Sample Pages From FDG PDF

4-6
Bending Stresses for Simple Shapes
Section Modulus and

Moment of Inertia
In bending, the maximum stress and amount of deflection can be

calculated in each of the following situations. Additional examples are
available in an engineering handbook.
Section modulus and moment of inertia

depend on the parts geometry and are
listed for several common part
geometries.
= maximum stress at outer fiber
= deflection
I=
bh
12
Z=
bh
6
P = force (load)
W = distributive load
L = length of beam
bh - (b - 2t)(h-2t)
12
Z=
2I
h
Z = section modulus
E = flexural modulus
I = 0.78r 4
r
I = moment of inertia about bending axis
Z = 0.78r 3
Simply Supported Beam, Center Load
P
r
PL
=
4Z
PL
=
48EI
ro
ri
I=
I = 0.78 ( ro4 - ri 4 )
Z = 0.78 (ro4 - ri 4 )
ro
4-7
Simply Supported Beam, Uniform Load
W
WL
=
8Z
5WL
=
384EI
Fixed Supported Beam, Center Load
PL
8Z
PL
192EI
Fixed Supported Beam, Uniform Load

W
WL
=
12Z
WL
=
384EI
Cantilever Beam, End Load
PL
=
3EI
PL
=
Z
Cantilever Beam, Uniform Load
WL
=
2Z
WL
=
8EI
4-8
Finite Element Analysis (FEA)

Overview
FEA is a method for simulating component interaction within a given
operating environment. FEA enables the designer to view several different
design variations without doing extensive testing in the preliminary design
stages. FEA can also be used to prevent overdesigning a part to ensure a
good safety factor, and to reduce the number of design iterations to
reach an optimum profile.
Types of Analysis
FEA allows the user to attempt many different design alternatives based
on various loading conditions, including extended time of load, hightemperature and high moisture conditions. With these analyses, the
designer can look at part optimization and examine how several part
variations can make dramatic differences in part performance. Some of
the forms of analysis are:
Stress Analysis - used to calculate relative stress levels in components
under static or dynamic loads, thermally applied stress, etc.
Deflection Analysis - used to examine how a component will deform
under various loading conditions.
Performing Finite Element

Analysis
USE FEA WHEN

Designing complex shapes
Using unusual loading
(i.e., impact, non-uniform)
Relative results are
important (i.e.,
comparing several
different designs)
4-9
Heat Transfer Analysis - used to show how the temperature will vary
within a component for different boundary conditions and how a
component will deform when there is a thermal differential across the
components surfaces.
Procedure
The designer must provide the following input to the engineer performing
the FEA:
1. A wireframe model that represents the component(s) being analyzed.
The model should have enough detail to accurately portray the critical
areas of the component without attempting to model everything.
2. The physical properties of the material used in the design of the
component.
3. The application of loads and restraints simulating the proposed
operating conditions to be experienced by the component.
Interpretation of FEA results
Once the designer has properly input the parameters of the component(s)
and the analysis has been run, it is necessary to interpret the results. In
general terms, the results from an FEA analysis can be very accurate. It is
the responsibility of the design engineer, however, to realize that FEA is
simply a tool to aid in design.
Typical results from FEA
DESIGN TIP
FEA results should be
verified by proper testing.
4-10
Profile Symmetry
Symmetric profile geometry is generally easier to extrude than nonsymmetric. Hollow profiles with no interior walls are also generally easy to
extrude, regardless of symmetry. A symmetric profile produces a more
uniform transition from the extruder to the entrance of the die. This results
in a more uniform flow of material around the entire profile as it exits the
die. Properly designed profiles not only increase extrusion speed, they
lower residual stresses within a part and provide balanced flow. For more
information on extrusion refer to Section 3 of this guide. Different levels of
symmetry for four profiles are illustrated at left.
Example A is symmetric with no interior walls. This profile represents the
ideal extrusion. A hollow pipe, square or round, is the easiest extrusion.
The simple transition from the extruder to the die entrance allows for easy
control of the material flow across the profile.
Example B is a non-symmetric hollow profile with no interior walls. This
profile is more difficult to extrude than profile A, but the lack of interior
walls results in higher line speeds and lower residual stresses.
A - Easiest
B - Easy

Sample Pages From FDG PDF

Uploaded by

Copyright:

Available Formats

Sample Pages From FDG PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sample Pages From FDG PDF

Uploaded by

Copyright:

Available Formats

4-6

Bending Stresses for Simple Shapes

Section Modulus and

In bending, the maximum stress and amount of deflection can be

Section modulus and moment of inertia

= maximum stress at outer fiber

I = moment of inertia about bending axis

Simply Supported Beam, Center Load

Fixed Supported Beam, Center Load

Fixed Supported Beam, Uniform Load

Cantilever Beam, End Load

Cantilever Beam, Uniform Load

Finite Element Analysis (FEA)

Performing Finite Element

USE FEA WHEN

Typical results from FEA

You might also like