Def PDF

DRIVER CONTROLS
DEF
A
B
SECTION
DEFOGGER C
E
CONTENTS
PRECAUTION ............................................... 3 WIRING DIAGRAM ...................................... 11 F
PRECAUTIONS ................................................... 3 REAR WINDOW DEFOGGER SYSTEM .......... 11

Precaution for Supplemental Restraint System Wiring Diagram ........................................................11 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 3 BASIC INSPECTION ................................... 16
SYSTEM DESCRIPTION .............................. 4 DIAGNOSIS AND REPAIR WORK FLOW ....... 16 H

Work Flow ................................................................16
COMPONENT PARTS ........................................ 4
Component Parts Location ........................................ 4 DTC/CIRCUIT DIAGNOSIS ......................... 19
I
Component Description ............................................. 4
REAR WINDOW DEFOGGER SWITCH ........... 19
SYSTEM .............................................................. 5 Description ...............................................................19
System Diagram ........................................................ 5 Component Function Check ....................................19 J
System Description ................................................... 5 Diagnosis Procedure ...............................................19
Component Inspection .............................................20
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
REAR WINDOW DEFOGGER RELAY ............. 21 K
GENT KEY SYSTEM) .......................................... 6
Description ...............................................................21
COMMON ITEM ........................................................... 6 Component Function Check ....................................21
COMMON ITEM : CONSULT Function (BCM - Diagnosis Procedure ...............................................21 DEF
COMMON ITEM) ....................................................... 6 Component Inspection .............................................22
REAR DEFOGGER ..................................................... 7 REAR WINDOW DEFOGGER POWER SUP-
REAR DEFOGGER : CONSULT Function (BCM - M
PLY AND GROUND CIRCUIT .......................... 23
REAR DEFOGGER) ................................................. 7 Description ...............................................................23
Component Function Check ....................................23
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- N
Diagnosis Procedure ...............................................23
TELLIGENT KEY SYSTEM) ................................ 8 Component Inspection .............................................24
COMMON ITEM ........................................................... 8
DRIVER SIDE DOOR MIRROR DEFOGGER ... 25 O
COMMON ITEM : CONSULT Function (BCM -
Description ...............................................................25
COMMON ITEM) ....................................................... 8
Component Function Check ....................................25
REAR DEFOGGER ..................................................... 9 Diagnosis Procedure ...............................................25
Component Inspection .............................................26 P
REAR DEFOGGER : CONSULT Function (BCM -
REAR DEFOGGER) ................................................. 9
PASSENGER SIDE DOOR MIRROR DEFOG-
ECU DIAGNOSIS INFORMATION .............. 10 GER ................................................................... 27
Description ...............................................................27
BCM ....................................................................10 Component Function Check ....................................27
List of ECU Reference ............................................ 10 Diagnosis Procedure ...............................................27
Revision: April 2013 DEF-1 2014 Versa Sedan

Component Inspection ............................................ 28 DRIVER SIDE DOOR MIRROR DEFOGGER
DOES NOT OPERATE. ..................................... 32
SYMPTOM DIAGNOSIS ............................. 29 Diagnosis Procedure ............................................... 32
REAR WINDOW DEFOGGER AND DOOR PASSENGER SIDE DOOR MIRROR DEFOG-
MIRROR DEFOGGER DO NOT OPERATE. ..... 29 GER DOES NOT OPERATE. ............................ 33
Diagnosis Procedure .............................................. 29 Diagnosis Procedure ............................................... 33
REAR WINDOW DEFOGGER DOES NOT REAR WINDOW DEFOGGER SWITCH DOES
OPERATE BUT BOTH OF DOOR MIRROR NOT LIGHT, BUT REAR WINDOW DEFOG-
DEFOGGER OPERATE. ................................... 30 GER OPERATES ............................................... 34
Diagnosis Procedure .............................................. 30 Diagnosis Procedure ............................................... 34
BOTH DOORS MIRROR DEFOGGER DON’T REMOVAL AND INSTALLATION .............. 35
OPERATE BUT REAR WINDOW DEFOG-
GER OPERATES ............................................... 31 FILAMENT ......................................................... 35
Diagnosis Procedure .............................................. 31 Inspection and Repair ............................................. 35

PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000009268308
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS H
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a I
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the J
battery, and wait at least 3 minutes before performing any service.
DEF

COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000009268309
ALLIA1031ZZ
1. BCM (view with instrument panel re- 2. Rear window defogger relay (view 3. Front air control (rear window defog-
moved) with instrument panel removed) ger switch)
4. A. Rear window defogger power 5. Door mirror (door mirror defogger) (if
connector equipped)
B. Rear window defogger ground
connector
Component Description INFOID:0000000009268310
• Operates the rear window defogger with the operation of rear window defogger switch.
BCM
• Performs the timer control of rear window defogger.
Rear window defogger relay • Operates the rear window defogger and the door mirror defogger* with the control signal from
BCM.
Front air control (rear window • The rear window defogger switch is turned ON.
defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Rear window defogger
the rear window from fogging up.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Door mirror defogger* the door mirror from fogging up.
*:
With heated mirrors

SYSTEM
SYSTEM
A
System Diagram INFOID:0000000009268311
ALLIA1028GB
G
System Description INFOID:0000000009268312
H
Operation Description
• When rear window defogger switch is turned ON while ignition switch is ON, the front air control (rear win-
dow defogger switch) transmits rear window defogger switch signal to BCM.
• BCM turns rear window defogger relay ON when rear window defogger switch signal is received. I
• Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and
operate when rear window defogger relay turns ON.
• Rear window defogger ON is displayed when front air control receives signals. J
Timer function
• BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON while ignition switch is ON. It makes rear window defogger and door mirror defogger (with door K
mirror defogger) operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same reaction also occurs during timer operation, if the ignition switch DEF
is turned OFF.
INPUT/OUTPUT SIGNAL CHART M
Switch Input signal to BCM BCM function Actuator

Rear window defogger switch Defogger switch signal Rear window defogger and door Rear window defogger N
Ignition switch Ignition signal mirror defogger* control Door mirror defogger *
*: With door mirror defogger
O

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000009545880
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode Description

ECU identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
CAN DIAG SUPPORT MNTR

Self Diagnostic Result
System Sub System

ECU identification
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × × ×

Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITIONER ×
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×

REAR DEFOGGER
A
REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER) INFOID:0000000009545958
DATA MONITOR B
Monitor Item [Unit] Description

PUSH SW [On/Off] Indicates condition of push-button ignition switch. C
REAR DEF SW [On/Off] Indicates condition of rear window defogger switch.
ACTIVE TEST D
Test Item Description

REAR DEFOGGER This test is able to check rear window defogger operation [Off/On]. E
DEF

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000009545959
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode Description

ECU identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
CAN DIAG SUPPORT MNTR

Self Diagnostic Result
System Sub System

ECU identification
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × × ×

Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITIONER ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × ×
Signal buffer system SIGNAL BUFFER × ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×

REAR DEFOGGER
A
REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER) INFOID:0000000009545960
DATA MONITOR B
Monitor Item [Unit] Description

IGN ON SW [On/Off] Indicates condition of ignition switch ON position. C
ACC ON SW [On/Off] Indicates condition of ignition switch ACC position.
REAR DEF SW [On/Off] Indicates condition of rear window defogger switch.
D
RR DEF TIME [On/Off] Indicates condition of rear window defogger switch timer.
ACTIVE TEST
E
Test Item Description
REAR DEFOGGER This test is able to check rear window defogger operation [Off/On].
F
DEF

BCM
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference INFOID:0000000009268317
ECU Reference
BCS-28, "Reference Value"
BCS-45, "Fail-safe"
BCM (with Intelligent Key system)
BCS-47, "DTC Inspection Priority Chart"
BCS-48, "DTC Index"
BCS-93, "Reference Value"
BCS-104, "Fail-safe"
BCM (without Intelligent Key system)
BCS-104, "DTC Inspection Priority Chart"
BCS-105, "DTC Index"

REAR WINDOW DEFOGGER SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
Wiring Diagram INFOID:0000000009268318
B
DEF
ABLWA2172GB

< WIRING DIAGRAM >
ABLIA4867GB

< WIRING DIAGRAM >
DEF
ABLIA4868GB

< WIRING DIAGRAM >
ABLIA4869GB

< WIRING DIAGRAM >
DEF
ABLIA4870GB

DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION
Work Flow INFOID:0000000009268319
OVERALL SEQUENCE
JMKIA0101GB
DETAILED FLOW

1. GET INFORMATION FOR SYMPTOM A
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
B
>> GO TO 2
2. CHECK DTC
C
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
- Record DTC and freeze frame data (Print them out with CONSULT.)
- Erase DTC. D
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected? E
Symptom is described, DTC is displayed>>GO TO 3
Symptom is described, DTC is not displayed>>GO TO 4
Symptom is not described, DTC is displayed>>GO TO 5 F
3. CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT to the vehicle in “DATA MONITOR” mode and check real time diagnosis results. G
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5 H
4. CONFIRM THE SYMPTOM

Confirm the symptom described by the customer. I
Connect CONSULT to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
J
>> GO TO 6
5. PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again. K
At this time, always connect CONSULT to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-47, "DTC Inspection Priority Chart" (with Intelligent Key) or
BCS-104, "DTC Inspection Priority Chart" (without Intelligent Key) and determine trouble diagnosis order. DEF
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
M
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirma-
tion Procedure.
Is DTC detected? N
YES >> GO TO 8
NO >> Refer to GI-45, "Intermittent Incident".
6. PERFORM BASIC INSPECTION
O
Perform DEF-16, "Work Flow".

P
>> GO TO 7
7. DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to DEF-5, "System Description" based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 8
8. DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES >> GO TO 9
NO >> Check voltage of related BCM terminals using CONSULT.
9. REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 10
10. FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8
YES (Symptom remains)>>GO TO 6
NO >> Inspection End.

REAR WINDOW DEFOGGER SWITCH
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS A
Description INFOID:0000000009268320
B
• The rear window defogger is operated by pressing the rear window defogger switch ON.
• The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
C
Component Function Check INFOID:0000000009268321
1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION D

1. Turn ignition switch ON.
2. Check that the indicator lamp of rear window defogger illuminates with rear window defogger switch ON.
Is the inspection result normal? E
YES >> GO TO 2.
NO >> Refer to DEF-19, "Diagnosis Procedure".
2.CHECK REAR DEFOGGER ON STATUS F
1. Using CONSULT, select "BCM (REAR DEFOGGER)", then "DATA MONITOR" mode.
2. Select "REAR DEF SW" and monitor while pressing the rear DEF switch ON and OFF.
G
Monitored Item Condition Status
Rear DEF switch ON (LED ON) On H
REAR DEF SW
Rear DEF switch OFF (LED OFF) Off
Is the inspection result normal?
YES >> Inspection End. I
Diagnosis Procedure INFOID:0000000009268322
J
Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram".

K
1.CHECK BCM OUTPUT SIGNAL

DEF
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check voltage between front air control harness connector and ground.
M
(+)
Voltage (V)
Front air control (–)
(Approx.) N
Connector Terminal
M33 10 Ground Battery voltage
Is the inspection result normal? O
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT P
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front air control harness connector.

BCM Front air control

Continuity
Connector Terminal Connector Terminal
M18 (without Intelligent Key system) 10
M33 10 Yes
M97 (with Intelligent Key system) 15
3. Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal
Ground
No
YES >> Replace BCM. Refer to BCS-69, "Removal and Installation" (with Intelligent Key) or BCS-122,
"Removal and Installation" (without Intelligent Key).
NO >> Repair or replace harness.
3.CHECK GROUND CIRCUIT
Check continuity between front air control harness connector and ground.
Front air control

Continuity
Connector Terminal Ground
M33 8 Yes
YES >> GO TO 4.
4.CHECK REAR WINDOW DEFOGGER SWITCH
Refer to DEF-20, "Component Inspection".
YES >> Check intermittent incident. Refer to GI-45, "Intermittent Incident".
NO >> Replace front air control. Refer to HAC-48, "Removal and Installation".
Component Inspection INFOID:0000000009268323
1.CHECK REAR WINDOW DEFOGGER SWITCH

2. Disconnect front air control connector.
3. Check continuity between front air control terminals.
Front air control

Condition Continuity
Terminal
Pressed Yes
10 8 Rear window defogger switch
Released No
YES >> Inspection End.
NO >> Replace front air control. Refer to HAC-48, "Removal and Installation".

REAR WINDOW DEFOGGER RELAY
A
Power is supplied to the rear window defogger with BCM control. B

1.CHECK FUNCTION C
2. Check that an operation noise of rear window defogger relay can be heard when turning the rear window
defogger switch ON. D
YES >> Rear window defogger relay function is OK.
NO >> Refer to DEF-21, "Diagnosis Procedure" E

G
1.CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF and disconnect rear window defogger relay connector. H
3. Check voltage between rear window defogger relay harness connector and ground.
I
(+)
Voltage (V)
Rear window defogger relay (−)
(Approx.)
Connector Terminal J
M14 2 Ground Battery voltage
K
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK FUSE DEF
2. Check 10A fuse (No. 5).
Is the inspection result normal? M
YES >> Check ignition power supply circuit. Refer to PG-20, "Wiring Diagram — Ignition Power Supply —
".
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. N
3.CHECK REAR WINDOW DEFOGGER RELAY CONTROL CIRCUIT
2. Disconnect BCM connector. O
3. Check continuity between BCM harness connector and rear window defogger relay harness connector.
BCM Rear window defogger relay P

Continuity
Connector Terminal Connector Terminal
M14 1 Yes
4. Check continuity between BCM harness connector and ground.

BCM
Continuity
Connector Terminal
Ground
No
YES >> GO TO 4.
4.CHECK REAR WINDOW DEFOGGER RELAY
YES >> Replace BCM. Refer to BCS-69, "Removal and Installation" (with Intelligent Key) or BCS-122,
"Removal and Installation" (without Intelligent Key).
NO >> Replace rear window defogger relay.
Check continuity between terminal 3 and 5, 6 and 7.
Terminal Condition Continuity

12 V direct current supply between terminal 1
3 and 5, 6 Yes
and 2
and 7
No current supply No
SEF745U

REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
A
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window B
from fogging up.
1. CHECK REAR WINDOW DEFOGGER

Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch D
ON.
E
YES >> Rear window defogger is OK.
F
Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram". G
1. CHECK FUSES H
Check if any of the following fuses in fuse block (J/B) are blown.
COMPONENT PARTS AMPERE FUSE NO.

I
20A 9
Fuse block (J/B)
20A 11
Is the inspection result normal? J
YES >> GO TO 2
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2. CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT K

2. Check voltage between rear window defogger relay connector and ground. DEF
Terminals
(+) Condition of rear
Voltage (V)
M
window defogger
Rear window (–) (Approx.)
switch
defogger relay Terminal
connector N
ON Battery voltage
M14 3, 6 Ground
OFF 0
YES >> GO TO 3
NO >> Check the following:
• Rear window defogger relay. P
• Battery power supply circuit.
3. CHECK POWER SUPPLY CIRCUIT
2. Check voltage between rear window defogger connector and ground.

Terminals
(+) Condition of rear
Voltage (V)
window
Rear window (–) (Approx.)
defogger switch
defogger Terminal
connector
ON Battery voltage
B42 1 Ground
OFF 0
YES >> GO TO 4
NO >> GO TO 5
4. CHECK GROUND CIRCUIT
2. Disconnect rear window defogger.
3. Check continuity between rear window defogger connector and ground.
Rear window defogger connector Terminal Continuity

Ground
B46 2 Yes
YES >> GO TO 6
5. CHECK HARNESS CONTINUITY
2. Disconnect rear window defogger relay connector and rear window defogger.
3. Check continuity between rear window defogger relay connector and rear window defogger connector.
Rear window
Rear window defogger
defogger relay Terminal Terminal Continuity
connector
connector
M14 3, 6 B42 1 Yes
NO >> Replace or repair harness.
6. CHECK FILAMENT
Check filament.
YES >> Refer to GI-45, "Intermittent Incident".
NO >> Repair filament. Refer to DEF-35, "Inspection and Repair".
1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-35, "Inspection and Repair".
NO >> Repair filament. Refer to DEF-35, "Inspection and Repair".

DRIVER SIDE DOOR MIRROR DEFOGGER
A
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
C
1. CHECK DOOR MIRROR DEFOGGER LH
Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch
ON. D
YES >> Door mirror defogger is OK.
NO >> Refer to DEF-25, "Diagnosis Procedure". E

G
1. Turn ignition switch OFF. H
2. Disconnect door mirror LH.
4. Check voltage between door mirror LH connector and ground.
I
Terminals
Condition of
(+) rear window Voltage (V)
J
(–) defogger (Approx.)
Door mirror LH
Terminal switch
connector
ON Battery voltage K
D4 3 Ground
OFF 0
YES >> GO TO 2 DEF
2. CHECK GROUND CIRCUIT M
2. Check continuity between door mirror LH connector and ground.
N
Door mirror LH connector Terminal Continuity
Ground
D4 2 Yes
YES >> GO TO 3
3. CHECK DOOR MIRROR DEFOGGER LH P
Check door mirror defogger LH.

YES >> GO TO 4
NO >> Replace door mirror. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installation".

4. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-45, "Intermittent Incident".
YES >> Check the following.
• Fuse block (J/B).
NO >> Repair or replace the malfunctioning parts.

2. Disconnect door mirror LH.
3. Check continuity between door mirror terminals.
Terminal Continuity
3 2 Yes
NO >> Replace door mirror LH. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
tion".

PASSENGER SIDE DOOR MIRROR DEFOGGER
A
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror B
from fogging up.
C
1.CHECK DOOR MIRROR DEFOGGER RH
Check that the heating wire of door mirror defogger RH is heated when turning the rear window defogger
switch ON. D
YES >> Door mirror defogger RH is OK.
NO >> Refer to DEF-27, "Diagnosis Procedure". E

G
1. Turn ignition switch OFF. H
2. Disconnect door mirror RH.
4. Check voltage between door mirror RH connector and ground.
I
Terminals
Condition of rear
(+) Voltage (V)
window defogger J
(–) (Approx.)
Door mirror RH switch
Terminal
connector
ON Battery voltage K
D107 3 Ground
OFF 0
YES >> GO TO 2 DEF
2. CHECK GROUND CIRCUIT M
2. Check continuity between door mirror RH connector and ground.
N
Door mirror RH connector Terminal Continuity
Ground
D107 2 Yes
YES >> GO TO 3
3. CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER P
Check door mirror defogger RH.

YES >> GO TO 4
NO >> Replace door mirror RH. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
tion".

4. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-45, "Intermittent Incident".
YES >> Check the following.
• Fuse block (J/B).
1. CHECK DOOR MIRROR DEFOGGER RH

2. Disconnect door mirror RH.
3. Check continuity between door mirror terminals.
Terminal Continuity
3 2 Yes
NO >> Replace door mirror RH. Refer to MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
tion".

REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPER-
ATE.
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT
OPERATE.
B
1. CHECK REAR WINDOW DEFOGGER SWITCH C

Check rear window defogger switch.
Refer to DEF-19, "Component Function Check".
Is the inspection result normal? D
YES >> GO TO 2
2. CHECK REAR WINDOW DEFOGGER RELAY E
Check rear window defogger relay.

Refer to DEF-21, "Component Function Check". F
YES >> GO TO 3
NO >> Repair or replace the malfunctioning parts. G
3. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
Check rear window defogger power supply and ground circuit.
Refer to DEF-23, "Component Function Check". H
NO >> Repair or replace the malfunctioning parts. I
DEF

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIR-
ROR DEFOGGER OPERATE.
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR
MIRROR DEFOGGER OPERATE.
1. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

Check rear window defogger power supply and ground circuit.

BOTH DOORS MIRROR DEFOGGER DON’T OPERATE BUT REAR WINDOW
DEFOGGER OPERATES
BOTH DOORS MIRROR DEFOGGER DON’T OPERATE BUT REAR WIN-
A
DOW DEFOGGER OPERATES
B
1. CHECK DOOR MIRROR DEFOGGER FUSE
Check if the following fuse in fuse block (J/B) is blown.
C
COMPONENT PARTS AMPERE FUSE NO.
Fuse block (J/B) 10A 1
D
YES >> GO TO 2
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. E
2. CHECK BOTH DOOR MIRROR DEFOGGER
1. Check door mirror LH. Refer to DEF-25, "Component Function Check".
2. Check door mirror RH. Refer to DEF-27, "Component Function Check". F
NO >> Repair or replace the malfunctioning parts. G
DEF

DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.

Check door mirror defogger LH.

PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
A
1. CHECK DOOR MIRROR DEFOGGER RH B

Check door mirror defogger RH.
Is the inspection result normal? C
D
DEF

REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WIN-
DOW DEFOGGER OPERATES
1. CHECK FRONT AIR CONTROL (REAR WINDOW DEFOGGER SWITCH)

Check that the front air control (rear window defogger switch) is operating normally.

FILAMENT
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
FILAMENT
Inspection and Repair INFOID:0000000009268346
B
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg- C
ative probe. Then press the foil against the wire with your finger.
SEL122R F
2. Attach probe circuit tester (in Volt range) to middle portion of

each filament. G
SEL263
J
3. If a filament is burned out, circuit tester registers 0 or battery
voltage.
4. To locate burned out point, move probe to left and right along fil- K
ament. Test needle will swing abruptly when probe passes the
point.
DEF
SEL265
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)

FILAMENT
< REMOVAL AND INSTALLATION >
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
NOTE:
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
PIIA0215E
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
CAUTION:
Do not touch repaired area while test is being conducted.
SEL012D
5. Apply a constant stream of hot air directly to the repaired area

for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
NOTE:
If a heat gun is not available, let the repaired area dry for 24
hours.
SEL013D

Def PDF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Def PDF

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

PRECAUTIONS ................................................... 3 REAR WINDOW DEFOGGER SYSTEM .......... 11

SYSTEM DESCRIPTION .............................. 4 DIAGNOSIS AND REPAIR WORK FLOW ....... 16 H

Revision: April 2013 DEF-1 2014 Versa Sedan

Revision: April 2013 DEF-2 2014 Versa Sedan

Revision: April 2013 DEF-3 2014 Versa Sedan

Component Description INFOID:0000000009268310

Revision: April 2013 DEF-4 2014 Versa Sedan

System Description INFOID:0000000009268312

INPUT/OUTPUT SIGNAL CHART M

Switch Input signal to BCM BCM function Actuator

Revision: April 2013 DEF-5 2014 Versa Sedan

Direct Diagnostic Mode Description

Direct Diagnostic Mode

CAN DIAG SUPPORT MNTR

System Sub System

Door lock DOOR LOCK × × × ×

Revision: April 2013 DEF-6 2014 Versa Sedan

Monitor Item [Unit] Description

Test Item Description

Revision: April 2013 DEF-7 2014 Versa Sedan

Direct Diagnostic Mode Description

Direct Diagnostic Mode

CAN DIAG SUPPORT MNTR

System Sub System

Door lock DOOR LOCK × × × ×

Revision: April 2013 DEF-8 2014 Versa Sedan

Monitor Item [Unit] Description

Revision: April 2013 DEF-9 2014 Versa Sedan

Revision: April 2013 DEF-10 2014 Versa Sedan

Revision: April 2013 DEF-11 2014 Versa Sedan

Revision: April 2013 DEF-12 2014 Versa Sedan

Revision: April 2013 DEF-13 2014 Versa Sedan

Revision: April 2013 DEF-14 2014 Versa Sedan

Revision: April 2013 DEF-15 2014 Versa Sedan

Revision: April 2013 DEF-16 2014 Versa Sedan

4. CONFIRM THE SYMPTOM

Perform DEF-16, "Work Flow".

Revision: April 2013 DEF-18 2014 Versa Sedan

1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION D

Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram".

1.CHECK BCM OUTPUT SIGNAL

Revision: April 2013 DEF-19 2014 Versa Sedan

BCM Front air control

Front air control

1.CHECK REAR WINDOW DEFOGGER SWITCH

Front air control

Revision: April 2013 DEF-20 2014 Versa Sedan

Power is supplied to the rear window defogger with BCM control. B

Diagnosis Procedure INFOID:0000000009268326

Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram".

BCM Rear window defogger relay P

Revision: April 2013 DEF-21 2014 Versa Sedan

Check continuity between terminal 3 and 5, 6 and 7.

Terminal Condition Continuity

Revision: April 2013 DEF-22 2014 Versa Sedan

1. CHECK REAR WINDOW DEFOGGER

Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram". G

COMPONENT PARTS AMPERE FUSE NO.

1. Turn ignition switch ON.

Revision: April 2013 DEF-23 2014 Versa Sedan

Rear window defogger connector Terminal Continuity