pressure of > 500 bar acts on all directions in a pressure vessel. This strongly compacts the PTFE powder and presses it onto the roughened surface of the metal. This results in a form-locked and friction-locked connection between the PTFE and metal. Afterwards, the casing is sintered, through which the lining obtains the strength and low permeability.

Final machining

 achining of the functional surfaces (ange, M support areas, etc.)

 he minimum PTFE wall thickness is 3 mm T ( 1/8 inch).

min. 3 mm ( 1/8 inch)

LWN 484.01-E

02/07

Type 447 Type 447

Type 447
How to order Article numbers

Type 447
DNI DNO Valve size Actual orice diameter d0 [mm] Actual orice area A0 [mm2] 25 50 1" x 2" 23 415 50 80 2" x 3" 46 1662 80 100 3" x 4" 60 2827 100 150 4" x 6" 92 6648

Body material 1.0619 + PTFE-TF (WCB + PTFE-TF) PTFE fully lined Closed bonnet H2 H4 Art. no. 4472. Art. no. 4472. 3872 3874 3882 3884 3892 3894 3902 3904

Note on export inspection

Type 447 is subject to an export restriction according to EU regulation No. 1334/2000 as well as regulation No. 1167/2008 Position 2B350g.
Type 447

Exception
For direct export by LESER, exception EU 001 can be used for the following countries: Australia, Japan, Canada, New Zealand, Norway, Switzerland and USA.

In the event of an export project, LESER requests the respective information on the final destination / use in the inquiry / order.

Type 447
Cap H2 Closed bonnet Conventional design

Type 447
Packed lever H4 Closed bonnet Conventional design

02/10

LWN 484.01-E

Type 447
Dimensions and weights
Metric units
DNI DNO Valve size Actual orice diameter d0 [mm] Actual orice area A0 [mm2] Weight [kg] Centre to face [mm] Height (H4) [mm] DIN Flange1) Inlet Outlet Inlet a Outlet b 15 105 100 465 29 152 120 605 PN 16 PN 16 50 155 155 786 105 220 200 943 25 50 1" x 2" 23 416 50 80 2" x 3" 46 1662 80 100 3" x 4" 60 2827 100 150 4" x 6" 92 6648

Body material 1.0619 + virgin PTFE (WCB + PTFE-TF)

US units
DNI DNO Valve size Actual orice diameter d0 [inch] Actual orice area A0 [inch2] Weight [lbs] Centre to face [inch] Height (H4) [mm] DIN Flange1) ASME Flange1)
1)

25 50 1" x 2" 0,91 0,645

50 80 2" x 3" 1,81 2,576

80 100 3" x 4" 2,36 4,382

100 150 4" x 6"

10,304

33 Inlet a Outlet b 41/4 3 /8

7

64 6 4 /4
3

110 61/8 6 /8
1

231 83/4 77/8 371/8

181/4 Inlet Outlet Inlet Outlet

233/4 PN 16 PN 16 Class 150 Class 150

3015/16

Body material 1.0619 + virgin PTFE (WCB + PTFE-TF)

Standard flange class. For other flange drillings, see page 02/13.

Conventional design
LWN 484.01-E 02/11

Type 447

3,62

Type 447
Pressure temperature ratings

Metric units
DNI DNO Valve size Actual orice diameter d0 [mm] Actual orice area A0 [mm2] DIN Flange Min. set pressure Max. set pressure Temperature acc to. DIN EN1) Inlet Outlet p [barg] S/G/L p [barg] S/G/L min. [C] max. [C] 25 50 1" x 2" 23 416 50 80 2" x 3" 46 1662 80 100 3" x 4" 60 2827 100 150 4" x 6" 92 6648

Body material 1.0619 + virginal PTFE (WCB + PTFE-TF) PN 16 PN 16 0,1 16 -85 +200

US units
DNI DNO 25 50 1" x 2" 0,91 0,645 50 80 2" x 3" 1,81 2,576 80 100 3" x 4" 2,36 4,382 100 150 4" x 6" 3,62 10,304

Type 447

Valve size Actual orice diameter d0 [mm] Actual orice area A0 [mm2] ASME Flange Min. set pressure Max. set pressure Temperature acc to. DIN EN
1)

Body material 1.0619 + virginal PTFE (WCB + PTFE-TF) Inlet Outlet p [psigg] S/G/L p [psigg] S/G/L min. [F] max. [F]
1)

Class 150 Class 150 1,45 232 121 +392  he pressure/temperature functional ranges of Type 447 are T dependent on the PTFE components in the safety valve.

Medium temperature t [C]

0 240 220 200 180 20 40 60 80 100 120 140 160 180 200 16 15 14

The chart shows the application ranges for:

I

II

13 12

Standard safety valve with PTFE/glass nozzle and sealing  plate made of BOROFLOAT glass  afety valve with metallic nozzle and sealing plate of S Hastelloy, nickel, etc.

Set pressure p [psig]

Set pressure p [bar]

160 140 120 100 80 60 40 20 0 40 80 120 160 200 240 280 320 360

11 10 9 8 7 6

II

5 4 3 2 1 0

Medium temperature t [F] Pressure / temperature ranges

02/12

LWN 484.01-E

Type 447
Available options
For futher information, refer to "Accessories and options", page 99/01.

Screwed cap H2 H2

Packed lever H4 H4

Lift indicator J39: Connection H4 J93: Lift indicator

Type 447
Lift stopper J51

Special 2.4610 2.4360 1.4462

materials Hastelloy C4 Monel 400 Duplex

Code YYYY Code XXXX Code ZZZZ

02/14

LWN 484.01-E