Wire Ropes Drive Mechanism For Reciprocating Linear Motion

TOPIC: - Wire rope drive mechanism for reciprocating linear motion
SUBMITTED TO: SUBMITTED BY:
Mr. SUMIT SHOOR
T. SACHIN KUMAWAT SECTION: M3RO6 ROLL NO.: B36 REGD.NO: 11005617
Wire ropes drive mechanism for reciprocating linear motion
introduction
Wire rope is a type of rope which consists of several strands of metal wire laid or 'twisted') into a helix. Initiallywrought iron wires were used, but today steel is the main material used for wire ropes.Historically wire rope evolved from steel chains which had a record of mechanical failure. While flaws in chain links or solid steel bars can lead to catastrophic failure, flaws in the wires making up a steel cable are less critical as the other wires easily take up the load. Friction between the individual wires and strands, as a consequence of their twist, further compensates for any flaws.
Wire rope construction

Wires
Steel wires for wire ropes are normally made of non-alloy carbon steel with a carbon content wire cross-section is reduced in stages, for example in seven stages from 6 to 2mm diameter. By the drawing process the nominal strength reaches between 1370 and 2450 N/mm. The run over sheaves with relatively small diameters. very high strength of the rope wires enables wire ropes to support large tensile forces and to of 0.4 to 0.95%. The wires are patented [6](heat process). In the following drawing process, the
Strands
In the so-called cross lay strands, the wires of the different layers cross each other. In the mostly used parallel lay strands, the lay length of all the wire layers is equal and the wires of any two superimposed layers are parallel, resulting in linear contact. The wire of the outer layer is supported by two wires of the inner layer. These wires are neighbours along the whole length of the strand. Parallel lay strands are made in one operation. The endurance of wire
ropes with this kind of strand is always much greater than of those (seldom used) with cross lay strands. Parallel lay strands with two wire layers have the construction Filler, Seale or Warrington.
Spiral ropes
In principle, spiral ropes are round strands as they have an assembly of layers of wires laid that of the outer layer. Spiral ropes can be dimensioned in such a way that they are nonrotating which means that under tension the rope torque is nearly zero. The open spiral rope consists only of round wires. The half-locked coil rope and the full-locked coil rope always have a centre made of round wires. The locked coil ropes have one or more outer layers of helically over a centre with at least one layer of wires being laid in the opposite direction to
profile wires. They have the advantage that their construction prevents the penetration of dirt and water to a greater extent and it also protects them from loss of lubricant. In addition, they have one further very important advantage as the ends of a broken outer wire cannot leave the rope if it has the proper dimensions.
Stranded ropes
Left-hand ordinary lay (LHOL) wire rope (close-up). Right-hand lay strands are laid into a lefthand lay rope.Right-hand Lang's lay (RHLL) wire rope (close-up). Right-hand lay strands are laid into a right-hand lay rope.Stranded ropes are an assembly of several strands laid helically in one or more layers around a core. Most types of stranded ropes only have one strand layer over the core (fibre core or steel core). The lay direction of the strands in the rope can be right (symbol Z) or left (symbol S) and the lay direction of the wires can be right (symbol z) or left (symbol s). This kind of rope is called ordinary lay rope if the lay direction of the wires in the outer strands is in the opposite direction to the lay of the outer strands themselves. If both the wires in the outer strands and the outer strands themselves have the same lay direction, the rope is called a lang lay rope (formerly Alberts lay or Langs lay). Multi-strand ropes are all centre. The direction of the outer strands is opposite to that of the underlying strand layers. Ropes with three strand layers can be nearly non-rotating. Ropes with two strand layers are mostly only low-rotating.
more or less resistant to rotation and have at least two layers of strands laid helically around a
Rope drive
There are technical regulations for the rope installations not exceeding a given tensile force and not falling short of a given diameter ratio D/d of sheave and rope diameters. A general used besides the technical regulations) calculate the five limits

drives of cranes, elevators, rope ways and mining dimensioning method of rope drives (and
Working cycles up to rope discarding or breakage (mean or 10% limit) Donandt force (yielding tensile force for a given bending diameter ratio D/d) Rope safety factor, minimum breaking force (ability to resist extreme forces) Discarding number of wire breaks (detection to need rope replacement) Optimal rope diameter (economic reasons)
Mechanism of wire ropes

A drive mechanism for providing reciprocating, liner motion for a movable work piece relative to a stationary work piece is provided. The drive system includes a motor rotating a drum in forward and reverse directions about a first axis. The motor and drum are fixedly mounted with respect to the stationary work piece, such as to a housing or other structure. The system further includes an elongate, substantially non-flexible cable having a first and second ends fixed with respect to the stationary work piece. The cable further includes an intermediate portion extending between the first and second ends, with the intermediate portion being wound around the drum. First and second bearings are provided which are mounted to the movable work piece. The first bearing is positioned relative to the cable such that the intermediate portion of the cable is wound over the first bearing, and with the first bearing being positioned between the first end of the cable and the drum. The second bearing is positioned relative to the cable such that the intermediate portion of the cable is wound over the second bearing with the second bearing being positioned between the drum and the second end of the cable. Rotation of the drum in either clockwise or counterclockwise directions causes the cable to move the first and second bearings back and forth relative to the drum, thereby causing linear, reciprocating movement of the moveable work piece relative to the stationary work piece.

Wire Ropes Drive Mechanism For Reciprocating Linear Motion

Uploaded by

Copyright:

Available Formats

Wire Ropes Drive Mechanism For Reciprocating Linear Motion

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wire Ropes Drive Mechanism For Reciprocating Linear Motion

Uploaded by

Copyright:

Available Formats

TOPIC: - Wire rope drive mechanism for reciprocating linear motion

SUBMITTED TO: SUBMITTED BY:

Mr. SUMIT SHOOR

T. SACHIN KUMAWAT SECTION: M3RO6 ROLL NO.: B36 REGD.NO: 11005617

Wire ropes drive mechanism for reciprocating linear motion

Wire rope construction

Mechanism of wire ropes

You might also like