Behaviour and Design of Flexural Members (Beams) (AS 4100 - Section 5)
Behaviour and Design of Flexural Members (Beams) (AS 4100 - Section 5)
e
= (b/t)
250
f
y
(4.4)
where b = the clear width and t = the element thickness
This plate slenderness is then checked against two limits, the yield limit
ey
and the plasticity
limit
ep
to determine whether elastic or inelastic local buckling will occur in the plate
elements. These slenderness limits are given in Table 5.2 of AS 4100. Table 5.2 is reproduced
here as Table 4.1 for the sake of completeness.
If all the plate elements have
e
values less than the corresponding
ep
values given in Table
5.2 of AS 4100, the section will not be subjected to any local buckling effects (elastic or
inelastic). Therefore the section will develop its full plastic moment capacity M
p
, and is
called a COMPACT section. The Effective Section Modulus Z
e
in this case is given by:
Z
e
= Lesser of S or 1.5 Z (4.5)
Table 4.1 Values of Plate Element Slenderness Limit (
ey
and
ep
)
Plate Element Type Longitud.
edges
supported
Residual
stresses
(see Notes)
Plasticity
limit
(
ep
)
Yield
limit
(
ey
)
Deformn.
Limit (
ed
)
SR 10 16 35
Flat element One HR 9 16 35
subject to (outstand) LW, CF 8 15 35
Uniform HW 8 14 35
compression SR 30 45 90
Both HR 30 45 90
LW, CF 30 40 90
HW 30 35 90
Flat element subject to max. SR 10 25 -
compn. at unsupported
edge,
One HR 9 25 -
zero stress or tension (outstand) LW, CF 8 22 -
at supported edge HW 8 22 -
Flat element subject to
Compression at one edge, Both Any 82 115 -
Tension at the other
SR 50 120 -
Circular hollow sections HR, CF 50 120 -
LW 42 120 -
HW 42 120 -
Notes. 1. SR Stress Relieved
HR Hot-Rolled or Hot-Finished
CF Cold-Formed
LW Lightly Welded longitudinally
HW Heavily Welded longitudinally
2. Welded members whose compressive residual stresses are less than 40 MPa may
be considered to be lightly welded.
4-5
3. For elements with
e
>
ed
noticeable deformations may occur under service
loading
For standard sections use BHP Handbook or AISC design capacity tables;
For nonstandard sections calculate S and Z, then Z
e
. The S component for web elements is
bd
2
/4 whereas the S component for flanges can be approximately taken as flange area x the
distance between the flange and the section centroid.
If anyone of the plate elements
e
exceeds the plastic limit
ep
, but not the yield limit
ey
(
ep
<
e
ey
), the section will be subjected to inelastic local buckling. The section will reach
first yield moment, but not the full plastic moment capacity M
p
. The section capacity M
s
is
between M
y
(Yield Moment) and M
p
(Plastic Moment) (see Figure 4.3); The section is called
a NON-COMPACT section. The Effective Section Modulus Z
e
in this case will therefore be
between Z and Z
c,
which is Z
e
of compact section (lesser of S or 1.5Z). The Z
e
of non-
compact section is obtained by interpolating between Z (corresponds to
ey
) and Z
c
(corresponds to
ep
).
Z
e
= Z + (Z
c
-Z)
ey e
ey ep
(4.6)
The ratio
ey e
ey ep
ey
e
(4.7a)
for flat plate elements in uniform Compression;
Examples of this case are the compression flange elements of I-section and Box-section
subject to major axis bending.
Z
e
= Z (
ey
e
)
2
(4.7b)
for flat plate elements with maximum compression at an unsupported edge and zero stress or
tension at the other edge. Examples of this case are I-section subject to minor axis bending
and inverted T-section subject to major axis bending.
The effective section modulus can be obtained conservatively by applying reductions to the
whole section, but a more accurate answer can be obtained if the reductions are applied to the
section modulus contributed by the slender elements only as appropriate and not to the whole
section. Example problems in this section illustrate this method.
Note that BHPs standard sections are either compact or non-compact (not slender) and their
Effective section modulus Z
ex
and Z
ey
values are listed in the BHP handbook and AISC design
capacity tables. Therefore no other calculations are needed. Section capacities of these
beams in bending are simply obtained by the product f
y
x Z
e
.
Figure 4.3 illustrates the variation in section moment capacity as a function of plate
slenderness and type of section (compact versus non-compact versus slender).
For circular hollow sections, the section slenderness
s
=
250
d
o
250
f
y
(4.8)
where d
o
= the outside diameter
If
s
exceeds the section yield slenderness limit
sy
Z
e
= Lesser of Z (
sy
/
s
) and Z (2
sy
/
s
)
2
(4.9)
4-7
The values of
sy
are to be taken as the values of
ey
given in Table 5.2 of AS 4100 (see Table
4.1 in this set of notes).
For sections with holes that reduce either of the flange areas by not more than
100 {1-[f
y
/(0.85f
u
)]}%, there is little effect on moment capacity and the gross section can be
used to calculate the elastic and plastic section moduli.
4.4.2 Example Problems on Local Buckling and Yielding of Beams
Example Problem No.1
What is the section moment capacity of 530UB92.4 Grade 300 beams about the major
principal axis (x)?
Example Problem No.2
What is the section moment capacity of 200UC52.2 Grade 300 beams about the minor
principal axis (y)?
Example Problem No.3
Figure 4.4 shows a lightly welded box-girder made of Grade 350 steel. What is its section
moment capacity about the major principal axis (x)?
t
w
= 10 mm f
yw
= 360 MPa
t
f
= 12 mm f
yf
= 360 MPa
Figure 4.4 Welded Box-girder in Example Problem No.3
Example Problem No.4
Figure 4.5 shows a lightly welded I-section beam made of Grade 350 steel. What is its section
360 mm
400 mm
4-8
moment capacity about the major principal axis (x)?
t
w
= t
f
=10 mm f
y
= 360 MPa
Figure 4.5 Welded I-section in Example Problem No.4
Example Problem No.5
Figure 4.6 shows a lightly welded plate girder made of Grade 350 steel. What is its section
moment capacity about the major principal axis (x)?
t
w
= 10 mm f
yw
= 360 MPa
t
f
= 25 mm f
yf
= 340 MPa
Figure 4.6 Welded Plate Girder in Example Problem No.5
Example Problem No.6
Figure 4.7 shows a welded plate girder made of Grade 350 steel. What is its section moment
capacity about the major principal axis (x)?
t
w
= 10 mm f
yw
= 360 MPa
t
f
= 15 mm f
yf
= 350 MPa
400 mm
400 mm
300 mm
1500 mm
4-9
Figure 4.7 Welded Plate Girder in Example Problem No.6
Example Problem No.7
How do you calculate the section moment capacity of an I-section beam about the minor
principal axis (y) if its flanges are slender.
Example Problem No.8
What is the section moment capacity of a Grade 350 1500 x 10 CHS?
450 mm
1500 mm
4-10
4.4.3 Global Buckling and Member Moment Capacity M
b
The Nominal Member Moment Capacity M
b
accounts for overall flexural-torsional
buckling (global buckling) of beams. Sections 5.3 to 5.6 of AS 4100 give the design rules
required to calculate the member capacity of beam segments subject to various restraints and
loading conditions. A segment in a member subjected to bending is the length between
adjacent cross-sections, which are fully or partially restrained, or the length between an
unrestrained end and the adjacent cross-section, which is fully or partially restrained (see
Figure 4.8). In beam design, each such segment has to be checked individually for possible
buckling failure as it depends very much on the end restraint and loading conditions.
The segments with full lateral restraint will not be subjected to global buckling effects, and
therefore, their capacity will not be reduced, ie. M
b
= M
s
10mm
min
(a) Continuous lateral restraint
(b) Intermediate lateral restraints
Figure 4.8 Segments and types of restraints
When segments have continuous lateral restraint at the critical flange or continuous lateral
restraints with both ends fully or partially restrained according to Clause 5.3.2.2 of AS 4100
(Figure 4.8a), or have intermediate lateral restraints at the critical flange with limited sub-
segment lengths and both restrained ends (Figure 4.8b) according to Clause 5.3.2.3, or have
full or partial restraints at both ends with limited lengths according to Clause 5.3.2.4, they can
be considered fully laterally restrained. A simple example for continuous lateral restraint
Concrete slab
4-11
occurs in the case when the compression flange of a beam is connected to a concrete slab
(Figure 4.8a).
The critical flange at any cross-section is considered the flange that deflects the farther during
buckling in the absence of any restraint at that section (Clause 5.5). Hence it is the
compression flange for the segment with both ends restrained whereas it is the top flange for
the segment with one end unrestrained under gravity loads (bottom flange for wind uplift).
4.4.3.1 Member Capacity of Segments without Full Lateral Restraint
A beam segment made of a compact section and that is fully laterally restrained would not fail
until well after the onset of yielding, ie. it will reach the full plastic moment capacity M
p
. As
stated in the last section, full lateral restraint can be provided by connecting the top flange to a
concrete slab, or by restraints at sufficiently close intervals. In addition, twisting of the beam
section at the supports must also be prevented (torsional restraint). However, a large
proportion of beam segments fail before this due to either local buckling of compression plate
elements or lateral buckling with twisting of the whole beam segment (global buckling known
as lateral torsional or flexural torsional buckling). The reduction to section capacity due to
local buckling of compression plate elements has been explained already in Section 4.4.1.
This section therefore describes the reduction in the member capacity of segments without
full lateral restraint due to lateral torsional buckling.
4.4.3.2 Lateral torsional buckling
Figure 4.2(b) shows the lateral torsional buckling of a beam segment bending about its major
principal axis. In this buckling mode, the beam buckles out-of-plane by deflecting laterally
and twisting about the longitudinal axis and thus relieves itself from the stiffer major axis in-
plane bending. In other words, in-plane loading leads to buckling failure in the less stiff
direction. The lateral displacement and twisting, which occur during this global buckling
mode, can be explained. The compression flange of the beam segment is like a column, and
thus is prone to buckling about the minor principal (weaker) axis, leading to lateral
deflections. Twisting of the beam segment occurs because the compression flange displaces
laterally while the tension flange tends to resist the lateral displacement. The lateral torsional
buckling depends mainly on the cross-section geometry, unbraced length and end restraints.
For a simply supported beam made of constant cross-sections such as I- and channel sections
subjected to uniform bending (constant bending moment), the elastic lateral torsional
buckling moment M
o
is given by the following well known formula.
M
o
= )] ( )[ (
2
2
2
2
e
w
e
y
l
EI
GJ
l
EI
+ (4.10)
where
l
e
= the distance between the restraints preventing lateral deflection and twisting (but
allows free rotation in plan), known as effective length.
EI
y
= the flexural rigidity about the minor axis
GJ = the uniform torsional rigidity
EI
w
= the warping torsional rigidity
E, G = Elastic and Shear moduli
Torsion constant J = bt
3
/3 for open sections
4-12
Warping constant I
w
= I
y
d
f
2
/4 for an I-section where d
f
is clear web depth
I
w
=
48
2 3
w f
f
b t b
(8 -
x
w f f
I
b t b
2
3
) for a channel section
I
w
= 0 for an angle section, a tee-section, or a narrow rectangular section
The lateral torsional buckling involves essentially two types of deformations, lateral
deflection of compression flange through minor axis bending and twisting of the beam about
the longitudinal axis. This is reflected by the buckling formula, which therefore includes the
flexural rigidity about the minor axis EI
y
and the two types of torsional rigidities GJ and EI
w
.
The commonly used sections (UBs, typical I-sections and channel sections) are open sections
(easier to connect to other members) with a high I
x
to I
y
ratio and have narrow flanges (to
eliminate local buckling). This means these sections have comparatively low values of these
rigidities (EI
y
, GJ and EI
w
), and are therefore susceptible to lateral torsional buckling. They
need adequate lateral/torsional restraints at the supports and at points of concentrated loads.
The Universal Columns (UCs) have a higher resistance to lateral torsional buckling because
of wider flanges, however, their bending capacity about the major axis is lower than UB
sections. Despite this, many types of construction allow effective bracing/restraints to be
included so that these efficient beam sections such as UBs are commonly used.
On the other hand, the sections with larger values for these rigidities will have greater lateral
torsional buckling moment capacity. For example, closed sections such as RHS, SHS and
CHS, square and round bars are not susceptible to lateral buckling and require far less
bracing. Also, the beam segments bent about their weak (minor principal) axis do not fail by
lateral torsional buckling provided that the loads are not applied too high above the shear
centre. In these cases, the beam segments can be designed based on their section moment
capacity M
s
. Similarly if the distance l is decreased by providing intermediate lateral
restraints, the beam segments will not buckle laterally, and as stated earlier, it can be assumed
fully braced and designed based on its section moment capacity M
s
.
4.4.3.3 Effective length
The elastic flexural torsional buckling moment M
o
of a beam segment is affected by the
effects of cross-sectional distortion, load height and rotational end restraints. It also depends
on the restraint conditions of the ends of the segment. The AS 4100 takes these effects into
account through the use of an effective length l
e
instead of l as defined next.
l
e
= k
t
k
l
k
r
l (4.11)
where k
t
= twist restraint factor
k
l
= load height factor
k
r
= lateral rotation restraint factor
4-13
Restraint Conditions at the Segment End Cross-sections
The AS 4100 classifies the restraint conditions at a cross-section as either Fully restrained (F),
Partially restrained (P), Laterally restrained (L) or Unrestrained (U). The two important
deformations that affect lateral torsional buckling are lateral displacement of critical flange
and twist about the longitudinal axis. Accordingly, the AS 4100 defines the Fully restrained
cross-sections (F) to be those which are effectively prevented from deflecting laterally and
twisting. The level of torsional restraint required at the cross-section can be reduced if the
lateral restraint acts on the critical flange. On the other hand, if the lateral restraint is not at
the critical flange, a full torsional restraint will be required for a Fully restrained condition at
the cross-section.
The partially restrained cross-sections (P) are effectively prevented from deflecting laterally,
but only partially prevented from twisting. The laterally restrained cross-sections (L) are
effectively restrained from deflecting laterally at the critical flange, but are unrestrained
against twisting. The unrestrained cross-sections (U) are those, which have no lateral or twist
restraints. The cross-sections, which are not effectively prevented from deflecting laterally,
are also considered as Unrestrained even if they have full twist restraint. Similarly if the
cross-sections are effectively prevented from deflecting laterally only at points away from the
critical flange, they are also considered unrestrained if they do not have partial or full twist
restraint. Figures 5.4.2.1, 5.4.2.2, and 5.4.2.4 of AS 4100 give examples of fully restrained,
partially restrained and laterally restrained cross-sections. An AISC publication entitled
Design of unbraced beams by Trahair et al. (1993) uses 38 real connections to demonstrate
the classification into the various restraint types. This enables the designer to choose an
appropriate restraint for the connection under consideration.
In the design of a beam, the cross-sections have to be classified as fully (F), partially (P) or
laterally (L) restrained or unrestrained (U), based on which the beam is divided into segments
or sub-segments. A segment is a length between fully or partially restrained cross-sections
(FF, FP, PP) whereas a sub-segment has one end laterally restrained (L) (FL, PL, LL). In the
design of beams there is no need to separate the two types of segments.
Twist restraint factor
Table 4.2 Twist Restraint Factor k
t
Restraint arrangement Factor k
t
FF, FL, LL, FU 1.0
FP, PL, PU
w
3
w
f 1
n
] )
t 2
t
)(
l
d
[(
1+
PP
w
3
w
f 1
n
] )
t 2
t
)(
l
d
( 2 [
1+
Notes: d
1
= clear depth of web
n
w
= number of webs
t
f
= thickness of critical flange t
w
= thickness of web
l = segment length
4-14
This factor takes into the effects of cross-sectional distortion that occurs in beams with deep
thin webs (see Figure 4.9). The cross-sectional distortion increases the twist rotation and thus
reduces the buckling capacity. It depends on the web flexibility. Table 4.2 gives the twist
restraint factor k
t
as a function of the cross-section geometry, length and restraint conditions
at segment ends. For most of the standard sections and connection details, this factor is closer
to unity. Note that it is also unity when both ends are fully or laterally restrained.
Before
buckling
After
buckling
Figure 4.9 Distortion of Beams Figure 4.10 Loads Acting on the Top Flange
Load height factor k
l
The loads can be transferred to a beam via its top flange (ex. loading/secondary beam located
on top flange), the middle (ex. secondary beam connected to the web) or its bottom flange
(ex. crane girder). The loads acting at the top flange will move with it when it buckles as
shown in Figure 4.10 This creates additional torques and twist rotations, which reduce the
buckling capacity. The AS 4100 allows for this effect through the use of a load height factor
k
l
. This factor is equal to one when the load acts at the shear centre or below. Table 4.3 gives
the load height factor k
l
as a function of the load height position and restraint conditions at
segment ends. It is also equal to one when the load acts at the segment end of type F, P or L.
The factor can be as high as 2 for segments of the type FU, PU (one end free) as shown in the
table. Therefore, this factor needs to be carefully determined.
Table 4.3 Load Height Factor k
l
Load height position Longitudinal
position of the load
Restraint arrangement
Shear Centre Top Flange
FF, FP, FL, PP, PL, LL 1.0 1.4 Within segment
FU, PU 1.0 2.0
FF, FP, FL, PP, PL, LL 1.0 1.0 At segment end
FU, PU 1.0 2.0
Lateral rotation restraint factor k
r
This factor takes into the improvement to lateral buckling due to the lateral rotation restraint
at the segment ends. This is the restraint to the beams lateral rotation (not the in-plane
rotation) when the beam is loaded with vertical transverse loads. The AS 4100 allows for this
4-15
effect through the use of a lateral rotation restraint factor k
r
. Table 4.4 gives the lateral
rotation restraint factor k
r
as a function of the restraint conditions at segment ends. The AISC
publication on the Design of unbraced beams by Trahair et al. (1993) recommends the use of
k
r
= 1 because lateral rotation restraints are not dependable.
Table 4.4 Lateral Rotation Restraint Factor k
r
Restraint arrangement Ends with lateral
rotation restraints
Factor k
r
FU, PU Any 1.0
FF, FP, FL, PP, PL, LL None 1.0
FF, FP, PP One 0.85
FF, FP, PP Both 0.70
4.4.3.4 Member Capacity
The elastic flexural torsional buckling moment M
o
given in Section 4.4.3.2 is not the ultimate
strength of real beams. The real beams have initial geometric imperfections and residual
stresses, and therefore have reduced capacity as shown in Figure 4.11. As seen in the figure,
the ultimate strength of very slender beams (large l
e
) is approximately equal to the elastic
flexural torsional buckling capacity whereas the ultimate strength of short beams is limited by
their section capacity M
s
. Other beams have an ultimate strength less than both M
o
and M
s
and this strength is reduced depending on the imperfections (initial bow and twist, residual
stresses and other).
0 0.5 1.0 1.5 2.0 2.5
0.5
1.0
Elastic
Buckling
Curve
Slenderness
N
o
n
d
i
m
e
n
s
i
o
n
a
l
c
a
p
a
c
i
t
y
M
b
/
M
s
Figure 4.11 Moment Capacity of Real Beams
The AS 4100 therefore recommends the following equation to calculate the member capacity
of a beam segment.
M
b
=
m
s
M
s
M
s
(4.12)
4-16
where
s
= a slenderness reduction factor that relates the elastic buckling moment to member
capacity = 0.6 [ ) ( ] 3 ) [(
2
o
s
o
s
M
M
M
M
+ ]
m
= a moment modification factor
M
s
= the nominal section moment capacity
The elastic flexural torsional buckling moment M
o
and the member capacity
s
M
s
are for
beam segments subject to uniform bending. However, the real beams usually have transverse
loads and are thus subjected to varying bending moment distribution. Therefore a moment
modification factor
m
is added to the member capacity equation. From a buckling point of
view, the worst case is when a beam is subjected to uniform bending. Therefore in most cases
the
m
factor is greater than 1. The AS 4100 states that the
m
factor can be calculated as one
of the following.
Conservatively taken as 1.0
From Table 5.6.1 of AS 4600
Using
m
=
2 *
4
2 *
3
2 *
2
*
) ( ) ( ) [(
7 . 1
M M M
M
m
+ +
2.5 (4.13)
where M
m
* = maximum design bending moment in the segment
M
2
*, M
4
* = design bending moments at the quarter points of the segment
M
3
* = design bending moment at the midpoint of the segment
The following gives the
m
values for the most common bending moment distributions. It
must be noted that the
m
value is for the beam segment being designed, ie. the segment
between restrained cross-sections. Further, the
m
values are quite large with the maximum
being 3.5. This implies that the member capacity is 3.5 times that of uniform bending. Hence,
the determination of
m
values must be done carefully. Note that AISC design capacity tables
assume
m
= 1. So the AISC moment capacity must be multiplied by an appropriate
m
value.
Both ends fully or partially restrained
1. Uniform moment
m
= 1
2. Central load
m
= 1.35
3. Moment at one end
m
= 1.75
Fig. 4.12 Moment Modification factors
m
(a) Both ends fully or partially restrained
4-17
4. Linear moment variation Calculate end moment ratio
m
This figure shows positive
m
m
= 1.75+1.05
m
+0.3
m
2
for -1
m
0.6
m
= 2.5 for 0.6<
m
1
5. Uniformly distributed load
m
= 1.13
6. Fixed ended beam
7. Continuous beam segments with uniformly distributed loading
End span Use Table 5.6.1
Calculate
m
first
using your moments
Middle spans
8. Continuous beam segments with point loading
End span Use Table 5.6.1
Calculate
m
first
using your moments
Middle spans
Note:
m
is the ratio of smaller to larger end moment in the segment, ie. between -1 and 1
Fig. 4.12 Moment Modification factors
m
(a) Both ends fully or partially restrained
m
= 2.42
4-18
The design rules stated earlier are for the following: segments fully or partially restrained at
both ends, Open sections with equal flanges, and Segments with constant cross-section. The
design method for segments with varying cross-section is given in Clause 5.6.1.1 (b) of AS
4600. Clauses 5.6.1.2 of AS 4600 gives the design method for I-sections with unequal
flanges. For angle and hollow sections, the same method is used but with I
w
= 0 according to
Clauses 5.6.1.3 and 5.6.1.4, respectively.
For segments unrestrained at one end, the same method can be used provided the other end
is fully or partially restrained and laterally continuous or restrained against lateral rotation. In
this case, appropriate
m
values given in Table 5.6.2 of AS 4600 have to be used. The
following are the
m
values for the most common bending moment distributions.
Unrestrained at one end and the other end fully or partially restrained
1. Uniform moment
m
= 0.25
2. Point load at the end
m
= 1.25
3. Uniformly distributed load
m
= 2.25
Figure 4.12 Moment Modification factors
m
(b) Unrestrained at one end and the
other end fully or partially restrained
The type and arrangement of lateral restraints are very important as they can considerably
increase the member capacity. Lateral/torsional restraints within the span will be very
beneficial. For a lateral restraint (bracing) to be effective, it should provide resistance to
lateral displacement and twist to the critical flange. The lateral restraint/bracing must have
adequate stiffness to restrain the braced point without moving, but also adequate strength to
withstand any forces transferred to it by the main beam. In designing the bracing, it is
assumed to carry 2.5% of the maximum compression force in the flange.
A beam without intermediate lateral restraints is regarded as a single-segment beam, provided
that the sections at the supports are adequately restrained against lateral displacement and
twisting. The addition of one restraint within the span produces a two-segment beam, ie.
buckling now takes place between restraints. More than two lateral restraints can also be
4-19
used. This divides the beam into segments and thus reduces its effective length (increases M
o
and thus M
b
)
Uneconomical designs results when slender sections and largely unbraced beams are used.
Slender sections use only part of the cross-section and thus steel is wasted. Attempts must be
made to use other sections if possible. Excessive lateral slenderness is measured by
s.
If this
value is less than 0.7, the design must be considered uneconomical. If possible, the beam
should be redesigned by introducing more lateral restraints or suitable bracing systems
(shorter segment length) or by changing the section with increased lateral buckling capacity
(SHS, CHS, RHS).
In general, there are two types of beam bracing systems, lateral and torsional. Effective beam
bracing systems must prevent relative displacement between top and bottom flanges (ie.
prevents twist). Lateral bracing (restraining members attached to the compression flange) and
torsional bracing (cross-frame or diaphragms between adjacent beams at intermediate
locations or continuous bracing by floor systems, metal decks and slabs) can provide this.
Lateral bracing systems are most effective if they are connected to the critical flange. Some
bracing systems such as concrete slab attached to the top flange via shear studs can control
both lateral displacement and twist. Research has shown such combined lateral and torsional
bracing is more effective, particularly for beams subject to uniform moment. In a common
example of beams linked together along the span, the beams cannot buckle laterally unless all
of them buckle. Therefore buckling of an individual beam can occur only between the cross-
members. If two adjacent members are connected by a properly designed cross-frame or
diaphragm at intermediate points, those points can be considered as effectively braced (SSRC,
1998). Both beams can move laterally in the middle, but since they will move equal amounts
without any twist, the beams can be considered braced at these points. Some designers
assume the point of contraflexure to be a braced point, however, research has shown this to be
incorrect. Figure 4.13 shows some of the bracing systems that are used in steel construction.
Figure 4.13 Bracing Systems
4-20
4.4.3.5 Example Problems on Global Buckling of Beams
Example Problem No.1
Figure 4.14 shows the roof structure of a service station building. Determine the size of a
suitable UB section for the main beams B if the wind uplift pressure on the roof is 2.5 kPa.
Beam
B
2m
Column A
Elevation
1.5 m
Plan View
Figure 4.14. Service Station Building for Example Problem 1
11 m 2 m
2 m
11 m
2 m
Column A
Purlins
Main Beams B
1.5 m
8 m
Metal sheeting Purlins
4-21
Table 4.5 Reference Buckling Moment M
o
(kNm)
Effective Length
Section 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0
610UB125 92148 23194 10424 5953 3882 2756 2076 1634 1329 1110 947 823 725 646 529 447 387 341 304 275 251 231
610UB113 79981 20111 9023 5142 3344 2367 1777 1393 1130 940 800 692 608 540 440 370 319 280 249 225 205 188
610UB101 68088 17102 7660 4355 2825 1993 1491 1165 941 780 661 570 498 441 357 299 256 223 198 178 162 148
530UB92.4 48691 12262 5515 3153 2059 1464 1105 871 710 594 507 441 389 348 285 242 209 185 165 150 137 126
530UB82.0 40906 10287 4617 2632 1713 1213 911 715 580 483 411 356 313 278 227 191 165 145 129 116 106 97
460UB82.1 32770 8286 3751 2163 1426 1025 782 624 514 435 375 330 293 264 220 189 165 147 132 120 111 102
460UB74.6 29137 7355 3321 1908 1254 897 682 541 444 374 322 282 250 224 186 159 138 123 110 100 92 85
460UB67.1 25367 6393 2879 1648 1078 768 581 459 375 314 269 234 207 185 153 130 112 99 89 81 74 68
410UB59.7 18837 4760 2153 1240 816 586 446 355 292 247 213 187 166 149 124 106 93 83 74 68 62 57
410UB53.7 15954 4024 1815 1041 682 487 369 292 239 201 173 151 134 120 99 84 73 65 58 53 49 45
360UB56.7 15121 3838 1748 1015 675 490 377 303 252 215 187 165 148 134 112 97 85 76 69 63 58 54
360UB50.7 13093 3315 1504 869 575 414 317 254 210 178 154 135 121 109 91 78 69 61 55 50 46 43
360UB44.7 10977 2772 1253 720 474 339 258 205 169 142 122 107 95 86 71 61 53 47 42 38 35 33
310UB46.2 10582 2692 1230 718 480 350 270 218 182 156 136 121 108 98 83 72 63 57 51 47 43 40
310UB40.4 8913 2260 1028 596 395 286 220 176 146 124 108 95 85 77 65 56 49 44 39 36 33 31
310UB32.0 5083 1289 586 339 225 163 125 100 83 71 61 54 48 44 37 31 28 25 22 20 19 17
250UB37.3 5534 1421 659 391 266 197 155 127 107 93 82 73 66 61 52 45 40 36 33 30 28 26
250UB31.4 4315 1100 505 296 199 146 113 92 77 66 58 51 46 42 36 31 27 24 22 20 19 17
250UB25.7 2438 626 290 172 117 87 68 56 47 41 36 32 29 27 23 20 18 16 14 13 12 11
200UB29.8 3050 793 374 227 157 119 95 79 67 59 52 47 43 39 34 30 26 24 22 20 18 17
200UB25.4 2386 615 287 171 117 88 69 57 48 42 37 33 30 28 24 21 18 17 15 14 13 12
200UB22.3 2130 546 252 149 101 75 59 48 41 35 31 28 25 23 19 17 15 13 12 11 10 10
200UB18.2 876 231 111 68 48 37 30 25 21 19 17 15 14 13 11 10 9 8 7 7 6 6
180UB22.2 852 239 123 81 60 48 39 34 30 26 24 22 20 18 16 14 13 12 11 10 9 8
180UB18.1 664 181 90 58 42 33 27 23 20 18 16 15 13 12 11 9 8 8 7 6 6 6
180UB16.1 574 154 76 48 34 27 22 18 16 14 13 12 11 10 8 7 7 6 6 5 5 4
150UB18.0 418 125 69 47 36 29 24 21 18 16 15 14 13 12 10 9 8 7 7 6 6 5
150UB14.0 295 84 44 29 22 17 15 13 11 10 9 8 7 7 6 5 5 4 4 4 3 3
4-22
Example Problem No. 2
Design the beam ABCD shown in Figure 2. The loads shown include load factors. The
connection and support conditions at A, B and C are as per the AISC publication (Types 1, 11
and 8, respectively).
Type 11
A 3 m B 3 m C 3 m D
Type 1 Type 8
Figure 4.16. Beam ABCD for Example Problem 2
4.5 Serviceability Design of a Beam
The beams undergo transverse deformations, and must be checked against acceptable
deflection limits. Otherwise, cracking in walls, ceilings and openings located under the
beams may occur. Deflections under serviceability design loads can be calculated using
available theoretical formulae or computer analyses. Appendix B of AS 4100 gives
appropriate deflection limits for beams. The total vertical deflection limit for beams is
span/250, but span/125 for cantilever beams. Table 1.1 in this set of notes presents the
recommended values of deflection limits.
References:
Trahair, N.S., Hogan, T.J. and Syam, A.A. Design of Unbraced Beams, Steel
Construction, J. of Australian Institute of Steel Construction, Vol.27, No.1, Feb 1993.
Structural Stability Research Council (SSRC), Guide to Stability Design Criteria for
Metal Structures, Ed. By T.V. Galambos, 5
th
Edition, John Wiley & Sons, 1998
400 kN
100 kN
Bending moment
4-23
TUTORIAL PROBLEMS ON BEAMS
Questions on Local Buckling and yielding
Question 1
Using the AS4100 limits, which plate elements will buckle locally in the following sections?
Categorise them into Compact, Non-compact and Slender sections. Assume f
y
= 250 MPa
and t = 8 mm. Assume the given centreline dimensions in your calculations.
Figure 1. Steel Beams
Question 2
Determine the Z
x
, Z
y,
S
x,
, S
y
, the shape factors, yielding moment M
yield
and plastic moment M
p
about the major and minor principal axes for the I-section shown in Figure 2. Assume Grade
250 steel (f
y
= 250 MPa) and the beam is fully restrained. t
f
= 25 mm t
w
= 16 mm
(Ans: 1091 x 10
4
mm
4
, 633 x 10
3
mm
4
; 1289 x 10
4
mm
3
, 1017 x 10
3
mm
3
, 2727, 3222
kNm; 158, 254 kNm)
60 60
60 60
270
LW
60 60
60 60
960 LW
120 120
120 120
1000 HW
250
720
HW
400
200
200
LW
4-24
275 mm
Figure 2. I-section Beam
Question 3
Determine the maximum design moment M* of a lightly welded plate girder of Grade 250
steel, which has full lateral restraint. t
f
= 25 mm t
w
= 10 mm (Ans. 2908
kNm)
300 mm
Figure 3. Lightly Welded Plate Girder
Questions on Global Buckling and yielding
Question 4
Determine the maximum design uniformly distributed load a 460UB67 of Grade 300 steel can
carry. The beam is simply supported over a span of 5 m, and is fully restrained at the supports
against lateral deflection and twist rotation, but unrestrained against lateral rotation. Assume
that the load is applied to the top flange. (Ans. 48.6 kNm)
1170 mm
1500 mm
4-25
Question 5
A simply supported beam with a span of 7 m has a nominal central concentrated live load of
55 kN on the top flange. The beam is restrained against lateral displacement and twist only at
the ends, and is free to rotate in plan. Design a suitable UB section. (Ans. 460UB82.1)
Question 6
Figure 4 shows the layout of a temporary bridge of 10 m span, used in a construction site. It is
constructed using a number of 530UB82 steel beams spaced at 2 m with a 100 mm height
timber deck on top. During construction, this bridge will be subjected to a heavy live load of
5 kPa of length 5 m as shown in the figure. The density of hardwood timber used can be taken
as 10 kN/m
3
.
a) Determine the adequacy of the 530UB82 to carry the load combination of dead load and
live load if the timber deck does NOT offer any lateral restraint due to inadequate
connections between the deck and beams. Your calculations need to include design checks
for bending capacity. (Ans. 94.7 < 182.6 kNm Inadequate)
b) From the above calculations, how will the beam fail first if tested to failure?
Figure 4. Bridge Layout