One Martin Place

Neponset, IL 61345-9766 USA

800-544-2947 or 309-852-2384
FAX: 800-814-1553
www.martin-eng.com
We Make Your Bulk Materials Handling
Cleaner, Safer and More Productive
Through Personalized Performance.
Go to MARTIN

SQC2

Square Mainframe Belt Cleaner web page

Go to MARTIN

SAF-2

Belt Cleaner web page

Form No. M3820-08/11
2010, 2011 MARTIN ENGINEERING COMPANY. All rights reserved.
Operators Manual
M3820
MARTIN

SAF-2

&
MARTIN

SQC2

Square Mainframe Belt Cleaners
Important
MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO
CONTAMINATION OF THE MATERIAL; USERS FAILURE TO INSPECT, MAINTAIN AND TAKE
REASONABLE CARE OF THE EQUIPMENT; INJ URIES OR DAMAGE RESULTING FROM USE OR
APPLICATION OF THIS PRODUCT CONTRARY TO INSTRUCTIONS AND SPECIFICATIONS
CONTAINED HEREIN. MARTIN ENGINEERINGS LIABILITY SHALL BE LIMITED TO REPAIR
OR REPLACEMENT OF EQUIPMENT SHOWN TO BE DEFECTIVE.
Observe all safety rules given herein along with owner and Government standards and regulations. Know
and understand lockout/tagout procedures as defined by American National Standards Institute (ANSI)
z244.1-1982, American National Standard for Personnel Protection - Lockout/Tagout of Energy Sources -
Minimum Safety Requirements and Occupational Safety and Health Administration (OSHA) Federal
Register, Part IV, 29 CFR Part 1910, Control of Hazardous Energy Source (Lockout/Tagout); Final Rule.
The following symbols may be used in this manual:
DANGER
!
Danger: Immediate hazards that will result in severe personal injury or death.

WARNING
!
Warning: Hazards or unsafe practices that could result in personal injury.
CAUTION
!
Caution: Hazards or unsafe practices that could result in product or property damages.
IMPORTANT
Important: Instructions that must be followed to ensure proper installation/operation of equipment.
NOTE
Note: General statements to assist the reader.
Martin Engineering M3820-10/11 i MARTIN

SAF-2 and MARTIN

SQC2

Square Mainframe Belt Cleaner

Table of Contents
Section Page
List of Figures and Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installations without chutework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Belt cleaner inspection access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Urethane shelf life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Installing Belt Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing Belt Cleaner Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Marking chute cutouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Removing blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing blade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
After Installing Belt Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Weekly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
T
a
b
l
e

o
f

C
o
n
t
e
n
t
s
Martin Engineering M3820-10/11 ii MARTIN

SAF-2 and MARTIN

SQC2

Square Mainframe Belt Cleaner

List of Figures
Figure Title Page
1 Mounting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Removing and Installing Blade Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly,
P/N SQC2S-XXXXXXXXXX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly,
with 3-in. MARTIN

SAF-2 Style Blades, P/N SQC2S-XXXXXX3XXX . 14

5 MARTIN

SAF-2 Belt Cleaner Assembly, P/N SAF2S-XXXXXX3XXX. . 16
6 Conveyor Products Warning Label, P/N 23395 . . . . . . . . . . . . . . . . . . . . . . . . . 18
7 MARTIN

SQC2 Tensioning Label, P/N SQC2-10002 . . . . . . . . . . . . . . . . 18
List of Tables
Table Title Page
I Urethane Shelf Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
II MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly
Part Numbers and Quantities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
III MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly Blade Chart. . . . . 13
IV MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly
Part Numbers and Quantities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
V MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly Blade Chart. . . . . 15
VI MARTIN

SAF-2 Belt Cleaner Assembly Part Numbers and Quantities . . . . . . 17
VII MARTIN

SAF-2 Belt Cleaner Assembly Blade Chart. . . . . . . . . . . . . . . . . . . . 17
L
i
s
t

o
f

F
i
g
u
r
e
s
/
T
a
b
l
e
s
Martin Engineering M3820-10/11 1 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Introduction
General To introduce product back into the product flow, a Pre-Cleaner is installed on
the face of the head pulley. On a dual cleaner system, the Secondary Cleaner
is installed immediately following the Pre-Cleaner to remove stubborn
material left on the conveyor belt. If a Pre-Cleaner cannot be used because of
space limitations, the Secondary Cleaner is installed alone. If the material-
handling process or product could be affected by contamination from the use
of these belt cleaners, the user is responsible for taking the necessary steps to
prevent contamination. Consult Martin Engineering or a representative for
alternate belt cleaners or belt cleaner locations to use where contamination
may be an issue.
Installations
without chutework
These procedures were written for equipment that is being installed on
enclosed pulley chutework. If the pulley is not enclosed, the equipment should
be installed using the best available field resources and methods to ensure that
the critical dimensions are followed for proper installation.
Belt cleaner
inspection access
If the belt cleaner is installed on enclosed pulley chutework, a MARTIN

Inspection Door should be installed. MARTIN

Inspection Doors are

available from Martin Engineering or a representative.
References The following documents are referenced in this manual:
American National Standards Institute (ANSI) z244.1-1982, American
National Standard for Personnel Protection - Lockout/Tagout of Energy
Sources - Minimum Safety Requirements, American National Standards
Institute Inc., 1430 Broadway, New York, NY 10018.
Federal Register, Volume 54, Number 169, Part IV, 29 CFR Part 1910,
Control of Hazardous Energy Source (Lockout/Tagout); Final Rule,
Department of Labor, Occupational Safety and Health Administration
(OSHA), 32nd Floor, Room 3244, 230 South Dearborn Street,
Chicago, IL 60604.
MARTIN

SQC2 Square Mainframe Tensioners Operators Manual,

P/N M3815
I
n
t
r
o
d
u
c
t
i
o
n
Martin Engineering M3820-10/11 2 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Safety All safety rules defined in the above documents and all owner/employer safety
rules must be strictly followed when working on the belt cleaner.
DANGER
!
Do not touch or go near the conveyor belt or conveyor
accessories when the belt is running. Your body or clothing
can get caught and you can be pulled into the conveyor,
resulting in severe injury or death.
DANGER
!
Before installing, servicing, or adjusting the belt cleaner, turn
off and lock out/tag out all energy sources to the conveyor and
conveyor accessories according to ANSI standards. Failure to
do so could result in serious injury or death.
DANGER
!
If this equipment will be installed in an enclosed area, test the
gas level or dust content before using a cutting torch or
welding. Using a torch or welding in an area with gas or dust
may cause an explosion resulting in serious injury or death.
WARNING
!
Before using a cutting torch or welding the chute wall, cover
the conveyor belt with a fire retardant cover. Failure to do so
can allow the belt to catch fire.
WARNING
!
Remove all tools from the installation area and conveyor belt
before turning on the conveyor. Failure to do so can cause
serious injury to personnel or damage to the belt and
conveyor.
WARNING
!
Mainframe with blade can be heavy and may require two
people to lift. Attempting to lift the belt cleaner without
assistance could result in injury.
I
n
t
r
o
d
u
c
t
i
o
n
Martin Engineering M3820-10/11 3 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Urethane shelf life
IMPORTANT
Urethane put in service after exceeding its shelf life may wear
differently and deteriorate quicker than normal urethane.
NOTE
Code Date is written near bottom of blade as mm/dd/yy-x. In
addition to or in place of this date, you may see an imprinted
date medallion similar to the example shown. In this example,
10 stands for the year 2010. The small circles represent the
months of the year and are punched to indicate what month
the blade was produced. If code date on your blade(s) is not
legible or is missing, contact Martin Engineering or a
representative.
Table I. Urethane Shelf Life
10
Blade Color Shelf Life
Blue 1 Year from Code Date
Brown 2 Years from Code Date
Clear 1 Year from Code Date
Green 2 Years from Code Date
Maximizer (orange) 1 Year from Code Date
Orange (A-9) 1 Year from Code Date
I
n
t
r
o
d
u
c
t
i
o
n
Martin Engineering M3820-10/11 4 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Before Installing Belt Cleaner
IMPORTANT
The delivery service is responsible for damage occurring in
transit. Martin Engineering CANNOT enter claims for
damages. Contact your transportation agent for more
information.
1. Inspect shipping container for damage. Report damage to delivery service
immediately and fill out delivery services claim form. Keep any damaged
goods subject to examination.
2. Remove belt cleaner assembly from shipping container.
3. If anything is missing contact Martin Engineering or a representative.
WARNING
!
Before installing equipment, turn off and lock out/ tag out all
energy sources to the conveyor and conveyor accessories
according to ANSI standards. Failure to do so could result in
serious injury or death.
4. Turn off and lock out/tag out energy source according to ANSI standards
(see References).
DANGER
!
If this equipment will be installed in an enclosed area, test the
gas level or dust content before using a cutting torch or
welding. Using a torch or welding in an area with gas or dust
may cause an explosion resulting in serious injury or death.
5. If using a cutting torch or welding, test atmosphere for gas level or dust
content. Cover conveyor belt with fire retardant cover.
IMPORTANT
Center the belt cleaner blades to clean an area narrower than
the conveyor belt width. This allows for side-to-side
movement of the belt and prevents damage to the belt edge.
B
e
f
o
r
e

I
n
s
t
a
l
l
a
t
i
o
n
Martin Engineering M3820-10/11 5 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Installing Belt Cleaner Assembly
Figure 1. Mounting Locations
4.56
(116)
6.12
(155)
min.
2.65 (67) min.
Keep Holes
Vertical
4.50
(114)
10
.13 (3)
Above
Belt
Bottom
11.00
(279)
6.00
(152)
2 x .625 (16)
Keep
Parallel
1.50 (38)
Hole Range
5.72 (145)
min.
Keep Holes
Vertical
1.88
(48)
10
.13 (3)
Above
Belt
Bottom
4.53
(115)
min.
4.56
(116)
Keep Parallel
1.75 (44)
Hole Range
6.00
(152)
11.00
(279)
2.00 (51) min.
4.00 (102) max.
2.00 (51) min.
4.00 (102) max.
8.04
(204)
8.04
(204)
2 x .625 (16)
MARTIN

SQC2 Blade and MARTIN

SAF-2 Reversing Blade Mounting Location

MARTIN

SAF-2 Blade Mounting Location

Left Side Mounting Right Side Mounting
Left Side Mounting Right Side Mounting
2.0 (51) min.
4.0 (102) max.
1.62
(41)
2.0 (51) min.
4.0 (102) max.
1.62
(41)
11.0
(279)
6.0
(152)
2.62
(67)
5/8
(16)
4.50
(114)
5.00 (127) min.
6.25 (159) max.
11.0
(279)
6.0
(152)
2.62
(67)
5/8
(16)
4.50
(114)
5.00 (127) min.
6.25 (159) max.
0.25 (6) min.
2.25 (57) max.
6.25 (159) min.
8.25 (210) max.
I
n
s
t
a
l
l
a
t
i
o
n
Martin Engineering M3820-10/11 6 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

NOTE
Solid backing of the blade is essential to ensure proper
operation and efficient cleaning. Install the cleaner adjacent to
the head pulley or a flat pressure roller to obtain best cleaning
results.
NOTE
For installation on enclosed head pulley chutework, draw all
dimension lines on chute wall. In applications where head
pulley is not enclosed, use the best available field resources
and/or methods to ensure that these critical dimensions are
followed for a proper installation.
Marking chute
cutouts
1. Mark the chute cutout and mount hole locations as shown in Figure 1.
Repeat on both sides of chute, ensuring cutouts are accurately aligned
with each other.
2. At the selected mounting position, cut the cleaner access slots and drill
the mount holes in each side of the chute. Dress and de-burr the holes and
cutouts.
Figure 2. Removing and Installing Blade Cartridge
Removing blade 1. Remove lock pin from operator side of mainframe and blade.
2. Pull blade away from stationary pin on far side of mainframe and remove
from mainframe. Make sure lock pin remains attached to mainframe.
Stationary pin
Blade
Far side
Operator side
Mainframe
Lock pin
I
n
s
t
a
l
l
a
t
i
o
n
Martin Engineering M3820-10/11 7 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Installing
tensioner
1. Install tensioner according to MARTIN

Square Mainframe Tensioner

Operators Manual, P/N M3815.
2. If using MARTIN

Inspection Door, install according to MARTIN

Inspection Door Operator's Manual, P/N M3127.
Installing blade 1. Slide blade cartridge onto mainframe with blade positioned as shown in
Figure 1. Push far side end of blade against stationary pin until it locks.
2. Insert lock pin in mainframe and cartridge.
3. Make sure blades are centered on belt and mainframe is parallel to belt.
4. Tension belt cleaner according to MARTIN

Square Mainframe Tensioner

Operators Manual, P/N M3815.
I
n
s
t
a
l
l
a
t
i
o
n
Martin Engineering M3820-10/11 8 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

After Installing Belt Cleaner
1. Thoroughly wipe chute wall clean above tensioner.
2. Place Conveyor Products Warning Label (P/N 23395) on outside chute
wall visible to belt cleaner operator.
WARNING
!
Failure to remove tools from installation area and conveyor
belt before turning on energy source can cause serious injury
to personnel and damage to belt.
DANGER
!
Do not touch or go near conveyor belt or conveyor accessories
when conveyor belt is running. Body or clothing can get
caught and pull body into conveyor belt, causing severe injury
or death.
3. Turn on conveyor belt for 1 hour, then turn off.
DANGER
!
Before installing, servicing, or adjusting the belt cleaner/
tensioner, turn off and lock out/tag out all energy sources to
the conveyor and conveyor accessories according to ANSI
standards. Failure to do so could result in serious injury or
death.
4. Make sure all fasteners are tight. Tighten if necessary.
5. Make sure cleaner is not changing belt line. If it is, install belt support
ahead of blade-to-belt contact point (Secondary Cleaner).
6. Inspect belt cleaner for the following:
Wear. (A small amount of break-in wear may be found. This will
stop once blades wear to conveyor belt contour.)
Material buildup. (No material between blades and return side of
conveyor belt should be found.)
7. If wear, material buildup, or some other problem exists, see
Troubleshooting.
A
f
t
e
r

I
n
s
t
a
l
l
a
t
i
o
n
Martin Engineering M3820-10/11 9 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Weekly Maintenance
IMPORTANT
Read entire section before beginning work.
NOTE
Maintenance inspection should be performed no less than
weekly. Some applications may require more frequent
maintenance inspections.
DANGER
!
Before installing, servicing, or adjusting the belt cleaner/
tensioner, turn off and lock out/tag out all energy sources to
the conveyor and conveyor accessories according to ANSI
standards. Failure to do so could result in serious injury or
death.
1. Remove any material from belt cleaner.
2. Make sure all fasteners are tight. Tighten if necessary.
3. Check tension on cleaner. Re-tension if necessary.
4. Wipe all labels clean. If labels are not readable, contact Martin
Engineering or a representative for replacements.
5. Check blades for excessive wear. Replace if necessary.
6. Remove equipment from service if there is any indication it is not
functioning properly. Call Martin Engineering or a representative for
assistance. Do NOT return equipment to operation until the cause of the
problem has been identified and corrected.
WARNING
!
Failure to remove tools from installation area and conveyor
belt before turning on energy source can cause serious injury
to personnel and damage to belt.
7. Remove all tools from maintenance area.
DANGER
!
Do not touch or go near conveyor belt or conveyor accessories
when conveyor belt is running. Body or clothing can get
caught and pull body into conveyor belt, causing severe injury
or death.
8. Start conveyor belt.
W
e
e
k
l
y

M
a
i
n
t
e
n
a
n
c
e
Martin Engineering M3820-10/11 10 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Troubleshooting
NOTE
Conveyor equipment such as conveyor belt cleaners are subject to a wide variety of bulk materials
characteristics and often have to perform under extreme operating or environmental conditions. It is
not possible to predict all circumstances that may require troubleshooting. Contact Martin
Engineering or a representative if you are experiencing problems other than those listed in the
Troubleshooting chart above. Do not return the equipment to operation until the problem has been
identified and corrected.
Installation
checklist
If after taking the corrective actions suggested under Troubleshooting you
are still experiencing problems, check for the following:
Symptom Corrective Action
Insufficient cleaning and
carryback.
Tension of cleaner on belt is set too low or too high. Increase or
decrease tensioner setting.
Blades are worn. Check blades and replace if necessary.
Noise or vibration.
Tension is not sufficient or is set too high. Correct tension as
necessary. If this does not correct problem, blade urethane may not
match application. Contact Martin Engineering or representative.
High blade wear rate. Tension of cleaner on belt is set too high. Reduce tensioner setting.
Unusual wear or damage to
blades.
Check belt splice(s) and repair as necessary.
Bent or broken mainframe
or support frame due to
blade slipping through.
If blades are worn to or past the wear line, replace blades. If blades
are not worn, check mainframe location.
Corrosion or chemical
degradation.
Blade urethane may not match application. Contact Martin
Engineering or representative.
Installation Checklist
Pre-Cleaner mainframe is proper distance from belt surface on both ends of mainframe.
Pre-Cleaner blade tip is at or below horizontal center line of pulley and does not lie in path
of material flow.
Secondary Cleaner blade tip is 1 in. (25 mm) past vertical center line of pulley.
Secondary Cleaner is not changing belt line.
Blades are centered on belt.
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Martin Engineering M3820-10/11 11 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Part Numbers
MARTIN

SQC2 Assembly
P/N SQC2S-XXXXXXXXXX. See Figures 3 and 4. Includes blade cartridge,
mainframe and tensioners.
MARTIN

SAF-2
Assembly
P/N SAF2S-XXXXXXX3XX. See Figure 5. Includes blade cartridge,
mainframe and tensioners.
MARTIN

Tensioners
MARTIN

SQC2 Square Mainframe Tensioners: P/N 38664.
MARTIN

SQC2 Blade
Cartridges
P/N SQC2SC-XXXXXXXXX. Includes replacement blades.
P/N SQC2SC-XXXXXX3XX. Includes replacement blades.
MARTIN

SAF-2 Blade
Cartridges
P/N SAF2SC-XXXXXX3XX. Includes replacement blades.
Miscellaneous MARTIN

Heavy-Duty Hanger Mount Assembly: P/N 34233-HD. Used to
mount MARTIN

SQC2 Tensioners onto stringer instead of onto chute

wall.
XXXXX-XXXXXXXX X X NOMENCLATURE
P/N Prex
Belt Width (inches)
Blade Type
Belt Cleaning Width (inches)
Blade Buffer Type
Mainframe Option
Tensioner Option
Additional Options
P/N PREFIX
SQC2S: SQC2 Assembly
SAF2S: SAF-2 Assembly
BLADE TYPE
(SQC2 STYLE)

G: Acid-Resistant for belts
with clips
H: Acid-Resistant
R: General Applications and
Reversing BeltsTungsten
Carbide
T: Tungsten Carbide

U: Urethane
: No Blades
BLADE BUFFER TYPE/
URETHANE COLOR
MR: Molded Rubber
FR: Flame-Retardant Rubber
: No Buffers
O3: Orange Urethane
B3: Brown Urethane
G3: Green Urethane

MAINFRAME OPTIONS
P: Painted Mainframe
S: Stainless Mainframe
TENSIONER OPTIONS
T: Tensioner included
: No Tensioner
S: 316 SS
ADDITIONAL OPTIONS
: None
D: Dust-Tight Steel Cover
Door
N3: Navy Blue Urethane
BLADE TYPE
(SAF-2 STYLE 3-IN. WIDE)

R: Reversing BeltsUrethane
: No Blades
BLADE CLEANING WIDTH
Full belt width or Approx.
6 inches less belt width.
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 12 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Figure 3. MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly,

P/N SQC2S-XXXXXXXXXX
* XX indicates belt width (available in full belt width or belt width less 6 in.).
Item Description Part Number Qty
1 Mainframe 38657-XX* 1
2 Blade Cartridge SQC2S-35696-XX* 1
3 Pin Slotted Spring 1/2 X 3 ZP 33840 1
4 Pin Snap Lock 7/16 33841 1
5 (NS) Urethane Shipping Pin 35846 1
6 Cable Aircraft 1/8 Dia. 100107 2 ft
7 Cable Clip for 1/8 Dia. Cable 23481 2
8 Blade Assembly Table III Table II
9 Screw HHC 5/16-18NC X 1-1/2 SS SP04436-30 Table II
10 Washer Flat 5/16 Narrow SS 37724 Table II
11 Washer Lock Helical Spring 5/16 SS 33055 Table II
12 Nut Hex 5/16-18NC Narrow SS 37723 Table II
13 Label Martin Products 38048 2
14 (NS)
MARTIN

SQC2 Tensioner
38664 1
15 (NS) Manual Operators M3820 1
16 (NS) Split Dust-Tight Door Assembly 38014-SQCS 1
8
10
12
11
9
2
13
1
3
4
7
6
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 13 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Table II. MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly

Part Numbers and Quantities
Table III. MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly Blade Chart

Part No.
Qty
Item 8
Qty
Items 9-12
SQC2S-XXX12XXXXX 2 4
SQC2S-XXX18XXXXX 3 6
SQC2S-XXX24XXXXX 4 8
SQC2S-XXX30XXXXX 5 10
SQC2S-XXX35XXXXX 6 12
SQC2S-XXX41XXXXX 7 14
SQC2S-XXX47XXXXX 8 16
SQC2S-XXX53XXXXX 9 18
SQC2S-XXX59XXXXX 10 20
SQC2S-XXX65XXXXX 11 22
SQC2S-XXX71XXXXX 12 24
SQC2S-XXX77XXXXX 13 26
SQC2S-XXX83XXXXX 14 28
SQC2S-XXX89XXXXX 15 30
Part No. P/N Item 8 Color General Application
SQC2S-XXGXXXXXXX SC-XXG ORANGE Acid-Resistant Belt with Clips
SQC2S-XXHXXXXXXX SC-XXH ORANGE Acid-Resistant
SQC2S-XXRXXXXXXX SC-XXR ORANGE General Conditions Reversing Belt with Clips
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 14 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Figure 4. MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly

with 3-in. MARTIN

SAF-2 Style Blades, P/N SQC2S-XXXXXX3XXX

* First XX indicates belt width. Last X indicates material: mild steel (Blank) or stainless steel (S).
**First XX indicates belt width (available in full belt width or belt width less 6 in.). Last X indicates cartridge length: belt width
less 2 in. (Blank) or full belt width (F).
Item Description Part Number Qty
1 Mainframe 38657-XXX* 1
2 Blade Cartridge SQC2S-35696-XX3X** 1
3 Pin Slotted Spring 1/2 X 3 ZP 33840 1
4 Pin Snap Lock 7/16 33841 1
5 (NS) Urethane Shipping Pin 35846 1
6 Cable Aircraft 1/8 Dia. 100107 2 ft
7 Cable Clip for 1/8 Dia. Cable 23481 2
8 Urethane Blade Table V Table IV
9 Blade with Carbide Tip Table V Table IV
10 Backing Plate 38280 Table IV
11 Screw HHC 5/16-18NC x 2-1/4 SS 38040 Table IV
12 Washer Flat 5/16 Narrow SS 37724 Table IV
13 Nut Hex Elastic Lock 5/16-18NC SS 33054 Table IV
14 Label Martin Products 38048 2
15 (NS)
MARTIN

SQC2 Tensioner
38664 1
16 (NS) Manual Operators M3820 1
17 (NS) Split Dust-Tight Door Assembly 38014-SQCS 1
8
10
12
13
11
2
14
1
3
4
7
6
9
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 15 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Table IV. MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly

Part Numbers and Quantities
*Quantity represents total blades on the cartridge. Each cartridge has a minimum of two urethane blades, one
on each end of the cartridge. The blades in between are available in either urethane or tungsten carbide.
Table V. MARTIN

SQC2 Square Mainframe Belt Cleaner Assembly Blade Chart

Part No.
Qty
Items 8 & 9
combined*
Qty
Item 10
Qty
Items 11-13
SQC2S-XXX12X3XXX 4 2 4
SQC2S-XXX18X3XXX 6 3 6
SQC2S-XXX24X3XXX 8 4 8
SQC2S-XXX30X3XXX 10 5 10
SQC2S-XXX36X3XXX 12 6 12
SQC2S-XXX42X3XXX 14 7 14
SQC2S-XXX48X3XXX 16 8 16
SQC2S-XXX54X3XXX 18 9 18
SQC2S-XXX60X3XXX 20 10 20
SQC2S-XXX66X3XXX 22 11 22
SQC2S-XXX72X3XXX 24 12 24
SQC2S-XXX78X3XXX 26 13 26
SQC2S-XXX84X3XXX 28 14 28
SQC2S-XXX90X3XXX 30 15 30
SQC2S-XXX96X3XXX 32 16 32
Part No. P/N Item 8 P/N Item 9 Color
SQC2S-XXRXXB3XXX 38718-URBR Brown
SQC2S-XXRXXG3XXX 38718-URGR Green
SQC2S-XXRXXN3XXX 38718-URNB Navy Blue
SQC2S-XXRXXO3XXX 38718-UR Orange
SQC2S-XXTXXB3XXX 38718-UBR 38718-TBR Brown
SQC2S-XXTXXG3XXX 38718-UGR 38718-TGR Green
SQC2S-XXTXXN3XXX 38718-UNB 38718-TNB Navy Blue
SQC2S-XXTXXO3XXX 38718-U 38718-T Orange
SQC2S-XXUXXB3XXX 38718-UBR Brown
SQC2S-XXUXXG3XXX 38718-UGR Green
SQC2S-XXUXXN3XXX 38718-UNB Navy Blue
SQC2S-XXUXXO3XXX 38718-U Orange
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 16 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Figure 5. MARTIN

SAF-2 Belt Cleaner Assembly P/N SAF2S-XXXXXX3XXX

* First XX indicates belt width. Last X indicates material: mild steel (Blank) or stainless steel (S).
**First XX indicates belt width (available in full belt width or belt width less 6 in.).
Item Description Part Number Qty
1 Mainframe 38657-XXX* 1
2 Blade Cartridge 33843S-XX** 1
3 Pin Slotted Spring 1/2 X 3 ZP 33840 1
4 Pin Snap Lock 7/16 33841 1
5 (NS) Urethane Shipping Pin 35846 1
6 Cable Aircraft 1/8 Dia. 100107 2 ft
7 Cable Clip for 1/8 Dia. Cable 23481 2
8 End Stop 34048 2
9 Urethane Blade Table VII Table VI
10 Blade with Carbide Tip Table VII Table VI
11 Label Martin Product 38048 2
12 (NS)
MARTIN

SQC2 Tensioner Assembly

38664 1
13 (NS) Manual Operators M3820 1
14 (NS) Dust Tight Split Cover Door Assembly 38014-SQCS 1
15 Plug for 2.5 Square Tube 34896-02 2
16 Screw SHS1/2-13NC x 2 SS 22763-06 2
8
10
15
16
2
11
1
3
4
6
7
9
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 17 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Table VI. MARTIN

SAF-2 Belt Cleaner Assembly Part Numbers and Quantities

*Quantity represents total blades on the cartridge. Each cartridge has a minimum of two urethane blades, one
on each end of the cartridge. The blades in between are available in either urethane or tungsten carbide.
Table VII. MARTIN

SAF-2 Belt Cleaner Assembly Blade Chart

Part No.
Qty
Items 9 & 10
combined*
SAF2S-XXX12X3XXX 4
SAF2S-XXX18X3XXX 6
SAF2S-XXX24X3XXX 8
SAF2S-XXX30X3XXX 10
SAF2S-XXX36X3XXX 12
SAF2S-XXX42X3XXX 14
SAF2S-XXX48X3XXX 16
SAF2S-XXX54X3XXX 18
SAF2S-XXX60X3XXX 20
SAF2S-XXX66X3XXX 22
SAF2S-XXX72X3XXX 24
SAF2S-XXX78X3XXX 26
SAF2S-XXX84X3XXX 28
SAF2S-XXX90X3XXX 30
SAF2S-XXX96X3XXX 32
Part No. P/N Item 9 P/N Item 10 Color
SAF2S-XXTXXB3XXX 38718-UBR 38718-TBR Brown
SAF2S-XXTXXG3XXX 38718-UGR 38718-TGR Green
SAF2S-XXTXXN3XXX 38718-UNB 38718-TNB Navy Blue
SAF2S-XXTXXO3XXX 38718-U 38718-T Orange
SAF2S-XXUXXB3XXX 38718-UBR Brown
SAF2S-XXUXXG3XXX 38718-UGR Green
SAF2S-XXUXXN3XXX 38718-UNB Navy Blue
SAF2S-XXUXXO3XXX 38718-U Orange
P
a
r
t

N
u
m
b
e
r
s
Martin Engineering M3820-10/11 18 MARTIN

SAF-2 and MARTIN

SQC2 Square Mainframe Belt Cleaners

Figure 6. Conveyor Products Warning Label, P/N 23395
Figure 7. MARTIN

SQC2 Tensioning Label, P/N SQC2-10002

Lock out and/or tag out all energy sources to
Cierre y/o rotule todas las fuentes de energa al
Label P/N 23395
conveyor system and loading system before
performing any work on conveyor or conveyor
accessories. Failure to do so could result in
severe injury or death.
sistema transportador y al sistema de carga antes
de realizar cualquier trabajo en el transportador
o sus accesorios. El no hacerlo puede resultar
en heridas serias o muerte.
ADVERTENCIA
WARNING
!
!
P
a
r
t

N
u
m
b
e
r
s
Any product, process, or technology described here may be the subject of intellectual property rights reserved by
Martin Engineering Company. Trademarks or service marks designated with the symbol are registered with the U.S.
Patent and Trademark Office and may be proprietary in one or more countries or regions. Other trademarks and
service marks belonging to Martin Engineering Company in the United States and/or other countries or regions may
be designated with the TM and SM symbols. Brands, trademarks, and names of other parties, who may or may
not be affiliated with, connected to, or endorsed by Martin Engineering Company, are identified wherever possible.
Additional information regarding Martin Engineering Companys intellectual property can be obtained at
www.martin-eng.com/trademarks.
One Martin Place
Neponset, IL 61345-9766 USA
800-544-2947 or 309-852-2384
FAX: 800-814-1553
www.martin-eng.com
We Make Your Bulk Materials Handling
Cleaner, Safer and More Productive
Through Personalized Performance.
Form No. M3820-10/11
2010, 2011 MARTIN ENGINEERING COMPANY. All rights reserved.
Operators Manual
M3820
MARTIN

SAF-2

&
MARTIN

SQC2

Square Mainframe Belt Cleaners