KATALOG Toshiba
KATALOG Toshiba
KATALOG Toshiba
TYPE TE
C TYPE TE MC
C TYPE TE MC
CONTENTS
Type TE Motor Control Center Motor Multi-relay Model CCR22 Functions of TE Motor Control Center (M series) Specifications of CCR22 Functions of CCR22 Data transmission equipment Open field network Features of the TE Motor Control Center Construction of vertical busbar Construction of horizontal busbar Construction of unit Ratings/Types Unit circuit diagrams High-capacity inverter cabinet External connection method Power distribution method and installation Dimensions and mass Unit selection table Guidance of the plan Motor Control Center unit layout
(for planning by the customer)
1 3 5 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 26 30
Reliability
Easy maintenance
Operability
Long-life, bright, and large 7-segment LED indicator This LED indicator has longer service life compared to LCD, and indicated values can be read clearly both in bright and dark places. The 6-digit-display helps you recognize at a glance which item is being set.
Easily understandable trip indicator When a trip occurs, the orange lamp will light. The 7segment LED will indicate the cause of the failure and blink.
In addition to power and power consumption, power factor is also measured. It is possible to measure power, power consumption and power factor. These measurements serve for energy-saving. *Pulse output (insulated) for power consumption can be output
as standard.
ERROR COMM.
A %
MON.
DIR. REM.
Protection against corrosive gases Switch contacts and connector contacts on the circuit board are gold-plated and thus resistant to corrosive gases.
kW X1000 kW/h
REV.
OFF
ON/FOR.
RESET
COS
Operating time Switching count Power consumption Monitor switch 6-digit digital indication Switches for settings and selection
Lenses which enable clear and easy view from any direction were adopted. Operation indicator lamps can be seen from above, below, left and right.
Compatible with old-type models As this model is compatible with old-type motor multi-relays, it is possible to renew them and enhance their monitoring functions. Protection, control and monitoring of motors are managed by a PC. Also energy-saving and failure analysis are supported.
Security function Switch operation can be locked by setting the lock-function. The lock will be released by inserting the unlock key.
*Unlock key (optional) Type CCR-RKEY
Protective functions
According to the properties of the load, various protective functions can be chosen to protect the valuable equipment.
Setting range of overload protective funcion
Control functions
According to the usage, various control systems can be selected.
(0.11A--630A)
Input operation condition selection Starting method Operation Stop Reset after failure
C TYPE TE MC
Overload protection
Undercurrent protection
Monitoring functions
Thanks to the enhanced monitoring functions, energy-saving and updating time management for the equipment can be realized. Furthermore, as cause of failure of the load can be identified, functions of the equipment can recover quickly.
Power Monitoring
Power Power consumption Power factor
Time Monitoring
Accumulated operation time Accumulated switching frequency (contactor switching frequency) Starting time Time elapsed since the occurrence of a failure
TOSLINE-F10M
Open field network
*DeviceNet
TM
is a trademark of ODVA.
Motor multi-relay setting tool for function and failure analysis (optional)
The motor multi-relay CCR22 can be connected to a PC using the commercially available USB-cable (Type A -- mini B). Setting data values, current/voltage waveform, protection coordination , can be displayed on the PC s screen. Other features: Fault and Leakage current values -Past 8 times (in % of the load current). -Past 20 seconds before failure to 5 seconds after failure. Insulation can be monitored by detecting very small leakage current(optional). Data can be saved either in TXT or CSV format.
When an instantaneous voltage dip occurs and the voltage does not recover within a preset time period, the motor is stopped. When an instantaneous voltage dip occurs and the voltage recovers within a preset time period, the motor continues to operate.
Motor multi-relay-setting
Fault current
Output Function
0--1mA (not-insulated) or 4--20mA (not insulated) output for the control panel on site is provided as standard. 4--20mA (insulated) output can be provided by an optional circuit board.
In case the instantaneous compensation time as well as the restarting delay time are set In the event of an instantaneous voltage dip, in case the voltage recovers within the preset time period (0.1sec), motors will continue to operate because the in-rush current is small. In the event of an instantaneous voltage dip, in case the voltage does not recover within the preset time period (0.1sec), but it recovers within the instantaneous compensation time, motors will restart. However, if a number of motors would start simultaneously, the in-rush current would become very large. For this reason, the motors will restart in the order that was set when setting the restarting delay time.
WH
Instantaneous compensation time for immediate restart
< Duration of power failure<100ms Duration of power failure 100ms
*It is not possible to use the 4-20mA output and the transmission function simultaneously.
It is possible to output pulse of power cosumption (insulated) as standard. (1 pulse is output for 10Wh, 100Wh and 1kWh.)
Maintenance
Since the electrolytic capacitor has a relatively short life among the other electronic components, the motor multi-relay CCR22 has a circuit board structure in which the electrolytic capacitors can be changed easily. When changing a capacitor, it can be detached easily by removing 3 screws combining the main circuit board of CCR22 and the capacitor circuit board.
Operation Stop Operation Stop Operation Stop Motor3 Motor2 Motor1
80ms Operation Stop Operation Stop Operation Stop Motor3 Motor2 Motor1
500ms
Immediate restart
If the motors would restart immediately, the in-rush current would become very large. For this reason, motors restart successively.
Specifications of CCR22
Functions of CCR22
CCR22 consists of circuit boards (incorporated into the operation panel) and a case. Dependent on the used load and the purpose of control, main circuit board, expansion circuit board and transmission circuit board are combined.
L4 L10 L9 L1 1 L2 L1 L5 L7 S5 L8 S1 1 S9 S7
Description 35 to 105% (unit: 1%) 115% of the set-up current 0.11 to 630 A None, 50 to 100% (unit: 1%) of the set-up current
Reset
Auto and Manual None, 30%, 60% None, 30, 100 to 500 mA 0.1 to 1 sec (unit: 0.1 sec) None, 30 to 95% of the sensitivity current (unit: 1%) None, 40 to 600% of the set-up current (unit: 5%) 0.1 to 9 sec (unit: 0.1 sec) 1 to 180 sec (unit: 1 sec) None, 15 to 100% of the set-up current (unit: 1%) 0.2 to 9 sec (unit: 0.1 sec) 1 to 200 kW 0.1 to 10 sec 1 to 200 kW 0.2 to 10 sec Digital (A) or percentage (%) switchable Digital (A) Indicated in kW Indicated in kWh Percentage (%) Non-operation monitoring 1 sec after switching operation Switching (twice or more) within 0.15 sec monitoring Operation time accumulation monitoring Accumulated switching count of the contactor Overload, overload pre-alarm, grounding, pre-alarm for grounding, single phasing, instantaneous overcurrent, undercurrent, power overload, under power, starting jam, contactor trouble, and contactor chattering
Time from the start of the operation until the current becomes 110% or less
Protective functions
2 to 90 sec
Sensitivity current Grounding protection Operating time Pre-alarm operating current Operating current
Front panel
Instantaneous Operating time overcurrent protection Starting operation lock time Undercurrent protection Power overload protection Under power protection Operating current Operating time Set-up power Operating time Set-up power Operating time
10
100
600 1000
Current (%)
S3
S2
S1
S4
L3
L6
S6
C1
S10
S8
No.
S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 S11 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 C1 ON/FOR. OFF REV. RESET MON. COS SEL. ENTER
Name
Function
To start the motor (in the forward direction). Lit in red while the motor is running. To stop the motor. Lit in green when motor is idle. To start the motor (in the reverse direction). Lit in red while the motor is running. To reset the protective function. Lit in orange during failure (while the protective function is operating). To select the display on the monitor. To select the operating location (remote or local). Selects a fault display and a function setting display and to change setting. To enter setting values. To select functions and to change values (increasing the values) To select functions and to change values (reducing the values) To cause a test trip during test For digital display of current For % display of current For indication of electric power *1, *2 For displaying hours (In the case of 1 hour, the display is 0.001.) For displaying the count (In the case of 1 time, the display is 0.001.) For indication of wattage per hour *1, *2 This indicates the location of the operation and is lit when the local operation can be made. This indicates the location of the operation and is lit when the remote operation can be made. This is lit when the CPU fails. This is lit when transmission is normal. This digitally indicates a current value and a setting value. Connectors for function setting and for reading of maintenance data (For PC connection)
Operating current monitoring Leakage current monitoring Power monitoring Power consumption monitoring Power factor monitoring
Switches
LED
Connector
TEST TRIP A % kW x1000 HOUR x1000 COUNT x1000 kWh DIR. REM. ERROR COMM. Digital indicator Communication connector
Monitoring functions
Control voltage monitoring(insufcient voltage) 80% or less of the relay rated voltage Contactor monitoring Chattering monitoring Accumulated operation time monitoring Accumulated switching count monitoring Failure factor indication Starting time Elapsed time indication Faulty current indication Input operation condition selection Output condition selection Starting method Load applied Operation stop Remote and direct switching selection
Type (CCR22)
1st digit
*1 Power indication is only possible when the type of the connected current sensor is CV3. *2 Electric power and wattage per hour at the secondary side of the inverter cannot be measured.
0:100Vac/110Vac without expansion board 1:100Vac/110Vac with expansion board Control 2:200Vac/220Vac without expansion board voltage 3:200Vac/220Vac with expansion board 0: None 1: TL-F10M(T-US005) Optional 2: CC-Link(C-US002) board 3: Transducer (CCR22-AN) 4: DeviceNet(D-US001) 0: Standard Case 1: Old type, MMR compatible 0:CV3 (standard)ZCT Hikari Trading (standard) 1:CV3 (standard)ZCT Seiko Electric CV.ZCT 2 CV2 ZCT Hikari Trading (standard) 3 CV2 ZCT Seiko Electric 0: None Optional function 1: Voltage dip compensation time 0.2sec. compensation (optional) 0: Standard User sequence 1: Variable sequence used For future use 0: Standard
General Specifications
Control functions
Output conditions can be selected from 35 types via 2 standard relays and 3 optional relays. Non-reversible, reversible, - , closed - , pole change, reactor, Korndorfer, inverter non-reversible, inverter reversible Single-phase load, three-phase load Operation, Stop, and Trouble Reset by illuminated (LED) push-button switch With Remote (REM) or Direct (DIR) switching. 5 types of circuit conditions can be selected.
100
1000
Current (%)
Power supply voltage: 20 Vac: 50/60 Hz Allowable voltage variation: 85 to 110% Operating voltage: 100/110Vac 50/60Hz Noise resistance: Service temperature: Storage temperature: Service humidity:
200/220Vac 50/60Hz 2000 V for 1s (by noise simulator) --10 to +60 --20 to +60 10 to 85% RH (no dew condensation can result) There should be no dust nor corrosive gas. 100M (500V megger) (between terminals tied together and ground)
2nd digit
3rd digit 4th digit 5th digit 6th digit 7th digit
Instantaneous compensation time None, 0.5, 1, 2, 3, 4, 5 sec, 10 to 60 sec (unit: 5 sec.) Restarting Instantaneous compensation time 0.1, 0.2 sec (optional) after for immediate restart voltage dip Restarting delay time 1 to 180 sec (unit: 1 sec) Operation in stop Transducer output
Stop or continue operation is selected in the case of CPU problem.
0 to 1 mA (not insulated) or 4 to 20 mA (not insulated) For problem simulation at a sequence test USB
Other
10
An open field network --- CC-Link and DeviceNetTM --is used to meet different needs.
*Supplied for M series (optional). Can be connected to many items of field equipment compatible with CC-Link and DeviceNetTM thanks to open transmission equipment. Full fledged and highly reliable functions -A standby master is set up. Therefore, data link is active if an error has occurred in the master station. -When an error has occurred in a slave station while data link is being activated and it is made inactive, the slave station is disconnected and data link is activated between normal stations only. Thanks to the DeviceNetTM whose specification has been made public throughout the world, our motor control centers can be connected to any PLC(programmable controllers) of other manufacturers even if the superordinate system is of another manufacturer. Data transmission is performed by high speed transmission (CC-Link:625 kbps, DeviceNetTM:125 kbps). Transmission cable is a special cable and transmission distance is up to 900m for CC-Link, and up to 500m for DeviceNetTM. The number of unit stations connected can be, in the case of CC-Link, up to 42 for a master station when one station is occupied, and, in the case of DeviceNetTM, up to 63 for a master station.
CC-Link
General specifications
Specification Description Twisted pair cable (special cable) 900m at maximum 625kbps 85ms (one station occupied, 42units 42/master station Polling CRC check Photo coupler Transmission cable Communication distance Transmission speed Scan time Number of units connected Communication method Check method Insulation method
DeviceNetTM
General specifications
Specification Transmission cable Communication distance Transmission speed Number of units connected Communication method Insulation method External power source Description Twisted pair cable (special cable) 500m at maximum 125kbps 63/master station Polling/Explicit message Photo coupler(insulation inside of the unit)
Network power source DC24V (DC24V needs to be supplied by the external power source)
General specifications
Specification Transmission cable Communication distance Transmission speed Scan time Number of units connected Transmission functions Check method Insulation method Description Twisted paircable (special cable) 2 km at maximum 100ms 128/main station Cyclic scan transmission, Message transmission CRC check Photo coupler
Scan transmission
750kbps
Message transmission
Note: The general purpose relay can, with no restriction, set up the causes of problem such as overload plus single phasing, grounding, pre-alarm, etc.
11
Word information
12
(1)Estimated short-circuit current which is cut off by the MCCB combined with a current-limiting wire
Installation condition
Height Width Depth
M series G series
Basic type (2300X600X550) Wide type (2300X700X550) Thin type Low type
(2300X600X350) (1900X600X550)
70kA
In addition, the following panels can be supplied. Emergency D series motor control center B series power distribution panel for lighting and miscellaneous power circuits.
Example of Application In the diagram on the right, (1) is short-circuit current. When the circuit breaker of 50AF (switch-off capacity 7500A) is combined with current-limiting wires, the current can be cut off like (2) because the current-limiting wires limit current to the cut-off range of the circuit breaker of 50AF. Thus, the electromagnetic force acting on the equipment and the heat shock can be reduced, and at the same time, occurrence of arc at cutting off can be minimized so that overvoltage can be prohibited.
Vertical busbar Vertical busbar cover Vertical busbar Horizontal busbar Vertical busbar cover Vertical busbar support
The circuit breaker for the main circuit of the type TE motor control center consists of a spring contactor and a repulsive conducting plate. Fault current flows through the route (1),(2) and (3) indicated by arrows. Mechanism: The spring force of the contactor itself will keep the contactor tight together. The electromagnetic force F arising at (1) - (1) increases the contact pressure of the contactor. The electromagnetic repulsion arising at (1) - (2) will be counteracted by means of a pin, thus maintaining contact pressure of the contactor. This way, the contact of the vertical busbar and the circuit breaker will not easily be separated.
Electric wire
Repulsive plate
Contactor
Pin F
Vertical busbar
No. BG-05-003
13
14
The vertical busbar is front side, back side independent type compatible with the unit. The vertical box is manufactured by high strength molding technology with at least 1.6t steel plate in compliance with UL845. It must be chosen from protective structure by IEC60529.
The horizontal busbar is longitudinally arranged on the top of cabinet on which cable can be drawn on up side and down side safely (I-line busbar). The vertical busbar is entirely-insulated having a barrier between phases to prevent erroneous contact and propagation of arc discharge. Two-sides type is of a busbar structure with independent front side and back side. 3 phase, 4 wire type can also be selected. The size of neutral phase of 3 phase, 4-wire type horizontal busbar is one-half that of positive phase as standard. It complies with IEC60439-1 and JEM1195. The horizontal and vertical busbars are made of copper. The horizontal busbar is tin-plated for resistance against corrosion and the vertical busbar, having a sliding portion, is silver-plated against abrasion. The unit opening of vertical busbar has an insulation plate for shielding. Unit mounting and dismantling can be done without exerting influence on the operations of up side unit and down side unit. A shutter can also be supplied as an option according to customers specifications. The live part section of main circuits in the wire room is , isolated to secure the safety of adjacent unit s modification and wiring works. The horizontal busbars are positioned in the same manner as for the existing panels of TM type. Note, however, units are not compatible.
Vertical busbar
TYPE TE MCC
Protective structure
General Water protection Dust protection Outdoor type IP20 IPX2 IP5X IP33W(walk-in, non-walk-in)
2100 2300
Vertical busbar
In addition to the basic cabinet style, the following cabinets can be supplied at customer request.
Divided into 3 portions as standard for shipment. See the outline drawing for the division points.
440 600
160
100
550
Vertical cross-sectional view of basic type (back to back) Vertical cross sectional view of thin type
Unit W-M grip Vertical busbar Horizontal busbar Vertical busbar W-M grip Vertical box Unit Wire ways Unit Wire ways
Horizontal busbar
Unit door
Unit door
*In the case of the back to back type, vertical busbars are for R phase, S phase, and T phase from the left on the front side and back side, and the units can be mounted on the front side and back side.
15
16
Construction of unit
Ratings/Types
M series accommodating the motor multi-relay and G series having a thermal relay can be supplied. These types can be combined when necessary and can be mounted on the same vertical box.
*See Unit Selection Table (on pages 24 and 25) for unit size.
Unit (M series)
Types
Bank type
TE - 50 G
Type Rated breaking capacity 30:30kA 50:50kA 70:70kA Series symbol G : thermal relay incorporated M: motor multi-relay incorporated
The unit is racking screw type and can be placed at the following positions. For a large unit with which pulling-out is not feasible, only the circuit breaker unit can be pulled out.
Unit position Connection position Test position (Disconnection position) Main circuit Connection Disconnection Auxiliary circuit Connection Overall test: connection Unit test: disconnection
Unit (G series)
Rated short time withstand current Rated breaking capacity Dielectric voltage at commercial frequency
*At the test position (disconnection position) the unit door is closed.
The circuit breaker control handle (multiple handle) has the following functions.
Unit type
NR 2 - 20 M
Unit styles Unit heights 1.5 : 150mm 2 : 200mm 3 : 300mm Unit rated current Indicates the rated current of electromagnetic contactor for the starter unit. Indicates the frame current of circuit breaker for the feeder unit. Indicates the capacity (kVA) of inverter for the inverter unit.
Without ground With ground fault protection fault protection NR (S) ML (S) HR (S) HL (S) RG (S) RL (S) RM (S) KL (S) VR (S) VL (S) PD (S) DL (S) PT (S) PL (S) YD (S) YL (S) XS (S) XL (S) IN (S) IL (S) NF NL ND BL CL CF GR GL ST SL TT TL ES DS AU Applied unit Non reversible Non reversible (SSC) Reversible (general) Reversible (with mechanical) Reversible (SSC) Pole change (2xMC) Pole change(3xMC) Star delta Reactor start Inverter MCCB, FU-SW feeder 2 circuits incorporated by MCCB feeder MCCB having MC, FU-SW feeder Group starter 1 TR (MCCB with FU-SW) 3 TR (MCCB with FU-SW) Empty unit Space not usable for unit Others
Trip indication
Standard
Optional
Handle lock
Protection method M : motor multi-relay incorporated (M series) T : motor multi-relay(with transmission equipment) incorporated Note: S in parentheses is for the case in which a compact circuit (M series) breaker is used. It is described as NRS for example. : thermal relay incorporated (G series)
Padlock (option) Note: E is attached to a unit for the future (wired in the cabinet).
17
18
Features of inverter VF-AS1 Incorporated noise filter 200V: 0.4-7.5kW 400V: 0.75-75kW Excellent motor control performance Stable control for both drive and regeneration is realized. Setting can be easily done by auto-tuning. Incorporated d.c.reactor 200V: 11-45kW 400V: 18.5-75kW The inverter unit has the same size as the Type TE motor control center M- and G-series so that the cabinets can be lined up easily and a good ventilation effectiveness can be achieved. Networks with monitoring and controlling devices can be built up by means of the transmission devices (CCLink, DeviceNetTM).
Stanard specification AC690V AC200, 220, 400, 440V AC100, 110, 200, 220V 50, 60Hz 800, 1200, 1600, 2000, 3150A 400, 600A 30, 50, 70kA/0.5sec 30, 50, 70kA at 480V 2500V/minute 1500V/minute Main circuits Auxiliary circuits Horizontal busbar Vertical busbar
Rated frequency
Rated busbar current
Input reactor
Rated short-time withstand current Rated breaking capacity Dielectric voltage Main circuits at commercial Auxiliary circuits frequency
Inverter
19
20
The types of motor control center and external connection methods are specified by the standards (JEM1195) as shown in the figure. It must be specified when ordering. The following external connection methods are provided as makers standard. The most suitable one can be chosen according to unit piling-up and operability. A screw-up terminal board is adopted for the control circuit terminal board to reduce control cable connection work. (Up to 2mm2 is good for the control cable. 5.5mm2 is optional.)
There are the following power distribution methods. The most suitable one must be selected according to the network, capacity, and installation space. Consult us for details.
Power distribution with air circuit Power distribution with wiring circuit Power distribution with drop breaker (ACB power distribution) breaker (MCCB power distribution) wiring panel Direct power distribution on back side
MCCB
A No terminal board for load is provided. It is directly connected to the terminals of equipment in the unit.
Features
Figures
600
BC Method B Method C 7 10
Second only to BB method in economicalness. Applicable when there are many control cables.
CB Method C Method B 7 10
Second only to BB method in economicalness. Applicable when main circuit cables are thick.
CC Method C Method C 7 10
Applicable when method C is adopted both for main and auxiliary circuits.
The dimensions in parentheses ( ) are for wide type. The dimensions in boxes are for thin type. When the number of cabinets is more than 4, a combination of 1 - 4 will be adopted.
440 2300 A
A-A cross sectional view [Basic type and wide type] [Thin type]
Descriptions
A power distribution panel for which air circuit breaker is used. Available for one line and two lines. Current capacity is 4000A or less.
A power distribution panel for which a wiring circuit breaker is used. Current capacity is 2000A or less.
A method in which a drop wiring panel is provided. Current capacity is 4000A or less.
A method in which the back side of motor control center is used. Horizontal busbars or vertical busbars are used for power distribution.
Installation
38 50
60
60
38
38 50
60
68
B A 600 700
Base 30 490 30 30
Base 250 30
100 30
100 60
100
500 (600
500 (600
100
120
215
30
100
100 120
100
500 (600
30
500 (600
100
21
30
215
22
Indoor type
D1 D2
Outdoor type
3.7 7.5 11 15 22
YL 3 YL 3 YL 3 YL 3 YLS 4 YLS 5 YL 6 YL 6 YL 10 -
H1
NRS 2 - 50M MLS 2 - 50M RMS 4 - 50M KLS 4 - 50M NRS 2 - 80M MLS 2 - 80M RMS 5 - 80M KLS 5 - 80M NR NR NR NR NR NR 4 - 95M ML 6 - 180M ML 6 - 180M ML 6 - 180M ML 9 - 220M ML 9 - 400M ML 4 - 95M RM 6 - 180M RM 6 - 180M RM 6 - 180M RM 5 - 95M KL 9 - 180M KL 9 - 180M KL 9 - 180M KL 5 - 95M 9 - 180M 9 - 180M 9 - 180M
H2
37 45 55 75 90
W1
W2 W
W2
W2
Note: The size is different when the external ammeter has a CT. If 1.5 size unit is needed, please consult with us.
Starter/feeder panel
ML ML ML ML
2 - 20 2 - 20 2 - 35 2 - 35
* RM * RM
RM RM
2233-
20 20 35 35 50 80 95
* KL * KL
KL KL
2 2 3 3 -
20 20 35 35 50 80 95
YL 4 YL 4 YL 4 YL 4 YLS 5 YLS 6 YL 9 YL 9 YL 11 -
RMS 4 RMS 5 RM 6-
KLS 4 KLS 5 KL 6 -
3 3W Power distribution for 1 line 3 4W ACB accommodated 3 3W Power distribution for 2 lines 3 4W
1400 1500 1400 1500 1400 1500 1400 1500 550 800 550 550 550 350
NR 11 - 400
W1+400
D1+500
Note: The size is different at some portions when it has an instantaneous restart timer. The size is different when the external ammeter has a CT. (*) indicates an auxiliary relay is accommodated. If 1.5 size unit is needed, please consult with us.
C method
14mm2
NL
2-
50
Power distribution capacity: 1200A or less MCCB accommodated Power distribution capacity: 2000A or less Side panel Power distribution capacity: 4000A or less Basic type Starter/feeder Wide type panel Thin type
38mm2
38mm2
W2+300
D2+500
NF 3 - 225
NL
4 - 225
W2
D2
CF 6 - 180 CF 9 - 180
Note: The dimensions and mass of ACB power distribution panel are for SSTD method. The mass for the starter/feeder panel is for one-cabinet type. The dimensions of outdoor type are for non-walk type.
NF 4 - 400
NL
7 - 400 9 - 600
CF 9 - 400
23
Note: The size of unit depends on the circuits and devices accommodated. Please consult with us. The size is different when the external ammeter has a CT or unit is equipped with auxiliary relay. *Entirely fixed type
* NF
5 - 600
* NL
* CF21
- 600
* CL21
- 600
24
200V class
With ground fault protection Unit size
Standard specification SI unit ISO standard Japanese, English Japanese, English JIS, IEC Indoor -5 up to +40
Optional specification
0.75 1.1/1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200
44446611111111161919191921212121-
18M 31M 44M 80M 110M 130M 210M 250M 310M 370M 500M 600M 720M 880M 1220M 1360M 1640M 1970M 2390M
44446611111111161919191921212121-
18M 31M 44M 80M 110M 130M 210M 250M 310M 370M 500M 600M 720M 880M 1220M 1360M 1640M 1970M 2390M
600W550D
600W550D
11M 418M 430M 442M 4 67M 46- 100M 8- 130M 11- 210M 12- 250M 12- 290M 13- 340M 19- 460M 19- 550M 21- 670M 21- 840M 21- 1090M
11M 418M 430M 442M 4 67M IL 4IL 6- 100M IL 8- 130M ILS 11- 210M ILS 12- 250M ILS 12- 290M IL 13- 340M IL 19- 460M IL 19- 550M IL 21- 670M IL 21- 840M IL 21- 1090M IL IL IL IL IL 21- 1330M
As specified by the customer As specified by the customer FormerJIS, NEMA Outdoor --5 and under +40 or more Not to exceed 3000m above sea level As specified by the customer As specified by the customer Polyurethane enamel High-gloss (70) Low-gloss (10) 125mm at the maximum As specified by the customer As specified by the customer
General
Electrical symbol Location Ambient Site condition Temp. Altitude Limit of transportation External and internal surface Components on the door Material Gloss Thickness
Arrangement of main circuit
100mm2
Not to exceed 2000m above sea level No (3 Panels at the maximum) 5Y7/1 N1.5 Melamine enamel Semi-gloss (40) External (40 m), Internal (30 m) 1st, 2nd, 3rd, and neutral phase from front, top, or left-hand side P. -pole, and N. -pole from front, top, or right-hand side Red(R) 1st phase 2nd phase White (S) Blue (T) 3rd phase Black (N) Neutral phase Red(R) 1st phase Black (N) Neutral phase Blue(T) 2nd phase Red(P) Positive pole Blue(N) Negative pole 600V rubber insulated wires Crimp type terminal (Ring tongue, Non--insulated) (Crimp type terminals (Fork tongue, Non--insulated) are used for some points) None Crimp type for 325mm2 or less Compression type for over 325mm2 None Vinyl tube (Not for the inside of the unit) Yellow: AC and DC, Ct 2Ry, Vt 2Ry Black: Shielding 1.25mm2 1.25mm2 0.5mm2 600V Ecological polyethylene insulated Wires
200mm
IN 21- 2950M
21- 2950M
IN 21- 1330M
Note: A different unit size is used when an option other than a reactor for coordination with the power supply is accommodated.
200V class
With ground fault protection Unit size
0.75 1.1/1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200
44446610 10 11 11 15 19 19 19 19 21 21 21 21 -
18 31 44 80 110 130 210 250 310 370 500 600 720 880 1220 1360 1640 1970 2390
66666610 10 11 11 15 19 19 19 19 21 21 21 21 -
18 31 44 80 110 130 210 250 310 370 500 600 720 880 1220 1360 1640 1970 2390
600W550D
600W550D
IN
411 18 IN 4 30 IN 4 42 IN 4 67 IN 4 IN 6 - 100 IN 8 - 130 INS 11 - 210 INS 12 - 250 INS 12 - 290 IN 13 - 340 IN 19 - 460 IN 19 - 550 IN 21 - 670 IN 21 - 840 IN 21-1090 IN 21 - 1330
611 18 IL 630 IL 642 IL 667 IL 6IL 6 - 100 IL 8 - 130 ILS 11 - 210 ILS 12 - 250 ILS 12 - 290 IL 13 - 340 IL 19 - 460 IL 19 - 550 IL 21 - 670 IL 21 - 840 IL 21 - 1090 IL 21 - 1330
IL
Main circuit
600V ecological polyethylene insulated wires Crimp type terminals (Ring tongue, Non--insulated) are used for all points. Provided Clamp type Compression type Vinyl tube Plastic ring Vinyl tube (Include with the inside of the unit) As specified by the customer 2.0mm2 2.0mm2 3.5mm2 5.5mm2 1.25mm2 600V Polyvinyl chloride insulated wires 600V Non--corrosive wires 600V wires (UL44 type SIS)
Crimp type terminal (Ring tongue, Non--insulated) Crimp type terminal (Ring tongue, Insulated)
38mm
100mm2
200mm2
Identification of phase code Wire mark Color of wire Size of wires Auxiliary circuit Type of wires for the inside of the unit for the outside of the unit Provided Type of cable terminal Size Inside the unit AC/DC
Outside the unit Vt/Ct 2Ry
IN 21 - 2950
IL 21 - 2950
Note: A different unit size is used when an option other than a reactor for coordination with the power supply is accommodated.
Single phase transformer unit (circuit breaker for wiring, accommodating a transformer)
Transformer capacity (VA) General Primary voltage 400V class Maximum applicable cable size With ground Secondary Secondary fault protection voltage voltage
100V class 200V class
General
Primary voltage 200V class Maximum applicable cable size With ground Secondary Secondary fault protection voltage voltage
100V class 200V class
Shielding
14mm2
14mm2
14mm2
14mm2
Crimp type terminal (Fork tongue, Non--Insulated) Crimp type terminal (Fork tongue, Non--Insulated) None Crimp type terminal 2.0mm2 at the maximum
100mm2
Note: A unit with 7.5 kVA or more is only for one-side type.
25
26
ITEM Color of wires Size of wires Type of wires Grounding Provided Outside cable terminal lug Type Size
Standard specification Green 2.0mm2 Same as auxiliary circuit Provided Connecting point is shown in the outline drawing. Crimp type terminal (Ring tongue, NonInsulated)
Optional specification Yellow/Green 3.5 up to 5.5mm2 Same as auxiliary circuit Connecting point as specified by the customer As specified by the customer As specified by the customer 3 4W 690V 300V DC 1200 up to 4000A 600A 30kA/1sec 50kA/1sec
Incoming
ITEM
Standard spesification Acrylic resin Black letters on white Panel name Load name Panel name Load name Bolted Card holder Top of the center in the group Unit door None
Optional specification Acrylic resin plate. Color specified by the customer Aluminum Laminated Bolted Position specified by the customer Mounted also on the back door Steel Polyvinyl chloride Fireproof plate With MCCB Incoming panel With ACB V--bus As specified by the customer Group transformer External power supply Direct Remote and direct switching selection Auto and manual switching As specified by the customer As specified by the customer As specified by the customer ON/OFF monitoring Draw--out to outside Impossible to open the door with OFF. Possible to open the door at REST position. Impossible to draw--out or push--in with ON. Regular no--excitation system Delayed return system Without the specification shown in the left column. Class--AC4 No.0 Grade--0 As specified by the customer Depending on circuit condition Missing phase type, delayed action type Mechanical reset 0.03 0.5A
Material
Nameplate
Construction
Ratings
38mm2 3 3W 600V Rated insulation Main circuit voltage Auxiliary circuit 250V AC 480V and below Rated voltage 50, 60Hz Rated frequency 800A Horizontal bus Rated bus current Vertical bus 400A Rated short-time withstand 30, 50, 70kA/0.5sec current: Phase Rated breaking capacity Dielectric test voltage Rated voltage (Auxiliary circuit) Main circuit Auxiliary circuit Operation circuit Alarm circuit 30, 50, 70kA Sym. Rms (at 480V) 2200V/1min 1500V/1min AC100V/50Hz AC110V/60Hz JEM 1195 Japanese standard S=one side only D=double front 600W x 2300H x 550D 2 (electrical interlock with external) B (directly connected to the unit) B (directly connected to the unit) B (MCCB) W (draw-out) d (Interlock between door and MCCB, panel indication, and panel operation systems) 3 C (TR and Indication for each unit) Bottom (cable pit) Bottom (cable pit) Bottom (cable pit) General (IP20) 1.6mm (Door for panel: 2.3mm) 2-split hinge type Type Foundation base Installation 60W x 50H Floor mount with anchor
Bottom plate
Direct None Unit transformer Remote None 49x, 52 (a contact) 49 With alarm contact Impossible to open the door with ON. Possible to open the door with OFF. Impossible to ON with door--open. None Regular excitation system Instantaneous return system AC100V/50Hz AC110V/60Hz Class--AC3 No.1 Grade--1 2a2b 2--element thermal Electrical reset 0.2A 0.2sec Manual AC100V 0.5sec 3 times extended scale LED AC100V 30 500mA 0.5, 1, 2, 3, 4, 5sec 10 60sec (unit: 5sec)
2500V/1min 2000V/1min Without the specification shown in the left column Not exceeding 250V IEC60439 NEMA None 700W x 2300H x 550D 600W x 2300H x 350D 600W x 1900H x 550D 1(without electrical interlock) C C X (fixed)
Schematic diagram
Operating method External contact for operation External contact warning Alarm
Circuit breaker
Electromagnetic contactor Auxiliary relay
Applicable standards
MCC Components Type Panel size Class (NEMA standard) Main circuit External connection method Auxiliary circuit Protection unit of main circuit Unit mounting arrangement Operation configuration Separated with a split plate Monitoring control components Incoming Termination Load cable for ent. Cable (position) Auxiliary cable Protective structure Thickness of door
Excitation system Return system Coil voltage Rated contact (Open/ Closed) capacity Auxiliary contact Protection Protection
Type specifications
against overload
G Series
Reset system
Top Top Top Drip proof (IPX2) Dust proof (IP5X) Outdoor type (IP33W) 2.3mm 2-split hook type 50W x 100H 100W x 50H Flush Semi-flush As specified by the customer
Rated sensitivity current Operating time Reset Coil voltage Instantaneous stop and restart Setting time Ammeter Signal lamp
Grounding protection
As specified by the customer Auto AC200V As specified by the customer With red pointer AC200V
Construction
Rear door
M Series
0.2sec
Output current
Material of busbar
Horizontal busbar Copper (Tin coating) Copper (Silver coating) Vertical busbar Grounding busbar Copper (Tin coating)
Power consumption Pulse output: 1 point (insulated) Pulse output Transmission None
Yes
27
28
ITEM Capacity
Operating transformer
Standard spesification 50, 150, 500VA 50Hz 60Hz 400/100V, 200/100V 440/110V, 220/110V 15VA, 1st class 5A Construction, Electrical operation, Withstand voltage Yes None
Optional spesification Without the specification shown in the left column Without the specification shown in the left column 40VA, 1st class 1A As specified by the customer As specified by the customer As specified by the customer
Rated voltage
55
Front side
Current transformer
2300
100
2100
600
Back side
Caution
Before using the Type TE Motor control center, read the operating manual with a great care to ensure completely familiar with it. For safety of operation, never modify the Type TE Motor control center or add extra functions which are not described in the manual. When modification or addition is to be done, contact Toshiba. Observe the following operating conditions to fully utilize the performance capability of the Type TE Motor control center. In the case that different operating conditions are inevitable, specify them at the time of placing your order. 1) Ambient temperature: -5 to 40C (daily average of 35C or below) 2) Relative humidity: 45 to 85% with no condensation 3) Free of excessive water vapor, oil mist, smoke, dust, salt, and corrosive and inflammable hazardous gases. 4) Free from abnormal vibration and shock.
*Besides the space for the units, space for power supply lines is needed. *In case of wiring BC, CB, CC and RC, space of approxmately 600mm is needed for installing terminal blocks.
29
30
Notes on safety
Before installation, connection, operation, or maintenance, the catalog, manual, and documents attached to the products must be read with great care. The customer must be acquainted with the performance and principle of equipment and laws relevant to electrical equipment and work.