Warning Chime System: Section
Warning Chime System: Section
Warning Chime System: Section
WCS
A
B
SECTION
WARNING CHIME SYSTEM C
E
CONTENTS
PRECAUTION ............................................... 3 CONSULT Function .................................................14 F
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING: E
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, it is recommended that all maintenance
F
and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see “SRS AIR BAG”. G
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. H
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation. I
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing J
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery or batteries, and wait at least 3 minutes before performing any service.
K
Precautions for Removing Battery Terminal INFOID:0000000012926050
JSNIA3559ZZ
H
1. Parking brake switch 2. Combination meter 3. ABS actuator and electric unit (con-
trol unit)
Refer to BRC-9, "Component Parts
Location".
I
4. BCM 5. Seat belt buckle switch (driver side)
Refer to BCS-5, "BODY CONTROL
SYSTEM : Component Parts Loca- J
tion"
Unit Description
• Receives a buzzer output signal from the BCM with CAN communication line and sounds the
L
buzzer.
Combination meter • Judges whether the parking brake is released from the vehicle speed signal received from the
ABS actuator and electric unit (control unit) with CAN communication line and the parking
M
brake switch signal from the parking brake switch, and sounds the buzzer if necessary.
Based on the signals received from various units and switches, transmits the buzzer output sig-
BCM
nal to the combination meter via CAN communication.
WCS
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter via CAN communication.
(control unit)
Seat belt buckle switch (driver
side)
Transmits a seat belt buckle switch signal (driver side) to the combination meter. O
Combination switch
Transmits the combination switch signal to BCM.
(Lighting switch)
P
Front door switch (driver side) Transmits the driver side door switch signal to BCM.
Parking brake switch Transmits the parking brake switch signal to the combination meter.
The buzzer (1) for the warning chime system is integrated in the
combination meter.
JSNIA3231ZZ
F
JSNIA3116GB
G
WARNING CHIME SYSTEM : System Description INFOID:0000000012201465
COMBINATION METER
H
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer
output signal transmitted from each unit.
BCM I
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
WARNING CHIME FUNCTION LIST J
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
Function Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Illumination control When suspending communication, changes to nighttime mode.
Shift position indicator When suspending communication, not indicate.
Instantaneous fuel consumption • When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
Average fuel consumption
cate the result.
Information display Possible driving distance • When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition is
Torque distribution indicator indicated.
Low tire pressure warning The display turns OFF by suspending communication.
Buzzer The buzzer turns OFF by suspending communication.
ABS warning lamp
Malfunction indicator lamp
VDC warning lamp
The lamp turns ON by suspending communication.
EPS warning lamp
AWD warning lamp
Brake warning lamp
VDC OFF indicator lamp
High beam indicator lamp
Turn signal indicator lamp
Door warning lamp
Tail lamp indicator lamp
Warning lamp/indicator lamp Engine start operation indicator lamp
Shift P warning lamp
The lamp turns OFF by suspending communication.
Front fog lamp indicator lamp
Oil pressure warning lamp
CRUISE indicator lamp
AWD mode indicator lamp (AWD)
AWD mode indicator lamp (AWD-V)
Key warning lamp
CVT indicator lamp
Low tire pressure warning lamp After blinking for 1 minute, the lamp remains ON.
High coolant temperature indicator When reception time of an abnormal signal is more than 60
lamp seconds, the lamp turns OFF.
JSNIA2421GB
A
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled.
B
Operation conditions
Ignition switch OFF or ACC position
C
Combination switch (Lighting
1st or 2nd position
switch)
Driver side door Open [front door switch (driver side) ON]
D
WARNING CHIME CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
E
Operation conditions
Ignition switch ON
F
Combination switch (Lighting
OFF or AUTO position
switch)
Driver side door Close [front door switch (driver side) OFF]
G
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below. H
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig- K
nal) from BCM.
WCS
JSNIA2426GB
JSNIA3118GB
Operation conditions
Ignition switch ON
Driver seat belt Unfastened [seat belt buckle switch (driver side) ON]
Operation conditions
Ignition switch OFF
Seat belt (driver side) Fastened (driver side seat belt buckle switch OFF)
6 seconds after the start of warning sound
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below.
Seat belt buckle switch signal Seat belt buckle switch (driver side) Combination meter B
(driver side)
BCM
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig- C
nal) from BCM.
JSNIA3123GB J
SOUND SPECIFICATION
K
M
JSNIA3111GB
JSNIA2422GB
Operation conditions
Ignition switch ON
Parking brake During the operation (parking brake switch ON)
Vehicle speed Approximately 7 km/h (4.3 MPH) or more
Operation conditions
Ignition switch OFF
Parking brake Release condition (parking brake switch OFF)
Vehicle speed Approximately 3 km/h (1.9 MPH) or less
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
TIMING CHART
JSNIA2428GB
JSNIA3640GB
WCS
MAIN
Display item [Unit] Description
SIGNALS
Value of vehicle speed signal received from ABS actuator and electric unit (control
SPEED METER unit) via CAN communication.
X
[km/h] NOTE:
655.35 is displayed when the malfunction signal is received.
Vehicle speed signal value transmitted to other units via CAN communication.
SPEED OUTPUT
X NOTE:
[km/h]
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
• Value of the engine speed signal received from TCM via CAN communication
(CVT models).
TACHO METER • Value of the engine speed signal received from ECM via CAN communication
X
[rpm] (M/T models).
NOTE:
8191.875 is displayed when the malfunction signal is received.
FUEL METER
X Fuel level indicated on combination meter.
[L]
Value of engine coolant temperature signal is received from ECM via CAN com-
W TEMP METER munication.
X
[°C] NOTE:
215 is displayed when the malfunction signal is input.
FUEL CAP W/L Status of fuel filler cap warning display detected from fuel filler cap warning display
[On/Off] signal received from ECM via CAN communication.
ABS W/L Status of ABS warning lamp detected from ABS warning lamp signal is received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
VDC/TCS IND
is received from ABS actuator and electric unit (control unit) via CAN communica-
[On/Off]
tion.
SLIP IND Status of VDC warning lamp detected from VDC warning lamp signal received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Warning History
Revision: November 2015 WCS-16 2016 JUKE
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
• Stores histories when warning/indicator lamp is turned on.
• “Warning History” indicates the “TIME” when the warning/indicator lamp is turned on. A
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
B
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO Warning History: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• Warning History is not stored for approximately 30 seconds after the engine starts. C
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item D
WCS
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
Air conditioning system AIR CONDITONER × ×*
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
NVIS - NATS IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door open TRUNK ×
Theft warning alarm THEFT ALM × × ×
RAP RETAINED PWR ×
Signal buffer system SIGNAL BUFFER × ×
TPMS AIR PRESSURE MONITOR × × ×
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
Display item
Description
[Unit]
PUSH SW
Status of push-button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off]
VEH SPEED 1
Value of vehicle speed signal received from combination meter with CAN communication line.
[km/h]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM using the combination switch readout function.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
CDL LOCK SW
Status of door lock unlock switch judged by BCM.
[On/Off]
ACTIVE TEST
Display item
Description
[Unit]
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
KEY REMINDER WARN The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
JSNIA0623ZZ
PHYSICAL VALUES
Terminal No. A
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
B
1
— CAN-H — — — —
(L)
2 C
— CAN-L — — — —
(P)
NOTE:
The maximum voltage varies de-
pending on the specification D
(destination unit).
Ignition Speedometer operated
4 Vehicle speed signal
(Y)
Ground
(8-pulse)
Output switch [When vehicle speed is ap- E
ON prox. 40 km/h (25 MPH)]
F
JSNIA0012GB
Ignition
6 JSNIA3305ZZ
Ground Fuel level sensor signal Input switch —
(BR) AWD J
ON
JSNIA3721ZZ
L
Air bag warning lamp
Ignition 4V
7 ON
Ground Air bag signal Input switch M
(R) Air bag warning lamp
ON 0V
OFF
8*1 — — — — — —
(P) WCS
When driver seat belt is fas-
12 V
9 Seat belt buckle switch sig- Engine tened.
Ground Input O
(W) nal (driver side) idling When driver seat belt is un-
0V
fastened.
Ignition Parking brake applied. 0V
10 P
Ground Parking brake switch signal Input switch
(SB) Parking brake released. 5V
ON
JPNIA1687GB
Ignition
13
Ground Illumination control signal Output switch
(GR)
ON
• Lighting switch 1ST
• When meter illumination
is step 6
JPNIA1686GB
Ignition
19 Changes depending to am-
Ground Ambient sensor signal Input switch
(GR) bient temperature.
ON
JSNIA0014GB
Ignition
20
Ground Ambient sensor ground — switch — 0V
(R)
ON
Ignition
21
Ground Ground — switch — 0V
(B)
ON
Ignition
22
Ground Ground — switch — 0V
(B)
ON
24
Ignition C
Ground Fuel level sensor ground — switch — 0V
(L)
ON
Ignition D
25
Ground VDC ground — switch — 0V
(B)
ON
O
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
Function Specifications P
Speedometer
Reset to zero by suspending communication.
Tachometer
Illumination control When suspending communication, changes to nighttime mode.
Shift position indicator When suspending communication, not indicate.
WCS
ECU Reference
BCS-39, "Reference Value"
BCS-60, "Fail-safe"
BCM
BCS-61, "DTC Inspection Priority Chart"
BCS-62, "DTC Index"
WCS
JRNWF0721GB
JRNWF0722GB
WCS
JRNWF0723GB
JRNWF0724GB
WCS
JRNWF0725GB
JRNWF0726GB
OVERALL SEQUENCE
C
K
JSNIA4492GB
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM L
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
M
>> GO TO 2.
2.CHECK SYMPTOM WCS
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
O
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS P
1. Connect CONSULT and perform self-diagnosis. Refer to WCS-19, "BUZZER : CONSULT Function (BCM
- BUZZER)" .
2. When DTC is detected, follow the instructions below:
- Record DTC and Freeze Frame Data.
Are self-diagnosis results normal?
YES >> GO TO 4.
NO >> GO TO 5.
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 1.
1.CHECK FUSE C
Check for blown fuses.
D
Power source Fuse No.
Battery 13
Ignition switch ON or START 5 E
Ignition switch ACC or ON 19
Is the inspection result normal?
YES >> GO TO 2. F
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT G
Check voltage between combination meter harness connector and ground.
Terminals H
(+) (−) Ignition switch po- Voltage
Combination meter sition (Approx.)
Connector Terminal
I
27 Ground OFF
M34 15 ACC Battery voltage J
28 ON
Is the inspection result normal?
YES >> GO TO 3. K
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT L
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.
M
Combination meter
Continuity
Connector Terminal WCS
21
Ground
22
M34 Existed
23 O
25
Is the inspection result normal? P
YES >> INSPECTION END
NO >> Repair harness or connector.
BUZZER
Under the condition of buzzer input : On
Except above : Off
Is the inspection result normal?
YES >> Replace combination meter.
NO >> Replace BCM. Refer to BCS-94, "Removal and Installation".
Diagnosis Procedure INFOID:0000000012201484
BUCKLE SW C
When driver seat belt is fastened : Off
When driver seat belt is unfastened : On
D
>> INSPECTION END
Diagnosis Procedure INFOID:0000000012201486 E
Combination meter
Continuity
Connector Terminal Ground J
M34 9 Not existed
Is the inspection result normal?
YES >> GO TO 2. K
NO >> Repair harness or connector.
2.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) GROUND CIRCUIT L
Check harness continuity between seat belt buckle switch (driver side) harness connector and ground.
Terminals
K
Combination meter Continuity
Connector Terminal Ground
M34 10 Not existed L
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector. M
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure INFOID:0000000012201491
Light reminder warning chime does not sound even though headlamp is illuminated. B
Diagnosis Procedure INFOID:0000000012201493
Perform a unit check for the driver side door switch. Refer to DLK-78, "Component Inspection".
Is the inspection result normal? H
YES >> Replace BCM. Refer to BCS-94, "Removal and Installation".
NO >> Replace driver side door switch. Refer to DLK-169, "Removal and Installation".
I
WCS