Warning Chime System: Section
Warning Chime System: Section
WCS
A
B
SECTION
WARNING CHIME SYSTEM C
E
CONTENTS
PRECAUTION ............................................... 3 PARKING BRAKE RELEASE WARNING CHIME F
: System Description ................................................. 8
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System DIAGNOSIS SYSTEM (COMBINATION
G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- METER) .............................................................. 9
SIONER" ................................................................... 3 Description ................................................................ 9
CONSULT Function (METER/M&A) ........................10
SYSTEM DESCRIPTION .............................. 4 H
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
COMPONENT PARTS ........................................ 4 GENT KEY SYSTEM) ....................................... 13
Component Parts Location ........................................ 4 I
Component Description ............................................. 5 COMMON ITEM .........................................................13
COMMON ITEM : CONSULT Function (BCM -
SYSTEM .............................................................. 6 COMMON ITEM) .....................................................13
J
WARNING CHIME SYSTEM ....................................... 6 BUZZER .....................................................................14
WARNING CHIME SYSTEM : System Diagram ...... 6 BUZZER : CONSULT Function (BCM - BUZZER)....14
WARNING CHIME SYSTEM : System Description
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- K
...... 6
TELLIGENT KEY SYSTEM) ............................. 15
LIGHT REMINDER WARNING CHIME ....................... 6
LIGHT REMINDER WARNING CHIME : System COMMON ITEM .........................................................15 L
Diagram ..................................................................... 6 COMMON ITEM : CONSULT Function (BCM -
LIGHT REMINDER WARNING CHIME : System COMMON ITEM) .....................................................15
Description ................................................................ 6
BUZZER .....................................................................16 M
SEAT BELT WARNING CHIME .................................. 7 BUZZER : CONSULT Function (BCM - BUZZER)....16
SEAT BELT WARNING CHIME : System Diagram
...... 7 ECU DIAGNOSIS INFORMATION .............. 17 WCS
SEAT BELT WARNING CHIME : System Descrip-
BCM, COMBINATION METER ......................... 17
tion ............................................................................ 7
List of ECU Reference .............................................17
KEY WARNING CHIME (WITHOUT INTELLIGENT O
KEY) ............................................................................. 7 WIRING DIAGRAM ...................................... 18
KEY WARNING CHIME (WITHOUT INTELLI- WARNING CHIME SYSTEM ............................. 18
GENT KEY) : System Diagram ................................. 7 Wiring Diagram ........................................................18 P
KEY WARNING CHIME (WITHOUT INTELLI-
GENT KEY) : System Description ............................. 7 BASIC INSPECTION ................................... 24
PARKING BRAKE RELEASE WARNING CHIME ...... 8 DIAGNOSIS AND REPAIR WORKFLOW ........ 24
PARKING BRAKE RELEASE WARNING CHIME Work Flow ................................................................24
: System Diagram ...................................................... 8
DTC/CIRCUIT DIAGNOSIS ......................... 26
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- H
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery and wait at least three minutes before performing any service.
WCS
AWNIA3365ZZ
1. Combination meter 2. Combination switch (lighting and turn 3. Key switch (without Intelligent Key A
signal switch) system)
4. Push-button ignition switch (with Intel- 5. Seat belt buckle switch LH 6. Front door switch LH
ligent Key system)
B
7. BCM 8. ABS actuator and electric unit (control Parking brake switch
9.
(view with instrument panel removed) unit) (view with center console removed)
Unit Description
D
• Judges whether the parking brake is released using the vehicle speed signal and the parking
brake switch signal, and sounds the buzzer if necessary.
Combination meter • Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
BCM with CAN communication line. E
• Receives a buzzer output signal from BCM with CAN communication line.
Lighting switch Transmits lighting switch status signal to the BCM.
BCM Transmits signals provided by various units to the combination meter with CAN communication line. F
Front door switch LH Transmits door switch signal to BCM.
Key switch Transmits key switch signal to BCM.
G
Push-button ignition switch Provides ignition switch status to the BCM
Seat belt buckle switch LH Transmits seat belt buckle switch LH signal to the combination meter.
Parking brake switch Transmits parking brake switch signal to the combination meter. H
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter with CAN communication line.
(control unit)
I
WCS
AWNIA2651GB
DESCRIPTION
• The buzzer for warning chime system is installed in the combination meter.
• The buzzer sounds when the combination meter receives a buzzer output signal from the BCM.
• The BCM receives signals from various units and transmits a buzzer output signal to the combination meter
with CAN communication line if it judges that the warning buzzer should be activated.
LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000011539235
AWNIA2539GB
DESCRIPTION
With ignition switch in OFF or ACC position, driver door open, and lighting switch in parking lamp or headlamp
position, the light warning chime will sound.
• BCM detects ignition switch in OFF or ACC position, front door switch LH ON, and lighting switch in parking
lamp or headlamp position, and then transmits buzzer output signal (light reminder warning chime) to combi-
nation meter with CAN communication line.
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled
• Lighting switch is in parking lamp or headlamp position
• Ignition switch is in OFF or ACC
• Front door switch LH is ON
AWNIA2652GB F
G
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi-
mately 6 seconds. H
• BCM receives seat belt buckle switch signal from combination meter with CAN communication line.
• BCM detects ignition switch turned ON and seat belt buckle switch LH ON, and then transmits buzzer output
signal (seat belt warning chime) to combination meter with CAN communication line.
I
• When combination meter receives buzzer output signal (seat belt warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
J
If all of the following conditions are fulfilled
• Ignition switch OFF→ON
• Seat belt buckle switch LH is ON (driver seat belt not fastened)
K
WARNING CANCEL CONDITIONS
Cancels the warning if any of the following conditions is fulfilled.
• Ignition switch OFF L
• Seat belt buckle switch LH is OFF (driver seat belt fastened)
KEY WARNING CHIME (WITHOUT INTELLIGENT KEY)
M
KEY WARNING CHIME (WITHOUT INTELLIGENT KEY) : System Diagram
INFOID:0000000011539239
WCS
P
AWNIA2361GB
With the key inserted into the key switch, and the ignition switch in the OFF or ACC position, when driver's
door is opened, the warning chime will sound.
Revision: December 2014 WCS-7 2015 Sentra NAM
SYSTEM
< SYSTEM DESCRIPTION >
• BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with
CAN communication line.
• When combination meter receives key warning signal, it sounds warning chime.
PARKING BRAKE RELEASE WARNING CHIME
PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000011539241
AWNIA0263GB
DESCRIPTION
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication line.
• The combination meter judges whether the parking brake is released using the parking brake switch signal
from the parking brake switch, and sounds the warning buzzer if necessary.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled:
• Vehicle speed is approximately 7 km/h (4.3 MPH) or higher
• Parking brake switch ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled:
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
JSNIA5050ZZ
AWNIA2863GB
I
WCS
AWNIA2863GB
O
NOTE:
• Check the following items when the self-diagnosis mode of the combination meter does not start.
Replace combination meter if the following items are normal. P
- Combination meter power supply and ground circuit.
- Steering switch signal circuit and steering switch.
• If any of the dots are not displayed, replace combination meter.
AWNIA2862GB
NOTE:
• If any of the meters or gauges is not activated, replace combination meter.
• The figure is reference.
CONSULT Function (METER/M&A) INFOID:0000000011897890
APPLICATION ITEMS
CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.
MAIN
Display item [Unit] Description
SIGNALS
SPEED METER
X Displays the value of vehicle speed signal.
[km/h] or [mph]
SPEED OUTPUT Displays the value of vehicle speed signal, which is transmitted to each unit with
X
[km/h] or [mph] CAN communication.
ODO OUTPUT Displays odometer signal value transmitted to other units via CAN communica-
[km/h or mph] tion.
TACHO METER
X Displays the value of engine speed signal, which is input from ECM.
[rpm]
FUEL METER
X Displays the fuel level.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
[°C] or [°F]
ABS W/L
Displays [ON/OFF] condition of ABS warning indicator
[ON/OFF]
SLIP IND
Displays [ON/OFF] condition of SLIP indicator lamp.
[ON/OFF]
WARNING HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “WARNING HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO WARNING HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• WARNING HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
WORK SUPPORT
SYSTEM APPLICATION
G
BCM can perform the following functions.
I
System Sub System
ECU Identification
Configuration
Work support
Data Monitor
J
Active Test
K
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × L
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
M
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
Air conditioner AIR CONDITIONER × WCS
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
BCM BCM × × × × × O
Immobilizer IMMU × × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
P
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
DATA MONITOR
ACTIVE TEST
SYSTEM APPLICATION
G
BCM can perform the following functions.
I
System Sub System
ECU Identification
Configuration
Work support
Data Monitor
J
Active Test
K
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × L
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
M
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × WCS
Air conditioner AIR CONDITIONER ×
Combination switch COMB SW ×
BCM BCM × × × × × O
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
P
Trunk open TRUNK ×
RAP system RETAINED PWR × ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×
DATA MONITOR
ACTIVE TEST
ECU Reference
C
BCS-29, "Reference Value"
WCS
ABNWA2739GB
WCS
ABNIA5773GB
ABNIA5770GB
WCS
ABNIA5771GB
AANIA1339GB
WCS
ABNIA5774GB
OVERALL SEQUENCE
JSNIA4485GB
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
Connect CONSULT and perform self-diagnosis. Refer to MWI-26, "DTC Index".
>> GO TO 5. C
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE: D
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6. E
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally. F
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 1. G
WCS
1.CHECK FUSES
Check that the following fuses are not blown.
Combination meter
Continuity
Connector Terminal
21 Ground
M24 22 Yes
23
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connector.
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure INFOID:0000000011897899
WCS
Regarding Wiring Diagram information, refer to BCS-115, "Wiring Diagram".
O
1.CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
P
BCM
Ground Continuity
Connector Terminal
M20 65 — Yes
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
• The buzzer for warning chime system is installed in the combination meter. B
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000011539255
C
1.CHECK OPERATION OF METER BUZZER
1. Select BUZZER of BCM on CONSULT.
2. Perform LIGHT WARN ALM of Active Test. D
Does meter buzzer activate?
YES >> Inspection End.
NO >> Refer to WCS-29, "Diagnosis Procedure". E
Select the Data Monitor for the METER/M&A and check the BUZZER monitor value.
G
Monitor Item Condition Status
Under the condition of the Buzzer input ON
BUZZER H
Except above OFF
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-77, "Removal and Installation". I
NO >> Replace BCM. Refer to BCS-76, "Removal and Installation" (with Intelligent Key) or BCS-133,
"Removal and Installation" (without Intelligent Key).
J
WCS
Transmits a seat belt buckle switch LH (driver seat) signal to the combination meter.
Component Function Check INFOID:0000000011539258
Combination meter
Ground Continuity
Connector Terminal
M24 9 — No
Is the inspection result normal?
WCS
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
D
1.CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake. E
Check the parking brake switch signal circuit. Refer to MWI-60, "Diagnosis Procedure".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK PARKING BRAKE SWITCH J
Check the parking brake switch. Refer to MWI-61, "Component Inspection".
Is the inspection result normal?
K
YES >> Replace combination meter. Refer to MWI-77, "Removal and Installation".
NO >> Replace parking brake switch. Refer to PB-7, "Exploded View".
WCS
Light reminder warning chime does not sound even though headlamp is illuminated. B
Diagnosis Procedure INFOID:0000000011539267
D
Monitor Item Condition Status
Under the condition of buzzer input ON
BUZZER
Except above OFF E
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-77, "Removal and Installation".
NO >> GO TO 2. F
2.CHECK FRONT DOOR SWITCH LH SIGNAL CIRCUIT
Check the front door switch LH signal circuit. Refer to DLK-109, "Diagnosis Procedure" (with Intelligent Key G
system) or DLK-260, "Diagnosis Procedure" (without Intelligent Key system).
Is the inspection result normal?
YES >> GO TO 3. H
NO >> Repair or replace harness or connector.
3.CHECK FRONT DOOR SWITCH LH
Check front door switch LH. Refer to DLK-110, "Component Inspection" (with Intelligent Key system) or DLK- I
262, "Component Inspection" (without Intelligent Key system).
Is the inspection result normal?
YES >> Replace the BCM. Refer to BCS-76, "Removal and Installation" (with Intelligent Key system) or J
BCS-133, "Removal and Installation" (without Intelligent Key system).
NO >> Replace the front door switch LH. Refer to DLK-201, "Removal and Installation" (with Intelligent
Key system) or DLK-348, "Removal and Installation" (without Intelligent Key system). K
WCS
The key warning chime does not sound, when all of the following conditions are fulfilled.
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (driver side door switch ON)
Diagnosis Procedure INFOID:0000000011539269