Exterior Lighting System: Section

DRIVER CONTROLS
SECTION
EXTERIOR LIGHTING SYSTEM
EXL B
E
CONTENTS
BASIC INSPECTION .................................... 4 System Description ..................................................19 F
DIAGNOSIS AND REPAIR WORKFLOW .......... 4 DIAGNOSIS SYSTEM (BCM) ........................... 23

Work Flow ................................................................. 4 G
COMMON ITEM .........................................................23
FUNCTION DIAGNOSIS ............................... 7 COMMON ITEM : Diagnosis Description ................23
COMMON ITEM : CONSULT-III Function (BCM -
HEADLAMP (HALOGEN TYPE) ......................... 7 COMMON ITEM) .....................................................23 H
System Diagram ........................................................ 7
HEADLAMP ...............................................................24
System Description ................................................... 7
HEADLAMP : CONSULT-III Function (BCM -
Component Parts Location ........................................ 7 I
Component Description ............................................. 8 HEAD LAMP) ...........................................................24
FLASHER ...................................................................25
DAYTIME RUNNING LIGHT SYSTEM ............... 9
FLASHER : CONSULT-III Function (BCM - J
System Diagram ........................................................ 9
FLASHER) ...............................................................25
System Description ................................................... 9
Component Parts Location ...................................... 10 COMB SW ..................................................................26
Component Description ........................................... 10 COMB SW : CONSULT-III Function (BCM - K
COMB SW) ..............................................................26
AUTO LIGHT SYSTEM ......................................12
System Diagram ...................................................... 12 BATTERY SAVER .....................................................27
System Description ................................................. 12 BATTERY SAVER : CONSULT-III Function (BCM EXL
Component Parts Location ...................................... 13 - BATTERY SAVER) ...............................................27
Component Description ........................................... 13
DIAGNOSIS SYSTEM (IPDM E/R) ................... 29 M
TURN SIGNAL AND HAZARD WARNING Diagnosis Description ..............................................29
LAMPS ...............................................................15 CONSULT - III Function (IPDM E/R) .......................32
System Diagram ...................................................... 15
COMPONENT DIAGNOSIS ......................... 34 N
System Description ................................................. 15
Component Parts Location ...................................... 15
Component Description ........................................... 16
POWER SUPPLY AND GROUND CIRCUIT .... 34
BCM (BODY CONTROL MODULE) ..........................34 O
PARKING, LICENSE PLATE AND TAIL
BCM (BODY CONTROL MODULE) : Diagnosis
LAMPS ...............................................................17 Procedure ................................................................34
System Diagram ...................................................... 17 P
BCM (BODY CONTROL MODULE) : Special Re-
System Description ................................................. 17
pair Requirement .....................................................34
Component Parts Location ...................................... 17
Component Description ........................................... 18 IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) ..............................35
COMBINATION SWITCH READING SYSTEM IPDM E/R (INTELLIGENT POWER DISTRIBU-
....19 TION MODULE ENGINE ROOM) : Diagnosis Pro-
System Diagram ...................................................... 19 cedure ......................................................................35
Revision: September 2009 EXL-1 2010 Altima HEV

HEADLAMP (HI) CIRCUIT ................................ 36 STOP LAMP ..................................................... 128
Description .............................................................. 36 Wiring Diagram ..................................................... 128
Component Function Check ................................... 36
Diagnosis Procedure .............................................. 36 TURN SIGNAL AND HAZARD WARNING
LAMPS .............................................................. 132
HEADLAMP (LO) CIRCUIT ............................... 38 Wiring Diagram ..................................................... 132
Description .............................................................. 38
Component Function Check ................................... 38 SYMPTOM DIAGNOSIS ........................... 140
Diagnosis Procedure .............................................. 38
EXTERIOR LIGHTING SYSTEM SYMPTOMS.. 140
PARKING LAMP CIRCUIT ................................ 40 Symptom Table ..................................................... 140
Description .............................................................. 40
Component Function Check ................................... 40 BOTH SIDE HEADLAMPS DO NOT SWITCH
Diagnosis Procedure .............................................. 40 TO HIGH BEAM ................................................ 142
Description ............................................................ 142
TURN SIGNAL LAMP CIRCUIT ........................ 43 Diagnosis Procedure ............................................. 142
Description .............................................................. 43
Component Function Check ................................... 43 BOTH SIDE HEADLAMPS (LO) ARE NOT
Diagnosis Procedure .............................................. 43 TURNED ON ..................................................... 143
Description ............................................................ 143
OPTICAL SENSOR ........................................... 46 Diagnosis Procedure ............................................. 143
Description .............................................................. 46
Component Function Check ................................... 46 PARKING, LICENSE PLATE AND TAIL
Diagnosis Procedure .............................................. 46 LAMPS ARE NOT TURNED ON ...................... 144
Description ............................................................ 144
ECU DIAGNOSIS ........................................ 49 Diagnosis Procedure ............................................. 144
BCM (BODY CONTROL MODULE) .................. 49 NORMAL OPERATING CONDITION ............... 145
Reference Value ..................................................... 49 Description ............................................................ 145
Terminal Layout ...................................................... 53
Physical Values ...................................................... 53 PRECAUTION ........................................... 146
Wiring Diagram ....................................................... 70
Fail Safe ................................................................. 78 PRECAUTIONS ................................................ 146
DTC Inspection Priority Chart .............................. 79 Precaution for Supplemental Restraint System
DTC Index .............................................................. 80 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................... 146
IPDM E/R (INTELLIGENT POWER DISTRI- Precautions For High-Voltage System .................. 146
BUTION MODULE ENGINE ROOM) ................. 83 General precautions for service operations .......... 146
Reference Value ..................................................... 83
Terminal Layout ...................................................... 84 ON-VEHICLE MAINTENANCE ................. 147
Physical Values ...................................................... 84 HEADLAMP ...................................................... 147
Wiring Diagram ....................................................... 88
Aiming Adjustment ................................................ 147
Fail Safe ................................................................. 93
DTC Index .............................................................. 95 ON-VEHICLE REPAIR .............................. 149
WIRING DIAGRAM ..................................... 96 HEADLAMP ...................................................... 149
Bulb Replacement ................................................. 149
AUTO LIGHT SYSTEM ...................................... 96 Removal and Installation ....................................... 149
Wiring Diagram ....................................................... 96
Disassembly and Assembly .................................. 150
BACK-UP LAMP .............................................. 102 DAYTIME RUNNING LIGHT SYSTEM ............. 151
Wiring Diagram ......................................................102
Removal and Installation ....................................... 151
DAYTIME LIGHT SYSTEM .............................. 107 STOP LAMP ..................................................... 152
Wiring Diagram ......................................................107
HEADLAMP ..................................................... 115 Bulb Replacement ................................................. 152
Wiring Diagram ......................................................115 LICENSE PLATE LAMP ................................... 153
PARKING, LICENSE PLATE AND TAIL Bulb Replacement ................................................. 153
LAMPS ............................................................. 121 Removal and Installation ....................................... 153
Wiring Diagram ......................................................121
REAR COMBINATION LAMP .......................... 154 SERVICE DATA AND SPECIFICATIONS
Bulb Replacement ................................................. 154 (SDS) .......................................................... 158 A
SERVICE DATA AND SPECIFICATIONS
LIGHTING AND TURN SIGNAL SWITCH ....... 156 (SDS) ............................................................... 158 B
Removal and Installation ....................................... 156 Headlamp .............................................................. 158
HAZARD SWITCH ............................................ 157 Exterior Lamp ........................................................ 158
Removal and Installation ....................................... 157 C
EXL

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION
Work Flow INFOID:0000000005439227
OVERALL SEQUENCE
AWLIA1661GB

DETAILED FLOW A
1.INTERVIEW FOR MALFUNCTION
Find out what the customer's concerns are.
B
>> GO TO 2
2.SYMPTOM CHECK C
Verify the symptom from the customer's information.
D
>> GO TO 3
3.BASIC INSPECTION
Check the operation of each part. Check that any concerns occur other than those mentioned in the customer E
interview.
>> GO TO 4 F
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self diagnosis with CONSULT-III. Check that any DTC is detected.
G
Is any DTC detected?
YES >> GO TO 5
NO >> GO TO 6 H
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
I
>> GO TO 9
6.FAIL-SAFE ACTIVATION CHECK J
Determine if the customer's concern is related to fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7 K
NO >> GO TO 8
7.SYSTEM DIAGNOSIS EXL
Perform the system diagnosis for the system in which the fail-safe activates. Specify the malfunctioning part.
M
>> GO TO 9
8.SYMPTOM DIAGNOSIS
N
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9 O
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
P
>> GO TO 10
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self diagnosis with CONSULT-III. Verified that no DTCs are detected. Erase all DTCs detected
prior to the repair. Verify that DTC is not detected again.
Is any DTC detected?

YES >> GO TO 5
NO >> GO TO 11
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 3

HEADLAMP (HALOGEN TYPE)
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS A
System Diagram INFOID:0000000005439228
B
AWLIA0002GB
G
System Description INFOID:0000000005439229
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting H
and turn signal switch). When the combination switch (lighting and turn signal switch) is placed in the 2nd posi-
tion, the BCM (body control module) receives input requesting the headlamps and park lamps to illuminate.
This input is communicated to the IPDM E/R (intelligent power distribution module engine room) across the
CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls the headlamp high and I
headlamp low relay coils. When energized, these relays direct power to the respective headlamps, which then
illuminate.
Component Parts Location INFOID:0000000005439230
J
EXL
AWLIA0014ZZ

1. IPDM E/R E17, E18, E200 2. BCM M16, M17, M18, M19 (view with 3. Combination switch (lighting and turn
instrument panel removed) signal switch) M28
4. Combination meter M24
Component Description INFOID:0000000005439231
LOW BEAM OPERATION

When the combination switch (lighting and turn signal switch) is in 2ND position, the BCM receives input
requesting the headlamps to illuminate. This input is communicated to the IPDM E/R across the CAN commu-
nication lines. The CPU of the IPDM E/R controls the headlamp low relay coil which supplies power to the low
beam headlamps.
HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION
With the combination switch (lighting and turn signal switch) in the 2ND position and placed in HIGH position,
the BCM receives input requesting the headlamp high beams to illuminate. The flash to pass feature can be
used any time and also sends a signal to the BCM. This input is communicated to the IPDM E/R across the
CAN communication lines. The CPU of the combination meter controls the ON/OFF status off the HIGH BEAM
indicator. The CPU of the IPDM E/R controls the headlamp high relay coil which supplies power to the high
beam headlamps.
The combination meter receives a high beam request signal (ON) through the CAN communication lines and
turns the high beam indicator lamp ON.
COMBINATION SWITCH READING FUNCTION
Refer to EXL-19, "System Description".
AUTO LIGHT OPERATION

DAYTIME RUNNING LIGHT SYSTEM
A
AWLIA0010GB F
G
The headlamp system for Canada vehicles is equipped with a daytime light control unit that activates the high
beam headlamps at approximately half illumination whenever the hybrid system is operating. If the parking
brake is applied before the hybrid system is started the daytime lights will not be illuminated. The daytime H
lights will illuminate once the parking brake is released. Thereafter, the daytime lights will continue to operate
when the parking brake is applied.
EXL

AWNIA0931ZZ
⇐: Front
1. IPDM E/R E17, E18, E200, E201 2. Daytime light relay E3 (view with en- 3. BCM M16, M17, M18, M19 (view with
gine room in-line connectors discon- instrument panel removed)
nected and positioned aside)
4. Combination switch (lighting and turn 5. Combination meter M24 6. Parking brake switch E35
signal switch) M28
After starting the hybrid system with the parking brake released and the combination switch (lighting and turn
signal switch) in the OFF or 1ST position, the headlamp high beam automatically turns on. With the combina-

tion switch (lighting and turn signal switch) in the 2nd position or with autolamps ON, the headlamps function
the same as conventional light systems. A
OPERATION
The BCM monitors inputs from the parking brake switch and the combination switch (lighting and turn signal
switch) to determine when to activate the daytime light system. The BCM sends a daytime light request to the B
IPDM E/R via the CAN communication lines. The IPDM E/R grounds the daytime light relay which in turn, pro-
vides power to the ground side of the RH high beam lamp. Power flows backward through the RH high beam
lamp to the IPDM E/R, through the high beam fuses, through the LH high beam lamp circuit to the LH high C
beam lamp and on to ground. The high beam lamps are wired in series which causes them to illuminate at a
reduced intensity.
Engine With engine stopped With engine running D
Combination switch (lighting and OFF 1ST 2ND OFF 1ST 2ND
turn signal switch) Hi Lo P Hi Lo P Hi Lo P Hi Lo P Hi Lo P Hi Lo P
E
High beam – – – – – × × – × z* z* × z* z* × × – ×
Headlamp
Low beam – – – – – × × × × – – × – – × × × ×
Tail lamp – – – × × × × × × – – – × × × × × × F
License and instrument illumina-
– – – × × × × × × – – – × × × × × ×
tion lamp
• Hi: "HIGH BEAM" position G
• Lo: "LOW BEAM" position
• P: "FLASH TO PASS" position
• ×: Lamp "ON" H
• –: Lamp "OFF"
• z: Lamp dims. (Added functions)
• *: When starting the engine with the parking brake released, the daytime lights will operate. I
When starting the engine with the parking brake pulled, the daytime lights will not operate.
EXL

AUTO LIGHT SYSTEM
AUTO LIGHT SYSTEM
ABLIA2223GB
• BCM (Body Control Module) controls auto light operation according to signals from optical sensor, combina-
tion switch (lighting and turn signal switch) and ignition switch.
• IPDM E/R (Intelligent Power Distribution Module Engine Room) operates parking, side marker, license plate,
tail and headlamps according to CAN communication signals from BCM.
• Optical sensor detects ambient brightness of 800 to 2,500 lux. And optical sensor converts light (lux) to volt-
age, then sends the optical sensor signal to BCM.
OUTLINE
The auto light control system has an optical sensor that detects outside brightness.
When the combination switch (lighting and turn signal switch) is in AUTO position, it automatically turns ON/
OFF the parking, side marker, license plate, tail and headlamps in accordance with the ambient light. Sensitiv-
ity can be adjusted in four steps. For the details of the setting, Refer to BCS-22, "HEADLAMP : CONSULT-III
Function (BCM - HEAD LAMP)".

AUTO LIGHT SYSTEM
AWLIA0016ZZ
I
1. IPDM E/R E17, E18, E200 2. BCM M16, M17, M18, M19, M21 (view 3. Combination switch (lighting and turn
with instrument panel removed) signal switch) M28
4. Optical sensor M66 J
K
AUTO LIGHT OPERATION
Applicable lamps
• Low beam headlamp EXL
• Parking, license plate and tail lamps
• High beam headlamp (with the combination switch (lighting and turn signal switch) in HIGH BEAM position)
When the combination switch (lighting and turn signal switch) is in AUTO position with the ignition switch in
ON position, BCM detects the AUTO LIGHT (ON) by BCM combination switch reading function. BCM turns M
automatically ON/OFF the applicable lamps according to ambient brightness depending on the following con-
dition.
• It turns ON applicable lamps in 3 seconds when ambient brightness is less than 1250 lux. N
• The lighted lamps are turned OFF in 5 seconds when ambient brightness becomes 2500 lux or higher.
Releasing Function:
• Turn ignition switch to the OFF position, or O
• Change combination switch (lighting and turn signal switch) to the OFF, 1ST, 2ND position.
NOTE:
Timing for when lamps turn ON/OFF can be changed by the function setting of CONSULT-III. Refer to BCS-22, P
"HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)".
HEADLAMP LOW AND HIGH OPERATION
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
AUTO LIGHT SYSTEM

TURN SIGNAL AND HAZARD WARNING LAMPS
A
AWLIA0006GB F
G
• BCM (Body Control Module) controls turn signal lamp (RH and LH) and hazard warning lamp operation.
• Combination meter operates turn (RH and LH) indicator according to CAN communication signals from
BCM. H
EXL
P
AWLIA0018ZZ
1. BCM M16, M17, M18, M19 (view with 2. Combination switch (lighting and turn 3. Combination meter M24
4. Hazard switch M54

TURN SIGNAL OPERATION

When the combination switch (lighting and turn signal switch) is in LH or RH position with the ignition switch in
ON position, the BCM detects the TURN RH or TURN LH ON request. The BCM outputs the flasher output
signal to the respective turn signal lamp. The BCM sends a turn indicator signal ON request through the CAN
communication lines to the combination meter. The combination meter then activates the appropriate turn sig-
nal indicator and audible buzzer.
HAZARD LAMP OPERATION
When the hazard switch is in ON position, the BCM detects the hazard switch signal ON. The BCM outputs the
flasher output signal (right and left). The BCM sends a hazard indicator signal ON request through the CAN
communication lines to the combination meter. The combination meter then activates the hazard indicator and
audible buzzer.
REMOTE KEYLSESS ENTRY OPERATION
The remote keyless entry receiver transmits Intelligent Key signal to BCM, then BCM controls hazard lamps.
Refer to BCS-8, "System Description".

PARKING, LICENSE PLATE AND TAIL LAMPS
A
ABLIA2224GB F
G
• BCM (Body Control Module) controls parking, side marker, license plate and tail lamps operation.
• IPDM E/R (Intelligent Power Distribution Module Engine Room) operates parking, side marker, license plate
and tail lamps according to CAN communication signals from BCM. H
EXL
P
AWLIA0019ZZ
1. IPDM E/R E17, E18, E201 2. BCM M16, M17, M18, M19 (view with 3. Combination switch (lighting and turn

PARKING, LICENCE PLATE AND TAIL LAMPS OPERATION

When the combination switch (lighting and turn signal switch) is in 1ST position, BCM detects the COMBINA-
TION SWITCH (LIGHTING AND TURN SIGNAL SWITCH) 1ST POSITION ON. The BCM sends a parking
light ON request through the CAN communication lines to the IPDM E/R. The IPDM E/R then activates the tail
lamp relay which sends power to the parking and instrument illumination circuits.
EXTERIOR LAMP BATTERY SAVER CONTROL
With the combination switch (lighting and turn signal switch) in the 2nd position and the ignition switch is
turned from ON or ACC to OFF, the battery saver feature is activated.
Under this condition, the headlamps remain illuminated for 5 minutes unless the combination switch (lighting
and turn signal switch) position is changed. If the lighting switch position is changed, then the headlamps are
turned off.
This setting can be changed by CONSULT-III. Refer to EXL-27, "BATTERY SAVER : CONSULT-III Function
(BCM - BATTERY SAVER)".

COMBINATION SWITCH READING SYSTEM
A
JPMIA0083GB
G
OUTLINE H
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a I
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
J
Combination switch circuit
EXL
O
JPMIA0066GB
Combination switch INPUT-OUTPUT system list P

System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 — — HEADLAMP 2 HI BEAM

System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 4 — INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INPUT 5 INT VOLUME 2 — — — —
NOTE:
Headlamp has a dual system switch.

Description
• BCM reads the status of the combination switch at 10ms interval normally.
JPMIA0067GB
NOTE:
BCM reads the status of the combination switch at 60ms interval when BCM is controlled at low power con-
sumption mode.
• BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5→4→3→2→1.
- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
JPMIA0068GB
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.

Example 1: When a switch (TURN RH switch) is turned ON
• The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON. A
F
JPMIA0073GB
• BCM detects the combination switch status signal “1E” when the signal of OUTPUT 5 is input to INPUT 1.
• BCM judges that the TURN RH switch is ON when the signal “1E” is detected. G
Example 2: When some switches (TURN RH switch, FR WIPER LOW switch) are turned ON
• The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the
H
TURN RH switch and FR WIPER LOW switch are turned ON.
EXL
M
JPMIA0074GB
• BCM detects the combination switch status signal “1CE” when the signals of OUTPUT 3 and OUTPUT 5 are N
input to INPUT 1.
• BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal “1CE” is
detected. O
WIPER INTERMITTENT DIAL POSITION SETTING (FRONT WIPER INTERMITTENT OPERATION)
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2, and 3 switches.
P

Intermittent oper- INT VOLUME switch ON/OFF status

Wiper intermittent dial posi-
ation delay inter-
tion INT VOLUME 1 switch INT VOLUME 2 switch INT VOLUME 3 switch
val
1 ON ON ON
Short
2 ON ON OFF
3 ON OFF OFF
↑
4 OFF OFF OFF
↓
5 OFF OFF ON
6 OFF ON ON
Long
7 OFF ON OFF

DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : Diagnosis Description INFOID:0000000005804799
B
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
D
SELF-DIAGNOSTIC RESULT Displays the diagnosis results judged by BCM.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Read and save the vehicle specification. F
CONFIGURATION
• Write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
K
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
Air conditioner AIR CONDITONER × EXL
Intelligent Key system INTELLIGENT KEY × × ×
Combination switch COMB SW ×
BCM BCM × M
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
N
Trunk open TRUNK × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × O
Signal buffer system SIGNAL BUFFER × ×
TPMS AIR PRESSURE MONITOR × × ×
P
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000005804800
ECU IDENTIFICATION
Displays the BCM part No.
SELF-DIAG RESULT
Refer to BCS-68, "DTC Index".

HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000005804801
WORK SUPPORT
Work item Setting item Setting

1 Normal
MODE1
CUSTOM A/LIGHT MODE2 More sensitive setting than normal setting (Turns ON earlier than normal operation.)
SETTING2 MODE3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
ON1 With the exterior lamp battery saver function

BATTERY SAVER SET
OFF Without the exterior lamp battery saver function
MODE11 45 sec.
Without the func-
MODE2
tion
MODE3 30 sec.
2 MODE4 60 sec. Sets delay timer function timer operation time
ILL DELAY SET (All doors closed)
MODE5 90 sec.
MODE6 120 sec.
MODE7 150 sec.
MODE8 180 sec.
1 : Initial setting
2 : With auto light system
DATA MONITOR
Monitor item
Description
[Unit]
PUSH SW
The switch status input from push-button ignition switch
[ON/OFF]
ENGINE STATE
The engine status received from ECM with CAN communication
[STOP/STALL/CRANK/RUN]
VEH SPEED 1 The value of the vehicle speed received from combination meter with CAN commu-
[km/h] nication
KEY SW-SLOT
Key switch status input from key slot
[ON/OFF]

Monitor item
Description
[Unit] A
TURN SIGNAL R
[ON/OFF]
TURN SIGNAL L B
[ON/OFF]
TAIL LAMP SW
[ON/OFF] C
HI BEAM SW
[ON/OFF]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW 1 D
[ON/OFF]
HEAD LAMP SW 2
[ON/OFF] E
PASSING SW
[ON/OFF]
AUTO LIGHT SW1 F

[ON/OFF]
DOOR SW-DR
The switch status input from front door switch LH
[ON/OFF] G
DOOR SW-AS
The switch status input from front door switch RH
[ON/OFF]
DOOR SW-RR H
The switch status input from rear door switch RH
[ON/OFF]
DOOR SW-RL
The switch status input from rear door switch LH
[ON/OFF] I
OPTICAL SENSOR
The value of exterior brightness voltage input from the optical sensor
[V]1
1: With auto light system J
ACTIVE TEST
K
Test item Operation Description
Transmits the position light request signal to IPDM E/R with CAN com-
ON
TAIL LAMP munication to turn the tail lamp ON.
EXL
OFF Stops the tail lamp request signal transmission.
Transmits the high beam request signal with CAN communication to turn
HI
the headlamp (HI)
M
HEAD LAMP Transmits the low beam request signal with CAN communication to turn
LOW
the headlamp (LOW).
OFF Stops the high & low beam request signal transmission.
N
ON Transmits the daytime running light system request signal to IPDM E/R
DAYTIME RUNNING LIGHT1
OFF Stops the daytime running light request signal transmission
Transmits the delay timer function timer operation time signal to IPDM E/ O
ON
ILL DIM SIGNAL R with CAN communication to turn the headlamps ON (All doors closed).
OFF Stops the delay timer function timer signal transmission.
1: With daytime running light system. P
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000005804804
WORK SUPPORT

Service item Setting item Setting

LOCK ONLY Activated when locking.
Activated when unlock-
UNLOCK ONLY Sets the hazard warning lamp answer back activation
HAZARD ANSWER ing.
when the door is lock/unlock with the request switch or
BACK LOCK/UN- Activated when locking/ the key fob.
LOCK* unlocking
OFF Not activated
* : Initial setting
DATA MONITOR
Monitor item
Description
[Unit]
REQ SW-DR
The switch status input from request switch (driver side)
[ON/OFF]
REQ SW-AS
The switch status input from front request switch (passenger side)
[ON/OFF]
PUSH SW
[ON/OFF]
TURN SIGNAL R
[ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L
[ON/OFF]
HAZARD SW
The switch status input from the hazard warning switch
[ON/OFF]
RKE-LOCK
The lock signal status received from the keyless receiver
[ON/OFF]
RKE-UNLOCK
The unlock signal status received from the keyless receiver
[ON/OFF]
RKE-PANIC
The panic alarm signal status received from the keyless receiver
[ON/OFF]
ACTIVE TEST

OFF Turns turn signal lamps (right and left) OFF.
FLASHER LH Blinks left turn signal lamp.
RH Blinks right turn signal lamp.
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW) INFOID:0000000005804805
DATA MONITOR
Monitor item [UNIT] Description

FR WIPER HI Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
FR WIPER LOW Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
FR WASHER SW Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
FR WIPER INT Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination

Monitor item [UNIT] Description
A
FR WIPER STOP
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication.
[OFF/ON]
INT VOLUME Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
[1 - 7] function B
TURN SIGNAL R Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
TURN SIGNAL L Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch C
TAIL LAMP SW Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function. D
HI BEAM SW Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
HEAD LAMP SW 1 Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination E
HEAD LAMP SW 2 Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function. F
PASSING SW Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
AUTO LIGHT SW* Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination G
*: With auto light system
BATTERY SAVER H
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) INFOID:0000000005804806
I
WORK SUPPORT
Work item Setting item Setting J

ON* With the interior room lamp battery saver function
ROOM LAMP BAT SAV SET
OFF Without the interior room lamp battery saver function
MODE1* 30 min.
K
Sets the interior room lamp battery saver timer operating
ROOM LAMP TIMER SET
MODE2 60 min. time.
ON* With the exterior lamp battery saver function EXL

BATTERY SAVER SET
OFF Without the exterior lamp battery saver function
* : Initial setting
M
DATA MONITOR
Monitor item
Description N
[Unit]
REQ SW-DR
The switch status input from request switch (front LH)
[ON/OFF]
REQ SW-AS O
The switch status input from front request switch (front RH)
[ON/OFF]
PUSH SW
[ON/OFF] P
ACC RLY-F/B
Indicates [ON/OFF] condition of accessory relay.
[ON/OFF]
UNLK SEN-DR
Status of front door lock assembly LH (door unlock sensor)
[ON/OFF]
KEY SW-SLOT
Key switch status input from key slot
[ON/OFF]

Monitor item
Description
[Unit]
DOOR SW-DR
The switch status input from front door switch LH
[ON/OFF]
DOOR SW-AS
The switch status input from front door switch RH
[ON/OFF]
DOOR SW-RR
The switch status input from rear door switch RH
[ON/OFF]
DOOR SW-RL
The switch status input from rear door switch LH
[ON/OFF]
CDL LOCK SW
Lock switch status received from door lock/unlock switch by power window serial link
[ON/OFF]
CDL UNLOCK SW Unlock switch status received from door lock/unlock switch by power window serial
[ON/OFF] link
KEY CYL LK-SW
Lock switch status received from key cylinder switch by power window serial link
[ON/OFF]
KEY CYL UN-SW
Unlock switch status received from key cylinder switch by power window serial link
[ON/OFF]
TRNK/HAT MNTR
The switch status input from trunk room lamp switch
[ON/OFF]
RKE-LOCK
Lock signal status received from remote keyless entry receiver
[ON/OFF]
RKE-UNLOCK
Unlock signal status received from remote keyless entry receiver
[ON/OFF]
ACTIVE TEST

OFF Cuts the interior room lamp power supply to turn interior room lamp OFF.
BATTERY SAVER
ON Outputs the interior room lamp power supply to turn interior room lamp ON.*
* : Each lamp switch is in ON position.

DIAGNOSIS SYSTEM (IPDM E/R)
A
Diagnosis Description INFOID:0000000005804807
AUTO ACTIVE TEST B

Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp C
• Front wiper (LO, HI)
• Parking lamps
• Side marker lamps D
• License plate lamps
• Tail lamps
• Headlamps (LO, HI)
• Heater pump E
• Cooling fans
Operation Procedure
F
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield before hand. G
2. Turn ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the front door switch LH 10 times. Then turn the
ignition switch OFF. H
CAUTION:
Close front door RH.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test I
starts.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed. J
NOTE:
When auto active test mode has to be cancelled halfway through test, turn ignition switch OFF.
CAUTION: K
• If auto active test mode cannot be actuated, check door switch system. Refer to DLK-62,
"Component Function Check".
• Do not start the engine. EXL
Inspection in Auto Active Test Mode

When auto active test mode is actuated, the following 6 steps are repeated 3 times.
ALCIA0031ZZ
Operation
Inspection Location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• Side marker lamps
3 10 seconds
• Tail lamps
4 Headlamps LO ⇔ HI 5 times
5 Heater pump ON ⇔ OFF 5 times
6* Cooling fans MID for 5 seconds → HI for 5 seconds

*: Outputs duty ratio of 50% for 5 seconds → duty ratio of 100% for 5 seconds on the cooling fan control module.

Concept of auto active test
A
ABMIA1834GB F
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto G
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode H
Symptom Inspection contents Possible cause

YES BCM signal input circuit I
Any of the following components do not operate • Lamp or motor
• Parking lamps • Lamp or motor ground cir-
• Side marker lamps Perform auto active test. cuit
• License plate lamps Does the applicable system J
• Harness or connector be-
• Tail lamps operate? NO
tween IPDM E/R and appli-
• Headlamp (HI, LO) cable system
• Front wiper • IPDM E/R K
• Combination meter signal

input circuit
EXL
• CAN communication signal
between combination meter
YES
and ECM
Perform auto active test. • CAN communication signal M
Heater pump does not operate Does the heater pump oper- between ECM and IPDM E/
ate? R
• Heater pump
N
NO tween IPDM E/R and mag-
net clutch
• IPDM E/R O

Symptom Inspection contents Possible cause
tween IPDM E/R and oil
YES pressure switch
• Oil pressure switch
• IPDM E/R
Perform auto active test.
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal
lamp blink? between IPDM E/R and
BCM
NO • CAN communication signal
between BCM and combi-
nation meter
• Combination meter
• ECM signal input circuit
• CAN communication signal
YES
between ECM and IPDM E/
R
• Cooling fan
Perform auto active test. • Harness or connector be-
Cooling fan does not operate tween cooling fan and cool-
Does the cooling fan operate?
ing fan relays
NO • Cooling fan relays
tween IPDM E/R and cool-
ing fan relays
• IPDM E/R
CONSULT - III Function (IPDM E/R) INFOID:0000000005804808
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
Diagnosis mode Description

ECU Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
SELF DIAGNOSTIC
Refer to PCS-28, "DTC Index".
DATA MONITOR
Monitor item
Monitor Item MAIN SIG-

Description
[Unit] NALS
RADFAN REQ Displays the value of the cooling fan speed signal received from ECM via CAN
×
[%] communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN
×
[OFF/ON] communication.
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN
×
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN
×
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN
×
[STOP/1LOW/LOW/HI] communication.

Monitor Item MAIN SIG-
Description
[Unit] NALS A
WIP AUTO STOP
× Displays the status of the front wiper auto stop signal judged by IPDM E/R.
[STOP P/ACT P]
WIP PROT B
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[OFF/BLOCK]
IGN RLY1 -REQ Displays the status of the ignition switch ON signal received from BCM via CAN
[OFF/ON] communication. C
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R.
[OFF/ON]
PUSH SW D
Displays the status of the push-button ignition switch judged by IPDM E/R.
[OFF/ON]
DETENT SW Displays the status of the CVT shift selector (detention switch) judged by IPDM E/
[OFF/ON] R. E
DTRL REQ Displays the status of the daytime light request signal received from BCM via CAN
[OFF] communication.
OIL P SW F
Displays the status of the oil pressure switch judged by IPDM E/R.
[OPEN/CLOSE]
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM
[OFF/ON] via CAN communication.
G
HORN CHIRP Displays the status of the horn reminder signal received from BCM via CAN com-
[OFF/ON] munication.
ACTIVE TEST H
Test item
Test item Operation Description I

HORN ON Operates horn relay for 20 ms.
OFF OFF
J
FRONT WIPER LO Operates the front wiper relay.
HI Operates the front wiper relay and front wiper high relay.
1 OFF K
2 Outputs 50% pulse duty signal (PWM signal) to the cooling fan control module.
MOTOR FAN
EXL
OFF OFF
TAIL Operates the tail lamp relay. M
EXTERNAL LAMPS LO Operates the headlamp low relay.
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
HI
ond intervals. N

POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000005804809
Regarding Wiring Diagram information, refer to BCS-71, "Wiring Diagram".
1. CHECK FUSE AND FUSIBLE LINK

Check if the following BCM fuse or fusible link are blown.
Terminal No. Signal name Fuse and fusible link No.

1 J
Battery power supply
11 10
Is the fuse or fusible link blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M16 1
Battery voltage ALCIA0025ZZ
M17 11
Is the measurement normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M17 13 Yes
Does continuity exist?
YES >> Inspection End.
ALCIA0024ZZ
BCM (BODY CONTROL MODULE) : Special Repair Requirement INFOID:0000000005804810
1. REQUIRED WORK WHEN REPLACING BCM

Initialize control unit. Refer to CONSULT-III operation manual.

>> Work End.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) A
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-

agnosis Procedure INFOID:0000000005804811 B
Regarding Wiring Diagram information, refer to PCS-29, "Wiring Diagram". C
1. CHECK FUSES AND FUSIBLE LINK D

Check that the following IPDM E/R fuses or fusible link are not blown.
Terminal No. Signal name Fuses and fusible link No. E

1, 2 D, E, F
Battery power supply 42
— F
43
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit. G
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF. H
2. Disconnect IPDM E/R.
3. Check voltage between IPDM E/R harness connector and
ground. I
Terminals
(+) Voltage (V)
J
(−)
IPDM E/R (Approx.)
Connector Terminal
ALCIA0033ZZ
K
1 Ground
E16 Battery voltage
2
Is the measurement value normal? EXL
YES >> GO TO 3
3. CHECK GROUND CIRCUIT M
Check continuity between IPDM E/R harness connectors and

ground.
N
IPDM E/R
Continuity
Connector Terminal O
Ground
E18 (A) 12
Yes
E17 (B) 41
Does continuity exist? P
YES >> Inspection End. ALCIA0034ZZ

HEADLAMP (HI) CIRCUIT
Description INFOID:0000000005439265
The IPDM E/R (intelligent power distribution module engine room) controls the headlamp high relay based on
inputs from the BCM over the CAN communication lines. When the headlamp high relay is energized, power
flows through fuses 48 and 49, located in the IPDM E/R. Power then flows to the front combination lamps to
the headlamp high beam.
Component Function Check INFOID:0000000005439266
1.CHECK HEADLAMP (HI) OPERATION

WITHOUT CONSULT-III
1. Start IPDM E/R auto active test. Refer to PCS-13, "Diagnosis Description".
2. Check that the headlamp switches to the high beam.
NOTE:
HI/LO is repeated 1 second each when using the IPDM E/R auto active test.
CONSULT-III
1. Select "EXTERNAL LAMPS" of IPDM E/R active test item.
2. With operating the test items, check that the headlamp switches to the high beam.
HI : Headlamp switches to the high beam.

OFF : Headlamp OFF
Does the headlamp switch to the high beam?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-36, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000005439267
Regarding Wiring Diagram information, refer to EXL-115, "Wiring Diagram".
1.CHECK HEADLAMP (HI) FUSES

1. Turn the ignition switch OFF.
2. Check that the following fuses are not open.
Unit Location Fuse Capacity

Headlamp HI (LH) IPDM E/R 48 10A
Headlamp HI (RH) IPDM E/R 49 10A
Is the fuse open?
YES >> Repair the harness and replace the fuse.
NO >> GO TO 2
2.CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
2. Disconnect the front combination lamp connector.
3. Turn the ignition switch ON.

5. With EXTERNAL LAMPS ON, check the voltage between the
combination lamp connector and ground. A
Terminals
Condition
(+) (−) B
Voltage
Combination lamp External
Connector Terminal lamps
C
Ground Battery
RH E242 3 HI
voltage
ALLIA0116ZZ
LH E213 3 OFF 0V D
Is the measurement value normal?
YES >> GO TO 4
NO >> GO TO 3 E
3.CHECK HEADLAMP (HI) CIRCUIT FOR OPEN
2. Disconnect IPDM E/R connector. F
3. Check continuity between the IPDM E/R harness connector and
the front combination lamp harness connector.
G
A B
Continuity
Connector Terminal Connector Terminal
H
RH 89 E242 3
E200 Yes
LH 90 E213 3
Does continuity exist? I
YES >> GO TO 4 ALLIA0117ZZ
NO >> Repair the harnesses or connectors.
4.CHECK FRONT COMBINATION LAMP (HI) GROUND CIRCUIT J

2. Check continuity between the front combination lamp harness
connector terminal and ground. K
Front combination lamp

Continuity EXL
Connector Terminal
Ground
RH E242 4
Yes
LH E213 4 M
YES >> Inspect the headlamp bulb. ALLIA0118ZZ
NO >> Repair the harness. N

HEADLAMP (LO) CIRCUIT
The IPDM E/R (intelligent power distribution module engine room) controls the headlamp low relay based on
inputs from the BCM over the CAN communication lines. When the headlamp low relay is energized, power
flows through fuses 51 and 52, located in the IPDM E/R. Power then flows to the front combination lamps to
the headlamp low beam.
1.CHECK HEADLAMP (LO) OPERATION

WITHOUT CONSULT-III
1. Start IPDM E/R auto active test. Refer to PCS-13, "Diagnosis Description".
2. Check that the headlamp is turned ON.
NOTE:
HI/LO is repeated 1 second each when using the IPDM E/R auto active test.
CONSULT-III
2. With operating the test items, check that the headlamp is turned ON.
LO : Headlamp ON
OFF : Headlamp OFF
Is the headlamp turned ON?
YES >> Headlamp (LO) is normal.
1.CHECK HEADLAMP (LO) FUSES


Headlamp LO (LH) IPDM E/R 51 15A
Headlamp LO (RH) IPDM E/R 52 15A
Is the fuse open?
NO >> GO TO 2
2.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT-III

combination lamp connector and ground. A
Terminals
Condition
(+) (−) B
Voltage
Connector Terminal lamps
C
Ground Battery
RH E223 1 LO
voltage
ALLIA0119ZZ
LH E212 1 OFF 0V D
YES >> GO TO 4
NO >> GO TO 3 E
3.CHECK HEADLAMP (LO) CIRCUIT FOR OPEN
2. Disconnect IPDM E/R connector. F
the front combination lamp harness connector.
G
A B
Continuity
H
RH 83 E223 1
E200 Yes
LH 84 E212 1
Does continuity exist? I
YES >> GO TO 4 ALLIA0120ZZ
4.CHECK FRONT COMBINATION LAMP (LO) GROUND CIRCUIT J

2. Check continuity between the front combination lamp harness
connector terminal and ground. K

Continuity EXL
Connector Terminal
Ground
RH E223 2
Yes
LH E212 2 M
YES >> Inspect the headlamp bulb. ALLIA0121ZZ
NO >> Repair the harness. N

PARKING LAMP CIRCUIT
The IPDM E/R (intelligent power distribution module engine room) controls the tail lamp relay based on inputs
from the BCM over the CAN communication lines. When the tail lamp relay is energized, power flows through
fuses 46 and 47, located in the IPDM E/R. Power then flows to the front and rear combination lamps.
1.CHECK PARKING LAMP OPERATION

WITHOUT CONSULT-III
1. Activate IPDM E/R auto active test. Refer to PCS-13, "Diagnosis Description".
2. Check that the parking lamp is turned ON.
CONSULT-III
2. With operating the test items, check that the parking lamp is turned ON.
TAIL : Parking lamp ON

OFF : Parking lamp OFF
Is the parking lamp turned ON?
YES >> Parking lamp circuit is normal.
1.CHECK PARKING LAMP FUSES


Parking lamps (front) IPDM E/R 46 10A
Parking lamps (rear) IPDM E/R 47 10A
Is the fuse open?
NO >> GO TO 2
2.CHECK TAIL LAMP RELAY OUTPUT (VOLTAGE)
CONSULT-III

2. Disconnect the front combination lamp connector. A
B
combination lamp connector and ground.
Terminals
Condition C
(+) (−)
Voltage
Connector Terminal lamps D
Ground
Front A: E218, E225 8 LO Battery voltage
Rear B: B30, B45 2 OFF 0V
E
YES >> GO TO 4
NO >> GO TO 3
F
G
ALLIA0125ZZ
3.CHECK PARKING LAMP CIRCUIT (OPEN)

1. Turn the ignition switch OFF. H
2. Disconnect IPDM E/R connector.
the combination lamp harness connector. I
IPDM E/R Combination lamp

Continuity
Connector Terminal Connector Terminal J
Front A: E201 91, 92 B: E218, E225 8
Yes
Rear C: E18 7 D: B30, B45 2
K
YES >> GO TO 4
NO >> Repair the harnesses or connectors. EXL
ALLIA0126ZZ
4.CHECK PARKING LAMP GROUND CIRCUIT O

1. Disconnect the combination lamp connector.
2. Check continuity between the combination lamp harness con-
nector terminal and ground.
Combination lamp
Continuity
Connector Terminal
Ground
Front A: E218, E225 9
Yes
Rear B: B30, B45 5
YES >> Inspect the parking lamp bulb.
NO >> Repair the harness.
ALLIA0127ZZ

TURN SIGNAL LAMP CIRCUIT
A
The BCM monitors inputs from the combination switch to determine when to activate the turn signals. The B
BCM outputs voltage direction to the left and right turn signals during turn signal operation or both during haz-
ard warning operation. The BCM sends a turn signal indicator request to the combination meter via the CAN
communication lines.
The BCM performs the fast flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is C
open.
NOTE:
Turn signal lamp blinks at normal speed when using the hazard warning lamp. D
1.CHECK TURN SIGNAL LAMP E
CONSULT-III
1. Select "FLASHER" of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamp blinks. F
LH : Turn signal lamp LH blinking

RH : Turn signal lamp RH blinking G
OFF : The turn signal lamp OFF
Does the turn signal lamp blink? H
YES >> Turn signal lamp circuit is normal.
I
Regarding Wiring Diagram information, refer to EXL-132, "Wiring Diagram". J
1.CHECK TURN SIGNAL LAMP BULB K

Check the applicable lamp bulb to be sure the proper bulb standard is in use and the bulb is not open.
Is the bulb OK?
EXL
YES >> GO TO 2
NO >> Replace the bulb.
2.CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE M
2. Disconnect the front combination lamp connector or the rear combination lamp connector.
3. Turn the ignition switch ON. N
4. With operating the turn signal switch, check the voltage between
the BCM harness connector and the ground.
O
AWLIA0821ZZ

Terminals
Test item
(+) (−)
Voltage
BCM
FLASHER
Connector Terminal
Ground
RH M17 17 LH or RH
PKID0926E
LH M17 18 OFF 0V
YES >> GO TO 3
NO >> Replace BCM.
3.CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN
2. Disconnect BCM connector.
3. Check the continuity between the BCM harness connector and the front combination lamp, the rear com-
bination lamp harness connector or the door mirror connector (if equipped with turn signals in mirrors).

BCM Rear combination lamp
Door mirror Continuity

Rear LH B30 3
Front LH M17 18 E217 5
Door mirror LH D4 7 Yes
Rear RH B45 3
Front RH M17 17 E224 5
Door mirror RH D107 7
YES >> GO TO 4
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between the BCM harness connector and the
ground.
BCM
Continuity
Connector Terminal
Ground
LH 18
M17 No
RH 17
YES >> Repair the harnesses or connectors. ALLIA0129ZZ
NO >> GO TO 5
5.CHECK TURN SIGNAL LAMP GROUND CIRCUIT
Check continuity between the front combination lamp, the rear combination lamp or the door mirror and
ground (if equipped with turn signals in mirrors).

Front combination lamp A

Rear combination lamp
Door mirror Continuity
Connector Terminal B
Front RH E224 7
Front LH E217 7 Ground
C
Rear RH B45 5 Yes
Rear LH B30 5
Door mirror RH D107 8 D
Door mirror LH D4 8
YES >> Replace the front combination lamp or the rear combination lamp. E
EXL

OPTICAL SENSOR
OPTICAL SENSOR
The optical sensor converts the outside brightness (lux) to voltage and transmits the optical sensor signal to
the BCM.
1.CHECK OPTICAL SENSOR SIGNAL BY CONSULT-III

CONSULT-III
2. Select "OPTICAL SENSOR" of BCM (HEAD LAMP) DATA MONITOR item.
3. Turn the lighting switch to AUTO.
4. With the optical sensor illuminating, check the monitor status.
Monitor item Condition Voltage

When illuminating 3.1 V or more *
OPTICAL SENSOR
When shutting off light 0.6 V or less
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the item status normal?
YES >> Optical sensor is normal.
1.CHECK OPTICAL SENSOR POWER SUPPLY INPUT

2. Turn the lighting switch to AUTO.
3. Check the voltage between the optical sensor harness connec-
tor and ground.
Terminals
(+) (−)
Voltage
Optical sensor
M66 1 5V
Is the measurement value normal? ALLIA0130ZZ
YES >> GO TO 2
NO >> GO TO 4
2.CHECK OPTICAL SENSOR GROUND INPUT

OPTICAL SENSOR
Check the voltage between the optical sensor harness connector
and ground. A
Terminals
(+) (−) B
Voltage
Optical sensor
C
M66 3 Less than 0.2V
Is the measurement value normal? ALLIA0131ZZ
YES >> GO TO 3 D
NO >> GO TO 6
3.CHECK OPTICAL SENSOR SIGNAL OUTPUT
E
With the optical sensor illuminating, check voltage between the opti-
cal sensor harness connector and ground.
F
Terminals
Condition
(+) (−)
Voltage
Optical sensor G
Optical sensor
Connector Terminal
Ground
When illuminating 3.1V or more *
M66 2 H
When shutting off light 0.6V or less ALLIA0132ZZ
*: Illuminate the optical sensor. The value may be less than the standard if brightness
is weak.
I
YES >> GO TO 7
NO >> Replace the optical sensor.
J
4.CHECK OPTICAL SENSOR POWER SUPPLY FOR OPEN CIRCUIT
2. Disconnect the optical sensor connector and BCM connector. K
3. Check continuity between the optical sensor harness connector
and the BCM harness connector.
EXL
A B
Continuity
M66 1 M18 46 Yes M
YES >> GO TO 5
N
ALLIA0133ZZ
5.CHECK OPTICAL SENSOR POWER SUPPLY FOR SHORT CIRCUIT

O
Check the continuity between the optical sensor harness connector
and the ground.
P
Optical sensor
Continuity
M66 1 No
YES >> Repair the harnesses or connectors.
ALLIA0134ZZ

OPTICAL SENSOR
NO >> Replace BCM. Refer to BCS-83, "Removal and Installation" .
6.CHECK OPTICAL SENSOR GROUND FOR OPEN CIRCUIT
2. Disconnect the optical sensor connector and BCM connector.
A B
Continuity
M66 3 M18 45 Yes
YES >> Replace BCM. Refer to BCS-83, "Removal and Installa-
tion" .
ALLIA0135ZZ
7.CHECK OPTICAL SENSOR SIGNAL FOR OPEN CIRCUIT
2. Disconnect the optical sensor connector and BCM connector.
Optical sensor BCM

Continuity
M66 2 M18 21 Yes
YES >> GO TO 8
ALLIA0136ZZ
8.CHECK OPTICAL SENSOR SIGNAL FOR SHORT CIRCUIT

Check the continuity between the optical sensor harness connector
and the ground.
Optical sensor
Continuity
M66 2 No
YES >> Repair the harnesses or connectors.
NO >> Replace BCM. Refer to BCS-83, "Removal and Installa-
ALLIA0137ZZ
tion" .

< ECU DIAGNOSIS >
ECU DIAGNOSIS A
Reference Value INFOID:0000000005804751
B
VALUES ON THE DIAGNOSIS TOOL

C
Monitor Item Condition Value/Status
Other than front wiper switch HI OFF
FR WIPER HI
Front wiper switch HI ON D
Other than front wiper switch LO OFF
FR WIPER LOW
Front wiper switch LO ON
E
Front washer switch OFF OFF
FR WASHER SW
Front washer switch ON ON
Other than front wiper switch INT OFF F
FR WIPER INT
Front wiper switch INT ON
Front wiper is not in STOP position OFF
FR WIPER STOP G
Front wiper is in STOP position ON
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 Wiper intermittent dial position
Other than turn signal switch RH OFF H
TURN SIGNAL R
Turn signal switch RH ON
Other than turn signal switch LH OFF
TURN SIGNAL L
Turn signal switch LH ON I
Other than lighting switch 1ST and 2ND OFF
TAIL LAMP SW
Lighting switch 1ST or 2ND ON
J
Other than lighting switch HI OFF
HI BEAM SW
Lighting switch HI ON
Other than lighting switch 2ND OFF K
HEAD LAMP SW 1
Lighting switch 2ND ON
Other than lighting switch 2ND OFF
HEAD LAMP SW 2 EXL
Lighting switch 2ND ON
Other than lighting switch PASS OFF
PASSING SW
Lighting switch PASS ON M
Other than lighting switch AUTO OFF
AUTO LIGHT SW
Lighting switch AUTO ON
N
Front door LH closed OFF
DOOR SW-DR
Front door LH opened ON
Front door RH closed OFF O
DOOR SW-AS
Front door RH opened ON
Rear door RH closed OFF
DOOR SW-RR
Rear door RH opened ON P
Rear door LH closed OFF
DOOR SW-RL
Rear door LH opened ON
Other than power door lock switch LOCK OFF
CDL LOCK SW
Door lock/unlock switch LOCK ON

< ECU DIAGNOSIS >
Other than door lock/unlock switch UNLOCK OFF
CDL UNLOCK SW
Door lock/unlock switch UNLOCK ON
Other than front door LH key cylinder LOCK position OFF
KEY CYL LK-SW
Front door LH key cylinder LOCK position ON
Other than front door LH key cylinder UNLOCK position OFF
KEY CYL UN-SW
Front door LH key cylinder UNLOCK position ON
When hazard switch is not pressed OFF
HAZARD SW
When hazard switch is pressed ON
REAR DEF SW When rear window defogger switch is pressed ON
FAN ON SIG When AUTO switch or fan switch is pressed ON
AIR COND SW When A/C switch is pressed ON
Trunk lid opener cancel switch OFF OFF
TR CANCEL SW
Trunk lid opener cancel switch ON ON
Trunk lid opener switch OFF OFF
TR/BD OPEN SW
While the trunk lid opener switch is turned ON ON
Trunk lid closed OFF
TRNK/HAT MNTR
Trunk lid opened ON
When LOCK button of Intelligent Key is not pressed OFF
RKE-LOCK
When LOCK button of Intelligent Key is pressed ON
When UNLOCK button of Intelligent Key is not pressed OFF
RKE-UNLOCK
When UNLOCK button of Intelligent Key is pressed ON
When TRUNK OPEN button of Intelligent Key is not pressed OFF
RKE-TR/BD
When TRUNK OPEN button of Intelligent Key is pressed ON
When PANIC button of Intelligent Key is not pressed OFF
RKE-PANIC
When PANIC button of Intelligent Key is pressed ON
When UNLOCK button of Intelligent Key is not pressed and held OFF
RKE-P/W OPEN
When UNLOCK button of Intelligent Key is pressed and held ON
When LOCK/UNLOCK button of Intelligent Key is not pressed and
OFF
held simultaneously
RKE-MODE CHG
When LOCK/UNLOCK button of Intelligent Key is pressed and held
ON
simultaneously
When outside of the vehicle is bright Close to 5 V
OPTICAL SENSOR
When outside of the vehicle is dark Close to 0 V
When front door LH request switch is not pressed OFF
REQ SW-DR
When front door LH request switch is pressed ON
When front door RH request switch is not pressed OFF
REQ SW-AS
When front door RH request switch is pressed ON
When trunk request switch is not pressed OFF
REQ SW-BD/TR
When trunk request switch is pressed ON
When push-button ignition switch is not pressed OFF
PUSH SW
When push-button ignition switch is pressed ON
Ignition switch OFF or ACC OFF
IGN RLY -F/B
Ignition switch ON ON
Ignition switch OFF OFF
ACC RLY -F/B
Ignition switch ACC or ON ON

< ECU DIAGNOSIS >
A
When the brake pedal is not depressed ON
BRAKE SW 1
When the brake pedal is depressed OFF
When selector lever is in P position OFF B
DETE/CANCL SW
When selector lever is in any position other than P ON
When selector lever is in any position other than P or N OFF
SFT PN/N SW
When selector lever is in P or N position ON C
Front door LH UNLOCK status OFF
UNLK SEN-DR
Front door LH LOCK status ON
D
When push-button ignition switch is not pressed (IPDM E/R sends
OFF
via CAN)
PUSH SW -IPDM
When push-button ignition switch is pressed (IPDM E/R sends via E
ON
CAN)
IGN RLY1 F/B
Ignition switch ON ON F
When selector lever is in P position (IPDM E/R sends via CAN) OFF
DETE SW -IPDM When selector lever is in any position other than P (IPDM E/R sends
ON
via CAN) G
When selector lever is in any position other than P or N (IPDM E/R
OFF
SFT PN -IPDM sends via CAN)
When selector lever is in P or N position (IPDM E/R sends via CAN) ON H
When selector lever is in any position other than P (combination
OFF
meter sends via CAN)
SFT P -MET
When selector lever is in P position (combination meter sends via I
ON
CAN)
When selector lever is in any position other than N (combination
OFF
meter sends via CAN) J
SFT N -MET
When selector lever is in N position (combination meter sends via
ON
CAN)
Engine stopped STOP K
While the engine stalls STALL
ENGINE STATE
At engine cranking CRANK
EXL
Engine running RUN
VEH SPEED 1 While driving Equivalent to speedometer reading
VEH SPEED 2 While driving Equivalent to speedometer reading M
Front door LH LOCK status LOCK
DR DOOR STATE Wait with selective UNLOCK operation (5 seconds) READY
N
Front door LH UNLOCK status UNLK
Front door RH LOCK status LOCK
AS DOOR STATE Wait with selective UNLOCK operation (5 seconds) READY O
Front door RH UNLOCK status UNLK
Ignition switch ACC or ON RESET
ID OK FLAG P
Ignition switch OFF SET
When the hybrid system start is prohibited RESET
PRMT ENG STAT
When the hybrid system start is permitted SET
When Intelligent Key is not inserted into key slot OFF
KEY SW -SLOT
When Intelligent Key is inserted into key slot ON
RKE OPE COUN1 During the operation of Intelligent Key Operation frequency of Intelligent Key

< ECU DIAGNOSIS >
Ignition switch ON (only when the signal from the transmitter is re-
AIR PRESS FL Air pressure of front LH tire
ceived)
AIR PRESS FR Air pressure of front RH tire
ceived)
AIR PRESS RR Air pressure of rear RH tire
ceived)
AIR PRESS RL Air pressure of rear LH tire
ceived)
When ID of front LH tire transmitter is registered (refer to WT-6, "ID
DONE
Registration Procedure")
ID REGST FL1
When ID of front LH tire transmitter is not registered (refer to WT-6,
YET
"ID Registration Procedure")
When ID of front RH tire transmitter is registered (refer to WT-6, "ID
DONE
ID REGST FR1
When ID of front RH tire transmitter is not registered (refer to WT-6,
YET
When ID of rear RH tire transmitter is registered (refer to WT-6, "ID
DONE
ID REGST RR1
When ID of rear RH tire transmitter is not registered (refer to WT-6,
YET
When ID of rear LH tire transmitter is registered (refer to WT-6, "ID
DONE
ID REGST RL1
When ID of rear LH tire transmitter is not registered (refer to WT-6,
YET
Tire pressure indicator OFF OFF
WARNING LAMP
Tire pressure indicator ON ON
Tire pressure warning alarm is not sounding OFF
BUZZER
Tire pressure warning alarm is sounding ON

< ECU DIAGNOSIS >
Terminal Layout INFOID:0000000005804752
EXL
P
ALMIA0127ZZ
Physical Values INFOID:0000000005804753

< ECU DIAGNOSIS >
Terminal No. Description

(Wire color) Value
Input/ Condition
Signal name (Approx.)
(+) (-) Output
1
Ground Battery power supply Input Ignition switch OFF Battery voltage
(W/B)
2 Battery power supply
Ground Output Ignition switch OFF Battery voltage
(R/Y) output
3 Ignition power supply
Ground Output Ignition switch ON Battery voltage
(L/W) output
After passing the interior room lamp battery sav-
0V
4 Interior room lamp er operation time
Ground Output
(P/W) power supply Any other time after passing the interior room
Battery voltage
lamp battery saver operation time
UNLOCK (actuator is acti-
Battery voltage
5 Front door RH UN- vated)
Ground Output Front door RH
(G/Y) LOCK Other than UNLOCK (actu-
0V
ator is not activated)
7 ON Battery voltage
Ground Step lamp Output Room lamp timer
(R/W) OFF 0V
LOCK (actuator is activat-
Battery voltage
8 ed)
Ground All doors LOCK Output All doors
(V) Other than LOCK (actuator
0V
is not activated)
Battery voltage
9 Front door LH UN- vated)
Ground Output Front door LH
(G) LOCK Other than UNLOCK (actu-
0V
Rear door RH and Battery voltage
10 Rear door RH vated)
Ground rear door LH UN- Output
(G/Y) and rear door LH Other than UNLOCK (actu-
LOCK 0V
11
(Y/R)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position
Push-button ignition
14
Ground switch illumination Input Tail lamp
(R/Y) ON
ground
JSNIA0010GB
15 OFF Battery voltage

Ground ACC indicator lamp Output Ignition switch
(Y/L) ACC 0V

< ECU DIAGNOSIS >
(Wire color) Value A
Input/ Condition
(+) (-) Output
Turn signal switch OFF 0V
B
17
Ground Turn signal (RH) Output
Ignition switch C
(G/B) ON Turn signal switch RH
D
PKID0926E
6.5V
Turn signal switch OFF 0V
E
18 Ignition switch F
Ground Turn signal (LH) Output
(G/Y) ON Turn signal switch LH
G
PKID0926E
6.5V
19 Room lamp timer Interior room Lamps fully OFF Battery voltage
Ground Output H
(Y) control lamp Lamps fully ON 0V
When outside of the vehi-
Close to 5V
21 Ignition switch cle is bright I
Ground Optical sensor signal Input
(P/B) ON When outside of the vehi-
Close to 0V
cle is dark
24
Ground Stop lamp switch 1 Input — Battery voltage
J
(R/W)
OFF (brake pedal is not de-
0V
26 pressed)
Ground Stop lamp switch 2 Input Stop lamp switch K
(O/L) ON (brake pedal is de-
Battery voltage
pressed)
EXL
Front door lock as- LOCK status M

27
Ground sembly LH (unlock Input Front door LH
(G/W)
sensor)
JPMIA0011GB
N
11.8V
UNLOCK status 0V
29 When Intelligent Key is inserted into key slot Battery voltage O

Ground Key slot switch Input
(Y) When Intelligent Key is not inserted into key slot 0V
30 OFF 0
Ground ACC feedback signal Input Ignition switch P
(V/Y) ACC or ON Battery voltage
31 Ignition relay-2 feed- OFF 0V

Ground Input Ignition switch
(G) back signal ON Battery voltage

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output
OFF (when front door RH

32 Front door RH closes)
Ground Front door RH switch Input
(R/B) switch
JPMIA0011GB
11.8V
ON (when front door RH
0V
opens)
33 Compressor ON sig- OFF Battery voltage

Ground Input A/C switch
(SB) nal ON 0V
Front door lock as- Front door lock OFF (neutral) Battery voltage
34*
Ground sembly LH (key cylin- Input assembly LH (key
(L/R) ON (unlock) 0V
der switch) (unlock) cylinder switch)
36* Door lock/unlock Lock Battery Voltage

Ground Lock switch signal Input
(GR) switch Unlock 0V
37 Trunk lid opener can- Trunk lid opener CANCEL

Ground Input
(O) cel switch cancel switch
JPMIA0012GB
1.1V
ON 0V
38 Battery Voltage
Rear window defog- Rear window de- OFF
(GR/ Ground Input V
ger ON signal fogger switch
W) ON 0V
39* Unlock Battery Voltage
Door lock/unlock
(GR/ Ground Unlock switch signal Input
switch Lock 0V
R)
40* Power window serial Input/ Ignition switch ON

Ground
(Y/G) link Output
JPMIA0013GB
10.2V
Ignition switch OFF or ACC 0V
Engine switch ON 5.5V
41 Push-button ignition
Ground Output (push switch) illu-
(W) switch illumination OFF 0V
mination
42 LOCK indicator ON 0V
Ground LOCK indicator lamp Output
(R) lamp OFF Battery voltage
45 Receiver & sensor
Ground Input Ignition switch ON 0V
(P) ground

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
46 Receiver & sensor OFF 0V

(V/W)
Ground
power supply output
Output Ignition switch B
ACC or ON 5.0V
Standby state
D
OCC3881D
47 Tire pressure receiv- Input/ Ignition switch E

Ground
(G/O) er signal Output ON
F
When receiving the signal
from the transmitter
G
OCC3880D
48 Selector lever P/N P or N position 12.0V

Ground Input Selector lever H
(R/B) position signal Except P and N positions 0V
ON 0V
I
49 Security indicator sig- J

Ground Output Security indicator Blinking
(L/O) nal
JPMIA0014GB K
11.3V
OFF Battery voltage
All switch OFF 0V EXL
Lighting switch 1ST
Lighting switch high-beam
Combination M
50
Combination switch switch Lighting switch 2ND
(LG/ Ground Output
OUTPUT 5 (Wiper intermit-
B)
tent dial 4)
N
Turn signal switch RH
JPMIA0031GB
10.7V
O
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4) P
51 Combination switch Combination Any of the conditions below
Ground Output
(L/W) OUTPUT 1 switch with all switch OFF
• Wiper intermittent dial 1
• WIper intermittent dial 2
• Wiper intermittent dial 6 JPMIA0032GB
• Wiper intermittent dial 7 10.7V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output
All switch OFF
0V
Front washer switch ON
52 Combination switch Combination
Ground Output
(G/B) OUTPUT 2 switch Any of the conditions below
with all switch OFF
• WIper intermittent dial 5
• Wiper intermittent dial 6 JPMIA0033GB
10.7V
All switch OFF 0V
Front wiper switch INT
Front wiper switch LO
Combination
53
Combination switch switch
(LG/ Ground Output
OUTPUT 3 (Wiper intermit-
R)
tent dial 4)
Lighting switch AUTO
JPMIA0034GB
10.7V
All switch OFF 0V
Lighting switch flash-to-
pass
Combination
54 Combination switch switch
Ground Output
(G/Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH
JPMIA0035GB
10.7V
55 ON Battery voltage
Front blower mo-
(BR/ Ground Front blower monitor Input
tor switch OFF 0V
W)
Front door lock as- Front door lock OFF (neutral) Battery voltage
56
Ground sembly LH (key cylin- Input assembly LH (key
(L/B) ON (lock) 0V
der switch) (lock) cylinder switch)
57 Tire pressure warn-
Ground Input — Battery voltage
(W) ing check switch
OFF (front door LH

58 Front door LH CLOSE)
Ground Front door LH switch Input
(SB) switch
JPMIA0011GB
11.8V
ON (front door LH OPEN) 0V
59 Rear window defog- Rear window de- Active Battery voltage

Ground Output
(G/R) ger relay fogger Not activated 0V

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
When Intelligent Key is in

the passenger compart- C
ment
JMKIA0062GB
60 Front console anten- Ignition switch

D
Ground Output
(B/R) na 2 (-) OFF
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
When Intelligent Key is in H

the passenger compart-
ment
JMKIA0062GB
I
61 Center console an- Ignition switch
Ground Output
(W/R) tenna 2 (+) OFF
J

K
ment
JMKIA0063GB
EXL
M
the antenna detection area
N
When the front JMKIA0062GB
62 Front outside handle door RH request

Ground Output
(B/Y) RH antenna (-) switch is operat- O
ed with ignition
switch OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output

63 Front outside handle door RH request

Ground Output
(LG) RH antenna (+) switch is operat-
ed with ignition
switch OFF
area
JMKIA0063GB

64 Front outside handle door LH request

Ground Output
(V) LH antenna (-) switch is operat-
ed with ignition
switch OFF
area
JMKIA0063GB

65 Front outside handle door LH request

Ground Output
(P) LH antenna (+) switch is operat-
ed with ignition
switch OFF
area
JMKIA0063GB

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
Ignition switch is pressed Just after pressing ignition
68 NATS antenna amp Input/ B
Ground During waiting while inserting the Intelli- switch. Pointer of tester should
(G/O) (built in key slot) Output
gent Key into the key slot. move.
Ignition switch is pressed Just after pressing ignition
69 NATS antenna amp Input/
Ground During waiting while inserting the Intelli- switch. Pointer of tester should C
(O) (built in key slot) Output
gent Key into the key slot. move.
70 Ignition relay-2 con- OFF or ACC 0V

Ground Output Ignition switch
(R/B) trol ON Battery voltage D
During waiting
F
JMKIA0064GB
71 Remote keyless entry Input/

Ground
(L/O) receiver signal Output G
H
When operating either button on Intelligent Key
JMKIA0065GB I
All switch OFF

(Wiper intermittent dial 4) K
JPMIA0041GB
1.4V EXL
M
75 Combination switch Combination
Ground Input Wiper intermittent dial 4
(R/Y) INPUT 5 switch
N
JPMIA0037GB
1.3V
O
Any of the conditions below
with all switch OFF
• Wiper intermittent dial 1 P
JPMIA0040GB
1.3V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output
All switch OFF

JPMIA0041GB
1.4V
Lighting switch high-beam

JPMIA0036GB
76 Combination switch Combination 1.3V

Ground Input
(R/G) INPUT 3 switch
Lighting switch 2ND

JPMIA0037GB
1.3V

with all switch OFF
JPMIA0040GB
1.3V
78 Input/
Ground CAN-L — —
(P) Output
79 Input/
Ground CAN-H — —
(L) Output
OFF 0V
80 Key slot illumina-

Ground Key slot illumination Output Blinking
(R/L) tion
JPMIA0015GB
6.5V
ON Battery voltage
81 OFF or ACC Battery voltage

Ground ON indicator lamp Output Ignition switch
(LG) ON 0V

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
83 OFF 0V
(L)
Ground ACC relay control Output Ignition switch B
ACC or ON Battery voltage
84 CTV shift selector
Ground Output — Battery voltage
(Y/R) (detent switch)
C
87 CTV shift selector P position 0V
Ground Input Selector lever
(G/B) (detent switch) Any position other than P Battery voltage
ON (pressed) 0V D
E
88 Front door RH re- Front door RH re-
Ground Input
(P/L) quest switch quest switch OFF (not pressed)
F
JPMIA0016GB
1.0V
ON (pressed) 0V G
H
89 Front door LH re- Front door LH re-
Ground Input
(B/W) quest switch quest switch OFF (not pressed)
I
JPMIA0016GB
1.0V
OFF or ACC 0V J
90 Front blower motor
Ground Output Ignition switch
(Y) relay control ON Battery voltage
Remote keyless entry
91 K
Ground receiver power sup- Output Ignition switch OFF Battery voltage
(L/R)
ply
EXL

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output
All switch OFF
JPMIA0041GB
1.4V
Turn signal switch LH
JPMIA0037GB
1.3V
Combination
Ground Input Turn signal switch RH
(R/W) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
1.3V
Front wiper switch LO
JPMIA0038GB
1.3V
Front washer switch ON
JPMIA0039GB
1.3V

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
All switch OFF

(Wiper intermittent dial 4) C
JPMIA0041GB
1.4V D
E
Lighting switch AUTO
F
JPMIA0038GB
96 Combination switch Combination 1.3V

Ground Input G
(P/B) INPUT 4 switch
Lighting switch 1ST

H
JPMIA0036GB
I
1.3V
J
with all switch OFF
K
JPMIA0039GB
1.3V EXL

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output
All switch OFF
JPMIA0041GB
1.4V
Lighting switch flash-to-

pass
JPMIA0037GB
1.3V
Combination
Ground Input Lighting switch 2ND
(R/B) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
1.3V
Front wiper switch INT
JPMIA0038GB
1.3V
Front wiper switch HI
JPMIA0040GB
1.3V
Pressed 0V
98
Ground Hazard switch Input Hazard switch
(G/O) Not pressed
JPMIA0012GB
1.1V

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
Open (trunk lid opener ac-
Battery voltage B
103 tuator is activated)
Ground Trunk lid opening Output Trunk lid
(V) Close (trunk lid opener ac-
0V
tuator is not activated)
ON 0V C
110
Ground Trunk room lamp Output Trunk room lamp
(V/W) OFF Battery voltage

the passenger compart- E
ment
JMKIA0062GB
F
114 Trunk room antenna Ignition switch
Ground Output
(B) 1 (-) OFF
G
ment H
JMKIA0063GB
When Intelligent Key is in J

the passenger compart-
ment
K
JMKIA0062GB
115 Trunk room antenna Ignition switch

Ground Output
(W) 1 (+) OFF
EXL

in the passenger compart- M
ment
JMKIA0063GB
N

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
(+) (-) Output

When the trunk JMKIA0062GB
118 Rear bumper anten- lid request switch

Ground Output
(L/O) na (-) is operated with
ignition switch
OFF
area
JMKIA0063GB

When the trunk JMKIA0062GB

119
Rear bumper anten- lid request switch
(BR/ Ground Output
na (+) is operated with
W)
ignition switch
OFF
area
JMKIA0063GB
127 OFF or ACC Battery voltage

Ignition relay (IPDM
(BR/ Ground Output Ignition switch
E/R) control ON 0V
W)
130 Trunk room lamp Trunk room lamp OFF (trunk is closed)
Ground Input
(Y/G) switch switch
JPMIA0011GB
11.8V
ON (trunk is open) 0V
When selector lever is in P
or N position and the brake 0V
132 Ignition switch peddle is not depressed
Ground Start signal Output
(R) ON When selector lever is in P
or N position and the brake Battery voltage
peddle is depressed

< ECU DIAGNOSIS >
Input/ Condition
(+) (-) Output
140 Push-button ignition Engine switch Pressed 0V

(BR)
Ground
switch
Input
(push switch)
B
Not pressed Battery voltage
ON (pressed) 0V
141 Trunk request

Ground Trunk request switch Input D
(G/R) switch OFF (not pressed)
JPMIA0016GB E
1.0V
144 Request switch buzz- Request switch Sounding 0V

Ground Output
(GR) er buzzer Not sounding Battery voltage F
147 Trunk lid opener Trunk lid opener Pressed 0V
Ground Input
(L/R) switch switch Not pressed Battery voltage
G
H
OFF (when rear door RH
148 Rear door RH closes)
Ground Rear door RH switch Input
(R/W) switch
I
JPMIA0011GB
11.8V
ON (when rear door RH
0V J
opens)
K
OFF (when rear door LH
149 Rear door LH closes)
Ground Rear door LH switch Input EXL
(R/B) switch
JPMIA0011GB
11.8V
M
ON (when rear door LH
0V
opens)
*: With LH and RH front window anti-pinch system
N

< ECU DIAGNOSIS >
Wiring Diagram INFOID:0000000005804754
ABMWA0182GB

< ECU DIAGNOSIS >
EXL
ABMWA0183GB

< ECU DIAGNOSIS >
ALMWA0039GB

< ECU DIAGNOSIS >
EXL
ALMWA0040GB

< ECU DIAGNOSIS >
AAMWA0058GB

< ECU DIAGNOSIS >
EXL
AWMWA0192GB

< ECU DIAGNOSIS >
AWMIA0392GB

< ECU DIAGNOSIS >
EXL
ALMIA0084GB

< ECU DIAGNOSIS >
AWMIA0393GB
Fail Safe INFOID:0000000005804755
Display contents of CONSULT Fail-safe Cancellation

Inhibit hybrid system crank-
B2190: NATS ANTENNA AMP Erase DTC
ing
B2191: DIFFERENCE OF KEY Erase DTC
ing

< ECU DIAGNOSIS >
Display contents of CONSULT Fail-safe Cancellation
A
B2192: ID DISCORD BCM-ECM Erase DTC
ing
B2193: CHAIN OF BCM-ECM Erase DTC B
ing
B2195: ANTI-SCANNING Erase DTC
ing
Inhibit hybrid system crank- C
B2562: LOW VOLTAGE 100 ms after the power supply voltage increases to more than 8.8 V
ing
B2563: HI VOLTAGE 500 ms after the power supply voltage decreases to less than 18 V
ing D
500 ms after the following conditions are fulfilled
Inhibit hybrid system crank- • IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
B260A: IGNITION RELAY
ing • Ignition ON signal (CAN to IPDM E/R): OFF (Request signal) E
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
Maintains the power supply When any of the following conditions is fulfilled
B260F: ENG STATE SIG LOST position attained at the time • Power position changes to ACC
of DTC detection • Receives hybrid system status signal (CAN)
F
Inhibit hybrid system crank- 1 second after the starter motor relay control inside BCM becomes
B2617: STARTER RELAY CIRC
ing normal
G
Inhibit hybrid system crank- 1 second after the ignition relay (IPDM E/R) control inside BCM be-
B2618: BCM
ing comes normal
B261E: VEHICLE TYPE BCM initialization H
ing
When any of the following conditions is fulfilled
B26E1: ENG STATE NO RECIV • Power position changes to ACC
ing
• Receives hybrid system status signal (CAN) I
DTC Inspection Priority Chart INFOID:0000000005804756
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority J
chart.
Priority DTC K
• B2562: LOW VOLTAGE
1 • B2563: HI VOLTAGE
• B261E: VEHICLE TYPE EXL
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP M
• B2191: DIFFERENCE OF KEY
3 • B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING N

< ECU DIAGNOSIS >
Priority DTC
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: TRANSMISSION RANGE SWITCH
• B260A: IGNITION RELAY
• B260F: ENG STATE SIG LOST
• B2611: ACC RELAY
4
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E1: ENG STATE NO RECIV
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
5 • C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
• C1734: CONTROL UNIT
• B2622: INSIDE ANTENNA
6
• B2623: INSIDE ANTENNA
DTC Index INFOID:0000000005804757
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.

< ECU DIAGNOSIS >
Tire pressure A
Intelligent Key
CONSULT display Fail-safe monitor warning Reference page
warning lamp ON
lamp ON
No DTC is detected.
B
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT — — — BCS-36
C
U1010: CONTROL UNIT (CAN) — — — BCS-37
U0415: VEHICLE SPEED SIG — — — BCS-38
B2190: NATS ANTENNA AMP × — — SEC-30 D
B2191: DIFFERENCE OF KEY × — — SEC-33
B2192: ID DISCORD BCM-ECM × — — SEC-34
E
B2193: CHAIN OF BCM-ECM × — — SEC-35
B2195: ANTI SCANNING × — — SEC-36
B2553: IGNITION RELAY — — — PCS-50 F
B2555: STOP LAMP — — — SEC-37
B2556: PUSH-BTN IGN SW — × — SEC-40
B2557: VEHICLE SPEED × × — SEC-42 G
B2562: LOW VOLTAGE — — — BCS-39
B2563: HI VOLTAGE × × — BCS-40
H
B2601: SHIFT POSITION × × — SEC-43
B2602: SHIFT POSITION × × — SEC-46
B2603: SHIFT POSI STATUS × × — SEC-49 I
B2604: TRANSMISSION RANGE SWITCH × × — SEC-52
B260A: IGNITION RELAY × × — PCS-52
J
B260F: ENG STATE SIG LOST × × — SEC-54
B2611: ACC RELAY — — — PCS-53
B2614: ACC RELAY CIRC — × — PCS-55 K
B2615: BLOWER RELAY CIRC — × — PCS-58
B2616: IGN RELAY CIRC — × — PCS-61
EXL
B2617: STARTER RELAY CIRC × × — SEC-56
B2618: BCM × × — PCS-64
B261A: PUSH-BTN IGN SW — × — SEC-58 M
× (Turn ON for 15
B261E: VEHICLE TYPE × — SEC-60
seconds)
B2622: INSIDE ANTENNA — — — DLK-55 N
B2623: INSIDE ANTENNA — — — DLK-58
× (Turn ON for 15 SEC-55, "Descrip-
B26EA: KEY REGISTRATION × —
seconds) tion" O
C1704: LOW PRESSURE FL — — × WT-8
C1705: LOW PRESSURE FR — — × WT-8
P
C1706: LOW PRESSURE RR — — × WT-8
C1707: LOW PRESSURE RL — — × WT-8
C1708: [NO DATA] FL — — × WT-14
C1709: [NO DATA] FR — — × WT-14
C1710: [NO DATA] RR — — × WT-14
C1711: [NO DATA] RL — — × WT-14

< ECU DIAGNOSIS >
Tire pressure
Intelligent Key
CONSULT display Fail-safe monitor warning Reference page
warning lamp ON
lamp ON
C1712: [CHECKSUM ERR] FL — — × WT-16
C1713: [CHECKSUM ERR] FR — — × WT-16
C1714: [CHECKSUM ERR] RR — — × WT-16
C1715: [CHECKSUM ERR] RL — — × WT-16
C1716: [PRESSDATA ERR] FL — — × WT-18
C1717: [PRESSDATA ERR] FR — — × WT-18
C1718: [PRESSDATA ERR] RR — — × WT-18
C1719: [PRESSDATA ERR] RL — — × WT-18
C1720: [CODE ERR] FL — — × WT-16
C1721: [CODE ERR] FR — — × WT-16
C1722: [CODE ERR] RR — — × WT-16
C1723: [CODE ERR] RL — — × WT-16
C1724: [BATT VOLT LOW] FL — — × WT-16
C1725: [BATT VOLT LOW] FR — — × WT-16
C1726: [BATT VOLT LOW] RR — — × WT-16
C1727: [BATT VOLT LOW] RL — — × WT-16
C1729: VHCL SPEED SIG ERR — — × WT-19
C1734: CONTROL UNIT — — × WT-20

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
A
ROOM)
Reference Value INFOID:0000000005804762
B
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status C

Changes depending on engine
coolant temperature, air conditioner
RADFAN REQ Engine idle speed 0 - 100 %
operation status, vehicle speed, D
etc.
Lighting switch OFF OFF
TAIL&CLR REQ
Lighting switch 1ST, 2ND, HI or AUTO (Light is illuminated) ON E
HL LO REQ
Lighting switch 2ND HI or AUTO (Light is illuminated) ON
F
HL HI REQ
Lighting switch HI ON
Front wiper switch OFF STOP G
Front wiper switch INT 1LOW
FR WIP REQ Ignition switch ON
Front wiper switch LO LOW
H
Front wiper switch HI HI
Front wiper stop position STOP P
WIP AUTO STOP Ignition switch ON Any position other than front wiper
ACT P I
stop position
Front wiper operates normally OFF
WIP PROT Ignition switch ON Front wiper stops at fail-safe opera- J
BLOCK
tion
IGN RLY1 -REQ
Ignition switch ON ON K
IGN RLY
Ignition switch ON ON
EXL
Release the push-button ignition switch OFF
PUSH SW
Press the push-button ignition switch ON
• Press the selector button with M
CVT selector lever in P position
Ignition switch ON OFF
DETENT SW • CVT selector lever in any posi-
tion other than P
N
Release the CVT selector button with CVT selector lever in P position ON
DTRL OFF Off
DTRL REQ
DTRL ON On O
Ignition switch OFF, ACC or engine running OPEN
OIL P SW
Ignition switch ON CLOSE
Not operated OFF
P
THFT HRN REQ • Panic alarm is activated

• Horn is activated with VEHICLE SECURITY (THEFT WARNING) SYS- ON
TEM
Not operated OFF
HORN CHIRP
Door locking with Intelligent Key (horn chirp mode) ON

< ECU DIAGNOSIS >
Terminal Layout INFOID:0000000005804763
TERMINAL LAYOUT
ALMIA0128ZZ
Physical Values INFOID:0000000005804764
PHYSICAL VALUES

(Wire color) Value
Input/ Condition
+ − Output
1
(R)
2
(L)
4 Ignition Front wiper switch OFF 0V

Ground Front wiper LO Output
(LG) switch ON Front wiper switch LO Battery voltage
5 Ignition Front wiper switch OFF 0V

Ground Front wiper HI Output
(Y) switch ON Front wiper switch HI Battery voltage
Daytime light relay power
6
Ground supply (Canada models Output Ignition switch OFF Battery voltage
(SB)
only)
7 Tail, license plate lamps & Ignition Lighting switch OFF 0V

Ground Output
(GR) interior lamps switch ON Lighting switch 1ST Battery voltage

< ECU DIAGNOSIS >
Input/ Condition
+ − Output
Ignition switch OFF
(For a few seconds after turning ignition 0V B
switch OFF)
10
Ground ECM relay power supply Output • Ignition switch ON
(BR)
• Ignition switch OFF C
Battery voltage
(More than a few seconds after turn-
ing ignition switch OFF)
12 D
(B)
Approximately 1 second or more after
0V
turning the ignition switch ON
13 E
Ground Fuel pump power supply Output • Approximately 1 second after turning
(SB)
the ignition switch ON Battery voltage
• Engine running
Ignition switch OFF 0V
F
15 Ignition relay-1 power sup-
Ground Output
(V) ply Ignition switch ON Battery voltage
Front wiper stop position 0V
16 Ignition G
Ground Front wiper auto stop Input Any position other than
(L/Y) switch ON Battery voltage
front wiper stop position
19 Ignition relay-1 power sup- Ignition switch OFF 0V H

Ground Output
(Y) ply Ignition switch ON Battery voltage
20
Ground Ambient sensor ground — Ignition switch ON 0V
(L) I
21
Ground Ambient sensor — Ignition switch ON 5V
(LG)
22 Refrigerant pressure sen- J
Ground — Ignition switch ON 0V
(W/R) sor ground
• Ignition switch ON (READY)
23 Refrigerant pressure sen- • Both A/C switch and blower motor K
Ground — 1.0 - 4.0V
(B/R) sor switch ON (electric compressor oper-
ates)
24 Refrigerant pressure sen-
Ground — Ignition switch ON 5V EXL
(BR/W) sor power supply
25 Ignition relay-1 power sup- Ignition switch OFF 0V

Ground Output
(R) ply Ignition switch ON Battery voltage M
27 Ignition switch OFF or ACC Battery voltage
Ground Ignition relay monitor Input
(W) Ignition switch ON 0V
Press the push-button ignition switch 0V N
28 Push-button ignition
Ground Input
(SB) switch Release the push-button ignition switch Battery voltage
31 Ignition switch OFF 0V

Ground Ignition relay power supply Output O
(B) Ignition switch ON Battery voltage
39 Input/
— CAN-L — —
(P) Output P
40 Input/
— CAN-H — —
(L) Output
41
(B)
42 Ignition switch OFF or ACC 0V

Ground Cooling fan relay-1 control Input
(SB) Ignition switch ON 0.7V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ − Output
Press the CVT selector
button (CVT selector lever Battery voltage
P)
43 CVT shift selector Ignition • CVT selector lever in

Ground Input any position other than
(G/B) (Detention switch) switch ON
P
0V
• Release the CVT selec-
tor button (CVT selector
lever P)
44 The horn is deactivated Battery voltage

Ground Horn relay control Input
(G/W) The horn is activated 0V
45 The horn is deactivated Battery voltage

Ground Anti theft horn relay control Input
(L/O) The horn is activated 0V
Heater pump OFF 0V
48 Heater pump relay power Engine
Ground Output Heater pump ON
(R) supply running Battery voltage
(Heater pump is operating)
Ignition switch OFF
(For a few seconds after turning ignition 0V
switch OFF)
49
(v)
• Ignition switch OFF
Battery voltage

Ground Ignition relay power supply Output
(SB) Ignition switch ON Battery voltage
Ignition switch OFF
switch OFF)
53
(V)
Battery voltage
Ignition switch OFF
switch OFF)
54 Throttle control motor re-
Ground Output • Ignition switch ON
(GR) lay power supply
Battery voltage
55
Ground ECM power supply Output Ignition switch OFF Battery voltage
(LG)

(R) Ignition switch ON Battery voltage

(O) Ignition switch ON Battery voltage
Ignition switch OFF
(For a few seconds after turning ignition Battery voltage
switch OFF)
69
Ground ECM relay control Output • Ignition switch ON
(SB)
0 - 1.5V

< ECU DIAGNOSIS >
Input/ Condition
+ − Output
0 -1.0V
↓ B
70 Throttle control motor re- Ignition switch ON → OFF Battery voltage
Ground Output ↓
(G) lay control
0V
C
Ignition switch ON 0 - 1.0V
75 Ignition Engine stopped 0V

Ground Oil pressure switch Input
(LG) switch ON Engine running Battery voltage D
• Approximately 1 second after turning
the ignition switch ON 0 - 1.0V
77 • Engine running
Ground Fuel pump relay control Output E
(GR)
Approximately 1 second or more after
Battery voltage
turning the ignition switch ON
83 Ignition Lighting switch OFF 0V F

Ground Headlamp LO (RH) Output
(R/Y) switch ON Lighting switch 2ND Battery voltage
84 Ignition Lighting switch OFF 0V

Ground Headlamp LO (LH) Output G
(L) switch ON Lighting switch 2ND Battery voltage
88 Washer pump power sup-
Ground Output Ignition switch ON Battery voltage
(R/W) ply
H
• Lighting switch HI
89 Ignition Battery voltage
Ground Headlamp HI (RH) Output • Lighting switch PASS
(L/W) switch ON
Lighting switch OFF 0V
I
• Lighting switch HI
90 Ignition Battery voltage
Ground Headlamp HI (LH) Output • Lighting switch PASS
(G) switch ON
Lighting switch OFF 0V J
91 Ignition Lighting switch 1ST Battery voltage
Ground Parking lamp (RH) Output
(LG/R) switch ON Lighting switch OFF 0V
Lighting switch 1ST Battery voltage K
92 Ignition
Ground Parking lamp (LH) Output
(LG/B) switch ON Lighting switch OFF 0V
97
(V)
Ground Cooling fan control Output Engine idling 0-5V EXL
99
Ground Ambient sensor ground — Ignition switch ON 0V
(BR/W)
M
100
Ground Ambient sensor — Ignition switch ON 5V
(SB)
Ground — Ignition switch ON 0V N
(W) sor ground
• Ignition switch ON (READY)
102 Refrigerant pressure sen- • Both A/C switch and blower motor
Ground — 1.0 - 4.0V
(R) sor switch ON (electric compressor oper- O
ates)
Ground — Ignition switch ON 5V
(P) sor power supply P
Ignition Daytime light system ac-
Battery voltage
105 Daytime light relay control switch ON tive
Ground Output
(V) (Canada only) Ignition Daytime light system inac-
0V
switch ON tive

< ECU DIAGNOSIS >
ABMWA0191GB

< ECU DIAGNOSIS >
EXL
ABMWA0192GB

< ECU DIAGNOSIS >
ALMWA0033GB

< ECU DIAGNOSIS >
EXL
ABMIA0566GB

< ECU DIAGNOSIS >
ALMIA0077GB

< ECU DIAGNOSIS >
EXL
ALMIA0078GB
Fail Safe INFOID:0000000005804766 P
CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With ECM

< ECU DIAGNOSIS >
Control part Fail-safe in operation

• Signals cooling fans ON when the ignition switch is turned ON
Cooling fan
• Signals cooling fans OFF when the ignition switch is turned OFF
Heater pump Heater pump relay OFF
If No CAN Communication Is Available With BCM
Control part Fail-safe in operation

• Turns ON the headlamp low relay when the ignition switch is turned ON
Headlamp • Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamps
• Side marker lamps
• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
• Illuminations
• Tail lamps
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-
safe control is activated while the front wiper is set in the INT mode and the front wiper
motor is operating.
Horn Horn OFF
Ignition relay The status just before activation of fail-safe is maintained.
IGNITION RELAY MALFUNCTION DETECTION FUNCTION

• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
DTC Ignition switch Ignition relay Tail lamp relay

— ON ON —
— OFF OFF —
B2098: IGN RELAY ON OFF ON ON (10 minutes)
B2099: IGN RELAY OFF ON OFF —
NOTE:
The tail lamp turns OFF when the ignition switch is turned ON.
FRONT WIPER CONTROL

IPDM E/R detects front wiper stop position by a front wiper auto stop signal.
When a front wiper auto stop signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 second activation and 20 second stop five times.
Ignition switch Front wiper switch Auto stop signal

Front wiper stop position signal cannot be
OFF
ON input 10 seconds.
ON The signal does not change for 10 seconds.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.

< ECU DIAGNOSIS >
DTC Index INFOID:0000000005804767
CONSULT-III display Fail-safe TIMENOTE Refer to

No DTC is detected. B
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT × CRNT 1 – 39 PCS-18 C
B2098: IGN RELAY ON × CRNT 1 – 39 PCS-19
B2099: IGN RELAY OFF — CRNT 1 – 39 PCS-20
D
NOTE:
The details of TIME display are as follows.
• CRNT: The malfunctions that are detected now
• 1 - 39: The number is indicated when it is normal at present and a malfunction was detected in the past. It E
increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF → ON. It is
fixed to 39 until the self-diagnosis results are erased if it is over 39. It returns to 0 when a malfunction is
detected again in the process. F
EXL

AUTO LIGHT SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM
AUTO LIGHT SYSTEM
ABLWA0767GB

AUTO LIGHT SYSTEM
< WIRING DIAGRAM >
EXL
ABLIA2161GB

AUTO LIGHT SYSTEM
< WIRING DIAGRAM >
ABLIA2162GB

AUTO LIGHT SYSTEM
< WIRING DIAGRAM >
EXL
ABLIA2163GB

AUTO LIGHT SYSTEM
< WIRING DIAGRAM >
ABLIA2164GB

AUTO LIGHT SYSTEM
< WIRING DIAGRAM >
EXL
ABLIA2165GB

BACK-UP LAMP
< WIRING DIAGRAM >
BACK-UP LAMP
ABLWA0771GB

BACK-UP LAMP
< WIRING DIAGRAM >
EXL
ABLIA2182GB

BACK-UP LAMP
< WIRING DIAGRAM >
ABLIA2183GB

BACK-UP LAMP
< WIRING DIAGRAM >
EXL
ABLIA2184GB

BACK-UP LAMP
< WIRING DIAGRAM >
ABLIA2185GB

DAYTIME LIGHT SYSTEM
< WIRING DIAGRAM >
A
EXL
P
ABLWA0765GB

< WIRING DIAGRAM >
ABLWA0766GB

< WIRING DIAGRAM >
EXL
ABLIA2155GB

< WIRING DIAGRAM >
ABLIA2156GB

< WIRING DIAGRAM >
EXL
ABLIA2157GB

< WIRING DIAGRAM >
ABLIA2158GB

< WIRING DIAGRAM >
EXL
ABLIA2159GB

< WIRING DIAGRAM >
ABLIA2160GB

HEADLAMP
< WIRING DIAGRAM >
HEADLAMP
A
EXL
P
ABLWA0764GB

HEADLAMP
< WIRING DIAGRAM >
ABLIA2150GB

HEADLAMP
< WIRING DIAGRAM >
EXL
ABLIA2151GB

HEADLAMP
< WIRING DIAGRAM >
ABLIA2152GB

HEADLAMP
< WIRING DIAGRAM >
EXL
ABLIA2153GB

HEADLAMP
< WIRING DIAGRAM >
ABLIA2154GB

< WIRING DIAGRAM >
A
EXL
P
ABLWA0769GB

< WIRING DIAGRAM >
ABLIA2173GB

< WIRING DIAGRAM >
EXL
ABLIA2174GB

< WIRING DIAGRAM >
ABLIA2175GB

< WIRING DIAGRAM >
EXL
ABLIA2176GB

< WIRING DIAGRAM >
ABLIA2177GB

< WIRING DIAGRAM >
EXL
ABLIA2178GB

STOP LAMP
< WIRING DIAGRAM >
STOP LAMP
ABLWA0770GB

STOP LAMP
< WIRING DIAGRAM >
EXL
ABLIA2179GB

STOP LAMP
< WIRING DIAGRAM >
ABLIA2180GB

STOP LAMP
< WIRING DIAGRAM >
EXL
ABLIA2181GB

< WIRING DIAGRAM >
ABLWA0768GB

< WIRING DIAGRAM >
EXL
ABLIA2166GB

< WIRING DIAGRAM >
ABLIA2167GB

< WIRING DIAGRAM >
EXL
ABLIA2168GB

< WIRING DIAGRAM >
ABLIA2169GB

< WIRING DIAGRAM >
EXL
ABLIA2170GB

< WIRING DIAGRAM >
ABLIA2171GB

< WIRING DIAGRAM >
EXL
ABLIA2172GB

EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
Symptom Table INFOID:0000000005439304
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom Possible cause Inspection item

• Fuse
• Harness between IPDM E/R
and the front combination lamp Headlamp (HI) circuit
One side
• Front combination lamp Refer to EXL-36.
Headlamp does not (High beam relay)
switch to the high beam. • IPDM E/R
Symptom diagnosis
Both sides "BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM"
Refer to EXL-142.
• Combination meter.
High beam indicator lamp is not turned ON. • Combination meter Data monitor "HI-BEAM IND"
(Headlamp switches to the high beam.) • BCM • BCM (HEAD LAMP)
Active test "HEADLAMP"
Front combination lamp (Low
One side —
beam relay)
• Combination switch (lighting
and turn signal switch)
Combination switch (lighting and
• Harness between the combina-
turn signal switch)
Headlamp does not tion switch (lighting and turn sig-
Refer to EXL-19.
switch to the low beam. nal switch) and BCM
Both sides • BCM
High beam request signal IPDM E/R
• BCM Data monitor "HL HI REQ"
• IPDM E/R
IPDM E/R —
• Fuse
• Bulb
• Harness between IPDM E/R Headlamp (LO) circuit
One side
and the front combination lamp Refer to EXL-38.
Headlamp does not turn • Front combination lamp
ON. • IPDM E/R
Symptom diagnosis
Both sides "BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON"
Refer to EXL-143.
• BCM Combination switch (lighting and
When the ignition
• Combination switch (lighting turn signal switch)
switch is turned ON
and turn signal switch) Refer to EXL-19.
Headlamp does not turn
OFF. The ignition switch is
turned OFF (After acti-
IPDM E/R —
vating the battery sav-
er).

Symptom Possible cause Inspection item
A
Combination switch (lighting and
• Harness between the combina-
turn signal switch)
tion switch (lighting and turn sig- B
Refer to EXL-19.
Headlamp is not turned ON/OFF with the lighting nal switch) and BCM
switch AUTO. • BCM
• Optical sensor
• Harness between the optical Optical sensor
C
sensor and BCM Refer to EXL-46.
• BCM
• Either high beam bulb D
• Parking brake switch
Daytime light system does not activate. Daytime light system description. E
• BCM
Refer to EXL-9.
• IPDM E/R
• Daytime light relay
• Harness between IPDM E/R
F
and daytime light relay.
• Fuse
• Parking lamp bulb
• Harness between IPDM E/R G
Parking lamp circuit
One side and the front/rear combination
Refer to EXL-40.
lamp
Parking lamp is not turned • Front/rear combination lamp
ON. H
• IPDM E/R
Symptom diagnosis
"PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED
Both sides I
ON"
Refer to EXL-144.
Indicator lamp is nor- • Harness between BCM and
mal. each turn signal lamp J
Turn signal lamp does not Turn signal lamp circuit
(The applicable side • Turn signal lamp bulb
blink. Refer to EXL-43.
performs the high flash- • Door mirror (if equipped with
er activation). turn signals in the door mirrors)
K
One side Combination meter —
• Turn signal indicator lamp sig- • Combination meter.
Both sides nal Data monitor "TURN IND"
(Always) • Combination meter • BCM (FLASHER) EXL
Turn signal indicator lamp • BCM Active test "FLASHER"
does not blink.
Both sides
(Does blink when acti- • The combination meter power Combination meter M
vating the hazard warn- supply and the ground circuit Power supply and the ground circuit
ing lamp with the • Combination meter Refer to MWI-40.
ignition switch OFF)
N

BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
The headlamps (both sides) do not switch to high beam when the combination switch (lighting and turn signal
switch) is in the HI or PASS setting.
1.COMBINATION SWITCH (LIGHTING AND TURN SIGNAL SWITCH) INSPECTION

Check the combination switch (lighting and turn signal switch). Refer to EXL-19, "System Description".
Is the combination switch (lighting and turn signal switch) normal?
YES >> GO TO 2
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "HL HI REQ" of IPDM E/R DATA MONITOR item.
2. With operation of the combination switch (lighting and turn signal switch) lighting switch, check the moni-
tor status.
Monitor item Condition Monitor status

combination HI or PASS ON
switch (lighting
HL HI REQ and turn signal Except for HI or
switch) OFF
PASS
(2ND)
Is the monitor item status normal?
YES >> GO TO 3
NO >> Replace BCM. Refer to BCS-83, "Removal and Installation" .
3.HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to EXL-36, "Diagnosis Procedure".
Is the headlamp (HI) circuit normal?
YES >> Replace IPDM E/R. Refer to PCS-36, "Removal and Installation" .

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
A
The headlamps (both sides) do not turn ON in any combination switch (lighting and turn signal switch) setting. B
1.CHECK COMBINATION SWITCH (LIGHTING AND TURN SIGNAL SWITCH) C

D
YES >> GO TO 2
2.CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT E
1. Select "HL LO REQ" of IPDM E/R DATA MONITOR item.
2. With operation of the combination switch (lighting and turn signal switch), check the monitor status. F

combination 2ND ON G
switch (lighting
HL LO REQ
and turn signal OFF OFF
switch)
H
YES >> GO TO 3
NO >> Replace BCM. Refer to BCS-83, "Removal and Installation". I
3.HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to EXL-38, "Diagnosis Procedure".
J
Is the headlamp (LO) circuit normal?
YES >> Replace IPDM E/R. Refer to PCS-36, "Removal and Installation".
K
EXL

PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
The parking, license plate and tail lamps do not turn ON in with any combination switch (lighting and turn sig-
nal switch) setting.
1.COMBINATION SWITCH (LIGHTING AND TURN SIGNAL SWITCH) INSPECTION

YES >> GO TO 2
2.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
1. Select "TAIL & CLR REQ" of IPDM E/R DATA MONITOR item.
2. With operation of the combination switch (lighting and turn signal switch), check the monitor status.

combination 1ST ON
TAIL & CLR switch (lighting
REQ and turn signal OFF OFF
switch)
YES >> GO TO 3
NO >> Replace BCM. Refer to BCS-83, "Removal and Installation".
3.PARK LAMP CIRCUIT INSPECTION
Check the parking lamp circuit. Refer to EXL-40, "Diagnosis Procedure".
Is the tail lamp circuit normal?
YES >> Replace IPDM E/R. Refer to PCS-36, "Removal and Installation".

NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
A
AUTO LIGHT SYSTEM B

The auto light system may not turn the headlamp ON/OFF immediately after passing a dark area or a bright
area (short tunnel, sky bridge, shadowed area etc.). This is normal.
C
EXL

PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000005806164
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions For High-Voltage System INFOID:0000000005439315
Refer to HBB-114, "Precautions For High-Voltage System".

General precautions for service operations INFOID:0000000005439316
• Never work with wet hands.

• Turn the lighting switch OFF before disconnecting and connecting the connector.
• When checking the headlamp on/off operation, check it on vehicle and with the power connected to the vehi-
cle-side connector.
• Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.
• When the bulb has burned out, wrap it in a thick vinyl bag and discard. Do not break the bulb.
• Leaving the bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when replac-
ing the bulb.
• When adjusting the headlamp aiming, turn the aiming adjustment screw only in the tightening direction. (If it
is necessary to loosen the screw, first fully loosen the screw, and then turn it in the tightening direction.)
• Do not use organic solvent (paint thinner or gasoline) to clean lamps and to remove old sealant.

HEADLAMP
< ON-VEHICLE MAINTENANCE >
ON-VEHICLE MAINTENANCE A
HEADLAMP
Aiming Adjustment INFOID:0000000005806165
B
PREPARATION BEFORE ADJUSTING

NOTE: C
• For details, refer to the regulations in your area.
• Perform aiming adjustment if the vehicle front body has been repaired and/or the front combination lamp
assembly has been replaced.
D
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to specification.
• Position vehicle and screen on level surface.
E
• Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
• Ensure engine coolant and engine oil are filled to correct levels and fuel tank is full.
• Confirm spare tire, jack and tools are properly stowed.
• Wipe off dirt on the headlamp. F
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
G
EXL
ALLIA0034ZZ
Aiming Adjustment procedure

M
1. Position the screen.
NOTE:
• Stop the vehicle facing the screen.
• Place the screen on a plain road vertically. N
2. Face the screen with the vehicle. Maintain 7.62 m (25 ft) between the headlamp bulb center and the
screen.
3. Start the engine. Turn the headlamp (LO) ON. O
CAUTION:
Never cover the lens surface with tape, etc. The lens is made of resin.
NOTE: P
• Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
• For horizontal aiming, adjust headlamp until beam pattern is at horizontal center point.

HEADLAMP
< ON-VEHICLE MAINTENANCE >
AWLIA1498ZZ
A. Right B. Left C. Center of headlamp bulb-(HV point)

D. Cutoff line E. Screen F. Aim evaluation segment
G. Step H. Horizontal center line of head lamp J. 53.2 mm (2.09 in)
K. -13.3 mm (-0.52 in) L. 7.62 m (25 ft) M. 399 mm (15.71 in)
N. 133 mm (5.24 in) V. Vertical center line of headlamp
• Basic illuminating area for adjustment should be within the range shown on the aiming chart. Adjust head-
lamps accordingly.

HEADLAMP
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR A
HEADLAMP
Bulb Replacement INFOID:0000000005439319
B
HEADLAMP
CAUTION: C
Do not touch the glass of bulb directly by hand. Keep grease and other oily substances away from
bulb. Do not touch bulb by hand while it is lit or right after being turned off, burning may result.
Removal D
1. Position the fender protector aside. Refer to EXT-19, "Removal and Installation".
2. Turn the headlamp bulb sockets counterclockwise to unlock and remove them.
3. Turn the high beam lamp bulb socket counterclockwise to unlock and remove it. E
Installation
Installation is in the reverse order of removal.
CAUTION: F
After installing a headlamp bulb, be sure to install the bulb socket securely to ensure watertightness.
SIDE MARKER LAMP
G
Removal
2. Turn side marker bulb socket counterclockwise to unlock it. H
3. Pull bulb to remove it.
Installation
I
FRONT PARK/TURN SIGNAL LAMP
Removal J
2. Turn the park/turn bulb socket counterclockwise to unlock it.
K
3. Pull the bulb to remove it.
Installation
Installation is in the reverse order of removal. EXL
CAUTION:
After installing a headlamp bulb, be sure to install the bulb socket securely to ensure watertightness.
Removal and Installation INFOID:0000000005439320 M
COMBINATION LAMP
Removal N
1. Remove the front bumper fascia. Refer to EXT-13, "Removal and Installation".
2. Ensure lighting switch is OFF.
O
3. Remove the headlamp bolts (A).
4. Pull the headlamp assembly (1) toward the front of the vehicle,
detach the headlamp harness (2) from the headlamp assembly P
(1), disconnect the bulb connectors and remove.
AWLIA1777ZZ

HEADLAMP
Installation
NOTE:
Confirm headlamp aiming adjustment. Refer to EXL-147, "Aiming Adjustment".
Disassembly and Assembly INFOID:0000000005439321
Combination Lamp
AWLIA1776ZZ
1. Headlamp assembly 2. Halogen lamp bulb (high beam) 3. Halogen lamp bulb (low beam)
4. Front park/turn signal lamp bulb socket 5. Front park/turn signal lamp bulb 6. Side marker lamp bulb socket
7. Side marker lamp bulb
Disassembly
CAUTION:
• Do not touch the glass of the bulb directly by hand. Keep grease and other oily substances away
from bulb. Do not touch bulb while it is lit or right after being turned off, burning may result.
1. Turn the halogen lamp bulb (low beam) counterclockwise to unlock and remove it.
2. Turn the halogen lamp bulb (high beam) socket counterclockwise to unlock and remove it.
3. Turn the front park/turn signal lamp bulb socket counterclockwise to unlock and remove it.
4. Pull the front park/turn signal lamp bulb from its socket.
5. Turn the side marker lamp bulb socket counterclockwise to unlock and remove it.
6. Pull the side marker lamp bulb from its socket.
Assembly
Assembly is in the reverse order of disassembly.

A
Removal and Installation INFOID:0000000005439324
REMOVAL B
1. Disconnect the IPDM E/R. Refer to PCS-36, "Removal and Installation".
2. Disconnect the harness junction block to position it aside.
C
3. Remove the DTRL relay (1).
• : Front
F
ALLIA0835ZZ
INSTALLATION
Installation is in the reverse order of removal. G
EXL

STOP LAMP
STOP LAMP
HIGH-MOUNTED STOP LAMP - WITH REAR SPOILER

Removal
1. Remove the rear spoiler. Refer to EXT-26, "Removal and Installation".
2. Remove the two screws and remove the LED stop lamp from the rear spoiler.
Installation
HIGH-MOUNTED STOP LAMP - WITH PARCEL SHELF
Removal
1. Slide high-mounted stop lamp assembly rearward on parcel
shelf to give clearance to front tabs.
2. Lift front of lamp assembly up and bring forward to give clear-
ance to rear tabs.
3. Disconnect the high-mounted connector and remove.
LKIA0063E
Installation
HIGH-MOUNTED STOP LAMP - WITH REAR SPOILER

Removal
The high-mounted stop lamp uses an LED circuit board instead of a bulb. The LED circuit board is not service-
able and the high-mounted stop lamp must be replaced as an assembly.
HIGH MOUNTED STOP LAMP - WITH PARCEL SHELF
Removal
1. Remove high mounted stop lamp assembly from parcel shelf.
2. Turn bulb socket counterclockwise to unlock it.
3. Pull bulb to remove it from the socket.
Installation

LICENSE PLATE LAMP
LICENSE PLATE LAMP
A
LICENSE PLATE LAMP B

Removal
1. Position trunk lid finisher aside.
C
2. Turn license plate lamp bulb socket counterclockwise to unlock
and remove.
3. Pull license plate lamp bulb to remove from socket. D
F
WKIA3384E
Installation
Installation is in the reverse order of removal. G
H
LICENSE PLATE LAMP
Removal
1. Remove the license plate finisher. Refer to EXL-153, "Removal and Installation". I
2. Disconnect the license plate lamp connector.
3. Remove the license plate lamp screw and remove the license
plate lamp. J
EXL
PKIA0059E
M
Installation
N

REAR COMBINATION LAMP
REAR TURN SIGNAL LAMP

Removal
1. Remove the rear combination lamp. Refer to EXL-154, "Removal and Installation".
2. Turn the rear turn signal lamp bulb socket counterclockwise and remove it.
3. Remove the rear turn signal lamp bulb.
Installation
STOP/TAIL LAMP
Removal
2. Turn the stop/tail lamp bulb socket counterclockwise and remove it.
3. Remove the stop/tail lamp bulb.
Installation
BACK-UP LAMP
Removal
2. Turn the back-up lamp bulb socket counterclockwise and remove it.
3. Remove the back-up lamp bulb.
Installation
SIDE MARKER LAMP
Removal
2. Turn the side marker lamp bulb socket counterclockwise and remove it.
3. Remove the side marker lamp bulb.
Installation
COMPONENTS

H
ALLIA0039ZZ
1. Rear combination lamp assembly 2. Back-up lamp bulb 3. Stop/Tail lamp bulb
4. Rear combination lamp harness 5. Side marker lamp bulb 6. Rear turn signal lamp bulb I
REMOVAL
1. Partially remove trunk side finisher. Refer to INT-30, "Removal and Installation". J
2. Remove trunk rear finisher. Refer to INT-30, "Removal and Installation".
3. Remove the rear combination lamp nuts.
4. Pull the rear combination lamp assembly toward rear of the vehicle and remove. K
INSTALLATION
Installation is the reverse order of removal.
EXL

LIGHTING AND TURN SIGNAL SWITCH
LIGHTING AND TURN SIGNAL SWITCH
JPMIA1121ZZ
1. Combination switch 2. Combination switch connector
NOTE:
• Shown with steering wheel removed for clarity only.
• The lighting and turn signal switch are part of the combination switch assembly.
REMOVAL
1. Unlock steering wheel.
2. Disconnect battery.
CAUTION:
• Before servicing, disconnect both battery terminals and wait at least three minutes.
• Do not use air tools or electric tools for servicing.
• After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis func-
tion and delete the memory with CONSULT-III.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair mal-
functions. Refer to SRC-12, "SRS Operation Check".
3. Remove steering column covers. Refer to IP-10, "Exploded View".

4. Rotate steering wheel clockwise to access first combination switch bolt and remove the bolt.
5. Rotate steering wheel counter-clockwise to access second combination switch bolt and remove the bolt.
6. Disconnect electrical connectors and remove the combination switch.
INSTALLATION

HAZARD SWITCH
HAZARD SWITCH
A
Removal B
1. Remove the center ventilator grilles. Refer to VTL-24, "CENTER VENTILATOR GRILLES : Removal and
Installation".
2. Disconnect passenger air bag and hazard switch connectors. C
3. Remove the hazard switch screws (A) and remove the hazard
switch (1).
D
F
ALLIA0037ZZ
Installation G
EXL

SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
Headlamp INFOID:0000000005439333
Item Wattage (W)*

Low 55
High 60
*: Always check with the Parts Department for the latest parts information.
Exterior Lamp INFOID:0000000005439334
Item Wattage (W)*

Park/turn signal lamp 27/8
Side marker lamp 5
Stop/Tail lamp 27/8
Turn signal lamp 27
Rear combination lamp
Back-up lamp 13
Side marker lamp 5
License plate lamp 5
High-mounted stop lamp (parcel shelf mount) 18
High-mounted stop lamp (rear air spoiler mount) LED
*: Always check with the Parts Department for the latest parts information.

Exterior Lighting System: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Exterior Lighting System: Section

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

DIAGNOSIS AND REPAIR WORKFLOW .......... 4 DIAGNOSIS SYSTEM (BCM) ........................... 23

Revision: September 2009 EXL-1 2010 Altima HEV

Revision: September 2009 EXL-3 2010 Altima HEV

Revision: September 2009 EXL-4 2010 Altima HEV

Revision: September 2009 EXL-5 2010 Altima HEV

Revision: September 2009 EXL-6 2010 Altima HEV

Revision: September 2009 EXL-7 2010 Altima HEV

Component Description INFOID:0000000005439231

LOW BEAM OPERATION

Revision: September 2009 EXL-8 2010 Altima HEV

System Description INFOID:0000000005439233

Revision: September 2009 EXL-9 2010 Altima HEV

Component Description INFOID:0000000005439235

Revision: September 2009 EXL-10 2010 Altima HEV

Engine With engine stopped With engine running D

Revision: September 2009 EXL-11 2010 Altima HEV

System Description INFOID:0000000005439237

Revision: September 2009 EXL-12 2010 Altima HEV

Component Description INFOID:0000000005439239

Revision: September 2009 EXL-14 2010 Altima HEV

System Description INFOID:0000000005439245

Revision: September 2009 EXL-15 2010 Altima HEV

TURN SIGNAL OPERATION

Revision: September 2009 EXL-16 2010 Altima HEV

System Description INFOID:0000000005439249

Revision: September 2009 EXL-17 2010 Altima HEV

PARKING, LICENCE PLATE AND TAIL LAMPS OPERATION

Revision: September 2009 EXL-18 2010 Altima HEV

Combination switch INPUT-OUTPUT system list P

Revision: September 2009 EXL-19 2010 Altima HEV

COMBINATION SWITCH READING FUNCTION

Revision: September 2009 EXL-20 2010 Altima HEV

Revision: September 2009 EXL-21 2010 Altima HEV

Intermittent oper- INT VOLUME switch ON/OFF status

Revision: September 2009 EXL-22 2010 Altima HEV

Revision: September 2009 EXL-23 2010 Altima HEV

Work item Setting item Setting

ON1 With the exterior lamp battery saver function

Revision: September 2009 EXL-24 2010 Altima HEV

AUTO LIGHT SW1 F

Revision: September 2009 EXL-25 2010 Altima HEV

Service item Setting item Setting

Test item Operation Description

Monitor item [UNIT] Description

Revision: September 2009 EXL-26 2010 Altima HEV

BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) INFOID:0000000005804806

Work item Setting item Setting J

ON* With the exterior lamp battery saver function EXL

Revision: September 2009 EXL-27 2010 Altima HEV

Test item Operation Description

Revision: September 2009 EXL-28 2010 Altima HEV

AUTO ACTIVE TEST B

Revision: September 2009 EXL-29 2010 Altima HEV

6* Cooling fans MID for 5 seconds → HI for 5 seconds

Revision: September 2009 EXL-30 2010 Altima HEV

Symptom Inspection contents Possible cause

• Combination meter signal

Revision: September 2009 EXL-31 2010 Altima HEV

CONSULT - III Function (IPDM E/R) INFOID:0000000005804808

Diagnosis mode Description

Monitor Item MAIN SIG-