Interior Lighting System: Section

DRIVER CONTROLS
INL
A
B
SECTION
INTERIOR LIGHTING SYSTEM C
E
CONTENTS
WITH POWER DOOR LOCKS BATTERY SAVER OUTPUT/POWER SUP- F
PLY CIRCUIT .................................................... 16
BASIC INSPECTION .................................... 3 Description ...............................................................16
Component Function Check ....................................16 G
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 Diagnosis Procedure ...............................................16
Work Flow ................................................................. 3
INTERIOR ROOM LAMP CONTROL CIRCUIT
SYSTEM DESCRIPTION .............................. 6 ... 18
H
INTERIOR ROOM LAMP CONTROL SYSTEM Description ...............................................................18

..... 6 Component Function Check ....................................18
Diagnosis Procedure ...............................................18 I
System Diagram ........................................................ 6
System Description ................................................... 6 CARGO LAMP CONTROL CIRCUIT ................ 20
Component Parts Location ........................................ 7 Description ...............................................................20
Component Description ............................................. 8 J
Diagnosis Procedure ...............................................20
ILLUMINATION CONTROL SYSTEM ................. 9 Component Inspection .............................................22
System Diagram ........................................................ 9 IGNITION KEYHOLE ILLUMINATION CON- K
System Description ................................................... 9 TROL CIRCUIT ................................................. 24
Component Parts Location ...................................... 10
Description ...............................................................24
Component Description ........................................... 10
Component Function Check ....................................24 INL
DIAGNOSIS SYSTEM (BCM) ............................11 Diagnosis Procedure ...............................................24
COMMON ITEM ......................................................... 11 ECU DIAGNOSIS INFORMATION .............. 26

M
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ..................................................... 11
BCM (BODY CONTROL MODULE) ................. 26
Reference Value ......................................................26
INT LAMP .................................................................. 11 Terminal Layout .......................................................29 N
INT LAMP : CONSULT Function (BCM - INT Physical Values .......................................................29
LAMP) ..................................................................... 12 Fail Safe ..................................................................34
DTC Inspection Priority Chart ...............................34
BATTERY SAVER ..................................................... 12 O
DTC Index ...............................................................35
BATTERY SAVER : CONSULT Function (BCM -
BATTERY SAVER) ................................................. 12 WIRING DIAGRAM ...................................... 37
P
DTC/CIRCUIT DIAGNOSIS ......................... 14 INTERIOR ROOM LAMP .................................. 37
Wiring Diagram - With Power Door Lock System ....37
POWER SUPPLY AND GROUND CIRCUIT ......14
ILLUMINATION ................................................. 50
BCM ........................................................................... 14 Wiring Diagram ........................................................50
BCM : Diagnosis Procedure .................................... 14
SYMPTOM DIAGNOSIS .............................. 60
Revision: May 2014 INL-1 2014 Frontier

INTERIOR LIGHTING SYSTEM SYMPTOMS ... 60 INTERIOR ROOM LAMP ................................... 78
Symptom Table ...................................................... 60 Diagnosis Procedure ............................................... 78
Component Inspection (Door Switch) ..................... 79
PRECAUTION ............................................. 61
CARGO LAMP CONTROL CIRCUIT ................ 80
PRECAUTIONS ................................................. 61 Description .............................................................. 80
Precaution for Supplemental Restraint System Diagnosis Procedure ............................................... 80
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Component Inspection ............................................ 82
SIONER" ................................................................. 61
Precaution for Work ................................................ 61 ECU DIAGNOSIS INFORMATION ............. 84
PREPARATION ........................................... 62 BCM (BODY CONTROL MODULE) .................. 84
Reference Value ..................................................... 84
PREPARATION ................................................. 62 Terminal Layout ...................................................... 87
Special Service Tool ............................................... 62 Physical Values ....................................................... 87
Fail Safe ................................................................. 92
REMOVAL AND INSTALLATION ............... 63 DTC Inspection Priority Chart ............................... 92
INTERIOR ROOM LAMP ................................... 63 DTC Index .............................................................. 93
Removal and Installation ........................................ 63 WIRING DIAGRAM .................................... 95
ILLUMINATION .................................................. 66 INTERIOR ROOM LAMP ................................... 95
Removal and Installation ........................................ 66
Wiring Diagram - Without Power Door Lock Sys-
SERVICE DATA AND SPECIFICATIONS tem .......................................................................... 95
(SDS) ........................................................... 67 ILLUMINATION ................................................ 104
Wiring Diagram ..................................................... 104
BULB SPECIFICATIONS .................................. 67
Bulb Specifications ................................................. 67 SYMPTOM DIAGNOSIS ........................... 114
WITHOUT POWER DOOR LOCKS
INTERIOR LIGHTING SYSTEM SYMPTOMS.. 114
BASIC INSPECTION ................................... 68 Symptom Table ..................................................... 114
DIAGNOSIS AND REPAIR WORKFLOW ......... 68 PRECAUTION ........................................... 115

Work Flow ............................................................... 68
PRECAUTIONS ................................................ 115
SYSTEM DESCRIPTION ............................ 71 Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
INTERIOR ROOM LAMP ................................... 71 SIONER" ............................................................... 115
System Diagram ..................................................... 71 Precaution for Work .............................................. 115
System Description ................................................. 71
Component Parts Location ..................................... 72 PREPARATION ......................................... 116
Component Description .......................................... 72
PREPARATION ................................................ 116
ILLUMINATION CONTROL SYSTEM ............... 74 Special Service Tool ............................................. 116
System Diagram ..................................................... 74
System Description ................................................. 74 REMOVAL AND INSTALLATION ............. 117
Component Parts Location ..................................... 75
Component Description .......................................... 75 INTERIOR ROOM LAMP .................................. 117
Removal and Installation ....................................... 117
DIAGNOSIS SYSTEM (BCM) ............................ 76
ILLUMINATION ................................................ 120
COMMON ITEM ........................................................ 76 Removal and Installation ....................................... 120
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) .................................................... 76 SERVICE DATA AND SPECIFICATIONS
(SDS) ......................................................... 121
INT LAMP .................................................................. 76
INT LAMP : CONSULT Function (BCM - INT BULB SPECIFICATIONS ................................. 121
LAMP) ..................................................................... 77 Bulb Specifications ................................................ 121
DTC/CIRCUIT DIAGNOSIS ......................... 78

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [WITH POWER DOOR LOCKS]
BASIC INSPECTION A
Work Flow INFOID:0000000009480123
B
OVERALL SEQUENCE
C
INL
P
AWLIA1837GB

DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Find out what the customer's concerns are.
>> GO TO 2
2.SYMPTOM CHECK
Verify the symptom from the customer's information.
>> GO TO 3
3.BASIC INSPECTION
Check the operation of each part. Check that any concerns occur other than those mentioned in the customer
interview.
>> GO TO 4
4.SELF-DIAGNOSIS WITH CONSULT
Perform the self-diagnosis with CONSULT. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5
NO >> GO TO 6
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9
6.FAIL-SAFE ACTIVATION CHECK
Determine if the customer’s concern is related to fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7
NO >> GO TO 8
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system in which the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform the self-diagnosis with CONSULT. Verify that no DTCs are detected. Erase all DTCs detected prior to
the repair. Verify that DTC is not detected again.
YES >> GO TO 5

NO >> GO TO 11
11.REPAIR CHECK (OPERATION CHECK) A
Check the operation of each part.

Does it operate normally? B
YES >> Inspection End
NO >> GO TO 3
C
INL

INTERIOR ROOM LAMP CONTROL SYSTEM
< SYSTEM DESCRIPTION > [WITH POWER DOOR LOCKS]
SYSTEM DESCRIPTION
System Diagram INFOID:0000000009480124
AWLIA2277GB
System Description INFOID:0000000009480125
OUTLINE
• Front room/map lamp and room lamp 2nd row are controlled by the interior room lamp timer control function
of the BCM.
• Cargo lamp is controlled by the cargo lamp control function of the BCM.
The timer control functions of the BCM activate based on inputs from the remote keyless entry receiver, the
key cylinder lock/unlock switch, the door switches, the key switch and the power window and door lock/unlock
switches.
ROOM LAMP TIMER OPERATION
When the interior room lamp switch is in the DOOR position and when all conditions below are met, the BCM
begins timer control (maximum 30 seconds) for interior room lamp ON/OFF.
• When the front door LH is unlocked [with main power window and door lock/unlock switch, or front door lock
assembly LH (key cylinder switch)].
• When a door opens → closes.
Timer control is cancelled under the following conditions.
• When the front door LH is locked [with main power window and door lock/unlock switch, or front door lock
assembly LH (key cylinder switch)].
• A door is opened (door switch turns ON).
• The ignition switch is placed the ON position.
Interior lamp operational settings can be changed with the CONSULT.
INTERIOR LAMP BATTERY SAVER CONTROL

If an interior lamp is left ON and does not turn OFF even when the doors are closed, the BCM turns off power
to the interior lamps automatically to save the battery 10 minutes after the ignition switch is turned OFF. A
The BCM controls power and ground to all interior lamps.
After the battery saver system turns the lamps OFF, the lamps will illuminate again when
• a signal is received from a main power window and door lock/unlock switch, or when the front door lock
B
assembly LH (key cylinder switch) is locked or unlocked
• a door is opened or closed
The interior lamp battery saver control time period can be changed with the CONSULT.
C
Component Parts Location INFOID:0000000009480126
INL
ABLIA2842ZZ
1. BCM M18, M19, M20 (view with lower 2. Key switch M27 3. Cargo lamp switch M71 P
instrument panel LH removed)
4. Front door switch LH B8 (crew cab) 5. Rear door switch LH B18 (crew cab) 6. Front door switch LH D213 (king cab)
Front door switch RH B108 (crew cab) Rear door switch RH B116 (crew cab) Front door switch RH D314 (king cab)
7. Rear door switch upper LH D211 (king 8. Rear door switch lower LH D212 (king 9. Cargo lamp B161
cab) cab)
Rear door switch upper RH D312 (king Rear door switch lower RH D313 (king
cab) cab)

10. Room lamp 2nd row R10 11. Front room/map lamp assembly R9 12. Vanity lamp LH B80 (if equipped)
Vanity lamp RH B81 (if equipped)
13. Ignition keyhole illumination M150 (if
equipped)
Component Description INFOID:0000000009480127
Part name Description

Provides power and ground and controls timer functions for the
BCM
interior room lamps and cargo lamp.
Key switch Provides key in ignition status to the BCM.
Door switches Provides door OPEN/CLOSED status to the BCM.
Cargo lamp switch Provides cargo lamp ON/OFF request to the BCM.
Main power window and door lock/unlock switch
Provides door lock/unlock position switch status to the BCM.
Power window and door lock/unlock switch RH
Front door lock assembly LH (key cylinder switch) Provides door lock/unlock status to the BCM.

ILLUMINATION CONTROL SYSTEM
A
AWLIA1754GB F
G
The illumination lamps operation is dependent upon the position of the combination switch (lighting and turn
signal switch). When the combination switch (lighting and turn signal switch) is placed in the 1ST or 2ND posi-
tion (or if the auto light system is activated) the BCM (body control module) receives input requesting the park- H
ing lamps to illuminate. This input is communicated to the IPDM E/R (intelligent power distribution module
engine room) via the CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls
the tail lamp relay coil. When energized, this relay directs power to the parking and illumination lamps, which
then illuminate. I
BATTERY SAVER CONTROL
When the combination switch (lighting and turn signal switch) is in the 1ST or 2ND position and the ignition
switch is turned from ON or ACC to OFF, the battery saver control feature is activated. Under this condition, J
the illumination lamps remain illuminated for 10 minutes unless the combination switch (lighting and turn signal
switch) position is changed. If the combination switch (lighting and turn signal switch) position is changed, then
the illumination lamps are turned off after a 30 second delay. When the combination switch (lighting and turn K
signal switch) is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after illumination
lamps have been turned off by the battery saver control, the illumination lamps illuminate again.
INL

WKIA5029E
1. IPDM E/R E122, E124 2. Combination switch (lighting and turn 3. Combination meter M24
signal switch) M28
4. Illumination control switch (built into 5. BCM M18, M20 (view with lower instru-
combination meter) ment panel LH removed)

The BCM monitors the lighting switch position with the combina-
BCM tion switch reading function. The BCM requests, via CAN com-
munication, that the IPDM E/R activate the tail lamp relay.
The IPDM E/R activates the tail lamp relay based on inputs re-
IPDM E/R
ceived from the BCM via the CAN communication network.
The illumination control switch is a part of the combination meter.
The combination meter controls illumination intensity by varying
Combination meter (illumination control switch)
ground to the illumination lamps based on the illumination control
switch position.
The combination switch (lighting and turn signal switch) provides
Combination switch (lighting and turn signal switch)
input to the BCM about the lighting switch position.

DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010228001
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Direct Diagnostic Mode Description
ECU Identification The BCM part number is displayed.
D
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components. E
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM. F
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
G
BCM can perform the following functions.
Direct Diagnostic Mode

H
CAN Diag Support Mntr

Self Diagnostic Result
ECU Identification
System Sub System I
Configuration
Work support
Data Monitor
Active Test
J
Door lock DOOR LOCK × × ×

Rear window defogger REAR DEFOGGER × × K
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
INL
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × × M
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITIONER ×
N
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × × × O
Interior room lamp battery saver BATTERY SAVER × × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × × × P
Signal buffer system SIGNAL BUFFER × ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×
INT LAMP

INT LAMP : CONSULT Function (BCM - INT LAMP) INFOID:0000000010228002
DATA MONITOR
Monitor Item [Unit] Description

IGN ON SW [On/Off] Indicates condition of ignition switch ON position.
KEY ON SW [On/Off] Indicates condition of key switch.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
KEY CYL LK-SW [On/Off] Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN-SW [On/Off] Indicates condition of unlock signal from door key cylinder switch.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch.
KEYLESS LOCK [On/Off] Indicates condition of lock signal from keyfob.
KEYLESS UNLOCK [On/Off] Indicates condition of unlock signal from keyfob.
ACTIVE TEST
Test Item Description

IGN ILLUM This test is able to check ignition keyhole illumination operation [Off/On].
INT LAMP This test is able to check interior room lamp operation [Off/On].
WORK SUPPORT
Support Item Setting Description

Off Interior room lamp timer function OFF.
SET I/L D-UNLCK INTCON
On* Interior room lamp timer function ON.
MODE7 0 sec.
MODE6 5 sec.
MODE5 4 sec.
ROOM LAMP ON TIME SET MODE4 3 sec. Sets the interior room lamp gradual brightening time.
MODE3 2 sec.
MODE2* 1 sec.
MODE1 0.5 sec.
MODE7 0 sec.
MODE6 5 sec.
MODE5 4 sec.
ROOM LAMP OFF TIME SET MODE4 3 sec. Sets the interior room lamp gradual dimming time.
MODE3 2 sec.
MODE2* 1 sec.
MODE1 0.5 sec.
* : Initial setting
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER) INFOID:0000000010228003
DATA MONITOR

Monitor Item [Unit] Description A

B

DOOR SW-RR [On/Off] Indicates condition of rear door switch RH. C
KEY CYL LK SW [On/Off] Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN SW [On/Off] Indicates condition of unlock signal from door key cylinder switch. D
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch.
E
ACTIVE TEST F
Test item Description

G
BATTERY SAVER This test is able to check battery saver operation [Off/On].
WORK SUPPORT
H
MODE2 60 min
ROOM LAMP TIMER SET Sets the interior room lamp battery saver timer operating time.
MODE1* 10 min I
*: Initial setting
INL

POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [WITH POWER DOOR LOCKS]
DTC/CIRCUIT DIAGNOSIS
BCM
BCM : Diagnosis Procedure INFOID:0000000010228010
Regarding Wiring Diagram information, refer to BCS-43, "Wiring Diagram".
1. CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not blown.
Terminal No. Signal name Fuses and fusible link No.

57 21 (10A)
Battery power supply
70 G (50A)
11 Ignition ACC or ON 4 (10A)
38 Ignition ON or START 1 (10A)
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Terminals Power Voltage (V) (Ap-

Connector Condition
(+) (-) source prox.)
Ignition
ACC
switch
11 Ground power Battery voltage
ACC or
supply
M18 ON
LIIA2415E
Ignition Ignition
38 Ground power switch ON Battery voltage
supply or START
Battery Ignition
57 Ground power switch Battery voltage
supply OFF
M20
Battery Ignition
70 Ground power switch Battery voltage
supply OFF
Is the measurement value normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.
A
BCM
Continuity
Connector Terminal Ground
B
M20 67 Yes
Does continuity exist?
YES >> Inspection End. C
NO >> Repair or replace harness.
LIIA0915E
INL

BATTERY SAVER OUTPUT/POWER SUPPLY CIRCUIT
Description INFOID:0000000009480136
Provides the battery saver output/power supply. Also cuts the power supply when the interior room lamp bat-
tery saver is activating.
Component Function Check INFOID:0000000009480137
1.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY FUNCTION

WITH CONSULT
1. Turn ignition switch ON.
2. Turn each interior room lamp ON.
- Front room/map lamp assembly
- Vanity lamps (if equipped)
- Room lamp 2nd row
3. Select “BATTERY SAVER” of BCM (BATTERY SAVER) active test item.
4. While operating the test item, check that each interior room lamp turns ON/OFF.
OFF : Interior room lamp OFF

ON : Interior room lamp ON
Is the inspection result normal?
YES >> Battery saver output/power supply circuit is normal.
NO >> Refer to INL-16, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000009480138
Regarding Wiring Diagram information, refer to INL-37, "Wiring Diagram - With Power Door Lock System".
1.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY OUTPUT

WITH CONSULT
2. Select “BATTERY SAVER” of BCM (BATTERY SAVER) active
test item.
3. While operating the test item, check voltage between BCM con-
nector M20 terminal 56 and ground.
(+) Test item

(-) Voltage
Connector Terminal BATTERY SAVER
OFF 0V
M20 56 Ground
ON Battery voltage ALLIA0408GB

YES >> GO TO 2
NO >> Replace BCM after making sure the battery saver output/power supply circuit is not shorted to
voltage. Refer to BCS-49, "Removal and Installation".
2.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY OPEN CIRCUIT
2. Disconnect the following connectors.
- BCM M20
- Ignition keyhole illumination (if equipped)
- Front room/map lamp assembly
- Vanity lamp LH (if equipped)
- Vanity lamp RH (if equipped)

- Room lamp 2nd row
3. Check continuity between BCM connector M20 terminal 56 and each interior room lamp connector. A
BCM Each interior room lamp

Continuity
Connector Terminal Connector Terminal B
Ignition keyhole illumination (if equipped) M150 1
Front room/map lamp assembly R9 1
C
M20 56 Vanity lamp LH (if equipped) B80 1 Yes
Vanity lamp RH (if equipped) B81 1
Room lamp 2nd row R10 2 D
YES >> GO TO 3
NO >> Repair the harness or connectors. E
3.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY SHORT CIRCUIT

Check continuity between BCM connector M20 terminal 56 and F
ground.
Connector Terminal — Continuity G

M20 56 Ground No
H
YES >> Replace the interior room lamp. Refer to INL-63,
"Removal and Installation".
NO >> Repair the harness or connectors.
ALLIA0409GB I
INL

Controls the following interior room lamps (ground side) by PWM signal.
• Front room/map lamp assembly
• Room lamp 2nd row
NOTE:
PWM signal control period is approximately 250 Hz (in the gradual brightening/dimming).
CAUTION:
Before performing the diagnosis, check that the following is normal.
• Battery saver output/power supply
• Front room/map lamp bulbs (if equipped)
• Room lamp 2nd row bulb
1.CHECK INTERIOR ROOM LAMP CONTROL FUNCTION
WITH CONSULT
1. Switch the front room/map lamp assembly and room lamp 2nd row switches to DOOR.
3. Select “INT LAMP” of BCM (INT LAMP) active test item.
4. While operating the test item, check that each interior room lamp turns ON/OFF (gradual brightening/dim-
ming).
ON : Interior room lamp gradual brightening

OFF : Interior room lamp gradual dimming
YES >> Interior room lamp control circuit is normal.
1.CHECK INTERIOR ROOM LAMP CONTROL OUTPUT

WITH CONSULT
2. Select “INT LAMP” of BCM (INT LAMP) active test item.
(+)
(-) INT LAMP Voltage
Connector Terminal
ON 0V
M20 63 Ground
OFF Battery voltage
YES >> Interior room lamp control circuit is operating normally. ALLIA0410GB
Fixed ON>>GO TO 3
Fixed OFF>> GO TO 2
2.CHECK INTERIOR ROOM LAMP CONTROL OPEN CIRCUIT

2. Disconnect BCM connector M20, room lamp 2nd row connector A
and front room/map lamp connector.
3. Check continuity between BCM connector M20 (A) terminal 63
and interior room lamp connectors.
B
Terminal Terminal
Continuity
Connector Terminal Component Connector Terminal C
Room lamp 2nd
R10 (B) 1
row
M20 (A) 63 Yes
Front room/map
R9 (C) 2
D
lamp
YES >> Check interior room lamp for an open. If OK, replace the E
BCM. Refer to BCS-49, "Removal and Installation". If
NG, replace the interior room lamp. Refer to INL-63,
"Removal and Installation". F
G
AWLIA0727ZZ
3.CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT

1. Turn ignition switch OFF. H
2. Disconnect BCM connector M20, room lamp 2nd row connector
and front room/map lamp connector.
3. Check continuity between BCM connector M20 terminal 63 and I
ground.
Connector Terminal — Continuity J

M20 63 Ground No
YES >> Check interior room lamp for a short circuit. If OK, ALLIA0413GB
K
replace the BCM. Refer to BCS-49, "Removal and
Installation". If NG, replace the interior room lamp. Refer to INL-63, "Removal and Installation".
NO >> Repair the harness or connectors. INL

CARGO LAMP CONTROL CIRCUIT
Controls the cargo lamp relay coil (ground side) to turn the cargo lamp ON and OFF.
CAUTION:
• Fuse
• Cargo lamp bulb
1.CHECK CARGO LAMP OPERATION

Check the cargo lamp operation from the cargo lamp switch, the door switches, and a keyfob (if equipped).
Is the cargo lamp operative from all of the above switches and the keyfob (if equipped)?
YES >> At this time, the cargo lamp operates normally.
NO >> • Inoperative from all the above switches and the keyfob, GO TO 6
• Inoperative from cargo lamp switch only, GO TO 2
• Inoperative from door switches only, refer to DLK-27, "KING CAB : Description" (king cab), DLK-
29, "CREW CAB : Description" (crew cab).
• Inoperative from keyfob only, refer to DLK-51, "Description".
• Fixed ON, GO TO 2
2.CHECK CARGO LAMP SWITCH
Check the cargo lamp switch. Refer to INL-22, "Component Inspection".
YES >> • For inoperative from cargo lamp switch only, GO TO 3
• For fixed ON, GO TO 5
NO >> Replace the cargo lamp switch.
3.CHECK CARGO LAMP SWITCH CIRCUIT OPEN
1. Disconnect BCM connector M18 and cargo lamp switch connector.
2. Check continuity between BCM connector M18 terminal 31 and cargo lamp switch connector M71 termi-
nal 1.
BCM Cargo lamp switch

Continuity
Connector Terminal Connector Terminal
M18 31 M71 1 Yes
YES >> GO TO 4
NO >> Repair harness or connectors.
4.CHECK CARGO LAMP SWITCH GROUND CIRCUIT
1. Check continuity between cargo lamp switch connector M71 terminal 3 and ground.
Connector Terminal — Continuity

M71 3 Ground Yes
YES >> Replace BCM. Refer to BCS-49, "Removal and Installation".

5.CHECK CARGO LAMP SWITCH CIRCUIT SHORT A

2. Check continuity between BCM connector M18 terminal 31 and ground.
B
M18 31 Ground No
Is the inspection result normal? C
YES >> GO TO 6
6.CHECK CARGO LAMP RELAY D
Check the cargo lamp relay. Refer to INL-22, "Component Inspection".

Is the inspection result normal? E
YES >> • For fixed OFF, GO TO 7
NO >> Replace the cargo lamp relay. F
7.CHECK CARGO LAMP RELAY CONTROL
While operating the cargo lamp switch, check voltage between BCM
connector M19 terminal 50 and ground. G
Cargo lamp
Connector Terminal — Voltage H
switch
ON 0V
M19 50 Ground
OFF Battery voltage
I
YES >> GO TO 8
NO >> GO TO 11 ALLIA0556GB
J
8.CHECK CARGO LAMP VOLTAGE
1. Disconnect the cargo lamp connector.
2. While operating the cargo lamp switch, check voltage between cargo lamp connector B161 terminal 3 and K
ground.
Cargo lamp INL

Connector Terminal — Voltage
switch
B161 3 Ground ON Battery voltage
Is the inspection result normal? M
YES >> GO TO 9
NO >> GO TO 10
N
9.CHECK CARGO LAMP GROUND CIRCUIT
1. While operating the cargo lamp switch, check voltage between cargo lamp connector B161 terminal 3 and
terminal 2. O
Terminal Terminal Cargo lamp

Connector Voltage
(+) (-) switch
P
B161 3 2 ON Battery voltage
YES >> Replace cargo lamp.
10.CHECK CARGO LAMP RELAY VOLTAGE PART 1

Check voltage between cargo lamp relay connector M165 terminal 5
and ground.
Cargo lamp relay

Voltage
M165 5 Battery voltage
YES >> Repair harness or connectors between cargo lamp relay
and cargo lamp.
NO >> Repair harness or connector between splice and cargo AWLIA0810ZZ
lamp relay.
and ground.
Cargo lamp relay

Voltage
YES >> GO TO 12
AWLIA0812ZZ
12.CHECK CARGO LAMP RELAY CONTROL CIRCUIT OPEN

1. Disconnect BCM connector M19 and cargo lamp relay.
2. Check continuity between BCM connector M19 terminal 50 and cargo lamp relay connector M165 termi-
nal 1.
BCM Cargo lamp relay

Continuity
M19 50 M165 1 Yes
13.CHECK CARGO LAMP RELAY CONTROL CIRCUIT SHORT

M19 50 Ground No
YES >> Replace BCM after making sure the cargo lamp power supply circuit is not shorted to voltage.
Refer to BCS-49, "Removal and Installation".
Component Inspection INFOID:0000000009480144
CARGO LAMP SWITCH


2. Disconnect cargo lamp switch connector. A
3. Check continuity between cargo lamp switch terminals 1and 3.
Cargo lamp switch B

Condition Continuity
Terminal
ON Yes
1−3 C
OFF No
AWLIA0804ZZ
YES >> Inspection End D
NO >> Replace cargo lamp switch.
CARGO LAMP RELAY
1.CHECK CARGO LAMP RELAY E

2. Disconnect cargo lamp relay.
F
3. Supply power to terminal 2 and ground to terminal 1 of the cargo
lamp relay.
4. Check continuity between cargo lamp relay terminals 3 and 5.
G
Terminal Condition Continuity
Power and ground supplied to terminals 1 and 2 Yes
3 5 H
No power and ground supplied No
Is the inspection result normal? SEF497Y
YES >> Inspection End I

NO >> Replace cargo lamp relay.
INL

IGNITION KEYHOLE ILLUMINATION CONTROL CIRCUIT
Controls the ignition keyhole illumination (ground side) to turn the ignition keyhole illumination ON and OFF.
CAUTION:
• Battery saver output/power supply circuit
• Ignition keyhole illumination bulb
1.CHECK IGNITION KEYHOLE ILLUMINATION OPERATION
WITH CONSULT
1. Turn the ignition switch ON.
2. Select “IGN ILLUM” of BCM (INT LAMP) active test item.
3. While operating the test item, check that the ignition keyhole illumination turns ON/OFF
ON : Ignition keyhole illumination ON

OFF : Ignition keyhole illumination OFF
YES >> Ignition keyhole illumination circuit is normal.
1.CHECK IGNITION KEYHOLE OUTPUT

WITH CONSULT
2. Select “IGN ILLUM” of BCM (INT LAMP) active test item.
Connector Terminal — IGN ILLUM Voltage

ON 0V
M18 1 Ground
OFF Battery voltage
YES >> Ignition keyhole illumination control circuit is operating ALLIA0420GB
normally.
Fixed ON>>GO TO 3.
Fixed OFF>> GO TO 2.
2.CHECK IGNITION KEYHOLE ILLUMINATION OPEN CIRCUIT

2. Disconnect BCM connector M18 and ignition keyhole illumina- A
tion connector.
3. Check continuity between BCM connector M18 (A) terminal 1
and ignition keyhole illumination connector M150 (B) terminal 2.
B
BCM Ignition keyhole illumination

Continuity
Connector Terminal Connector Terminal C
M18 (A) 1 M150 (B) 2 Yes
Is the inspection result normal? WKIA5803E
YES >> Check the ignition keyhole illumination for an open. If OK, replace the BCM. Refer to BCS-49, D
"Removal and Installation". If NG, replace ignition keyhole illumination.
3.CHECK IGNITION KEYHOLE ILLUMINATION SHORT CIRCUIT E

2. Disconnect BCM connector M18 and ignition keyhole illumina-
F
tion connector.
3. Check continuity between BCM connector M18 terminal 1 and
ground.
G
M18 1 Ground No
H
YES >> Check the ignition keyhole illumination for a short circuit. ALLIA0422GB
If OK, replace the BCM. Refer to BCS-49, "Removal and I

Installation". If NG, replace ignition keyhole illumination.
J
INL

BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [WITH POWER DOOR LOCKS]
ECU DIAGNOSIS INFORMATION

Reference Value INFOID:0000000010228011
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob relative signal strength
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status

Ignition switch OFF or ON Off
ACC ON SW
Ignition switch ACC On
A/C switch OFF Off
AIR COND SW
A/C switch ON On
AIR PRESS FL Front left tire air pressure value kPa, kg/cm2, psi
AIR PRESS FR Front right tire air pressure value kPa, kg/cm2, psi
AIR PRESS RL Rear left tire air pressure value kPa, kg/cm2, psi
AIR PRESS RR Rear right tire air pressure value kPa, kg/cm2, psi
Lighting switch OFF Off
AUTO LIGHT SW
Lighting switch AUTO On
Brake pedal released Off
BRAKE SW
Brake pedal applied On
Seat belt buckle unfastened Off
BUCKLE SW
Seat belt buckle fastened On
Buzzer in combination meter OFF Off
BUZZER
Buzzer in combination meter ON On
Cargo lamp switch OFF Off
CARGO LAMP SW
Cargo lamp switch ON On
Door lock/unlock switch does not operate Off
CDL LOCK SW
Press door lock/unlock switch to the LOCK side On
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side On
Front door RH closed Off
DOOR SW-AS
Front door RH opened On
Front door LH closed Off
DOOR SW-DR
Front door LH opened On
Rear door LH closed Off
DOOR SW-RL
Rear door LH opened On
Rear door RH closed Off
DOOR SW-RR
Rear door RH opened On

A
Blower motor fan switch OFF Off
FAN ON SIG
Blower motor fan switch ON On
Front fog lamp switch OFF Off B
FR FOG SW
Front fog lamp switch ON On
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On C
Front wiper switch OFF Off
FR WIPER LOW
Front wiper switch LO On
D
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off E
FR WIPER INT
Front wiper switch INT On
Any position other than front wiper stop position Off
FR WIPER STOP F
Front wiper stop position On
When hazard switch is not pressed Off
HAZARD SW
When hazard switch is pressed On G
Headlamp switch OFF Off
HEAD LAMP SW 1
Headlamp switch 1st On
H
HEAD LAMP SW 2
High beam switch OFF Off I
HI BEAM SW
High beam switch HI On
ID registration of front left tire incomplete YET
ID REGST FL1 J
ID registration of front left tire complete DONE
ID registration of front right tire incomplete YET
ID REGST FR1
ID registration of front right tire complete DONE
K
ID registration of rear left tire incomplete YET
ID REGST RL1
ID registration of rear left tire complete DONE
ID registration of rear right tire incomplete YET INL
ID REGST RR1
ID registration of rear right tire complete DONE
Ignition switch OFF or ACC Off
IGN ON SW M
Ignition switch ON On
IGN SW CAN
Ignition switch ON On N
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
Door key cylinder LOCK position Off
KEY CYL LK-SW O
Door key cylinder other than LOCK position On
Door key cylinder UNLOCK position Off
KEY CYL UN-SW
Door key cylinder other than UNLOCK position On P
Mechanical key is removed from key cylinder Off
KEY ON SW
Mechanical key is inserted to key cylinder On
LOCK button of key fob is not pressed Off
KEYLESS LOCK
LOCK button of key fob is pressed On

PANIC button of key fob is not pressed Off
KEYLESS PANIC
PANIC button of key fob is pressed On
UNLOCK button of key fob is not pressed Off
KEYLESS UNLOCK
UNLOCK button of key fob is pressed On
LIGHT SW 1ST
Lighting switch 1st On
• Ignition switch OFF or ACC
Off
OIL PRESS SW • Engine running
Bright outside of the vehicle Close to 5V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0V
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On
Turn signal switch OFF Off
TURN SIGNAL L
Turn signal switch LH On
TURN SIGNAL R
Turn signal switch RH On
VEHICLE SPEED While driving Equivalent to speedometer reading
Low tire pressure warning lamp in combination meter OFF Off
WARNING LAMP
Low tire pressure warning lamp in combination meter ON On

Terminal Layout INFOID:0000000010228012
INL
P
LIIA2443E
Physical Values INFOID:0000000010228013

Signal Measuring condition

Wire Reference value or waveform
Terminal Item input/ Ignition
color Operation or condition (Approx.)
output switch
Ignition keyhole illumi- Door is locked (SW OFF) Battery voltage

1 BR Output OFF
nation Door is unlocked (SW ON) 0V
Combination switch Lighting, turn, wiper OFF

2 P Input ON
input 5 Wiper dial position 4
SKIA5291E

3 SB Input ON
SKIA5292E

4 V Input ON
SKIA5291E
Combination switch
5 L
input 2
Lighting, turn, wiper OFF

Input ON
Combination switch Wiper dial position 4
6 R
input 1
SKIA5292E
Front door lock as- ON (open, 2nd turn) Momentary 1.5V

7 GR sembly LH (key cylin- Input
der switch) unlock OFF (closed) 0V
OFF
Front door lock as- On (open) Momentary 1.5V
8 SB sembly LH (key cylin- Input
der switch) lock OFF (closed) 0V
OFF (brake pedal is not de-

0V
pressed)
9 LG Brake sw Input OFF
ON (brake pedal is de-
Battery voltage
pressed)
Ignition switch (ACC ACC or
11 G/B Input Ignition switch ACC or ON Battery voltage
or ON) ON
Front door switch RH
ON (open) 0V
(All)
Rear door switch up-
12 LG Input OFF
per RH (King Cab)
OFF (closed) Battery voltage
Rear door switch low-
er RH (King Cab)


Wire Reference value or waveform A
output switch
Rear door switch RH ON (open) 0V

13 L
(Crew Cab)
Input OFF B
Tire pressure warning
15 W Input OFF — 5V
check connector
C
Remote keyless entry
18 BR receiver and optical Output OFF — 0V
sensor (Ground)
D

E
19 V receiver (power sup- Output OFF Ignition switch OFF
ply)
F
LIIA1893E
G
Stand-by (keyfob buttons re-
leased)
H
Remote keyless entry LIIA1894E
20 G receiver signal (Sig- Input OFF
nal) I
When remote keyless entry

receiver receives signal from
keyfob (keyfob buttons J
pressed)
LIIA1895E
K
Just after turning ignition switch
OFF →
21 GR NATS antenna amp. Input Ignition switch (OFF → ON) ON: Pointer of tester should
ON
move.
INL
Security indicator Goes OFF → illuminates (Ev-
23 G Output OFF Battery voltage → 0V
lamp ery 2.4 seconds)
OFF → M
25 BR NATS antenna amp. Input Ignition switch (OFF → ON) ON: Pointer of tester should
ON
move.
Compressor ON sig- A/C switch OFF 5V

27 W Input ON N
nal A/C switch ON 0V
Front blower motor OFF Battery voltage
28 R Front blower monitor Input ON
Front blower motor ON 0V O
ON 0V
29 G Hazard switch Input OFF
OFF 5V
P
ON 0V
31 GR Cargo lamp switch Input OFF
OFF Battery voltage


output switch

32 BG Output ON
output 5 Wiper dial position 4
SKIA5291E

33 GR Output ON
SKIA5292E

34 G Output ON
SKIA5291E
Combination switch
35 BR
output 2

Output ON
36 LG
output 1
SKIA5292E
Key inserted Battery voltage

37 B Key switch Input OFF
Key removed 0V
38 W/R Ignition switch (ON) Input ON — Battery voltage
39 L CAN-H — — — —
40 P CAN-L — — — —
Rear window defogger switch
0V
Rear window defogger ON
41 Y Input ON
switch Rear window defogger switch
5V
OFF
ON (lock) 0V
45 V Lock switch Input OFF
OFF Battery voltage
ON (unlock) 0V
46 LG Unlock switch Input OFF
OFF Battery voltage
Front door switch LH
ON (open) 0V
(All)
47 GR Input OFF
per LH (King Cab)
er LH (King Cab)


output switch
Rear door switch LH ON (open) 0V

48 P
(Crew Cab)
Input OFF B
Any door open (ON) 0V
50 P Cargo lamp Output OFF
All doors closed (OFF) Battery voltage C
D
Trailer turn signal
51 BG Output ON Turn right ON
(right)
E
SKIA3009J
52 LG Trailer turn signal (left) Output ON Turn left ON

G
SKIA3009J
H
10 minutes after ignition
OFF 0V
56 R/Y Battery saver output Output switch is turned OFF
ON — Battery voltage
I
57 R/Y Battery power supply Input — — Battery voltage
When optical sensor is illumi-
3.1V or more
nated
58 W Optical sensor Input ON J
When optical sensor is not illu-
0.6V or less
minated
Front door lock as- OFF (neutral) 0V

59 GR Output OFF K
sembly LH (unlock) ON (unlock) Battery voltage
INL
60 LG Turn signal (left) Output ON Turn left ON

M
SKIA3009J
61 G Turn signal (right) Output ON Turn right ON O
SKIA3009J P
Interior room/map Any door ON (open) 0V
63 BR Output OFF
lamp switch OFF (closed) Battery voltage
All door lock actuators OFF (neutral) 0V

65 V Output OFF
(lock) ON (lock) Battery voltage


output switch
Front door lock actua- OFF (neutral) 0V
tor RH, rear door lock
66 L Output OFF
actuators LH/RH (un- ON (unlock) Battery voltage
lock)
67 B Ground Input ON — 0V
Ignition switch ON Battery voltage
Within 45 seconds after igni-
Battery voltage
tion switch OFF
Power window power More than 45 seconds after ig-
681 O
supply (RAP)
Output — 0V
nition switch OFF
When front door LH or RH is
open or power window timer 0V
operates
Battery voltage
tion switch OFF
682 SB
supply (RAP)
Output — 0V
nition switch OFF
operates
69 P Power window power
Output OFF — Battery voltage
supply (BAT)
70 W Battery power supply Input OFF — Battery voltage
1: King cab
2: Crew cab
Fail Safe INFOID:0000000010228014
Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.
Display contents of CONSULT Fail-safe Cancellation

When the BCM re-establishes communication with the other mod-
U1000: CAN COMM CIRCUIT Inhibit engine cranking
ules.
DTC Inspection Priority Chart INFOID:0000000010228015
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 • U1000: CAN COMM CIRCUIT
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
2
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM

Priority DTC
A
• C1729: VHCL SPEED SIG ERR
3
• C1735: IGNITION SIGNAL
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR B
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
C
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL D
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
4
• C1716: [PRESSDATA ERR] FL E
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL F
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL G
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
H
DTC Index INFOID:0000000010228016
NOTE: I
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again. J
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again. K
Low tire pressure

CONSULT display Fail-safe Reference page
warning lamp ON INL
No DTC is detected.
further testing — — —
may be required.
M
U1000: CAN COMM CIRCUIT — — BCS-26
B2190: NATS ANTTENA AMP — — SEC-18
B2191: DIFFERENCE OF KEY — — SEC-21 N
B2192: ID DISCORD BCM-ECM — — SEC-22
B2193: CHAIN OF BCM-ECM — — SEC-24
O
C1708: [NO DATA] FL — X WT-15
C1709: [NO DATA] FR — X WT-15
C1710: [NO DATA] RR — X WT-15 P
C1711: [NO DATA] RL — X WT-15
C1712: [CHECKSUM ERR] FL — X WT-17
C1713: [CHECKSUM ERR] FR — X WT-17
C1714: [CHECKSUM ERR] RR — X WT-17
C1715: [CHECKSUM ERR] RL — X WT-17

Low tire pressure
warning lamp ON
C1716: [PRESSDATA ERR] FL — X WT-19
C1717: [PRESSDATA ERR] FR — X WT-19
C1718: [PRESSDATA ERR] RR — X WT-19
C1719: [PRESSDATA ERR] RL — X WT-19
C1720: [CODE ERR] FL — X WT-17
C1721: [CODE ERR] FR — X WT-17
C1722: [CODE ERR] RR — X WT-17
C1723: [CODE ERR] RL — X WT-17
C1724: [BATT VOLT LOW] FL — X WT-17
C1725: [BATT VOLT LOW] FR — X WT-17
C1726: [BATT VOLT LOW] RR — X WT-17
C1727: [BATT VOLT LOW] RL — X WT-17
C1729: VHCL SPEED SIG ERR — X WT-21
C1735: IGNITION SIGNAL — X WT-22

INTERIOR ROOM LAMP
< WIRING DIAGRAM > [WITH POWER DOOR LOCKS]
WIRING DIAGRAM A
INTERIOR ROOM LAMP
Wiring Diagram - With Power Door Lock System INFOID:0000000009480154
B
INL
ABLWA2387GB

INTERIOR ROOM LAMP
ABLWA2031GB

INTERIOR ROOM LAMP
INL
ABLWA2388GB

INTERIOR ROOM LAMP
ABLIA0683GB

INTERIOR ROOM LAMP
INL
ABLIA5634GB

INTERIOR ROOM LAMP
ABLIA5635GB

INTERIOR ROOM LAMP
INL
ABLIA5636GB

INTERIOR ROOM LAMP
ABLIA5637GB

INTERIOR ROOM LAMP
INL
ABLIA5638GB

INTERIOR ROOM LAMP
ABLIA5639GB

INTERIOR ROOM LAMP
INL
ABLIA5640GB

INTERIOR ROOM LAMP
ABLIA5641GB

INTERIOR ROOM LAMP
INL
ABLIA5642GB

ILLUMINATION
ILLUMINATION
Wiring Diagram INFOID:0000000009480155
ABLWA2390GB

ILLUMINATION
INL
ABLWA2399GB

ILLUMINATION
ABLWA2030GB

ILLUMINATION
INL
ABLIA5647GB

ILLUMINATION
ABLIA5648GB

ILLUMINATION
INL
ABLIA5691GB

ILLUMINATION
ABLIA5669GB

ILLUMINATION
INL
ABLIA5649GB

ILLUMINATION
ABLIA5692GB

ILLUMINATION
INL
ABLIA5650GB

INTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [WITH POWER DOOR LOCKS]
SYMPTOM DIAGNOSIS
Symptom Table INFOID:0000000009480156
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom Possible cause Inspection item

All of the following lamps do not turn ON
• Harness between BCM and each
• Front room/map lamp assembly
interior room lamp
• Room lamp 2nd row Battery saver output/power supply
• Vanity mirror lamps (if equipped) circuit
door switch
• Ignition keyhole illumination (if equipped) Refer to INL-16.
• BCM
Some or all of the following interior room lamps

do not turn ON/OFF Interior room lamp control circuit
interior room lamp
• Front room/map lamp assembly Refer to INL-18.
• BCM
• Room lamp 2nd row
• Harness between fuse block (J/B)
and cargo lamp relay
• Harness between cargo lamp relay
Cargo lamp control circuit
Cargo lamp does not turn ON/OFF and cargo lamp
Refer to INL-20.
• Harness between BCM and cargo
lamp relay
• BCM
Ignition keyhole illumination does not turn ON/ • Harness between BCM and igni-
Ignition keyhole illumination circuit
OFF tion keyhole illumination
Refer to INL-24
• BCM
Check the interior room lamp setting.
Interior room lamp timer does not activate.
— Refer to INL-12, "INT LAMP : CON-
(It turns ON/ OFF when the door opens/closes.)
SULT Function (BCM - INT LAMP)".
Check the interior room lamp battery
saver setting.
Interior room lamp battery saver does not acti-
— Refer to BCS-22, "BATTERY SAVER
vate.
: CONSULT Function (BCM - BAT-
TERY SAVER)".

PRECAUTIONS
< PRECAUTION > [WITH POWER DOOR LOCKS]
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000010118811
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS H
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a I
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the J
battery and wait at least three minutes before performing any service.
Precaution for Work INFOID:0000000009480158
K
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it. INL
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one. M
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
N
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt: O
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off. P
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.

PREPARATION
< PREPARATION > [WITH POWER DOOR LOCKS]
PREPARATION
PREPARATION
Special Service Tool INFOID:0000000009480159
The actual shape of the tools may differ from those illustrated here.
Tool number Description
(TechMate No.)
Tool name
— Removing trim components
(J-46534)
Trim Tool Set
AWJIA0483ZZ

INTERIOR ROOM LAMP
< REMOVAL AND INSTALLATION > [WITH POWER DOOR LOCKS]
REMOVAL AND INSTALLATION A

INTERIOR ROOM LAMP
Removal and Installation INFOID:0000000009480160
B
FRONT ROOM/MAP LAMP ASSEMBLY

Removal C
The front room/map lamp assembly is replaced as part of the roof
console. Refer to INT-25, "Removal and Installation".
: Front D
: Metal clip
F
AWLIA0867ZZ
Installation
Installation is in the reverse order of removal. G
Bulb or Lens Replacement

1. Using a suitable tool (A), remove the front room/map lamp RH H
and/or LH lenses (1) as necessary.
: Front
: Pawl I
2. Release one side of the bulb (2) from the tab using a suitable
tool, then pull straight downward to remove.
J
Front room/ : 12V - 8W
map lamp as-
sembly bulb
K
INL
N
AWLIA1667ZZ
3. Install the new bulb into the socket tabs. O

4. Install the front room/map lamp lens(es).
VANITY LAMP
P
Removal

INTERIOR ROOM LAMP
The vanity lamp is replaced as part of the sun visor assembly. Refer
to INT-25, "Removal and Installation".
ALLIA0583ZZ
Installation
Installation is in the reverse order of removal.
Bulb Replacement
The vanity mirror lamp bulb is replaced as part of the sun visor assembly. Refer to INT-25, "Removal and
Installation".
ROOM LAMP 2ND ROW
Removal
1. Using a suitable tool (A), release the pawls and remove the
room lamp lens (1).
: Pawl
2. Remove room lamp screws (2).
3. Disconnect the harness connector from the room lamp and
remove.
AWLIA1680ZZ
Installation
1. Using a suitable tool, release the pawls and remove the room lamp lens.
2. Release the room lamp bulb retainers (1), then pull bulb (2)
straight out to remove.
3. Install the bulb (2) securely into the room lamp bulb retainers (1).
Room lamp bulb : 12V - 8W
ALLIA0326ZZ

INTERIOR ROOM LAMP
4. Install the room lamp lens. A
INL

ILLUMINATION
ILLUMINATION
ILLUMINATION CONTROL SWITCH

Removal
The illumination control switch is replaced as a part of the combina-
tion meter. Refer to MWI-90, "Removal and Installation".
LKIA0579E
Installation
SHIFT SELECTOR FINISHER LAMP
Removal
1. Remove shift selector finisher from center console. Refer to IP-25, "Removal and Installation".
2. Rotate shift selector finisher lamp socket (2) with bulb (3) coun-
terclockwise, then pull away from finisher (1).
ALLIA0590ZZ
Installation
Bulb Replacement
2. Remove shift selector finisher lamp socket (1), then pull bulb (2)
straight out away from socket.
3. Install the bulb (2) into the shift selector finisher socket (1).
AT finisher lamp bulb : 12V - 3W
ALLIA0321ZZ
4. Install shift selector finisher in center console. Refer to IP-25, "Removal and Installation".

BULB SPECIFICATIONS
< SERVICE DATA AND SPECIFICATIONS (SDS) [WITH POWER DOOR LOCKS]
SERVICE DATA AND SPECIFICATIONS (SDS) A

BULB SPECIFICATIONS
Bulb Specifications INFOID:0000000009480162
B
Item Wattage (W)*

C
Front room/map lamp 8
Vanity lamp –
Room lamp 2nd row 8 D
Shift selector finisher lamp 3
*: Always check with the Parts Department for the latest parts information.
E
INL

< BASIC INSPECTION > [WITHOUT POWER DOOR LOCKS]
BASIC INSPECTION
Work Flow INFOID:0000000009480163
OVERALL SEQUENCE
AWLIA1837GB

DETAILED FLOW A
1.INTERVIEW FOR MALFUNCTION
Find out what the customer's concerns are.
B
>> GO TO 2
2.SYMPTOM CHECK C
Verify the symptom from the customer's information.
D
>> GO TO 3
3.BASIC INSPECTION
Check the operation of each part. Check that any concerns occur other than those mentioned in the customer E
interview.
>> GO TO 4 F
4.SELF-DIAGNOSIS WITH CONSULT
Perform the self-diagnosis with CONSULT. Check that any DTC is detected.
G
YES >> GO TO 5
NO >> GO TO 6 H
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
I
>> GO TO 9
6.FAIL-SAFE ACTIVATION CHECK J
Determine if the customer’s concern is related to fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7 K
NO >> GO TO 8
7.SYSTEM DIAGNOSIS INL
Perform the system diagnosis for the system in which the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9 M
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
N
>> GO TO 9
9.MALFUNCTION PART REPAIR O
Repair or replace the malfunctioning part.
P
>> GO TO 10
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform the self-diagnosis with CONSULT. Verify that no DTCs are detected. Erase all DTCs detected prior to
the repair. Verify that DTC is not detected again.
YES >> GO TO 5

NO >> GO TO 11
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
NO >> GO TO 3

INTERIOR ROOM LAMP
< SYSTEM DESCRIPTION > [WITHOUT POWER DOOR LOCKS]
SYSTEM DESCRIPTION A
INTERIOR ROOM LAMP
B
AWLIA2278GB
G
OUTLINE H
• Room lamp 2nd row and front room/map lamp (if equipped) are powered by fuse block (J/B) fuse number 21
(10A). When the lamp is set to the DOOR position, ground is provided through the door switches.
• Cargo lamp is controlled by the cargo lamp control function of the BCM. I
INL

INTERIOR ROOM LAMP
AWLIA2279ZZ
1. BCM M18, M19, M20 (view with lower 2. Key switch M27 3. Cargo lamp switch M71
instrument panel LH removed)
4. Front door switch LH B8 (crew cab) 5. Rear door switch LH B18 (crew cab) 6. Front door switch LH D213 (king cab)
Front door switch RH B108 (crew cab) Rear door switch RH B116 (crew cab) Front door switch RH D314 (king cab)
7. Cargo lamp B161 8. Room lamp 2nd row R10 9. Front room/map lamp assembly R9 (if
equipped)

BCM Provides ground for the cargo lamp relay.
Key switch Provides key in ignition status to the BCM.

INTERIOR ROOM LAMP
Provides door OPEN/CLOSED status to the BCM.
Door switches
Provides ground for the room lamp 2nd row. A
Cargo lamp switch Provides cargo lamp ON/OFF request to the BCM.
INL

AWLIA1754GB
The illumination lamps operation is dependent upon the position of the combination switch (lighting and turn
signal switch). When the combination switch (lighting and turn signal switch) is placed in the 1ST or 2ND posi-
tion (or if the auto light system is activated) the BCM (body control module) receives input requesting the park-
ing lamps to illuminate. This input is communicated to the IPDM E/R (intelligent power distribution module
engine room) via the CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls
the tail lamp relay coil. When energized, this relay directs power to the parking and illumination lamps, which
then illuminate.
BATTERY SAVER CONTROL
When the combination switch (lighting and turn signal switch) is in the 1ST or 2ND position and the ignition
switch is turned from ON or ACC to OFF, the battery saver control feature is activated. Under this condition,
the illumination lamps remain illuminated for 10 minutes unless the combination switch (lighting and turn signal
switch) position is changed. If the combination switch (lighting and turn signal switch) position is changed, then
the illumination lamps are turned off after a 30 second delay. When the combination switch (lighting and turn
signal switch) is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after illumination
lamps have been turned off by the battery saver control, the illumination lamps illuminate again.

WKIA5029E
I
1. IPDM E/R E122, E124 2. Combination switch (lighting and turn 3. Combination meter M24
signal switch) M28
4. Illumination control switch (built into 5. BCM M18, M20 (view with lower instru- J
combination meter) ment panel LH removed)

K

The BCM monitors the lighting switch position with the combina- INL
BCM tion switch reading function. The BCM requests, via CAN commu-
nication, that the IPDM E/R activate the tail lamp relay.
The IPDM E/R activates the tail lamp relay based on inputs re- M
IPDM E/R
ceived from the BCM via the CAN communication network.
The illumination control switch is a part of the combination meter.
The combination meter controls illumination intensity by varying
Combination meter (illumination control switch) N
ground to the illumination lamps based on the illumination control
switch position.
The combination switch (lighting and turn signal switch) provides
Combination switch (lighting and turn signal switch) O
input to the BCM about the lighting switch position.

COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010229282
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode Description

ECU Identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
CAN Diag Support Mntr

Self Diagnostic Result
ECU Identification
System Sub System
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITIONER ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × × ×
Signal buffer system SIGNAL BUFFER × ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×
INT LAMP

INT LAMP : CONSULT Function (BCM - INT LAMP) INFOID:0000000010229283
A
DATA MONITOR
Monitor Item [Unit] Description B

C
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH. D
KEY CYL LK-SW [On/Off] Indicates condition of lock signal from door key cylinder switch.
E
KEY CYL UN-SW [On/Off] Indicates condition of unlock signal from door key cylinder switch.
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch. F
G
ACTIVE TEST
Test Item Description

H
IGN ILLUM This test is able to check ignition keyhole illumination operation [Off/On].
INT LAMP This test is able to check interior room lamp operation [Off/On].
WORK SUPPORT I

J
Off Interior room lamp timer function OFF.
SET I/L D-UNLCK INTCON
On* Interior room lamp timer function ON.
MODE7 0 sec. K
MODE6 5 sec.
MODE5 4 sec.
ROOM LAMP ON TIME SET MODE4 3 sec. Sets the interior room lamp gradual brightening time.
INL
MODE3 2 sec.
MODE2* 1 sec.
M
MODE1 0.5 sec.
MODE7 0 sec.
MODE6 5 sec. N
MODE5 4 sec.
ROOM LAMP OFF TIME SET MODE4 3 sec. Sets the interior room lamp gradual dimming time.
O
MODE3 2 sec.
MODE2* 1 sec.
MODE1 0.5 sec. P
* : Initial setting

INTERIOR ROOM LAMP
< DTC/CIRCUIT DIAGNOSIS > [WITHOUT POWER DOOR LOCKS]
DTC/CIRCUIT DIAGNOSIS
INTERIOR ROOM LAMP
Regarding Wiring Diagram information, refer to INL-95, "Wiring Diagram - Without Power Door Lock System".
CAUTION:
• Fuse
• Interior room lamp bulbs
1.CHECK INTERIOR ROOM LAMP POWER SUPPLY

Check voltage between interior room lamp connectors and ground.
(+)
Component (-) Voltage
Connector Terminal
Room lamp 2nd row R10 2
Ground Battery voltage
Front room/map lamp R9 1
YES >> GO TO 2
2.CHECK INTERIOR ROOM LAMP GROUND
2. Disconnect BCM connectors M18, M19, room lamp 2nd row connector R10 and front room/map lamp
connector R9.
3. Check continuity between interior room lamp connectors and ground while opening/closing the door.
(+)
Component (-) Door states Continuity
Connector Terminal
Open Yes
Room lamp 2nd row R10 1
Closed No
Ground
Open Yes
Front room/map lamp R9 2
Closed No
YES >> Replace the interior room lamp. Refer to INL-63, "Removal and Installation".
NO >> GO TO 3
3.CHECK DOOR SWITCHES
Check the door switches. Refer to INL-79, "Component Inspection (Door Switch)".
YES >> • Crew cab models, repair the harness or connectors between the interior room lamp and the
door switches.
• King cab models, GO TO 4
NO >> Replace the door switch.
4.CHECK DOOR SWITCH GROUND (KING CAB)

INTERIOR ROOM LAMP
Check continuity between door switch connectors and ground.
A
(+)
Component (-) Continuity
Connector Terminal
B
Front door switch LH D213 3
Ground Yes
Front door switch RH D314 3
YES >> Repair the harness or connectors between the interior
room lamp and the door switches. AWLIA0866ZZ
NO >> Repair the harness or connectors between the door D
switch and ground.
Component Inspection (Door Switch) INFOID:0000000009480175
E
CREW CAB
1.CHECK DOOR SWITCHES F
1. Disconnect door switch.
2. Check continuity between door switch terminal 1 and ground.
G
Open Yes
Door switch 1 – Ground
Closed No H
NO >> Replace door switch. I
AWLIA0864ZZ
KING CAB
J
1.CHECK DOOR SWITCHES
1. Disconnect door switch.
2. Check continuity between door switch terminals 1 and 3. K
Item Terminal Condition Continuity

Open Yes INL
Door switches 1–3
Closed No
M
NO >> Replace door switch.
AWLIA0865ZZ

Controls the cargo lamp relay coil (ground side) to turn the cargo lamp ON and OFF.
Regarding Wiring Diagram information, refer to INL-95, "Wiring Diagram - Without Power Door Lock System".
CAUTION:
• Fuse
• Cargo lamp bulb
1.CHECK CARGO LAMP OPERATION

Check the cargo lamp operation from the cargo lamp switch, the door switches, and a keyfob (if equipped).
Is the cargo lamp operative from all of the above switches and the keyfob (if equipped)?
YES >> At this time, the cargo lamp operates normally.
NO >> • Inoperative from all the above switches and the keyfob, GO TO 6
• Inoperative from cargo lamp switch only, GO TO 2
• Inoperative from door switches only, refer to DLK-27, "KING CAB : Description" (king cab), DLK-
29, "CREW CAB : Description" (crew cab).
• Inoperative from keyfob only, refer to DLK-51, "Description".
• Fixed ON, GO TO 2
Check the cargo lamp switch. Refer to INL-82, "Component Inspection".
YES >> • For inoperative from cargo lamp switch only, GO TO 3
NO >> Replace the cargo lamp switch.
3.CHECK CARGO LAMP SWITCH CIRCUIT OPEN
2. Check continuity between BCM connector M18 terminal 31 and cargo lamp switch connector M71 termi-
nal 1.
BCM Cargo lamp switch

Continuity
M18 31 M71 1 Yes
YES >> GO TO 4
4.CHECK CARGO LAMP SWITCH GROUND CIRCUIT
1. Check continuity between cargo lamp switch connector M71 terminal 3 and ground.

M71 3 Ground Yes

5.CHECK CARGO LAMP SWITCH CIRCUIT SHORT A

B
M18 31 Ground No
YES >> GO TO 6
6.CHECK CARGO LAMP RELAY D
Check the cargo lamp relay. Refer to INL-82, "Component Inspection".

Is the inspection result normal? E
YES >> • For fixed OFF, GO TO 7
NO >> Replace the cargo lamp relay. F
7.CHECK CARGO LAMP RELAY CONTROL
While operating the cargo lamp switch, check voltage between BCM
connector M19 terminal 50 and ground. G
Cargo lamp
Connector Terminal — Voltage H
switch
ON 0V
M19 50 Ground
OFF Battery voltage
I
YES >> GO TO 8
NO >> GO TO 11 ALLIA0556GB
J
8.CHECK CARGO LAMP VOLTAGE
1. Disconnect the cargo lamp connector.
2. While operating the cargo lamp switch, check voltage between cargo lamp connector B161 terminal 3 and K
ground.
Cargo lamp INL

Connector Terminal — Voltage
switch
B161 3 Ground ON Battery voltage
Is the inspection result normal? M
YES >> GO TO 9
NO >> GO TO 10
N
9.CHECK CARGO LAMP GROUND CIRCUIT
1. While operating the cargo lamp switch, check voltage between cargo lamp connector B161 terminal 3 and
terminal 2. O
Terminal Terminal Cargo lamp

Connector Voltage
(+) (-) switch
P
B161 3 2 ON Battery voltage
YES >> Replace cargo lamp.

and ground.
Cargo lamp relay

Voltage
YES >> Repair harness or connectors between cargo lamp relay
and cargo lamp.
NO >> Repair harness or connector between splice and cargo AWLIA0810ZZ
lamp relay.
and ground.
Cargo lamp relay

Voltage
YES >> GO TO 12
AWLIA0812ZZ
12.CHECK CARGO LAMP RELAY CONTROL CIRCUIT OPEN

2. Check continuity between BCM connector M19 terminal 50 and cargo lamp relay connector M165 termi-
nal 1.
BCM Cargo lamp relay

Continuity
M19 50 M165 1 Yes
13.CHECK CARGO LAMP RELAY CONTROL CIRCUIT SHORT

M19 50 Ground No
YES >> Replace BCM after making sure the cargo lamp power supply circuit is not shorted to voltage.
Refer to BCS-49, "Removal and Installation".
Component Inspection INFOID:0000000009480178
CARGO LAMP SWITCH


2. Disconnect cargo lamp switch connector. A
3. Check continuity between cargo lamp switch terminals 1and 3.
Cargo lamp switch B

Condition Continuity
Terminal
ON Yes
1−3 C
OFF No
AWLIA0804ZZ
YES >> Inspection End D
NO >> Replace cargo lamp switch.
CARGO LAMP RELAY
1.CHECK CARGO LAMP RELAY E

2. Disconnect cargo lamp relay.
F
3. Supply power to terminal 2 and ground to terminal 1 of the cargo
lamp relay.
4. Check continuity between cargo lamp relay terminals 3 and 5.
G
Power and ground supplied to terminals 1 and 2 Yes
3 5 H
No power and ground supplied No
Is the inspection result normal? SEF497Y
YES >> Inspection End I

NO >> Replace cargo lamp relay.
INL

< ECU DIAGNOSIS INFORMATION > [WITHOUT POWER DOOR LOCKS]
ECU DIAGNOSIS INFORMATION

Reference Value INFOID:0000000010229407
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob relative signal strength
VALUES ON THE DIAGNOSIS TOOL

Ignition switch OFF or ON Off
ACC ON SW
Ignition switch ACC On
A/C switch OFF Off
AIR COND SW
A/C switch ON On
AIR PRESS FL Front left tire air pressure value kPa, kg/cm2, psi
AIR PRESS FR Front right tire air pressure value kPa, kg/cm2, psi
AIR PRESS RL Rear left tire air pressure value kPa, kg/cm2, psi
AIR PRESS RR Rear right tire air pressure value kPa, kg/cm2, psi
AUTO LIGHT SW
Lighting switch AUTO On
Brake pedal released Off
BRAKE SW
Brake pedal applied On
Seat belt buckle unfastened Off
BUCKLE SW
Seat belt buckle fastened On
Buzzer in combination meter OFF Off
BUZZER
Buzzer in combination meter ON On
Cargo lamp switch OFF Off
CARGO LAMP SW
Cargo lamp switch ON On
CDL LOCK SW
Press door lock/unlock switch to the LOCK side On
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side On
Front door RH closed Off
DOOR SW-AS
Front door RH opened On
Front door LH closed Off
DOOR SW-DR
Front door LH opened On
Rear door LH closed Off
DOOR SW-RL
Rear door LH opened On
Rear door RH closed Off
DOOR SW-RR
Rear door RH opened On

A
Blower motor fan switch OFF Off
FAN ON SIG
Blower motor fan switch ON On
Front fog lamp switch OFF Off B
FR FOG SW
Front fog lamp switch ON On
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On C
FR WIPER LOW
Front wiper switch LO On
D
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off E
FR WIPER INT
Front wiper switch INT On
Any position other than front wiper stop position Off
FR WIPER STOP F
Front wiper stop position On
When hazard switch is not pressed Off
HAZARD SW
When hazard switch is pressed On G
HEAD LAMP SW 1
H
HEAD LAMP SW 2
High beam switch OFF Off I
HI BEAM SW
High beam switch HI On
ID registration of front left tire incomplete YET
ID REGST FL1 J
ID registration of front left tire complete DONE
ID registration of front right tire incomplete YET
ID REGST FR1
ID registration of front right tire complete DONE
K
ID registration of rear left tire incomplete YET
ID REGST RL1
ID registration of rear left tire complete DONE
ID registration of rear right tire incomplete YET INL
ID REGST RR1
ID registration of rear right tire complete DONE
IGN ON SW M
IGN SW CAN
Ignition switch ON On N
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
Door key cylinder LOCK position Off
KEY CYL LK-SW O
Door key cylinder other than LOCK position On
Door key cylinder UNLOCK position Off
KEY CYL UN-SW
Door key cylinder other than UNLOCK position On P
Mechanical key is removed from key cylinder Off
KEY ON SW
Mechanical key is inserted to key cylinder On
LOCK button of key fob is not pressed Off
KEYLESS LOCK
LOCK button of key fob is pressed On

PANIC button of key fob is not pressed Off
KEYLESS PANIC
PANIC button of key fob is pressed On
UNLOCK button of key fob is not pressed Off
KEYLESS UNLOCK
UNLOCK button of key fob is pressed On
LIGHT SW 1ST
Lighting switch 1st On
• Ignition switch OFF or ACC
Off
OIL PRESS SW • Engine running
Bright outside of the vehicle Close to 5V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0V
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On
TURN SIGNAL L
Turn signal switch LH On
TURN SIGNAL R
Turn signal switch RH On
VEHICLE SPEED While driving Equivalent to speedometer reading
Low tire pressure warning lamp in combination meter OFF Off
WARNING LAMP
Low tire pressure warning lamp in combination meter ON On

Terminal Layout INFOID:0000000010229408
INL
P
LIIA2443E
Physical Values INFOID:0000000010229409


output switch
Ignition keyhole illumi- Door is locked (SW OFF) Battery voltage

1 BR Output OFF
nation Door is unlocked (SW ON) 0V

2 P Input ON
SKIA5291E

3 SB Input ON
SKIA5292E

4 V Input ON
SKIA5291E
Combination switch
5 L
input 2

Input ON
6 R
input 1
SKIA5292E
Front door lock as- ON (open, 2nd turn) Momentary 1.5V

7 GR sembly LH (key cylin- Input
der switch) unlock OFF (closed) 0V
OFF
Front door lock as- On (open) Momentary 1.5V
8 SB sembly LH (key cylin- Input
der switch) lock OFF (closed) 0V
OFF (brake pedal is not de-

0V
pressed)
9 LG Brake sw Input OFF
ON (brake pedal is de-
Battery voltage
pressed)
Ignition switch (ACC ACC or
11 G/B Input Ignition switch ACC or ON Battery voltage
or ON) ON
Front door switch RH
ON (open) 0V
(All)
12 LG Input OFF
per RH (King Cab)
er RH (King Cab)


output switch
Rear door switch RH ON (open) 0V

13 L
(Crew Cab)
Input OFF B
Tire pressure warning
15 W Input OFF — 5V
check connector
C
18 BR receiver and optical Output OFF — 0V
sensor (Ground)
D

E
19 V receiver (power sup- Output OFF Ignition switch OFF
ply)
F
LIIA1893E
G
Stand-by (keyfob buttons re-
leased)
H
Remote keyless entry LIIA1894E
20 G receiver signal (Sig- Input OFF
nal) I
When remote keyless entry

receiver receives signal from
keyfob (keyfob buttons J
pressed)
LIIA1895E
K
OFF →
21 GR NATS antenna amp. Input Ignition switch (OFF → ON) ON: Pointer of tester should
ON
move.
INL
Security indicator Goes OFF → illuminates (Ev-
23 G Output OFF Battery voltage → 0V
lamp ery 2.4 seconds)
OFF → M
25 BR NATS antenna amp. Input Ignition switch (OFF → ON) ON: Pointer of tester should
ON
move.
Compressor ON sig- A/C switch OFF 5V

27 W Input ON N
nal A/C switch ON 0V
Front blower motor OFF Battery voltage
28 R Front blower monitor Input ON
Front blower motor ON 0V O
ON 0V
29 G Hazard switch Input OFF
OFF 5V
P
ON 0V
31 GR Cargo lamp switch Input OFF
OFF Battery voltage


output switch

32 BG Output ON
SKIA5291E

33 GR Output ON
SKIA5292E

34 G Output ON
SKIA5291E
Combination switch
35 BR
output 2

Output ON
36 LG
output 1
SKIA5292E
Key inserted Battery voltage

37 B Key switch Input OFF
Key removed 0V
38 W/R Ignition switch (ON) Input ON — Battery voltage
39 L CAN-H — — — —
40 P CAN-L — — — —
Rear window defogger switch
0V
Rear window defogger ON
41 Y Input ON
switch Rear window defogger switch
5V
OFF
ON (lock) 0V
45 V Lock switch Input OFF
OFF Battery voltage
ON (unlock) 0V
46 LG Unlock switch Input OFF
OFF Battery voltage
Front door switch LH
ON (open) 0V
(All)
47 GR Input OFF
per LH (King Cab)
er LH (King Cab)


output switch
Rear door switch LH ON (open) 0V

48 P
(Crew Cab)
Input OFF B
Any door open (ON) 0V
50 P Cargo lamp Output OFF
All doors closed (OFF) Battery voltage C
D
Trailer turn signal
51 BG Output ON Turn right ON
(right)
E
SKIA3009J
52 LG Trailer turn signal (left) Output ON Turn left ON

G
SKIA3009J
H
10 minutes after ignition
OFF 0V
56 R/Y Battery saver output Output switch is turned OFF
ON — Battery voltage
I
57 R/Y Battery power supply Input — — Battery voltage
When optical sensor is illumi-
3.1V or more
nated
58 W Optical sensor Input ON J
When optical sensor is not illu-
0.6V or less
minated
Front door lock as- OFF (neutral) 0V

59 GR Output OFF K
sembly LH (unlock) ON (unlock) Battery voltage
INL
60 LG Turn signal (left) Output ON Turn left ON

M
SKIA3009J
61 G Turn signal (right) Output ON Turn right ON O
SKIA3009J P
Interior room/map Any door ON (open) 0V
63 BR Output OFF
lamp switch OFF (closed) Battery voltage
All door lock actuators OFF (neutral) 0V

65 V Output OFF
(lock) ON (lock) Battery voltage


output switch
Front door lock actua- OFF (neutral) 0V
tor RH, rear door lock
66 L Output OFF
actuators LH/RH (un- ON (unlock) Battery voltage
lock)
67 B Ground Input ON — 0V
Battery voltage
tion switch OFF
681 O
supply (RAP)
Output — 0V
nition switch OFF
operates
Battery voltage
tion switch OFF
682 SB
supply (RAP)
Output — 0V
nition switch OFF
operates
69 P Power window power
Output OFF — Battery voltage
supply (BAT)
70 W Battery power supply Input OFF — Battery voltage
1: King cab
2: Crew cab
Fail Safe INFOID:0000000010229410
Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.
Display contents of CONSULT Fail-safe Cancellation

When the BCM re-establishes communication with the other mod-
U1000: CAN COMM CIRCUIT Inhibit engine cranking
ules.
DTC Inspection Priority Chart INFOID:0000000010229411
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 • U1000: CAN COMM CIRCUIT
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
2
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM

Priority DTC
A
• C1729: VHCL SPEED SIG ERR
3
• C1735: IGNITION SIGNAL
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR B
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
C
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL D
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
4
• C1716: [PRESSDATA ERR] FL E
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL F
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL G
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
H
DTC Index INFOID:0000000010229412
NOTE: I
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again. J
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again. K
Low tire pressure

warning lamp ON INL
No DTC is detected.
further testing — — —
may be required.
M
U1000: CAN COMM CIRCUIT — — BCS-26
B2190: NATS ANTTENA AMP — — SEC-18
B2191: DIFFERENCE OF KEY — — SEC-21 N
B2192: ID DISCORD BCM-ECM — — SEC-22
B2193: CHAIN OF BCM-ECM — — SEC-24
O
C1708: [NO DATA] FL — X WT-15
C1709: [NO DATA] FR — X WT-15
C1710: [NO DATA] RR — X WT-15 P
C1711: [NO DATA] RL — X WT-15
C1712: [CHECKSUM ERR] FL — X WT-17
C1713: [CHECKSUM ERR] FR — X WT-17
C1714: [CHECKSUM ERR] RR — X WT-17
C1715: [CHECKSUM ERR] RL — X WT-17

Low tire pressure
warning lamp ON
C1716: [PRESSDATA ERR] FL — X WT-19
C1717: [PRESSDATA ERR] FR — X WT-19
C1718: [PRESSDATA ERR] RR — X WT-19
C1719: [PRESSDATA ERR] RL — X WT-19
C1720: [CODE ERR] FL — X WT-17
C1721: [CODE ERR] FR — X WT-17
C1722: [CODE ERR] RR — X WT-17
C1723: [CODE ERR] RL — X WT-17
C1724: [BATT VOLT LOW] FL — X WT-17
C1725: [BATT VOLT LOW] FR — X WT-17
C1726: [BATT VOLT LOW] RR — X WT-17
C1727: [BATT VOLT LOW] RL — X WT-17
C1729: VHCL SPEED SIG ERR — X WT-21
C1735: IGNITION SIGNAL — X WT-22

INTERIOR ROOM LAMP
< WIRING DIAGRAM > [WITHOUT POWER DOOR LOCKS]
WIRING DIAGRAM A
INTERIOR ROOM LAMP
Wiring Diagram - Without Power Door Lock System INFOID:0000000009480185
B
INL
ABLWA2385GB

INTERIOR ROOM LAMP
ABLWA2386GB

INTERIOR ROOM LAMP
INL
ABLIA5627GB

INTERIOR ROOM LAMP
ABLIA5628GB

INTERIOR ROOM LAMP
INL
ABLIA5629GB

INTERIOR ROOM LAMP
ABLIA5630GB

INTERIOR ROOM LAMP
INL
ABLIA5631GB

INTERIOR ROOM LAMP
ABLIA5632GB

INTERIOR ROOM LAMP
INL
ABLIA5675GB

ILLUMINATION
ILLUMINATION
Wiring Diagram INFOID:0000000010230396
ABLWA2390GB

ILLUMINATION
INL
ABLWA2399GB

ILLUMINATION
ABLWA2030GB

ILLUMINATION
INL
ABLIA5647GB

ILLUMINATION
ABLIA5648GB

ILLUMINATION
INL
ABLIA5691GB

ILLUMINATION
ABLIA5669GB

ILLUMINATION
INL
ABLIA5649GB

ILLUMINATION
ABLIA5692GB

ILLUMINATION
INL
ABLIA5650GB

< SYMPTOM DIAGNOSIS > [WITHOUT POWER DOOR LOCKS]
SYMPTOM DIAGNOSIS
Symptom Table INFOID:0000000009480187
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom Possible cause Inspection item

interior room lamps do not turn ON/OFF and each interior room lamp
Interior room lamp
• Room lamp 2nd row • Harness between each interior
Refer to INL-78.
• Front room/map lamp assembly room lamp and door switches
• Door switches
and cargo lamp relay
• Harness between cargo lamp relay
Cargo lamp control circuit
Cargo lamp does not turn ON/OFF and cargo lamp
Refer to INL-80.
• Harness between BCM and cargo
lamp relay
• BCM

PRECAUTIONS
< PRECAUTION > [WITHOUT POWER DOOR LOCKS]
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000010126947
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS H
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a I
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the J
battery and wait at least three minutes before performing any service.
Precaution for Work INFOID:0000000009480189
K
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it. INL
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one. M
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
N
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
- Oily dirt: O
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off. P
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.

PREPARATION
< PREPARATION > [WITHOUT POWER DOOR LOCKS]
PREPARATION
PREPARATION
Special Service Tool INFOID:0000000009480190
The actual shape of the tools may differ from those illustrated here.
Tool number Description
(TechMate No.)
Tool name
— Removing trim components
(J-46534)
Trim Tool Set
AWJIA0483ZZ

INTERIOR ROOM LAMP
< REMOVAL AND INSTALLATION > [WITHOUT POWER DOOR LOCKS]
REMOVAL AND INSTALLATION A

INTERIOR ROOM LAMP
B
FRONT ROOM/MAP LAMP ASSEMBLY (IF EQUIPPED)

Removal C
The front room/map lamp assembly is replaced as part of the roof
console. Refer to INT-25, "Removal and Installation".
: Front D
: Metal clip
F
AWLIA0867ZZ
Installation
Installation is in the reverse order of removal. G

1. Using a suitable tool (A), remove the front room/map lamp RH H
and/or LH lenses (1) as necessary.
: Front
: Pawl I
2. Release one side of the bulb (2) from the tab using a suitable
tool, then pull straight downward to remove.
J
Front room/ : 12V - 8W
map lamp as-
sembly bulb
K
INL
N
AWLIA1667ZZ
3. Install the new bulb into the socket tabs. O

4. Install the front room/map lamp lens(es).
VANITY LAMP P
Removal

INTERIOR ROOM LAMP
The vanity lamp is replaced as part of the sun visor assembly. Refer
to INT-25, "Removal and Installation".
ALLIA0583ZZ
Installation
Bulb Replacement
The vanity mirror lamp bulb is replaced as part of the sun visor assembly. Refer to INT-25, "Removal and
Installation".
ROOM LAMP 2ND ROW
Removal
1. Using a suitable tool (A), release the pawls and remove the
room lamp lens (1).
: Pawl
2. Remove room lamp screws (2).
3. Disconnect the harness connector from the room lamp and
remove.
AWLIA1680ZZ
Installation
1. Using a suitable tool, release the pawls and remove the room lamp lens.
2. Release the room lamp bulb retainers (1), then pull bulb (2)
straight out to remove.
3. Install the bulb (2) securely into the room lamp bulb retainers (1).
Room lamp bulb : 12V - 8W
ALLIA0326ZZ

INTERIOR ROOM LAMP
4. Install the room lamp lens. A
INL

ILLUMINATION
ILLUMINATION
ILLUMINATION CONTROL SWITCH

Removal
The illumination control switch is replaced as a part of the combina-
tion meter. Refer to MWI-90, "Removal and Installation".
LKIA0579E
Installation
SHIFT SELECTOR FINISHER LAMP
Removal
2. Rotate shift selector finisher lamp socket (2) with bulb (3) coun-
terclockwise, then pull away from finisher (1).
ALLIA0590ZZ
Installation
Bulb Replacement
2. Remove shift selector finisher lamp socket (1), then pull bulb (2)
straight out away from socket.
3. Install the bulb (2) into the shift selector finisher socket (1).
AT finisher lamp bulb : 12V - 3W
ALLIA0321ZZ
4. Install shift selector finisher in center console. Refer to IP-25, "Removal and Installation".

BULB SPECIFICATIONS
< SERVICE DATA AND SPECIFICATIONS (SDS) [WITHOUT POWER DOOR LOCKS]
SERVICE DATA AND SPECIFICATIONS (SDS) A

BULB SPECIFICATIONS
Bulb Specifications INFOID:0000000009480193
B
Item Wattage (W)*

C
Front room/map lamp (if equipped) 8
Vanity lamp –
Room lamp 2nd row 8 D
Shift selector finisher lamp 3
*: Always check with the Parts Department for the latest parts information.
E
INL

Interior Lighting System: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Interior Lighting System: Section

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

INTERIOR ROOM LAMP CONTROL SYSTEM Description ...............................................................18

COMMON ITEM ......................................................... 11 ECU DIAGNOSIS INFORMATION .............. 26

Revision: May 2014 INL-1 2014 Frontier

DIAGNOSIS AND REPAIR WORKFLOW ......... 68 PRECAUTION ........................................... 115

DTC/CIRCUIT DIAGNOSIS ......................... 78

Revision: May 2014 INL-2 2014 Frontier

Revision: May 2014 INL-3 2014 Frontier

Revision: May 2014 INL-4 2014 Frontier

Check the operation of each part.

Revision: May 2014 INL-5 2014 Frontier

System Description INFOID:0000000009480125

INTERIOR LAMP BATTERY SAVER CONTROL

Revision: May 2014 INL-6 2014 Frontier

Revision: May 2014 INL-7 2014 Frontier

Component Description INFOID:0000000009480127

Part name Description

Revision: May 2014 INL-8 2014 Frontier

System Description INFOID:0000000009480129

Revision: May 2014 INL-9 2014 Frontier

Component Description INFOID:0000000009480131

Part name Description

Revision: May 2014 INL-10 2014 Frontier

Direct Diagnostic Mode

CAN Diag Support Mntr

System Sub System I

Door lock DOOR LOCK × × ×

Revision: May 2014 INL-11 2014 Frontier

Monitor Item [Unit] Description

Test Item Description

Support Item Setting Description

Revision: May 2014 INL-12 2014 Frontier

Monitor Item [Unit] Description A

DOOR SW-AS [On/Off] Indicates condition of front door switch RH.

Test item Description

Revision: May 2014 INL-13 2014 Frontier

Regarding Wiring Diagram information, refer to BCS-43, "Wiring Diagram".

1. CHECK FUSES AND FUSIBLE LINK

Terminal No. Signal name Fuses and fusible link No.

Terminals Power Voltage (V) (Ap-

Revision: May 2014 INL-14 2014 Frontier

Revision: May 2014 INL-15 2014 Frontier

1.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY FUNCTION

OFF : Interior room lamp OFF

1.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY OUTPUT

(+) Test item

Is the inspection result normal?

Revision: May 2014 INL-16 2014 Frontier

BCM Each interior room lamp

3.CHECK BATTERY SAVER OUTPUT/POWER SUPPLY SHORT CIRCUIT

Connector Terminal — Continuity G

Revision: May 2014 INL-17 2014 Frontier

ON : Interior room lamp gradual brightening

1.CHECK INTERIOR ROOM LAMP CONTROL OUTPUT

Revision: May 2014 INL-18 2014 Frontier

3.CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT

Connector Terminal — Continuity J

Revision: May 2014 INL-19 2014 Frontier

1.CHECK CARGO LAMP OPERATION

BCM Cargo lamp switch

Connector Terminal — Continuity

Revision: May 2014 INL-20 2014 Frontier