Network Topologies: What Is A Network Topology?

Network Topologies:
What is a Network topology?
A network topology is the geometric arrangement of nodes and cable links in a

LAN,
There are three topology’s to think about when you get into networks. These are
the star, rind, and the bus.
Star, a ring topology features a logically closed loop. Data packets travel in a
single direction around the ring from one network device to the next. Each
network device acts as a repeater, meaning it regenerates the signal
Ring, in a star topology each node has a dedicated set of wires connecting it to a
central network hub. Since all traffic passes through the hub, the hub becomes a
central point for isolating network problems and gathering network statistics.
Bus, the bus topology, each node (computer, server, peripheral etc.) attaches
directly to a common cable. This topology most often serves as the backbone for
a network. In some instances, such as in classrooms or labs, a bus will connect
small workgroups
Collisions:
Ethernet is a shared media, so there are rules for sending packets of data to
avoid conflicts and protect data integrity. Nodes determine when the network is
available for sending packets. It is possible that two nodes at different locations
attempt to send data at the same time. When both PCs are transferring a packet
to the network at the same time, a collision will result.
Minimizing collisions is a crucial element in the design and operation of networks.

Increased collisions are often the result of too many users on the network, which
results in a lot of contention for network bandwidth. This can slow the
performance of the network from the user's point of view. Segmenting the
network, where a network is divided into different pieces joined together logically
with a bridge or switch, is one way of reducing an overcrowded network.
Ethernet Products:
The standards and technology that have just been discussed help define the
specific products that network managers use to build Ethernet networks. The
following text discusses the key products needed to build an Ethernet LAN.
Transceivers
Transceivers are used to connect nodes to the various Ethernet media. Most
computers and network interface cards contain a built-in 10BASE-T or 10BASE2
transceiver, allowing them to be connected directly to Ethernet without requiring
an external transceiver. Many Ethernet devices provide an AUI connector to
allow the user to connect to any media type via an external transceiver. The AUI
connector consists of a 15-pin D-shell type connector, female on the computer
side, male on the transceiver side. Thickwire (10BASE5) cables also use
transceivers to allow connections.
For Fast Ethernet networks, a new interface called the MII (Media Independent
Interface) was developed to offer a flexible way to support 100 Mbps
connections. The MII is a popular way to connect 100BASE-FX links to copper-
based Fast Ethernet devices.
Network Interface Cards:
Network interface cards, commonly referred to as NICs, and are used to connect
a PC to a network. The NIC provides a physical connection between the
networking cable and the computer's internal bus. Different computers have
different bus architectures; PCI bus master slots are most commonly found on
486/Pentium PCs and ISA expansion slots are commonly found on 386 and older
PCs. NICs come in three basic varieties: 8-bit, 16-bit, and 32-bit. The larger the
number of bits that can be transferred to the NIC, the faster the NIC can transfer
data to the network cable.
Many NIC adapters comply with Plug-n-Play specifications. On these systems,

NICs are automatically configured without user intervention, while on non-Plug-n-
Play systems, configuration is done manually through a setup program and/or
DIP switches.
Cards are available to support almost all networking standards, including the
latest Fast Ethernet environment. Fast Ethernet NICs are often 10/100 capable,
and will automatically set to the appropriate speed. Full duplex networking is
another option, where a dedicated connection to a switch allows a NIC to operate
at twice the speed.
Hubs/Repeaters:
Hubs/repeaters are used to connect together two or more Ethernet segments of

any media type. In larger designs, signal quality begins to deteriorate as
segments exceed their maximum length. Hubs provide the signal amplification
required to allow a segment to be extended a greater distance. A hub takes any
incoming signal and repeats it out all ports.
Ethernet hubs are necessary in star topologies such as 10BASE-T. A multi-port
twisted pair hub allows several point-to-point segments to be joined into one
network. One end of the point-to-point link is attached to the hub and the other is
attached to the computer. If the hub is attached to a backbone, then all
computers at the end of the twisted pair segments can communicate with all the
hosts on the backbone. The number and type of hubs in any one-collision
domain is limited by the Ethernet rules. These repeater rules are discussed in
more detail later.
Max Nodes Max Distance

Network Type
Per Segment Per Segment
10BASE-T 2 100m
10BASE2 30 185m
10BASE5 100 500m
10BASE-FL 2 2000m
Adding Speed:
While repeaters allow LANs to extend beyond normal distance limitations, they
still limit the number of nodes that can be supported. Bridges and switches,
however, allow LANs to grow significantly larger by virtue of their ability to
support full Ethernet segments on each port. Additionally, bridges and switches
selectively filter network traffic to only those packets needed on each segment -
this significantly increases throughput on each segment and on the overall
network. By providing better performance and more flexibility for network
topologies, bridges and switches will continue to gain popularity among network
managers.
Bridges:
The function of a bridge is to connect separate networks together. Bridges

connect different networks types (such as Ethernet and Fast Ethernet) or
networks of the same type. Bridges map the Ethernet addresses of the nodes
residing on each network segment and allow only necessary traffic to pass
through the bridge. When a packet is received by the bridge, the bridge
determines the destination and source segments. If the segments are the same,
the packet is dropped ("filtered"); if the segments are different, then the packet is
"forwarded" to the correct segment. Additionally, bridges do not forward bad or
misaligned packets.
Bridges are also called "store-and-forward" devices because they look at the
whole Ethernet packet before making filtering or forwarding decisions. Filtering
packets, and regenerating forwarded packets enable bridging technology to split
a network into separate collision domains. This allows for greater distances and
more repeaters to be used in the total network design.
Ethernet Switches:
Ethernet switches are an expansion of the concept in Ethernet bridging. LAN

switches can link four, six, ten or more networks together, and have two basic
architectures: cut-through and store-and-forward. In the past, cut-through
switches were faster because they examined the packet destination address only
before forwarding it on to its destination segment. A store-and-forward switch, on
the other hand, accepts and analyzes the entire packet before forwarding it to its
destination.
It takes more time to examine the entire packet, but it allows the switch to catch
certain packet errors and keep them from propagating through the network. Both
cut-through and store-and-forward switches separate a network into collision
domains, allowing network design rules to be extended. Each of the segments
attached to an Ethernet switch has a full 10 Mbps of bandwidth shared by fewer
users, which results in better performance (as opposed to hubs that only allow
bandwidth sharing from a single Ethernet). Newer switches today offer high-
speed links, FDDI, Fast Ethernet or ATM. These are used to link switches
together or give added bandwidth to high-traffic servers. A network composed of
a number of switches linked together via uplinks is termed a "collapsed
backbone" network.
Routers:
Routers filter out network traffic by specific protocol rather than by packet
address. Routers also divide networks logically instead of physically. An IP router
can divide a network into various subnets so that only traffic destined for
particular IP addresses can pass between segments. Network speed often
decreases due to this type of intelligent forwarding. Such filtering takes more time
than that exercised in a switch or bridge, which only looks at the Ethernet
address. However, in more complex networks, overall efficiency is improved by
using routers.

Network Topologies: What Is A Network Topology?

Uploaded by

Copyright:

Available Formats

Network Topologies: What Is A Network Topology?

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Network Topologies: What Is A Network Topology?

Uploaded by

Copyright:

Available Formats

Network Topologies:

What is a Network topology?

A network topology is the geometric arrangement of nodes and cable links in a

Minimizing collisions is a crucial element in the design and operation of networks.

Network Interface Cards:

Many NIC adapters comply with Plug-n-Play specifications. On these systems,

Hubs/repeaters are used to connect together two or more Ethernet segments of

Max Nodes Max Distance

The function of a bridge is to connect separate networks together. Bridges

Ethernet switches are an expansion of the concept in Ethernet bridging. LAN

You might also like