LT89

K ELECTRICAL
SECTION
LT
LIGHTING SYSTEM
CONTENTS
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) AIR BAG and SEAT BELT PRE-TENSIONER .................................................................. 4
HEADLAMP (FOR USA) ............................................ 5
Component Parts and Harness Connector Location..... 5
System Description .................................................. 5
OUTLINE ............................................................... 5
HEADLAMP OPERATION .................................... 6
COMBINATION SWITCH READING FUNCTION..... 6
EXTERIOR LAMP BATTERY SAVER CONTROL..... 6
CAN COMMUNICATION SYSTEM DESCRIPTION ......................................................................... 6
Schematic ................................................................ 7
Wiring Diagram ........................................................ 8
Terminals and Reference Values for BCM ............. 12
Terminals and Reference Values for IPDM E/R ..... 12
How to Perform Trouble Diagnoses ....................... 12
Preliminary Check .................................................. 12
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM .................................................. 12
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR IPDM E/R .......................................... 12
CONSULT-II Function (BCM) ................................. 12
CONSULT-II START PROCEDURE .................... 12
WORK SUPPORT ............................................... 12
DATA MONITOR ................................................. 12
ACTIVE TEST ..................................................... 13
SELF-DIAGNOSTIC RESULTS .......................... 13
CONSULT-II Function (IPDM E/R) ......................... 13
CONSULT-II START PROCEDURE .................... 13
DATA MONITOR ................................................. 14
ACTIVE TEST ..................................................... 14
Headlamp High Beam Does Not Illuminate (Both
Sides) ..................................................................... 14
Headlamp High Beam Does Not Illuminate (One
Side) ....................................................................... 17
High Beam Indicator Lamp Does Not Illuminate ... 18
Headlamp Low Beam Does Not Illuminate (Both
Sides) ..................................................................... 18
Revision: June 2006
Headlamp Low Beam Does Not Illuminate (One

Side) ....................................................................... 21
Headlamps Do Not Turn OFF ................................. 22
Aiming Adjustment .................................................. 23
PREPARATION BEFORE ADJUSTING .............. 23
LOW BEAM AND HIGH BEAM ........................... 23
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 24
Bulb Replacement .................................................. 25
HEADLAMP (HIGH/LOW) ................................... 25
PARKING (CLEARANCE) LAMP ........................ 25
FRONT TURN SIGNAL LAMP ............................ 25
Removal and Installation ........................................ 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Disassembly and Assembly .................................... 26
DISASSEMBLY ................................................... 26
ASSEMBLY ......................................................... 26
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 27
Component Parts and Harness Connector Location... 27
System Description ................................................. 27
OUTLINE ............................................................. 27
HEADLAMP OPERATION ................................... 28
COMBINATION SWITCH READING FUNCTION... 29
EXTERIOR LAMP BATTERY SAVER CONTROL... 29
CAN Communication System Description .............. 29
Schematic ............................................................... 30
Wiring Diagram DTRL ................................... 31
Terminals and Reference Values for BCM .............. 35
Terminals and Reference Values for IPDM E/R ...... 35
How to Perform Trouble Diagnoses ....................... 35
CHECK BCM CONFIGURATION ........................ 35
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM .................................................. 35
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR IPDM E/R .......................................... 35
CONSULT-II Function (BCM) ................................. 35
LT-1
2007 Versa
LT
Daytime Light Control Does Not Operate Properly

(High Beam Headlamps Operate Properly) ............ 35
PREPARATION BEFORE ADJUSTING .............. 37
LOW BEAM AND HIGH BEAM ........................... 37
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 38
HEADLAMP (HIGH/LOW) ................................... 39
PARKING (CLEARANCE) LAMP ......................... 39
FRONT TURN SIGNAL LAMP ............................ 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 39
Disassembly and Assembly .................................... 40
DISASSEMBLY ................................................... 40
ASSEMBLY ......................................................... 40
FRONT FOG LAMP .................................................. 41
OUTLINE ............................................................. 41
FOG LAMP OPERATION .................................... 42
EXTERIOR LAMP BATTERY SAVER CONTROL... 42
Wiring Diagram F/FOG .................................. 43
Terminals and Reference Values for IPDM E/R ...... 45
How to Proceed With Trouble Diagnosis ................ 45
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM ................................................... 45
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR IPDM E/R ........................................... 45
CONSULT-II Function (BCM) .................................. 45
CONSULT-II Function (IPDM E/R) .......................... 45
Front Fog lamps Do Not Illuminate (Both Sides) ... 45
Front Fog Lamp Does Not Illuminate (One Side) ... 48
REMOVAL ........................................................... 50
INSTALLATION .................................................... 50
TURN SIGNAL AND HAZARD WARNING LAMPS... 51
TURN SIGNAL OPERATION ............................... 51
HAZARD LAMP OPERATION ............................. 52
REMOTE KEYLESS ENTRY SYSTEM OPERATION .................................................................... 53
Schematic ............................................................... 54
Wiring Diagram TURN ................................... 55
How to Proceed With Trouble Diagnosis ................ 59
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM ................................................... 59
Revision: June 2006
CONSULT-II Function (BCM) ..................................59

Turn Signals Do Not Operate ..................................59
Front Turn Signal Lamp Does Not Operate ............59
Rear Turn Signal Lamp Does Not Operate .............60
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operates ............................................62
Turn Signal Indicator Lamp Does Not Operate .......63
Bulb Replacement of Front Turn Signal Lamp ........64
Bulb Replacement of Rear Turn Signal Lamp .........64
Removal and Installation of Front Turn Signal Lamp...64
Removal and Installation of Rear Turn Signal Lamp...64
LIGHTING AND TURN SIGNAL SWITCH ................65
Removal and Installation .........................................65
REMOVAL ............................................................65
INSTALLATION ....................................................65
HAZARD SWITCH .....................................................66
REMOVAL ............................................................66
INSTALLATION ....................................................66
COMBINATION SWITCH ..........................................67
Wiring Diagram COMBSW ............................67
Combination Switch Reading Function ...................68
Terminals and Reference Values for BCM ..............68
Combination Switch Inspection ...............................68
STOP LAMP ..............................................................71
Wiring Diagram STOP/L ................................71
Bulb Replacement of High-Mounted Stop Lamp .....72
Bulb Replacement of Rear Combination Lamp for
Stop Lamp ...............................................................72
Removal and Installation of High-Mounted Stop
Lamp .......................................................................72
REMOVAL ............................................................72
INSTALLATION ....................................................72
Removal and Installation of Rear Combination
Lamp for Stop Lamp ................................................72
BACK-UP LAMP .......................................................73
Wiring Diagram BACK/L ................................73
Bulb Replacement ...................................................74
PARKING, LICENSE PLATE AND TAIL LAMPS ......75
Component Parts and Harness Connector Location...75
System Description .................................................75
OPERATION BY LIGHTING SWITCH .................75
COMBINATION SWITCH READING FUNCTION...76
EXTERIOR LAMP BATTERY SAVER CONTROL...76
CAN Communication System Description ..............76
Schematic ...............................................................77
Wiring Diagram TAIL/L ...................................78
Terminals and Reference Values for BCM ..............81
Terminals and Reference Values for IPDM E/R ......81
How to Proceed With Trouble Diagnosis ................81
Preliminary Check ...................................................81
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM ...................................................81
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR IPDM E/R ...........................................81
LT-2
2007 Versa

Parking, License Plate and Tail Lamps Do Not Illuminate .................................................................... 81
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) ............................. 85
PARKING LAMP ................................................. 86
LICENSE PLATE LAMP ...................................... 86
TAIL LAMP .......................................................... 86
PARKING LAMP ................................................. 86
LICENSE PLATE LAMP ...................................... 86
TAIL LAMP .......................................................... 86
REAR COMBINATION LAMP .................................. 87
Components ........................................................... 87
REMOVAL ........................................................... 87
INSTALLATION ................................................... 87
Disaassembly and Assembly ................................. 87
DISSASEMBLY ................................................... 87
ASSEMBLY ......................................................... 88
INTERIOR LAMP ...................................................... 89
Map lamp ............................................................... 89
BULB REPLACEMENT ....................................... 89
REMOVAL AND INSTALLATION ........................ 89
DISASSEMBLY AND ASSEMBLY ...................... 89
Luggage Compartment Lamp ................................ 90
BULB REPLACEMENT ....................................... 90
REMOVAL AND INSTALLATION ........................ 90
INTERIOR ROOM LAMP .......................................... 91
System Description ................................................ 91
POWER SUPPLY AND GROUND ...................... 91
SWITCH OPERATION ........................................ 92
INTERIOR ROOM LAMP TIMER OPERATION... 93
INTERIOR LAMP BATTERY SAVER CONTROL... 94
Schematic ............................................................... 95
Wiring Diagram INT/L .................................... 96
Terminals and Reference Values for BCM ............ 101
How to Proceed With Trouble Diagnosis .............. 101
Preliminary Check ................................................ 101
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM ................................................ 101
CONSULT-II Function (BCM) ............................... 101
CONSULT-II START PROCEDURE .................. 101
WORK SUPPORT ............................................. 101
DATA MONITOR ............................................... 101
ACTIVE TEST ................................................... 102
WORK SUPPORT ............................................. 102
DATA MONITOR ............................................... 102
Interior Room Lamp Control Does Not Operate
(With Map Lamp) .................................................. 103
Interior Room Lamp Control Does Not Operate
(Without Map Lamp) ............................................. 105
Bulb Replacement ................................................ 107
ROOM LAMP .................................................... 107
Removal and Installation ...................................... 107
ROOM LAMP .................................................... 107
ILLUMINATION ....................................................... 108
System Description ............................................... 108
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................ 108
EXTERIOR LAMP BATTERY SAVER CONTROL. 109
CAN Communication System Description ............ 109
Schematic ............................................................. 110
Wiring Diagram ILL .......................................111
Bulb Replacement ................................................ 115
GLOVE BOX LAMP ........................................... 115
BULB SPECIFICATIONS ........................................ 116
Headlamp ............................................................. 116
Exterior Lamp ....................................................... 116
Interior Lamp/Illumination ..................................... 116
LT
Revision: June 2006
LT-3
2007 Versa
PRECAUTIONS
PRECAUTIONS
PFP:00011
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER
EKS00IM8
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Revision: June 2006
LT-4
2007 Versa
HEADLAMP (FOR USA)

HEADLAMP (FOR USA)
Component Parts and Harness Connector Location
PFP:26010
A
EKS00HVB
G
WKIA5469E
1.
IPDM E/R E46, E47 and E48
4.
Combination meter M24
2.
BCM M18 and M20 (view with glove 3.

box removed)
System Description
Combination switch (lighting switch)

M28
EKS00HVC
Headlamp operation is controlled by the BCM (body control module) based on inputs from the combination
switch (lighting switch). When the lighting switch is placed in the 2ND position, the BCM receives an input signal requesting the headlamps (and tail lamps) illuminate. The BCM sends a signal, via the CAN communication lines, to the IPDM E/R (intelligent power distribution module engine room) requesting the headlamps be
turned ON. The CPU (central processing unit) located in the IPDM E/R controls ground for the headlamp high
and headlamp low relay coils. These relays direct power to the respective headlamps, which then illuminate.
LT
OUTLINE
Power is supplied at all times
to headlamp high relay RH and LH (located in IPDM E/R),
to headlamp low relay (located in IPDM E/R),
to ignition relay (located in IPDM E/R),
through 15A fuse (No. 52, located in IPDM E/R) and
through 20A fuse (No. 53, located in IPDM E/R)
to CPU located in IPDM E/R,
through 40A fusible link (letter g , located in fuse and fusible link block)
to BCM terminal 70,
through 10A fuse [No. 8, located in fuse block (J/B)]
to BCM terminal 57, and
to combination meter terminal 27.

With the ignition switch in the ON or START position, power is supplied
to the ignition relay (located in IPDM E/R),
to BCM terminal 38,

Revision: June 2006
LT-5
2007 Versa
HEADLAMP (FOR USA)

With the ignition switch in the ACC or ON position, power is supplied
to BCM terminal 11.

Ground is supplied
to BCM terminal 67
to combination meter terminals 21, 22 and 23
through grounds M57 and M61, and
to IPDM E/R terminals 39 and 59
through grounds E15 and E24.
HEADLAMP OPERATION
Low Beam Operation
With the lighting switch in 2ND position, the BCM receives an input signal requesting the headlamps to illuminate. The BCM then sends a signal, via the CAN communication lines, to the IPDM E/R requesting the low
beam headlamps be turned ON. The CPU located in the IPDM E/R controls ground to the headlamp low relay
coil, which when energized, directs power
through IPDM E/R terminal 54
to headlamp RH terminal 3, and
to headlamp LH terminal 3.
Ground is supplied
to headlamp RH and LH terminals 2

With power and ground supplied, low beam headlamps illuminate.
High Beam Operation/Flash-to-Pass Operation

With the lighting switch in 2ND position and high beam switch in the HIGH position, the BCM receives an input
signal requesting the headlamp high beams to illuminate. The flash to pass feature can be used any time and
also sends a signal to the BCM. This input signal is then communicated to the IPDM E/R and the combination
meter via the CAN communication. The CPU located in the IPDM E/R controls the headlamp high relays (LH
and RH), which when energized, directs power
to headlamp RH terminal 1, and
to headlamp LH terminal 1.
Ground is supplied
to headlamp RH and LH terminal 2

With power and ground supplied, the high beam headlamps illuminate.
The BCM sends a signal, via the CAN communication lines, to the combination meter requesting the high
beam indicator lamp be turned ON.
COMBINATION SWITCH READING FUNCTION

Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL

Refer to LT-76, "EXTERIOR LAMP BATTERY SAVER CONTROL" .
CAN COMMUNICATION SYSTEM DESCRIPTION
EKS00HVD
Refer to LAN-4, "SYSTEM DESCRIPTION" .

Revision: June 2006
LT-6
2007 Versa
HEADLAMP (FOR USA)

Schematic
EKS00ICC
LT
WKWA4971E
Revision: June 2006
LT-7
2007 Versa
HEADLAMP (FOR USA)

Wiring Diagram
EKS00HVG
LKWA0318E
Revision: June 2006
LT-8
2007 Versa
HEADLAMP (FOR USA)

A
LT
LKWA0319E
Revision: June 2006
LT-9
2007 Versa
HEADLAMP (FOR USA)
LKWA0320E
Revision: June 2006
LT-10
2007 Versa
HEADLAMP (FOR USA)

A
LT
LKWA0321E
Revision: June 2006
LT-11
2007 Versa
HEADLAMP (FOR USA)

Terminals and Reference Values for BCM
EKS00HVH
Refer to BCS-12, "Terminals and Reference Values for BCM" .
Terminals and Reference Values for IPDM E/R
EKS00HVI
Refer to PG-25, "Terminals and Reference Values for IPDM E/R" .
How to Perform Trouble Diagnoses

1.
2.
3.
4.
5.
6.
EKS00HVJ
Confirm the symptom or customer complaint.

Understand operation, description and function description. Refer to LT-5, "System Description" .
Perform the Preliminary Check. Refer to LT-12, "Preliminary Check" .
Check symptom and repair or replace the component.
Do the headlamps operate normally? If YES, GO TO 6. If NO, GO TO 4.
INSPECTION END
Preliminary Check
EKS00HVK
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM

Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" .
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR IPDM E/R

Refer to PG-28, "IPDM E/R Power/Ground Circuit Inspection" .
CONSULT-II Function (BCM)
EKS00IM9
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM diagnostic
test item
Diagnostic mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
Inspection by part
SELF-DIAG RESULTS
CAN DIAG SUPPORT MNTR
ECU PART NUMBER
CONFIGURATION
Description
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
Displays BCM input/output data in real time.
Operation of electrical loads can be checked by sending drive signal to them.
Displays BCM self-diagnosis results.
The result of transmit/receive diagnosis of CAN communication can be read.
BCM part number can be read.
Performs BCM configuration read/write functions.
CONSULT-II START PROCEDURE

Refer to BCS-17, "CONSULT-II START PROCEDURE" .
WORK SUPPORT
Display Item List
Item
Description
CONSULT-II
Factory setting
ON
BATTERY SAVER SET
Exterior lamp battery saver control mode can be changed

in this mode. Selects exterior lamp battery saver control
mode between ON/OFF.
OFF
DATA MONITOR
Display Item List
Monitor item
Contents
IGN ON SW
"ON/OFF"
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch signal.
ACC ON SW
"ON/OFF"
Displays "ACC (ON)/OFF, Ignition OFF (OFF)" status judged from ignition switch signal.
HI BEAM SW
"ON/OFF"
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from lighting
switch signal.
Revision: June 2006
LT-12
2007 Versa
HEADLAMP (FOR USA)

Monitor item
Contents
HEAD LAMP SW 1
"ON/OFF"
Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 2 judged from lighting
switch signal.
HEAD LAMP SW 2
"ON/OFF"
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from lighting
switch signal.
LIGHT SW 1ST
"ON/OFF"
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged from lighting switch signal.
PASSING SW
"ON/OFF"
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from lighting switch signal.
FR FOG SW
"ON/OFF"
Displays status (front fog lamp switch: ON/Others: OFF) of front fog lamp switch judged from lighting switch signal.
DOOR SW - DR
"ON/OFF"
Displays status of the front door LH as judged from the front door switch LH signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS
"ON/OFF"
Displays status of the front door RH as judged from the front door switch RH signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW - RR
"ON/OFF"
Displays status of the rear door as judged from the rear door switch (RH) signal. (Door is open:
DOOR SW - RL
"ON/OFF"
Displays status of the rear door as judged from the rear door switch (LH) signal. (Door is open:
BACK DOOR SW
"ON/OFF"
Displays status of the back door as judged from the back door switch signal. (Door is open: ON/
Door is closed: OFF)
TURN SIGNAL R
"ON/OFF"
Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L
"ON/OFF"
Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
ENGINE RUNNote 1
"ON/OFF"
Displays status (Engine running: ON/Others: OFF) as judged from engine status signal.
PKB SWNote 1
"ON/OFF"
Displays status (Parking brake switch: ON/Others: OFF) as judged from parking brake switch signal.
Note 1: Vehicles without daytime light system may display this item, but cannot monitor it.
ACTIVE TEST
Display Item List
Test item
Description
TAIL LAMP
LT
Allows tail lamp relay to operate by switching ON-OFF.
HEAD LAMP
Allows headlamp relay (HI, LO) to operate by switching ON-OFF.
FR FOG LAMP
Allows fog lamp relay to operate by switching ON-OFF.
SELF-DIAGNOSTIC RESULTS
Display Item List
Monitored item
CAN communication
CAN communication system
M
CONSULT-ll display
Description
CAN communication [U1000]
Malfunction is detected in CAN communication.
CAN communication system 1 to 6 [U1000]
Malfunction is detected in CAN system.
CONSULT-II Function (IPDM E/R)
EKS00IMA
IPDM E/R diagnostic Mode
SELF-DIAG RESULTS
DATA MONITOR
Description
Displays IPDM E/R self-diagnosis results.
Displays IPDM E/R input/output data in real time.
ACTIVE TEST

Revision: June 2006
LT-13
2007 Versa
HEADLAMP (FOR USA)

DATA MONITOR
All Items, Main Items, Select Item Menu
CONSULT-II screen
display
Display or
unit
TAIL&CLR REQ
Headlamp low beam

request
Headlamp high beam
request
Item name
Parking, license plate
and tail lamps request
Front fog lamps request

Daytime light request
Monitor item selection

ALL
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
Description
ON/OFF
Signal status input from BCM
HL LO REQ
ON/OFF
HL HI REQ
ON/OFF
FR FOG REQ
ON/OFF
DTRL REQ
ON/OFF
NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the display may not be correct.
ACTIVE TEST
Test item
Tail lamp relay output
Headlamp relay (HI, LO) output
CONSULT-II screen display

TAIL LAMP
LAMPS
Front fog lamp relay (FOG)

output
Description
Allows tail lamp relay to operate by switching operation ON-OFF at
your option.
Allows headlamp relay (HI, LO) to operate by switching operation
(OFF, HI, LO) at your option (Head lamp high beam repeats ON-OFF
every 1 second).
Allows fog lamp relay (FOG) to operate by switching operation ONOFF at your option.
Headlamp High Beam Does Not Illuminate (Both Sides)
EKS00IMB
1. CHECK COMBINATION SWITCH INPUT SIGNAL

With CONSULT-II
1. Select BCM on CONSULT-II. Select HEAD LAMP on
SELECT TEST ITEM screen.
2. Select DATA MONITOR on SELECT DIAG MODE screen.
Make sure that HI BEAM SW turns ON-OFF linked with operation of lighting switch.
When lighting switch is high
position
: HI BEAM SW ON
Without CONSULT-II
Refer to LT-68, "Combination Switch Inspection" .
PKIA7585E
OK or NG
OK
>> GO TO 2.
NG
>> Check combination switch (lighting switch). Refer to LT-68, "Combination Switch Inspection" .
Revision: June 2006
LT-14
2007 Versa
HEADLAMP (FOR USA)
2. HEADLAMP ACTIVE TEST
With CONSULT-II
Select IPDM E/R on CONSULT-II. Select ACTIVE TEST on
SELECT DIAG MODE screen.
2. Select EXTERNAL LAMPS on SELECT TEST ITEM screen.
3. Touch HI screen.
4. Make sure headlamp high beam operates.
1.
Headlamp high beam should operate

(Headlamp high beam repeats ONOFF every 2 seconds).
1.
2.
Without CONSULT-II
Start auto active test. Refer to PG-21, "Auto Active Test" .
Make sure headlamp high beam operates.
PKIC0936E
Headlamp high beam should operate.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3. CHECK IPDM E/R

1.
2.
Select IPDM E/R on CONSULT-II. Select DATA MONITOR

on SELECT DIAG MODE screen.
Make sure HL HI REQ turns ON when lighting switch is in high
position.
When lighting switch is high
position
: HL HI REQ ON
J
OK or NG
OK
>> Replace IPDM E/R. Refer to PG-29, "Removal and
Installation of IPDM E/R" .
NG
>> Replace BCM. Refer to BCS-25, "Removal and Installation of BCM" .
LT
PKIB8696E
4. HEADLAMP HIGH BEAM FUSE INSPECTION

Inspect 10A fuse No. 34 (LH) and fuse No. 35 (RH).
OK or NG
OK
>> GO TO 5.
NG
>> Repair harness.
5. BULB INSPECTION
Inspect inoperative headlamp bulbs.
OK or NG
OK
>> GO TO 6.
NG
>> Replace headlamp bulb. LT-25, "HEADLAMP (HIGH/LOW)" .
Revision: June 2006
LT-15
2007 Versa
HEADLAMP (FOR USA)
6. CHECK HEADLAMP INPUT SIGNAL

1.
2.
3.
4.
5.
6.
With CONSULT-II
Turn ignition switch OFF.
Disconnect headlamp connector.
Select IPDM E/R on CONSULT-II. Select ACTIVE TEST on SELECT DIAG MODE screen.
Select EXTERNAL LAMPS on SELECT TEST ITEM screen.
Touch HI screen.
When headlamp high beam is operating, check voltage between
headlamp harness connector and ground (Headlamp high beam
repeats ONOFF every 2 seconds).
Terminal
(+)
Headlamp connector
1.
2.
3.
4.
RH
E26
LH
E25
Terminal
1
()
Ground
Voltage
Battery voltage
PKIC0960E
Without CONSULT-II
When headlamp high beam is operating, check voltage between headlamp harness connector and
ground.
Terminal
(+)
Headlamp connector
RH
E26
LH
E25
Terminal
1
()
Ground
Voltage
Battery voltage
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 8.
7. CHECK HEADLAMP GROUND CIRCUIT

1.
2.

Check continuity between headlamp harness connector and
ground.
Headlamp connector
RH
E26
LH
E25
Terminal
2
Continuity
Ground
Yes
OK or NG
OK
>> Check front combination lamp connector for damage or
poor connection. Repair as necessary.
NG
>> Repair harness.
Revision: June 2006
LT-16
PKIC0961E
2007 Versa
HEADLAMP (FOR USA)
8. CHECK HEADLAMP CIRCUIT

1.
2.
3.

Disconnect IPDM E/R connector.
Check continuity between IPDM E/R harness connector (A) and
headlamp harness connector (B).
Circuit
RH
LH
Connector
E47
Terminal
Connector
56
E26
55
E25
Terminal
Continuity
Yes
OK or NG
OK
NG
>> Repair harness or connector.
Headlamp High Beam Does Not Illuminate (One Side)
WKIA5470E
EKS00IMC
1. HEADLAMP HIGH BEAM FUSE INSPECTION

Inspect 10A fuse No. 34 (LH) or fuse No. 35 (RH).
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness.
2. CHECK BULB
Check headlamp bulb which does not illuminate.
OK or NG
OK
>> GO TO 3.
NG
>> Replace bulb. Refer to LT-25, "HEADLAMP (HIGH/LOW)" .

1.
2.
3.
4.
LT

Lighting switch is turned to HIGH position.
Check voltage between headlamp harness connector and
ground.
Terminal
(+)
Headlamp connector
RH
E26
LH
E25
Voltage
Terminal
1
()
Ground
Battery voltage
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 5.
Revision: June 2006
WKIA5552E
LT-17
2007 Versa
HEADLAMP (FOR USA)

1.
2.

ground.
Headlamp connector
RH
E26
LH
E25
Terminal
Continuity
Ground
Yes
OK or NG
OK
>> Check connecting condition headlamp harness connector.
NG
PKIC0961E

1.
2.
3.

Circuit
RH
LH
A
Connector
B
Terminal
Connector
56
E26
55
E25
E47
Terminal
Continuity
Yes
OK or NG
OK
NG
High Beam Indicator Lamp Does Not Illuminate
WKIA5470E
EKS00IW4
1. BULB INSPECTION
Inspect CAN communication system. Refer to LAN-44, "TROUBLE DIAGNOSIS" .
OK or NG
OK
>> Replace combination meter. Refer to DI-23, "Removal and Installation" .
NG
>> Repair as necessary.
Headlamp Low Beam Does Not Illuminate (Both Sides)
EKS00IMD

With CONSULT-II
Make sure that HEAD LAMP SW 1 and HEAD LAMP SW 2
turns ON-OFF linked with operation of lighting switch.
When lighting switch is 2ND
position
: HEAD LAMP SW 1 ON
: HEAD LAMP SW 2 ON
Without CONSULT-II
PKIA7586E
OK or NG
OK
>> GO TO 2.
NG
Revision: June 2006
LT-18
2007 Versa
HEADLAMP (FOR USA)
2. CHECK HEADLAMP ACTIVE TEST
With CONSULT-II
3. Touch LO screen.
4. Make sure headlamp low beam operates.
1.
Headlamp low beam should operate.

Without CONSULT-II
1. Start auto active test. Refer to PG-21, "Auto Active Test" .
2. Make sure headlamp low beam operates.
PKIC0936E
Headlamp low beam should operate.

OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3. CHECK IPDM E/R
1.
2.

Make sure HL LO REQ turns ON when lighting switch is in
2ND position.
When lighting switch is 2ND
position
: HL LO REQ ON
OK or NG
OK
NG
>> Replace BCM. Refer toBCS-25, "Removal and Installation of BCM" .
J
PKIA7644E
LT
4. HEADLAMP LOW BEAM FUSE INSPECTION

L

OK or NG
OK
>> GO TO 5.
NG
>> Repair harness.
5. BULB INSPECTION
Inspect inoperative headlamp bulbs.
OK or NG
OK
>> GO TO 6.
NG
>> Replace headlamp bulb.LT-25, "HEADLAMP (HIGH/LOW)" .
Revision: June 2006
LT-19
2007 Versa
HEADLAMP (FOR USA)

1.
2.
3.
4.
5.
6.
With CONSULT-II
Select IPDM E/R on CONSULT-II. Select ACTIVE TEST on SELECT DIAG MODE screen.
Touch LO screen.
When headlamp low beam is operating, check voltage between
headlamp harness connector and ground.
Terminal
(+)
Headlamp connector
1.
2.
3.
4.
RH
E26
LH
E25
Terminal
3
()
Ground
Voltage
Battery voltage
Without CONSULT-II
PKIC0963E
When headlamp low beam is operating, check voltage between headlamp harness connector and ground.
Terminal
(+)
Headlamp connector
RH
E26
LH
E25
()
Voltage
Terminal
3
Ground
Battery voltage
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 8.

1.
2.

Check continuity between headlamp harness connector (B) and
ground.
Headlamp connector
RH
E26
LH
E25
Terminal
2
Continuity
Ground
Yes
OK or NG
OK
>> Check front combination lamp connector for damage or
poor connection. Repair as necessary.
NG
>> Repair harness.
Revision: June 2006
LT-20
PKIC0961E
2007 Versa
HEADLAMP (FOR USA)

1.
2.
3.

Circuit
RH
LH
A
Connector
E47
B
Terminal
Connector
54
E26
52
E25
Terminal
Continuity
Yes
OK or NG
OK
NG
Headlamp Low Beam Does Not Illuminate (One Side)
WKIA5471E
EKS00IME
1. HEADLAMP LOW BEAM FUSE INSPECTION

OK or NG
OK
>> GO TO 2.
NG
>> Repair harness.
2. CHECK BULB
Check bulb of headlamp which does not illuminate.
OK or NG
OK
>> GO TO 3.
NG
>> Replace bulb. Refer to LT-25, "HEADLAMP (HIGH/LOW)" .

1.
2.
3.
4.
LT

Lighting switch is turned to 2ND position.
Check voltage between headlamp harness connector and
ground.
Terminal
(+)
Headlamp connector
RH
E26
LH
E25
Voltage
Terminal
3
()
Ground
Battery voltage
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 5.
Revision: June 2006
WKIA5551E
LT-21
2007 Versa
HEADLAMP (FOR USA)

1.
2.

ground.
Headlamp connector
RH
E26
LH
E25
Terminal
Continuity
Ground
Yes
OK or NG
OK
>> Check condition of headlamp harness connector.
NG
PKIC0961E

1.
2.
3.

Circuit
RH
LH
A
Connector
E47
B
Terminal
Connector
54
E26
52
E25
Terminal
Continuity
Yes
OK or NG
OK
>> Replace IPDM E/R. Refer to PG-28, "IPDM E/R Power/
Ground Circuit Inspection" .
NG
Headlamps Do Not Turn OFF
WKIA5471E
EKS00IMF
1. CHECK HEADLAMPS TURN OFF

Make sure that lighting switch is OFF. Make sure headlamp turns OFF when ignition switch is turned OFF.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.

1.
2.
Select BCM on CONSULT-II. Select HEAD LAMP on

Select DATA MONITOR on SELECT DIAG MODE screen.
Make sure that HEAD LAMP SW 1 and HEAD LAMP SW 2
turns ON-OFF linked with operation of lighting switch.
When lighting switch is OFF
position
: HEAD LAMP SW 1 OFF

: HEAD LAMP SW 2 OFF
OK or NG
OK
NG
>> Check combination switch (lighting switch). Refer to LT68, "Combination Switch Inspection" .
Revision: June 2006
LT-22
PKIA7588E
2007 Versa
HEADLAMP (FOR USA)
3. CHECKING CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R
Select BCM on CONSULT-II, and perform self-diagnosis for

BCM.
Display of self-diagnosis results
NO DTC>> Replace IPDM E/R. Refer to PG-29, "Removal and
CAN COMM CIRCUIT>> Refer to LAN-44, "TROUBLE DIAGNOSIS" .
D
PKIA7627E
Aiming Adjustment
EKS00IMG
WKIA5417E
1.
Headlamp
A.
Inner and outer adjustment
B.
LT
Adjusting screw
PREPARATION BEFORE ADJUSTING

Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level surface.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM

1.
2.
Turn headlamp low beam ON.

Use adjusting screw to perform aiming adjustment.
Revision: June 2006
LT-23
2007 Versa
HEADLAMP (FOR USA)

ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
WKIA4287E
A.
Right
B.
Vertical center line of headlamp
C.
Horizontal aiming center line of

headlamp
D.
Left
E.
Vertical aiming cutoff point
F.
Cutoff line for vertical aiming evaluation
G.
Acceptable vertical cutoff setting at

horizontal aiming point
H.
Horizontal center line of headlamp
J.
Maximum acceptable vertical aiming

point
K.
Minimum acceptable vertical aiming

point
L.
Aiming distance from center of

headlamp to aiming screen
Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
For horizontal headlamp aiming, adjust headlamp until beam pattern is at horizontal center point.
For vertical headlamp aiming, adjust headlamp until beam pattern is positioned per specified dimensions.
Description
Halogen Headlamp
Vertical aiming cutoff point (E)
53.2 mm (2.094 in.)
Minimum acceptable vertical aiming point (K)
4 mm (0.157 in.)
Maximum acceptable vertical aiming point (J)
30 mm (1.181 in.)
Aiming distance from center of headlamp to aiming screen (L)
Revision: June 2006
LT-24
10,000 mm (393.70 in.)
2007 Versa
HEADLAMP (FOR USA)

Bulb Replacement
EKS00IMH
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to ensure watertightness.
HEADLAMP (HIGH/LOW)
1.
2.
3.
4.
Turn lighting switch OFF.

Remove the headlamp. Refer to LT-25, "Removal and Installation" .
Remove back cover.
Unlock retaining spring and remove bulb from headlamp.
PARKING (CLEARANCE) LAMP

1.
2.
3.
4.

Turn bulb socket counterclockwise and unlock it.
Remove bulb from its socket.
FRONT TURN SIGNAL LAMP

1.
2.
3.
4.

Removal and Installation
G
EKS00IMI
REMOVAL
1.
2.
3.
4.
Disconnect the negative battery terminal.

Remove front bumper fascia. Refer to EI-14, "FRONT BUMPER" .
Remove headlamp bolts (A).
Pull headlamp (1) toward the vehicle front, disconnect connector, and remove headlamp.
LT
PKIC1223E
INSTALLATION
Installation is in the reverse order of removal.
After installation, perform aiming adjustment. Refer to LT-23, "Aiming Adjustment" .
Revision: June 2006
LT-25
2007 Versa
HEADLAMP (FOR USA)

Disassembly and Assembly
EKS00IMJ
WKIA5418E
1.
Retaining spring
2.
Parking (clearance) lamp bulb
3.
Parking (clearance) lamp bulb socket
4.
Halogen bulb (High/Low)
5.
Back cover
6.
Front turn signal lamp bulb socket
7.
Front turn signal lamp bulb
8.
Headlamp housing assembly
9.
Bumper stay
A.
Screw
DISASSEMBLY
1.
2.
3.
4.
5.
6.
7.
Remove back cover.

Unlock retaining spring and remove bulb (High/Low).
Turn parking (clearance) lamp bulb socket counterclockwise and unlock it.
Remove parking (clearance) lamp bulb from its socket.
Turn front turn signal lamp bulb socket counterclockwise and unlock it.
Remove front turn signal lamp bulb from its socket.
Remove the bumper stay.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
After installing bulb, be sure to install plastic cap securely to insure water tight seal.
Revision: June 2006
LT-26
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM Component Parts and Harness Connector Location
PFP:26010
A
EKS00ICD
G
WKIA5555E
1.
IPDM E/R E43, E46, E47 and E48
2.

box removed)

M28
4.
5.
Daytime light relay 1 E37 and daytime light relay 2 E38
Parking brake switch M17
6.
System Description
EKS00ICE
Headlamp operation is controlled by the BCM (body control module) based on inputs from the combination
switch (lighting switch). When the lighting switch is placed in the 2ND position, the BCM receives an input signal requesting the headlamps (and tail lamps) illuminate. The request is then communicated to the IPDM E/R J
(intelligent power distribution module engine room) via the CAN communication lines. The CPU (central processing unit) located in the IPDM E/R controls ground for the headlamp high and headlamp low relay coils.
These relays direct power to the respective headlamps, which then illuminate. When the headlamp switch is
LT
OFF or in the 1ST position (parking lamps ON), the parking brake is released and the engine is running, the
IPDM E/R de-energizes the headlamp relays and supplies ground to the daytime light relay 1 to actuate the
daytime light function.
L
OUTLINE
to headlamp high relay RH and LH (located in IPDM E/R)
to headlamp low relay (located in IPDM E/R) and
to ignition relay (located in IPDM E/R)
through 40A fusible link (letter g , located in fuse and fusible link box)
to BCM terminal 70,
to BCM terminal 57,
to combination meter terminal 27,
through 10A fuse (No. 26, located in fuse and fusible link box)
to the daytime light relay 1.

Revision: June 2006
LT-27
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM to the ignition relay (located in IPDM E/R),
to BCM terminal 38,

to BCM terminal 11.

Ground is supplied
to BCM terminal 67 and
through grounds M57 and M61,
through grounds E15 and E24,
HEADLAMP OPERATION
Low Beam Operation
With the lighting switch in 2ND position, the BCM receives an input signal requesting the headlamps to illuminate. This input signal is communicated to the IPDM E/R via the CAN communication lines. The CPU located
in the IPDM E/R controls the headlamp low relay coil, which when energized, directs power
to daytime light relay 2 terminals 1 and 5 (energizing the relay),
through daytime light relay 2 terminal 3
to front combination lamp RH terminal 3, and
to front combination lamp LH terminal 3.

Ground is supplied
to front combination lamp LH terminal 2
to headlamp RH terminal 2 via
daytime light relay 1 terminals 3 and 4

With power and ground supplied, low beam headlamps illuminate.
High Beam/Flash-to-Pass Operation

With the lighting switch in 2ND position and high beam switch in the HIGH position, the BCM receives input
signal requesting the headlamp high beams to illuminate. The flash-to-pass feature can be used any time and
also sends a signal to the BCM. This input signal is communicated to the IPDM E/R and the combination
meter via the CAN communication lines. The CPU located in the IPDM E/R controls the headlamp high relay
coil, which when energized, directs power
to front combination lamp RH terminal 1, and
to front combination lamp LH terminal 1.

Ground is supplied
through grounds E15 and E24, and

Revision: June 2006
LT-28
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM to front combination lamp RH terminal 2 via
daytime light relay 1 terminals 3 and 4

With power and ground supplied, the high beam headlamps illuminate.
The BCM sends a signal to the combination meter requesting the high beam indicator lamp to turn ON.
Daytime Light System Operation

With the lighting switch in the OFF or 1ST position (parking lamps ON), the BCM receives inputs requesting
the headlights off. If the parking brake is released and the engine is running, the BCM then sends a signal, via
the CAN communication lines, requesting the IPDM E/R to activate the daytime light system. The CPU located
in the IPDM E/R controls the daytime light relay 1 coil, which when energized, directs power
from daytime light relay 1 terminal 3
to front combination lamp RH terminal 2,
through front combination lamp RH high beam terminal 1
to IPDM E/R terminal 56,
through both de-energized headlamp high relays
to 10A fuse (No. 35, located in IPDM E/R),
to front combination lamp LH terminal high beam 1.

Ground is supplied
to daytime light relay 1 terminal 1
through IPDM E/R terminal 6.

With power and ground supplied, high beam headlamps illuminate at reduced intensity.

J

CAN Communication System Description
LT
EKS00ICF
Refer to LAN-4, "CAN Communication System" .
Revision: June 2006
LT-29
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM Schematic
EKS00ICH
WKWA4972E
Revision: June 2006
LT-30
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM Wiring Diagram DTRL
EKS00ICI
LT
LKWA0322E
Revision: June 2006
LT-31
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
LKWA0323E
Revision: June 2006
LT-32
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM A
LT
LKWA0324E
Revision: June 2006
LT-33
2007 Versa
LKWA0325E
Revision: June 2006
LT-34
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM Terminals and Reference Values for BCM
EKS00ICJ
Refer to BCS-12, "Terminals and Reference Values for BCM"
EKS00ICK
How to Perform Trouble Diagnoses

1.
2.
3.
4.
5.
6.
EKS00ICL

Understand operation, description and function description. Refer to LT-27, "System Description" .
Does the daytime light system operate normally? If YES, GO TO 6. If NO, GO TO 4.
INSPECTION END
Preliminary Check
E
EKS00IM0
CHECK BCM CONFIGURATION
1. CHECK BCM CONFIGURATION
Confirm BCM configuration for "DTRL" is set to "WITH". Refer toBCS-19, "READ CONFIGURATION PROCEDURE" .
OK or NG
OK
>> Continue preliminary check. Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" .
NG
>> Change BCM configuration for "DTRL" to "WITH". Refer to BCS-21, "WRITE CONFIGURATION
PROCEDURE" .

I

J
EKS00IM1
Refer to LT-12, "CONSULT-II Function (BCM)" .
LT
EKS00IM2
Refer to LT-13, "CONSULT-II Function (IPDM E/R)" .
Daytime Light Control Does Not Operate Properly (High Beam Headlamps Operate Properly)
EKS00IM3
1. CHECK DAYTIME LIGHT RELAY 1 FUSE
Inspect daytime light relay fuse 10A fuse (No. 26, located in the fuse and fusible link box).
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness.
Revision: June 2006
LT-35
2007 Versa
2. CHECK DAYTIME LIGHT RELAY 1 POWER SUPPLY CIRCUIT

1.
2.
3.

Remove daytime light relay 1.
Check voltage between daytime light relay 1 harness connector
E37 terminals 2, 5 and ground.
2, 5 - Ground
: Battery voltage should exist.
OK or NG
OK
>> GO TO 3.
NG
WKIA3305E
3. CHECK DAYTIME LIGHT RELAY 1

1.
2.
Apply battery voltage to daytime light relay 1 terminal 2 and supply ground to terminal 1.
Check continuity between terminals 3 and 5.
3-5
: Continuity should exist.
OK or NG
OK
>> GO TO 4.
NG
>> Replace daytime light relay 1.
WIIA0291E
4. CHECK INPUT SIGNAL

1.
2.
3.
Connect daytime light relay 1.

Start engine and release parking brake. Headlamp switch OFF.
Select "IPDM E/R" on CONSULT-II. With DATA MONITOR,
make sure "DTRL REQ" turns ON-OFF linked with operation of
parking brake switch.
Parking brake ON
Parking brake OFF
: DTRL REQ ON
: DTRL REQ OFF
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
WKIA1449E
5. CHECKING CAN COMMUNICATIONS

Select "BCM" on CONSULT-II and perform self-diagnosis for BCM.
Displayed self-diagnosis results
NO DTC>>Replace BCM. Refer to BCS-25, "Removal and Installation of BCM" .
CAN COMM CIRCUIT>> Check BCM CAN communication system.
Refer to LAN-44, "TROUBLE DIAGNOSIS" .
SKIA1039E
Revision: June 2006
LT-36
2007 Versa
6. CHECK DAYTIME LIGHT RELAY 1 CONTROL CIRCUIT

1.
2.
3.
4.

Disconnect daytime light relay 1 connector E37.
Disconnect IPDM E/R connector E43.
Check continuity between IPDM E/R connector E43 (A) terminal
6 and daytime light relay 1 connector E37 (B) terminal 1.
C
A
Continuity
Connector
Terminal
Connector
Terminal
E43
E37
Yes
OK or NG
OK
>> Replace the IPDM E/R. Refer to PG-29, "Removal and
NG
E
WKIA5553E
Aiming Adjustment
EKS00IM4
LT
WKIA5417E
1.
Headlamp
A.
Inner and outer adjustment
B.
PREPARATION BEFORE ADJUSTING

Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level surface.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
LOW BEAM AND HIGH BEAM

1.
2.
Turn headlamp low beam ON.

Use adjusting screw to perform aiming adjustment.
Revision: June 2006
LT-37
Adjusting screw
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
WKIA4287E
A.
Right
B.
Vertical center line of headlamp
C.
Horizontal aiming center line of

headlamp
D.
Left
E.
Vertical aiming cutoff point
F.
Cutoff line for vertical aiming evaluation
G.
Acceptable vertical cutoff setting at

horizontal aiming point
H.
Horizontal center line of headlamp
J.
Maximum acceptable vertical aiming

point
K.
Minimum acceptable vertical aiming

point
L.
Aiming distance from center of

headlamp to aiming screen
Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
For horizontal headlamp aiming, adjust headlamp until beam pattern is at horizontal center point.
For vertical headlamp aiming, adjust headlamp until beam pattern is positioned per specified dimensions.
Description
Halogen Headlamp
Vertical aiming cutoff point (E)
53.2 mm (2.094 in.)
Minimum acceptable vertical aiming point (K)
4 mm (0.157 in.)
Maximum acceptable vertical aiming point (J)
30 mm (1.181 in.)
Aiming distance from center of headlamp to aiming screen (L)
Revision: June 2006
LT-38
10,000 mm (393.70 in.)
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM Bulb Replacement
EKS00IM5
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to ensure watertightness.
HEADLAMP (HIGH/LOW)
1.
2.
3.
4.

Remove back cover.
Unlock retaining spring and remove bulb from headlamp.
PARKING (CLEARANCE) LAMP

1.
2.
3.
4.

FRONT TURN SIGNAL LAMP

1.
2.
3.
4.

G
EKS00IM6
REMOVAL
1.
2.
3.
4.
Disconnect the negative battery terminal.

Remove front bumper fascia. Refer to EI-14, "FRONT BUMPER" .
Remove headlamp bolts (A).
Pull headlamp (1) toward the vehicle front, disconnect connector, and remove headlamp.
LT
PKIC1223E
INSTALLATION
After installation, perform aiming adjustment. Refer to LT-37, "Aiming Adjustment" .
Revision: June 2006
LT-39
2007 Versa
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM Disassembly and Assembly
EKS00IM7
WKIA5418E
1.
Retaining spring
2.
Parking (clearance) lamp bulb
3.
Parking (clearance) lamp bulb socket
4.
Halogen bulb (High/Low)
5.
Back cover
6.
Front turn signal lamp bulb socket
7.
Front turn signal lamp bulb
8.
Headlamp housing assembly
9.
Bumper stay
A.
Screw
DISASSEMBLY
1.
2.
3.
4.
5.
6.
7.
Remove back cover.

Unlock retaining spring and remove bulb (High/Low).
Turn parking (clearance) lamp bulb socket counterclockwise and unlock it.
Remove parking (clearance) lamp bulb from its socket.
Turn front turn signal lamp bulb socket counterclockwise and unlock it.
Remove front turn signal lamp bulb from its socket.
ASSEMBLY
CAUTION:
After installing bulb, be sure to install plastic cap securely to insure water tight seal.
Revision: June 2006
LT-40
2007 Versa
FRONT FOG LAMP

FRONT FOG LAMP
PFP:26150
A
EKS00HX5
D
WKIA5554E
1.
2.
BCM M18 and M20 (viewed with

glove box removed)
3.
System Description

M28
EKS00HX6
The front fog lamps are controlled by lighting switch inputs to the BCM (body control module). The lighting
switch must be in the 1ST or 2ND position with the high beams OFF before the BCM will request the IPDM E/
R (intelligent power distribution module engine room) to turn the front fog lamps on. The BCM requests the
front fog lamps over the CAN communication lines to the IPDM E/R. The CPU (central processing unit) of the
IPDM E/R controls the front fog lamp relay coil ground. When energized, the relay directs power to the front
fog lamps.
OUTLINE
Power is supplied at all times:
to front fog lamp relay (located in IPDM E/R),
through 40A fusible link (letter g , located in the fuse and fusible link box)
to BCM terminal 70,
to BCM terminal 57,

With the ignition switch in the ON or START position, power is supplied:
to BCM terminal 38.

to BCM terminal 11.

Ground is supplied
to BCM terminal 67
Revision: June 2006
LT-41
LT
2007 Versa
FRONT FOG LAMP

FOG LAMP OPERATION
The front fog lamp switch is built into the lighting switch. The lighting switch must be in 1ST position or 2ND
position and front fog lamp switch must be ON position for front fog lamp operation. The fog lamp will not operate with the high beam headlamps ON.
When the front fog lamp switch is in the ON position, the BCM sends a request, via the CAN communication
lines, to the CPU of the IPDM E/R to ground the coil side of the front fog lamp relay. The front fog lamp relay
then directs power
to front fog lamp LH terminal 1, and
to front fog lamp RH terminal 1.

Ground is supplied
to front fog lamp terminal 2,

With power and grounds supplied, front fog lamps illuminate.


EKS00HX7
Revision: June 2006
LT-42
2007 Versa
FRONT FOG LAMP

Wiring Diagram F/FOG
EKS00HXA
LT
LKWA0326E
Revision: June 2006
LT-43
2007 Versa
FRONT FOG LAMP
LKWA0327E
Revision: June 2006
LT-44
2007 Versa
FRONT FOG LAMP

EKS00HXB
EKS00HXC
How to Proceed With Trouble Diagnosis

1.
2.
3.
4.
5.
6.
EKS00HXD

Understand operation description and function description. Refer to LT-41, "System Description" .
Do the front fog lamps operate normally? If YES, GO TO 6. If NO, GO TO 4.
INSPECTION END.
Preliminary Check
E
EKS00HXE


G
EKS00HXF
Refer to BCS-17, "CONSULT-II Function (BCM)" .

H
EKS00HXG
Refer to PG-19, "CONSULT-II Function (IPDM E/R)" .
Front Fog lamps Do Not Illuminate (Both Sides)
EKS00HXH
1. INSPECT FOG LAMP FUSE

J
Inspect fog lamp 15A fuse No. 56 in IPDM E/R.

OK or NG
OK
>> GO TO 2.
NG
>> Repair harness.
LT

L
1.
2.
Select BCM on CONSULT-II. Select HEAD LAMP on

Select DATA MONITOR on SELECT DIAG MODE screen.
Make sure that FR FOG SW turns ON-OFF linked with operation of fog lamp switch.
When fog lamp switch is ON
: FR FOG SW ON
With CONSULT-II
Select BCM on CONSULT-II. With HEAD LAMP data monitor,
make sure FR FOG SW turns ON-OFF linked with operation of
PKIA7598E
front fog lamp switch.
Without CONSULT-II
OK or NG
OK
>> GO TO 3.
NG
Revision: June 2006
LT-45
2007 Versa
FRONT FOG LAMP
3. FOG LAMP ACTIVE TEST

With CONSULT-II
3. Touch FOG screen.
4. Make sure front fog lamp operates.
1.
Front fog lamp should operate.

1.
2.
Without CONSULT-II
Make sure front fog lamp operates.
PKIC0936E
Front fog lamp should operate.

OK or NG
OK
>> GO TO 4.
NG
>> GO TO 5.
4. CHECK IPDM E/R

1.
2.

Make sure FR FOG REQ turns ON when front fog lamp switch
is in ON position.
When front fog lamp switch
is ON position
: FR FOG REQ ON
OK or NG
OK
NG
>> Replace BCM. Refer toBCS-25, "Removal and Installation of BCM" .
Revision: June 2006
LT-46
SKIA5898E
2007 Versa
FRONT FOG LAMP
5. CHECK FOG LAMP INPUT SIGNAL

1.
2.
3.
4.
5.
6.
With CONSULT-II
Disconnect front fog lamp connector.
Select IPDM E/R on CONSULT-II, and select ACTIVE TEST on SELECT DIAG MODE screen.
Touch FOG screen.
When front fog lamp relay is operating, check voltage between
front fog lamp harness connector and ground.
(+)
()
Front fog lamp connector
1.
2.
3.
4.
RH
E28
LH
E27
Ground
(+)
E28
LH
E27
Battery voltage
()
Voltage
Ground
Battery voltage
RH
LT
LH
E47
Terminal
Connector
51
E28
50
E27
B
Terminal
Continuity
Yes
OK or NG
OK
NG
Revision: June 2006

front fog lamp harness connector (B).
Connector
I
1
6. CHECK FOG LAMP CIRCUIT
Circuit
Terminal
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
1.
2.
3.
Without CONSULT-II
PKIA6276E
When front fog lamp relay is operating, check voltage between front fog lamp harness connector and
ground.
RH
Voltage
Terminal
1
LT-47
WKIA4408E
2007 Versa
FRONT FOG LAMP
7. CHECK FOG LAMP GROUND

1.
Check continuity between front fog lamp harness connector and

ground.
RH
E28
LH
E27
Terminal
Continuity
Ground
Yes
OK or NG
OK
>> Check front fog lamp bulbs.
NG
PKIA6277E
Front Fog Lamp Does Not Illuminate (One Side)
1.
EKS00HXI
CHECK BULB
Check bulb of lamp which does not illuminate.

OK or NG
OK
>> GO TO 2.
NG
>> Replace front fog lamp bulb.
2. CHECK FOG LAMP CIRCUIT

1.
2.
3.

Disconnect IPDM E/R connector and front fog lamp connector.
front fog lamp harness connector (B).
Circuit
RH
A
Connector
B
Terminal
Connector
51
E28
50
E27
E47
LH
Terminal
Continuity
Yes
OK or NG
OK
>> GO TO 3.
NG
WKIA4408E
3. CHECK FOG LAMP GROUND

1.
Check continuity between front fog lamp harness connector and

ground.
RH
E28
LH
E27
Terminal
2
Continuity
Ground
Yes
OK or NG
OK
NG
Revision: June 2006
LT-48
PKIA6277E
2007 Versa
FRONT FOG LAMP

Aiming Adjustment
EKS00HXJ
The front fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing
aiming adjustment, make sure of the following.
Keep all tires inflated to correct pressure.
Place vehicle on level surface.
Set that there is no-load in vehicle other than the driver (or equivalent weight placed in drivers position).
Adjust aiming in the vertical direction by turning the adjusting screw (A).
F
PKIC1070E
1.
2.
3.
Set the distance (C) between the screen and the center of front
fog lamp lens (E) as shown.
Turn front fog lamps (1) to ON.
Adjust front fog lamps using adjusting screw so that the top edge
of the high intensity zone (A) is as shown.
Aiming distance from center of fog lamp to screen (C)
25,000 mm (984.3 in)
Foglamp beam width (D)
870 mm (34.3 in)
Horizontal distance from ground to bottom edge of high

intensity zone (B)
220 mm (8.7 in)
Horizontal distance from bottom edge to top edge of

high intensity zone (A)
21.75 mm (0.9 in)
LT
NOTE:
When performing adjustment, if necessary, cover the headlamps
and opposite front fog lamp.
M
WKIA5419E
Bulb Replacement
1.
2.
3.
4.
5.
EKS00HXK

Turn off the fender protector (front) to obtain work space
between the fender protector and fender.
Disconnect front fog lamp connector (1).
Turn bulb socket (2) counterclockwise unlock and remove it.
PKIC1071E
Revision: June 2006
LT-49
2007 Versa
FRONT FOG LAMP

EKS00HXL
WKIA5420E
1.
Front fog lamp
2.
Front bumper finisher
3.
Bolt
REMOVAL
1.
2.
3.
4.
Turn over the fender protector and undercover to obtain work space between the fender protector and
fender.
Remove pawl, and front bumper finisher from front bumper.
Remove bolt and remove front fog lamp from bracket.
INSTALLATION
Revision: June 2006
LT-50
2007 Versa
TURN SIGNAL AND HAZARD WARNING LAMPS

PFP:26120
A
EKS00HXZ
G
WKIA5493E
1.
BCM M18 and M20 (view with glove

box removed)
4.
2.
Hazard switch M55
3.
System Description

M28
EKS00HY0
TURN SIGNAL OPERATION
through 40A fusible link (letter g , located in the fuse and fusible link box)
to BCM (body control module) terminal 70,
through 10A fuse [No. 8, located in the fuse block (J/B)]
to BCM terminal 57,

to BCM terminal 38,

to BCM terminal 11.

Ground is supplied
through grounds M57 and M61.
LT
LH Turn Signal Lamp

When the turn signal switch is moved to the left turn position, the BCM receives an input signal requesting left
turn signals to flash. The BCM then supplies power
through BCM terminal 60
to front combination lamp LH terminal 4 and
to rear combination lamp LH terminal 6.

Revision: June 2006
LT-51
2007 Versa

Ground is supplied
to rear combination lamp LH terminal 1
through grounds B7 and B19.

The BCM also sends a request, via the CAN communication lines, to the combination meter to flash the left
turn signal indicator. The unified meter control unit in the combination meter supplies ground to the left turn
signal indicator lamp and activates the audible turn signal indicator.
With power, ground and input supplied, the BCM controls the flashing of the turn signal lamps.
RH Turn Signal Lamp

When turn signal switch is moved to the right turn position, the BCM receives an input signal requesting right
turn signals to flash. The BCM then supplies power
to front combination lamp RH terminal 4 and
to rear combination lamp RH terminal 6.

Ground is supplied
to front combination lamp RH terminal 5
to rear combination lamp RH terminal 1
through grounds B117, B132 and B402.

The BCM also sends a request, via the CAN communication lines, to the combination meter to flash the right
turn signal indicator. The unified meter control unit in the combination meter supplies ground to the right turn
signal indicator lamp and activates the audible turn signal indicator.
With power, ground and input supplied, the BCM controls the flashing of the turn signal lamps.
HAZARD LAMP OPERATION

through 40A fusible link (letter g , located in fuse, fusible link and relay box)
to BCM terminal 70,
to BCM terminal 57,

Ground is supplied
to hazard switch terminal 1,

When hazard switch is depressed, ground is supplied
through hazard switch terminal 2
to BCM terminal 29.

BCM then supplies power
through BCM terminal 60,
to front combination lamp RH terminal 4 and
through BCM terminal 61.

Ground is supplied
to front combination lamp LH and RH terminal 5

Revision: June 2006
LT-52
2007 Versa

through grounds B7 and B19,
through grounds B117, B132 and D402.

The BCM also supplies input to combination meter across the CAN communication lines. This input is processed by unified meter control unit in combination meter, which in turn supplies ground to the left and right
turn signal indicator lamps.
With power and input supplied, BCM controls flashing of hazard warning lamps.
REMOTE KEYLESS ENTRY SYSTEM OPERATION

D
through 40A fusible link (letter g , located in fuse, fusible link and relay box)
to BCM terminal 70,

E

Ground is supplied
F

G
When the remote keyless entry system is triggered by input from the keyfob, the BCM supplies power

H
to rear combination lamp LH terminal 6,
to front turn signal lamp RH terminal 4 and

I

Ground is supplied
J
to front combination lamp LH and RH terminals 5

LT
through grounds B7 and B19,

L
The BCM also supplies input to combination meter via the CAN communication lines. This input is processed
by the unified meter control unit in combination meter, which in turn supplies ground to the left and right turn
signal indicator lamps.
With power and ground supplied, BCM controls flashing of hazard warning lamps when keyfob is used to acti- M
vate remote keyless entry system.

Refer toBCS-3, "COMBINATION SWITCH READING FUNCTION" .
EKS00HY1
Revision: June 2006
LT-53
2007 Versa

Schematic
EKS00HY3
WKWA4974E
Revision: June 2006
LT-54
2007 Versa

Wiring Diagram TURN
EKS00HY4
LT
LKWA0329E
Revision: June 2006
LT-55
2007 Versa
LKWA0330E
Revision: June 2006
LT-56
2007 Versa

A
LT
LKWA0331E
Revision: June 2006
LT-57
2007 Versa
LKWA0332E
Revision: June 2006
LT-58
2007 Versa

EKS00HY5

1.
2.
3.
4.
5.
6.
EKS00HY6

Perform the preliminary check. Refer to LT-59, "Preliminary Check" .
Do turn signal and hazard warning lamps operate normally? If YES, GO TO 6. If NO, GO TO 4.
INSPECTION END
Preliminary Check
D
EKS00HY7

E
EKS00HY8
Turn Signals Do Not Operate
EKS00HY9
With CONSULT-II
Select BCM on CONSULT-II. Select FLASHER on SELECT
TEST ITEM screen.
Make sure that TURN SIGNAL R and TURN SIGNAL L turns
ON-OFF linked with operation of lighting switch.
1.
When turn signal switch is

right position
When turn signal switch is
left position
: TURN SIGNAL R ON
J
: TURN SIGNAL L ON
PKIA7600E
Without CONSULT-II
OK or NG
OK
>> Replace the BCM. BCS-25, "Removal and Installation of BCM"
NG
Front Turn Signal Lamp Does Not Operate
EKS00IXB
1. CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-116, "Exterior Lamp" .
OK or NG
OK
>> GO TO 2.
NG
>> Replace turn signal lamp bulb. Refer to LT-64, "Bulb Replacement of Front Turn Signal Lamp" .
Revision: June 2006
LT-59
2007 Versa
LT
2. CHECK FRONT TURN SIGNAL LAMP CIRCUIT

1.
2.
3.

Disconnect BCM connector and front combination lamp LH or
RH connector.
Check continuity between BCM harness connector M20 (A) terminal 60 and front combination lamp LH harness connector E29
(B) terminal 4.
60 - 4
4.
Check continuity between BCM harness connector M20 terminal

61 (A) and front combination lamp RH harness connector E30
(B) terminal 4.
61 - 4
WKIA5612E
OK or NG
OK
>> GO TO 3.
NG
3. CHECK GROUND CIRCUIT

1.
Check continuity between front combination lamp LH harness

connector E29 terminal 5 and ground.
5 - Ground
2.
Check continuity between front combination lamp RH harness

connector E30 terminal 5 and ground.
5 - Ground
OK or NG
OK
>> Inspect connection at front combination lamp.
NG
>> Repair harness.
Rear Turn Signal Lamp Does Not Operate
WKIA5613E
EKS00IXC
1. CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-116, "Exterior Lamp" .
OK or NG
OK
>> GO TO 2.
NG
>> Replace turn signal lamp bulb. Refer to LT-64, "Bulb Replacement of Rear Turn Signal Lamp" .
Revision: June 2006
LT-60
2007 Versa
2. CHECK REAR TURN SIGNAL LAMP CIRCUIT

1.
2.
3.
60 - 6
4.

Disconnect BCM connector and rear combination lamp LH or
RH connector.
Check continuity between BCM harness connector M20 (A) terminal 60 and rear combination lamp LH harness connector B25
(B) terminal 6.
Check continuity between BCM harness connector M20 (A) terminal 61 and rear combination lamp RH harness connector
B107 (B) terminal 6.
61 - 6
WKIA5614E
OK or NG
OK
>> GO TO 3.
NG

1.
1 - Ground
2.
Check continuity between rear combination lamp LH harness

connector B25 terminal 1 and ground.
Check continuity between rear combination lamp RH harness

connector B107 terminal 1 and ground.
1 - Ground
OK or NG
OK
>> Check rear combination lamp connector for proper connection. Repair as necessary.
NG
J
WKIA5615E
LT
Revision: June 2006
LT-61
2007 Versa

Hazard Warning Lamp Does Not Operate But Turn Signal Lamp Operates
EKS00HYA
1. CHECK HAZARD SWITCH INPUT SIGNAL

With CONSULT-II
Select BCM on CONSULT-II. Select FLASHER on SELECT
TEST ITEM screen.
Make sure that HAZARD SW turns ON-OFF linked with operation of hazard switch.
1.
When hazard switch is in ON position
: HAZARD SW ON
PKIA7601E
Without CONSULT-II
Check voltage between BCM harness connector and ground.
Terminal
(+)
BCM
connector
Terminal
M18
29
Condition
()
Ground
Voltage
Hazard switch is ON
0V
Hazard switch is OFF
Battery voltage
OK or NG
OK
NG
>> GO TO 2.
PKIC1014E
2. CHECK HAZARD SWITCH CIRCUIT

1.
2.
3.

Disconnect BCM connector and hazard switch connector.
Check continuity BCM harness connector M18 (A) and hazard
switch harness connector M55 (B).
A
Continuity
Connector
Terminal
Connector
Terminal
M18
29
M55
Yes
OK or NG
OK
>> GO TO 3.
NG
Revision: June 2006
PKIC1015E
LT-62
2007 Versa
Check continuity between hazard switch harness connector M55 terminal 1 and ground.
1 Ground
OK or NG
OK
>> GO TO 4.
NG
D
PKIC1016E
4. CHECK HAZARD SWITCH

1.
2.
Disconnect hazard switch connector.

Check continuity hazard switch terminals.
Terminal
Hazard switch
1
Condition
Continuity
Hazard switch is ON
Yes
Hazard switch is OFF
No
OK or NG
OK
>> Replace BCM if hazard warning lamps do not operate
after setting the connector again. Refer to BCS-25,
"Removal and Installation of BCM" .
NG
>> Replace hazard switch.
Turn Signal Indicator Lamp Does Not Operate
H
PKIC1017E
EKS00J8H
1. CHECK CAN COMMUNICATION SYSTEM

Check CAN communication. Refer to LAN-44, "TROUBLE DIAGNOSIS" .
OK or NG
OK
>> Replace combination meter. Refer to DI-23, "Removal and Installation" .
NG
>> Repair as necessary.
LT
Revision: June 2006
LT-63
2007 Versa

Bulb Replacement of Front Turn Signal Lamp
EKS00HYB
Refer to LT-25, "Bulb Replacement" .
Bulb Replacement of Rear Turn Signal Lamp
EKS00HYC
Removal and Installation of Front Turn Signal Lamp
EKS00HYE
Refer to LT-25, "Removal and Installation" .
Removal and Installation of Rear Turn Signal Lamp
EKS00HYF
Revision: June 2006
LT-64
2007 Versa
LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCH
PFP:25540
A
EKS00HYH
REMOVAL
1.
2.
Remove steering column cover. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .

While pressing pawls (A) in direction as shown, pull lighting and
turn signal switch (1) toward LH door and disconnect from the
base.
E
PKIC1018E
INSTALLATION
F
LT
Revision: June 2006
LT-65
2007 Versa
HAZARD SWITCH
HAZARD SWITCH
PFP:25290
EKS00HYI
REMOVAL
1.
2.
3.
Remove cluster lid C. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .

Disconnect hazard switch connector.
Press pawl (A) on reverse side and remove the hazard switch
(1).
WKIA5421E
INSTALLATION
Revision: June 2006
LT-66
2007 Versa
COMBINATION SWITCH
COMBINATION SWITCH
Wiring Diagram COMBSW
PFP:25567
A
EKS00HYJ
LT
LKWA0333E
Revision: June 2006
LT-67
2007 Versa
COMBINATION SWITCH
Combination Switch Reading Function
EKS00HYK
For details, refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EKS00HYL
EKS00HYN
Combination Switch Inspection
EKS00HYO
1. SYSTEM CHECK
Referring to table below, check which system malfunctioning switch belongs to.
System 1
System 2
System 3
System 4
System 5
FRONT WASHER
FRONT WIPER LO
TURN LH
TURN RH
FRONT WIPER HI
FRONT WIPER INT
PASSING
HEAD LAMP 1
INT VOLUME 1
HEAD LAMP 2
HI BEAM
INT VOLUME 3
LIGHT SW 1ST
INT VOLUME 2
FRONT FOG
>> Check the system to which the switch belongs, and GO TO 2.
2. SYSTEM CHECK
With CONSULT-II
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Connect CONSULT-II, and select COMB SW on SELECT
TEST ITEM screen.
2. Select DATA MONITOR.
3. Select START, and confirm that other switches in the system
operate normally.
Example: When turn signal LH is inoperative, confirm that
PASSING, HEAD LAMP 2 or FRONT FOG (if equipped) turn
ON-OFF normally.
PKIA7602E
Without CONSULT-II
Operating combination switch, and confirm that other switches in the system operate normally.
Example: When a turn signal switch is inoperative, confirm that FRONT WIPER LO or FRONT WIPER INT
turn ON-OFF normally.
Check results
Other switches in the system operate normally.>>Replace lighting switch or wiper switch.
Other switches in the system do not operate normally.>>GO TO 3.
Revision: June 2006
LT-68
2007 Versa
COMBINATION SWITCH
3. HARNESS INSPECTION
1.
2.
3.
Suspect
system
A
Connector
M18
4.

Disconnect BCM connector and combination switch connector.
Check for continuity between BCM harness connector of the suspect system and the corresponding combination switch harness connector.
B
Terminal
Connector
Terminal
Input 1
Output 1
36
Input 2
Output 2
35
Input 3
10
Output 3
34
Input 4
Output 4
33
Input 5
Output 5
32
M28
Continuity
E
Yes
WKIA5497E
Check for continuity between of BCM harness connector in suspect system and ground.
Suspect
system
Connector
BCM
M18
Continuity
Terminal
Input 1
Output 1
36
Input 2
Output 2
35
Input 3
Output 3
34
Input 4
Output 4
33
Input 5
Output 5
32
J
Ground
No
WKIA5500E
OK or NG
OK
>> GO TO 4.
NG
>> Check harness between BCM and combination switch for open or short circuit.
Revision: June 2006
LT
LT-69
2007 Versa
COMBINATION SWITCH
4. CHECK BCM OUTPUT TERMINAL

1.
2.
3.
4.
5.
Connect BCM and combination switch connectors.

Turn ignition switch ON.
Turn lighting switch and wiper switch to OFF position.
Set wiper dial position 4.
Check BCM output terminal voltage waveform of suspect system.
Terminal
Suspect
system
(+)
Combination
switch
connector
Terminal
Reference value
()
PKIC1020E
PKIB4958J
M28
1.2V
Ground
PKIB8643J
1.2V
OK or NG
OK
>> Open circuit in combination switch, GO TO 5.
NG
5. COMBINATION SWITCH INSPECTION

Referring to table below, perform combination switch inspection.
Procedure
1
Replace
lighting
switch
2
Confirm
check
results
3
OK
INSPECTION END
NG
Replace wiper switch
4
Confirm
check
results
5
OK
INSPECTION END
NG
Replace switch base
6
Confirm
check
results
7
OK
INSPECTION END
NG
Confirm symptom again
>> INSPECTION END
EKS00HYP
Refer to LT-65, "LIGHTING AND TURN SIGNAL SWITCH" .
Revision: June 2006
LT-70
2007 Versa
STOP LAMP
STOP LAMP
Wiring Diagram STOP/L
PFP:26550
A
EKS00HYQ
LT
LKWA0334E
Revision: June 2006
LT-71
2007 Versa
STOP LAMP
Bulb Replacement of High-Mounted Stop Lamp
EKS00HYR
Refer to LT-72, "Removal and Installation of High-Mounted Stop Lamp" .
Bulb Replacement of Rear Combination Lamp for Stop Lamp
EKS00HYS
Removal and Installation of High-Mounted Stop Lamp
EKS00HYT
REMOVAL
1.
2.
3.
Remove rear hatch finish panel. Refer to EI-42, "LUGGAGE FLOOR TRIM" .
Disconnect the high-mounted stop lamp connector.
Remove nuts and remove high-mounted stop lamp from rear hatch.
INSTALLATION
CAUTION:
Properly seal the high-mounted stop lamp base to the rear hatch to prevent water leaks.
Removal and Installation of Rear Combination Lamp for Stop Lamp
EKS00HYU
Revision: June 2006
LT-72
2007 Versa
BACK-UP LAMP
BACK-UP LAMP
Wiring Diagram BACK/L
PFP:26550
A
EKS00HYV
LT
LKWA0335E
Revision: June 2006
LT-73
2007 Versa
BACK-UP LAMP
Bulb Replacement
EKS00HYW
EKS00HYX
Revision: June 2006
LT-74
2007 Versa
PARKING, LICENSE PLATE AND TAIL LAMPS

PFP:26550
A
EKS00HYY
D
WKIA5554E
1.
2.

box removed)
System Description

M28
EKS00HYZ
F
The control of the parking, license plate and tail lamp operation is dependent upon the position of lighting
switch. When the lighting switch is placed in the 1ST position, the BCM (body control module) receives input
signal requesting the parking, license plate and tail lamps to illuminate. This input signal is communicated to
the IPDM E/R (intelligent power distribution module engine room) via the CAN communication lines. The CPU G
(central processing unit) located in the IPDM E/R controls the tail lamp relay coil. This relay, when energized,
directs power to parking, license plate and tail lamps, which then illuminate.
H
to ignition relay located in IPDM E/R,
to tail lamp relay located in IPDM E/R,

I
to the CPU located in the IPDM E/R,

J
through 40A fusible link (letter g , located in fuse and fusible link block)
to BCM terminal 70,
through 10A fuse [No. 8, located in fuse block (J/B)],

LT
to BCM terminal 57.


L
to BCM terminal 38,
to ignition relay located in IPDM E/R and

M
through the ignition relay
to the CPU of the IPDM E/R.

to BCM terminal 11.

Ground is supplied
to BCM terminal 67
OPERATION BY LIGHTING SWITCH

With the lighting switch in the 1ST or 2ND position, the BCM receives an input signal requesting parking,
license plate and tail lamps to illuminate. This input signal is communicated to the IPDM E/R via the CAN communication lines. The CPU, located in the IPDM E/R, controls the tail lamp relay coil. When energized, the tail
lamp relay directs power
Revision: June 2006
LT-75
2007 Versa

through 10A fuse (No. 37, located in IPDM E/R),
to front combination lamp LH terminal 6, and
to front combination lamp RH terminal 6,
to rear combination lamp LH terminal 4 and
to license plate lamp LH and RH terminal 1,

Ground is supplied
to front combination lamp LH and RH terminal 7
to rear combination lamp LH terminal 1 and
to license plate lamp LH and RH terminal 2
through grounds B7 and B19, and

With power and ground supplied, parking, license plate and tail lamps illuminate.


When the combination switch (lighting switch) is in the 1ST (or 2ND) position and the ignition switch is turned
from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the parking, license and tail lamps remain illuminated for 5 minutes, then the parking,
license plate and tail lamps are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
EKS00HZ0
Revision: June 2006
LT-76
2007 Versa

Schematic
EKS00HZ2
LT
WKWA4975E
Revision: June 2006
LT-77
2007 Versa

Wiring Diagram TAIL/L
EKS00HZ3
LKWA0336E
Revision: June 2006
LT-78
2007 Versa

A
LT
LKWA0337E
Revision: June 2006
LT-79
2007 Versa
LKWA0338E
Revision: June 2006
LT-80
2007 Versa

EKS00HZ4
EKS00HZ5

1.
2.
3.
4.
5.
6.
EKS00HZ6

Do the parking, license plate and tail lamps operate normally? If YES, GO TO 6. If NO, GO TO 4.
Inspection End.
Preliminary Check
E
EKS00HZ7


G
EKS00HZ8

H
EKS00HZ9
Refer to LT-13, "CONSULT-II Function (IPDM E/R)" .
Parking, License Plate and Tail Lamps Do Not Illuminate
EKS00HZA
1. CHECK TAIL LAMP FUSE

J
Inspect tail lamp 10A fuse (No. 37, located in IPDM E/R).
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness.
LT

L
With CONSULT II
Make sure LIGHT SW 1ST turns ON-OFF linked with operation of lighting switch.
When lighting switch is 1ST
position
: LIGHT SW 1ST ON
Without CONSULT II
PKIA7607E
OK or NG
OK
>> GO TO 3.
NG
Revision: June 2006
LT-81
2007 Versa
3. ACTIVE TEST
With CONSULT-II
Select IPDM E/R on CONSULT-II, and select ACTIVE TEST
3. Touch TAIL on "ACTIVE TEST" screen.
4. Make sure parking, license plate and tail lamps operate.
1.
Parking, license plate and tail lamps should operate.

1.
2.
Without CONSULT-II
Make sure parking, license plate and tail lamps operate.
PKIC0936E
Parking, license plate and tail lamps should operate.

OK or NG
OK
>> GO TO 4.
NG
>> GO TO 5.
4. CHECK IPDM E/R

1.
2.
Select IPDM E/R on CONSULT-II, and select DATA MONITOR on SELECT DIAG MODE screen.
Make sure TAIL&CLR REQ turns ON when lighting switch is in
1ST position.
When lighting switch is 1ST
position
: TAIL&CLR REQ ON
OK or NG
OK
NG
Revision: June 2006
LT-82
SKIA5958E
2007 Versa
5. CHECK INPUT SIGNAL
1.
2.
3.
4.
5.
6.
With CONSULT-II
Disconnect front combination lamp, license plate lamp and rear combination lamp connectors.
Select IPDM E/R on CONSULT-II, and select ACTIVE TEST on SELECT DIAG MODE screen.
Touch TAIL on "ACTIVE TEST" screen.
When tail lamp relay is operating, check voltage between front combination lamp, license plate lamp and
rear combination lamp harness connector and ground.
1.
2.
3.
4.
Without CONSULT-II
Disconnect front combination lamp, license plate lamp and rear combination lamp connectors.
When tail lamp relay is operating, check voltage between front combination lamp, license plate lamp and
rear combination lamp harness connector and ground.
Terminal
(+)
()
Front combination lamp

connector
RH
E54
LH
E53
Voltage
Terminal
6
Ground
Battery voltage
I
WKIA5502E
Terminal
(+)
License plate lamp
connector
RH
B17
LH
B16
Terminal
1
()
Ground
Voltage
LT
Battery voltage
WKIA5503E
Terminal
(+)
Rear combination lamp
connector
(Tail lamp)
RH
B107
LH
B25
Voltage
Terminal
()
Ground
Battery voltage
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
Revision: June 2006
PKIC1118E
LT-83
2007 Versa
6. CHECK PARKING, LICENSE PLATE AND TAIL LAMP CIRCUIT

1.
2.
3.

front combination lamp harness connector (B).
A
Connector
B
Terminal
E45
Connector
Terminal
27
RH
E54
26
LH
E53
Continuity
Yes
WKIA5505E
4.

license plate lamp harness connector (B).
A
Connector
Terminal
E45
28
Connector
Terminal
RH
B17
LH
B16
Continuity
Yes
WKIA5506E
5.

rear combination lamp harness connector (B).
A
Connector
E45
B
Terminal
Connector
29
RH
B107
28
LH
B25
Terminal
4
Continuity
Yes
OK or NG
OK
NG
Revision: June 2006
LT-84
WKIA5508E
2007 Versa
7. CHECK PARKING, LICENSE PLATE AND TAIL LAMPS GROUND CIRCUIT

1.
Check continuity between front combination lamp harness connector and ground.
Front combination lamp connector

RH
E54
LH
E53
Terminal
7
Continuity
Ground
Yes
D
WKIA5509E
2.
Check continuity between license plate lamp harness connector

and ground.
License plate lamp
connector
RH
B17
LH
B16
Terminal
Continuity
Ground
2
Yes
WKIA5510E
3.
Check continuity between rear combination lamp harness connector and ground.
connector
RH
B107
LH
B25
Terminal
Continuity
Ground
Yes
OK or NG
OK
>> Check bulbs.
NG
LT
PKIC1029E
Parking, License Plate and Tail Lamps Do Not Turn OFF (After Approx. 10 Minutes)
EKS00HZB
This symptom is related to the ignition relay in IPDM E/R. Refer to PG-18, "Function of Detecting Ignition
Relay Malfunction" .
Select BCM on CONSULT-II. Select HEADLAMP on SELECT TEST ITEM screen and select DATA
MONITOR on SELECT DIAG MODE screen. If LIGHT SW 1ST is OFF when lighting switch is OFF,
replace IPDM E/R.
Revision: June 2006
LT-85
2007 Versa

Bulb Replacement
EKS00HZC
PARKING LAMP
LICENSE PLATE LAMP

1.
2.
3.
4.
Remove the license plate lamp. Refer to LT-86, "LICENSE PLATE LAMP" .
Remove bulb from the socket.
TAIL LAMP
EKS00HZD
PARKING LAMP
LICENSE PLATE LAMP
LKIA0759E
1.
License plate lamp
A.
Pawl
B.
Hook
Removal
1.
2.
Press the license plate lamp pawl on the side of the rear bumper fascia, then swing the license plate lamp
down to release the license plate lamp hook from the rear bumper fascia.
Disconnect the license plate lamp connector and remove the licence plate lamp.
Installation
TAIL LAMP
Revision: June 2006
LT-86
2007 Versa
REAR COMBINATION LAMP

Components
PFP:26554
A
EKS00IBB
I
LKIA0760E
1.
Rear combination lamp harness
2.
Turn signal lamp bulb
3.
Back-up lamp bulb
4.
Stop/tail lamp bulb
5.
Rear combination lamp housing

assembly
6.
Bumper stay
A.
Grommet
B.
Nut
C.
Clip
D.
Nuts
E.
Clip
Bulb Replacement
1.
2.
3.
LT
EKS00HZE
Remove the rear combination lamp. Refer to LT-87, "Removal and Installation" .
Remove bulb.
M
EKS00HZF
REMOVAL
1.
2.
3.
Remove rear combination lamp nuts.

Pull the rear combination lamp toward rear of the vehicle and remove from the vehicle.
Disconnect rear combination lamp connector, and remove rear combination lamp.
INSTALLATION
Disaassembly and Assembly
EKS00IBC
DISSASEMBLY
1.
2.
3.
Remove the rear combination lamp harness.

Remove the bulbs from the rear combination lamp housing assembly.
Revision: June 2006
LT-87
2007 Versa

ASSEMBLY
Revision: June 2006
LT-88
2007 Versa
INTERIOR LAMP
INTERIOR LAMP
Map lamp
PFP:28491
A
EKS00HZH
BULB REPLACEMENT
1.
2.
3.
Remove the map lamp lens (1).

Remove the bulb from lamp.
NOTE:
Pull bulb end from Y-shaped connector first to remove.
Install the map lamp lens (1) so the round lens is positioned to
the front of the vehicle as shown. There is a tab on the lens to
prevent incorrect installation of the lens.
LKIA0773E
REMOVAL AND INSTALLATION

Removal
1.
2.
Insert a suitable tool and disengage the pawl (A) fittings the map
lamp (1).
Disconnect map lamp connector and remove map lamp (1).
PKIC1038E
Installation
DISASSEMBLY AND ASSEMBLY

Disassembly
1.
2.
LT
Remove screw (A).

Remove sunroof switch (1).
PKIC1039E
Assembly
Revision: June 2006
LT-89
2007 Versa
INTERIOR LAMP
Luggage Compartment Lamp
EKS00HZI
BULB REPLACEMENT
LKIA0761E
1.
1.
2.
3.
Luggage compartment lamp bulb cover
2.
Luggage compartment lamp
A.
Tab A
Remove luggage compartment lamp cover.

Press tab A and remove the bulb.
REMOVAL AND INSTALLATION

Removal
1.
2.
Remove luggage compartment lamp from the luggage side finisher LH.
Disconnect luggage compartment lamp connector.
Installation
Revision: June 2006
LT-90
2007 Versa
INTERIOR ROOM LAMP

INTERIOR ROOM LAMP
PFP:26410
A
EKS00HZJ
G
WKIA5545E
1.
BCM M18, M19 and M20 (view with

glove box removed)
2.
Key switch and key lock solenoid

(without Intelligent Key) M27
3.
Key switch and ignition knob switch

(with Intelligent Key) M73
4.
Front door switch LH B8 and RH

B108
5.
Rear door switch LH B6 and RH

B116
6.
Front door key cylinder switch LH

D14
System Description
EKS00HZK
When room lamp switch is in DOOR position, room lamp ON/OFF is controlled by timer according to signals
from switches including key switch, front door switch LH, unlock signal from keyfob, door lock and unlock
switch, key cylinder lock and unlock switch, ignition switch.
J
When room lamp turns ON, there is a gradual brightening over 1 second.
When room lamp turns OFF, there is a gradual dimming over 1 second.
Interior room lamp timer is controlled by BCM (body control module).
LT
Interior room lamp timer control settings can be changed with CONSULT-II.
POWER SUPPLY AND GROUND

Power is supplied at all times (without Intelligent Key system)
to key switch and key lock solenoid terminal 2,
to BCM terminal 57,
to BCM terminal 70.

Power is supplied at all times (with Intelligent Key system)
to key switch and ignition knob switch terminals 2 and 4,
to BCM terminal 57,
to BCM terminal 70.

When key is inserted in the key switch and key lock solenoid, power is supplied (without Intelligent Key system)
through key switch and key lock solenoid terminal 1
to BCM terminal 37.

Revision: June 2006
LT-91
2007 Versa
INTERIOR ROOM LAMP

When key is inserted in the key switch and ignition knob switch, power is supplied (with Intelligent Key system)
through key switch and ignition knob switch terminal 1
to BCM terminal 37.

When ignition knob switch is pushed, power is supplied (with Intelligent Key system)
to Intelligent Key unit terminal 27.

to BCM terminal 38.

Ground is supplied
to BCM terminal 67

When front door LH is opened, ground is supplied
to BCM terminal 47
through front door switch LH terminal 2
through case ground of front door switch LH.

When front door RH is opened, ground is supplied
to BCM terminal 12
through front door switch RH terminal 2
through case ground of front door switch RH.

When rear door LH is opened, ground is supplied
to BCM terminal 48
through rear door switch LH terminal 1
through case ground of rear door switch LH.

When rear door RH is opened, ground is supplied
to BCM terminal 13
through rear door switch RH terminal 1
through case ground of rear door switch RH.

When back door is opened, ground is supplied
to BCM terminal 43
through back door lock assembly (back door switch) terminal 3
through back door lock assembly (back door switch) terminal 4

When front door LH is unlocked by front door key cylinder switch LH, the BCM receives a ground signal
to BCM terminal 7
through front door key cylinder switch LH terminal 3

When a signal, or combination of signals is received by BCM, ground is supplied
to room lamp terminal 2
through map lamp terminals 5 and 2 (with map lamp)
through BCM terminal 63.

With power and ground supplied, the interior room lamp illuminates.
SWITCH OPERATION
When map lamp switch is ON (with map lamp), ground is supplied
to map lamp terminal 1

Power is supplied
Revision: June 2006
LT-92
2007 Versa
INTERIOR ROOM LAMP

to map lamp terminal 4.

When interior room lamp switch is ON, ground is supplied
to interior room lamp terminal 1
through map lamp (with map lamp) terminal 7

Power is supplied
to room lamp terminal 3.
INTERIOR ROOM LAMP TIMER OPERATION

Without Intelligent Key System
When room lamp switch is in DOOR position, and when all conditions below are met, BCM performs timer F
control (maximum 30 seconds) for room lamp ON/OFF.
In addition, when the interior room lamp turns ON or OFF there is gradual brightening or dimming over 1 second.
G
Power is supplied
to key switch and key lock solenoid terminal 2.

H
When the key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM terminal 37.
When front door key cylinder switch LH is unlocked, ground is supplied
I
to BCM terminal 7

J

At the time that front door LH is opened, BCM detects that front door LH is unlocked. It determines that interior
room lamp timer operation condition is met, and turns the room lamp ON for 30 seconds.
LT
When key is in ignition key cylinder (key switch ON),
Power is supplied
through key switch and key lock solenoid terminal 1

L
to BCM terminal 37.

When key is removed from key switch and key lock solenoid (key switch OFF), the power supply to BCM terminal 37 is terminated. BCM detects that key has been removed, determines that interior room lamp timer
M
conditions are met, and turns the room lamp ON for 30 seconds.
When front door LH opens closes, and the key is not inserted in the key switch and key lock solenoid (key
switch OFF), voltage at BCM terminal 47 changes between 0V (door open) 12V (door closed). The BCM
determines that conditions for room lamp operation are met and turns the room lamp ON for 30 seconds.
Interior room lamp timer control is canceled under the following conditions:
Front door LH is locked (locked front door key cylinder switch LH).
Front door LH is opened (front door switch LH).
Ignition switch ON.
With Intelligent Key System

When the room lamp switch is in DOOR position, and when all conditions below are met, BCM performs timer
control (maximum 30 second) for room lamp ON/OFF.
In addition, when interior room lamp turns ON or OFF there is gradual brightening or dimming over 1 second.
Power is supplied
to key switch and ignition knob switch terminals 2 and 4.
Revision: June 2006
LT-93
2007 Versa
INTERIOR ROOM LAMP

When key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM terminal
37.
When the ignition knob switch is released, power will not be supplied to Intelligent Key unit terminal 27.
When front door key cylinder switch LH is unlocked, ground is supplied
to BCM terminal 7

At the time the front door LH is opened, the BCM detects the front door LH is unlocked. It determines that the
interior room lamp timer operation conditions are met, and interior room lamp ON for 30 seconds.
When the key is in ignition key cylinder (key switch ON), or ignition knob switch is pushed, power is supplied
to BCM terminal 37, or
to Intelligent Key unit terminal 27.

When the key is removed from key switch (key switch OFF), power supply to BCM terminal 37 is terminated.
When the ignition knob switch is released, power supply to intelligent key unit is terminated. The BCM detects
that the key has been removed, determines that interior room lamp timer conditions are met, and turns room
lamp ON for 30 seconds.
When the front door LH opens closes, and key is not inserted in key switch (or ignition knob switch is
released), BCM terminal 47 changes between 0V (door open) 12V (door closed). BCM determines that
conditions for room lamp operation are met, and turns room lamp ON for 30 seconds.
Interior room lamp timer control is canceled under the following conditions:
Front door LH is locked (with keyfob or front door key cylinder switch LH).
Front door LH is opened (front door switch LH).
Ignition switch ON.
INTERIOR LAMP BATTERY SAVER CONTROL

If an interior room lamp is left ON, it will not be turned OFF even when door is closed.
BCM turns off interior lamp automatically to save battery 30 minutes after ignition switch is turned off.
After lamps are turned OFF by the battery saver system, the lamps illuminate again when
front door key cylinder switch LH is locked or unlocked
door is opened or closed
key is removed from ignition key cylinder or inserted in ignition key cylinder, or the ignition knob switch is
pushed or released.
Interior lamp battery saver control time period can be changed by the function setting of CONSULT-II.
Revision: June 2006
LT-94
2007 Versa
INTERIOR ROOM LAMP

Schematic
EKS00HZL
LT
WKWA4976E
Revision: June 2006
LT-95
2007 Versa
INTERIOR ROOM LAMP

Wiring Diagram INT/L
EKS00HZM
LKWA0339E
Revision: June 2006
LT-96
2007 Versa
INTERIOR ROOM LAMP

A
LT
LKWA0340E
Revision: June 2006
LT-97
2007 Versa
INTERIOR ROOM LAMP
LKWA0341E
Revision: June 2006
LT-98
2007 Versa
INTERIOR ROOM LAMP

A
LT
LKWA0342E
Revision: June 2006
LT-99
2007 Versa
INTERIOR ROOM LAMP
LKWA0343E
Revision: June 2006
LT-100
2007 Versa
INTERIOR ROOM LAMP

EKS00HZN

1.
2.
3.
4.
5.
6.
EKS00HZO

Does the interior room lamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
Inspection End
Preliminary Check
D
EKS00HZP

E
EKS00HZQ
BCM diagnostic
test item
Diagnostic mode
Description
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
Inspection by part
Supports inspections and adjustments. Commands are transmitted to the BCM

for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
Displays BCM input/output data in real time.
SELF-DIAG RESULTS
ECU PART NUMBER
CONFIGURATION
Displays BCM self-diagnosis results.

BCM part number can be read.

Performs BCM configuration read/write functions.

LT
WORK SUPPORT
Display Item List
L
Item
Description
CONSULT-II
SET I/L DUNLCK INTCON
The 30 second operating function of the interior room lamps can be selected
when the front door LH is released (unlocked).
ON/OFF
ROOM LAMP ON TIME SET
The time in order to escalate illumination can be adjusted when interior room
lamps are turned on.
MODE 1 7
ROOM LAMP OFF TIME SET
The time in order to diminish illumination can be adjusted when interior room
lamps are turned off.
MODE 1 7
Reference between MODE and TIME for TURN ON/OFF

MODE
Time (sec.)
0.5
DATA MONITOR
Display Item List
Monitor item
Contents
IGN ON SW
ON/OFF
Displays IGN position (ON)/OFF, ACC position (OFF) judged from ignition switch signal.
KEY ON SW
ON/OFF
Displays Key inserted (ON)/key removed (OFF) status judged from key switch signal.
Revision: June 2006
LT-101
2007 Versa
INTERIOR ROOM LAMP

Monitor item
Contents
DOOR SW - DR
ON/OFF
Displays status of front door LH as judged from front door switch LH signal. (Door is
DOOR SW - AS
ON/OFF
Displays Door open (ON)/Door closed (OFF) status, determined from front door switch
RH signal.
DOOR SW - RR
ON/OFF
Displays Door open (ON)/Door closed (OFF) status, determined from rear door switch
RH signal.
DOOR SW - RL
ON/OFF
LH signal.
LOCK STATUS
ON/OFF
Display status (door is locked: ON/door is unlocked: OFF) of front door lock actuator LH
(unlock sensor) judged from the front door lock actuator LH (unlock sensor) signal.
CDL LOCK SW
ON/OFF
Displays Door locked (ON)/Door unlocked (OFF) status, determined from locking
detection switch in the front door LH.
CDL UNLOCK SW
ON/OFF
Displays Door unlocked (OFF) status, determined from locking detection switch in
front door RH.
I KEY LOCKNOTE
ON/OFF
Displays Locked (ON)/Other (OFF) status, determined from lock signal.
I KEY UNLOCKNOTE
ON/OFF
Displays Unlocked (ON)/Other (OFF) status, determined from unlock signal.
NOTE:
Vehicles without intelligent key system display this item, but cannot be monitored.
ACTIVE TEST
Display Item List
Test item
INT LAMP
Description
Interior room lamp can be operated by any ON-OFF operations.
WORK SUPPORT
Display Item List
Item
Description
CONSULT-II
ROOM LAMP TIMER SET
Interior room lamp battery saver timer setting can be changed.
ROOM LAMP BAT SAV SET
Interior room lamp battery saver control mode can be changed in this mode.
Select interior room lamp battery saver control mode between ON and OFF.
MODE 1: 30 min.
MODE 2: 60 min.
ON/OFF
DATA MONITOR
Display Item List
Monitor item
Contents
IGN ON SW
ON/OFF
Displays IGN position (ON)/OFF, ACC position (OFF) judged from ignition switch signal.
KEY ON SW
ON/OFF
Displays Key inserted (ON)/key removed (OFF) status judged from key switch signal.
DOOR SW - DR
ON/OFF
Displays status of front door LH as judged from front door switch LH signal. (Door is
DOOR SW - AS
ON/OFF
Displays Door open (ON)/Door closed (OFF) status, determined from front door switch
RH signal.
DOOR SW - RR
ON/OFF
RH signal.
DOOR SW - RL
ON/OFF
LH signal.
LOCK STATUS
ON/OFF
Display status (door is locked: ON/door is unlocked: OFF) of front door lock actuator LH
(unlock sensor) judged from the front door lock actuator LH (unlock sensor) signal.
CDL LOCK SW
ON/OFF
Displays Door locked (ON)/Door unlocked (OFF) status, determined from locking
detection switch in front door LH.
CDL UNLOCK SW
ON/OFF
Displays Door unlocked (OFF) status, determined from locking detection switch in passengers door.
Revision: June 2006
LT-102
2007 Versa
INTERIOR ROOM LAMP

Monitor item
Contents
I KEY LOCKNOTE
ON/OFF
Displays Locked (ON)/Other (OFF) status, determined from lock signal.
I KEY UNLOCKNOTE
ON/OFF
Displays Unlocked (ON)/Other (OFF) status, determined from unlock signal.
NOTE:
Vehicles without Intelligent Key system display this item, but cannot be monitored.
Interior Room Lamp Control Does Not Operate (With Map Lamp)
EKS00HZR
1. CHECK EACH SWITCH

Select "BCM" on CONSULT-II. With "INT LAMP" data monitor, make
sure switches listed in display item list turn ON-OFF linked with
switch operation. Refer to LT-101, "Display Item List" for switches
and their functions.
OK or NG
OK
>> GO TO 2.
NG
>> Inspect malfunctioning switch system.
PKIB0263E
2. ACTIVE TEST
1.
2.
Select BCM on CONSULT-II. Select INT LAMP" active test.

When room lamp switch is in DOOR position, make sure room
lamp operates.
Room lamp should operate.

OK or NG
OK
NG
>> GO TO 3.
LKIA0092E
LT
3. CHECK ROOM LAMP INPUT VOLTAGE

1.
2.

Check voltage between interior room lamp harness connector
R7 terminal 3 and ground.
3 - Ground
: Battery voltage.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 4.
WKIA5512E
Revision: June 2006
LT-103
2007 Versa
INTERIOR ROOM LAMP
4. CHECK MAP LAMP INPUT CIRCUIT

1.
2.
Map lamp switch is in OFF position.

Check voltage between map lamp harness connector R2 terminal 4 and ground.
4 - Ground
: Battery voltage.
OK or NG
OK
>> GO TO 5.
NG
WKIA5513E
5. CHECK ROOM LAMP INPUT CIRCUIT

1.
2.
Disconnect map lamp connector and interior room lamp connector.

Check continuity between map lamp harness connector R3 (A)
terminal 6 and interior room lamp harness connector R7 (B) terminal 3.
6-3
OK or NG
OK
>> Replace map lamp.
NG
WKIA5514E
6. CHECK ROOM LAMP

1.
2.
Disconnect interior room lamp connector.

Check continuity between interior room lamp terminals.
Terminal
Condition
Continuity
Interior room lamp
Room lamp switch is in DOOR

position
Yes
Room lamp switch is in OFF

position
No
OK or NG
OK
>> GO TO 7.
NG
>> Check bulb. If OK, replace interior room lamp.
WKIA5609E
7. CHECK MAP LAMP

1.
2.
Disconnect map lamp connectors.

Check continuity between map lamp terminals.
2-5
OK or NG
OK
>> GO TO 8.
NG
>> Replace map lamp.
WKIA5608E
Revision: June 2006
LT-104
2007 Versa
INTERIOR ROOM LAMP
8. CHECK CIRCUIT BETWEEN ROOM LAMP AND MAP LAMP
Check continuity between interior room lamp harness connector R7

(A) terminal 2 and map lamp harness connector R3 (B) terminal 5.
2-5
OK or NG
OK
>> GO TO 9.
NG
D
WKIA5556E
9. CHECK CIRCUIT BETWEEN MAP LAMP AND BCM

1.
2.
Disconnect BCM connector.

Check continuity between BCM harness connector M20 (A) terminal 63 and map lamp harness connector R2 (B) terminal 2.
63 - 2

G
OK or NG
OK
>> Replace BCM if room lamp does not work after setting
the connector again. Refer to BCS-25, "Removal and
Installation of BCM" .
NG
H
WKIA5518E
Interior Room Lamp Control Does Not Operate (Without Map Lamp)
EKS00IMK
1. CHECK EACH SWITCH

Select "BCM" on CONSULT-II. With "INT LAMP" data monitor, make
sure switches listed in display item list turn ON-OFF linked with
switch operation. Refer to LT-101, "Display Item List" for switches
and their functions.
OK or NG
OK
>> GO TO 2.
NG
>> Inspect malfunctioning switch system.
LT
PKIB0263E
2. ACTIVE TEST
1.
2.
Select "BCM" on CONSULT-II. Select "INT LAMP" active test.

When room lamp switch is in DOOR position, make sure room
lamp operates.
Room lamp should operate.
OK or NG
OK
NG
>> GO TO 3.
LKIA0092E
Revision: June 2006
LT-105
2007 Versa
INTERIOR ROOM LAMP
3. CHECK ROOM LAMP INPUT VOLTAGE

1.
2.

Check voltage between interior room lamp harness connector
R7 terminal 3 and ground.
3 - Ground
: Battery voltage should exist.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 6.
WKIA5610E
4. CHECK ROOM LAMP

1.
2.
Disconnect room lamp connector.

Check continuity between room lamp terminals.
Room lamp
Condition
Terminal
Continuity
Room lamp switch is in

DOOR position
Yes
Room lamp switch is in OFF

position
No
OK or NG
OK
>> GO TO 5.
NG
>> Check bulb. If OK, replace room lamp. Refer to LT-107, "ROOM LAMP" .
WKIA5609E
5. CHECK ROOM LAMP CIRCUIT

1.
2.
Disconnect BCM connector.

Check continuity between BCM harness connector M20 (A) terminal 56 and room lamp harness connector R7 (B) terminal 3.
56 - 3
OK or NG
OK
>> GO TO 6.
NG
WKIA5559E
6. CHECK ROOM LAMP CIRCUIT

1.
2.
Disconnect BCM connector and room lamp connector.

Check continuity between BCM harness connector M20 (A) terminal 63 and room lamp harness connector R7 (B) terminal 2.
63 - 2
OK or NG
OK
>> Replace BCM if interior lamp does not work after setting
the connector again. Refer to BCS-25, "Removal and
Installation of BCM" .
NG
WKIA5560E
Revision: June 2006
LT-106
2007 Versa
INTERIOR ROOM LAMP

Bulb Replacement
EKS00HZS
ROOM LAMP
1.
2.
3.
Remove lens (1) by inserting suitable tool and releasing LH

(switch side first).
Remove bulb (2).
NOTE:
Insert the lens hook end RH side first to install lens.
D
PKIC1048E
EKS00HZT
ROOM LAMP
Removal
1.
2.
Remove lens (1) and remove the room lamp by pulling down to
release the room lamp metal clips (A).
Disconnect connector and remove room lamp.
PKIC1049E
Installation
J
LT
Revision: June 2006
LT-107
2007 Versa
ILLUMINATION
ILLUMINATION
System Description
PFP:27545
EKS00HZU
The control of the illumination lamps operation is dependent upon the position of the lighting switch. When the
lighting switch is placed in the 1ST or 2ND position, the BCM (body control module) receives input signal
requesting the illumination lamps to illuminate. This input signal is communicated to IPDM E/R (intelligent
power distribution module engine room) across CAN communication lines. CPU (central processing unit)
located in the IPDM E/R controls the tail lamp relay coil. This relay, when energized, directs power to the illumination lamps, which then illuminate.
to ignition relay, located in IPDM E/R,
to tail lamp relay, located in IPDM E/R,
to BCM terminal 57.

to ignition relay, located in IPDM E/R, and
to BCM terminal 38.

to BCM terminal 11.

Ground is supplied
to BCM terminal 67
through grounds M57 and M61, and
ILLUMINATION OPERATION BY LIGHTING SWITCH

With the lighting switch in the 1ST or 2ND position, BCM receives input signal requesting the illumination
lamps to illuminate. This input signal is communicated to IPDM E/R across CAN communication lines. CPU
located in the IPDM E/R controls the tail lamp relay coil, which, when energized, directs power
to microphone terminal 3 (with Bluetooth)
to illumination control switch terminal 1
to glove box lamp terminal 1 (with glovebox lamp)
to audio unit terminal 9
to front air control terminal 5
to A/T device terminal 3 (without M/T)
to hazard switch terminal 3
to combination meter terminal 12
to door mirror remote control switch terminal 16, and
to main power window and door lock/unlock switch terminal 4.

Ground is supplied
to microphone terminal 2 (with Bluetooth)
to glove box lamp terminal 2 (with glove box lamp), and

Revision: June 2006
LT-108
2007 Versa
ILLUMINATION
to illumination control switch terminal 3

The illumination control switch controls illumination intensity by varying the ground to the following
through illumination control switch terminal 2
to audio unit terminal 8
to front air control terminal 6
to A/T device terminal 4 (without M/T)
to hazard switch terminal 4
to combination meter terminal 15,
to door mirror remote control switch,
to main power window and door lock/unlock switch terminal 10.

With power and ground supplied, illumination lamps illuminate.

EKS00HZV

G
LT
Revision: June 2006
LT-109
2007 Versa
ILLUMINATION
Schematic
EKS00HZX
WKWA4977E
Revision: June 2006
LT-110
2007 Versa
ILLUMINATION
Wiring Diagram ILL
EKS00HZY
LT
LKWA0344E
Revision: June 2006
LT-111
2007 Versa
ILLUMINATION
LKWA0345E
Revision: June 2006
LT-112
2007 Versa
ILLUMINATION
A
LT
LKWA0346E
Revision: June 2006
LT-113
2007 Versa
ILLUMINATION
LKWA0347E
Revision: June 2006
LT-114
2007 Versa
ILLUMINATION
Bulb Replacement
EKS00HZZ
GLOVE BOX LAMP
1.
2.
3.
Remove glove box assembly. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .

Turn bulb socket (1) counterclockwise and remove it.
Remove bulb (2).
PKIC1053E
LT
Revision: June 2006
LT-115
2007 Versa
BULB SPECIFICATIONS
BULB SPECIFICATIONS
Headlamp
PFP:26297
EKS00I00
Item
Wattage (W)
High/Low (Halogen type)
60/55 (H4)
Exterior Lamp
EKS00I01
Item
Front combination lamp
Wattage (W)
Turn signal lamp
21 (amber)
Parking (clearance) lamp

Stop/Tail lamp
5
21/5
Turn signal lamp
21 (amber)
Back-up lamp
21
Front fog lamp
35 (H8)
License plate lamp
High-mounted stop lamp
18
Interior Lamp/Illumination
EKS00I02
Item
Wattage (W)
Glove box lamp
1.4
Map lamp
Room lamp
Luggage compartment lamp
Revision: June 2006
LT-116
2007 Versa

LT89

Uploaded by

Copyright:

Available Formats

LT89

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LT89

Uploaded by

Copyright:

Available Formats

K ELECTRICAL

Revision: June 2006

Headlamp Low Beam Does Not Illuminate (One

Daytime Light Control Does Not Operate Properly

CONSULT-II Function (BCM) ..................................59

CONSULT-II Function (IPDM E/R) ......................... 81

Revision: June 2006

Revision: June 2006

HEADLAMP (FOR USA)

IPDM E/R E46, E47 and E48

Combination meter M24

BCM M18 and M20 (view with glove 3.

Combination switch (lighting switch)

to headlamp high relay RH and LH (located in IPDM E/R),

to headlamp low relay (located in IPDM E/R),

to ignition relay (located in IPDM E/R),

through 15A fuse (No. 52, located in IPDM E/R) and

through 20A fuse (No. 53, located in IPDM E/R)

to CPU located in IPDM E/R,

to BCM terminal 70,

through 10A fuse [No. 8, located in fuse block (J/B)]

to BCM terminal 57, and

through 10A fuse [No. 13, located in fuse block (J/B)]

to combination meter terminal 27.

to the ignition relay (located in IPDM E/R),

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 3, located in fuse block (J/B)]

to combination meter terminal 28.

HEADLAMP (FOR USA)

through 10A fuse [No. 20, located in fuse block (J/B)]

to BCM terminal 11.

to combination meter terminals 21, 22 and 23

through grounds M57 and M61, and

to IPDM E/R terminals 39 and 59

through grounds E15 and E24.

through 15A fuse (No. 41, located in IPDM E/R)

through IPDM E/R terminal 54

to headlamp RH terminal 3, and

through 15A fuse (No. 40, located in IPDM E/R)

through IPDM E/R terminal 52

to headlamp RH and LH terminals 2

through grounds E15 and E24.

High Beam Operation/Flash-to-Pass Operation

through 10A fuse (No. 34, located in IPDM E/R)

through IPDM E/R terminal 56

to headlamp RH terminal 1, and

through 10A fuse (No. 35, located in IPDM E/R)

through IPDM E/R terminal 55

to headlamp RH and LH terminal 2

through grounds E15 and E24.

COMBINATION SWITCH READING FUNCTION

EXTERIOR LAMP BATTERY SAVER CONTROL

CAN COMMUNICATION SYSTEM DESCRIPTION

Refer to LAN-4, "SYSTEM DESCRIPTION" .

HEADLAMP (FOR USA)

Revision: June 2006

HEADLAMP (FOR USA)

Revision: June 2006