Warning Chime System: Section

DRIVER INFORMATION & MULTIMEDIA
SECTION
WARNING CHIME SYSTEM
WCS B
E
CONTENTS
BASIC INSPECTION .................................... 3 PARKING BRAKE RELEASE WARNING CHIME F
: System Description ................................................. 9
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 PARKING BRAKE RELEASE WARNING CHIME
Work Flow ................................................................. 3 : Component Parts Location ....................................10 G
PARKING BRAKE RELEASE WARNING CHIME
FUNCTION DIAGNOSIS ............................... 5 : Component Description .........................................10
WARNING CHIME SYSTEM ............................... 5 DIAGNOSIS SYSTEM (METER) ....................... 11 H
CONSULT-III Function (METER/M&A) ....................11
WARNING CHIME SYSTEM ....................................... 5
WARNING CHIME SYSTEM : System Diagram ...... 5 DIAGNOSIS SYSTEM (BCM) ........................... 15
WARNING CHIME SYSTEM : System Description I
...... 5 COMMON ITEM .........................................................15
WARNING CHIME SYSTEM : Component Parts COMMON ITEM : CONSULT-III Function (BCM -
Location ..................................................................... 6 COMMON ITEM) .....................................................15 J
WARNING CHIME SYSTEM : Component De-
scription ..................................................................... 6 BUZZER .....................................................................16
BUZZER : CONSULT-III Function (BCM - BUZZ-
LIGHT REMINDER WARNING CHIME ....................... 6 ER) ..........................................................................16 K
LIGHT REMINDER WARNING CHIME : System
Diagram ..................................................................... 7 COMPONENT DIAGNOSIS ......................... 18
LIGHT REMINDER WARNING CHIME : System L
Description ................................................................ 7
POWER SUPPLY AND GROUND CIRCUIT .... 18
LIGHT REMINDER WARNING CHIME : Compo- COMBINATION METER ............................................18
nent Parts Location ................................................... 7 COMBINATION METER : Diagnosis Procedure ....18 M
LIGHT REMINDER WARNING CHIME : Compo-
nent Description ........................................................ 8 BCM (BODY CONTROL MODULE) ..........................18
BCM (BODY CONTROL MODULE) : Diagnosis
SEAT BELT WARNING CHIME .................................. 8 Procedure ................................................................18 WCS
SEAT BELT WARNING CHIME : System Diagram
...... 8 METER BUZZER CIRCUIT ............................... 20
SEAT BELT WARNING CHIME : System Descrip- Description ...............................................................20 O
tion ............................................................................ 8 Component Function Check ....................................20
SEAT BELT WARNING CHIME : Component Diagnosis Procedure ..............................................20
Parts Location ........................................................... 9
SEAT BELT BUCKLE SWITCH SIGNAL CIR- P
SEAT BELT WARNING CHIME : Component De-
scription ..................................................................... 9 CUIT .................................................................. 21
Description ...............................................................21
PARKING BRAKE RELEASE WARNING CHIME ...... 9 Component Function Check ..................................21
PARKING BRAKE RELEASE WARNING CHIME Diagnosis Procedure ..............................................21
: System Diagram ...................................................... 9 Component Inspection .............................................22
Revision: 2008 October WCS-1 2009 370Z

WARNING CHIME SYSTEM ............................. 23 Description .............................................................. 78
Wiring Diagram - WARNING CHIME - .................... 23 Diagnosis Procedure ............................................... 78
ECU DIAGNOSIS ........................................ 27 THE LIGHT REMINDER WARNING DOES

NOT SOUND ...................................................... 79
COMBINATION METER .................................... 27 Description .............................................................. 79
Reference Value ..................................................... 27 Diagnosis Procedure ............................................... 79
Wiring Diagram - METER - ..................................... 34
Fail-Safe ................................................................. 41 THE SEAT BELT WARNING CONTINUES
DTC Index .............................................................. 42 SOUNDING, OR DOES NOT SOUND ............... 80
Description .............................................................. 80
BCM (BODY CONTROL MODULE) .................. 43 Diagnosis Procedure ............................................... 80
Reference Value ..................................................... 43
Wiring Diagram - BCM - ......................................... 66 PRECAUTION ............................................ 81
Fail-safe .................................................................. 71
DTC Inspection Priority Chart .............................. 74 PRECAUTIONS ................................................. 81
DTC Index .............................................................. 75 Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SYMPTOM DIAGNOSIS ............................. 78 SIONER" ................................................................. 81
Precaution for Battery Service ................................ 81
THE PARKING BRAKE RELEASE WARNING
CONTINUES SOUNDING, OR DOES NOT
SOUND .............................................................. 78

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000004536916
B
OVERALL SEQUENCE
C
JSNIA0733GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS
Connect CONSULT-III and perform self-diagnosis. Refer to WCS-11, "CONSULT-III Function (METER/M&A)".

< BASIC INSPECTION >
Are self-diagnosis results normal?
YES >> GO TO 4.
NO >> GO TO 5.
4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 1.

< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS A
B
WARNING CHIME SYSTEM : System Diagram INFOID:0000000004536917
JPNIA1435GB
H
WARNING CHIME SYSTEM : System Description INFOID:0000000004536918
COMBINATION METER I
• The buzzer (1) for the warning chime system is integrated in the
combination meter.
• The combination meter sounds the alarm buzzer installed in the J
combination meter when receiving the buzzer output signal trans-
mitted from each unit.
• Judges whether the parking brake is released from the vehicle
speed signal received from the ABS actuator and electric unit (con- K
trol unit) with CAN communication line and the parking brake
switch signal from the parking brake switch, and sounds the buzzer
if necessary. L
JPNIA1368ZZ
BCM
M
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
BCM Warning Function List WCS
Warning functions Signal name

• Ignition switch signal O
Light reminder warning chime • Combination switch input signal
• Driver side door switch signal
• Ignition switch signal
Seat belt warning chime P
• Seat belt buckle switch signal (driver side)

WARNING CHIME SYSTEM : Component Parts Location INFOID:0000000004536919
JPNIA1419ZZ
ABS actuator and electric unit (con-

BCM
trol unit)
1. Parking brake switch 2. Refer to BCS-84, "Removal and In- 3.
Refer to BRC-11, "Component Parts
stallation".
Location".
4. Combination meter 5. Seat belt buckle switch (driver side)
WARNING CHIME SYSTEM : Component Description INFOID:0000000004536920
Unit Description
• Receives a buzzer output signal from the BCM with CAN communication line and sounds the
buzzer.
• Judges whether the parking brake is released from the vehicle speed signal received from the
Combination meter ABS actuator and electric unit (control unit) with CAN communication line and the parking
brake switch signal from the parking brake switch, and sounds the buzzer if necessary.
• Receives the seat belt buckle switch signal (driver side) from the seat belt buckle switch (driver
side) and transmits it to BCM with CAN communication line.
Transmits signals provided by various units to the combination meter with CAN communication
BCM
line.
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter with CAN communication line.
(control unit)
Seat belt buckle switch (driver
Transmits a seat belt buckle switch signal (driver side) to the combination meter.
side)
Combination switch
Transmits the combination switch INPUT signal to BCM.
(Lighting switch)
Driver side door switch Transmits the driver side door switch signal to BCM.
Parking brake switch Refer to MWI-52, "Description".
LIGHT REMINDER WARNING CHIME

LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000004536921
JPNIA1436GB
D
LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000004536922
E
DESCRIPTION
With ignition switch in the OFF or ACC position, when the driver door is open and the lighting switch is the 1st
or 2nd position, the light warning chime will sound.
• BCM detects ignition switch in the OFF or ACC position, driver side door switch ON, and lighting switch in F
1st or 2nd position. Then the BCM transmits the buzzer output signal (light reminder warning chime) to com-
bination meter with CAN communication line.
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer. G
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
• Ignition switch is in the OFF or ACC H
• Lighting switch is in the 1st or 2nd position
• Driver side door switch is ON
WARNING CANCEL CONDITIONS I
Warning is canceled if any of the following conditions is fulfilled.
• Lighting switch OFF
• Ignition switch ON J
• Driver side door switch is OFF
LIGHT REMINDER WARNING CHIME : Component Parts Location INFOID:0000000004536923
WCS
JPNIA1419ZZ P

BCM
trol unit)
stallation".
Location".

LIGHT REMINDER WARNING CHIME : Component Description INFOID:0000000004536924
Unit Description
Combination meter Receives a buzzer output signal from the BCM and sounds the buzzer.
Judges the light warning conditions from the signals provided by various switches and transmits a
BCM
buzzer output signal to the combination meter via CAN communication line if necessary.
Combination switch
Transmits the combination switch input signal to BCM.
(Lighting switch)
Driver side door switch Transmits the driver side door switch signal to BCM.
SEAT BELT WARNING CHIME

SEAT BELT WARNING CHIME : System Diagram INFOID:0000000004536925
JPNIA0750GB
SEAT BELT WARNING CHIME : System Description INFOID:0000000004536926
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi-
mately 6 seconds.
• The combination meter receives the seat belt buckle switch signal (driver side) from seat belt buckle switch
(driver side) and transmits it to the BCM via CAN communication.
• The BCM receives seat belt buckle switch signal from combination meter via CAN communication.
• The BCM detects seat belt reminder warning based on the received signal and transmits the buzzer output
signal to combination meter via CAN communication.
• The combination meter receives the buzzer output signal from BCM via CAN communication and sounds the
warning buzzer.
If all of the following conditions are fulfilled, the warning buzzer will sound.
• Ignition switch ON
• Seat belt buckle switch (driver side) is ON (driver seat belt not fastened)
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled.
• Ignition switch OFF
• Seat belt buckle switch (driver side) is OFF (driver seat belt fastened)

SEAT BELT WARNING CHIME : Component Parts Location INFOID:0000000004536927
JPNIA1419ZZ F

BCM
trol unit)
1. Parking brake switch 2. Refer to BCS-84, "Removal and In- 3. G
stallation".
Location".
H
SEAT BELT WARNING CHIME : Component Description INFOID:0000000004536928
I
Unit Description
• Receives the seat belt buckle switch signal (driver side) from the seat belt buckle switch (driver
Combination meter side) and transmits it to BCM via CAN communication line.
• Receives a buzzer output signal from the BCM and sounds the buzzer. J
Judges the seat belt warning condition according to the seat belt buckle switch signal (driver side)
BCM received from the combination meter via CAN communication and transmits a buzzer output signal
to the combination meter via CAN communication line if necessary. K
Seat belt buckle switch
Transmits the seat belt buckle switch signal (driver side) to the combination meter.
(driver side)
L
PARKING BRAKE RELEASE WARNING CHIME
PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000004536929
WCS
JPNIA0751GB
P
PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000004536930
DESCRIPTION
Parking brake release warning chime judges the remaining parking brake according to the vehicle speed sig-
nal received from the ABS actuator and electric unit (control unit) via CAN communication and the parking
brake switch signal from parking brake switch to sound the warning buzzer.

If all of the following conditions are fulfilled.
• Vehicle speed is 7 km/h (4.3 MPH) or more
• Parking brake switch ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled.
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
PARKING BRAKE RELEASE WARNING CHIME : Component Parts Location
INFOID:0000000004536931
JPNIA1419ZZ

BCM
trol unit)
stallation".
Location".
PARKING BRAKE RELEASE WARNING CHIME : Component Description INFOID:0000000004536932
Unit Description
Judges the remaining parking brake according to the vehicle speed signal received from the ABS
Combination meter actuator and electric unit (control unit) via CAN communication and the parking brake switch signal
from parking brake switch and sounds the warning buzzer.
ABS actuator and electric unit
Transmits the vehicle speed signal to the combination meter via CAN communication.
(control unit)
Parking brake switch Transmits the parking brake switch signal to the combination meter.

DIAGNOSIS SYSTEM (METER)
A
CONSULT-III Function (METER/M&A) INFOID:0000000004685222
CONSULT-III APPLICATION ITEMS B

CONSULT-III can perform the following diagnosis modes via CAN communication and the combination meter.
System Diagnosis mode Description C

Self Diagnostic Result The combination meter checks the conditions and displays memorized errors.
METER/M&A Data Monitor Displays the combination meter input/output data in real time.
Special function Lighting history of the warning lamp and indicator lamp can be checked. D
SELF DIAG RESULT

Refer to WCS-42, "DTC Index". E
DATA MONITOR
Display Item List
F
X: Applicable
MAIN
Display item [Unit] Description
SIGNALS
G
Value of vehicle speed signal received from ABS actuator and electric unit (control
SPEED METER unit) via CAN communication.
X
[km/h] NOTE:
655.35 is displayed when the malfunction signal is received. H
Vehicle speed signal value transmitted to other units via CAN communication.
SPEED OUTPUT
X NOTE:
[km/h]
655.35 is displayed when the malfunction signal is received. I
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
TACHO METER
Value of the engine speed signal received from ECM via CAN communication. J
X NOTE:
[rpm]
8191.875 is displayed when the malfunction signal is received.
FUEL METER K
X Fuel level indicated on combination meter.
[L]
Value of engine coolant temperature signal is received from ECM via CAN com-
W TEMP METER munication.
X L
[°C] NOTE:
215 is displayed when the malfunction signal is input.
ABS W/L Status of ABS warning lamp detected from ABS warning lamp signal is received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication. M
Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
VDC/TCS IND
is received from ABS actuator and electric unit (control unit) via CAN communica-
[On/Off]
tion. WCS
SLIP IND Status of SLIP indicator lamp detected from slip indicator lamp signal received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Status of brake warning lamp detected from brake warning lamp signal is received O
from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
NOTE:
[On/Off]
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON. P
DOOR W/L Status of door warning detected from door switch signal received from BCM via
[On/Off] CAN communication.
HI-BEAM IND Status of high beam indicator lamp detected from high beam request signal is re-
[On/Off] ceived from BCM via CAN communication.
TURN IND Status of turn indicator lamp detected from turn indicator signal is received from
[On/Off] BCM via CAN communication.

MAIN
SIGNALS
RR FOG IND Status of rear fog lamp indicator lamp detected from rear fog lamp status signal is
[On/Off] received from BCM via CAN communication.
LIGHT IND Status of light indicator lamp detected from position light request signal is received
[On/Off] from BCM via CAN communication.
OIL W/L Status of oil pressure warning lamp detected from oil pressure switch signal is re-
MIL Status of malfunction indicator lamp detected from malfunctioning indicator lamp
[On/Off] signal is received from ECM via CAN communication.
CRUISE IND Status of CRUISE indicator lamp detected from CRUISE indicator lamp signal is
[On/Off] received from ECM via CAN communication.
ATC/T-AMT W/L A/T CHECK indicator lamp status judged by the transmission check warning lamp
[On/Off] signal received from TCM via CAN communication.
FUEL W/L
Low-fuel warning lamp status detected by the identified fuel level.
[On/Off]
WASHER W/L Status of washer warning lamp judged from washer level switch input to combina-
[On/Off] tion meter.
AIR PRES W/L Status of low tire pressure warning lamp detected from tire pressure signal is re-
KEY G/Y W/L Status of key warning lamp (yellow) detected from key warning signal is received
[On/Off] from BCM via CAN communication.
MT SYNC REV IND Status of S-MODE indicator judged from S-MODE indicator signal received from
[On/Off] ECM with CAN communication line.
LCD
[C&P N, C&P I, B&P N, B&P I, ID NG, Displays status of Intelligent Key system warning detected from meter display sig-
ROTAT, SFT P, INSRT, BATT, NO nal is received from BCM via CAN communication.
KY, OUTKY, LK WN]
• Status of shift position indicator detected from shift position signal and manual
SHIFT IND mode indicator signal is received from TCM via CAN communication. (A/T mod-
[P, R, N, D, L, M1, M2, M3, M4, M5, els)
M6, M7] • Status of shift position indicator detected from shift position signal is received
from ECM via CAN communication. (with SynchroRev Match mode models)
AT S MODE SW
This item is displayed, but cannot be monitored.
[Off]
M RANGE SW
Status of manual mode switch.
[On/Off]
NM RANGE SW
Status of not manual mode switch.
[On/Off]
AT SFT UP SW
Status of position select switch (up).
[On/Off]
AT SFT DWN SW
Status of position select switch (down).
[On/Off]
ST SFT UP SW
Status of paddle shifter up switch.
[On/Off]
ST SFT DWN SW
Status of paddle shifter down switch.
[On/Off]
PKB SW
Status of parking brake switch.
[On/Off]
BUCKLE SW
Status of seat belt buckle switch (driver side).
[On/Off]
BRAKE OIL SW
Status of brake fluid level switch.
[On/Off]
A/C AMP CONN
Status of A/C auto amp. connection recognition signal.
[On/Off]

MAIN
SIGNALS A
ENTER SW
[On/Off] Status of (ENTER) switch.
SELECT SW B
[On/Off] Status of (SELECT) switch.
MT SYNC REV SW
Status of S-MODE switch.
[On/Off] C
DISTANCE
Value of possible driving distance calculated by combination meter.
[km]
Ambient air temperature value converted from ambient sensor signal received D
from ambient sensor.
OUTSIDE TEMP NOTE:
[°C or °F] This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient E
sensor input value.)
FUEL LOW SIG Status of fuel level low warning signal to output to AV control unit via CAN com-
[On/Off] munication. F
CRANKING SIG Cranking status judged by the engine status signal received from ECM via CAN
[On/Off] communication.
ST CNT SIG Starter relay status judged by the starter relay status signal received from BCM via G
[On/Off] CAN communication.
Buzzer status (in the combination meter) is detected from the buzzer output signal
BUZZER
X received from each unit via CAN communication and the warning output condition H
[On/Off]
of the combination meter.
NOTE:
Some items are not available according to vehicle specification. I
SPECIAL FUNCTION
Special menu J
Display item Description

W/L ON HISTORY Lighting history of warning lamp and indicator lamp can be checked. K
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on. L
• The “TIME” above is :
- 0 : The condition that the warning/indicator lamp has been turned on 1 or more times after starting the
engine and waiting for 30 seconds. M
- 1 - 39 : The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY : Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts. WCS
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item O

ABS W/L Lighting history of ABS warning lamp. P
VDC/TCS IND Lighting history of VDC OFF indicator lamp.
SLIP IND Lighting history of SLIP indicator lamp.
BRAKE W/L Lighting history of brake warning lamp.
DOOR W/L Lighting history of door warning.
TRUNK/GLAS-H This item is displayed, but cannot be monitored.

OIL W/L Lighting history of oil pressure warning lamp.
C-ENG W/L Lighting history of malfunction indicator lamp.
C-ENG2 W/L This item is displayed, but cannot be monitored.
CRUISE IND Lighting history of CRUISE indicator lamp.
SET IND This item is displayed, but cannot be monitored.
CRUISE W/L This item is displayed, but cannot be monitored.
BA W/L This item is displayed, but cannot be monitored.
O/D OFF IND This item is displayed, but cannot be monitored.
ATC/T-AMT W/L Lighting history of A/T CHECK ingicator lamp.
ATF TEMP W/L This item is displayed, but cannot be monitored.
CVT IND This item is displayed, but cannot be monitored.
SPORT IND This item is displayed, but cannot be monitored.
4WD W/L This item is displayed, but cannot be monitored.
FUEL W/L Lighting history of low fuel level warning.
WASHER W/L Lighting history of low washer fluid warning
AIR PRES W/L Lighting history of low tire pressure warning lamp.
KEY G/Y W/L Lighting history of key warning lamp (yellow).
KEY R W/L Lighting history of key warning lamp (red).
KEY KNOB W/L This item is displayed, but cannot be monitored.
SYS FAIL W/L This item is displayed, but cannot be monitored.
SFT POSI W/L This item is displayed, but cannot be monitored.
HV BAT W/L This item is displayed, but cannot be monitored.
HEV BRAKE W/L This item is displayed, but cannot be monitored.
SFT OPER W/L This item is displayed, but cannot be monitored.
CHAGE W/L Lighting history of charge warning lamp.
OIL LEV LOW This item is displayed, but cannot be monitored.
DPF W/L This item is displayed, but cannot be monitored.

DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000004685223
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
CAN Diag Support Monitor
tion manual.
E
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed. F
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × × K
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
L
— AIR CONDITONER*
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
M
Combination switch COMB SW ×
Body control system BCM ×
IVIS - NATS IMMU × × WCS
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk lid open TRUNK × ×
O
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER × × P
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
*: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.

CONSULT screen item Indication/Unit Description

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
ACC>OFF While turning power supply position from “ACC” to “OFF”
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
Power position status of
OFF>ACC While turning power supply position from “OFF” to “ACC”
Vehicle Condition the moment a particular
ON>CRANK DTC is detected While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
Power supply position is “LOCK” (Ignition switch OFF with steer-
LOCK
ing is locked.)
Power supply position is “OFF” (Ignition switch OFF with steering
OFF
is unlocked.)
ACC Power supply position is “ACC” (Ignition switch ACC)
Power supply position is “IGN” (Ignition switch ON with engine
ON
stopped)
Power supply position is “RUN” (Ignition switch ON with engine
ENGINE RUN
running)
CRANKING Power supply position is “CRANKING” (At engine cranking)
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000004536939
CONSULT-III APPLICATION ITEMS
Test item Diagnosis mode Description

Data Monitor Displays BCM input data in real time.
BUZZER
Active Test Operation of electrical loads can be checked by sending driving signal to them.
DATA MONITOR

Display item A
Description
[Unit]
PUSH SW
Status of push-button ignition switch judged by BCM.
[On/Off]
B
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off]
VEH SPEED 1 Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN C
[km/h] communication line.
KEY SW-SLOT
Status of key slot judged by BCM.
[On/Off]
D
TAIL LAMP SW
Status of each switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM. E
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
F
ACTIVE TEST
Display item G
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off). H
ID REGIST WARNING The ID regist warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
I
RUN FLAT/T WARN BUZZER The run-flat tire warning chime operation can be checked by operating the relevant function (On/Off).
KEY REMINDER WARN The key reminder warning chime operation can be checked by operating the relevant function (On/Off).
J
WCS

POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
COMBINATION METER
COMBINATION METER : Diagnosis Procedure INFOID:0000000004685220
1.CHECK FUSE
Check for blown fuses.
Power source Fuse No.

Battery 11
Ignition switch ON or START 4
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector terminals and ground.
Terminals
(+) (−) Ignition switch po- Voltage
Combination meter sition (Approx.)
Connector Terminal
Ground
1 OFF
M53 Battery voltage
2 ON
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector terminals and ground.
Combination meter
Continuity
Connector Terminal
Ground
17
M53 Existed
23
NO >> Repair harness or connector.
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000004685209
1.CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Signal name Fuse and fusible link No. A

K
Battery power supply
10
B
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown. C
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF. D
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.
E
Terminals
(+) (−) Voltage
BCM (Approx.) F
Connector Terminal
Ground
M118 1 G
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3. H
3.CHECK GROUND CIRCUIT I
Check continuity between BCM harness connector and ground.
BCM J
Continuity
Connector Terminal Ground
M119 13 Existed
K
Does continuity exist?
L
WCS

METER BUZZER CIRCUIT
METER BUZZER CIRCUIT
Description INFOID:0000000004536942
• The buzzer for warning chime system is installed in the combination meter.
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000004536943
1.CHECK OPERATION OF METER BUZZER

1. Select “BUZZER” of “BCM” on CONSULT-III.
2. Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?
NO >> GO TO 2.
2.CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.
BUZZER
Under the condition of buzzer input : On
Except above : Off
YES >> Replace combination meter.
NO >> Replace BCM. Refer to BCS-84, "Removal and Installation".
Diagnosis Procedure INFOID:0000000004536944
1.CHECK POWER SUPPLY OF COMBINATION METER

Check power supply of combination meter. Refer to WCS-18, "COMBINATION METER : Diagnosis Proce-
dure".
NO >> Repair power supply circuit of combination meter. Refer to WCS-18, "COMBINATION METER :
Diagnosis Procedure".

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
A
Transmits a seat belt buckle switch signal (driver side) to the combination meter. B
Component Function Check INFOID:0000000004536946
1.CHECK COMBINATION METER INPUT SIGNAL C

Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.
BUCKLE SW D
When seat belt is fastened : Off
When seat belt is unfastened : On
E
>> INSPECTION END

Diagnosis Procedure INFOID:0000000004536947 F

1. Turn ignition switch ON. G
2. Check voltage between combination meter harness connector terminal and ground.
Terminals H
(+) (-) Voltage
Condition
Combination meter (Approx.)
I
Connector Terminal
Ground
When seat belt is fastened 12 V
M54 35
When seat belt is unfastened 0V J
YES >> Replace combination meter
NO >> GO TO 2. K
2.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT

1. Turn ignition switch OFF. L
2. Disconnect combination meter connector and seat belt buckle switch (driver side) connector.
3. Check continuity between combination meter harness connector terminal and seat belt buckle switch
(driver side) harness connector terminal.
M
Terminals
Combination meter Seat belt buckle switch (driver side) Continuity WCS
Connector Terminal Connector Terminal
M54 35 B13 1 Exist
O
4. Check harness continuity between combination meter harness connector terminal and ground.
Terminals
P
Combination meter Continuity
M54 35 Not existed
YES >> GO TO 3.

3.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) GROUND CIRCUIT
Check harness continuity between seat belt buckle switch (driver side) harness connector terminal and
ground.
Terminals
Seat belt buckle switch (driver side) Continuity
B13 2 Exist
Component Inspection INFOID:0000000004536948
1.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)

1. Turn ignition switch OFF.
2. Disconnect the seat belt buckle switch (driver side) connector.
3. Check continuity between terminals.
Terminals
Seat belt buckle switch Condition Continuity
(driver side)
When seat belt is fastened Not existed
1 2
When seat belt is unfastened Exist
NO >> Replace seat belt buckle (driver side). Refer to SB-8, "SEAT BELT BUCKLE : Removal and Instal-
lation".

A
Wiring Diagram - WARNING CHIME - INFOID:0000000004536949
WCS
P
JCNWA1872GB

JCNWA1873GB

WCS
JCNWA1874GB

JCNWA1875GB

COMBINATION METER
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
COMBINATION METER
Reference Value INFOID:0000000004685215
B
VALUES ON THE DIAGNOSIS TOOL

C
Monitor Item Condition Value/Status
Equivalent to speedometer reading
SPEED METER Ignition switch NOTE:
While driving D
[km/h] ON 655.35 is displayed when the malfunc-
tion signal is received
Equivalent to speedometer reading
SPEED OUTPUT Ignition switch NOTE: E
While driving
[km/h] ON 655.35 is displayed when the malfunc-
tion signal is received
ODO OUTPUT Ignition switch Equivalent to odometer reading in F
—
[km/h or mph] ON combination meter
Equivalent to tachometer reading
TACHO METER Ignition switch NOTE:
While driving G
[rpm] ON 8191.875 is displayed when the mal-
function signal is received
FUEL METER Ignition switch
— Values according to fuel level H
[L] ON
Values according to engine coolant
temperature
W TEMP METER Ignition switch
[°C] ON
— NOTE: I
215 is displayed when the malfunction
signal is input
Ignition switch ABS warning lamp ON On J

ABS W/L
ON ABS warning lamp OFF Off
Ignition switch VDC OFF indicator lamp ON On

VDC/TCS IND
ON VDC OFF indicator lamp OFF Off K
Ignition switch SLIP Indicator lamp ON On

SLIP IND
ON SLIP indicator lamp OFF Off
L
Ignition switch Brake warning lamp ON On
BRAKE W/L
ON Brake warning lamp OFF Off
Ignition switch Door warning lamp ON On M

DOOR W/L
ON Door warning lamp OFF Off
Ignition switch High-beam indicator lamp ON On

HI-BEAM IND WCS
ON High-beam indicator lamp OFF Off
Ignition switch Turn signal indicator lamp ON On

TURN IND
ON Turn signal indicator lamp OFF Off O
Ignition switch Rear fog lamp indicator lamp ON On
RR FOG IND
ON Rear fog lamp indicator lamp Off
P
Ignition switch Tail lamp indicator lamp ON On
LIGHT IND
ON Tail lamp indicator lamp OFF Off
Ignition switch Oil pressure warning lamp ON On

OIL W/L
ON Oil pressure warning lamp OFF Off
Ignition switch Malfunction indicator lamp ON On

MIL
ON Malfunction indicator lamp OFF Off

COMBINATION METER
< ECU DIAGNOSIS >
Ignition switch Cruise indicator lamp ON On

CRUISE IND
ON Cruise indicator lamp OFF Off
Ignition switch A/T CHECK indicator lamp ON On

ATC/T-AMT W/L
ON A/T CHECK indicator lamp OFF Off
Ignition switch Low-fuel warning displayed On

FUEL W/L
ON Low-fuel warning not displayed Off
Ignition switch Washer warning displayed On

WASHER W/L
ON Washer warning not displayed Off
Ignition switch Low tire pressure lamp ON On

AIR PRES W/L
ON Low tire pressure lamp OFF Off
Ignition switch KEY warning lamp (yellow) ON On

KEY G/Y W/L
ON KEY warning lamp (yellow) OFF Off
Ignition switch S-MODE indicator ON On

MT SYNC REV IND
ON S-MODE indicator OFF Off
Engine start information display (A/T mod-
B&P I
Ignition switch els)
ON Engine start information display (M/T mod-
C&P I
els)
Engine start information display (A/T mod-
B&P N
Ignition switch els)
LOCK or ACC Engine start information display (M/T mod-
C&P N
els)
Ignition switch
Key ID warning display ID NG
LOCK
Ignition switch
Steering lock information display ROTAT
LOCK
LCD
Ignition switch
P position warning display SFT P
LOCK
Ignition switch
Intelligent Key insert information display INSRT
LOCK
Ignition switch
Intelligent Key low battery warning display BATT
LOCK
Ignition switch
Take away warning display NO KY
ON
Ignition switch
Key warning display OUTKY
LOCK
Ignition switch
ACC warning display LK WN
ON

COMBINATION METER
< ECU DIAGNOSIS >
A
Shift position indicator P display P
Shift position indicator R display R
Shift position indicator N display N B
Shift position indicator D display D
Shift position indicator L display L
Shift position indicator M1 display M1 C
Ignition switch
SHIFT IND
ON Shift position indicator M2 display M2
Shift position indicator M3 display M3
D
Shift position indicator M6 display M6 E
NOTE:
Ignition switch F
AT S MODE SW This item is displayed, but cannot be moni- Off
ON
tored.
Ignition switch Selector lever manual mode position On

M RANGE SW G
ON Other than the above Off
Ignition switch Selector lever manual mode position Off

NM RANGE SW
ON Other than the above On H
Ignition switch Selector lever + position On
AT SFT UP SW
Selector lever − position On I
Ignition switch
AT SFT DWN SW
Ignition switch Paddle shifter switch up operation On

ST SFT UP SW J
ON Other than above Off
Ignition switch Paddle shifter switch down operation On

ST SFT DWN SW
ON Other than above Off K
Ignition switch Parking brake switch ON On
PKB SW
ON Parking brake switch OFF Off
L
Ignition switch Seat belt not fastened On
BUCKLE SW
ON Seat belt fastened Off
Ignition switch Brake fluid level switch ON On M

BRAKE OIL SW
ON Brake fluid level switch OFF Off
Other than the following On
Ignition switch WCS
A/C AMP CONN Receives A/C auto amp. connection recog-
ON Off
nition signal
Ignition switch When is pressed On

ENTER SW O
ON
Other than the above Off
Ignition switch When is pressed On

SELECT SW P
Ignition switch S-MODE switch ON On

MT SYNC REV SW
ON S-MODE switch OFF Off
DISTANCE Ignition switch Possible driving distance calculated by
—
[km] ON combination meter

COMBINATION METER
< ECU DIAGNOSIS >
Equivalent to ambient temperature
OUTSIDE TEMP Ignition switch NOTE:
—
[°C or °F] ON This may not match the indicated value
on the information display.
Ignition switch Low fuel warning displayed On

FUEL LOW SIG
ON Low fuel warning not displayed Off
Ignition switch ON On
CRANKING SIG
At engine cranking Off
Ignition switch ON On
ST CNT SIG
At engine cranking Off
Ignition switch Buzzer ON On

BUZZER
ON Buzzer OFF Off
NOTE:
Some items are not available according to vehicle specification.
TERMINAL LAYOUT
JPNIA1458ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(V)
OFF
Ignition
2
Ground Ignition signal Input switch — Battery voltage
(O)
ON
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition Speedometer operated
3 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(L) (2-pulse)
ON prox. 40 km/h (25 MPH)]
JSNIA0015GB

COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE: B
The maximum voltage varies de-
pending on the specification
(destination unit).
C
Ignition Speedometer operated
4 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(Y) (8-pulse)
ON prox. 40 km/h (25 MPH)]
D
JSNIA0012GB
E
• Lighting switch 1ST F

• When meter illumination
is maximum
G
JPNIA1363GB
Ignition
5
Ground Illumination control signal Output switch H
(B)
ON
• Lighting switch 1ST
• When meter illumination
is step 12
I
JPNIA1362GB
• Lighting switch 1ST J

• When meter illumination 10 V
is minimum
Communication signal Ignition

9
Ground (METER⇒TRIPLE Output switch — L
(BR)
METER) ON
JPNIA1425GB
M
Communication signal Ignition WCS

10
Ground (TRIPLE Input switch —
(L)
METER⇒METER) ON
O
JPNIA1426GB
Ignition S-MODE switch operation 12 V

12
Ground S-MODE switch signal Input switch P
(G) Other than the above 0V
ON
Ignition
15
Ground ACC power supply Input switch — Battery voltage
(L)
ACC

COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Air bag warning lamp
Ignition 4V
16 ON
Ground Air bag signal Input switch
(R) Air bag warning lamp
ON 0V
OFF
Ignition
17
Ground Ground — switch — 0V
(B)
ON
Ignition
18 Changes depending to am-
Ground Ambient sensor signal Input switch
(V) bient temperature.
ON
JSNIA0014GB
Ignition
19 A/C auto amp. connection
Ground Input switch — 5V
(G) recognition signal
ON
Ignition
20
Ground Ambient sensor ground Input switch — 0V
(GR)
ON
21
— CAN-H — — — —
(L)
22
— CAN-L — — — —
(P)
Ignition
23
Ground Ground — switch — 0V
(B)
ON
Ignition
24 Fuel level sensor signal
Ground — switch — 0V
(Y) ground
ON
Ignition Charge warning lamp ON 2V
25
Ground Alternator signal Input switch
(W) Charge warning lamp OFF 12 V
ON
26 Engine Parking brake ON 0V

Ground Parking brake switch signal Input
(O) idling Parking brake OFF 12 V
Ignition Brake fluid level is normal 12 V

27 Brake fluid level switch sig-
Ground Input switch Brake fluid level is less than
(LG) nal 0V
ON LOW level
Ignition Security warning lamp ON 0V
28
Ground Security signal Input switch
(Y) Security warning lamp OFF 12 V
ON
Ignition Washer level switch ON 0V
29
Ground Washer level switch signal Input switch
(GR) Washer level switch OFF 5V
ON
Ignition Paddle shifter down opera-

32 0V
Ground Paddle shifter down signal Input switch tion
(G)
ON Other than the above 5V
Ignition Paddle shifter up operation 0V
33
Ground Paddle shifter up signal Input switch
(O) Other than the above 5V
ON

COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
Condition
Input/ (Approx.)
+ – Signal name
Output
B
Ignition
34 C
Ground Fuel level sensor signal Input switch —
(BR)
ON
JPNIA0740ZZ D
When driver seat belt is fas-
Ignition 12 V
35 Seat belt buckle switch sig- tened.
Ground Input switch E
(L) nal (driver side) When driver seat belt is un-
ON 0V
fastened.
• When getting in the pas-
senger seat. F
12 V
• When passenger seat
Ignition belt is fastened.
36 Passenger seat belt warn-
Ground Input switch
(P) ing signal • When getting in the pas-
ON G
senger seat.
0V
• When passenger seat
belt is unfastened.
H
Ignition Manual mode 12 V
37
Ground Not manual mode signal Input switch
(G) Other than the above 0V
ON
Ignition Selector lever down opera- I

38 Manual mode shift down 0V
Ground Input switch tion
(V) signal
ON Other then the above 12 V
Ignition Selector lever up operation 0V J
39 Manual mode shift up sig-
Ground Input switch
(L) nal Other then the above 12 V
ON
Ignition Manual mode 0V K
40
Ground Manual mode signal Input switch
(W) Other than the above 12 V
ON
WCS

COMBINATION METER
< ECU DIAGNOSIS >
Wiring Diagram - METER - INFOID:0000000004685216
JCNWA1864GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWA1865GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWA1866GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWA1867GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWA1868GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWA1869GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWA1870GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWA1871GB
P
Fail-Safe INFOID:0000000004685217
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

COMBINATION METER
< ECU DIAGNOSIS >
Function Specifications
Speedometer
Tachometer Reset to zero by suspending communication.
Water temperature gauge
When suspending communication, changes to nighttime
Illumination control
mode.
Door open warning
The display turns OFF by suspending communication.
Parking brake release warning
Instantaneous fuel warning • When reception time of an abnormal signal is 2 seconds or
Information display less, the last received datum is used for calculation to indi-
Average fuel consumption
cate the result.
Average vehicle speed • When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition
Travel distance is indicated.
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp
VDC OFF indicator lamp
The lamp turns ON by suspending communication.
SLIP indicator lamp
Brake warning lamp
Low tire pressure warning lamp The lamp turns ON after flashing for 1 minute.
High beam indicator lamp
Warning lamp/indicator
Turn signal indicator lamp
lamp
Light indicator lamp
Rear fog lamp indicator lamp
The lamp turns OFF by suspending communication.
Oil pressure warning lamp
Malfunction indicator lamp
CRUISE indicator lamp
Key warning lamp
DTC Index INFOID:0000000004685218
Display contents of CONSULT-III Diagnostic item is detected when ... Refer to

MWI-37,
CAN COMM CIRCUIT When combination meter is not transmitting or receiving CAN communication signal
"Diagnosis
[U1000] for 2 seconds or more.
Procedure"
MWI-38,
CONTROL UNIT (CAN) When detecting error during the initial diagnosis of the CAN controller of combina-
"Diagnosis
[U1010] tion meter.
Procedure"
MWI-39,
COMM ERROR 1 If a communication error is present in the communication line between combination
"Diagnosis
[B2201] meter and triple meter for 2 seconds or more.
Procedure"
MWI-41,
VEHICLE SPEED The abnormal vehicle speed signal is input from the ABS actuator and electric unit
"Diagnosis
[B2205] (control unit) for 2 seconds or more.
Procedure"
MWI-42,
ENGINE SPEED If ECM continuously transmits abnormal engine speed signals for 2 seconds or
"Diagnosis
[B2267] more.
Procedure"
MWI-43,
WATER TEMP If ECM continuously transmits abnormal engine coolant temperature signals for 60
"Diagnosis
[B2268] seconds or more.
Procedure"

< ECU DIAGNOSIS >
A
Reference Value INFOID:0000000004685210
VALUES ON THE DIAGNOSIS TOOL B

CONSULT-III MONITOR ITEM
C
Other than front wiper switch HI Off
FR WIPER HI
Front wiper switch HI On
Other than front wiper switch LO Off D
FR WIPER LOW
Front wiper switch LO On
Front washer switch OFF Off
FR WASHER SW E
Front washer switch ON On
Other than front wiper switch INT Off
FR WIPER INT
Front wiper switch INT On
F
Front wiper is not in STOP position Off
FR WIPER STOP
Front wiper is in STOP position On
Wiper intermittent dial G
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7
position
Other than turn signal switch RH Off
TURN SIGNAL R
Turn signal switch RH On H
Other than turn signal switch LH Off
TURN SIGNAL L
Turn signal switch LH On
I
Other than lighting switch 1ST and 2ND Off
TAIL LAMP SW
Lighting switch 1ST or 2ND On
Other than lighting switch HI Off J
HI BEAM SW
Lighting switch HI On
Other than lighting switch 2ND Off
HEAD LAMP SW 1 K
Lighting switch 2ND On
Other than lighting switch 2ND Off
HEAD LAMP SW 2
Lighting switch 2ND On L
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
M
Other than lighting switch AUTO Off
AUTO LIGHT SW
Lighting switch AUTO On
NOTE: WCS
FR FOG SW Off
The item is indicated, but not monitored.
Rear fog lamp switch OFF Off
RR FOG SW
Rear fog lamp switch ON On O
Driver door closed Off
DOOR SW-DR
Driver door opened On
P
Passenger door closed Off
DOOR SW-AS
Passenger door opened On
NOTE:
DOOR SW-RR Off
NOTE:
DOOR SW-RL Off

< ECU DIAGNOSIS >
Back door closed Off
DOOR SW-BK
Back door opened On
Other than door lock and unlock switch LOCK Off
CDL LOCK SW
Door lock and unlock switch LOCK On
Other than door lock and unlock switch UNLOCK Off
CDL UNLOCK SW
Door lock and unlock switch UNLOCK On
Other than driver door key cylinder LOCK position Off
KEY CYL LK-SW
Driver door key cylinder LOCK position On
Other than driver door key cylinder UNLOCK position Off
KEY CYL UN-SW
Driver door key cylinder UNLOCK position On
NOTE:
KEY CYL SW-TR Off
Hazard switch is OFF Off
HAZARD SW
Hazard switch is ON On
REAR DEF SW Rear window defogger switch OFF Off
NOTE:
At models with NAVI this item Rear window defogger switch ON On
is not monitored.
NOTE:
H/L WASH SW Off
NOTE:
TR CANCEL SW Off
Back door opener switch OFF Off
TR/BD OPEN SW
While the back door opener switch is turned ON On
NOTE:
TRNK/HAT MNTR Off
LOCK button of the Intelligent Key is not pressed Off
RKE-LOCK
LOCK button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-UNLOCK
UNLOCK button of the Intelligent Key is pressed On
NOTE:
RKE-TR/BD Off
PANIC button of the Intelligent Key is not pressed Off
RKE-PANIC
PANIC button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-P/W OPEN
UNLOCK button of the Intelligent Key is pressed and held On
LOCK/UNLOCK button of the Intelligent Key is not pressed and held simul-
Off
taneously
RKE-MODE CHG
LOCK/UNLOCK button of the Intelligent Key is pressed and held simulta-
On
neously
Bright outside of the vehicle Close to 5 V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0 V
Driver door request switch is not pressed Off
REQ SW -DR
Driver door request switch is pressed On
Passenger door request switch is not pressed Off
REQ SW -AS
Passenger door request switch is pressed On
NOTE:
REQ SW -RR Off

< ECU DIAGNOSIS >
A
NOTE:
REQ SW -RL Off
Back door request switch is not pressed Off
REQ SW -BD/TR B
Back door request switch is pressed On
Push-button ignition switch (push switch) is not pressed Off
PUSH SW
Push-button ignition switch (push switch) is pressed On C
Ignition switch in OFF or ACC position Off
IGN RLY2 -F/B
Ignition switch in ON position On
D
NOTE:
ACC RLY -F/B Off
CLUCH SW The clutch pedal is not depressed Off
NOTE: E
At A/T models this item is not The clutch pedal is depressed On
monitored.
Stop lamp switch 1 signal circuit is open Off F
BRAKE SW 1
Stop lamp switch 1 signal circuit is normal On
The brake pedal is not depressed Off
BRAKE SW 2 G
The brake pedal is depressed On
• Selector lever in P position (A/T models)
DETE/CANCL SW • The clutch pedal is depressed (M/T models without SynchroRev Match Off
NOTE: mode) H
At M/T models with SynchroR-
ev Match mode this item is not • Selector lever in any position other than P (A/T models)
monitored. • The clutch pedal is not depressed (M/T models without SynchroRev On
Match mode) I
• Selector lever in any position other than P and N (A/T models)
SFT PN/N SW • Control lever in any position other than neutral position (M/T models with Off
NOTE: SynchroRev Match mode)
At M/T models without Syn- J
chroRev Match mode this item • Selector lever in P or N position (A/T models)
is not monitored. • Control lever in neutral position (M/T models with SynchroRev Match On
mode)
K
Steering is unlocked Off
S/L -LOCK
Steering is locked On
Steering is locked Off L
S/L -UNLOCK
Steering is unlocked On
Ignition switch in OFF or ACC position Off
S/L RELAY-F/B M
Driver door is unlocked Off
UNLK SEN -DR
Driver door is locked On WCS
Push-button ignition switch (push-switch) is not pressed Off
PUSH SW -IPDM
Push-button ignition switch (push-switch) is pressed On
Ignition switch in OFF or ACC position Off O
IGN RLY1 -F/B
Selector lever in any position other than P Off
DETE SW -IPDM P
Selector lever in P position On
• Selector lever in any position other than P and N (A/T models)
Off
• The clutch pedal is not depressed (M/T models)
SFT PN -IPDM
• Selector lever in P or N position (A/T models)
On
• The clutch pedal is depressed (M/T models)

< ECU DIAGNOSIS >
Selector lever in any position other than P Off
SFT P -MET
Selector lever in P position On
Selector lever in any position other than N Off
SFT N -MET
Selector lever in N position On
Engine stopped Stop
While the engine stalls Stall
ENGINE STATE
At engine cranking Crank
Engine running Run
Steering is unlocked Off
S/L LOCK-IPDM
Steering is locked On
Steering is locked Off
S/L UNLK-IPDM
Steering is unlocked On
Steering lock system is not the LOCK condition and the changing condition
Off
from LOCK to UNLOCK
S/L RELAY-REQ
Steering lock system are not the LOCK condition or the changing condition
On
from LOCK to UNLOCK
Equivalent to speedom-
VEH SPEED 1 While driving
eter reading
Equivalent to speedom-
VEH SPEED 2 While driving
eter reading
Driver door is locked LOCK
DOOR STAT-DR Wait with selective UNLOCK operation (60 seconds) READY
Driver door is unlocked UNLOCK
Passenger door is locked LOCK
DOOR STAT-AS Wait with selective UNLOCK operation (60 seconds) READY
Passenger door is unlocked UNLOCK
Steering is locked Reset
ID OK FLAG
Steering is unlocked Set
The engine start is prohibited Reset
PRMT ENG STRT
The engine start is permitted Set
NOTE:
PRMT RKE STRT Reset
The Intelligent Key is not inserted into key slot Off
KEY SW -SLOT
The Intelligent Key is inserted into key slot On
Operation frequency of
RKE OPE COUN1 During the operation of the Intelligent Key
the Intelligent Key
NOTE:
RKE OPE COUN2 —
The key ID that the key slot receives is not recognized by any key ID regis-
Yet
tered to BCM.
CONFRM ID ALL
The key ID that the key slot receives is recognized by any key ID registered
Done
to BCM.
The key ID that the key slot receives is not recognized by the fourth key ID
Yet
registered to BCM.
CONFIRM ID4
The key ID that the key slot receives is recognized by the fourth key ID reg-
Done
istered to BCM.

< ECU DIAGNOSIS >
A
The key ID that the key slot receives is not recognized by the third key ID
Yet
registered to BCM.
CONFIRM ID3
The key ID that the key slot receives is recognized by the third key ID reg-
Done B
istered to BCM.
The key ID that the key slot receives is not recognized by the second key ID
Yet
registered to BCM.
CONFIRM ID2 C
The key ID that the key slot receives is recognized by the second key ID reg-
Done
istered to BCM.
The key ID that the key slot receives is not recognized by the first key ID reg-
Yet
istered to BCM. D
CONFIRM ID1
The key ID that the key slot receives is recognized by the first key ID regis-
Done
tered to BCM.
The ID of fourth Intelligent Key is not registered to BCM Yet E
TP 4
The ID of fourth Intelligent Key is registered to BCM Done
The ID of third Intelligent Key is not registered to BCM Yet
TP 3 F
The ID of third Intelligent Key is registered to BCM Done
The ID of second Intelligent Key is not registered to BCM Yet
TP 2
The ID of second Intelligent Key is registered to BCM Done G
The ID of first Intelligent Key is not registered to BCM Yet
TP 1
The ID of first Intelligent Key is registered to BCM Done
H
Air pressure of front LH
AIR PRESS FL Ignition switch ON (Only when the signal from the transmitter is received)
tire
Air pressure of front RH
AIR PRESS FR Ignition switch ON (Only when the signal from the transmitter is received) I
tire
Air pressure of rear RH
AIR PRESS RR Ignition switch ON (Only when the signal from the transmitter is received)
tire
J
Air pressure of rear LH
AIR PRESS RL Ignition switch ON (Only when the signal from the transmitter is received)
tire
ID of front LH tire transmitter is registered Done
ID REGST FL1 K
ID of front LH tire transmitter is not registered Yet
ID of front RH tire transmitter is registered Done
ID REGST FR1
ID of front RH tire transmitter is not registered Yet L
ID of rear RH tire transmitter is registered Done
ID REGST RR1
ID of rear RH tire transmitter is not registered Yet
M
ID of rear LH tire transmitter is registered Done
ID REGST RL1
ID of rear LH tire transmitter is not registered Yet
Tire pressure indicator OFF Off WCS
WARNING LAMP
Tire pressure indicator ON On
Tire pressure warning alarm is not sounding Off
BUZZER
Tire pressure warning alarm is sounding On O

< ECU DIAGNOSIS >
TERMINAL LAYOUT
JPMIA0062ZZ
PHYSICAL VALUES

< ECU DIAGNOSIS >
Terminal No. Description A

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
1 B
Ground Battery power supply Input Ignition switch OFF Battery voltage
(W)
2 P/W power supply
Ground Output Ignition switch OFF 12 V
(W) (BAT) C
3 P/W power supply
Ground Output Ignition switch ON 12 V
(Y) (RAP)
Interior room lamp battery saver is activated. D
0V
(Cuts the interior room lamp power supply)
4 Interior room lamp Interior room lamp battery saver is not acti-
Ground Output
(R) power supply vated.
12 V E
(Outputs the interior room lamp power sup-
ply)
UNLOCK (Actuator is acti-
12 V F
5 Passenger door UN- Passenger vated)
Ground Output
(G) LOCK door Other than UNLOCK (Ac-
0V
tuator is not activated)
LOCK G
12 V
8 All doors, fuel lid All doors, fuel (Actuator is activated)
Ground Output
(V) LOCK lid Other than LOCK
0V H
(Actuator is not activated)
UNLOCK
12 V
9 Driver door, fuel lid Driver door, (Actuator is activated)
Ground Output
(G) UNLOCK fuel lid Other than UNLOCK I
0V
(Actuator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(BR) J
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V K
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral L
position.
Push-button ignition
14
Ground switch illumination Output Tail lamp
(R) ON
ground
M
WCS
JSNIA0010GB
OFF (LOCK indicator is

15 Battery voltage
Ground ACC indicator lamp Output Ignition switch not illuminated)
(Y) O
ACC 0V

< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
+ – Output
Turn signal switch OFF 0V
17 Turn signal RH (Front Ignition switch

Ground Output
(W) and side) ON Turn signal switch RH
PKID0926E
6.5 V
18 Turn signal LH (Front Ignition switch

Ground Output
(O) and side) ON Turn signal switch LH
PKID0926E
6.5 V
19 Room lamp timer Interior room OFF 12 V

Ground Output
(V) control lamp ON 0V
20 Ignition switch
Ground Turn signal RH (Rear) Output
(V) ON Turn signal switch RH
PKID0926E
6.5 V
OPEN
(Back door opener actua- 12 V
23 tor is activated)
Ground Back door open Output Back door
(L) Other than OPEN
(Back door opener actua- 0V
tor is not activated)
24*1 OFF 0V
Ground Rear fog lamp Output Rear fog lamp
(O) ON 12 V
25 Ignition switch
Ground Turn signal LH (Rear) Output
(LG) ON Turn signal switch LH
PKID0926E
6.5 V
30 Luggage room ON 0V
Ground Luggage room lamp Output
(R) lamp OFF 12 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
When Intelligent Key is in

the passenger compart- C
ment
JMKIA0062GB
34 Luggage room anten- Ignition switch

D
Ground Output
(G) na (−) OFF
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
When Intelligent Key is in H

the passenger compart-
ment
JMKIA0062GB
I
35 Luggage room anten- Ignition switch
Ground Output
(R) na (+) OFF
J

K
ment
JMKIA0063GB
L
M
the antenna detection
area
WCS
When the back JMKIA0062GB
door request
38 Rear bumper anten-
Ground Output switch is oper-
(B) na (−)
ated with igni-
O
tion switch
OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output

area
When the back JMKIA0062GB

door request
39 Rear bumper anten-
(W) na (+)
ated with igni-
tion switch
OFF
area
JMKIA0063GB
47 Ignition relay (IPDM OFF or ACC 12 V

Ground Output Ignition switch
(V) E/R) control ON 0V
When selector lever is in P
Ignition switch 12 V
or N position
ON (A/T mod-
els) When selector lever is not
0V
52 in P or N position
Ground Starter relay control Output
(SB) When the clutch pedal is
Ignition switch Battery voltage
depressed
ON (M/T mod-
els) When the clutch pedal is
0V
not depressed
ON (Pressed) 0V
61 Back door request Back door re-

Ground Input
(W) switch quest switch OFF (Not pressed)
JPMIA0016GB
1.0 V
64 Intelligent Key warn- Intelligent Key Sounding 0V

Ground Output
(G) ing buzzer warning buzzer Not sounding 12 V
66 Back door OFF (Door close)

Ground Back door switch Input
(R) switch
JPMIA0011GB
11.8 V
ON (Door open) 0V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
Pressed 0V
B
67
Ground
Back door opener
Input
Back door C
(GR) switch opener switch Not pressed
D
JPMIA0011GB
11.8 V

the passenger compart- F
ment
JMKIA0062GB
G
72 Room antenna (−) Ignition switch
Ground Output
(L) (Center console) OFF
H
ment
I
JMKIA0063GB
When Intelligent Key is in K

the passenger compart-
ment
L
JMKIA0062GB
73 Room antenna (+) Ignition switch

Ground Output
(P) (Center console) OFF
M

in the passenger compart- WCS
ment
JMKIA0063GB
O

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output

area
When the pas- JMKIA0062GB

senger door re-
74 Passenger door an-
Ground Output quest switch is
(SB) tenna (−)
operated with
ignition switch
OFF
area
JMKIA0063GB

area
When the pas- JMKIA0062GB

senger door re-
75 Passenger door an-
Ground Output quest switch is
(BR) tenna (+)
operated with
ignition switch
OFF
area
JMKIA0063GB

area
When the driv- JMKIA0062GB

er door request
76 Driver door antenna
(V) (−)
ated with igni-
tion switch
OFF
area
JMKIA0063GB

< ECU DIAGNOSIS >
Input/ Condition
+ – Output

the antenna detection C
area
When the driv- JMKIA0062GB
77 Driver door antenna

er door request D
(LG) (+)
ated with igni-
tion switch
OFF E
area
F
JMKIA0063GB
Ignition switch is pressed Just after pressing ignition G

80 NATS antenna amp Input/
Ground During waiting while inserting the Intelli- switch. Pointer of tester should
(GR) (Built in key slot) Output
gent Key into the key slot. move.
Ignition switch is pressed Just after pressing ignition H
81 NATS antenna amp Input/
Ground During waiting while inserting the Intelli- switch. Pointer of tester should
(W) (Built in key slot) Output
gent Key into the key slot. move.
82 Ignition relay [Fuse OFF or ACC 0V I

(R) block (J/B)] control ON 12 V
During waiting
K
JMKIA0064GB
Remote keyless entry L
83 Input/
Ground receiver communica-
(GR) Output
tion
M
When operating either button on the Intelli-
gent Key
WCS
JMKIA0065GB

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
All switches OFF

(Wiper intermittent dial 4)
JPMIA0041GB
1.4 V
87 Combination switch Combination Rear fog lamp switch ON

Ground Input
(BR) INPUT 5 switch (Wiper intermittent dial 4)
JPMIA0038GB
1.3 V
Any of the conditions be-

low with all switches OFF
• Wiper intermittent dial 1
JPMIA0040GB
1.3 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
All switches OFF

(Wiper intermittent dial 4) C
JPMIA0041GB
1.4 V D
E
Lighting switch HI
F
JPMIA0036GB
88 Combination switch Combination 1.3 V

Ground Input G
(V) INPUT 3 switch
Lighting switch 2ND

H
JPMIA0037GB
I
1.3 V
J
K
JPMIA0040GB
1.3 V L
Push-button ig- Pressed 0V
89 Push-button ignition
Ground Input nition switch
(BR) switch (Push switch) Not pressed Battery voltage
(push switch) M
90 Input/
Ground CAN-L — —
(P) Output
91
Ground CAN-H
Input/
— —
WCS
(L) Output
OFF 0V
O
92 Key slot illumi- P

Ground Key slot illumination Output Blinking
(LG) nation
JPMIA0015GB
6.5 V
ON 12 V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
OFF (LOCK indicator is
93 Battery voltage
Ground ON indicator lamp Output Ignition switch not illuminated)
(V)
ON 0V
95 OFF 0V
Ground ACC relay control Output Ignition switch
(O) ACC or ON 12 V
Control device (De-
96*2 Ground tention switch) power Output — 12 V
(Y) supply
97 Steering lock condi- LOCK status 0V

Ground Input Steering lock
(L) tion No. 1 UNLOCK status 12 V
98 Steering lock condi- LOCK status 12 V

Ground Input Steering lock
(P) tion No. 2 UNLOCK status 0V
Selector lever P posi- P position 0V
tion switch (A/T mod- Selector lever
els) Any position other than P 12 V
99*3
(R)*2 Ground Clutch pedal position Input OFF (Clutch pedal is de-
0V
(BR)* 4 switch (M/T models Clutch pedal pressed)
without SynchroRev position switch ON (Clutch pedal is not
Match mode) Battery voltage
depressed)
ON (Pressed) 0V
Passenger
100 Passenger door re-
Ground Input door request
(GR) quest switch OFF (Not pressed)
switch
JPMIA0016GB
1.0 V
ON (Pressed) 0V
101 Driver door request Driver door re-

Ground Input
(Y) switch quest switch OFF (Not pressed)
JPMIA0016GB
1.0 V
102 Blower fan motor re- OFF or ACC 0V

(O) lay control ON 12 V
Remote keyless entry
103
Ground receiver power sup- Output Ignition switch OFF 12 V
(LG)
ply
106 Steering lock unit OFF or ACC 12 V

(W) power supply ON 0V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
All switches OFF C
JPMIA0041GB
1.4 V D
Turn signal switch LH
F
JPMIA0037GB
1.3 V
G
Combination
107 Combination switch switch
H
Ground Input Turn signal switch RH
(LG) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
Front wiper switch LO

K
JPMIA0038GB
1.3 V L
Front washer switch ON
WCS
JPMIA0039GB
1.3 V
O

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
All switches OFF

JPMIA0041GB
1.4 V
Lighting switch AUTO

JPMIA0038GB
108 Combination switch Combination 1.3 V

Ground Input
(R) INPUT 4 switch
Lighting switch 1ST

JPMIA0036GB
1.3 V

JPMIA0039GB
1.3 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
All switches OFF C
JPMIA0041GB
1.4 V D
Lighting switch PASS
F
JPMIA0037GB
1.3 V
G
Combination
H
Ground Input Lighting switch 2ND
(Y) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
Front wiper switch INT

K
JPMIA0038GB
1.3 V L
Front wiper switch HI
WCS
JPMIA0040GB
1.3 V
ON 0V O
P
110
Ground Hazard switch Input Hazard switch
(P) OFF
JPMIA0012GB
1.1 V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
LOCK status 12 V
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(Y) communication Output
JMKIA0066GB
For 15 seconds after UN-

12 V
LOCK
15 seconds or later after
0V
UNLOCK
When bright outside of the
Close to 5 V
113 Ignition switch vehicle
Ground Optical sensor Input
(O) ON When dark outside of the
Close to 0 V
vehicle
OFF (Clutch pedal is not
0V
114*5 Clutch interlock Clutch interlock depressed)
Ground Input
(R) switch switch ON (Clutch pedal is de-
Battery voltage
pressed)
116
Ground Stop lamp switch 1 Input — Battery voltage
(SB)
OFF (Brake pedal is not
0V
118 Stop lamp depressed)
Ground Stop lamp switch 2 Input
(P) switch ON (Brake pedal is de-
Battery voltage
pressed)
LOCK status
(Unlock sensor switch
Driver side door lock OFF)
119
Ground assembly (Unlock Input Driver door
(SB)
sensor)
JPMIA0012GB
1.1 V
UNLOCK status
(Unlock switch sensor 0V
ON)
When the Intelligent Key is inserted into key
12 V
121 slot
Ground Key slot switch Input
(R) When the Intelligent Key is not inserted into
0V
key slot
123 OFF or ACC 0V

Ground IGN feedback Input Ignition switch
(W) ON Battery voltage

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
124 Passenger door Passenger OFF (Door close) C

Ground Input
(LG) switch door switch
JPMIA0011GB
11.8 V D
ON (Door open) 0V
Rear window defogger

switch OFF F
130*6 Ground
Rear window defog-
Input
Ignition switch
(L) ger switch ON
JPMIA0012GB
1.1 V G
Rear window defogger
0V
switch ON
H
I
132 Power window switch Input/ Ignition switch ON
Ground
(Y) communication Output
J
JPMIA0013GB
10.2 V
Ignition switch OFF or ACC 12 V
K
ON (Tail lamps OFF) 9.5 V
NOTE:
The pulse width of this wave is
varied by the illumination bright-
L
ening/dimming level.
Push-button ig-
133 Push-button ignition
(G)
Ground
switch illumination
Output nition switch il- ON (Tail lamps ON) M
lumination
WCS
JPMIA0159GB
OFF 0V
O
134 LOCK indicator OFF Battery voltage
Ground LOCK indicator lamp Output
(GR) lamp ON 0V
137 Receiver and sensor P
Ground Input Ignition switch ON 0V
(P) ground
138 Receiver and sensor OFF 0V

(V) power supply ACC or ON 5.0 V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
Standby state
139 Tire pressure receiv- Input/ Ignition switch OCC3881D

Ground
(L) er communication Output ON
When receiving the signal

from the transmitter
OCC3880D
Selector lever P/N P or N position 12 V

Selector lever
position (A/T models) Except P and N positions 0V
140*7 Ground Park/neutral position Input Control lever in neutral po-
(G) Battery voltage
switch (M/T models Ignition switch sition
with SynchroRev ON Control lever in any posi-
Match mode) 0V
tion other than neutral
ON 0V
141 Security indica-

Ground Security indicator Output Blinking
(Y) tor
JPMIA0014GB
11.3 V
OFF 12 V
All switches OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(O) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switches OFF
0V
Front wiper switch HI
143 Combination switch Combination Any of the conditions be-
Ground Output
(P) OUTPUT 1 switch low with all switches OFF
• Wiper intermittent dial 6 JPMIA0032GB
• Wiper intermittent dial 7 10.7 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
All switches OFF
0V B
Front washer switch ON
144 Combination switch Combination
C
Ground Output
(G) OUTPUT 2 switch Any of the conditions be-
• Wiper intermittent dial 1 D
• Wiper intermittent dial 6 JPMIA0033GB
10.7 V
All switches OFF 0V
E
Front wiper switch INT
Front wiper switch LO
Combination F
145 Combination switch switch Lighting switch AUTO
Ground Output
(L) OUTPUT 3 (Wiper intermit-
tent dial 4)
G
Rear fog lamp switch ON
JPMIA0034GB
10.7 V
H
All switches OFF 0V
Lighting switch 2ND
Lighting switch PASS I
Combination
Ground Output
(SB) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH J
JPMIA0035GB
10.7 V
K
149 Tire pressure warning
Ground Input — 12 V
(W) check switch
150 Driver door OFF (Door close) M

Ground Driver door switch Input
(GR) switch
JPMIA0011GB
11.8 V
WCS
ON (Door open) 0V
151 Rear window defog- Rear window Active 0V

Ground Output O
(G) ger relay control defogger Not activated Battery voltage
• *1: For Canada
• *2: A/T models P
• *3: Except M/T models with SynchroRev Match mode
• *4: M/T models without SynchroRev Match mode
• *5: M/T models
• *6: Without NAVI
• *7: Except M/T models without SynchroRev Match mode

< ECU DIAGNOSIS >
Wiring Diagram - BCM - INFOID:0000000004685211
JCMWA3235GB

< ECU DIAGNOSIS >
WCS
JCMWA3236GB

< ECU DIAGNOSIS >
JCMWA3237GB

< ECU DIAGNOSIS >
WCS
JCMWA3238GB

< ECU DIAGNOSIS >
JCMWA3239GB

< ECU DIAGNOSIS >
WCS
JCMWA3240GB
P
Fail-safe INFOID:0000000004685212
FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC are detected.

< ECU DIAGNOSIS >
Display contents of CONSULT Fail-safe Cancellation

B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC
B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
When normal vehicle speed signals are received from ABS actua-
B2557: VEHICLE SPEED Inhibit steering lock
tor and electric unit (control unit) for 500 ms
500 ms after the following CAN signal communication status be-
comes consistent
B2560: STARTER CONT RELAY Inhibit engine cranking
• Starter control relay signal
• Starter relay status signal
500 ms after the following signal reception status becomes consis-
tent
B2601: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal
• P range signal (CAN)
5 seconds after the following BCM recognition conditions are ful-
filled
• Ignition switch is in the ON position
B2602: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal: Except P position (battery
voltage)
• Vehicle speed: 4 km/h (2.5 MPH) or more
500 ms after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
B2603: SHIFT POSI STATUS Inhibit steering lock • Selector lever P position switch signal: Except P position (battery
voltage)
• Selector lever P/N position signal: Except P and N positions (0 V)
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
B2604: PNP SW Inhibit steering lock age)
- P range signal or N range signal (CAN): ON
• Status 2
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Selector lever P/N position signal: Except P and N positions (0 V)
B2605: PNP SW Inhibit steering lock - Interlock/PNP switch signal (CAN): OFF
• Status 2
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
500 ms after the following CAN signal communication status be-
comes consistent
B2606: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)

< ECU DIAGNOSIS >
Display contents of CONSULT Fail-safe Cancellation
A
500 ms after the following CAN signal communication status has
becomes consistent
B2607: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal) B
500 ms after the following signal communication status becomes
consistent
B2608: STARTER RELAY Inhibit engine cranking
• Starter motor relay control signal
• Starter relay status signal (CAN)
C
When the following steering lock conditions agree
• Inhibit engine cranking • BCM steering lock control status
B2609: S/L STATUS D
• Inhibit steering lock • Steering lock condition No. 1 signal status
• Steering lock condition No. 2 signal status
500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage) E
B260A: IGNITION RELAY Inhibit engine cranking
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
Maintains the power supply When any of the following conditions are fulfilled
B260F: ENG STATE SIG LOST position attained at the time • Power position changes to ACC
F
of DTC detection • Receives engine status signal (CAN)
When any of the following conditions are fulfilled
• Steering lock unit status signal (CAN) is received normally G
• Inhibit engine cranking
B2612: S/L STATUS • The BCM steering lock control status matches the steering lock
• Inhibit steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
H
1 second after the starter motor relay control inside BCM becomes
B2617: STARTER RELAY CIRC Inhibit engine cranking
normal
1 second after the ignition relay (IPDM E/R) control inside BCM be-
B2618: BCM Inhibit engine cranking I
comes normal
1 second after the steering lock unit power supply output control in-
B2619: BCM Inhibit engine cranking
side BCM becomes normal
J
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
When any of the following BCM recognition conditions are fulfilled
• Status 1
- Clutch switch signal (CAN from ECM): ON
K
B26E8: CLUTCH SW Inhibit engine cranking - Clutch interlock switch signal: OFF (0 V)
• Status 2
- Clutch switch signal (CAN from ECM): OFF L
- Clutch interlock switch signal: ON (Battery voltage)
When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
• Inhibit engine cranking M
B26E9: S/L STATUS lowing conditions are fulfilled
• Inhibit steering lock
• Steering condition No. 1 signal: LOCK (0 V)
• Steering condition No. 2 signal: LOCK (Battery voltage)
HIGH FLASHER OPERATION WCS

BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating. O
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY RAIN SENSOR MALFUNCTION P
• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-
sor malfunction by rain sensor malfunction signal.
• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO
operation, BCM operates a fail-safe control.
NOTE:
If rain sensor malfunction is detected when ignition switch is turned OFF ⇒ ON and front wiper switch is INT
position, BCM operates a fail-safe control.

< ECU DIAGNOSIS >
DTC Inspection Priority Chart INFOID:0000000004685213
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3 • B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4 • B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E8: CLUTCH SW
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG

< ECU DIAGNOSIS >
Priority DTC
A
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL B
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL C
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL D
5 • C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
E
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
F
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR G
• C1727: [BATT VOLT LOW] RL
• C1734: CONTROL UNIT
• B2621: INSIDE ANTENNA
H
6 • B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA
DTC Index INFOID:0000000004685214 I
NOTE:
The details of time display are as follows.
J
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-17, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". K
Freeze Frame Data

Tire pressure
•Vehicle Speed Intelligent Key Refer-
CONSULT display Fail-safe monitor warning L
•Odo/Trip Meter warning lamp ON ence page
lamp ON
•Vehicle condition
No DTC is detected.
further testing — — — — — M
may be required.
U1000: CAN COMM CIRCUIT — — — — BCS-38
U1010: CONTROL UNIT (CAN) — — — — BCS-39 WCS
U0415: VEHICLE SPEED SIG — — — — BCS-40
B2013: ID DISCORD BCM-S/L × × — — SEC-50
O
B2014: CHAIN OF S/L-BCM × × — — SEC-51
B2190: NATS ANTENNA AMP × — — — SEC-42
B2191: DIFFERENCE OF KEY × — — — SEC-45 P
B2192: ID DISCORD BCM-ECM × — — — SEC-46
B2193: CHAIN OF BCM-ECM × — — — SEC-48
B2195: ANTI SCANNING × — — — SEC-49
B2553: IGNITION RELAY — × — — PCS-48
B2555: STOP LAMP — × — — SEC-54

< ECU DIAGNOSIS >
Freeze Frame Data
Tire pressure
•Vehicle Speed Intelligent Key Refer-
CONSULT display Fail-safe monitor warning
lamp ON
B2556: PUSH-BTN IGN SW — × × — SEC-56
B2557: VEHICLE SPEED × × × — SEC-58
B2560: STARTER CONT RELAY × × × — SEC-59
B2562: LOW VOLTAGE — × — — BCS-41
B2601: SHIFT POSITION × × × — SEC-60
B2602: SHIFT POSITION × × × — SEC-63
B2603: SHIFT POSI STATUS × × × — SEC-66
B2604: PNP SW × × × — SEC-69
B2605: PNP SW × × × — SEC-71
B2606: S/L RELAY × × × — SEC-73
B2607: S/L RELAY × × × — SEC-74
B2608: STARTER RELAY × × × — SEC-76
B2609: S/L STATUS × × × — SEC-78
B260A: IGNITION RELAY × × × — PCS-50
B260B: STEERING LOCK UNIT — × × — SEC-82
B260C: STEERING LOCK UNIT — × × — SEC-83
B260D: STEERING LOCK UNIT — × × — SEC-84
B260F: ENG STATE SIG LOST × × × — SEC-85
B2612: S/L STATUS × × × — SEC-90
B2614: ACC RELAY CIRC — × × — PCS-52
B2615: BLOWER RELAY CIRC — × × — PCS-55
B2616: IGN RELAY CIRC — × × — PCS-58
B2617: STARTER RELAY CIRC × × × — SEC-94
B2618: BCM × × × — PCS-61
B2619: BCM × × × — SEC-96
B261A: PUSH-BTN IGN SW — × × — PCS-62
× (Turn ON for 15
B261E: VEHICLE TYPE × × — SEC-97
seconds)
B2622: INSIDE ANTENNA — × — — DLK-55
B2623: INSIDE ANTENNA — × — — DLK-57
B26E8: CLUTCH SW × × × — SEC-86
× (Turn ON for 15
B26E9: S/L STATUS × × — SEC-88
seconds)
× (Turn ON for 15
B26EA: KEY REGISTRATION — × — SEC-89
seconds)
C1704: LOW PRESSURE FL — — — ×
C1705: LOW PRESSURE FR — — — ×
WT-15
C1706: LOW PRESSURE RR — — — ×
C1707: LOW PRESSURE RL — — — ×
C1708: [NO DATA] FL — — — ×
C1709: [NO DATA] FR — — — ×
WT-17
C1710: [NO DATA] RR — — — ×
C1711: [NO DATA] RL — — — ×

< ECU DIAGNOSIS >
Freeze Frame Data
Tire pressure
•Vehicle Speed Intelligent Key Refer- A
CONSULT display Fail-safe monitor warning
lamp ON
C1712: [CHECKSUM ERR] FL — — — × B
C1713: [CHECKSUM ERR] FR — — — ×
WT-20
C1714: [CHECKSUM ERR] RR — — — ×
C1715: [CHECKSUM ERR] RL — — — × C
C1716: [PRESSDATA ERR] FL — — — ×
C1717: [PRESSDATA ERR] FR — — — ×
WT-23 D
C1718: [PRESSDATA ERR] RR — — — ×
C1719: [PRESSDATA ERR] RL — — — ×
C1720: [CODE ERR] FL — — — × E
C1721: [CODE ERR] FR — — — ×
WT-25
C1722: [CODE ERR] RR — — — ×
F
C1723: [CODE ERR] RL — — — ×
C1724: [BATT VOLT LOW] FL — — — ×
C1725: [BATT VOLT LOW] FR — — — × G
WT-28
C1726: [BATT VOLT LOW] RR — — — ×
C1727: [BATT VOLT LOW] RL — — — ×
H
C1729: VHCL SPEED SIG ERR — — — × WT-31
C1734: CONTROL UNIT — — — × WT-33
WCS

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
1.CHECK PARKING BRAKE WARNING LAMP

1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
When parking brake is applied : ON

When parking brake is released : OFF
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform check for the parking brake switch signal circuit. Refer to MWI-52, "Diagnosis Procedure".
YES >> GO TO 3.
3.CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to MWI-52, "Component Inspection".
NO >> Replace parking brake switch. Refer to PB-6, "Exploded View".

THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
A
Light reminder warning chime does not sound even though headlamp is illuminated. B
1.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION C

Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
D
YES >> GO TO 2.
NO >> Refer to EXL-152, "Diagnosis Procedure".
2.CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT E
Perform the check for the driver side door switch signal circuit. Refer to DLK-60, "Diagnosis Procedure".
YES >> GO TO 3. F
3.CHECK DRIVER SIDE DOOR SWITCH G
Perform a unit check for the driver side door switch. Refer to DLK-61, "Component Inspection".
YES >> Replace BCM. Refer to BCS-84, "Removal and Installation". H
NO >> Replace driver side door switch. Refer to DLK-233, "Removal and Installation".
WCS

THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
• Seat belt reminder warning does not sound.

• Seat belt reminder warning sounds continuously.
1.CHECK SEAT BELT WARNING LAMP

1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.
Seat belt fastened : OFF

Seat belt not fastened : ON
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK BCM OUTPUT SIGNAL
Check if the light reminder warning chime is activated by performing BCM active test. Refer to WCS-16,
"BUZZER : CONSULT-III Function (BCM - BUZZER)".
NO >> GO TO 3.
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to WCS-11,
"CONSULT-III Function (METER/M&A)".
Buzzer active condition : On

Buzzer non-active condition : Off
NO >> Replace BCM. Refer to BCS-84, "Removal and Installation".
4.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT
Perform the check for the seat belt buckle switch (driver side) circuit. Refer to WCS-21,
"Diagnosis Procedure".
YES >> GO TO 5.
5.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to WCS-22, "Component Inspection".
NO >> Replace seat belt buckle (driver side). Refer to SB-8, "SEAT BELT BUCKLE : Removal and Instal-
lation".

PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000004688884
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser- G
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS H
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury. I
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Precaution for Battery Service INFOID:0000000004749261 J
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the K
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
L
WCS

Warning Chime System: Section

Uploaded by

Copyright:

Available Formats

Warning Chime System: Section

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Warning Chime System: Section

Uploaded by

Copyright:

Available Formats

DRIVER INFORMATION & MULTIMEDIA

Revision: 2008 October WCS-1 2009 370Z

ECU DIAGNOSIS ........................................ 27 THE LIGHT REMINDER WARNING DOES

Revision: 2008 October WCS-2 2009 370Z

Revision: 2008 October WCS-3 2009 370Z

Revision: 2008 October WCS-4 2009 370Z

Warning functions Signal name

Revision: 2008 October WCS-5 2009 370Z

ABS actuator and electric unit (con-

WARNING CHIME SYSTEM : Component Description INFOID:0000000004536920

LIGHT REMINDER WARNING CHIME

Revision: 2008 October WCS-6 2009 370Z

ABS actuator and electric unit (con-

Revision: 2008 October WCS-7 2009 370Z

SEAT BELT WARNING CHIME

SEAT BELT WARNING CHIME : System Description INFOID:0000000004536926

Revision: 2008 October WCS-8 2009 370Z

ABS actuator and electric unit (con-

Revision: 2008 October WCS-9 2009 370Z

ABS actuator and electric unit (con-

PARKING BRAKE RELEASE WARNING CHIME : Component Description INFOID:0000000004536932

Revision: 2008 October WCS-10 2009 370Z

CONSULT-III APPLICATION ITEMS B

System Diagnosis mode Description C

SELF DIAG RESULT

Revision: 2008 October WCS-11 2009 370Z

Revision: 2008 October WCS-12 2009 370Z

Display item Description

Display item Description

Revision: 2008 October WCS-13 2009 370Z

Revision: 2008 October WCS-14 2009 370Z

FREEZE FRAME DATA (FFD)

Revision: 2008 October WCS-15 2009 370Z

CONSULT screen item Indication/Unit Description

CONSULT-III APPLICATION ITEMS

Test item Diagnosis mode Description

Revision: 2008 October WCS-16 2009 370Z

Revision: 2008 October WCS-17 2009 370Z

Power source Fuse No.

1.CHECK FUSE AND FUSIBLE LINK

Revision: 2008 October WCS-18 2009 370Z

Signal name Fuse and fusible link No. A

Revision: 2008 October WCS-19 2009 370Z

1.CHECK OPERATION OF METER BUZZER

1.CHECK POWER SUPPLY OF COMBINATION METER

Revision: 2008 October WCS-20 2009 370Z

1.CHECK COMBINATION METER INPUT SIGNAL C

>> INSPECTION END

1.CHECK COMBINATION METER INPUT SIGNAL

2.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT

Revision: 2008 October WCS-21 2009 370Z

1.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)

Revision: 2008 October WCS-22 2009 370Z

Revision: 2008 October WCS-23 2009 370Z

Revision: 2008 October WCS-24 2009 370Z

Revision: 2008 October WCS-25 2009 370Z

Revision: 2008 October WCS-26 2009 370Z

VALUES ON THE DIAGNOSIS TOOL

Ignition switch ABS warning lamp ON On J