Defogger: Section
Defogger: Section
Defogger: Section
E
CONTENTS
BASIC INSPECTION .................................... 3 Diagnosis Procedure ...............................................14 F
Component Inspection .............................................15
DIAGNOSIS AND REPAIR WORKFLOW .......... 3
Work Flow ................................................................. 3 DRIVER SIDE DOOR MIRROR DEFOGGER ... 16
G
Description ...............................................................16
FUNCTION DIAGNOSIS ............................... 6 Component Function Check ....................................16
Diagnosis Procedure ...............................................16
REAR WINDOW DEFOGGER SYSTEM ............. 6 Component Inspection .............................................17 H
System Diagram ........................................................ 6
System Description ................................................... 6 PASSENGER SIDE DOOR MIRROR DEFOG-
Component Parts Location ........................................ 7 GER ................................................................... 18 I
Component Description ............................................. 7 Description ...............................................................18
Component Function Check ....................................18
DIAGNOSIS SYSTEM (BCM) ............................. 9 Diagnosis Procedure ...............................................18
J
COMMON ITEM ........................................................... 9 Component Inspection .............................................19
COMMON ITEM : CONSULT-III Function (BCM -
ECU DIAGNOSIS ......................................... 20
COMMON ITEM) ....................................................... 9
K
REAR WINDOW DEFOGGER ..................................... 9
BCM (BODY CONTROL MODULE) ................. 20
Reference Value ......................................................20
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) ...................... 9 Wiring Diagram ........................................................21
DEF
CAN COMMUNICATION ....................................10 SYMPTOM DIAGNOSIS .............................. 29
System Description ................................................. 10 REAR WINDOW DEFOGGER AND DOOR M
COMPONENT DIAGNOSIS ......................... 11 MIRROR DEFOGGER DO NOT OPERATE. .... 29
Diagnosis Procedure ...............................................29
REAR WINDOW DEFOGGER SWITCH ............11
REAR WINDOW DEFOGGER DOES NOT N
Description .............................................................. 11
Component Function Check .................................... 11 OPERATE BUT BOTH OF DOOR MIRROR
Diagnosis Procedure ............................................... 11 DEFOGGER OPERATE. ................................... 30
Diagnosis Procedure ...............................................30 O
REAR WINDOW DEFOGGER RELAY ..............12
Description .............................................................. 12 BOTH DOORS MIRROR DEFOGGER DON’T
Component Function Check .................................... 12 OPERATE BUT REAR WINDOW DEFOG-
P
Diagnosis Procedure ............................................... 12 GER OPERATES .............................................. 31
Component Inspection ............................................ 13 Diagnosis Procedure ...............................................31
REAR WINDOW DEFOGGER POWER SUP- DRIVER SIDE DOOR MIRROR DEFOGGER
PLY AND GROUND CIRCUIT ............................14 DOES NOT OPERATE. ..................................... 32
Description .............................................................. 14 Diagnosis Procedure ...............................................32
Component Function Check .................................... 14
DEF-1
PASSENGER SIDE DOOR MIRROR DEFOG- PRECAUTIONS ................................................. 35
GER DOES NOT OPERATE. ............................ 33 Supplemental Restraint System (SRS) "AIR BAG"
Diagnosis Procedure .............................................. 33 and "SEAT BELT PRE-TENSIONER" .................... 35
CONDENSER .................................................... 38
PRECAUTION ............................................. 35
Exploded View ........................................................ 38
Removal and Installation ......................................... 38
DEF-2
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001697540
B
OVERALL SEQUENCE
C
DEF
JMKIA0101GB
DETAILED FLOW
DEF-3
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
1. GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2
2. CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
- Record DTC and freeze frame data (Print them out with CONSULT-III.)
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3
Symptom is described, DTC is not displayed>>GO TO 4
Symptom is not described, DTC is displayed>>GO TO 5
3. CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5
4. CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6
5. PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
At this time, always connect CONSULT-III to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to XX-XX, "*****" and determine trouble diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirma-
tion Procedure.
Is DTC detected?
YES >> GO TO 8
NO >> Refer to XX-XX, "*****".
6. PERFORM BASIC INSPECTION
Perform DEF-3, "Work Flow".
Inspection End>>GO TO 7
7. DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to DEF-6, "System Description" based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 8
DEF-4
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
8. DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE A
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
B
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES >> GO TO 9
C
NO >> Check voltage of related BCM terminals using CONSULT-III.
9. REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part. D
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it. E
>> GO TO 10
10. FINAL CHECK F
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that G
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8 H
YES (Symptom remains)>>GO TO 6
NO >> INSPECTION END
I
DEF
DEF-5
REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
REAR WINDOW DEFOGGER SYSTEM
System Diagram INFOID:0000000001697541
ALLIA0183GB
Operation Description
• Turn rear window defogger switch ON when the ignition switch is turned ON. Then controller (auto amp.)
(rear window defogger switch) transmits rear window defogger switch signal to BCM.
• BCM turns rear window defogger relay ON when rear window defogger switch signal is received.
• Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and
operate when rear window defogger relay turns ON.
• BCM transmits rear window defogger control signal to IPDM E/R via CAN communication when rear window
defogger operates.
• Rear window defogger ON is displayed when controller (auto amp.) receives signals.
Timer function
• BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON while ignition switch is ON. It makes rear window defogger and door mirror defogger (with door
mirror defogger) operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same reaction also occurs during timer operation, if the ignition switch
is turned OFF.
DEF-6
REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
Component Parts Location INFOID:0000000001697543
ALLIA0619ZZ
DEF
1. BCM M18, M20 (view with glove box 2. Rear window defogger switch (part 3. A. Rear window defogger ground
removed) of front air control) connector D413 (Hatchback)
B. Rear window defogger connector
D412 (Hatchback) M
C. Condenser-1 D409, D411 (Hatch-
back)
4. A. Rear window defogger connector 5. IPDM E/R E46, E48 6. Door mirror LH D4, RH D107 (with
B140 (Sedan) heated mirrors)
N
B. Rear window defogger ground
connector B141 (Sedan)
C. Condenser-1 B130, B131 (Se- O
dan)
7. Heated mirror relay M48 (with heat-
ed mirrors)
P
Component Description INFOID:0000000001697544
• Operates the rear window defogger with the operation of rear window defogger switch.
BCM
• Performs the timer control of rear window defogger.
• Operates the rear window defogger and the door mirror defogger with the control signal from
Rear window defogger relay
BCM.
DEF-7
REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
Front air control (rear window • The rear window defogger switch is turned ON.
defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Rear window defogger
the rear window from fogging up.
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
Door mirror defogger* the door mirror from fogging up.
*: With door mirror defogger
DEF-8
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001697545
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
D
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to XX-XX, "*****".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
CONFIGURATION This function is not used even though it is displayed. F
SYSTEM APPLICATION
BCM can perform the following functions for each system. G
NOTE:
It can perform the diagnosis modes except the following for all subsystem selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
Rear window defogger REAR DEFOGGER × × I
BCM BCM ×
K
Data monitor
DEF-9
CAN COMMUNICATION
< FUNCTION DIAGNOSIS >
CAN COMMUNICATION
System Description INFOID:0000000001697547
DEF-10
REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS A
REAR WINDOW DEFOGGER SWITCH
Description INFOID:0000000001697548
B
• The rear window defogger is operated by turning the rear window defogger switch ON.
• Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
C
Component Function Check INFOID:0000000001697549
Terminals J
(+) Condition of rear
Voltage (V)
window defogger
Controller (auto (–) (Approx.)
switch K
amp.) connec- Terminal
tor
ON Battery voltage ALLIA0174ZZ
M37 22 Ground DEF
OFF 0
Is the inspection result normal?
YES >> Repair or replace harness. M
NO >> Replace controller (auto amp.). Refer to XX-XX, "*****".
DEF-11
REAR WINDOW DEFOGGER RELAY
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER RELAY
Description INFOID:0000000001697551
Terminals
Condition of rear
Voltage (V)
(+) window defogger
(–) (Approx.)
switch
BCM connector Terminal
ON 0
M18 59 Ground
OFF Battery voltage
Is the inspection result normal? ALLIA0175ZZ
Terminal
Rear window Condition Continuity
D
defogger relay
12V direct current supply between termi-
Yes
3 5 nals 1 and 2.
E
No current supply No
Is the inspection result normal?
SEF497Y
YES >> Inspection End. F
NO >> Replace rear window defogger relay.
DEF
DEF-13
REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
Description INFOID:0000000001697555
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
Component Function Check INFOID:0000000001697556
Terminals
(+) Condition of rear
Voltage (V)
window
Rear window (–) (Approx.)
defogger switch
defogger Terminal
connector
ON Battery voltage ALLIA0177ZZ
B53 1 Ground
OFF 0
Is the inspection result normal?
YES >> GO TO 2
NO >> GO TO 3
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger.
3. Check continuity between rear window defogger connector and
ground.
DEF-14
REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect condenser and rear window defogger. A
3. Check continuity between condenser connector (A) and rear
window defogger connector (B).
B
Condenser Rear window defogger
Terminal Terminal Continuity
connector connector
B52 (A) 1 B53 (B) 1 Yes C
Is the inspection result normal?
YES >> GO TO 4 ALLIA0179ZZ
1. CHECK FILAMENT
Check the filament for damage or open circuits. O
Refer to DEF-36, "Inspection and Repair".
Is the inspection result normal?
YES >> Inspection End. P
NO >> Repair filament. Refer to DEF-36, "Inspection and Repair".
DEF-15
DRIVER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
DRIVER SIDE DOOR MIRROR DEFOGGER
Description INFOID:0000000001697559
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
Component Function Check INFOID:0000000001697560
Terminals
Condition of
(+) rear window Voltage (V)
(–) defogger (Approx.)
Door mirror LH
Terminal switch
connector
ON Battery voltage ALLIA0181ZZ
D4 1 Ground
OFF 0
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror LH connector and ground.
ALLIA0184ZZ
DEF-16
DRIVER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
Refer to XX-XX, "*****".
Is the inspection result normal? A
YES >> Check the following.
• Battery power supply circuit.
• Fuse block (J/B). B
NO >> Repair or replace the malfunctioning parts.
Component Inspection INFOID:0000000001697562
C
1. CHECK DOOR MIRROR DEFOGGER LH
1. Turn ignition switch OFF.
D
2. Disconnect door mirror LH.
3. Check continuity between door mirror terminals.
E
Terminal Continuity
1 2 Yes
Is the inspection result normal? F
YES >> Inspection End.
NO >> Replace door mirror LH. Refer to XX-XX, "*****".
ALLIA0185ZZ
G
DEF
DEF-17
PASSENGER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
PASSENGER SIDE DOOR MIRROR DEFOGGER
Description INFOID:0000000001697563
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
Component Function Check INFOID:0000000001697564
Terminals
Condition of rear
(+) Voltage (V)
window defogger
(–) (Approx.)
Door mirror RH switch
Terminal
connector
ON Battery voltage ALLIA0181ZZ
D107 1 Ground
OFF 0
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror RH connector and
ground.
DEF-18
PASSENGER SIDE DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
Refer to XX-XX, "*****".
Is the inspection result normal? A
YES >> Check the following.
• Battery power supply circuit.
• Fuse block (J/B). B
NO >> Repair or replace the malfunctioning parts.
Component Inspection INFOID:0000000001697566
C
1. CHECK DOOR MIRROR DEFOGGER RH
1. Turn ignition switch OFF.
D
2. Disconnect door mirror RH.
3. Check continuity between door mirror terminals.
Terminal Continuity E
1 2 Yes
Is the inspection result normal?
F
YES >> Inspection End.
NO >> Replace door mirror RH. Refer to XX-XX, "*****".
ALLIA0185ZZ
G
DEF
DEF-19
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001697567
TERMINAL LAYOUT
Refer to XX-XX, "*****".
PHYSICAL VALUES
Refer to XX-XX, "*****".
DEF-20
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram INFOID:0000000001697568
DEF
ALLWA0121GB
P
DEF-21
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ALLIA0659GB
DEF-22
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DEF
ALLIA0660GB
DEF-23
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ALLIA0661GB
DEF-24
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DEF
ALLIA0662GB
DEF-25
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ALLIA0663GB
DEF-26
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DEF
ALLIA0664GB
DEF-27
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ALLIA0665GB
DEF-28
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPER-
ATE.
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT
OPERATE.
B
Diagnosis Procedure INFOID:0000000001697569
DEF
DEF-29
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIR-
ROR DEFOGGER OPERATE.
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR
MIRROR DEFOGGER OPERATE.
Diagnosis Procedure INFOID:0000000001697570
DEF-30
BOTH DOORS MIRROR DEFOGGER DON’T OPERATE BUT REAR WINDOW
DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >
BOTH DOORS MIRROR DEFOGGER DON’T OPERATE BUT REAR WIN-
A
DOW DEFOGGER OPERATES
Diagnosis Procedure INFOID:0000000001697571
B
1. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
C
Refer to XX-XX, "*****".
Is the inspection result normal?
YES >> Check the following. D
• Battery power supply circuit.
• Fuse block (J/B).
NO >> Repair or replace the malfunctioning parts.
E
DEF
DEF-31
DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
< SYMPTOM DIAGNOSIS >
DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
Diagnosis Procedure INFOID:0000000001697572
DEF-32
PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
< SYMPTOM DIAGNOSIS >
PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
A
Diagnosis Procedure INFOID:0000000001697573
DEF
DEF-33
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WIN-
DOW DEFOGGER OPERATES
Diagnosis Procedure INFOID:0000000001697574
DEF-34
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION- B
ER" INFOID:0000000001697575
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H
DEF
DEF-35
FILAMENT
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR
FILAMENT
Inspection and Repair INFOID:0000000001697576
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
SEL122R
SEL263
SEL265
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)
DEF-36
FILAMENT
< ON-VEHICLE REPAIR >
• Ruler 30 cm (11.8 in) long
• Drawing pen A
• Heat gun
• Alcohol
• Cloth
B
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol. C
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use. D
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
E
PIIA0215E
F
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited. G
Do not touch repaired area while test is being conducted.
I
SEL012D
M
SEL013D
DEF-37
CONDENSER
< ON-VEHICLE REPAIR >
CONDENSER
Exploded View INFOID:0000000001697577
REMOVAL
1. Remove the rear seat cushion and the rear seat back.
Refer to XX-XX, "*****".
2. Remove the rear kickplate, rear wheel well garnish and the rear pillar finisher.
Refer to XX-XX, "*****".
3. Remove bolt (A), and then remove condenser (1) from the vehi-
cle body.
JMLIA0013ZZ
INSTALLATION
Install in the reverse order of removal.
DEF-38