Horia

Price list 2013
Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Tel. +41 32 422 60 70 Fax +41 32 422 60 71 horia@bluewin.ch
Watchmaker's Lathe - Assortment

Ref. TH 40 Watchmaker's Lathe on his table
CHF 7'450.00
Watchmaker's lathe with motor, command, table, board and 4 drawers for the tools
1 work table with board
1 motor 3 x 220 / 380 V, 0.09 KW, 50 Hz, IP 54
1 frequenz converter M 2200-I-IPOO, 220 V, 50 Hz
1 command station with potentiometer and runner-inverter (3 m cable for network 220 V)
1 lathe foot ref. TH 1
1 lathe bed ref. TH 4
1 headstock ref. TH 5
1 tailstock ref. TH 6
1 tip-over T rest ref. TH 10
Equipment of the drawers on request
Ref. TH 40a Drawer 1
CHF 3'850.00
18 arbor 2 mm ref. TH 25
15 pivot chucks ref. TH 37
Centred chuck holder ref. TH 24
Eccentric chuck holder ref. TH 24a
Complete apparatus for drilling and fitting pivots ref. TH 26
Simple device for drilling and fitting pivots ref. TH 27
Disc with 10 holes ref. TH 28
Eccentric slide device, 2 pulleys ref. TH 23
24 small carriers, 0.20 - 1.20 mm with block ref. TH 38
Fixing appliance for carriers ref. TH 38a
Steel disc with 18 notches, for rolling pivots 0.35 - 1.40 mm, ref. TH 29
Bronze disc with 18 notches, for burnishing 0.35 - 1.40 mm, ref. TH 29a
Ref. TH 40b Drawer 2
CHF 9'360.00
60 chucks B 8 mm from 0.40 to 7.00 mm ref. TH 15D

5 hollow chucks, capacitiy 8 - 12 mm, ref. TH 16
4 step collets, capacity 5.5 23 mm, ref. TH 17a
12 special funnel-collets, capacity 5.5 - 22.5 mm, ref. TH 18
6 steel carriers ref. TH 20
6 steel carriers ref. TH 20a
4 wax chucks ref. TH 21
16 chucks and arbors 5 mm ref. TH 22
1 Chuck holder ref. TH 22a

Ref. TH 40c Drawer 3
CHF 5'479.00
Lever pump attachment for drilling and turning, with 3 split chuck, ref. TH 11
Very light tool post, movable in all direction, ref. TH 14
Extra-strong T rest, ref. TH 10a
Roller T rest for filling, ref. TH 10b
Extra-strong tool holder, ref. TH 14a
Face plate with 3 adjustable dogs, ref. TH 32
Driving chuck with 2 fingers, ref. TH 19
Screw chuck ref. TH 36b
3-jaw reversible, self-centring, chuck 55 mm, ref. TH 30
6-jaw reversible, self-centring chuck, ref. TH 30a
Universal, 6-jaw self-centring chuck 55 mm, ref. TH 30b
Ref. TH 40d Drawer 4
CHF 2'896.00
Extra-strong, swivelling slide rest, with covered slides, capacity 100 mm, ref. TH 13
Chuck 0 - 4 mm B 8 mm, ref. TH 31a
Chuck 0 - 4 mm 5 mm, ref. TH 31
Ref. TH 50 Watchmaker's Lathe, assortment
CHF 4'145.00
Lathe bed 220 mm, ref. TH 4a

Headstock ref. TH 6
Headstock with sliding tool, pulleys 12 - 20 mm, ref. TH 8
Tip-over T-rest reef. TH 10
Extra-strong T rest ref. TH 10a
18 chucks 2 mm dia shanks ref. TH 25
Tool for drilling and fitting pivots, ref. TH 27
Pivot-rolling disc, 18 notches, ref. TH 29
16 pivot chcucks ref. TH 37
With coffer N 1
Ref. TH 51 Watchmaker's lathe, assortment
CHF 3'235.00
Lathe bed 220 mm, ref. TH 4a

Headstock ref. TH 6
Headstock with sliding tool, pulleys 12 - 20 mm, ref. TH 8
Tip-over T-rest reef. TH 10
Extra-strong T rest ref. TH 10a
18 chucks 2 mm dia shanks ref. TH 25
16 pivot chcucks ref. TH 37
With coffer N 1

Ref. TH 60 Watchmaker's lathe, assortment
CHF 8'680.00
Lathe bed ref. TH 4

Headstock ref. TH 5
Tailstock ref. TH 6
Headstock with sliding tool, ref. TH 8
Tip-over T rest, ref. TH 10
Extra-strong T rest, ref. TH 10a
Roller T rest for filling, ref. TH 10
25 chucks body 8 mm, ref. TH 15a
Centred chuck holder, ref TH 24
Eccentric chuck holder, ref. TH 24a
18 arbors body 2 mm, ref. TH 25
Simple device for drilling and fitting pivots, ref. TH 27
Disc with 18 notches, ref. TH 29
15 pivot chucks, ref. TH 37
With coffer N 2

Watchmaker's Lathe - Accessories

Ref. TH 01 Lathe foot
CHF 140.00
With fastening screws and bolt
Ref. TH 01a Lathe foot
CHF 230.00
Adjustable lathe foot
Ref. TH 02 Lathe foot
CHF 230.00
With screws and bolt

For belt tightening device
Ref. TH 03 Hand flywheel
CHF 540.00
For fitting to vice

Example of use
Ref. TH 03b Belt tightening device
CHF 590.00
For lathe foot ref. TH 3b

Ref. TH 04 Lathe bed
CHF 360.00
260 mm
Ref. TH 04a Lathe bed
CHF 250.00
220 mm
Ref. TH 05 Headstock
CHF 1'350.00
Headstock with hardened steel shaft and double cone bearings, pulley with 12 divisions and indexing
finger. The shaft takes chucks of 8 mm.
Ref. TH 05-02 Brace for chuck B8
CHF 65.00
Brace for tailstock TH 05 for chuck B8
Ref. TH 06 Tailstock
CHF 580.00
This tailstock has a draw-in bar for tightening chucks and runners
CHF 940.00
Light pump tailstock with very lever for fine turning and drilling work.

CHF 815.00
Tailstock with special slide device, eccentric in all directions. Very useful for pivoting and hand turning
work. With 2 running pulleys of 12 - 20 mm. Takes Ref. TH 25 chucks and runners.
Ref. TH 08b Spindle
CHF 40.00
Spindle for Ref. TH 6 and TH 7
Ref. TH 08c Brace
CHF 35.00
Brace for Ref. TH 8a

Watchmaker's Lathe - Slide rest and turning tools

Ref. TH 09 Brace
CHF 95.00
To use with Ref. 13
Ref. TH 10 Tip-over T rest
CHF 195.00
With free clearance for the hand. The supports are of hardened steel
Ref. TH 10a T rest
CHF 45.00
Extra-strong
Ref. TH 10b Roller T rest
CHF 85.00
For filling
Ref. TH 10c Small T rest
CHF 45.00
Small T rest for ref. TH 10

Extra strong

Ref. TH 13 Slide rest
CHF 2'500.00
Extra-strong, swivelling slide rest, with covered slides. High precision. Capacity 100 mm with millimeter
vernier.
Ref. TH 14 Tool post
CHF 96.00
Very light tool post, movable in all directions
Ref. TH 14a Tool holder
CHF 258.00
Extra-strong tool holder. Recommended for special work.
Ref. TH 14b Turret
CHF 170.00
Turret only
Ref. TH 14c Graver
CHF 88.00
Graver only

Ref. TH 39 Graver kit
CHF 125.00
1 screw-driver
1 graver-holder
1 graver
Ref. TH 41 Spare graver
CHF 19.00
For ref. TH 39
Ref. TH 42 Graver-holder
CHF 99.00
Graver-holder alone with screw
Ref. TH 42-01 Screwdriver
CHF 10.00
Screwdriver alone
Ref. TH 42-02 Screw
CHF 4.00
Spare screw for ref. TH 39

Watchmaker's Lathe - Carriers

Ref. TH 20 6 steel carrier
CHF 180.00
Capacity:
6.00 - 4.50 mm
5.00 - 2.50 mm
4.00 - 2.00 mm
3.00 - 1.50 mm
2.00 - 0.80 mm
1.00 - 0.50 mm
Ref. TH 20-01 Steel carrier N1 - N6
CHF 30.00
Steel carrier alone

mm: N1 0.50 - 1.00, N2 0.80 - 2.00, N3 1.50 - 3.00, N4 2.00 - 4.00, N5 2.50 - 5.00,
N6 4.50 - 6.00
Ref. TH 20a 6 brass carriers
CHF 180.00
Capacity:
6.00 - 4.50 mm
5.00 - 2.50 mm
4.00 - 2.00 mm
3.00 - 1.50 mm
2.00 - 0.80 mm
1.00 - 0.50 mm
Ref. TH 20a-01 Brass carrier N1 - N6
CHF 30.00
Brass carrier alone

mm: N1 0.50 - 1.00, N2 0.80 - 2.00, N3 1.50 - 3.00, N4 2.00 - 4.00, N5 2.50 - 5.00,
N6 4.50 - 6.00

Ref. TH 38 12 small carrier
CHF 140.00
0.20 to 1.20 mm
With block
Ref. TH 38a Fixing appliance
CHF 110.00
For carriers
Ref. TH 38b Spare carriers N1 - N23
CHF 10.00
State hole diameter needed

mm: N1 0.20, N2 0.25, N3 0.30, N4 0.35, N5 0.40, N6 0.45, N7 0.50, N8
0.55, N9 0.60, N10 0.65, N11 0.70, N12 0.75, N13 0.80, N14 0.85, N15 0.90,
N16 0.95, N17 1.00, N18 1.05, N19 1.10, N20 1.15, N21 1.20, N22 1.25, N23
1.30

Watchmaker's Lathe - Pivot arbors

Ref. TH 24 Centred chuck holder
CHF 60.00
5 mm
Ref. TH 24a Eccentric chuck holder
CHF 65.00
5 mm
Ref. TH 25 18 arbors
CHF 270.00
2 mm
Ref. TH 25-01 Arbor N1 - N6
CHF 15.00
2 mm
B mm, C mm: N1 B 0.30, C 0.50, N2 B 0.40, C 0.60, N3 B 0.50, C 0.70, N4 B
0.60, C 0.80, N5 B 0.80, C 1.00, N6 B 1.00, C 1.20
Ref. TH 25-02 Arbor N1 - N6
CHF 15.00
2 mm
A mm, B mm, C mm: N1 A 0.15, B 0.30, C 0.50, N2 A 0.20, B 0.40, C 0.60, N3
A 0.25, B 0.50, C 0.70, N4 A 0.30, B 0.60, C 0.80, N5 A 0.35, B 0.80, C 1.00,
N6 A 0.45, B 1.00, C 1.20

Ref. TH 25-03 Point N1 - N3
CHF 15.00
2 mm
mm: N1 1.00, N2 2.00, N3 4.00
Ref. TH 25-04 Hollow point N1 - N3
CHF 15.00
2 mm
mm: N1 2.00, N2 3.00, N3 4.00
Ref. TH 37 15 pivot chucks
CHF 855.00
7 point chucks (0.05 / 0.10 / 0.15 / 0.20 / 0.30 / 0.40 / 0.50)

4 steel lanterns ( 4-16 / 16-40 / 22-45 / 50-100)
2 maillechor lanterns (22-45 / 50-100)
2 point chucks ( 50-100 / 100-200)
Ref. TH 37-01 Point chuck N1 - N7
CHF 51.00
Point chuck alone

mm: N1 0.05, N2 0.10, N3 0.15, N4 0.20, N5 0.30, N6 0.40, N7 0.50
Ref. TH 37-02 Point chuck N1 - N2
CHF 51.00
cones
mm: N1 0.50 - 1.00, N2 1.00 - 2.00

Ref. TH 37-03 Complete lantern N1 - N4
CHF 66.00
Complete lantern in steel

mm: N1 0.04 - 0.15, N2 0.16 - 0.40, N3 0.22 - 0.45, N4 0.50 - 1.00
Ref. TH 37-04 Complete lantern N1 - N2
CHF 66.00
Complete lantern in maillechor

mm: N1 0.22 - 0.45, N2 0.50 - 1.00
Ref. TH 37a-01 Point disc N1 - N7
CHF 38.00
Point disc alone

: N1 0.05, N2 0.10, N3 0.15, N4 0.20, N5 0.30, N6 0.40, N7 0.50
Ref. TH 37a-02 Point disc N1 - N2
CHF 38.00
Point disc 6-side

mm: N1 0.50 - 1.00, N2 1.00 - 2.00
Ref. TH 37a-03 Lantern N1 - N4
CHF 50.00
Lantern alone in steel

mm: N1 0.04 - 0.15, N2 0.16 - 0.40, N3 0.22 - 0.45, N4 0.50 - 1.00

Ref. TH 37a-04 Lantern N1 - N2
CHF 50.00
Lantern alone in maillechor

mm: N1 0.22 - 0.45, N2 0.50 - 1.00
Ref. TH 37b Arbor alone
CHF 13.00
For ref. TH 37 1-7/14/15
Ref. TH 37c Arbor alone N1 - N5
CHF 16.00
For ref. TH 37 8-13

inscription/einschreibung: N1 0.04 - 0.16, N2 0.16 - 0.40, N3 0.22 - 0.45, N4 0.50 - 1.00, N5 1.00
- 2.00

Watchmaker's Lathe - Various arbors

Ref. TH 21 4 wax chucks
CHF 144.00
Diameter: 6.60 / 10.00 / 15.00 / 20.00 mm
Ref. TH 21-01 Wax chuck N1 - N4
CHF 36.00
Wax chuck only

mm: N1 6.60, N2 10.00, N3 15.00, N4 20.00
Ref. TH 22 16 chucks and arbors
CHF 576.00
5 mm
Ref. TH 22-01 V arbor N1 - N2
CHF 36.00
5 mm
mm: N1 ~ 6.00, N2 ~ 10.00
Ref. TH 22-02 Flat arbor N1 - N3
CHF 36.00
5 mm
mm: N1 ~ 8.00, N2 ~ 14.00, N3 ~ 20.00

Ref. TH 22-03 Hollow point N1 - N4
CHF 36.00
5 mm
mm: N1 2.70, N2 4.00, N3 5.00, N4 6.00
Ref. TH 22-04 Preserve spindle hollow point N1 - N2
CHF 36.00
5 mm
mm: N1 2.50, N2 4.00
Ref. TH 22-05 Full point N1 - N2
CHF 36.00
5 mm
mm: N1 3.00, N2 5.00
Ref. TH 22-06 Broken point N1 - N2
CHF 36.00
5 mm
mm: N1 3.00, N2 4.00
Ref. TH 22-07 Slanting arbor
CHF 36.00
5 mm

Ref. TH 22a Chuck holder
CHF 36.00
Body B8
Ref. TH 34 Grinding wheel
CHF 75.00
Semi-fine, 80 mm
With ring and chuck
Ref. TH 34a Grinding wheel
CHF 75.00
Fine grinding wheel, 80 mm

With ring and chuck
Ref. TH 36 Chuck
CHF 55.00
For grinding wheel
Ref. TH 36a Screw chuck
CHF 50.00

Watchmaker's Lathe - Chucks and plates

Ref. TH 19 Driving chuck
CHF 85.00
With 2 fingers
Ref. TH 30 3-jaw chuck
CHF 1'200.00
3-jaw reversible, self-centring chuck, 55 mm

Strong-steel jaws
Ref. TH 30a Universal 6-jaw chuck
CHF 1'200.00
Universal 6-jaw self-centring chuck, 55 mm
Ref. TH 30b 6-jaw reversible chuck
CHF 1'370.00
6-jaw reversible, self-centring chuck
Ref. TH 31 Chuck
CHF 198.00
Chuck for tailstock ref. TH 7 and 11

Ref. TH 31a Chuck
CHF 198.00
Chuck for headstock ref. TH 5
Ref. TH 32 Face plate
CHF 670.00
Very accurate face plate with 3 adjustables dogs

With one strap
Ref. TH 33 Strap
CHF 50.00
For ref. TH 32
Ref. TH 33a Centring point
CHF 43.00
For ref. TH 32

Watchmaker's Lathe - Various apparatus

Ref. TH 08a Slide device
CHF 310.00
Special slide device, eccentric in all directions
Ref. TH 11 Lever pump attachment
CHF 420.00
For drilling and turning

3 split chucks
Same use as ref. TH 7
Ref. TH 11a Brace
CHF 38.00
For ref. TH 11
Ref. TH 11b Tightening clamp
CHF 40.00
For ref. TH 11
Ref. TH 11c Set of chucks
CHF 180.00
Set of 3 chucks P 5 mm for ref. TH 11
Ref. TH 11d Chuck N1 - N3
CHF 60.00
Chuck P 5 mm for ref. TH 11

mm: N1 1.00, N2 1.50, N3 2.00

Ref. TH 23 Eccentric slide device
CHF 280.00
With 2 pulleys 12 - 20 mm
Ref. TH 26 Apparatus for drilling and fitting
CHF 530.00
Complete apparatus for drilling and fitting pivots

The drilling discs have 18 chamfered holes, 0.15 to 1.40 mm with 6 points
2 centring tools
1 chuck P4,5 2.00 mm
Ref. TH 26c Centring tool
CHF 33.00
For ref. TH 26
Ref. TH 26d Centring tool
CHF 33.00
For ref. TH 26
Ref. TH 27 Device for drilling and fitting
CHF 480.00
Simple device for drilling and fitting pivots

4 centring tools
Ref. TH 27a Centring tool
CHF 28.00
For ref. TH 27
Ref. TH 27b Centring tool
CHF 28.00
For ref. TH 27

Ref. TH 27c Point
CHF 35.00
For ref. TH 27
Ref. TH 27d Point
CHF 35.00
For ref. TH 27
Ref. TH 28 Drilling disc
CHF 190.00
With 10 large chamfered holes
Ref. TH 29 Steel wheel
CHF 430.00
With 18 notches, for rolling pivots from 0.15 to 1.40 mm
Ref. TH 29a Bronze wheel
CHF 440.00
With 18 notches, for burnishing pivots from 0.15 to 1.40 mm

Ref. TH 43 Chuck
CHF 53.00
Chuck for ref. TH 8a and 23

Watchmaker's Lathe - Motor

Ref. TH 40-100 Command tool
CHF 850.00
With 2 m cabel and 6+T input for ref. TH 40-101
Ref. TH 40-101 Motor
CHF 2'150.00
With convertisser and command station with 3 m cabel 220 V
Ref. TH 40-102 Autotransformer
CHF 260.00
Carriable autotransformer
Ref. TH 40-103 Vice adaptator
Ref. TH 40-104 Motor
CHF 123.00
CHF 2'450.00
Whole engine motor, inverter and control station with 3m of cable 220 V and plug into his cabinett

Ref. TH 40-105 Case
CHF 300.00
Case for motor Rf. TH 40-104

Watchmaker's Lathe - Chucks B8

Ref. TH 15 Set of chucks B8
CHF 1'895.00
Set of 20 chucks B8
0.40 / 0.50 / 0.60 / 0.80 / 1.00 / 1.20 1.40 / 1.60 / 1.80 / 2.00 / 2.20 / 2.40 / 2.60 / 2.80 / 3.00 / 3.20 /
3.50 / 4.00 / 4.50 / 5.00 mm
Ref. TH 15A Set of chucks B8
CHF 2'700.00
Set of 25 chucks B8
0.40 / 0.50 / 0.60 / 0.70 / 0.80 / 0.90 / 1.00 / 1.20 / 1.40 / 1.50 / 1.60 / 1.80 / 2.00 / 2.20 / 2.50 / 2.80 /
3.00 / 3.20 / 3.50 / 3.80 / 4.00 / 4.20 / 4.50 / 4.80 / 5.00 mm
Ref. TH 15B Set of chucks B8
CHF 3'235.00
Set of 30 chucks B8
0.40 / 0.50 / 0.60 / 0.70 / 0.80 / 0.90 / 1.00 / 1.10 / 1.20 / 1.40 / 1.50 / 1.60 / 1.70 / 1.80 / 2.00 / 2.20 /
2.50 / 2.80 / 3.00 / 3.20 / 3.50 / 3.80 / 4.00 / 4.20 / 4.50 / 4.80 / 5.00 / 5.20 / 5.50 / 5.80 / 6.00 mm
Ref. TH 15C Set of chucks B8
CHF 3'596.00
Set of 34 chucks B8
0.40 / 0.50 / 0.60 / 0.70 / 0.80 / 0.90 / 1.00 / 1.10 / 1.20 / 1.30 / 1.40 / 1.50 / 1.60 / 1.70 / 1.80 / 1.90 /
2.00 / 2.10 / 2.20 / 2.50 / 2.80 / 3.00 / 3.20 / 3.50 / 3.80 / 4.00 / 4.20 / 4.50 / 4.80 / 5.00 / 5.20 / 5.50 /
5.80 / 6.00 mm
Ref. TH 15D Set of chucks B8
CHF 6'990.00
Set of 60 chucks B8
0.40 / 0.50 / 0.60 / 0.70 / 0.80 / 0.90 / 1.00 / 1.10 / 1.20 / 1.30 / 1.40 / 1.50 / 1.60 / 1.70 / 1.80 / 1.90 /
2.00 / 2.10 / 2.20 / 2.30 / 2.40 / 2.50 / 2.60 / 2.70 / 2.80 / 2.90 / 3.00 / 3.10 / 3.20 / 3.30 / 3.40 / 3.50 /
3.60 / 3.70 / 3.80 / 3.90 / 4.00 / 4.10 / 4.20 / 4.30 / 4.40 / 4.50 / 4.60 / 4.70 / 4.80 / 4.90 / 5.00 / 5.10 /
5.20 / 5.30 / 5.40 / 5.50 / 5.60 / 5.70 / 5.80 / 5.90 / 6.00 / 6.20 / 6.50 / 7.00 mm
Ref. TH 15E Chucks B8 N1 - N8 (0.25 - 0.95 mm)
CHF 1'232.00
Set of 8 specials chucks B8

0.25 / 0.35 / 0.45 / 0.55 / 0.65 / 0.75 / 0.85 / 0.95 mm
mm: N1 0.25, N2 0.35, N3 0.45, N4 0.55, N5 0.65, N6 0.75, N7 0.85, N8
0.95

Ref. TH 15F-01 Chuck B8 N1 - N7 (0.30 - 0.90 mm)
CHF 154.00
Chuck B8 only
mm: N1 0.30, N2 0.40, N3 0.50, N4 0.60, N5 0.70, N6 0.80, N7 0.90
CHF 99.00
Chuck B8 only
mm: N1 1.00, N2 1.10, N3 1.20, N4 1.30, N5 1.40, N6 1.50, N7 1.60, N8
1.70, N9 1.80, N10 1.90
Ref. TH 15F-03 Chuck B8 N1 - N12 (2.00 - 3.00, 3.50 mm)
CHF 64.00
Chuck B8 only
mm: N1 2.00, N2 2.10, N3 2.20, N4 2.30, N5 2.40, N6 2.50, N7 2.60, N8
2.70, N9 2.80, N10 2.90, N11 3.00, N12 3.50
CHF 164.00
Chuck B8 only
mm: N1 3.10, N2 3.20, N3 3.30, N4 3.40, N5 3.60, N6 3.70, N7 3.80, N8
3.90
CHF 154.00
Chuck B8 only
mm: N1 4.10, N2 4.20, N3 4.30, N4 4.40, N5 4.60, N6 4.70, N7 4.80, N8
4.90, N9 5.10, N10 5.20, N11 5.30, N12 5.40, N13 5.60, N14 5.70, N15 5.80,
N16 5.90, N17 6.10, N18 6.20, N19 6.30, N20 6.40, N21 6.60, N22 6.70, N23
6.80, N24 6.90, N25 7.10, N26 7.20, N27 7.30, N28 7.40, N29 7.60, N30 7.70,
N31 7.80, N32 7.90
CHF 54.00
Chuck B8 only
mm: N1 4.00, N2 4.50, N3 5.00, N4 5.50, N5 6.00, N6 6.50, N7 7.00, N8
7.50, N9 8.00
Ref. TH 16 5 hollow chucks B8
CHF 300.00
Capacity: 8 mm
9 mm
10 mm
11 mm
12 mm

Ref. TH 16-01 Hollow chuck B8 N1 - N5
CHF 60.00
Hollow chuck alone

mm: N1 8.00, N2 9.00, N3 10.00, N4 11.00, N5 12.00
Ref. TH 17 4 step collets B8
CHF 260.00
Capacity: 5.50 - 21.50 mm

6.00 - 22.00 mm
6.50 - 22.50 mm
7.00 - 23.00 mm
Ref. TH 17-01 Step collet B8 N1 - N4
CHF 65.00
Step collet alone

mm: N1 5.50 - 21.50, N2 6.00 - 22.00, N3 6.50 - 22.50, N4 7.00 - 23.00
Ref. TH 18 12 funnel collets B8
CHF 693.00
12 special funnel collets, capacity:

5.50 - 6.50 - 7.50 mm
6.00 - 7.00 - 8.00 mm
8.50 - 9.50 - 10.50 mm
9.00 - 10.00 - 11.00 mm
11.50 - 12.50 - 13.50 mm
12.00 - 13.00 - 14.00 mm
14.50 - 15.50 - 16.50 mm
15.00 - 16.00 - 17.00 mm
17.50 - 18.50 - 19.50 mm
18.00 - 19.00 - 20.00 mm
20.50 - 21.50 - 22.50 mm
21.00 - 22.00 - 23.00 mm

Ref. TH 18-01 Funnel collet B8 N1 - N12
CHF 57.80
Special funnel collet alone

mm: N1 5.50 - 6.50 - 7.50, N2 6.00 - 7.00 - 8.00, N3 8.50 - 9.50 - 10.50, N4 9.00 - 10.00
- 11.00, N5 11.50 - 12.50 - 13.50, N6 12.00 - 13.00 - 14.00, N7 14.50 - 15.50 - 16.50, N8
15.00 - 16.00 - 17.00, N9 17.50 - 18.50 - 19.50, N10 18.00 - 19.00 - 20.00, N11 20.50 - 21.50 22.50, N12 21.00 - 22.00 - 23.00

Watchmaker's Lathe - Chucks P4,5

Ref. H 550-01 Chuck P 4.5 (0.30 - 0.90 mm)
CHF 160.00
Chuck P 4.5 for ref. H 550 0.30 mm 0.90 mm

For intermediate dimensions price on application
mm: N1 0.30, N2 0.50, N3 0.60, N4 0.70, N5 0.80, N6 0.90
Ref. H 550-01-02 Chuck P 4.5 (0.40 mm)
CHF 260.00
Chuck P 4.5 for ref. H 550 0.40 mm
Ref. H 550-02 Chuck P 4.5 (1.00 - 1.90 mm)
CHF 105.00
Chuck P 4.5 for ref. H 550 1.00 mm 1.90 mm

mm: N1 1.00, N2 1.10, N3 1.20, N4 1.30, N5 1.40, N6 1.50, N7 1.60, N8
1.70, N9 1.80, N10 1.90
Ref. H 550-03 Chuck P 4.5 (2.00 - 3.00, 3.50 mm)
CHF 70.00
Chuck P 4.5 for ref. H 550 2.00 mm 3.00 mm and 3.50 mm

mm: N1 2.00, N2 2.10, N3 2.20, N4 2.30, N5 2.40, N6 2.50, N7 2.60, N8
2.70, N9 2.80, N10 2.90, N11 3.00, N12 3.50

Ref. H 550-04 Chuck P 4.5 (4.00, 4.50 mm)
CHF 60.00
Chuck P 4.5 for ref. H 550 4.00 mm et 4.50 mm

mm: N1 4.00, N2 4.50

Jewellling, Setting, staking tools - Jewelling tools

Ref. PO 61-01-03 Jewelling tool "pas fin", spindle hole 3.00
mm
CHF 490.00
Jewelling tool's with micrometric screw for rectifying endshakes

Opening 25 mm
Total height 120 mm
Base 80 x 45 mm
Table hole: 4 mm
Spindle with "pas fin": 3.00 mm
Ref. PO 61-01-04 Jewelling tool "pas fin", spindle hole 4.00

mm
CHF 490.00

Opening 25 mm
Total height 120 mm
Base 80 x 45 mm
Table hole: 4 mm
Spindle with "pas fin": 4.00 mm
Ref. PO 61-03 Jewelling tool, spindle hole 3.00 mm
CHF 370.00

Opening 25 mm
Total height 120 mm
Base 80 x 45 mm
Table hole: 4.00 mm
Spindle hole: 3.00 mm
CHF 370.00

Opening 25 mm
Total height 120 mm
Base 80 x 45 mm
Table hole: 4.00 mm
Spindle hole: 4.00 mm

Ref. PO 63-01 Jewelling tool, choose of spindle and table
CHF 475.00

Opening 30 mm
Total height 125 mm
Base 90 x 50 mm
Spindle and table: customer's choice
broche/spindle: 3.00 mm, 4.00 mm
CHF 395.00

Opening 30 mm
Total height 125 mm
Base 90 x 50 mm
Table hole: 4 mm
Spindle: 3 mm
CHF 395.00

Opening 30 mm
Total height 125 mm
Base 90 x 50 mm
Table hole: 4 mm
Spindle: 4 mm

Jewellling, Setting, staking tools - Jewelling tools in boxes

Ref. H 200 Jewelling tool's box
CHF 1'174.00
1 box with drawer

1 setting tool ref. PO 61
1 spindle ref. H 550
1 set of 15 cutting broaches flutes ref. H 500 3.00 mm oder 4.00 mm, on request
: 3.00 mm, 4.00 mm
Ref. H 200-01 Jewelling tool's box
CHF 1'364.00
1 box with drawer

1 set of 15 cutting broaches flutes ref. H 500
1 assortment ref. AS 1 3.00 mm oder 4.00 mm, on request
: 3.00 mm, 4.00 mm
CHF 1'724.00
1 box with drawer

: 3.00 mm, 4.00 mm
CHF 1'484.00
1 box with drawer

: 3.00 mm, 4.00 mm

CHF 1'890.00
1 box with drawer

: 3.00 mm, 4.00 mm

Jewellling, Setting, staking tools - Accessories

Ref. PO 61-02 Spindle
CHF 61.00
For ref. PO 61 / 61-1

: 3.00 mm, 4.00 mm
Ref. PO 61-05 Screw and bolder
CHF 74.00
For ref. PO 61 / 61-1
Ref. PO 61-06 Standart exchange
CHF 185.00
For ref. PO 61 / 61-1
Ref. PO 63-02 Spindle 63 mm without furrow
CHF 68.00
Spindle 63 mm without furrow. For ref. TH 63

: 3.00 mm, 4.00 mm
Ref. PO 63-02-01 Spindle 63 mm with furrow
CHF 75.00
Spindle 63 mm with furrow. For Ref. PO 63

: 3.00 mm, 4.00 mm
Ref. PO 63-05 Screws and bolt
CHF 94.00
For ref. PO 63 / 75

Ref. PO 63-06 "Levier"
CHF 60.00
For ref. PO 63
Ref. PO 63-07 Spring
CHF 4.60
For ref. PO 52 / 63 / 75
Ref. PO 63-09 Spindle 68 mm with furrow
CHF 75.00

: 3.00 mm, 4.00 mm
Ref. PO 63-10 Spindle 73 mm with furrow
CHF 75.00

: 3.00 mm, 4.00 mm

Jewellling, Setting, staking tools - Setting tools

Ref. PO 51 Setting tool
CHF 425.00
Setting tool for hands, single model with 2 spindles
CHF 595.00
Setting tool for hand with 2 oscillating spindle, basis 31 mm
CHF 490.00
For setting "aiguilles"

With 3 free spindle
Arbor 1.35 / 0.95 / 0.30 mm
Ref. PO 53-01 Setting tool
CHF 550.00
To set "aiguilles"
With 2 free spindle, 1 "orienteted" spindle
Arbors 1.35 / 0.95 / 0.30 mm

Ref. PO 53-02 Setting tool
CHF 640.00
To set "aiguilles" with 3 spindles

2 free spindles, 1 "orinteted" spindle
Arbors 1.35 / 0.95 and ref. PO 53-17
Ref. PO 53-04 Setting tool with 4 spindles
CHF 610.00

4 free spindles
Ref. PO 53-05 Setting tool with 4 spindles
CHF 650.00

3 free spindles, 1 "orinteted" spindle
Ref. PS 51-05 Micrometric setting tool
CHF 555.00
Micrometric setting tool with tabl 50.50 x 80.00 mm and set of guide screws 2.70 mm, 3.00 mm, 3.50
mm, 4.00 mm.

Jewellling, Setting, staking tools - Pushers and anvils for hands

Ref. AS 51-10-01 Pusher in steel only N1 - N10
CHF 12.50
Pusher in steel 3.00 mm

mm: N1 0.25, N2 0.40, N3 0.60, N4 0.80, N5 1.00, N6 1.20, N7 1.40, N8
1.60, N9 1.80, N10 2.00
Ref. AS 51-10-02 Pusher in steel and delrin only N1 - N10
CHF 17.00
Pusher in steel and delrin 3.00 mm

mm: N1 0.25, N2 0.40, N3 0.60, N4 0.80, N5 1.00, N6 1.20, N7 1.40, N8
1.60, N9 1.80, N10 2.00
Ref. PO 52-05 Embout N1 - N28
CHF 25.00
For spindle ref. PO 52-1 / 52-2

mm: N1 0.40, N2 0.50, N3 0.60, N4 0.70, N5 0.80, N6 0.90, N7 1.00, N8
1.10, N9 1.20, N10 1.30, N11 1.40, N12 1.50, N13 1.60, N14 1.70, N15 1.80,
N16 1.90, N17 2.00, N18 2.10, N19 2.20, N20 2.30, N21 2.40, N22 2.50, N23
2.60, N24 2.70, N25 2.80, N26 2.90, N27 3.00
Ref. PO 53-01-H Arbor for hour
CHF 19.00
Standard arbor 1.35 mm for ref. PO 53 / 53-1 / 53-2
Ref. PO 53-01-M Arbor for minute
CHF 19.00
Ref. PO 53-01-S Arbor for second
CHF 19.00

Ref. PO 53-12 Arbor with hole N1 - N21
CHF 31.00
Hollow arbor for Ref. PO 53

int. mm, ext. mm: N1 0.70, 1.30, N2 0.70, 1.50, N3 0.70, 1.70, N4 0.70,
2.00, N5 0.90, 1.70, N6 0.90, 2.00, N7 0.90, 2.20, N8 1.00, 1.60, N9 1.20,
1.80, N10 1.20, 2.00, N11 1.20, 2.50, N12 1.30, 2.20, N13 1.50, 2.00, N14
1.50, 2.40, N15 1.50, 2.80, N16 1.80, 3.00, N17 2.00, 2.80, N18 2.00, 3.20,
N19 2.50, 3.20, N20 2.50, 3.50, N21 2.50, 4.00
Ref. PO 53-13 Arbor full N1 - N38
CHF 19.00
Full arbor for Ref. PO 53

mm: N1 0.30, N2 0.40, N3 0.50, N4 0.60, N5 0.70, N6 0.80, N7 0.90, N8
1.00, N9 1.10, N10 1.20, N11 1.30, N12 1.40, N13 1.50, N14 1.60, N15 1.70,
N16 1.80, N17 1.90, N18 2.00, N19 2.10, N20 2.20, N21 2.30, N22 2.40, N23
2.50, N24 2.60, N25 2.70, N26 2.80, N27 2.90, N28 3.00, N29 3.10, N30 3.20,
N31 3.30, N32 3.40, N33 3.50, N34 3.60, N35 3.70, N36 3.80, N37 3.90, N38
4.00
Ref. PO 53-14 Arbor in nylon N1 - N21
CHF 31.00
Nylon arbor for Ref. PO 53

int. mm, ext. mm: N1 0.70, 1.30, N2 0.70, 1.50, N3 0.70, 1.70, N4 0.70,
2.00, N5 0.90, 1.70, N6 0.90, 2.00, N7 0.90, 2.20, N8 1.00, 1.60, N9 1.20,
1.80, N10 1.20, 2.00, N11 1.20, 2.50, N12 1.30, 2.20, N13 1.50, 2.00, N14
1.50, 2.40, N15 1.50, 2.80, N16 1.80, 3.00, N17 2.00, 2.80, N18 2.00, 3.20,
N19 2.50, 3.20, N20 2.50, 3.50, N21 2.50, 4.00
Ref. PO 53-15 Nylon arbor full N1 - N38
CHF 19.00
Nylon arbor without hole for Ref. PO 53

mm: N1 0.30, N2 0.40, N3 0.50, N4 0.60, N5 0.70, N6 0.80, N7 0.90, N8
1.00, N9 1.10, N10 1.20, N11 1.30, N12 1.40, N13 1.50, N14 1.60, N15 1.70,
N16 1.80, N17 1.90, N18 2.00, N19 2.10, N20 2.20, N21 2.30, N22 2.40, N23
2.50, N24 2.60, N25 2.70, N26 2.80, N27 2.90, N28 3.00, N29 3.10, N30 3.20,
N31 3.30, N32 3.40, N33 3.50, N34 3.60, N35 3.70, N36 3.80, N37 3.90, N38
4.00
Ref. PO 53-17 Arbor
CHF 96.00
Eccentric arbor 7.50 mm

Ref. PO 53-18 Arbor
CHF 116.00
Eccentric arbor 10.00 mm


Ref. PO 52-02 Oscillating spindle N1 - N2 (1.00, 1.20 mm)
CHF 55.00
For ref. PO 52
mm: N1 1.00, N2 1.20
CHF 39.00
Simple model, not adjustable
Ref. PO 52-04 Oscillating spindle N1 - N25 (0.40 - 3.00 mm)
CHF 55.00
For ref. PO 52
mm: N1 0.40, N2 0.50, N3 0.60, N4 0.70, N5 0.80, N6 0.90, N7 1.10, N8
1.30, N9 1.40, N10 1.50, N11 1.60, N12 1.70, N13 1.80, N14 1.90, N15 2.00,
N16 2.10, N17 2.20, N18 2.30, N19 2.40, N20 2.50, N21 2.60, N22 2.70, N23
2.80, N24 2.90, N25 3.00
CHF 67.00
Spindle
Ref. PO 52-10 Pusher N1 - N3
CHF 6.30
For spindle ref. PO 52-1 / 52-2 / 52-3 / 52-4 / 52-6

Couleur/Farbe/Color: N1 Noir - Schwarz - Black, N2 Blanc - Weiss - White, N3 Rouge - Rot - Red
Ref. PO 52-12 Table to set counter
CHF 28.00
Table indexer les compteurs Ref. PO 52-12

Base 31.00 mm
Pivot 3.00 mm

CHF 24.00
Pour rf. PO 53
CHF 31.00
Pour rf. PO 53

Jewellling, Setting, staking tools - Staking and milling tools

Ref. PR 100 Staking tool to rivet
Ref. PR 110 Staking tool in his box
CHF 680.00
CHF 1'844.00
Coffret complet pour river comprenant:

7 rivoirs bille Ref. Riv 05B
12 rivoirs trou face bombe sans conserve pivots Ref. Riv 06
12 rivoirs trou face bombe et conserve pivots Ref. Riv 07
12 rivoirs trou face plate sans conserve pivots Ref. Riv 08
8 rivoirs trou face plate et conserve pivots Ref. Riv 09
10 rivoirs plats trou conique Ref. Riv 10
10 rivoirs cylindriques face bombe Ref. Riv 11
10 rivoirs cylindriques face plate Ref. Riv 12
3 rivoirs trous face plate et dgagement Ref. Riv 13
2 rivoirs pointe conique Ref. Riv 15
2 pointes fraiser coniques Ref. Riv 16
1 rivoir marteler Ref. Riv 17
1 jeu de 15 alsoirs Ref. H 500
1 potence Ref. PR 110-05
1 table rectangulaire Ref. PS 51-5-06
1 table ronde Ref. PR 110-30
1 broche Ref. H 550
1 pince P 4.5 2.00 mm Ref. H 550-4
1 broche river Ref. PR 100-21
4 vis de centrage Ref. PS 51-5-08
1 coffret Ref. PR 100
Ref. PR 110-10 Staking tool
CHF 353.00
Staking tool with spindle

Tool Ref. PR 110-05
Spindle Ref. PR 100-21

CHF 463.00
Staking tool with table and spindle.

Tool Ref. PR 110-05
Table Ref. PR 110-30
Spindle Ref. PR 100-21
CHF 600.00
Staking tool with table and 2 spindle

Tool Ref. PR 110-05
Table Ref. PR 110-30
Staking spindle Ref. PR 100-21
Spindle Ref. H 550
Chuck P4,5 2.00 mm Ref. H 550-03 N
Ref. PR 80 Staking tool to rivet
CHF 650.00
Ref. PS 51-02 Staking tool
CHF 441.00
Staking tool with adjustable weight

Spindel 8 mm
Base and hole
base: 8 mm, 10 mm, 12 mm, 14 mm

Ref. PS 51-03 Staking tool for mill
CHF 484.00
With table, spindel and chuck P4.5 3.00 mm
Ref. PS 75-02 Staking tool
CHF 920.00
Staking tool with adjustable weight

Spindle 14 mm
Hole 6 mm
Base 14 mm


Ref. H 550 Spindle
CHF 69.00
Broche 8 mm pour pince P 4.5
Ref. H 560 Table
CHF 23.00
Table 35 mm pour rf. PO 63
Ref. PR 100-21 Spindle for staking
CHF 73.00
Spindle for staking tool
Ref. PR 110-05 Base only
CHF 280.00
Base only, for staking
Ref. PR 110-30 Round table for staking
CHF 110.00
Round table for staking with mobile foot.

Ref. PR 110-C01 Box only
CHF 100.00
Box only for staking tool.
Ref. PS 51-05-06 Table
CHF 88.00
Table for setting tool ref. PS 5150.50 x 80.00 mm of the hole: 4.00 mm
Ref. PS 51-05-08 Set of guide's screw
CHF 20.00
Set of guide's screw for table Ref. PS 51-05-06

2.70 mm / 3.00 mm / 3.50 mm / 4.00 mm
Ref. PS 51-05-09 Guide screw N1 - N4
CHF 5.00
Guide screw for table ref. PS 51-5-06

A mm: N1 2.70, N2 3.00, N3 3.50, N4 4.00

Jewellling, Setting, staking tools - Cutting broaches and reamers

Ref. H 500 Cutting broaches flutes
CHF 140.00
Jeu de 15 alsoirs
0.69 / 0.79 / 0.89 / 0.99 / 1.09 / 1.19 / 1.29 / 1.39 /
1.49 / 1.59 / 1.79 / 1.99 / 2.22 / 2.59 / 2.99 mm
Ref. H 500-01 Cutting broaches flute N1 - N15
CHF 8.00
Cutting broaches flute only

mm: N1 0.69, N2 0.79, N3 0.89, N4 0.99, N5 1.09, N6 1.19, N7 1.29, N8
1.39, N9 1.49, N10 1.59, N11 1.79, N12 1.99, N13 2.29, N14 2.59, N15 2.99
Ref. H 510 Chamfered reamers
CHF 160.00
Jeu de 15 quarrissoirs 7 pans

0.69 / 0.79 / 0.89 / 0.99 / 1.09 / 1.19 / 1.29 / 1.39 /
1.49 / 1.59 / 1.79 / 1.99 / 2.22 / 2.59 / 2.99 mm
Ref. H 510-01 Chamfered reamer N1 - N15
CHF 9.00
Chamfered reamer only

mm: N1 0.68, N2 0.78, N3 0.88, N4 0.98, N5 1.08, N6 1.18, N7 1.28, N8
1.38, N9 1.48, N10 1.58, N11 1.78, N12 1.98, N13 2.28, N14 2.58, N15 2.98

Jewellling, Setting, staking tools - Chucks P 4,5

Ref. H 550-01 Chuck P4,5 N1 - N6 (0.30 - 0.90 mm)
CHF 160.00
Chuck P 4.5 for ref. H 550

For the intermediate diameter; price on request
mm: N1 0.30, N2 0.50, N3 0.60, N4 0.70, N5 0.80, N6 0.90
Ref. H 550-01-02 Chuck P4,5 (0.40 mm)
CHF 260.00
Chuck P 4.5 for ref. H 550 0.40 mm
Ref. H 550-02 Chuck P 4,5 N1 - N10 (1.00 - 1.90 mm )
CHF 105.00

mm: N1 1.00, N2 1.10, N3 1.20, N4 1.30, N5 1.40, N6 1.50, N7 1.60, N8
1.70, N9 1.80, N10 1.90
Ref. H 550-03 Chuck P4,5 N1 - N12 (2.00 - 3.00, 3.50 mm)
CHF 70.00

mm: N1 2.00, N2 2.10, N3 2.20, N4 2.30, N5 2.40, N6 2.50, N7 2.60, N8
2.70, N9 2.80, N10 2.90, N11 3.00, N12 3.50

Ref. H 550-04 Chuck P4,5 N1 - N2 (4.00, 4.50 mm )
CHF 60.00

mm: N1 4.00, N2 4.50

Jewellling, Setting, staking tools - Staking hammer with marble

Ref. RIV 05 B Staking hammer with marble N1 - N8
CHF 30.00
Staking hammer with marble in hard steel 0.50 mm 4.00 mm

mm: N1 0.50, N2 1.00, N3 1.50, N4 2.00, N5 2.50, N6 3.00, N7 3.50, N8
4.00

Jewellling, Setting, staking tools - Staking hammer standard

Ref. RIV 06 Staking hammer with hole and bombed face N1
- N12
CHF 8.00
Staking hammer with hole and bombed face without pivot case
mm: N1 0.30, N2 0.35, N3 0.40, N4 0.45, N5 0.50, N6 0.55, N7 0.60, N8
0.70, N9 0.80, N10 0.90, N11 1.00, N12 1.20
Ref. RIV 07 Staking hammer with hole and bombed face N1

- N12
CHF 8.00
Staking hammer with hole and bombed face with pivot case
mm: N1 0.30, N2 0.35, N3 0.40, N4 0.45, N5 0.50, N6 0.55, N7 0.60, N8
0.70, N9 0.80, N10 0.90, N11 1.00, N12 1.20
Ref. RIV 08 Staking hammer with hole and flat face N1 N12
CHF 8.00
Staking hammer with hole and flat face without pivot case
mm: N1 0.30, N2 0.35, N3 0.40, N4 0.45, N5 0.50, N6 0.55, N7 0.60, N8
0.70, N9 0.80, N10 0.90, N11 1.00, N12 1.20
Ref. RIV 09 Staking hammer with hole and flat face N1 N12
CHF 8.00
Staking hammer with hole and flat face with pivot case
mm: N1 0.30, N2 0.35, N3 0.40, N4 0.45, N5 0.50, N6 0.55, N7 0.60, N8
0.70, N9 0.80, N10 0.90, N11 1.00, N12 1.20
Ref. RIV 10 Staking hammer with conical hole and flat face
N1 - N10
CHF 8.00
Staking hammer with conical hole and flat face

mm: N1 0.30, N2 0.40, N3 0.50, N4 0.60, N5 0.70, N6 0.80, N7 1.00, N8
1.20, N9 1.40, N10 1.60

Ref. RIV 11 Staking hammer with cylindric pin and bombed

face N1 - N10
CHF 8.00
Staking hammer with cylindric pin and bombed face

mm: N1 1.00, N2 1.20, N3 1.40, N4 1.60, N5 1.80, N6 2.00, N7 2.20, N8
2.40, N9 2.60, N10 3.00
Ref. RIV 12 Staking hammer with cylindric pin and flat face
N1 - N10
CHF 8.00
Staking hammer with cylindric pin and flat face

mm: N1 0.40, N2 0.50, N3 0.60, N4 0.80, N5 1.00, N6 1.20, N7 1.50, N8
2.00, N9 2.50, N10 3.00
Ref. RIV 13 Staking hammer with opening and flat face N1 N3
CHF 12.00
Staking hammer with opening and flat face

mm: Ref. Riv.13 N1 0.85, Ref. Riv.13 N2 1.00, Ref. Riv.13 N3 1.20, N1 0.85, N2
1.00, N3 1.20
Ref. RIV 15 Staking hammer with conical point N1 - N2
CHF 10.00
Staking hammer with conical point 40 and 60

Angle/Winkel: N1 40, N2 60
Ref. RIV 16 Conical point to mill N1 - N2
CHF 12.00
Conical point to mill 40 and 60

Angle/Winkel: N1 40, N2 60
Ref. RIV 17 Staking point to hammer
CHF 12.00
Staking point to hammer

Jewellling, Setting, staking tools - Setting tools for locks

Ref. PV 51 Setting tool for lock
CHF 940.00
Setting tool to open and close locks

With 2 spindles and 2 support for cal. 2892 and cal. 7750 spindle 12 mm base 12 mm


Ref. PV 51-01 Spindle and support
CHF 340.00
Spindle and support for ref. PV 51, cal. 7750
Ref. PV 51-01-01 Spindle
CHF 235.00
Spindle for ref. PV 51, cal. 7750
Ref. PV 51-01-02 Support
CHF 105.00
Support for ref. PV 51, cal. 7750
Ref. PV 51-02 Spindle and support
CHF 340.00
Spindle and support for ref. PV 51, cal. 2892
Ref. PV 51-02-01 Spindle
CHF 235.00
Spindle for ref. PV 51, cal. 2892

Ref. PV 51-02-02 Support
CHF 105.00
Support for ref. PV 51, cal. 2892
Ref. PV 51-03 Setting tool only
CHF 260.00
Setting tool only

Jewellling, Setting, staking tools - Other setting tools

Ref. PO 300 Powerful press with adjustable head
CHF 1'000.00
Powerful press with adjustable head

Total height: 350 mm
Column height: 300 mm
Table: 150 mm x 100 mm
Spindle: 25 mm Alsage: 10 mm
Void max height: 240 mm
Adjust the height every: 30 mm
Spindle way: 70 mm
Table slot: 12 x 18 mm ht 15 mm
Ref. PO 70 Staking tool
CHF 660.00
Potence levier, grand modle avec bague d arrt

Hauteur totale 200 mm
Longueur du bti 140 mm
Dgagement 50 mm
Table
Broche
ajustement table: 10 mm, 12 mm, 14 mm
Ref. PO 70-01 Staking tool
CHF 790.00
Staking tool, large type, with stop ring

Total height 200 mm
Lenght of frame 140 mm
Opening 50 mm
With table and spindle
With tools
ajustement table: 10 mm, 12 mm, 14 mm
CHF 850.00
Grand modle avec bute vis micromtrique

Dgagement 50 mm
Table: ajustement 14 mm
Broche: trou 6 mm

CHF 1'250.00
Potence levier grand modle avec bute vis micromtrique

Dgagement 50 mm
Table: ajustement 14 mm
Broche: trou 6 mm
Ref. PS 51-01 Setting tool

Without spindle and support Hole:
mmOther on demand
CHF 260.00
height 8.00 mm
Ref. PS 63 Staking tool
base 10.00
CHF 240.00
Potence fermer les fonds, sans posage standard


Ref. PO 300-25 Table for Rf. PO 300
CHF 180.00
Count of positioning for Ref. PO 300
CHF 130.00
For ref. PO 75
Ref. PS 63-01 Support N1 - N5
CHF 35.00
Support for ref. PS 63

mm: N1 20.00, N2 25.00, N3 29.00, N4 32.00, N5 35.00

Jewellling, Setting, staking tools - Set of pushers and anvils

Ref. AS 01-01 Box
CHF 45.00
Box of assortment 1, for pump pushers and anvils
Ref. AS 01-03 Assortment pump pushers 3.00 mm and

anvils
CHF 190.00
Assortment of 8 pump pushers 3.00 mm and 3 anvils

anvils
CHF 190.00
Ref. AS 02-01 Box
CHF 70.00

anvils
CHF 550.00
Assortment of 15 pump pushers 3.00 mm, 15 anvils

1 set of 1 anvil and 1 forkstaff pusher
1 set of 1 anvil and 1 guard spin pusher

anvils
CHF 550.00
Assortment of 15 pump pushers 4.00 mm, 15 anvils

1 set of 1 anvil and 1 forkstaff pusher
1 set of 1 anvil and 1 guard spin pusher

Ref. AS 03-01 Box
CHF 65.00

anvils
CHF 310.00

anvils
CHF 310.00
Ref. AS 04-01 Box
CHF 88.00

anvils
CHF 715.00
Complete assortment of 24 pump pushers 3.00 mm and 24 anvils


anvils
CHF 715.00
Complete assortment of 24 pump pushers 4.00 mm and 24 anvils
Ref. AS 05-01 Empty box for AS 05
CHF 30.00
Empty box for pushers and anvils for Incabloc
Ref. AS 05-03 Set of pushers and anvil for Incabloc 3.00 mm
CHF 154.00
Ref. AS 05-04 Set of pushers and anvils for Incabloc 4 mm
CHF 154.00
Ref. AS 51-10 Set of pushers for hands
CHF 350.00
Set of pushers 3.00 mm which is used with setting-tool ref. PS 51-5 and contains:10 pushers in steel
(mm) 0.25 / 0.40 / 0.60 / 0.80 / 1.00 / 1.20 / 1.40 / 1.60 / 1.80 / 2.00,and 10 pushers in steel-delrin
(mm) 0.25 / 0.40 / 0.60 / 0.80 / 1.00 / 1.20 / 1.40 / 1.60 / 1.80 / 2.00

Jewellling, Setting, staking tools - Pump pushers and anvils

Ref. AS 1000-03 Pump pusher, 3.00 mm N60 - N300
CHF 15.90
Pump pusher only, 3.00 mm

A mm, B mm: N60 A 0.40, B 0.55, N70 A 0.40, B 0.65, N80 A 0.40, B 0.75, N90
A 0.50, B 0.85, N100 A 0.50, B 0.95, N110 A 0.50, B 1.05, N120 A 0.50, B 1.15,
N130 A 0.70, B 1.25, N140 A 0.70, B 1.35, N150 A 0.70, B 1.45, N160 A 0.70, B
1.55, N170 A 0.70, B 1.65, N180 A 0.70, B 1.75, N190 A 0.80, B 1.85, N200 A 0.80,
B 1.95, N210 A 0.80, B 2.05, N220 A 0.80, B 2.15, N230 A 0.80, B 2.25, N240 A
0.80, B 2.35, N250 A 0.80, B 2.45, N260 A 0.80, B 2.55, N270 A 0.80, B 2.65, N280
A 0.80, B 2.75, N290 A 0.80, B 2.85, N300 A 0.80, B 2.95
CHF 15.90
Pump pusher only, 4.00 mm

A 0.50, B 0.85, N100 A 0.50, B 0.95, N110 A 0.50, B 1.05, N120 A 0.50, B 1.15,
N130 A 0.70, B 1.25, N140 A 0.70, B 1.35, N150 A 0.70, B 1.45, N160 A 0.70, B
1.55, N170 A 0.70, B 1.65, N180 A 0.70, B 1.75, N190 A 0.80, B 1.85, N200 A 0.80,
B 1.95, N210 A 0.80, B 2.05, N220 A 0.80, B 2.15, N230 A 0.80, B 2.25, N240 A
0.80, B 2.35, N250 A 0.80, B 2.45, N260 A 0.80, B 2.55, N270 A 0.80, B 2.65, N280
A 0.80, B 2.75, N290 A 0.80, B 2.85, N300 A 0.80, B 2.95
Ref. AS 1020-03 Pump pusher full, 3.00 mm
CHF 12.50
Full pump pusher, 3.00 mm, on request
Ref. AS 1020-04 Pump pusher full, 4.00 mm
CHF 12.50
Full pump pusher, 4.00 mm, on request
Ref. AS 1040-03 Pusher, 3.00 mm
CHF 35.00
Special pusher without spring, 3.00 mm

Ref. AS 1040-04 Pusher, 4.00 mm
CHF 35.00
Special pusher without spring, 4.00 mm
CHF 41.30
Special pump pusher, 3.00 mm

A mm, B mm: N40 A 0.20, B 0.40, N50 A 0.20, B 0.50
CHF 41.30
Special pump pusher, 4.00 mm

A mm, B mm: N40 A 0.20, B 0.40, N50 A 0.20, B 0.50
Ref. AS 1100 Anvil N60 - N317
CHF 12.30
Anvil only
A 1.00, B 1.80, N100 A 1.10, B 1.90, N110 A 1.20, B 2.00, N120 A 1.30, B 2.10,
N130 A 1.40, B 2.20, N140 A 1.50, B 2.40, N150 A 1.60, B 2.50, N160 A 1.70, B
2.70, N170 A 1.80, B 2.90, N180 A 1.90, B 3.00, N190 A 2.00, B 3.20, N200 A 2.10,
B 3.30, N210 A 2.20, B 3.40, N220 A 2.30, B 3.50, N230 A 2.40, B 3.60, N240 A
2.50, B 3.80, N250 A 2.60, B 4.00, N260 A 2.70, B 4.10, N270 A 2.80, B 4.20, N280
A 2.90, B 4.30, N290 A 3.00, B 4.40, N300 A 3.10, B 4.50, N315 A 1.00, B 1.50,
N316 A 1.30, B 2.00, N317 A 2.00, B 3.00
Ref. AS 1110 Flat anvil
CHF 12.30
Flat anvil without hole, on request

Ref. AS 1120 Special anvil
CHF 38.00
Special anvil, on request
Ref. AS 1400-01 Anvil
CHF 14.00
Fork staff anvil only
Ref. AS 1400-02-03 Pump pusher, 3.00 mm
CHF 20.00
Fork staff pusher only, 3.00 mm
CHF 20.00
Fork staff pusher only, 4.00 mm
Ref. AS 1400-03 Set of 1 anvil and 1 fork staff pusher 3.00

mm
CHF 34.00
Set of 1 anvil and 1 fork staff pusher 3.00 mm
Ref. AS 1400-04 Pump pusher and anvil 4.00 mm
CHF 34.00
Set of 1 anvil and 1 fork staff pusher 4.00 mm

Ref. AS 1410-01 Anvil
CHF 20.00
Guard pin anvil
CHF 26.00
Guard pin pusher, 3.00 mm
CHF 26.00
Guard pin pusher, 4.00 mm
CHF 46.00
Set of 1 anvil and 1 guard pin pusher 3.00 mm

CHF 46.00
Set of 1 anvil and 1 guard pin pusher 4.00 mm

Jewellling, Setting, staking tools - Pushers and anvils for Incabloc

Ref. AS 05-02-01 Anvil only for Incabloc N1 - N7
CHF 10.50
Anvil only for Incabloc, choose .

mm: N1 1.35, N2 1.60, N3 1.90, N4 2.10, N5 2.50, N6 3.00, N7 3.50
Ref. AS 05-03-01 Pusher for Incabloc 3.00 mm N1 - N6
CHF 10.00
Pusher 3mm
mm: N1 1.57, N2 1.87, N3 2.07, N4 2.47, N5 2.97, N6 3.47
Ref. AS 05-04-01 Pusher only for Incabloc 4 mm N1 - N6
CHF 10.00
Pusher only for Incabloc 4mm

mm: N1 1.57, N2 1.87, N3 2.07, N4 2.47, N5 2.97, N6 3.47

Pivoting lathe - Assortments

Ref. TP 106 Pivoting lathe set
CHF 2'130.00
Pivoting lathe in his casket with runners:

Ref. TP 123
Ref. TP 125
Ref. TP 127
Ref. TP 106-119 Movable pivoting lathe set
CHF 2'430.00
Movable pivoting lathe in his casket with runners:

Ref. TP 123
Ref. TP 125
Ref. TP 127
Ref. TP 108 Pivoting lathe set
CHF 2'525.00
Pivoting lathe set in his casket with runners:

Ref. TP 123
Ref. TP 124
Ref. TP 125
Ref. TP 127
Ref. TP 108-119 Movable pivoting lathe set
CHF 2'825.00
Movable pivoting lathe set in his casket with runners:

Ref. TP 123
Ref. TP 124
Ref. TP 125
Ref. TP 127

Pivoting lathe - Accessories

Ref. TP 100 Pivoting lathe
CHF 800.00
Pivoting lathe to use with vice or ref. M 300
Ref. TP 100-119 Movable pivoting lathe
CHF 1'100.00
To use with a vice or ref. TP M 300
Ref. TP 117a Runner
CHF 420.00
Pour pivots de 0.38 - 1.00 mm
Ref. TP 118 Runner
CHF 420.00
Ref. TP 118a Runner
CHF 420.00
Ref. TP 122 Cylinder
CHF 110.00
Pour rf. TP 124 / 125 / 126
Ref. TP 122a Cylinder
CHF 110.00
Pour rf. TP 117a / 118 / 118a
Ref. TP 123 Runner
CHF 230.00
With pivot-bed disc for pivots from 0.15 to 0.30 mm

Ref. TP 124 Runner
CHF 395.00
Pour pivots de 0.04 0.10 mm
Ref. TP 125 Runner
CHF 395.00
Ref. TP 126 Runner
CHF 395.00
Ref. TP 127 Runner
CHF 395.00
Pour pivots de 0.16 0.36
Ref. TP 129 Lantern N1 - N4
CHF 65.00
Lantern alone
mm: N1 0.04 - 0.10, N2 0.10 - 0.15, N3 0.04 - 0.15, N4 0.16 - 0.36
Ref. TP 134 Spool
CHF 130.00
Ref. TP 134a Spool spring
CHF 10.00
Pour rf. TP 134
Ref. TP 135 Pulley
CHF 55.00

Ref. TP 135a Fork
CHF 18.00
Pour rf. TP 135
Ref. TP 155a Bow
CHF 68.00
Pour travail main

Apparatus M and MTM - Assortment

Ref. M 300 Apparatus M
CHF 1'800.00
To use with pivoting lathe ref. TP 100

Improved apparatus for rolling, polishing and rounding of pivots of 0.04 to 1.20 mm.
The apparatus is designed to watch-repairers, finishers and to retouch ing and pivoting workshops,
possibly also for small series.
Grindstone in hardmetal
Ref. M 301 Apparatus M
CHF 1'980.00
To use with pivoting lathe ref. TP 100

In his box
Ref. MTM 310-06 Apparatus MTM
CHF 3'400.00
With runners ref. TP 123 / 126 / 127
In his box
Ref. MTM 310-08 Apparatus MTM
CHF 3'795.00
With runners ref. TP 123 / 124 / 125 / 127
In his box

Apparatus M and MTM - Accessories

Ref. M 302 Grindstone
CHF 465.00
Meule fine D30
CHF 425.00
Meule normale D60
CHF 425.00
Meule grossire D150
Ref. M 310 Grindstone renew
CHF 235.00
To make that the grindstone cut again

Polishing screws - Lathe

Ref. TV 100 Polishing screws lathe in his box
CHF 1'900.00
1 storage casket
1 lathe with chuck and spindle 8 mm 5 mm
3 grindstones 50 mm: 1 in cast-iron, 1 in bronze, 1 in boxwood
1 set of 22 chucks 5 mm from 0.40 to 2.50 mm
1 set of 12 lantern 5 mm from 0.40 to 2.50 mm

Polishing screws - Tripod

Ref. TR 10 Apparatus Tripod to polish screws
CHF 580.00
Apparatus Tripod to polish the head of the screws

With paper 5 micron
With diamantine pasta
With pewter plate
Ref. TR 10-01 Tripod
CHF 330.00
Only the Tripod

Polishing screws - Accessories

Ref. TR 10-02 Diamantin Pasta
CHF 73.00
Tube of diamantin pasta for polishing screws

"Taille": 1 micron, 3 micron
Ref. TR 10-03 Papier autocollant
CHF 8.00
Choisir le grain ou sur demande.

Grain: 3 microns, 5 microns
Ref. TV 101 Polishing screws lathe
CHF 500.00
Tour polir les vis seul
Ref. TV 102 Grindstone
CHF 90.00
Boxwood stack
CHF 90.00
Meule en bronze de 50 mm

CHF 90.00
Meule en fonte de 50 mm
CHF 130.00
Meule en tain de 50 mm
Ref. TV 106 Set of 22 brass chucks
CHF 692.30
Jeu de pinces laiton corps 5.00 mm de 0.40 2.50 mm par 0.10 mm
Ref. TV 106-01 Brass chuck N1 - N7 (0.40 - 1.00 mm)
CHF 37.20
Brass chuck alone

mm: N1 0.40, N2 0.50, N3 0.60, N4 0.70, N5 0.80, N6 0.90, N7 1.00
Ref. TV 106-02 Brass chuck N1 - N15 (1.10 - 2.50 mm)
CHF 28.90
Brass chuck alone

mm: N1 1.10, N2 1.20, N3 1.30, N4 1.40, N5 1.50, N6 1.60, N7 1.70, N8
1.80, N9 1.90, N10 2.00, N11 2.10, N12 2.20, N13 2.30, N14 2.40, N15 2.50

Ref. TV 107 Set of 12 brass lantern
CHF 395.60
Jeu de 12 lanternes corps 5.00 mm de 0.30 2.50 mm

0.30 / 0.40 / 0.50 / 0.60 / 0.80 / 1.00 /
1.20 / 1.50 / 1.70 / 2.00 / 2.20 / 2.50
Ref. TV 107-01 Brass lantern N1 - N6 (0.30 - 1.00 mm)
CHF 37.20
Brass lantern alone

mm: N1 0.30, N2 0.40, N3 0.50, N4 0.60, N5 0.80, N6 1.00
Ref. TV 107-02 Brass lantern N1 - N6 (1.20 - 2.50 mm)
CHF 28.90
Brass lantern alone

mm: N1 1.20, N2 1.50, N3 1.70, N4 2.00, N5 2.20, N6 2.50

Apparatus multi-fonction - Assortment

Ref. AMF 2000 Apparatus multifunctions alone
CHF 353.00
Rf AMF 2000
Machine simple
Ref. AMF 2000-b Apparatus multi-fonction
CHF 473.90
1 apparatus multi-fonction
1 armband support
2 points to push out
1 point to push
1 spanner 6 sides

Ref. AMF 2000-c Complete set
CHF 1'030.10
Wood box with:

1 apparatus multi-fonction
1 support for armband
1 support to open the backs, with V support
1 support to open the backs, with radius support
1 support to push the tubes
1 support to push the tubes out
2 arbors steel-delrin to push the correctors
2 arbors steel-delrin to push the pushers
1 knife to open the backs
1 short point to push the pins out
1 long point to push the pins out
1 point to push the pins
1 set of arbors to push the tubes
1 set of arbors to push the correctors and pushers out
1 set of arbors to push the tubes out
2 arbors steel-brass to push the tubes out
2 keys
1 screwdriver

Apparatus multi-fonction - Support and accessories

Ref. AMF 2000-01 Storing box
CHF 61.90
Box with storing foam and arbor support
Ref. AMF 2000-09-01 Support in steel
CHF 34.00
Support in steel for arbor to pull out
Ref. AMF 2000-09-02 Support in steel
CHF 34.00
Support in steel for arbor to pull in
Ref. AMF 2000-21 Support for armband
CHF 31.00
Support for armband in synthetic material
Ref. AMF 2000-22 Support
CHF 31.00
Delrin support to open the backs with V support

Ref. AMF 2000-23 Suppor
CHF 31.00
Delrin support to open the backs with comb support
Ref. AMF 2000-24 Holder for big boxes
CHF 100.00
Holder for big boxes with screwPleaze ask for the price, below is only for indication

Apparatus multi-fonction - Arbors

Ref. AMF 2000-03 Set of arbors
CHF 66.40
Set of arbors to push the box iron-delrin
Ref. AMF 2000-03-01 Arbor
CHF 16.60
Arbor to push the box iron-delrin
CHF 16.60
Arbor to push the correctors iron-delrin
CHF 16.60
Iron-delrin
CHF 16.60
Arbor to push the pushers iron-delrin

Ref. AMF 2000-03-05 Steel and brass arbor
CHF 16.60
Steel and brass arbor
CHF 111.30
Set of 9 arbors to push the tubes

0.95 / 1.05 / 1.15 / 1.25 / 1.35 / 1.45 / 1.55 / 1.65 / 1.95 mm
Ref. AMF 2000-04-01 Arbor N1 - N9
CHF 12.50
Arbor to push the tubes

mm: N1 0.95, N2 1.05, N3 1.15, N4 1.25, N5 1.35, N6 1.45, N7 1.55, N8
1.65, N9 1.95
CHF 43.40
Set of 6 arbors to push correctors and pushers out

A (+/- 0.02), B (+/- 0.02): 1.05 mm, 1.65 mm / 1.15 mm, 1.75 mm / 1.35 mm, 1.95 mm / 1.45 mm,
2.05 mm / 1.55 mm, 2.15 mm / 1.85 mm, 2.45 mm
Ref. AMF 2000-06-01 Arbor N1 - N6
CHF 7.30
Arbor to push out the pushers and correctors

int. (+/- 0.02) mm, ext. (+/- 0.02) mm: N1 1.05, 1.65, N2 1.15, 1.75, N3 1.35,
1.95, N4 1.45, 2.05, N5 1.55, 2.15, N6 1.85, 2.45

CHF 79.40
Set of 11 arbors to push the tubes out

A (+/- 0.02), B (+/- 0.02): 0.92 mm, 1.15 mm / 0.92 mm, 1.45 mm / 0.92 mm, 1.75 mm / 1.02 mm,
1.25 mm / 1.12 mm, 1.35 mm / 1.22 mm, 1.45 mm / 1.22 mm, 1.75 mm / 1.32 mm, 1.55 mm / 1.32 mm,
1.75 mm / 1.42 mm, 1.75 mm / 1.52 mm, 1.95 mm
Ref. AMF 2000-07-01 Arbor N1 - N11
CHF 7.30
Arbor to push out the tubes

int. (+/- 0.02) mm, ext. (+/- 0.02) mm: N1 0.92, 1.15, N2 0.92, 1.45, N3 0.92,
1.75, N4 1.02, 1.25, N5 1.12, 1.35, N6 1.22, 1.45, N7 1.22, 1.75, N8 1.32,
1.55, N9 1.32, 1.75, N10 1.42, 1.75, N11 1.52, 1.95
Ref. AMF 2000-30 Set of 3 points
CHF 27.90
To push and push out

0.90 mm
Ref. AMF 2000-31 Long point
CHF 9.40
To push out the metal pin

0.90 mm
Ref. AMF 2000-32 Short point
CHF 9.40
To push out the metal pin

0.90 mm

Ref. AMF 2000-33 Point
CHF 9.40
To push the metal pin

Apparatus multi-fonction - Knives

Ref. AMF 2000-05 Standard knife
CHF 31.00
Standard knife, angle 20
Ref. AMF 2000-05-00 Set of knives
CHF 310.00
1x excentric 25, 6 mm large

1x 15
1x 25
1x 35
1x 45
1x excentric 25, 4 mm thin
1x flat 15
1x small 20
1x small 15
1x two angles 25 55
Ref. AMF 2000-05-01 Knife to open cover
CHF 31.00
Excentric knife to open cover. Angle 25, 6.00 mm large
CHF 31.00
Knife to open cover. Angle 15
CHF 31.00
Knife to open cover Angle 25

CHF 31.00
CHF 31.00
CHF 31.00
Excentric knife with angle 25, 4.00 mm large
CHF 31.00
Flat knife, angle 15
CHF 31.00
Tight knife, angle 20
CHF 31.00
Tight knife, angle 15

CHF 31.00
Knife with 2 slopes, angle 25 and 55

Knurling tools - Knurling tools

Ref. AM 101 Knurling tool
CHF 440.00
Modle main, avec jeu de molettes standard 45 dents pour moletage crois, capacit 2.5 25 mm
Ref. AM 202 Knurling tool
CHF 515.00
Modle main, avec jeu de molettes standard 45 dents pour moletage crois, capacit 3 40 mm
Ref. ROTO 01 Apparatus Rotoflex
CHF 650.00
Capacity:
8 x 8 and 7 x 7
(10 x 4 x 3)

Knurling tools - Grindwheel

Ref. AM 101-01 Grindwheel 10x4x3 form A
CHF 72.00
Grindwheel, size 10 x 4 x 3 mm
Form A for right knurling
Nombre de dents / pas du moletage: 20 / 1.55 mm, 25 / 1.25 mm, 27 / 1.15 mm, 30 / 1.10 mm, 32 /
0.90 mm, 35 / 0.80 mm, 40 / 0.70 mm, 45 / 0.62 mm, 50 / 0.62 mm, 55 / 0.57 mm, 60 / 0.50 mm
Ref. AM 101-02 Grindwheel 10x4x3 form BL
CHF 24.00
Form BL for crossed knurling
0.75 mm, 40 / 0.65 mm, 45 / 0.60 mm, 50 / 0.55 mm, 55 / 0.50 mm, 60 / 0.45 mm, 70 / 0.40 mm
Ref. AM 101-03 Grindwheel 10x4x3 form BR
CHF 24.00
Form BR for crossed knurling
0.75 mm, 40 / 0.65 mm, 45 / 0.60 mm, 50 / 0.55 mm, 55 / 0.50 mm, 60 / 0.45 mm, 70 / 0.40 mm
Ref. AM 101-04 Set of grindwheel 10x4x3 form BL/BR
CHF 72.00
Set of 3 grindwheel, size 10 x 4 x 3 mm

Form BL / BR
0.75 mm, 40 / 0.65 mm, 45 / 0.60 mm, 50 / 0.55 mm, 55 / 0.50 mm, 60 / 0.45 mm, 70 / 0.40 mm
Ref. AM 101-05 Set of grindwheel 10x4x3 form A
CHF 72.00

Form A

Ref. AM 202-01 Grindwheel 15x5x4 form A
CHF 24.00
Form A for right knurling
1.35 mm, 40 / 1.20 mm, 45 / 1.05 mm, 50 / 0.95 mm, 55 / 0.90 mm, 60 / 0.80 mm, 70 / 0.67 mm, 80 /
0.60 mm, 90 / 0.50 mm
Ref. AM 202-02 Grindwheel 15 x 5 x 4 form BL
CHF 24.00
Form BL for crossed knurling
1.00 mm, 45 / 0.90 mm, 50 / 0.80 mm, 55 / 0.75 mm, 60 / 0.70 mm, 70 / 0.60 mm, 80 / 0.50 mm
Ref. AM 202-03 Grindwheel 15 x 5 x 4 form BR
CHF 24.00
Form BR for crossed knurling
1.00 mm, 45 / 0.90 mm, 50 / 0.80 mm, 55 / 0.75 mm, 60 / 0.70 mm, 70 / 0.60 mm, 80 / 0.50 mm
Ref. AM 202-04 Set of grindwheel 15x5x4 form A
CHF 72.00

Form A
1.00 mm, 45 / 0.90 mm, 50 / 0.80 mm, 55 / 0.75 mm, 60 / 0.70 mm, 70 / 0.60 mm, 80 / 0.50 mm
Ref. AM 202-05 Set of grindwheel 15x5x4 form BL/BR
CHF 72.00

Form BL / BR
1.35 mm, 40 / 1.20 mm, 45 / 1.05 mm, 50 / 0.95 mm, 55 / 0.90 mm, 60 / 0.80 mm, 70 / 0.67 mm, 80 /
0.60 mm, 90 / 0.50 mm

Pieces holders - Pieces holders

Ref. PP 400-410-420 Znith et Rolex 4030
CHF 320.00
Movement holder Znith 400-410-420 Rolex 4030
Ref. PP 57 Movement holder
CHF 30.00
Movement holder to put the hands

With adjustable support screw
For setting tool base 31 mm
Ref. PP 58 Movement holder
CHF 30.00
Movement holder to put the hands

With adjustable support screw
For setting tool base 31 mm
Ref. PP 7750-51-53 Piece holder to set hands
CHF 140.00
Cal. 7750-51-53
Ref. PP 7750-53 Piece holder cal. 7750-53
CHF 315.00
Piece holder for caliber 7750-53

Baskets - Baskets
Ref. PA 400-00 Set of 5 baskets 63mm
CHF 580.00
Set of 5 baskets of washing 63 mm

6 seeparations, 4 seeparations, 3 seeparations, 2 seeparations, without seeparations
1 cover et 5 kernel of positioning for baskets
Ref. PA 400-01 Basket 63mm
CHF 85.00
Baskets of washing 63 mm without seeparations
CHF 90.00
Baskets of washing 63 mm with 2 seeparations
CHF 100.00
CHF 110.00
CHF 170.00

Ref. PA 400-10 Cover 63mm
CHF 24.00
Cuver for basket Ref PA 400-01
Ref. PA 400-12 Segment
CHF 5.80
Segment of separation for baskets
Ref. PA 400-13 Kernel
CHF 3.20
Kernel of positioning for baskets
Ref. PA 450-01 Complete basket 82mm
CHF 175.20
Complete basket
16 compartments
2 big segments
8 little segments
1 core
1 cover
ext. 82 mm, height 8 mm
CHF 85.60
Basket only
Without core
Without separation

CHF 88.70
Basket only
With core
Without separation
CHF 105.70
Basket with 3 compartments

With core and 3 little segments
CHF 131.40

With core, cover and 3 little segments
CHF 111.30


CHF 137.10

CHF 134.00

CHF 159.70

mm: N1 0.90, N2 3.00
Ref. PA 460-01 Wash-basket
CHF 11.80
23 mm
CHF 11.80
16 mm

CHF 11.80
14 mm

Baskets - Accessories
Ref. PA 450-10 Cover
CHF 25.80
Couvercle seul
Ref. PA 450-11 Big segment
CHF 8.30
Grand segment seul
Ref. PA 450-12 Little segment
CHF 5.80
Petit segment seul
Ref. PA 450-13 Core
CHF 3.20
Noyau seul

Tools - Tools
Ref. BL 01 Filling tool
CHF 1'260.00
Capacity: 40 x 25 mm
Max. height: 10 mm
Ref. CG 100 Compass for engraver
CHF 235.00
Compass for engraver
Ref. ET 01 Vice
CHF 298.00
Precision vice
Size 15 x 15 mm
Max. opening 12 mm
Ref. ET 02 Small plates
CHF 49.50
Small remplacement plates
Ref. ET 03 Hands vice
CHF 235.00
Hands vice for "aiguilles"

Ref. HC 01 Truing caliper
CHF 385.00
Truing caliper on his base
Ref. MA 01 Handchuck
CHF 74.00
Handchuck for chuck B8
Ref. SP 01 Support
CHF 43.00
Support for chucks B8

Without chuck
Ref. TOH 100 Support for Tohnichi
CHF 580.00
Support for Tohnichi

Tools - Screwdrivers
Ref. TO 02 Set of screwdrivers
CHF 82.50
8 pieces 0.60 / 0.80 / 1.00 / 1.20 / 1.40 / 1.60 / 2.00 / 2.50 mm

1 base without little tubes for "mches"
Ref. TO 02-02 Screwdriver N1 - N5 (0.60 - 1.40 mm)
CHF 4.10
Inox screwdriver only

Price per piece, for minimum 100 pieces
Body 4.00 mm
mm: N1 0.60, N2 0.80, N3 1.00, N4 1.20, N5 1.40
CHF 4.30

Price per piece, for minimum 100 piece
Body 0.50 to 1.50, 4.00 mm
Body 1.60 to 2.00, 4.50 mm
mm: N1 0.50, N2 0.70, N3 0.90, N4 1.10, N5 1.30, N6 1.50, N7 1.60, N8
1.80, N9 2.00
CHF 4.80

Price per piece, for minimum 50 pieces
Body 5.00 mm
mm: N1 2.20, N2 2.50, N3 3.00
Ref. TO 02-05 Screwdriver (3.50 mm)
CHF 5.80
Price per piece for a minimum of 10 pieces

Inox screwdriver 3.50 mm
Body 5.00 mm
Ref. TO 02-06 Screwdriver's gimlet N1 - N7 (0.60 - 1.20 mm)
CHF 37.00
Screwdriver's gimlet
Price for 100 pieces
mm: N1 0.60, N2 0.70, N3 0.80, N4 0.90, N5 1.00, N6 1.10, N7 1.20

CHF 40.00
: N1 1.30, N2 1.40, N3 1.50, N4 1.60, N5 1.70, N6 1.80, N7 1.90, N8 2.00
CHF 55.00
mm: N1 2.50, N2 2.60, N3 2.70, N4 2.80, N5 2.90, N6 3.00

Tools - Set of Keys for tubes and pushers

Ref. CL 10 Keys and screwdriver in box
CHF 1'033.00
Box with screwdriver's handle and 17 keys for tubes, pushers or correctors.
Ref. TO 10 01: screwdriver's handle
Ref. TO 10 10 01: hex key 1.40 for tube
Ref. TO 10 10 02: hex key for tube
Ref. TO 10 10 04: key 8 sides 1.78 for tube
Ref. TO 10 10 06: key 8 sides 2.18 for tube
Ref. TO 10 20 01: key int. for pusher 8 sides 2.47
Ref. TO 10 20 04: int. hex key 3.35
Ref. TO 10 30 01: key int. 22 teeth
Ref. TO 10 30 02: key int. 16 teeth for screwed corrector Boninchi
Ref. TO 10 30 03: key int. 22 teeth
Ref. TO 10 40 01: key 16 teeth for tubes
Ref. CL 10-01 Screwdriver's handle
CHF 23.00
Only Screwdriver's handle for keys
Ref. CL 10-C01 Empty box
CHF 60.00
Empty box with cutted foam

Tools - Keys
Ref. CL 10-10-01 Hex key 1.40 ext.
CHF 52.00
Hex key 1.40 mm extern for tube
Ref. CL 10-10-02 Hex key ext.
CHF 52.00
Hex key 1.52 mm extern for tubes
CHF 52.00
Ref. CL 10-10-04 Key 8 sides 1.78 ext.
CHF 52.00
Key 8 sides 1.78 mm extern for tubes
CHF 52.00
Ref. CL 10-10-06 Key 8 sides 2.18 ext.
CHF 52.00
Key 8 sides 2.18 mm extern for tubes

Ref. CL 10-20-01 Key 8 sides 2.47 int.
CHF 58.00
Key 8 sides 2.47 mm intern for pushers
CHF 58.00
CHF 58.00
Ref. CL 10-20-04 Hex key 3.35 int.
CHF 58.00
Hex key 3.35 mm intern
Ref. CL 10-30-01 Key 22 teeth int.
CHF 58.00
Key 22 teeth intern

internal set of teeth: 2.51 mm
external set of teeth: 2.80 mm
CHF 58.00
Key 16 teeth intern for screwed corrector Boninchi


CHF 58.00
Key 22 teeth intern

Ref. CL 10-40-01 Key 16 teeth ext.
CHF 58.00
Key 16 teeth extern for tubes

CHF 58.00

CHF 58.00

CHF 58.00


Tools - Tool to set armwrist

Ref. BLMD 100 Tool to set armwrist
CHF 130.00
Tool to set armwrist with one base and two screwdrivers. To have a good stand by setting armwrist on
the case. The screwdrivers are guided in two tubes. This device ensure a good stand and precise way
for screw and unscrew armwrist to/from case. The movable supports can be ordered according to the
case and armwrist. The fuses of the screwdrivers are interchangeable.
Ref. TO 10-01 Screwdriver's handle
CHF 23.00
Only screwdriver's handle for BLMD 100
Ref. TO 10-01 N Screwdriver's pin
CHF 5.50

Motors - Motors
Ref. MO 2200 Motor
CHF 1'750.00
Motor to finish pieces

With 1 chuck with 3 aluminium jaws and 3 plastic jaws

Micros - Micros
Ref. MI 100-01 Micros in wood N1 - N3
CHF 48.00
Micros in wood, different kind of wood

Enlargment 2x, 3x, 4x, 5x, 6x, 10x
Bois/Holz/Wood: N1 Poirier/Birnbaum/Pear-tree, N2 Cerisier/Kirschbaum/Cherry-tree, N3
Buis/Buchsbaum/Boxwood
CHF 56.00

Bois/Holz/Wood: N1 If/Eibe/Yew, N2 Noyer/Walnussbaum/Walnut-tree, N3
Olivier/Olivenbaum/Olive-tree
CHF 76.00

Bois/Holz/Wood: N1 Erable mouchet/Ahorn/Maple, N2 Ebne de Macasar/Ebenholz
Macasar/Ebony Macasar, N3 Ebne du Gabon/Ebenholz Gabon/Ebony Gabon, N4 Bois de
rose/Rosenholz/Rosewood, N5 Bois de violette, N6 Bois d'amourette
Ref. MI 101 Ring
CHF 5.00
Brass ring
Ref. MI 102 Laser engraving
CHF 5.00
Laser engraving of the logo

For ref. MI 100-1 / 100-2 / 100-3
Price for one piece for a minimum of 50 pieces

Ref. MI 200 Micros in aluminium
CHF 34.00
25 colors
Ref. MI 201 Laser engraving
CHF 4.00
Laser engraving of the logo

Price for one piece for a minimum of 50 pieces
Ref. MI 202 Micros in plastic
CHF 22.00
Micros unbreakable in plastic

With ring in aluminium


Horia

Uploaded by

Copyright:

Available Formats

Horia

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Horia

Uploaded by

Copyright:

Available Formats

What equipment is included in the basic watchmaker's lathe assortment?

What equipment is included in the basic watchmaker's lathe assortment?

What additional equipment can be added to the lathe?

What additional equipment can be added to the lathe?

Price list 2013

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Watchmaker's Lathe - Assortment

Ref. TH 40a Drawer 1

Ref. TH 40b Drawer 2

60 chucks B 8 mm from 0.40 to 7.00 mm ref. TH 15D

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Ref. TH 40c Drawer 3

Ref. TH 40d Drawer 4

Ref. TH 50 Watchmaker's Lathe, assortment

Lathe bed 220 mm, ref. TH 4a

Ref. TH 51 Watchmaker's lathe, assortment

Lathe bed 220 mm, ref. TH 4a

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Ref. TH 60 Watchmaker's lathe, assortment

Lathe bed ref. TH 4

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Watchmaker's Lathe - Accessories

With fastening screws and bolt

Ref. TH 01a Lathe foot

Adjustable lathe foot

Ref. TH 02 Lathe foot

With screws and bolt

Ref. TH 03 Hand flywheel

For fitting to vice

Ref. TH 03b Belt tightening device

For lathe foot ref. TH 3b

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Ref. TH 04 Lathe bed

Ref. TH 04a Lathe bed

Ref. TH 05-02 Brace for chuck B8

Brace for tailstock TH 05 for chuck B8

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Ref. TH 08b Spindle

Spindle for Ref. TH 6 and TH 7

Ref. TH 08c Brace

Brace for Ref. TH 8a

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Watchmaker's Lathe - Slide rest and turning tools

To use with Ref. 13

Ref. TH 10 Tip-over T rest

Ref. TH 10a T rest

Ref. TH 10b Roller T rest

Ref. TH 10c Small T rest

Small T rest for ref. TH 10

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Ref. TH 13 Slide rest

Ref. TH 14 Tool post

Very light tool post, movable in all directions

Ref. TH 14a Tool holder

Extra-strong tool holder. Recommended for special work.

Ref. TH 14b Turret

Ref. TH 14c Graver

Horia SA - Rue de l'Avenir 23 - 2852 Courtetelle - Switzerland

Ref. TH 39 Graver kit