Wiper & Washer: Section
Wiper & Washer: Section
Wiper & Washer: Section
SECTION
WIPER & WASHER
WW B
E
CONTENTS
BASIC INSPECTION .................................... 3 FRONT WIPER MOTOR HI CIRCUIT ............... 17 F
Component Function Check ....................................17
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 Diagnosis Procedure ...............................................17
Work Flow ................................................................. 3 G
FRONT WIPER AUTO STOP SIGNAL CIR-
FUNCTION DIAGNOSIS ............................... 4 CUIT .................................................................. 19
Component Function Check ....................................19
FRONT WIPER AND WASHER SYSTEM .......... 4 Diagnosis Procedure ...............................................19
H
System Diagram ........................................................ 4
System Description ................................................... 4 FRONT WIPER MOTOR GROUND CIRCUIT ... 21
Component Parts Location ........................................ 7 Diagnosis Procedure ...............................................21 I
Component Description ............................................ 7
WASHER SWITCH ............................................ 22
REAR WIPER AND WASHER SYSTEM ............ 8 Description ...............................................................22
System Diagram ........................................................ 8 Component Inspection .............................................22 J
System Description ................................................... 8
Component Parts Location ...................................... 10 REAR WIPER MOTOR CIRCUIT ...................... 24
Component Description .......................................... 10 Component Function Check ....................................24 K
Diagnosis Procedure ...............................................24
DIAGNOSIS SYSTEM (BCM) ............................11
REAR WIPER AUTO STOP SIGNAL CIRCUIT
COMMON ITEM ......................................................... 11 ... 26 WW
COMMON ITEM : CONSULT-III Function (BCM - Component Function Check ....................................26
COMMON ITEM) ..................................................... 11 Diagnosis Procedure ...............................................26
WIPER ....................................................................... 11 M
FRONT WIPER AND WASHER SYSTEM ........ 27
WIPER : CONSULT-III Function (BCM - WIPER).... 11 Wiring Diagram ........................................................27
DIAGNOSIS SYSTEM (IPDM E/R) .....................13 REAR WIPER AND WASHER SYSTEM .......... 32 N
Diagnosis Description ............................................. 13
Wiring Diagram ........................................................32
CONSULT - III Function (IPDM E/R) ....................... 13
ECU DIAGNOSIS ......................................... 39 O
COMPONENT DIAGNOSIS ......................... 14
BCM (BODY CONTROL MODULE) ................. 39
WIPER AND WASHER FUSE ............................14 Reference Value ......................................................39
Description .............................................................. 14 P
Diagnosis Procedure ............................................... 14 IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ................ 40
FRONT WIPER MOTOR LO CIRCUIT ...............15
Reference Value ......................................................40
Component Function Check .................................... 15
Fail Safe ..................................................................40
Diagnosis Procedure ............................................... 15
SYMPTOM DIAGNOSIS .............................. 42
WW-1
WIPER AND WASHER SYSTEM SYMPTOMS Precaution for Supplemental Restraint System
... 42 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
Symptom Table ...................................................... 42 SIONER" ................................................................. 48
WW-2
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001712140
B
DETAILED FLOW
1. LISTEN TO CUSTOMER COMPLAINT C
Listen to customer complaint. Get detailed information about the conditions and environment when the symp-
tom occurs.
D
>> GO TO 2
2. VERIFY THE SYMPTOM WITH OPERATIONAL CHECK E
Verify the symptom with operational check. Refer to WW-13, "Diagnosis Description".
>> GO TO 3 F
3. GO TO APPROPRIATE TROUBLE DIAGNOSIS
Go to appropriate trouble diagnosis. Refer to WW-42, "Symptom Table". G
>> GO TO 4
4. REPAIR OR REPLACE H
WW
WW-3
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
FRONT WIPER AND WASHER SYSTEM
System Diagram INFOID:0000000001712141
ALLIA0427GB
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION (LINKED WITH VEHICLE SPEED)
WW-4
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• BCM transmits the front wiper request signal (INT) to IPDM E/R with CAN communication according to the
front wiper INT operation condition and the intermittent operation delay interval judged value. A
Front wiper INT operating condition
- Ignition switch ON
- Front wiper switch INT B
WW
JPLIA0094GB
M
FRONT WIPER AUTO STOP OPERATION
• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.
• IPDM E/R detects the front wiper auto stop signal from the front wiper motor and detects the front wiper N
motor position (stop position/except stop position).
WW-5
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper
motor returns to the stop position.
JPLIA0095GB
NOTE:
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 3 times
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
• The front and rear washer motor is grounded through the combination switch with the front washer switch
ON.
FRONT WIPER DROP WIPE OPERATION
• BCM controls the front wiper to operate once according to the conditions of front wiper drop wipe operation.
Front wiper drop wipe operating condition
- Ignition switch ON
- Front wiper switch OFF
- Front washer switch OFF
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication so that the front
wiper operate once three seconds after front wiper operation linked with washer.
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER FAIL−SAFE OPERATION
• IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
WW-40, "Fail Safe".
WW-6
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Component Parts Location INFOID:0000000001712143
ALLIA0617ZZ
I
1. BCM M18, M20 (view with instru- 2. Front and rear washer motor E105 3. Washer fluid reservoir
ment lower panel LH removed)
4. Front wiper motor E23 (view with 5. IPDM E/R E121, E122, E124 6. Combination switch M28 J
cowl top removed)
Part Description
• Judges each switch status by the combination switch reading function. WW
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
• Controls the integrated relay according to the request (with CAN communication) from BCM. M
IPDM E/R
• Performs the auto stop control of the front wiper.
Combination switch
(Wiper and washer Refer to WW-4, "System Diagram".
N
switch)
Combination meter Transmits the vehicle speed signal to BCM with CAN communication.
WW-7
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
REAR WIPER AND WASHER SYSTEM
System Diagram INFOID:0000000001712145
ALLIA0271GB
OUTLINE
The rear wiper is controlled by each function of BCM.
Control by BCM
• Combination switch reading function
• Rear wiper control function
REAR WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM controls the rear wiper to start or stop.
REAR WIPER ON OPERATION
• BCM supplies power to the rear wiper motor according to the rear wiper ON operating condition.
Rear wiper ON operating condition
- Ignition switch ON
- Rear wiper switch ON
REAR WIPER INT OPERATION
• BCM supplies power to the rear wiper motor according to the INT operating condition.
Rear wiper INT operating condition
- Ignition switch ON
- Rear wiper switch INT
• BCM controls the rear wiper to operate once.
• BCM detects the rear wiper motor stopping position.
• BCM supplies power to the rear wiper motor after an intermittent from the stop of the rear wiper motor.
JPLIA0165GB
WW-8
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• BCM reads an auto stop signal from the rear wiper motor to detect a rear wiper motor position.
• When the rear wiper motor is at other than the stopping position, BCM continues to supply power to the rear A
wiper motor until it returns to the stopping position.
JPLIA0166GB
F
NOTE:
BCM stops supplying power to the rear wiper motor when the ignition switch is turned OFF.
REAR WIPER OPERATION LINKED WITH WASHER G
• BCM supplies power to the rear wiper motor according to the washer linked operating condition of rear
wiper. When the rear washer switch is turned OFF, BCM controls rear wiper to operate approximately three
times.
H
Washer linked operating condition of rear wiper
- Ignition switch ON
- Rear washer switch ON (0.4 second or more) I
• Front and rear washer motor becomes grounded through the combination switch when the rear washer
switch is turned ON.
REAR WIPER DROP WIPE OPERATION J
• BCM controls the rear wiper to operate once according to the rear wiper drop wipe operating condition.
Rear wiper drop wipe operating condition
- Ignition switch ON K
- Rear wiper switch OFF
- Rear washer switch OFF
• BCM controls the rear wiper so that it operates once time approximately three seconds later after the washer WW
interlocking operation of the rear wiper.
REAR WIPER FAIL−SAFE OPERATION
BCM performs the fail-safe function when the rear wiper auto stop circuit is malfunctioning. Refer to WW-40, M
"Fail Safe".
WW-9
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Component Parts Location INFOID:0000000001712147
ALLIA0618ZZ
1. BCM M18, M19, M20 (view with instru- 2. Front and rear washer motor con- 3. Washer fluid reservoir
ment lower panel LH removed) nector E105
4. Combination switch M28 5. Rear washer nozzle 6. Rear wiper motor D602
7. Glass hatch ajar switch D503
Part Description
• Judges each switch status by the combination switch reading function.
BCM • Supplies power to the rear wiper motor.
• Performs the auto stop control of the rear wiper.
Combination switch
Refer to WW-4, "System Diagram".
(Wiper and washer switch)
WW-10
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001712149
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
D
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to BCS-51, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification. F
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
I
— BCM ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × × J
Combination switch COMB SW ×
Glass hatch ajar switch TRUNK × ×
K
WIPER
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000001712150
WW
WORK SUPPORT
Setting
M
Service item Description
item
With vehicle speed
ON*
WIPER SPEED (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position) N
SETTING Without vehicle speed
OFF
(Front wiper intermittent time linked with the wiper intermittent dial position)
*:Factory setting O
DATA MONITOR
P
Monitor Item
Description
[Unit]
IGN ON SW Ignition switch ON status judged from ignition power supply.
IGN SW CAN Ignition switch ON status received from IPDM E/R with CAN communication.
WW-11
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Monitor Item
Description
[Unit]
FR WIPER HI
[OFF/ON]
FR WIPER LOW
[OFF/ON]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER INT
[OFF/ON]
FR WASHER SW
[OFF/ON]
INT VOLUME
Each switch status that BCM judges from the combination switch reading function.
[1 − 7]
FR WIPER STOP Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
[OFF/ON] tion.
VEHICLE SPEED The value of the vehicle speed signal received from combination meter with CAN com-
[km/h] munication.
RR WIPER ON
[OFF/ON]
RR WIPER INT
Each switch status that BCM judges from the combination switch reading function.
[OFF/ON]
RR WASHER SW
[OFF/ON]
RR WIPER STOP
Rear wiper motor (stop position) status input from the rear wiper motor.
[OFF/ON]
ACTIVE TEST
WW-12
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (IPDM E/R)
A
Diagnosis Description INFOID:0000000001712151
SELF DIAGNOSTIC G
Refer to PCS-28, "DTC Index".
DATA MONITOR
Monitor item H
ACTIVE TEST
Test item M
WW-13
WIPER AND WASHER FUSE
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
WIPER AND WASHER FUSE
Description INFOID:0000000001712154
Fuse list
Unit Location Fuse No. Capacity
Front wiper motor IPDM E/R 39 30 A
Front and rear washer motor Fuse block (J/B) 9 10 A
1. CHECK FUSES
Check that the following fuses are not blown.
WW-14
FRONT WIPER MOTOR LO CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR LO CIRCUIT
A
Component Function Check INFOID:0000000001712156
WW-15
FRONT WIPER MOTOR LO CIRCUIT
< COMPONENT DIAGNOSIS >
1. Turn the ignition switch ON.
2. Select "FRONT WIPER" of IPDM E/R active test item.
3. While operating the test item, check voltage between IPDM E/R
harness connector and ground.
Terminals
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER
Connector Terminal
Ground Battery WKIA3759E
LO
E121 32 voltage
OFF 0V
Is the measurement value normal?
YES >> GO TO 4
NO >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation of IPDM E/R".
4. CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R and front wiper motor.
3. Check continuity between IPDM E/R harness connector and
front wiper motor harness connector.
WW-16
FRONT WIPER MOTOR HI CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR HI CIRCUIT
A
Component Function Check INFOID:0000000001712158
WW-17
FRONT WIPER MOTOR HI CIRCUIT
< COMPONENT DIAGNOSIS >
1. Turn the ignition switch ON.
2. Select "FRONT WIPER" of IPDM E/R active test item.
3. While operating the test item, check voltage between IPDM E/R
harness connector and ground.
Terminals
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER
Connector Terminal
Ground Battery WKIA3760E
HI
E121 35 voltage
OFF 0V
Is the measurement value normal?
YES >> GO TO 4
NO >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation of IPDM E/R".
4. CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R and front wiper motor.
3. Check continuity between IPDM E/R harness connector and
front wiper motor harness connector.
WW-18
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
A
Component Function Check INFOID:0000000001712160
Terminals
(+) (-)
I
Voltage
IPDM E/R (Approx.)
IPDM E/R
Continuity N
Connector Terminal Ground
E122 43 No
Does continuity exist? O
WKIA1429E
YES >> Repair or replace harness.
NO >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation of IPDM E/R".
3. CHECK FRONT WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY P
WW-19
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
Check continuity between IPDM E/R harness connector and front
wiper motor harness connector.
WW-20
FRONT WIPER MOTOR GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR GROUND CIRCUIT
A
Diagnosis Procedure INFOID:0000000001712162
WW
WW-21
WASHER SWITCH
< COMPONENT DIAGNOSIS >
WASHER SWITCH
Description INFOID:0000000001712163
ALLIA0350GB
A: Terminal 14
B: Terminal 12
C: Terminal 13
D: Terminal 11
ALLIA0351ZZ
JPLIA0164GB
Combination switch
Condition Continuity
Terminal
11 12
Front washer switch ON Yes
13 14
Does continuity exist?
YES >> GO TO 2.
NO >> Replace combination switch. Refer to WW-49, "Removal and Installation".
2. CHECK REAR WASHER SWITCH
WW-22
WASHER SWITCH
< COMPONENT DIAGNOSIS >
1. Turn the ignition switch OFF.
2. Disconnect combination switch. A
3. Check continuity between the combination switch terminals.
A: Terminal 14
B
B: Terminal 12
C: Terminal 13
C
D: Terminal 11
ALLIA0352ZZ
JPLIA0164GB
D
Combination switch
Condition Continuity E
Terminal
11 14
Rear washer switch ON Yes
12 13 F
Does continuity exist?
YES >> Wiper and washer switch is normal.
NO >> Replace combination switch. Refer to WW-49, "Removal and Installation". G
WW
WW-23
REAR WIPER MOTOR CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
Component Function Check INFOID:0000000001712165
Terminals
Test item
(+) Voltage
BCM (−) (Approx.)
LKIA0551E
REAR WIPER
Connector Terminal
ON Battery voltage
M19 55 Ground
OFF 0V
Is the measurement value normal?
YES >> GO TO 2
NO >> GO TO 3
2. CHECK REAR WIPER MOTOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check continuity between rear wiper motor harness connector
and ground.
WW-24
REAR WIPER MOTOR CIRCUIT
< COMPONENT DIAGNOSIS >
3. Make sure hatch glass is closed
4. Check continuity between BCM harness connector and ground. A
BCM
Continuity
Connector Terminal Ground B
M19 42 No
Does continuity exist? C
YES >> GO TO 4.
NO >> Repair harness if shorted. If not, refer to SEC-44, "Diag-
WKIA1414E
nosis Procedure" (with Intelligent Key system) or SEC-
122, "Diagnosis Procedure" (without Intelligent Key system). D
BCM
Continuity
Connector Terminal Ground J
M19 55 No
Does continuity exist?
K
YES >> Repair or replace harness.
NO >> Replace BCM. Refer to BCS-54, "Removal and Installa-
tion".
ALLIA0650ZZ
WW
WW-25
REAR WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WIPER AUTO STOP SIGNAL CIRCUIT
Component Function Check INFOID:0000000001712167
BCM
Continuity
Connector Terminal Ground
M19 44 No
Is inspection result normal?
YES >> Replace BCM. Refer to BCS-54, "Removal and Installa-
tion".
ALLIA0651ZZ
NO >> Repair or replace harness.
WW-26
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
A
Wiring Diagram INFOID:0000000001712169
WW
P
ALLWA0039GB
WW-27
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
ALLIA0231GB
WW-28
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
ALLIA0232GB
WW-29
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
ALLIA0233GB
WW-30
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
ALLIA0234GB
WW-31
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
REAR WIPER AND WASHER SYSTEM
Wiring Diagram INFOID:0000000001712170
ALLWA0065GB
WW-32
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
ALLIA0235GB
WW-33
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
ALLIA0309GB
WW-34
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
ALLIA0310GB
WW-35
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
ALLIA0311GB
WW-36
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
ALLIA0312GB
WW-37
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
ALLIA0331GB
WW-38
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001712171
B
TERMINAL LAYOUT M
Refer to BCS-41, "Terminal Layout".
PHYSICAL VALUES N
Refer to BCS-41, "Physical Values".
WW-39
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference Value INFOID:0000000001712172
TERMINAL LAYOUT
Refer to PCS-19, "Terminal Layout".
PHYSICAL VALUES
Refer to PCS-19, "Physical Values".
Fail Safe INFOID:0000000001712173
Ignition switch Front wiper switch Front wiper auto stop signal
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not
ON
change for 10 seconds.
NOTE:
WW-40
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped. A
WW
WW-41
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table INFOID:0000000001712174
CAUTION:
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.
WW-42
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Probable malfunction location Inspection item
A
Combination switch
• Combination switch
Refer to BCS-53, "Symptom
• BCM
Table".
HI only Front wiper request signal B
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
IPDM E/R — C
Combination switch
• Combination switch
Refer to BCS-53, "Symptom
• BCM
Front wiper does not Table". D
stop. LO only Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
E
IPDM E/R —
Combination switch
• Combination switch
Refer to BCS-53, "Symptom
• BCM
Table".
F
INT only
Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ" G
• IPDM E/R
• Combination switch Combination switch
Intermittent adjustment • Harness between combination switch and BCM Refer to BCS-53, "Symptom
cannot be performed. • BCM Table". H
BCM —
Intermittent control
linked with vehicle Check the vehicle speed detection wiper setting. I
speed cannot be per- Refer to WW-11, "WIPER : CONSULT-III Function (BCM - WIPER)".
formed.
WW-43
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Probable malfunction location Inspection item
Rear wiper motor circuit
• Combination switch
ON only Refer to WW-24, "Compo-
• BCM
Rear wiper does not nent Function Check".
stop. Combination switch
• Combination switch
INT only Refer to BCS-53, "Symptom
• BCM
Table".
• Combination switch Combination switch
Wiper is not linked to • Harness between rear wiper motor and BCM Refer to BCS-53, "Symptom
the washer operation. • BCM Table".
BCM —
Rear wiper does not
Rear wiper does not return to the Stop posi-
operate normally. tion (Stops after a five- Rear wiper auto stop signal
second operation). • BCM
circuit
• Harness between rear wiper motor and BCM
Rear wiper stops after Refer to WW-26, "Compo-
• Rear wiper motor
operating for five sec- nent Function Check".
onds when ignition
switch is turned ON.
WW-44
NORMAL OPERATING CONDITION
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
A
Description INFOID:0000000001712175
WW
WW-45
FRONT WIPER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
Description INFOID:0000000001712176
The front wiper does not operate under any operation conditions.
Diagnosis Procedure INFOID:0000000001712177
WW-46
FRONT WIPER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
1. Turn the ignition switch ON.
2. Select "FRONT WIPER" of IPDM E/R active test item. A
3. With operating the test item, check voltage between IPDM E/R
harness connector and ground.
B
Terminals
Test item
(+) (−) Voltage
IPDM E/R FRONT WIP-
(Approx.) C
Connector Terminal ER
WKIA1427E
Battery
LO D
32 Ground voltage
OFF 0V
E121
Battery
HI E
35 voltage
OFF 0V
Is the measurement value normal? F
YES >> Replace front wiper motor. Refer to WW-49, "Removal and Installation".
NO >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation of IPDM E/R".
5. CHECK FRONT WIPER REQUEST SIGNAL INPUT G
CONSULT-III DATA MONITOR
1. Select "FR WIP REQ" of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO. H
3. With operating the front wiper switch, check the status of "FR WIP REQ".
Monitor I
Monitor item Condition
status
HI ON
Front wiper switch HI J
STOP OFF
FR WIP REQ
1LOW ON
Front wiper switch LO
STOP OFF K
Is the status of item normal?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation of IPDM E/R".
NO >> GO TO 6 WW
6. CHECK COMBINATION SWITCH
1. Perform the inspection of the combination switch. Refer to BCS-53, "Symptom Table".
M
Is combination switch normal?
YES >> Replace BCM. Refer to BCS-54, "Removal and Installation".
NO >> Repair or replace the applicable parts.
N
WW-47
PRECAUTION
< PRECAUTION >
PRECAUTION
PRECAUTION
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000001691120
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
WW-48
FRONT WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR A
FRONT WIPER AND WASHER SYSTEM
Removal and Installation INFOID:0000000001691134
B
H
SEL024J
WW-49
FRONT WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
WKIA4870E
1. Wiper arm covers 2. Wiper arm nuts 3. Front LH wiper arm and blade assembly
4. Wiper frame bolts 5. Wiper frame assembly 6. Wiper motor to frame nuts
7. Wiper motor spacer 8. Wiper motor 9. Front RH wiper arm and blade assembly
10. Wiper motor to frame bolts
Removal
1. Remove the cowl top. Refer to EXT-17, "Removal and Installation".
2. Remove wiper frame bolts, and remove wiper frame assembly.
LKIA0534E
WW-50
FRONT WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
WASHER HOSE LAYOUT
A
WKIA4139E F
G
WASHER NOZZLES
Removal
1. Remove the cowl top. Refer to EXT-17, "Removal and Installation". H
2. Remove washer nozzles.
Installation
I
Installation is in the reverse order of removal.
WKIA0071E
O
Installation
Installation is in the reverse order of removal.
P
WASHER FLUID RESERVOIR
Removal
1. Remove passenger front fender protector. Refer to. EXT-20, "Removal and Installation of Front Fender
Protector".
WW-51
FRONT WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
2. Remove clip, then remove washer fluid reservoir filler neck from
washer fluid reservoir.
LKIA0538E
LKIA0537E
LKIA0539E
Installation
Installation is in the reverse order of removal.
CAUTION:
After installation, add water up to the upper level of the washer fluid reservoir inlet and check for water
leaks.
WASHER MOTOR
Removal
1. Remove RH front fender protector. Refer to EXT-20, "Removal and Installation of Front Fender Protector".
2. Disconnect the front and rear washer hoses.
3. Disconnect the washer motor connectors.
WW-52
FRONT WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
4. Slide retaining ring upward to release front and rear washer
motor. A
LKIA0540E
D
5. Remove front and rear washer motor from washer fluid reservoir.
Installation
Installation is in the reverse order of removal. E
CAUTION:
When installing front and rear washer motor, there should be no packing twists, etc.
WASHER FLUID LEVEL SENSOR F
Removal
1. Remove washer fluid reservoir. Refer to "WASHER FLUID RESERVOIR". G
2. Lift level sensor out of washer fluid reservoir in the direction of
the arrow as shown.
H
J
LKIA0541E
Installation
Installation is in the reverse order of removal. K
WKIA3711E
O
WW-53
REAR WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
REAR WIPER AND WASHER SYSTEM
Removal and Installation INFOID:0000000001691148
LKIA0608E
Installation
1. Operate rear wiper motor one full cycle, then turn "OFF" (Auto Stop).
2. Clean pivot area as shown. This will reduce the possibility of
wiper arm looseness.
SEL024J
WW-54
REAR WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
WKIA4867E
H
1. Rear wiper motor cover 2. Rear wiper motor 3. Plate
4. Rear wiper motor cover base 5. Bracket 6. Grommet
7. Spacer 8. Washer 9. Rear wiper motor nut I
10. Pivot cap 11. Rear wiper arm and blade 12. Wiper arm nut
13. Wiper arm cover 14. Cap nut 15. Gasket
16. Gasket 17. Stud 18. Grommet J
19. Nut
Removal K
1. Remove wiper arm. Refer to WW-54, "Removal and Installation".
2. Remove pivot cap.
3. Remove rear wiper motor nut. WW
4. Remove rear wiper motor cover.
5. Disconnect rear wiper motor connector.
M
6. Remove nut and remove rear wiper motor.
LKIA0543E
P
7. Remove rear wiper motor cover base.
8. Remove bracket.
Installation
CAUTION:
• Do not drop the wiper motor or cause it to contact other parts.
Installation is in the reverse order of removal.
WW-55
REAR WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
REAR WASHER TUBE LAYOUT
WKIA4143E
1 Washer fluid reservoir 2 Washer fluid tube to rear door 3 Rear washer nozzle
4 Check valve
NOTE:
Connect the check valve (2) to the washer fluid tube (1) so that the
directional arrow on the check valve (2) points towards the washer
nozzle tube (3).
WKIA4242E
LKIA0545E
Installation
Installation is in the reverse order of removal.
NOTE:
Inspect rear washer nozzle for proper spray pattern, adjust as necessary. Refer to WW-57, "Rear Washer
Nozzle Adjustment".
WASHER FLUID RESERVOIR
Refer to WW-49.
WIPER AND WASHER SWITCH
WW-56
REAR WIPER AND WASHER SYSTEM
< ON-VEHICLE REPAIR >
Refer to EXL-116, "Removal and Installation".
A
WASHER MOTOR
Refer to WW-49.
Rear Washer Nozzle Adjustment INFOID:0000000001691149 B
LKIA0349E
WEL912A I
WW
WW-57