LMP 91200

LMP91200
www.ti.com
SNAS571C JANUARY 2012 REVISED MARCH 2013
LMP91200 Configurable AFE for Low-Power Chemical Sensing Applications

Check for Samples: LMP91200
FEATURES
DESCRIPTION
The LMP91200 is a configurable sensor AFE for use

in low power analytical sensing applications. The
LMP91200 is designed for 2-electrode sensors. This
device provides all of the functionality needed to
detect changes based on a delta voltage at the
sensor. Optimized for low-power applications, the
LMP91200 works over a voltage range of 1.8V to
5.5V. With its extremely low input bias current it is
optimized for use with pH sensors. Also in absence of
supply voltage the very low input bias current reduces
degradation of the pH probe when connected to the
LMP91200. The Common Mode Output pin (VOCM)
provides a common mode offset, which can be
programmed to different values to accommodate pH
sensor output ranges. For applications requiring a
high impedance common mode this option is also
available. Two guard pins provide support for high
parasitic impedance wiring. Support for an external
Pt1000, Pt100, or similar temperature sensor is
integrated in the LMP91200. The control of this
feature is available through the SPI interface.
Additionally, a user controlled sensor diagnostic test
is available. This function tests the sensor for proper
connection and functionality. Depending on the
configuration, total current consumption for the device
is 50A while measuring pH. Available in a 16-pin
TSSOP package, the LMP91200 operates from -40C
to +125C.
Programmable Output Current in Temperature

Measurement
Programmable Output Common Mode Voltage
Active Guarding
On Board Sensor Test
Supported by Webench Sensor AFE Designer
Supported by Webench Sensor Designer Tools
APPLICATIONS
pH Sensor Platforms
KEY SPECIFICATIONS
Unless otherwise noted, typical values at
TA = 25C, VS=(VDD-GND) = 3.3V
pH Buffer Input bias current (0<VINP <3.3V)

max @ 25C: 125 fA
max @ 85C: 445 fA
pH Buffer Input bias current (-500mV<VINP-VCM
<500mV), VS=(VDD-GND)=0V
max @ 25C: 600 fA
max @ 85C: 6.5 pA
pH Buffer Input offset voltage: 200 V
pH Buffer Input offset voltage drift: 2.5 V/C
Supply current (pH mode): 50 A
Supply voltage: 1.8 V to 5.5 V
Operating temperature range: -40C to 125C
Package: 16-Pin TSSOP
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright 20122013, Texas Instruments Incorporated
LMP91200
www.ti.com
Typical Application
VDD
LMP91200
pH Meter
RANGE
SETTING
CSB
SCLK
SDI
SPI
PGA
CONTROLLER
CAL
VOUT
R_REF
RTD
VOUT
MUX
2-wire RTD
GUARD1
INP
pH
BUFFER
VOCM
VCM
MUX
GUARD2
VREF
VCM
BUFFER
VCM
SDO_DIAG
GND
pH ELECTRODE
VCMHI
Connection Diagram
16-Pin TSSOP
VDD
16
SDI
SCLK
CAL
15
RTD
14
CSB
GUARD1
13
SDO_DIAG
INP
12
VOUT
GUARD2
11
VOCM
VCMHI
10
GND
VCM
LMP91200
VREF
Figure 1. Top View
Submit Documentation Feedback
Product Folder Links: LMP91200
LMP91200
www.ti.com
PIN DESCRIPTIONS
Pin
Name
Description
VDD
Positive Power Supply
CAL
Connect an external precision resistor here for purpose of temperature

measurement calibration
RTD
Pt100/Pt1000 input / internal current source output
GUARD1
Active guard pin
INP
Non-inverting analog input of pH buffer
GUARD2
Active guard pin
VCMHI
High Impedance Programmable Common Mode output
VCM
Buffered Programmable Common Mode output
VREF
Voltage reference input
10
GND
Analog ground
11
VOCM
Output common mode voltage
12
VOUT
Analog Output
13
SDO_DIAG
Serial Data Out /Diagnostic enable
14
CSB
Chip select, low active.
15
SCLK
Serial Clock
16
SDI
Serial Data In
Absolute Maximum Ratings (1) (2) (3)

Human Body Model
ESD Tolerance
(4)
2000V
Machine Model
150V
Charge Device Model

Supply Voltage (VS = VDD-GND)
1000V
-0.3V to 6.0V
Voltage between any two pins
-0.3V to VDD+0.3V
Current out at any pin
5mA
Storage Temperature Range
-65C to 150C
Junction Temperature (5)

(1)
(2)
(3)
(4)
(5)
+150C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not specified. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
For soldering specifications see product folder at www.ti.com and SNOA549
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
The maximum power dissipation is a function of TJ(MAX), JA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/JA. All numbers apply for packages soldered directly onto a PC Board.
Operating Ratings (1)

Supply Voltage (VS=VDD-GND)
1.8V to 5.5V
Temperature Range
Package Thermal Resistance (JA (2))
(1)
(2)
-40C to 125C
16-Pin TSSOP
31C/W
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not specified. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
The maximum power dissipation is a function of TJ(MAX), JA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/JA. All numbers apply for packages soldered directly onto a PC Board.
LMP91200
www.ti.com
Electrical Characteristics (1) (2) (3)

Unless otherwise specified, all limits specified for TA = 25C. VS=(VDD-GND)=3.3V. VREF=3.3V. Boldface limits apply at the
temperature extremes.
Symbol
Parameter
Typ (5)
Max (4)
pH measurement mode
50
54
59
Temperature measurement mode,

ICS=100uA
300
325
330

ICS=200uA
400
432
437

ICS=1000uA
350
364
372

ICS=2000uA
470
477
477
Condition
Min (4)
Units
Power supply
Supply Current (6) (7)
Is
pH Buffer
AolpH
INP=1.65V, 300mV = VOUT = VDD300mV
Open loop Gain
VospH
Input Voltage Offset
Input offset voltage drift (8) (9)
VOSpH_drift
Long term VOSpH drift (10)
IbpH
Input bias current at INP
200
350
INP=7/8VREF
-200
-350
200
350
INP=1/8VREF
-2.5
2.5
INP=7/8VREF
-2.5
2.5
150
fA
0V<INP<3.3V, 85C
-445
445
fA
0V<INP<3.3V, 125C
-1.5
1.5
pA
-500mV<(INP-VCM)<500mV, VS=0V.
-600
600
fA
-500mV<(INP-VCM)<500mV,
85C, VS=0V.
-6.5
6.5
pA
-500mV<(INP-VCM)<500mV,
125C, VS=0V.
-100
100
pA
CMRRpH
DC_Common mode rejection

ratio
1/8VREF<INP<7/8VREF
80
1.8V<VDD<5V
INP=1/8VREF
80
1.8V<VDD<5V
INP=7/8VREF
80
Input referred noise (low

frequency) (9)
V
125
CL=10pF, RL=1Mohm
En_RMSpH
uV/C
-125
Gain Bandwidth Product (9)
DC_Power supply rejection ratio
0V<INP<3.3V
GBWPpH
PSRRpH
dB
-200
-350
500 hours OPL
(9)
120
INP=1/8VREF
(6)
TcVospH
90
Integrated 0.1Hz to 10Hz
220
KHz
dB
dB
2.6
VPP
(1)
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ >TA.
(2) Positive current corresponds to current flowing into the device.
(3) The voltage on any pin should not exceed 6V relative to any other pins.
(4) Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlations using the
Statistical Quality Control (SQC) method.
(5) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
(6) Boldface limits are production tested at 125C. Limits are specified through correlations using the Statistical Quality Control (SQC)
method.
(7) Excluding all currents which flows out from the device.
(8) Offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change.
(9) This parameter is specified by design and/or characterization and is not tested in production.
(10) Offset voltage long term drift is determined by dividing the change in VOS at time extremes of OPL procedure by the length of the OPL
procedure. OPL procedure: 500 hours at 150C are equivalent to about 15 years.
4
LMP91200
www.ti.com
Electrical Characteristics(1)(2)(3) (continued)

Symbol
Parameter
Condition
enpH
Input referred noise (high

frequency) (9)
IscpH
Output short circuit current (11)
Min (4)
f=1kHz
Typ (5)
Max (4)
Units
90
nV/Hz
Sourcing, Vout to GND, INP=1.65V
10
13
mA
Sinking, Vout to VDD, INP=1.65V
12
mA
VCM Buffer
VCMHI_acc
VCMHI accuracy
Tc_VCMHI
VCMHI temperature
coefficient (9) (12)
-1.6
VCMHI_acc_V
VCMHI_acc vs. VREF (9) (13)
REF
RoutVCMHI
AolVCM
VosVCM
VCMHI Output Impedance
(9)
(VCM-VCMHI)
-18
-5
V/C
1.8V<VREF<5.0V
-500
-100
300
V/V
VCMHI=1/2 VREF
90
120
dB
-200
-350
200
350
VCMHI=7/8 VREF
-200
-350
200
350
-2.5
2.5
-2.5
2.5
Input offset voltage drif ot (VCM- VCMHI=1/8 VREF

VCMHI) (8) (9)
VCMHI=7/8 VREF
ZoutVCM
Output Impedance (9)
f=1KHz
250
VCMHI=1/8 VREF
(6)
TcVosVCM
PSRRVCM
mV
-40C<TA<125C
VCMHI=1/2 VREF,
300mV<VCM<VDD-300mV
Open loop Gain (6)
1.6
V/C
1.8V<VDD<5V,
VCMHI=1/8VREF
80
1.8V<VDD<5V,
VCMHI=7/8VREF
80
dB
En_RMSVCM

frequency) (9)
2.6
VPP
enVCM

frequency) (14)
f=1KHz
90
nV/Hz
IscVCM
Output short circuit current
(15)
Sourcing, Vout to GND

VCMHI=1/2VREF
10
16
Sinking, Vout to VDD

VCMHI=1/2VREF
12
mA
Current Source
100
200
1000
2000
33
nAPP
f=1KHz
120
pA/Hz
ICS
Current Source ICAL, IRTD
Programmable current
In_RMSCS

frequency) (14)
inCS

frequency) (14)
TcICS
Current Source drift (14) (16)
-200
35
200
ppm/C
I_accCS
Current Source accuracy
-2.5
2.5
(11) The short circuit test is a momentary open loop test.

(12) VCMHI voltage average drift is determined by dividing the change in VCMHI at the temperature extremes by the total temperature
change.
(13) VCMHI_acc vs. VREF is determined by dividing the change in VCMHI_acc at the VREF extremes by the total VREF change.
(16) Current source drift is determined by dividing the change in ICS at the temperature extremes by the total temperature change.
LMP91200
www.ti.com
Electrical Characteristics(1)(2)(3) (continued)

Symbol
Parameter
Min (4)
Condition
Typ (5)
Max (4)
Units
275
480
2.5
uV/C
PGA
VosPGA
Input Voltage Offset (17)

(18) (19)
+IN_PGA (Internal node) = 500mV
-275
-480
TcVosPGA
Input offset voltage drift
-2.5
AolPGA
Open loop Gain
90
AvPGA
Gain
Programmable gain
Av_accPGA
Gain accuracy
En_RMSPGA

frequency) (18)
2.6
VPP
enPGA

frequency) (18)
f=1KHz
90
nV/Hz
PSRRPGA
1.8V<VDD<5V,
80
Sourcing, Vout to GND

10
16
Sinking, Vout to VDD

12
IscPGA
Output short circuit current
120
dB
5
10
V/V
-1.3
(20)
1.3
dB
mA
Reference Input
RinVREF
Input impedance (18)
500
(17) Boldface limits are production tested at 125C. Limits are specified through correlations using the Statistical Quality Control (SQC)
method.
(19) Offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change.
Electrical Characteristics (Serial Interface) (1)

Unless otherwise specified. All limits specified for TA=25C, VS=(VDD-GND)=3.3V.
Symbol
(1)
(2)
(3)
(4)
6
Parameter
VIL
Logic Low Threshold
VIH
Logic High Threshold (SDO pin)
Condition
Min (2)
Typ (3)
Max (2)
Units
0.3XVDD
0.7XVDD
ISDO=100A
0.2
ISDO=2mA
0.4
VOL
Output Logic LOW Threshold

(SDO pin)
VOH
Output Logic High Threshold
t1
High Period, SCLK
100
ns
t2
Low Period, SCLK
100
ns
t3
Set Up Time, CSB to SCLK
50
ns
t4
Set Up Time, SDI to SCLK
30
ns
ISDO=100A
VDD-0.2
ISDO=2mA
VDD-04
See (4)
V
V
t5
Hold Time,S CLK to SDI
10
ns
t6
Hold Time,SCLK to SDO_DIAG
40
ns
t7
Hold Time, SCLK Transition to

CSB Rising Edge
50
ns
Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlations using the
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
Load for these tests is shown in the timing diagram test circuit.
LMP91200
www.ti.com
Electrical Characteristics (Serial Interface)(1) (continued)

Symbol
(5)
Parameter
Min (2)
Condition
t8
CSB Inactive
t9
Hold Time, SCLK Transition to

CSB Falling Edge
See (4)
tR/tF
SDO_DIAG Signal Rise and Fall

Times
Diagnostic disabled (4) (5)
Typ (3)
Max (2)
Units
50
ns
10
ns
30
ns
This parameter is specified by design and/or characterization and is not tested in production.
Electrical Characteristics (Diagnostic) (1)

Symbol
DIAG_tSET
DIAG_tR/DIAG_tF
DIAG_tON
Parameter
SDO_DIAG setup time
Min (2)
Condition
(4)
Typ (3)
Max (2)
Units
200
ns
Diagnostic Rise and Fall

Times (Signal at SDO_DIAG
pin, in Diagnostic Mode) (4)
30
ns
Minimum tON of the diagnostic

pulse at SDO_DIAG pin in
Diagnostic Mode (4)
100
ns
VCM_DIAGPOS
Positve Diagnostic pulse

amplitude (4)
Base pulse = VCM;

High level pulse = VCM+5%VREF
165
mV
VCM_DIAGNEG
Negative Diagnostic pulse

amplitude (4)
Base pulse = VCM;

High level pulse = VCM-5%VREF
165
mV
VCM_DIAG_acc
Diagnostics Pulse accuracy (4)
0.1
VCM_DIAGtR
Diagnostics Pulse rise time (4)
10% to 90%, C = 15pF
10
us
VCM_DIAGtF
Diagnostics Pulse fall time (4)
90% to 10%, C=15pF
10
us
(1)
(2)
(3)
(4)
Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlations using the
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
This parameter is specified by design and/or characterization and is not tested in production.
Test Circuit Diagrams
IOL
TO
SDO_DIAG
PIN
VDD/2
CL
50 pF
IOH
LMP91200
www.ti.com
TEST CIRCUIT DIAGRAMS

SCLK
t9
t1
t2
t3
t7
CSB
t4
t8
t5
D15
SDI
D0
D14
t6
OLD D15
SDO_DIAG
90%
OLD D1
10%
90%
10%
tR
OLD D0
tF
Figure 2. SERIAL INTERFACE TIMING DIAGRAM

DIAG_tSET
CSB
50%
DIAG_tON
DIAG_tF
50%
SDO_DIAG
50%
50%
90%
90%
10%
90%
10%
10%
90%
90%
10%
VCMHI
DIAG_tR
10%
VCM_DIAG_tR
VCM_DIAG_tF
T1
T2
T3
Figure 3. DIAGNOSTIC TIMING DIAGRAM
LMP91200
www.ti.com
Typical Performance Characteristics

Unless otherwise specified, TA=25C, VS=(VDD-GND)=3.3V, VREF=3.3V.
pH Buffer Input Bias Current
vs.
VINP - Device ON
100
500
Average
Average -31
Average +31
60
300
40
200
20
0
-20
-40
-60
240
0.5
1.0
1.5 2.0
INP (V)
2.5
3.0
3.5
-0.50

vs.
VINP - Device OFF
5
Average
Average -31
Average +31
3
INPUT BIAS (pA)
INPUT BIAS (fA)
0.50
Average
Average -31
Average +31
-60
-120
-180
2
1
0
-1
-2
-3
-240
-4
TA=85C
-300
0.5
1.0
1.5 2.0
INP (V)
2.5
3.0
TA=85C
-5
3.5
-0.50
-0.25
0.00
0.25
INP-VCM (V)
Figure 6.
Figure 7.

vs.
VINP - Device ON

vs.
VINP - Device OFF
80
Average
Average -31
Average +31
60
INPUT BIAS (pA)
600
INPUT BIAS (fA)
0.00
0.25
INP-VCM (V)

vs.
VINP - Device ON
400
200
0
-200
-400
0.50
Average
Average -31
Average +31
40
20
0
-20
-40
-600
-60
-800
TA=125C
-1000
0.0
-0.25
Figure 5.
60
800
TA=25C
Figure 4.
120
1000
-200
-500
180
0.0
0
-100
-400
TA=25C
-100
300
100
-300
-80
0.0
Average
Average -31
Average +31
400
INPUT BIAS (fA)
INPUT BIAS (fA)
80

vs.
VINP - Device OFF
0.5
1.0
1.5 2.0
INP (V)
2.5
3.0
TA=125C
-80
3.5
Figure 8.
-0.50
-0.25
0.00
0.25
INP-VCM (V)
0.50
Figure 9.
LMP91200
www.ti.com
Typical Performance Characteristics (continued)

vs. Temp - Device ON
500
400

vs. Temp - Device OFF
5
Average
Average -31
Average +31
3
INPUT BIAS (pA)
INPUT BIAS (fA)
300
200
100
0
-100
-200
-300
-400
2
1
-1
-4
INP=1.65V
-5
45
65
85
105
TEMPERATURE (C)
125
25
pH Buffer Input Voltage Offset
pH Buffer Input Voltage Offset
15
PERCENTAGE (%)
PERCENTAGE (%)
UNITS TESTED >5000

INP=1/8VREF
12
9
6
UNITS TESTED >5000

INP=7/8VREF
12
9
6
0
-200 -150 -100 -50 0 50 100 150 200
VOSPH( V)
Figure 12.
Figure 13.
pH Buffer TcVos
pH Buffer TcVos
35
35
UNITS
UNITS TESTED
TESTED >5000
>5000
INP=1/8VREF
INP=1/8VREF
30
PERCENTAGE (%)
PERCENTAGE (%)
125
18
-200 -150 -100 -50 0 50 100 150 200

VOSPH( V)
25
20
15
10
20
15
10
5
Figure 14.
UNITS
UNITS TESTED
TESTED >5000
>5000
INP=1/8VREF
INP=7/8VREF
25
-2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5
TCVOSPH( V/C)
10
50
75
100
TEMPERATURE (C)
Figure 11.
18
30
INP-VCM = -100mV
-2
Figure 10.
15
INP-VCM = 100mV
-3
-500
25
Average
Average -31
Average +31
-2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5
TCVOSPH( V/C)
Figure 15.
LMP91200
www.ti.com

pH Buffer DC CMRR
vs. Temperature
105
100
pH Buffer DC PSRR
vs. Temperature
110
VDD=1.8V
VDD=3.3V
VDD=5V
INP=7/8 VREF
INP=1/8VREF
PSRR (dB)
105
95
90
100
95
85
80
-50 -25
25
50
90
75 100 125
-50
-25
0
25 50 75
TEMPERATURE (C)
Figure 16.
Figure 17.
pH Buffer Time domain Voltage Noise
pH Buffer Input Offset Voltage Drift

125
INP=7/8VREF
INP=1/8VREF
INTEGRATED NOISE (500nV/DIV)
100
75
VOSPH( V)
50
25
0
-25
-50
-75
-100
-125
1
10
100
OPL TIME (h)
TIME (1s/DIV)
Figure 19.
pH Buffer CMRR
vs. VINP - lower rail
pH Buffer CMRR
vs. VINP - upper rail
120
VDD=VREF=3.3V
110
80
100
CMRR (dB)
90
70
80
50
70
40
VDD=VREF=3.3V
90
60
0.00
1k
Figure 18.
100
CMRR (dB)
100 125
60
0.08
0.16
0.24
INP (V)
0.32
0.40
Figure 20.
2.9
3.0
3.1
INP (V)
3.2
3.3
Figure 21.
11
LMP91200
www.ti.com

pH Buffer CMRR
vs. VINP - lower rail
pH Buffer CMRR
vs. VINP - upper rail
120
120
VDD=VREF=5V
VDD=VREF=5V
110
CMRR (dB)
CMRR (dB)
110
100
100
90
80
90
70
80
60
0.00
0.12
0.24
0.36
INP (V)
0.48
0.60
4.4
4.5
4.6
4.7
4.8
INP (V)
Figure 22.
Figure 23.
pH Buffer CMRR
vs. Frequency
pH Buffer PSRR
vs. Frequency
90
4.9
5.0
90
INP=1.65V
80
85
PSRR (dB)
CMRR (dB)
70
80
75
70
60
50
40
30
20
65
10
60
0
10
100
1k
10k
FREQUENCY (Hz)
100k
10
Figure 24.
VCM Buffer Input Voltage Offset
VCM Buffer Input Voltage Offset

18
UNITS TESTED >5000

VCMHI=1/8VREF
15
PERCENTAGE (%)
12
PERCENTAGE (%)
10k
Figure 25.
15
UNITS TESTED >5000

VCMHI=7/8VREF
12
9
6
3
-200 -150 -100 -50 0 50 100 150 200

VOSVCM( V)
Figure 26.
12
100
1k
FREQUENCY (Hz)
-200 -150 -100 -50 0 50 100 150 200

VOSVCM( V)
Figure 27.
LMP91200
www.ti.com

VCM Buffer TcVos
VCM Buffer TcVos
40
35
UNITS TESTED >5000
VCMHI=1/8VREF
30
25
20
15
10
20
15
10
5
-2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5
TCVOSVCM( V/C)
-2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5
TCVOSVCM( V/C)
Figure 28.
Figure 29.
VCM Buffer DC CMRR

vs. Temperature
VCM Buffer DC PSRR

vs. Temperature
110
VDD=1.8V
VDD=3.3V
VDD=5V
95
90
100
95
85
-50
VCMHI=7/8 VREF
VCMHI=1/8VREF
105
PSRR (dB)
100
CMRR (dB)
25
105
UNITS TESTED >5000

VCMHI=7/8VREF
30
PERCENTAGE (%)
PERCENTAGE (%)
35
90
-25
0
25 50 75
TEMPERATURE (C)
100 125
-50
-25
0
25 50 75
TEMPERATURE (C)
Figure 30.
Figure 31.
VCM Buffer Time domain Voltage Noise
VCM Buffer PSRR

vs. Frequency
100 125
90
VCMHI=1.65V
80
PSRR (dB)
70
60
50
40
30
20
10
10
TIME (1s/DIV)
Figure 32.
100
1k
FREQUENCY (Hz)
10k
Figure 33.
13
LMP91200
www.ti.com

VCMHI error
vs. Temp
0.25
ERROR (%)
0.20
0.15
0.30
VCMHI=1/8VREF
VCMHI=1/4VREF
VCMHI=3/8VREF
VCMHI=1/2VREF
VCMHI=5/8VREF
VCMHI=3/4VREF
VCMHI=7/8VREF
0.20
0.10
0.05
0.15
0.10
0.05
0.00
0.00
-0.05
-0.05
-0.10
-50
VCMHI=1/8VREF
VCMHI=1/4VREF
VCMHI=3/8VREF
VCMHI=1/2VREF
VCMHI=5/8VREF
VCMHI=3/4VREF
VCMHI=7/8VREF
0.25
ERROR (%)
0.30
VCMHI error
vs. Supply Voltage
-0.10
-25
0
25 50 75
TEMPERATURE (C)
100 125
1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0

SUPPLY VOLTAGE (V)
Figure 34.
Figure 35.
PGA Input Voltage Offset
PGA TcVos
15
30
UNITS TESTED >5000
+IN_PGA=500mV
24
PERCENTAGE (%)
12
PERCENTAGE (%)
UNITS TESTED >5000

+IN_PGA=500mV
27
21
18
15
12
9
6
3
-275-220-165-110 -55 0 55 110 165 220 275

VOSPGA( V)
105.0
-2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5
TCVOSPGA( V/C)
Figure 36.
Figure 37.
PGA DC PSRR
vs. Temperature
PGA Gain error

vs. Temp
0.10
+IN_PGA=500mV
PGA Gain = 5V/V

PGA Gain = 10V/V
0.08
0.06
GAIN ERROR (%)
PSRR (dB)
102.5
100.0
97.5
95.0
0.04
0.02
0.00
-0.02
-0.04
-0.06
92.5
-0.08
90.0
-50
-25
0
25 50 75 100 125
TEMPERATURE (C)
-0.10
-50
Figure 38.
14
-25
0
25 50 75
TEMPERATURE (C)
100 125
Figure 39.
LMP91200
www.ti.com

PGA PSRR
vs. Frequency
PGA Time domain Voltage Noise

90
80
+INPGA=100mV
PSRR (dB)
70
60
50
40
30
20
10
0
10
TIME (1s/DIV)
Figure 41.
Current Source (ICS=100A)
Temperature coefficient Current Source (ICS=100A)

30
UNITS TESTED >5000

IOUTCS=100 A
25
PERCENTAGE (%)
PERCENTAGE (%)
25
20
15
10
5
UNITS TESTED >5000

IOUTCS=100 A
20
15
10
5
0
98
99
100
IOUTCS( A)
101
102
-200 -150 -100 -50 0 50 100 150 200

IOUTCS(ppm/C)
Figure 42.
Figure 43. g
30
30
UNITS TESTED >5000
IOUTCS=200 A
25
PERCENTAGE (%)
PERCENTAGE (%)
10k
Figure 40.
30
25
100
1k
FREQUENCY (Hz)
20
15
10
20
15
10
196 197 198 199 200 201 202 203 204

IOUTCS( A)
Figure 44.
UNITS TESTED >5000

IOUTCS=200 A
-200 -150 -100 -50 0 50 100 150 200

IOUTCS(ppm/C)
Figure 45.
15
LMP91200
www.ti.com

25
25
20
PERCENTAGE (%)
20
PERCENTAGE (%)
UNITS TESTED >5000

IOUTCS=1000 A
UNITS TESTED >5000

IOUTCS=1000 A
15
10
15
10
980
990
1000
1010
IOUTCS( A)
1020
-200 -150 -100 -50 0 50 100 150 200

IOUTCS(ppm/C)
Figure 46.
Figure 47.

30
25
UNITS TESTED >5000
IOUTCS=2000 A
PERCENTAGE (%)
PERCENTAGE (%)
20
25
15
10
20
15
10
1960
1980
2000
2020
IOUTCS( A)
2040
Figure 49.
Current Source accuracy (I_accCS)

vs. Supply Voltage
Supply current
vs. digital input voltage
1.0
1000
0.8
900
0.6
800
EXTRA CURRENT ( A)
ERROR (%)
-200 -150 -100 -50 0 50 100 150 200

IOUTCS(ppm/C)
Figure 48.
0.4
0.2
0.0
-0.2
-0.4
-0.6
600
500
400
300
200
100
-1.0
Figure 50.
VDD=5V
700
-0.8
1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0

SUPPLY VOLTAGE (V)
16
UNITS TESTED >5000

IOUTCS=2000 A
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
DIGITAL PIN VOLTAGE (V)
Figure 51.
LMP91200
www.ti.com

Supply current (pH Mode)
vs. Temperature
50
Supply current (Temp Mode)

vs. Temperature
450
pH Mode
SUPPLY CURRENT ( A)
SUPPLY CURRENT ( A)
430
45
40
35
410
390
370
350
Temp Mode, IOUTCS=100uA

Temp Mode, IOUTCS=1mA
330
310
30
SUPPLY CURRENT ( A)
50
-25
0
25
50
75
TEMPERATURE (C)
290
-50
100 125
0
25 50 75
TEMPERATURE (C)
100 125
Figure 53.
Supply current (pH Mode)

vs. Supply Voltage
Supply current (Temp Mode)

vs. Supply Voltage
450
pH Mode
45
40
35
30
1.5
-25
Figure 52.
SUPPLY CURRENT ( A)
-50
420
390
360

330
300
270
2.0
2.5 3.0 3.5 4.0 4.5

SUPPLY VOLTAGE (V)
5.0
Figure 54.
1.5
2.0
2.5 3.0 3.5 4.0 4.5

SUPPLY VOLTAGE (V)
5.0
Figure 55.
17
LMP91200
www.ti.com
FUNCTIONAL DESCRIPTION
GENERAL INFORMATION
The LMP91200 is a configurable sensor AFE for use in low power analytical sensing applications. The
LMP91200 is designed for 2-electrode sensors. This device provides all of the functionality needed to detect
changes based on a delta voltage at the sensor. Optimized for low-power applications, the LMP91200 works
over a voltage range of 1.8V to 5.5V. With its extremely low input bias current it is optimized for use with pH
sensors. Also in absence of supply voltage the very low input bias current reduces degradation of the pH probe
when connected to the LMP91200. The Common Mode Output pin (VOCM) provides a common mode offset,
which can be programmed to different values to accommodate pH sensor output ranges. For applications
requiring a high impedance common mode this option is also available. Two guard pins provide support for high
parasitic impedance wiring. Support for an external Pt1000, Pt100, or similar temperature sensor is integrated in
the LMP91200. The control of this feature is available through the SPI interface. Additionally, a user controlled
sensor diagnostic test is available. This function tests the sensor for proper connection and functionality.
pH Buffer
The pH Buffer is a unity gain buffer with a input bias current in the range of tens fA at room. Its very low bias
current introduces a negligible error in the measurement of the pH. The ph buffer is provided with 2 guard pins
(GUARD1, GUARD2) in order to minimize the leakage of the input current and to make easy the design of a
guard ring.
Common mode selector and VCM buffer
The common mode selector allows to set 7 different values of common mode voltage (from 1/8 VREF to
7/8VREF with 1/8 VREF step) according to the applied voltage reference at VREF pin. Both buffered and
unbuffered version of the set common mode voltage are available respectively at VCM pin and VCMHI pin. A
copy of the buffered version is present at VOCM pin in case of differential measurement.
Current Source and PGA
The internal current source is programmable current generator which is able to source 4 different current values
(100A, 200A, 1mA, 2mA) in order to well stimulate Pt100 and Pt1000 thermal resistor. The selected current is
sourced from either RTD pin (pin for thermal resistor connection) or CAL pin (pin for reference resistor
connection). The voltage across either the thermal resistor or the reference resistor is amplified by the PGA
(5V/V, 10V/V) and provided at the VOUT pin when the LMP91200 is set in Temperature measurement mode.
Output Muxes
The output of the LMP91200 can be configured to support both differential and single ended ADCs. When
measuring pH the Output signal can be referred either to VCM or GND. When measuring temperature the Output
signal is referred to GND. The Output configuration is controlled through the SPI interface.
SERIAL CONTROL INTERFACE OPERATION

All the features of the LMP91200 (Mode of Operation, PGA Gain, Voltage reference, Diagnostic) are by data
stored in a programming register. Data to be written into the control register is first loaded into the LMP91200 via
the serial interface. The serial interface employs a 16-bit shift register. Data is loaded through the serial data
input, SDI. Data passing through the shift register is output through the serial data output, SDO_DIAG. The serial
clock, SCK controls the serial loading process. All sixteen data bits are required to correctly program the
LMP91200. The falling edge of CSB enables the shift register to receive data. The SCK signal must be high
during the falling and rising edge of CSB. Each data bit is clocked into the shift register on the rising edge of
SCLK. Data is transferred from the shift register to the holding register on the rising edge of CSB.
18
LMP91200
www.ti.com
Configuration Register
Bit
Name
Description
D15
MEAS_MODE
0
1
pH measurement (default)
Temp measurement
D14
I_MUX
0
1
RTD (default)
CAL
[D13:D12]
I_VALUE
00
01
10
11
D11
PGA
0
1
[D10 :D8]
VCM
011
010
001
000
100
101
110
111
D7
VOCM
0
1
VOCM (default)
GND
D6
DIAG_EN
0
1
DIAG pin disabled (default)

DIAG pin enabled
[D5 :D0]
RESERVED
RESERVED
100A (default)
200 A
1 mA
2 mA
5 V/V (default)
10 V/V
7/8Vref
3/4Vref
5/8Vref
1/2Vref (default)
1/2Vref
3/8Vref
1/4Vref
1/8 Vref
19
LMP91200
www.ti.com
Application Information
Theory of pH measurement
pH electrode measurements are made by comparing the readings in a sample with the readings in standards
whose pH has been defined (buffers). When a pH sensing electrode comes in contact with a sample, a potential
develops across the sensing membrane surface and that membrane potential varies with pH. A reference
electrode provides a second, unvarying potential to quantitatively compare the changes of the sensing
membrane potential. Nowadays pH electrodes are composed of a sensing electrode with the reference electrode
built into the same electrode body, they are called combination electrodes. A high input impedance meter serves
as the readout device and calculates the difference between the reference electrode and sensing electrode
potentials in millivolts. The millivolts are then converted to pH units according to the Nernst equation.
Electrode behavior is described by the Nernst equation:
E = Eo + (2.3 RT/nF) log aH+, where
E is the measured potential from the sensing electrode,
Eo is related to the potential of the reference electrode,
(2.3 RT/nF) is the Nernst factor,
log aH+ is the pH, (aH+ = activity of Hydrogen ions).
2.3 RT/nF, includes the Gas Law constant (R), Faradays constant (F), the temperature in degrees Kelvin (T) and
the stoichiometric number of ions involved in the process (n). For pH, where n = 1, the Nernst factor is 2.3 RT/F.
Since R and F are constants, the factor and therefore electrode behavior is dependent on temperature. The
Nernst Factor is equivalent to the electrode slope which is a measure of the electrode response to the ion being
detected. When the temperature is 25 C, the theoretical Nernst slope is 59.16 mV/pH unit.
LMP91200 in pH meter with ATC (Automatic Temperature Compensation)
The most common cause of error in pH measurements is temperature. Temperature variations can influence pH
for the following reasons:
the electrode slope will change with variations in temperature
buffer and sample pH values will change with temperature
Measurement drift can occur when the internal elements of the pH and reference electrodes are reaching thermal
equilibrium after a temperature change. When the pH electrode and temperature probe are placed into a sample
that varies significantly in temperature, the measurements can drift because the temperature response of the pH
electrode and temperature probe may not be similar and the sample may not have a uniform temperature, so the
pH electrode and temperature probe are responding to different environments.
The pH values of buffers and samples will change with variations in temperature because of their temperature
dependent chemical equilibria. The pH electrode should be calibrated with buffers that have known pH values at
different temperatures. Since pH meters are unable to correct sample pH values to a reference temperature, due
to the unique pH versus temperature relationship of each sample, the calibration and measurements should be
performed at the same temperature and sample pH values should be recorded with the sample temperature.
The LMP91200 offers in one package all the features to build a pH meter with ATC. Through the SPI Interface is
possible to switch from pH measurement mode to temperature measurement mode and collect both temperature
and potential of sensing electrode.
pH measurement
The output of a pH electrode ranges from 415 mV to 415 mV as the pH changes from 0 to 14 at 25C. The
output impedance of a pH electrode is extremely high, ranging from 10 M to 1000 M. The low input bias
current of the LMP91200 allows the voltage error produced by the input bias current and electrode resistance to
be minimal. For example, the output impedance of the pH electrode used is 10 M, if an op amp with 3 nA of
Ibias is used, the error caused due to this amplifiers input bias current and the source resistance of the pH
electrode is 30 mV! This error can be greatly reduced to 1.25V by using the LMP91200.
20
LMP91200
www.ti.com
The pH measurement with the LMP91200 is straightforward, the pH electrode needs to be connected between
VCM pin and INP pin. The voltage at VCM pin represent the internal zero of the system, so the potential of the
electrode (voltage at INP pin) will be refered to VCM voltage. The common mode voltage can be set to well fit
the input dynamic range of an external ADC connected between VOUT and VOCM when the LMP91200 is
configured with differential output. In Table 1 a typical configuration of the register of the LMP91200 with VCM
set at 1/2 of VREF and differential output.
Table 1. Configuration register: pH measurement
Bit
Name
Description
D15
MEAS_MODE
D14
I_MUX
pH measurement
[D13:D12]
I_VALUE
D11
PGA
[D10 :D8]
VCM
000 1/2 VREEF
D7
VOCM
VOCM
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
Leave these bits as they have been configured for the temperature
measurement.
Temperature measurement
The LMP91200 supports temperature measurement with RTD like Pt100 and Pt1000. According to the RTD
connected to the LMP91200 the right amount of exciting current can be programmed: 100A for Pt1000 and
1mA for Pt100, resulting in a nominal voltage drop of 100mV for both RTDs at 0C. This voltage can be
amplified, using an internal amplifier with a factor of 5 or 10 V/V. In case of high precision temperature
measurement it is possible to connect an external high accuracy resistor and implement a calibration procedure.
The exciting current sourced by the LMP91200 can be multiplexed either into the RTD or into the external
precision resistor in order to implement a 2-step or 3-step temperature measurement. The multi step temperature
measurements allows to remove uncertainty of the temperature signal path.
1-step measurement
In the one step measurement the voltage across the RTD (Pt100, Pt1000) due to the exciting current is amplified
and measured. The temperature can be calculated according to the following equation:
Temp(C) = (PtRES_calculated PtRES_nominal)/alpha
where
alpha is the thermal coefficient of the RTD (it depends on the selected Ptres)
PtRES_nominal is the value of the Ptres at 0degC
PtRES_calculated = (VOUT_PtRES/I_Pt)/PGA_GAIN
(1)
where
VOUT_PtRES is the amplified voltage across the RTD at VOUT pin (ground referred) when the LMP91200 is
configured according to Table 2
I_Pt is the value of the selected exciting current according to the RTD
PGA_GAIN is the selected gain of the PGA
(2)
Inserting Equation 2 in Equation 1 the temperature is given by the following equation:

Temp(C) = Temp(C) = ((VOUT_PtRES/I_Pt)/PGA_GAIN PtRES_nominal)/alpha
(3)
21
LMP91200
www.ti.com
Table 2. Configuration register: 1-step measurement

Bit
Name
Description
D15
MEAS_MODE
Temp measurement
D14
I_MUX
RTD
[D13:D12]
I_VALUE
00
10
D11
PGA
[D10 :D8]
VCM
Leave these bits as they have been configured for the pH

measurement.
D7
VOCM
GND
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
100A (Pt1000)
1 mA (Pt100)
10 V/V
The 1-step temperature measurement has a precision of about 3C.

2-step measurement
This method requires 2 acquisitions and a precision resistor (RREF) connected between CAL and GND pin, (the
RTD is always connected between RTD and GND pin). The first acquisitions measure the voltage across the
precision resistor in the same condition (source current and PGA gain) of the next temperature measurement in
order to remove the uncertainty on the current source value. The second acquisition measures the voltage
across the RTD (similar to the 1-step measure), in this case the formula to calculate the temperature is a little bit
more complicate in order to take in account the non-ideality of the system (source current error).
Temp(C) = (PtRES_calculated PtRES_nominal) /alpha
where
Ptres_nominal is the value of the Ptres at 0degC
PtRES_calculated=(VOUT_PtRES/PGA_GAIN)/I_true
(4)
where
VOUT_PtRES is the amplified voltage across the RTD at VOUT pin (ground referred), when the LMP91200 is
I_true is the real current which alternatively flows in the external precison resistance RREF and in the RTD
(5)
I_true=(VOUT_RREF)/(PGA_GAIN*RREF)
where
VOUT_RREF is the amplified voltage across the RREF at VOUT pin (ground referred), when the LMP91200 is
(6)
Inserting Equation 5 and Equation 6 in Equation 4 the temperature is given by the following equation:
Temp(C) = ((VOUT_PtRES /VOUT_RREF)*RREF PtRES_nominal) /alpha
22
(7)
LMP91200
www.ti.com
Table 3.
Bit
Name
Description
D15
MEAS_MODE
Temp measurement
D14
I_MUX
RCAL
[D13:D12]
I_VALUE
00
10
D11
PGA
[D10 :D8]
VCM

measurement.
D7
VOCM
GND
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
100A (Pt1000)
1 mA (Pt100)
10 V/V

Bit
Name
Description
D15
MEAS_MODE
Temp measurement
D14
I_MUX
RTD
[D13:D12]
I_VALUE
00
10
D11
PGA
[D10 :D8]
VCM

measurement.
D7
VOCM
GND
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
100A (Pt1000)
1 mA (Pt100)
10 V/V
The 2-step temperature measurement has a precision of about 0.3C (with RREF @ 0.01% of tolerance) which is
good enough in most of pH meter applications.
3-step measurement
This method requires 3 acquisitions and a precision resistor (RREF) connected between CAL and GND pin, (the
RTD is always connected between RTD and GND pin). The first two acquisitions measure the voltage across the
precision resistor in 2 different conditions (2 different exciting current and 2 PGA gains) in order to remove the
uncertainty of the current source value and the offset of the path. The third acquisition measures the voltage
across the RTD (similar to the 1-step measure), in this case the formula to calculate the temperature is more
complicate in order to take in account the non-ideality of the system (offset, source current error).
Temp(C) = (PtRES_calculated PtRES_nominal) /alpha
where
Ptres_nominal is the value of the Ptres at 0degC
PtRES_calculated=((VOUT_PtRES/PGA_GAIN)-Vos)/I_true
(8)
where
VOUT_PtRES is the amplified voltage across the RTD at VOUT pin (ground referred), when the LMP91200 is
I_true is the real current which alternatively flows in the external precison resistance RREF and in the RTD
Vos is the offset of the path
(9)
23
LMP91200
www.ti.com
Vos=(VOUT_RREF0-VOUT_RREF1)/5
where
VOUT_RREF0 is the amplified voltage across the RREF at VOUT pin (ground referred), when the LMP91200 is
VOUT_RREF 1is the amplified voltage across the RREF at VOUT pin (ground referred), when the LMP91200 is
(10)
I_true=(2*VOUT_RREF1-VOUT_RREF0)/(10*RREF)
(11)
Inserting Equation 9, Equation 10 and Equation 11 in Equation 8 the temperature is given by the following
equation:
Temp(C) = (((VOUT_PtRES/PGA_GAIN)-(VOUT_RREF0-VOUT_RREF1)/5)/((2*VOUT_RREF1-VOUT_RREF0)/(10*RREF))
PtRES_nominal) /alpha
(12)
Table 5.
Bit
Name
Description
D15
MEAS_MODE
Temp measurement
D14
I_MUX
RCAL
[D13:D12]
I_VALUE
01
11
D11
PGA
[D10 :D8]
VCM

measurement.
D7
VOCM
GND
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
200A (Pt1000)
2 mA (Pt100)
5 V/V
Table 6.
Bit
Name
Description
D15
MEAS_MODE
Temp measurement
D14
I_MUX
RCAL
[D13:D12]
I_VALUE
00
10
D11
PGA
[D10 :D8]
VCM

measurement.
D7
VOCM
GND
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
100A (Pt1000)
1 mA (Pt100)
10 V/V

Bit
Name
Description
D15
MEAS_MODE
Temp measurement
D14
I_MUX
RTD
[D13:D12]
I_VALUE
00
10
D11
PGA
[D10 :D8]
VCM

measurement.
D7
VOCM
GND
D6
DIAG_EN
DIAGNOSTIC disabled
[D5 :D0]
RESERVED
RESERVED
24
100A (Pt1000)
1 mA (Pt100)
10 V/V
LMP91200
www.ti.com
The 3-step temperature measurement can reach a precision as high as 0.1C (with RREF @ 0.01% of tolerance)
when the analog signal is acquired by at least 16 bit ADC. With lower number of bit ADC this method gives the
same result of the 2-step measurement due to the low voltage offset of the signal path. As rule of thumb, the 3step temperature measurement gives good result if he the LSB of the ADC is less than the input offset of the
PGA.
Diagnostic Feature
The diagnostic function allows detecting the presence of the sensor and checking the connection of the sensor.
A further analysis of the answer of the pH probe to the diagnostic stimulus allows estimating the aging of the pH
probe. With the diagnostic function is possible to change slightly (+/- 5% VREF) the Common mode voltage. If
the sensor is present it reacts, this reaction gives some information on the status of the connection, the presence
of the sensor and its aging. In fact a typical symptom of the aging of a pH probe is the slowness in the answer. It
means that a pH probe answers with a smoother step to the diagnostic stimulus as its age increases.
The procedure is enabled and disabled by SPI (refer to ). Until bit D6 is at low logic level, VCM stays at the
programmed voltage independently by the SDO_DIAG pin status. When bit D6 is tied at high logic level, on the
first rising edge of SDO_DIAG, a positive pulse is generate. At the second positive rising edge of SDO_DIAG pin,
the positive pulse ends. At the third positive rising edge of SDO_DIAG a negative pulse is generated. At the forth
positive rising edge of the SDO_DIAG the negative pulse ends and the routine is stopped and cannot restart until
bit D6 is set again at 1.
Layout Consideration
In pH measurement, due to the high impedance of the ph Electrode, careful circuit layout and assembly are
required. Guarding techniques are highly recommended to reduce parasitic leakage current by isolating the
LMP91200s input from large voltage gradients across the PC board. A guard is a low impedance conductor that
surrounds an input line and its potential is raised to the input lines voltage. The input pin should be fully guarded
as shown in Figure 56. The guard traces should completely encircle the input connections. In addition, they
should be located on both sides of the PCB and be connected together. The LMP91200 makes the guard ring
easy to be implemented without any other external op amp. The ring needs to be connected to the guard pins
(GUARD1 and GUARD2) which are at the same potential of the INP pin. Solder mask should not cover the input
and the guard area including guard traces on either side of the PCB. Sockets are not recommended as they can
be a significant leakage source. After assembly, a thorough cleaning using commercial solvent is necessary.
In Figure 56 is showed a typical guard ring circuit when the LMP912000 is interfaced to a pH probe trough a
triaxial cable/connector, usually known as 'TRIAX'. The signal conductor and the guard of the triax should be kept
at the same potential; therefore, the leakage current between them is practically zero. Since triax has an extra
layer of insulation and a second conducting sheath, it offers greater rejection of interference than coaxial
cable/connector.
Figure 56. Circuit Board Guard Layout
25
LMP91200
www.ti.com
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C
26
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 25
PACKAGE OPTION ADDENDUM
www.ti.com
22-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty

Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (C)
Top-Side Markings
(3)
(4)
LMP91200MT/NOPB
ACTIVE
TSSOP
PW
16
92
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
LMP912
00MT
LMP91200MTX/NOPB
ACTIVE
TSSOP
PW
16
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
LMP912
00MT
(1)
The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION

www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LMP91200MTX/NOPB
Package Package Pins

Type Drawing
TSSOP
PW
16
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.95
B0
(mm)
K0
(mm)
P1
(mm)
8.3
1.6
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION

www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMP91200MTX/NOPB
TSSOP
PW
16
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as components) are sold subject to TIs terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TIs terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TIs goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or enhanced plastic are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

LMP 91200

Uploaded by

Copyright:

Available Formats

LMP 91200

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LMP 91200

Uploaded by

Copyright:

Available Formats

LMP91200

SNAS571C JANUARY 2012 REVISED MARCH 2013

LMP91200 Configurable AFE for Low-Power Chemical Sensing Applications

The LMP91200 is a configurable sensor AFE for use

Programmable Output Current in Temperature

pH Buffer Input bias current (0<VINP <3.3V)

PRODUCTION DATA information is current as of publication date.

Copyright 20122013, Texas Instruments Incorporated

Figure 1. Top View

Submit Documentation Feedback

Copyright 20122013, Texas Instruments Incorporated

Product Folder Links: LMP91200

SNAS571C JANUARY 2012 REVISED MARCH 2013

Positive Power Supply

Connect an external precision resistor here for purpose of temperature

Pt100/Pt1000 input / internal current source output

Active guard pin

Non-inverting analog input of pH buffer

Active guard pin

High Impedance Programmable Common Mode output

Buffered Programmable Common Mode output

Voltage reference input

Output common mode voltage

Serial Data Out /Diagnostic enable

Chip select, low active.

Absolute Maximum Ratings (1) (2) (3)

Charge Device Model

Voltage between any two pins

Current out at any pin

Storage Temperature Range

Junction Temperature (5)

Operating Ratings (1)

Submit Documentation Feedback

Copyright 20122013, Texas Instruments Incorporated

Product Folder Links: LMP91200

Electrical Characteristics (1) (2) (3)

Temperature measurement mode,

Temperature measurement mode,

Temperature measurement mode,

Temperature measurement mode,

Supply Current (6) (7)

INP=1.65V, 300mV = VOUT = VDD300mV

Open loop Gain

Input Voltage Offset

Input offset voltage drift (8) (9)

Long term VOSpH drift (10)

Input bias current at INP

DC_Common mode rejection

Input referred noise (low

Gain Bandwidth Product (9)

DC_Power supply rejection ratio

500 hours OPL

Integrated 0.1Hz to 10Hz

Submit Documentation Feedback

Copyright 20122013, Texas Instruments Incorporated

Product Folder Links: LMP91200

SNAS571C JANUARY 2012 REVISED MARCH 2013

Electrical Characteristics(1)(2)(3) (continued)

Input referred noise (high