Defogger: Section

DRIVER CONTROLS
SECTION DEF DEFOGGER

B
E
CONTENTS
BASIC INSPECTION .................................... 3 REAR WINDOW DEFOGGER RELAY ............. 17 F
Description ...............................................................17
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 Component Function Check ....................................17
Work Flow ................................................................. 3 Diagnosis Procedure ...............................................17 G
FUNCTION DIAGNOSIS ............................... 4 REAR WINDOW DEFOGGER .......................... 18
Description ...............................................................18
REAR WINDOW DEFOGGER SYSTEM ............. 4 Component Function Check ....................................18 H
System Diagram ........................................................ 4 Diagnosis Procedure ...............................................18
System Description ................................................... 4 Component Inspection .............................................19
Component Parts Location ........................................ 5 I
Component Description ............................................. 5 DOOR MIRROR DEFOGGER ........................... 20
DIAGNOSIS SYSTEM (BCM) ............................. 6 DRIVER SIDE .............................................................20
DRIVER SIDE : Description .....................................20 J
COMMON ITEM ........................................................... 6 DRIVER SIDE : Component Function Check ..........20
COMMON ITEM : CONSULT-III Function (BCM - DRIVER SIDE : Diagnosis Procedure .....................20
COMMON ITEM) ....................................................... 6 DRIVER SIDE : Component Inspection ...................21 K
REAR WINDOW DEFOGGER ..................................... 6 PASSENGER SIDE ....................................................21
REAR WINDOW DEFOGGER : CONSULT-III PASSENGER SIDE : Description ............................21
Function (BCM - REAR DEFOGGER) ...................... 6 PASSENGER SIDE : Component Function Check DEF
DIAGNOSIS SYSTEM (IPDM E/R) ...................... 8 ....21
PASSENGER SIDE : Diagnosis Procedure ............22
Diagnosis Description ............................................... 8
PASSENGER SIDE : Component Inspection ..........23 M
CONSULT - III Function (IPDM E/R) ....................... 10
REAR WINDOW DEFOGGER ON SIGNAL ..... 24
COMPONENT DIAGNOSIS ......................... 13
WITH AUTO A/C ........................................................24 N
REAR WINDOW DEFOGGER SWITCH ............13 WITH AUTO A/C : Description ................................24
WITH AUTO A/C ........................................................ 13 WITH AUTO A/C : Component Function Check ......24
WITH AUTO A/C : Description ................................ 13 WITH AUTO A/C : Diagnosis Procedure .................24 O
WITH AUTO A/C : Component Function Check .... 13
WITHOUT AUTO A/C ................................................24
WITH AUTO A/C : Diagnosis Procedure ................. 13 WITHOUT AUTO A/C : Description .........................25
WITHOUT AUTO A/C ................................................ 14 WITHOUT AUTO A/C : Component Function P
WITHOUT AUTO A/C : Description ........................ 14 Check ......................................................................25
WITHOUT AUTO A/C : Component Function WITHOUT AUTO A/C : Diagnosis Procedure .........25
Check ...................................................................... 15
WITHOUT AUTO A/C : Diagnosis Procedure ......... 15
ECU DIAGNOSIS ......................................... 26
WITHOUT AUTO A/C : Component Inspection ...... 16 BCM (BODY CONTROL MODULE) ................. 26
Reference Value ......................................................26
DEF-1
Wiring Diagram - DEFOGGER CONTROL SYS- REAR WINDOW DEFOGGER DOES NOT
TEM (LHD MODELS) - ........................................... 42 OPERATE BUT BOTH OF DOOR MIRROR
Wiring Diagram - DEFOGGER CONTROL SYS- DEFOGGER OPERATE. ................................... 70
TEM (RHD MODELS) - .......................................... 46 Diagnosis Procedure ............................................... 70
Fail Safe ................................................................. 49
DTC Inspection Priority Chart .............................. 51 DOOR MIRROR DEFOGGER DOES NOT OP-
DTC Index .............................................................. 51 ERATE ............................................................... 71
IPDM E/R (INTELLIGENT POWER DISTRI- BOTH SIDE ............................................................... 71
BUTION MODULE ENGINE ROOM) ................. 52 BOTH SIDE : Diagnosis Procedure ........................ 71
Reference Value ..................................................... 52
DRIVER SIDE ............................................................ 71
Wiring Diagram - DEFOGGER CONTROL SYS-
DRIVER SIDE : Diagnosis Procedure ..................... 71
TEM (LHD MODELS) - ........................................... 58
Wiring Diagram - DEFOGGER CONTROL SYS- PASSENGER SIDE ................................................... 71
TEM (RHD MODELS) - .......................................... 62 PASSENGER SIDE : Diagnosis Procedure ............ 71
Fail Safe ................................................................. 65
DTC Index .............................................................. 67 REAR WINDOW DEFOGGER INDICATOR ...... 72
Diagnosis Procedure ............................................... 72
SYMPTOM DIAGNOSIS ............................. 68
PRECAUTION ............................................ 73
REAR WINDOW DEFOGGER DOES NOT
OPERATE .......................................................... 68 PRECAUTIONS ................................................. 73
Diagnosis Procedure .............................................. 68 Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
REAR WINDOW DEFOGGER AND DOOR SIONER" ................................................................. 73
MIRROR DEFOGGER DO NOT OPERATE. ..... 69
Diagnosis Procedure .............................................. 69 ON-VEHICLE REPAIR ............................... 74
FILAMENT ......................................................... 74
Inspection and Repair ............................................. 74
DEF-2
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001189045
B
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM C
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
D
>> GO TO 2.
2.CHECK DTC E
Perform self diagnosis with CONSULT-III
Is any DTC detected?
YES >> Refer to BCS-62, "DTC Index". F
NO >> GO TO 3.
3.REPRODUCE THE MALFUNCTION INFORMATION G
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
H
>> GO TO 4.
4.IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
I
Use “Symptom diagnosis” from the symptom inspection result in step 3. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.
J
>> GO TO 5.
5.IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system. K
>> GO TO 6.
DEF
6.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
M
>> GO TO 7.
7.FINAL CHECK
N
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 3.
Are all malfunctions corrected?
O
YES >> INSPECTION END
NO >> GO TO 4.
P
DEF-3
REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
System Diagram INFOID:0000000001189046
JMLIA0030GB
System Description INFOID:0000000001189047
OPERATION DESCRIPTION
• BCM detects that the rear window defogger switch is turned ON when the ignition switch is ON, and then
transmits the rear window defogger switch signal to IPDM E/R via CAN communication for approximately 15
minutes.
• IPDM E/R turns rear window defogger relay ON when it receives the rear window defogger switch signal.
Then, it transmits the rear window defogger ON signal to ECM via CAN communication.
• The power is supplied to the rear window defogger and door mirror defogger (with mirror defogger) when the
rear window defogger relay is turned ON.
TIMER FUNCTION
• BCM transmits the rear window defogger switch signal to IPDM E/R for approximately 15 minutes when the
rear window defogger switch is turned ON with the ignition switch ON. Then, IPDM E/R operates the rear
window defogger and door mirror defogger (with mirror defogger).
• The timer is cancelled if the rear window defogger switch is pressed again during timer operation. BCM
stops the output of rear window defogger switch signal. The same reaction also occurs during timer opera-
tion if the ignition switch is turned OFF.
INPUT/OUTPUT SIGNAL CHART
Switch Input signal to BCM BCM function Acutuator

Rear window defogger switch Defogger switch signal Rear window defogger & Door mir- Rear window defogger
Ignition switch Ignition signal ror defogger* control Door mirror defogger *
*: With mirror defogger
DEF-4
Component Parts Location INFOID:0000000001189048
JMLIA0031ZZ
I
Rear window defogger switch (built
1. BCM M65,M66,M67 2. IPDM E/R E10,E12,E14 3.
in AUTO AMP. M53)
Rear window defogger switch (built in
4. 5. Rear window defogger B58 6. Rear window defogger D155 J
heater control panel M54)
A. Behind glove box B. Engine room dash panel (LH) C. Behind back door trim finisher
Component Description INFOID:0000000001189049 K
• Rear window defogger switch operation is transmitted IPDM E/R via CAN communi-
DEF
BCM cation.
• Performs the timer control of rear window defogger.
Rear window defogger relay • Operates the rear window defogger and the door mirror defogger* with the control sig-
M
nal from IPDM E/R.
• BCM controls rear window defogger relay via CAN communication, and then oper-
IPDM E/R
ates rear window defogger or door mirror defogger.
N
Auto amp. / Heater control panel • The rear window defogger switch is installed.
(Rear window defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to
Rear window defogger O
prevent the rear window from fogging up.
• Heats the heating wire with the power supply from the rear window defogger relay to
Door mirror defogger* prevent the door mirror from fogging up.
*With mirror defogger
P
DEF-5
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001555106
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description

Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM. Refer to BCS-62, "DTC Index".
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Enables to read and save the vehicle specification.
Configuration
• Enables to write the vehicle specification when replacing BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Intelligent Key system INTELLIGENT KEY ×
Combination switch COMB SW ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door open TRUNK × ×
Vehicle security system THEFT ALM × × ×
Signal buffer system SIGNAL BUFFER × ×
PTC heater system PTC HEATER × ×
REAR WINDOW DEFOGGER

REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000001189051
Data monitor
DEF-6
Monitor Item Description A

REAR DEF SW Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
B
ACTIVE TEST
C
Test Item Description
REAR DEFOGGER Give a drive signal to the rear window defogger relay to activate it.
D
DEF
DEF-7
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description INFOID:0000000001555128
Auto active test

Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Rear window defogger
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan (LO, HI)
Operation procedure
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4. Turn the ignition switch ON within 10 seconds. Then the horn sounds once and the auto active test starts.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn ignition switch OFF.
CAUTION:
• If auto active test mode cannot be actuated, check door switch system.
• Never start the engine.
Inspection in auto active test mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.
JPMIA0234ZZ
DEF-8
Operation A
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test.
2 Rear window defogger 10 seconds B
3 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• License plate lamps C
4 10 seconds
• Tail lamps
• Front fog lamps
5 Headlamps LO ⇔ HI 5 times D
6 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
7 Cooling fan LO for 5 seconds → HI for 5 seconds
E
Concept of auto active test
JPMIA0235GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto K
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode DEF
Symptom Inspection contents Possible cause

M
YES BCM signal input circuit
Perform auto active test. • Rear window defogger

Rear window defogger does not operate Does the rear window defog- • Rear window defogger ground circuit
ger operate? NO • Harness or connector between IPDM N
E/R and rear window defogger
• IPDM E/R
Any of the following components do not operate YES BCM signal input circuit O
• Parking lamps
• License plate lamps Perform auto active test. • Lamp or motor
• Tail lamps Does the applicable system • Lamp or motor ground circuit
• Front fog lamps operate? NO • Harness or connector between IPDM P
• Headlamp (HI, LO) E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R
DEF-9
Symptom Inspection contents Possible cause
• Communication signal between BCM
and auto amp. (with auto A/C)
• Communication signal between BCM
and heater control panel (without auto
A/C, with manual A/C)
YES
• BCM
Perform auto active test. • CAN communication signal between
A/C compressor does not operate Does the magnet clutch oper- BCM and ECM
ate? • CAN communication signal between
ECM and IPDM E/R
• Magnet clutch
• Harness or connector between IPDM
NO
E/R and magnet clutch
• IPDM E/R
E/R and oil pressure switch
YES
• Oil pressure switch
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal between
lamp blink? IPDM E/R and BCM
NO • CAN communication signal between
BCM and combination meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal between
ECM and IPDM E/R
• Cooling fan
• Cooling fan ground circuit
Perform auto active test. • Harness or connector between IPDM
Cooling fan does not operate E/R and cooling fan
Does the cooling fan operate?
• IPDM E/R
NO
• Cooling fan relay-3*
E/R and cooling fan relay-3*
• Harness or connector between cooling
fan and cooling fan relay-3*
NOTE:
*: MR engine and K9K engine models
CONSULT - III Function (IPDM E/R) INFOID:0000000001555129
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
Diagnosis mode Description

Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
SELF DIAGNOSTIC
Refer to PCS-31, "DTC Index".
DATA MONITOR
Monitor item
DEF-10
Monitor Item MAIN A

Description
[Unit] SIGNALS
MOTOR FAN REQ Displays the value of the cooling fan speed signal received from ECM via CAN commu-
×
[1 - 4] nication.
B
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via CAN
×
[Off/On] communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN com- C
×
[Off/On] munication.
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN commu-
×
[Off/On] nication.
D
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN com-
×
FR FOG REQ Displays the status of the front fog light request signal received from BCM via CAN com-
× E
HL WASHER REQ Displays the status of the headlamp washer request signal received from BCM via CAN
F
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN com-
×
[Stop/1LOW/Low/Hi] munication.
WIP AUTO STOP
× Displays the status of the front wiper auto stop signal judged by IPDM E/R. G
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
H
ST RLY REQ Displays the status of the ignition and starter request signal received from BCM via CAN
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R. I
[Off/On]
RR DEF REQ Displays the status of the rear defogger request signal received from BCM via CAN com-
×
OIL P SW
J
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
REV SW
Displays the status of the reverse switch judged by IPDM E/R.
[Off/On] K
Displays the status of the hood switch judged by IPDM E/R.
HOOD SW
NOTE:
[Off/On]
This item is monitored only the vehicle with the Vehicle Security (Theft Warning) system. DEF
Displays the status of the theft warning horn request signal received from BCM via CAN
THFT HRN REQ communication.
[Off/On] NOTE:
M
This item is monitored only the vehicle with the Vehicle Security (Theft Warning) system.
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored.
N
IGN ON SW
Displays the status of the ignition switch judged by IPDM E/R.
[Off/On]
ACTIVE TEST O
Test item
Test item Operation Description P

Off OFF
REAR DEFOGGER
On Operates the rear window defogger relay.
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
DEF-11
Test item Operation Description
1 OFF
2 Operates the cooling fan relay (low operation).
MOTOR FAN
3
Operates the cooling fan relay (high operation).
4
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
Hi
ond intervals.
Fog Operates the front fog lamp relay.
HORN On Operates horn relay for 20 ms.
DEF-12
REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS A
WITH AUTO A/C
B
WITH AUTO A/C : Description INFOID:0000000001189054
The rear window defogger is operated by turning the rear window defogger switch ON. C
WITH AUTO A/C : Component Function Check INFOID:0000000001189055
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION D

Check (“REAR DEF SW”, “IGN ON SW”) in DATA MONITOR mode with CONSULT-III. Refer to DEF-6, "REAR
WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)".
E
When rear window defogger switch is turned to ON
REAR DEF SW :ON
F
OK or NG
OK >> Rear window defogger switch is OK.
NG >> Refer to DEF-13, "WITH AUTO A/C : Diagnosis Procedure".
G
WITH AUTO A/C : Diagnosis Procedure INFOID:0000000001189056
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION H

1. Turn ignition switch ON.
2. Check voltage between BCM harness connector and ground.
I
BCM Voltage (V)
Ground Condition
Connector Terminal (Approx.)
Rear window defogger switch is pressed. 0

J
K
M65 21 Ground
Rear window defogger switch is OFF.
DEF
JPMIA0154GB
Is the inspection result normal? M

YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT N
2. Disconnect BCM connector and auto amp. connector.
3. Check continuity between BCM harness connector and auto amp. harness connector. O
BCM Auto amp.

Continuity
Connector Terminal Connector Terminal P
M65 21 M53 23 Yes
4. Check continuity between BCM harness connector and ground.
DEF-13
BCM
Ground Continuity
Connector Terminal
M65 21 Ground No
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and auto amp.
3.CHECK REAR WINDOW DEFOGGER SWITCH GROUND CIRCUIT
1. Check continuity between auto amp. harness connector and ground.
Auto amp.
Ground Continuity
Connector Terminal
M53 17 Ground Existed
YES >> GO TO 4.
NO >> Repair or replace harness between auto amp. and ground.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
BCM Voltage (V)

Ground
M65 21 Ground
JPMIA0154GB

YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK IINTERMITTENT INCDENT
Check intermittent incident.
Refer to GI-39, "Intermittent Incident".
YES >> Replace auto amp. Refer toVTL-22, "Removal and Installation"
NO >> Repair or replace the malfunctioning parts.
>> INSPECTION END

WITHOUT AUTO A/C
WITHOUT AUTO A/C : Description INFOID:0000000001189057
The rear window defogger is operated by turning the rear window defogger switch ON.
DEF-14
WITHOUT AUTO A/C : Component Function Check INFOID:0000000001189058
A
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION
WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)". B

REAR DEF SW :ON C
OK or NG
OK >> Rear window defogger switch is OK. D
NG >> Refer to DEF-15, "WITHOUT AUTO A/C : Diagnosis Procedure".
WITHOUT AUTO A/C : Diagnosis Procedure INFOID:0000000001189059
E
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION
2. Check voltage between BCM harness connector and ground. F
BCM Voltage (V)

Ground Condition
Connector Terminal (Approx.) G
Rear window defogger switch is pressed. 0
M65 21 Ground
Rear window defogger switch is OFF.
I
JPMIA0154GB
J
YES >> GO TO 6.
NO >> GO TO 2. K
2.CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT
2. Disconnect BCM connector and heater control panel connector. DEF
3. Check continuity between BCM harness connector and heater control panel harness connector.
BCM Heater control panel M

Continuity
Connector Terminal Connector Terminal
M65 21 M54 18 Yes
N
4. Check continuity between BCM harness connector and ground
BCM
Ground Continuity O
Connector Terminal
M65 21 Ground No
Is the inspection result normal? P
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and heater control panel.
3.CHECK REAR WINDOW DEFOGGER SWITCH GROUND CIRCUIT
1. Check continuity between heater control panel harness connector and ground.
DEF-15
Heater control panel

Ground Continuity
Connector Terminal
M54 20 Ground Existed
YES >> GO TO 4.
NO >> Repair or replace harness between heater control panel and ground.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
BCM Voltage (V)

Ground
M65 21 Ground
JPMIA0154GB

YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK REAR WINDOW DEFOGGER SWITCH
Check rear window defogger switch.
Refer to DEF-16, "WITHOUT AUTO A/C : Component Inspection".
YES >> GO TO 6.
NO >> Replace heater control panel (rear window defogger switch). Refer to VTL-81, "Removal and
Installation".
6.CHECK INTERMITTENT INCDENT
>> INSPECTION END.

WITHOUT AUTO A/C : Component Inspection INFOID:0000000001189060
1.CHECK HEATER CONTROL PANEL (REAR WINDOW DEFOGGER SWITCH)

Check heater control panel (rear window defogger switch connector).
Heater control panel

Condition Continuity
Connector Terminal
Rear window defogger switch is pressed Existed
M54 18 20
Rear window defogger switch: OFF Not existed
YES >> INSPECTION END.
NO >> Replace heater control panel (rear window defogger switch). Refer to VTL-81, "Removal and
Installation".
DEF-16
REAR WINDOW DEFOGGER RELAY
REAR WINDOW DEFOGGER RELAY
A
Description INFOID:0000000001524229
The rear window defogger is operated by turning the rear window defogger switch ON. B
Component Function Check INFOID:0000000001524230
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION C

WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)".
D
REAR DEF SW :ON
E
OK or NG
OK >> Rear window defogger switch is OK.
NG >> Refer to DEF-17, "Diagnosis Procedure".
F
Diagnosis Procedure INFOID:0000000001524231
1.CHECK FUSE G
2. Check the following.
- 15A fuse (No. 41, located in IPDM E/R) H
- 15A fuse (No. 42, located in IPDM E/R)
YES >> GO TO 2. I
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK IPDM E/R OUTPUT SIGNAL
J
2. Check voltage between IPDM E/R harness connector and ground.
IPDM E/R K
Voltage (V)
Ground Condition of rear window defogger switch
ON Battery voltage
E14 49 Ground DEF
OFF 0
YES >> GO TO 3. M
NO >> Replace IPDM E/R. Refer toPCS-33, "Removal and Installation"
3.CHECK INTERMITTENT INCIDENT
N
Refer to GI-39, "Intermittent Incident"
>> INSPECTION END O
DEF-17
Description INFOID:0000000001524232
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
Component Function Check INFOID:0000000001524233
1.CHECK REAR WINDOW DEFOGGER

Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch
ON.
YES >> Rear window defogger is OK.
NO >> Refer to DEF-18, "Diagnosis Procedure".
1.CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT

2. Check voltage between rear window defogger harness connector and ground.
Rear window defogger Condition of rear window Voltage (V)

Ground
Connector Terminal defogger switch (Approx.)
ON Battery voltage
B58 1 Ground
OFF 0
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK REAR WINDOW DEFOGGER GROUND CIRCUIT
2. Disconnect rear window defogger connector.
3. Check continuity between rear window defogger harness connector and ground.
Rear window defogger

Ground Continuity
Connector Terminal
D155 2 Ground Existed
YES >> GO TO 3.
NO >> Repair or replace harness between rear window defogger and ground.
3.CHECK FILAMENT
Check filament.
Refer to DEF-19, "Component Inspection".
YES >> GO TO 5.
NO >> Repair filament.
4.CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT
2. Disconnect IPDM E/R connector and rear window defogger connector.
3. Check continuity between IPDM E/R harness connector and rear window defogger harness connector.
DEF-18
IPDM E/R Rear window defogger A

Continuity
E14 49 B58 1 Existed
B
4. Check continuity between IPDM E/R harness connector and ground.
IPDM E/R
Ground Continuity C
Connector Terminal
E14 49 Ground Not existed
Is the inspection result normal? D
YES >> GO TO 5.
NO >> Repair or replace harness between IPDM E/R and rear window defogger.
5.CHECK INTERMITTENT INCIDENT E
F
>> INSPECTION END
Component Inspection INFOID:0000000001524235
G
1.CHECK FILAMENT
Check the filament for damage or blown.
Refer to DEF-74, "Inspection and Repair". H
NO >> Repair filament. I
DEF
DEF-19
DOOR MIRROR DEFOGGER
DRIVER SIDE
DRIVER SIDE : Description INFOID:0000000001524236
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
DRIVER SIDE : Component Function Check INFOID:0000000001524237
1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check that heating wire of driver side door mirror defogger is heated when turning the rear window defogger
switch ON.
YES >> Driver side door mirror defogger is OK.
NO >> Refer to DEF-20, "DRIVER SIDE : Diagnosis Procedure".
DRIVER SIDE : Diagnosis Procedure INFOID:0000000001524238
1.CHECK FUSE
2. Check 10A fuse (No. 6, located in fuse and fusible link box).
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if fuse is blown.
2.CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
2. Check voltage between door mirror (driver side) harness connector and ground.
Door mirror (driver side) Condition of rear win- Voltage (V)

Ground
Connector Terminal dow defogger switch (Approx.)
LHD D3 ON Battery voltage

7 Ground
RHD D23 OFF 0
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
2. Disconnect door mirror (driver side) connector.
3. Check continuity between door mirror (driver side) harness connector and ground.
Door mirror (driver side)

Ground Continuity
Connector Terminal
LHD D3
8 Ground Existed
RHD D23
YES >> GO TO 4.
NO >> Repair or replace harness between door mirror (driver side) and ground.
Check driver side door mirror defogger.
Refer to DEF-21, "DRIVER SIDE : Component Inspection".
DEF-20
YES >> GO TO 6.
NO >> Replace door mirror glass (driver side). Refer to MIR-20, "Removal and Installation". A
5.CHECK DOOR MIRROR CIRCUIT
B
2. Disconnect IPDM E/R connector and door mirror (driver side) connector.
3. Check continuity between door mirror (driver side) harness connector and IPDM E/R harness connector.
Door mirror (driver side) IPDM E/R C

Continuity
LHD D3
7 E14 49 Existed D
RHD D23
4. Check continuity between door mirror (driver side) harness connector and ground.
E
Door mirror (driver side)
Ground Continuity
Connector Terminal
LHD D3 F
7 Ground Not existed
RHD D23
G
YES >> GO TO 6.
NO >> Repair or replace harness between door mirror (driver side) and IPDM E/R.
6.CHECK INTERMITTENT H
>> INSPECTION END I
DRIVER SIDE : Component Inspection INFOID:0000000001524239
J
2. Disconnect door mirror (driver side) connector. K
3. Check continuity between door mirror connector.
Door mirror (diver side)

Continuity DEF
Connector Terminal
LHD D3
7 8 Existed
RHD D23 M
NO >> Replace door mirror glass (driver side). Refer to MIR-20, "Removal and Installation". N
PASSENGER SIDE
PASSENGER SIDE : Description INFOID:0000000001524240 O
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
P
PASSENGER SIDE : Component Function Check INFOID:0000000001524241
1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

Check that heating wire of passenger side door mirror defogger is heated when turning the rear window defog-
ger switch ON.
DEF-21
YES >> Passenger side door mirror defogger is OK.
NO >> Refer to DEF-22, "PASSENGER SIDE : Diagnosis Procedure".
PASSENGER SIDE : Diagnosis Procedure INFOID:0000000001524242
1.CHECK FUSE
2. Check 10A fuse (No. 6, located in fuse and fusible link box).
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if fuse is blown.
2.CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
2. Check voltage between door mirror (passenger side) harness connector and ground.
Door mirror (passenger side) Condition of rear win- Voltage (V)

Ground
Connector Terminal dow defogger switch (Approx.)
LHD D43 ON Battery voltage

7 Ground
RHD D63 OFF 0
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
2. Disconnect door mirror (passenger side) connector.
3. Check continuity between door mirror (passenger side) harness connector and ground.
Door mirror (passenger side)

Ground Continuity
Connector Terminal
LHD D43
8 Ground Existed
RHD D63
YES >> GO TO 4.
NO >> Repair or replace harness between door mirror (passenger side) and ground.
4.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER
Check passenger side door mirror defogger.
Refer to DEF-23, "PASSENGER SIDE : Component Inspection".
YES >> GO TO 6.
NO >> Replace door mirror glass (passenger side). Refer to MIR-20, "Removal and Installation".
5.CHECK DOOR MIRROR CIRCUIT
2. Disconnect IPDM E/R connector and door mirror (passenger side) connector.
3. Check continuity between door mirror (passenger side) harness connector and IPDM E/R harness con-
nector.
Door mirror (passenger side) IPDM E/R

Continuity
LHD D43
7 E14 49 Existed
RHD D63
4. Check continuity between door mirror (passenger side) harness connector and ground.
DEF-22
Door mirror (passenger side) A

Ground Continuity
Connector Terminal
LHD D43
7 Ground Not existed B
RHD D63
YES >> GO TO 6. C
NO >> Repair or replace harness between door mirror (passenger side) and IPDM E/R.
6.CHECK INTERMITTENT
Refer to GI-39, "Intermittent Incident" D
>> INSPECTION END

E
PASSENGER SIDE : Component Inspection INFOID:0000000001524243
1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER F

2. Disconnect door mirror (passenger side) connector.
3. Check continuity between door mirror connector. G
Door mirror (passenger side)

Continuity
Connector Terminal H
LHD D43
7 8 Existed
RHD D63
I
NO >> Replace door mirror glass (passenger side). Refer to MIR-20, "Removal and Installation".
J
DEF
DEF-23
REAR WINDOW DEFOGGER ON SIGNAL
WITH AUTO A/C
WITH AUTO A/C : Description INFOID:0000000001189073
Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
WITH AUTO A/C : Component Function Check INFOID:0000000001189074
1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamps of rear window defogger switch are illuminated when turning the rear window
defogger switch ON.
OK >> Rear window defogger ON signal is OK.
NG >> Refer to DEF-24, "WITH AUTO A/C : Diagnosis Procedure"
WITH AUTO A/C : Diagnosis Procedure INFOID:0000000001189075
1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMPS ON SIGNAL

2. Check voltage between auto amp. harness connector and ground.
Auto amp. Voltage (V)

Ground Condition
Rear window defogger switch is pressed. Battery voltage

M53 22 Ground
Rear window defogger switch is OFF. 0
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER INDICATOR LAMPS CIRCUIT
2. Disconnect IPDM E/R connector and auto amp. connector.
3. Check continuity between IPDM E/R harness connector and auto amp. harness connector.
IPDM E/R Auto amp.

Continuity
E14 49 M53 22 Existed
4. Check continuity between BCM harness connector and ground.
IPDM E/R
Ground Continuity
Connector Terminal
YES >> GO TO 3.
NO >> Repair or replace harness between IPDM E/R and auto amp.
>> INSPECTION END.

WITHOUT AUTO A/C
DEF-24
WITHOUT AUTO A/C : Description INFOID:0000000001189076
A
Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
WITHOUT AUTO A/C : Component Function Check INFOID:0000000001189077
B
1.CHECK REAR WINDOW DEFOGGER ON SIGNAL
Check that the indicator lamps of rear window defogger switch are illuminated when turning the rear window
C
defogger switch ON.
OK >> Rear window defogger ON signal is OK. D
NG >> Refer to DEF-25, "WITHOUT AUTO A/C : Diagnosis Procedure"
WITHOUT AUTO A/C : Diagnosis Procedure INFOID:0000000001189078
E
1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMPS ON SIGNAL
2. Check voltage between heater control panel harness connector and ground. F
Heater control panel Voltage (V)

Ground Condition
Connector Terminal (Approx.) G
Rear window defogger switch is ON. Battery voltage
M54 19 Ground
Rear window defogger switch is OFF. 0
H
YES >> GO TO 3.
NO >> GO TO 2. I
2.CHECK REAR WINDOW DEFOGGER LAMPS CUIRCUIT
2. Disconnect IPDM E/R connector and heater control panel connector. J
3. Check continuity between IPDM E/R harness connector and heater control panel harness connector.
IPDM E/R Heater control panel K

Continuity
E14 49 M54 19 Existed
DEF
4. Check continuity between BCM connector and ground
IPDM E/R
Ground Continuity M
Connector Terminal
Is the inspection result normal? N
YES >> GO TO 3.
NO >> Repair or replace harness between IPDM E/R and heater control panel.
3.CHECK IINTERMITTENT INCDENT O
P
>> INSPECTON END.
DEF-25
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS
Reference Value INFOID:0000000001555046
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status

Ignition switch OFF Off
ACC ON SW
Ignition switch ACC or ON On
A/C switch OFF Off
AIR COND SW
A/C switch ON On
Outside of the room is bright Off
AUT LIGHT SYS
Outside of the room is dark On
Lighting switch OFF Off
AUTO LIGHT SW
Lighting switch AUTO On
Auto lock function does not operate Off
AUTO RELOCK
Auto lock function is operating On
Back door closed Off
BACK DOOR SW
Back door opened On
BATTERY VOLT
NOTE: Approximately the same as power
Ignition switch ON
Diesel engine models supply voltage
only
Brake pedal is not depressed Off
BRAKE SW
Brake pedal is depressed On
Door lock/unlock switch does not operate Off
CDL LOCK SW
Press door lock/unlock switch to the LOCK side On
Door lock/unlock switch does not operate Off
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side On
Passenger door closed Off
DOOR SW-AS
Passenger door opened On
Driver door closed Off
DOOR SW-DR
Driver door opened On
Rear LH door closed Off
DOOR SW-RL
Rear LH door opened On
Rear RH door closed Off
DOOR SW-RR
Rear RH door opened On
DEF-26
< ECU DIAGNOSIS >
A
Fan switch ON (when engine coolant is
cool)
NOTE: Off
Depending on the ambient tempera- B
ture, battery voltage, etc.
ELEC PWR CUT The current status maintained with the
FREEZ
NOTE: signal from ECM received.
Diesel engine models
Engine running C
• Fan switch OFF
only
• Fan switch ON after engine warming
UP
NOTE: INHBT D
Depending on the engine coolant
temperature, ambient temperature,
battery voltage, etc.
E
ENG COOLNT T
NOTE: Approximately the same as water
Engine running
Diesel engine models temperature gauge reading
only F
ENGINE RPM
NOTE: Approximately the same as tachom-
Engine running
Diesel engine models eter reading G
only
Engine stopped Off
ENGINE RUN
Engine running On H
Engine stopped STOP
ENGINE STATUS
NOTE: While the engine stalls STALL
Diesel engine models I
Engine running RUN
only
At engine cranking CRA
Fan switch OFF Off J
FAN ON SIG
Fan switch ON On
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On K
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On
DEF
Front wiper switch OFF Off
FR WIPER LOW
Front wiper switch LO On
Front wiper switch OFF Off M
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off
FR WIPER INT N
Front wiper switch INT On
Any position other than front wiper stop position Off
FR WIPER STOP
Front wiper stop position On O
The vehicle without glass break sensor On
GLS BREAK SEN
The vehicle with glass break sensor Off
P
When hazard switch is not pressed Off
HAZARD SW
When hazard switch is pressed On
Displays a setting time of the follow
HD LIGHT TIME — me home function set by the work
support
DEF-27
< ECU DIAGNOSIS >
HEAD LAMP SW 1
Lighting switch 2ND On
HEAD LAMP SW 2
Lighting switch 2ND On
HI BEAM SW
Lighting switch HI On
Close the hood
NOTE: Off
HOOD SW Vehicles without theft warning system are OFF-fixed
Open the hood On
NOTE:
H/L WASH SW Off
The item is indicated, but not monitored
Ignition switch OFF or ACC Off
IGN ON SW
Ignition switch ON On
IGN SW CAN
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
LOCK button of Intelligent Key is not pressed Off
I-KEY LOCK
LOCK button of Intelligent Key is pressed On
UNLOCK button of Intelligent Key is not pressed Off
I-KEY UNLOCK
UNLOCK button of Intelligent Key is pressed On
Mechanical key is removed from key cylinder Off
KEY ON SW
Mechanical key is inserted to key cylinder On
LOCK button of key fob is not pressed Off
KEYLESS LOCK
LOCK button of key fob is pressed On
NOTE:
KEY LESS PANIC Off
The item is indicated, but not monitored
UNLOCK button of key fob is not pressed Off
KEYLESS UNLOCK
UNLOCK button of key fob is pressed On
Light & rain sensor is in normal condition OK
LIT-SEN FAIL
Light & rain sensor is with internal error NOT OK
Key fob ID code is not registered in “Memory 1” Off
MEMORY 1
Key fob ID code is registered in “Memory 1” On
MEMORY 2
MEMORY 3
MEMORY 4
MEMORY 5
• Ignition switch OFF or ACC
Off
OIL PRESS SW • Engine running
OUT SIDE TEMP
Approximately the same as outside
NOTE: Ignition switch ON
air temperature
Diesel engine models
DEF-28
< ECU DIAGNOSIS >
A
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Except selector lever R position Off B
REVERSE SW CAN
Selector lever R position On
Return to ignition switch to LOCK position Off
PUSH SW
Press ignition switch On C
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On
D
Rear fog lamp switch OFF Off
RR FOG SW
Rear fog lamp switch ON On
Rear washer switch OFF Off E
RR WASHER SW
Rear washer switch ON On
Rear wiper switch OFF Off
RR WIPER INT F
Rear wiper switch INT On
Rear wiper switch OFF Off
RR WIPER ON
Rear wiper switch ON On G
Rear wiper stop position Off
RR WIPER STOP
Other than rear wiper stop position On
H
Ignition switch ON NOMAL
After the reception of air bag deployment signal from air bag diag-
Off
SHOCK SENSOR nosis sensor unit
I
During the reception of air bag deployment signal from air bag diag-
On
nosis sensor unit
TAIL LAMP SW J
Lighting switch 1ST On
When back door opener switch is not pressed Off
TRNK OPNR SW
When back door opener switch is pressed On K
Turn signal switch OFF Off
TURN SIGNAL L
Turn signal switch LH On
DEF
Turn signal switch OFF Off
TURN SIGNAL R
Turn signal switch RH On
Other than the following Off M
UNLOCK SHOCK
During the unlock operation interlocked with air bag On
VEHICLE SPEED While driving Equivalent to speedometer reading
N
DEF-29
< ECU DIAGNOSIS >
TERMINAL LAYOUT
JPMIA0145GB
PHYSICAL VALUES
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter-
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT-III. Refer to
BCS-27, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-10, "Sys-
tem Description".
DEF-30
< ECU DIAGNOSIS >
Terminal No. Description A

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF B
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4) C
Rear wiper switch INT
1 Combination switch Combination (Wiper intermittent dial 4)
Ground Output
(P) OUTPUT 1 switch Any of the condition below D
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 3 JPMIA0160GB E
• Wiper intermittent dial 6 9.1 V
All switch OFF 0V F
Lighting switch 2ND
Lighting switch PASS
Combination
2 Combination switch switch Front fog lamp switch ON G
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH H
JPMIA0163GB
9.3 V
All switch OFF 0V I
Lighting switch AUTO
Rear fog lamp switch OFF
Combination J
3 Combination switch switch Front wiper switch MIST
Ground Output
(LG) OUTPUT 3 (Wiper intermit- Front wiper switch INT
tent dial 4)
K
Front wiper switch LO JPMIA0162GB
9.3 V
All switch OFF DEF
0V
Front washer switch ON
(Wiper intermittent dial 4) M
Rear wiper switch ON
4 Combination switch Combination
Ground Output
(R) OUTPUT 2 switch Rear washer switch ON N
Any of the condition below
with all switch OFF
JPMIA0161GB O
9.1 V
P
DEF-31
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
+ − Output
All switch OFF 0V
Lighting switch 1ST
Lighting switch 2ND
Combination
5 Combination switch switch Lighting switch HI
Ground Output
(W) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0164GB
9.1 V
7 Door lock/unlock Door lock/un- Not pressed

Ground
(P) switch (Lock) Input lock switch
JPMIA0154GB
1.2 V
Pressed to the lock side 0V
8 Not pressed
Ground Hazard switch Input Hazard switch
(LG)
JPMIA0154GB
1.3 V
Pressed 0V
9 Door lock/unlock Door lock/un- Not pressed

Ground
(BR) switch (Unlock) Input lock switch
JPMIA0154GB
1.2 V
Pressed to the unlock side 0 V
12 Back door opener Back door Not pressed

Ground Input
(P) switch opener switch
JPMIA0154GB
1.2 V
Pressed 0V
DEF-32
< ECU DIAGNOSIS >
(Wire color) Value A
Input/ Condition
+ − Output
Ignition switch OFF or ACC 0V
B
13
Ground Shock detect sensor Input
C
(R) Ignition switch ON
D
JPMIA0155GB
6.0 V
14 Not pressed Battery voltage

Ground A/C switch Input A/C switch E
(L/R) Pressed 0V
15 Not pressed Battery voltage

Ground Fan switch Input Fan switch
(LG/B) Pressed 0V F
16
Ground Alarm link Output — —
(GR)
Ignition switch OFF or ACC Battery voltage G
H
17 Light & rain sensor Input/
Ground
(BR) serial link Output Ignition switch ON
I
JPMIA0156GB
8.7 V
ON 0V J
K
18 Security indica-
Ground Security indicator Output Blinking
(SB) tor
DEF
JPMIA0014GB
10.3 V
M
OFF Battery voltage
19 Input/
— CAN-H — —
(L) Output
N
20 Input/
— CAN-L — —
(P) Output
21 Rear window defog- Rear window Not pressed P

Ground Input
(SB) ger switch defogger switch
JPMIA0154GB
1.1 V
While pressing 0V
DEF-33
< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ − Output
24 Door lock status indi- Door lock status ON Battery voltage

Ground Output
(GR) cator indicator OFF 0V
OFF (When rear door LH

25 Rear door closed)
Ground Rear door switch LH Input
(GR) switch LH
PKID0924E
11.2 V
ON (When rear door LH
0V
opened)
OFF (When driver door

26 Driver door closed)
Ground Driver door switch Input
(R) switch
PKID0924E
11.2 V
ON (When driver door
0V
opened)
OFF (When passenger

27 Passenger door Passenger door door closed)
Ground Input
(BR) switch switch
PKID0924E
11.2 V
ON (When passenger
0V
door opened)
OFF (When back door
Battery voltage
28 Back door closed)
Ground Back door switch Input
(G) switch ON (When back door
0V
opened)
OFF (When rear door RH

29 Rear door closed)
Ground Rear door switch RH Input
(LG) switch RH
PKID0924E
11.2 V
ON (When rear door RH
0V
opened)
30 Input/
Ground Audio link — — —
(SB) Output
DEF-34
< ECU DIAGNOSIS >
Input/ Condition
+ − Output
All switch OFF

JPMIA0165GB
1.3 V D
E
Front fog lamp switch ON
F
JPMIA0167GB
1.3 V
G
31 Combination switch Combination Rear fog lamp switch ON

H
Ground Input
(BR) INPUT 5 switch (Wiper intermittent dial 4)
JPMIA0168GB
I
1.3 V

(Wiper intermittent dial 4) K
JPMIA0169GB
1.3 V DEF

M
with all switch OFF
• Wiper intermittent dial 6 N
JPMIA0196GB
1.3 V
O
DEF-35
< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ − Output
All switch OFF
JPMIA0165GB
1.4 V
Lighting switch PASS
JPMIA0167GB
1.3 V
Combination
32 Combination switch switch
Ground Input Lighting switch 2ND
(G) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0166GB
1.3 V
Front wiper switch INT
JPMIA0168GB
1.3 V
Front wiper switch HI
JPMIA0196GB
1.3 V
DEF-36
< ECU DIAGNOSIS >
Input/ Condition
+ − Output
All switch OFF C
JPMIA0165GB
1.4 V D
Turn signal switch LH
F
JPMIA0167GB
1.3 V
G
Combination
33 Combination switch switch
H
Ground Input Turn signal switch RH
(V) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0166GB
I
1.3 V
Front wiper switch LO

K
JPMIA0168GB
1.3 V DEF
Front washer switch ON
N
JPMIA0196GB
1.3 V
O
DEF-37
< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ − Output
All switch OFF

JPMIA0165GB
1.4 V
Lighting switch AUTO

JPMIA0167GB
1.3 V
34 Combination switch Combination Lighting switch 1ST

Ground Input
(GR) INPUT 4 switch (Wiper intermittent dial 4)
JPMIA0166GB
1.3 V
Rear wiper INT

JPMIA0167GB
1.3 V

with all switch OFF
JPMIA0196GB
1.3 V
DEF-38
< ECU DIAGNOSIS >
Input/ Condition
+ − Output
All switch OFF

JPMIA0165GB
1.4 V D
E
Lighting switch HI
F
JPMIA0166GB
1.3 V
G
35 Combination switch Combination Lighting switch 2ND

H
Ground Input
(L) INPUT 3 switch (Wiper intermittent dial 4)
JPMIA0167GB
I
1.3 V

K
JPMIA0169GB
1.3 V DEF
Any of the condition below M

with all switch OFF
• Wiper intermittent dial 3 N
JPMIA0196GB
1.3 V
Insert mechanical key into ignition key cylin- O
Battery voltage
36 der
Ground Key switch Input
(V) Remove mechanical key from ignition key
0V
cylinder P
37 Ignition switch OFF 0V
Ground ACC power supply Input
(R) Ignition switch ACC or ON Battery voltage
38 Ignition power sup- Ignition switch OFF or ACC 0V

Ground Input
(W) ply Ignition switch ON Battery voltage
DEF-39
< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ − Output
Just after Insert mechanical key
39 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(P) Output der
of tester should move
Just after Insert mechanical key
40 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(LG) Output der
of tester should move
41 Battery power sup-
Ground Input Ignition switch OFF Battery voltage
(V) ply
After passing the interior room lamp battery
0V
42 Interior room lamp saver operation time
Ground Output
(V) power supply Any other time after passing the interior room
Battery voltage
lamp battery saver operation time
43 Rear wiper switch OFF 0V

Ground Rear wiper motor Output
(L) Rear wiper switch ON Battery voltage
Rear wiper stop position 0V
44 Ignition switch
Ground Rear wiper auto stop Input Any position other than
(L/W) ON
rear wiper stop position
JPMIA0197GB
45 Back door lock actu- Back door Pressed Battery voltage (300ms)
Ground Output
(GR) ator opener switch Not pressed 0V
Turn signal switch OFF 0V
47 Ignition switch
Ground Turn signal LH Output
(G/Y) ON Turn signal switch LH
PKID0926E
6.5 V
Turn signal switch OFF 0V
48 Ignition switch
Ground Turn signal RH Output
(G/B) ON Turn signal switch RH
PKID0926E
6.5 V
Lighting switch Rear fog lamp switch OFF 0 V
49 1ST and front
Ground Rear fog lamp Output
(Y) fog lamp switch Rear fog lamp switch ON Battery voltage
ON
51 Depress the brake pedal Battery voltage
(R/W)*1 Ground Stop lamp switch Input
(R)*2 Release the brake pedal 0V
DEF-40
< ECU DIAGNOSIS >
Input/ Condition
+ − Output
52 Room lamp timer Interior room OFF Battery voltage

(R)
Ground
control
Output
lamp
B
ON 0V
53 Power window pow- OFF or ACC 0V

Ground Output Ignition switch
(L) er supply ON Battery voltage C
54 Door lock/un- Pressed to the unlock side Battery voltage
Ground Door unlock (All) Output
(O) lock switch Pressed to the lock side 0V
D
55
Ground Ground — Ignition switch ON 0V
(B)
56 Pressed to the unlock side 0V
(Y)*1 Ground Door lock (All) Output
Door lock/un- E
lock switch Pressed to the lock side Battery voltage
(SB)*2
57 Battery power sup-
Ground Input Ignition switch OFF Battery voltage F
(Y) ply
58 Power window pow-
Ground Output Ignition switch OFF Battery voltage
(P) er supply
When lock button of key fob or Intelligent Key
G
0V
59 is not pressed
Ground Super lock Output
(BR) When lock button of key fob or Intelligent Key
Battery voltage H
is pressed
60 Door lock/un- Pressed to the unlock side Battery voltage

Ground Driver door unlock Output
(GR) lock switch Pressed to the lock side 0V
I
*1: With Intelligent Key system
*2: Without Intelligent Key system
DEF
DEF-41
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (LHD MODELS) - INFOID:0000000001189080
JCLWA0404GB
DEF-42
< ECU DIAGNOSIS >
DEF
JCLWA0649GB
DEF-43
< ECU DIAGNOSIS >
JCLWA0650GB
DEF-44
< ECU DIAGNOSIS >
DEF
JCLWA0651GB
DEF-45
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (RHD MODELS) - INFOID:0000000001189081
JCLWA0408GB
DEF-46
< ECU DIAGNOSIS >
DEF
JCLWA0652GB
DEF-47
< ECU DIAGNOSIS >
JCLWA0653GB
DEF-48
< ECU DIAGNOSIS >
DEF
JCLWA0654GB
Fail Safe INFOID:0000000001555087 P
Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.
DEF-49
< ECU DIAGNOSIS >
Display contents of CONSULT Fail-safe Cancellation

• Inhibits engine cranking
B2190: NATS ANTENNA AMP • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B2191: DIFFERENCE OF KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B2192: ID DISCORD BCM-ECM Fuel cut (ECM) Erase DTC
B2193: CHAIN OF BCM-ECM Fuel cut (ECM) Erase DTC
B2194: DISCORD BCM-I-KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B2195: ANTI SCANNING • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B2196: DONGLE NG • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
REAR WIPER CONTROL

BCM detects a rear wiper stopping position according to a rear wiper auto stop signal.
When a rear wiper auto stop signal is in the condition listed below, BCM stops power supply to rear wiper after
rear wiper is activated for five seconds.
Ignition switch Rear wiper switch Rear wiper auto stop signal
The rear wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 5 seconds.
ON
The rear wiper auto stop signal does not
ON
change for 5 seconds.
NOTE:
The above operation is repeated when operating the rear wiper switch one minute after the stop of the rear
wiper caused by Fail-safe.
TURN SIGNAL LAMP CONTROL
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
LIGHT & RAIN SENSOR MALFUNCTION DETECTION FUNCTION
BCM controls the following items when LIGHT & RAIN sensor has a malfunction.
Auto Light Control
Headlamp is turned ON.
Front Wiper Control
The condition just before the activation of Fail-safe is maintained until the front wiper switch is turned OFF.
DEF-50
< ECU DIAGNOSIS >
DTC Inspection Priority Chart INFOID:0000000001555088
Priority DTC
• U1000: CAN COMM CIRCUIT B
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERNCE OF KEY C
• B2192: ID DISCORD BCM-ECM
2 • B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING D
• B2196: DONGLE NG
DTC Index INFOID:0000000001555089

E
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- F
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
G
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
H
CONSULT display TIME Fail-safe Refer to
No DTC is detected.
further testing — — — — I
may be required.
U1000: CAN COMM CIRCUIT 0 1 - 39 — BCS-33
U1010: CONTROL UNIT (CAN) 0 1 - 39 — BCS-34 J
• With Intelligent Key system SEC-45
B2190: NATS ANTENNA AMP CRNT PAST × • Without Intelligent Key system SEC-
194 K
B2191: DIFFERENCE OF KEY CRNT PAST × • Without Intelligent Key system SEC-
196
DEF
B2192: ID DISCORD BCM-ECM CRNT PAST × • Without Intelligent Key system SEC-
197
M
B2193: CHAIN OF BCM-ECM CRNT PAST × • Without Intelligent Key system SEC-
199
B2194: DISCORD BCM-I-KEY CRNT PAST × SEC-51 N
B2195: ANTI SCANNING CRNT PAST × • Without Intelligent Key system SEC-
200 O
B2196: DONGLE NG CRNT PAST × • Without Intelligent Key system SEC-
201 P
DEF-51
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference Value INFOID:0000000001555125
VALUES ON THE DIAGNOSIS TOOL

Changes depending on engine
coolant temperature, air condition-
MOTOR FAN REQ Engine idle speed 1-3
er operation status, vehicle speed,
etc.
A/C switch OFF Off
AC COMP REQ Engine running A/C switch ON
On
(Compressor is operating)
TAIL&CLR REQ
Lighting switch 1ST, 2ND or AUTO (Light is illuminated) On
HL LO REQ
Lighting switch 2ND or AUTO (Light is illuminated) On
HL HI REQ
Lighting switch HI (Light is illuminated) On
Lighting switch 2ND or Front fog lamp switch OFF Off

FR FOG REQ
AUTO (Light is illuminated) Front fog lamp switch ON On
Front washer switch OFF Off
Ignition switch ON, and low Front washer switch ON
HL WASHER REQ
beam headlamp is ON (When headlamp washer is operat- On
ing)
Front wiper switch OFF STOP
Front wiper switch INT 1LOW
FR WIP REQ Ignition switch ON
Front wiper switch LO Low
Front wiper switch HI Hi
Front wiper stop position STOP P
WIP AUTO STOP Ignition switch ON Any position other than front wiper
ACT P
stop position
Front wiper operates normally Off
WIP PROT Ignition switch ON Front wiper stops due to fail-safe
BLOCK
operation (cut-out operation)
ST RLY REQ When Intelligent Key is outside the vehicle, and the push switch
Off
NOTE: is pushed
Vehicle without Intelligent Key system indi- When Intelligent Key is inside the vehicle, and the push switch is
cates only “ON”, and it does not change. On
pushed
IGN RLY
Rear window defogger switch OFF Off
RR DEF REQ Ignition switch ON Rear window defogger switch ON

(Rear window defogger is operat- On
ing)
Ignition switch OFF, ACC or engine running Open
OIL P SW
Ignition switch ON Close
DEF-52
< ECU DIAGNOSIS >
A
Except selector lever R position Off
REV SW
Selector lever R position On
HOOD SW Close the hood Off B
NOTE:
This item is monitored only on the vehicle
with the Vehicle Security (Theft Warning) Open the hood On
system. C
THFT HRN REQ Not operation Off
NOTE:
This item is monitored only on the vehicle D
with the Vehicle Security (Theft Warning) Horn is activated with Vehicle Security (Theft Warning) system. On
system.
NOTE:
HORN CHIRP Off E
This item is indicated, but not monitored.
IGN ON SW
F
DEF
DEF-53
< ECU DIAGNOSIS >
TERMINAL LAYOUT
JPMIA0236GB
PHYSICAL VALUES

(Wire color) Value
Input/ Condition
+ − Output
1
Ground Battery power supply Input Ignition switch OFF Battery voltage
(G)
2
Ground Battery power supply Input Ignition switch OFF Battery voltage
(R)
5
Ground Ground — Ignition switch ON 0V
(B)
DEF-54
< ECU DIAGNOSIS >
Input/ Condition
+ − Output
6
Ground Ground — Ignition switch ON 0V B
(B)
7 Front wiper switch OFF 0V

Ground Front wiper LO Output Ignition switch ON
(Y) Front wiper switch LO Battery voltage
C
8 Front wiper switch OFF 0V
Ground Front wiper HI Output Ignition switch ON
(Y/R) Front wiper switch HI Battery voltage
9 D
Ground ECM relay power supply Output Ignition switch ON Battery voltage
(G)
10*1 Ground ECM relay power supply Output Ignition switch ON Battery voltage
(L/R) E
11*2 PTC heater OFF Battery voltage
Ground PTC heater 1 relay control Output
(O) PTC heater ON 0V
F
12*2 PTC heater OFF Battery voltage
Ground PTC heater 2 relay control Output
(G/Y) PTC heater ON 0V
14 Ignition switch OFF or ACC 0V G

Ground Ignition power supply Output
(R/B) Ignition switch ON Battery voltage
• Engine running 0 - 1.0 V*1
• Ignition switch OFF H
15 (For a few seconds after turning ignition switch 2
0.6 V*
(Y/L)*1 Ground ECM relay control Input OFF)
(B/R)*2 Ignition switch OFF or ACC
I
(More than a few seconds after turning ignition Battery voltage
switch OFF)
16*3 Ignition switch ON Battery voltage

Ground Ignition relay power supply Output J
(Y/R) Ignition switch OFF or ACC 0V
19*1 Ignition switch ON Battery voltage

Ground Ignition relay power supply Output
(R/O) Ignition switch OFF or ACC 0V K
0 V → Battery volt-
21*4 Close the hood
Ground Hood switch Input age → 0 V
(GR)
Open the hood 0V DEF
Ignition switch OFF or ACC 0V
• Selector lever “R”
(Except M/T models) M
Battery voltage
• M/T control lever “R”
(M/T models)
22
Ground Reverse switch Input
(Y/G) Ignition switch ON • Selector lever in any po- N
sition other than “R” (Ex-
cept M/T models)
0V
• M/T control lever in any
position other than “R” O
(M/T models)
Engine stopped 0V
A/C switch OFF 0V P
23
Ground A/C relay power supply Output
(Y/B) Engine running A/C switch ON
(A/C compressor is oper- Battery voltage
ating)
24 Lighting switch OFF 0V

Ground Headlamp LO (RH) Output
(R/Y) Lighting switch 2ND Battery voltage
DEF-55
< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ − Output
25*1 Ignition switch OFF or ACC Battery voltage

Ground ETC relay control Input
(G/L) Ignition switch ON 0 - 1.0 V
Front wiper stop position 0V
26
Ground Front wiper auto stop Input Ignition switch ON Any position other than
(O) Battery voltage
front wiper stop position
27 Engine stopped 0V
Ground Oil pressure switch Input
(W) Engine running Battery voltage
28 Input/
— CAN-H — —
(L) Output
29 Input/
— CAN-L — —
(P) Output
30*4 The horn is not activated Battery voltage

Ground Horn relay control Output
(L) The horn is activated 0V

Ground Headlamp LO (sensor) Output
(R) Lighting switch 2ND Battery voltage
32*1 Ground ETC relay power supply Output Ignition switch ON Battery voltage
(R/Y)
• Engine running
• Ignition switch ON 0 - 1.0 V
33*1 (For 1 second after turning ignition switch ON)
Ground Fuel pump relay control Input
(B/O) Ignition switch ON
(More than 1 second after turning ignition switch Battery voltage
ON)
Ignition switch ON Selector lever “P” or “N” Battery voltage

34 (Except M/T mod- Selector lever in any posi-
Ground Starter relay power supply Input els) 0V
(R/B) tion other than “P” or “N”
Ignition switch ON (M/T models) Battery voltage
35 Ignition switch OFF or ACC 0V

Ground Ignition switch ON Input
(W/L) Ignition switch ON Battery voltage
36 Front fog lamp switch ON Battery voltage

Ground Front fog lamp (RH) Output Lighting switch 1ST
(W) Front fog lamp switch OFF 0V
37 Lighting switch 1ST Battery voltage

Ground Parking lamp (RH) Output
(R/W) Lighting switch OFF 0V
38 Tail, license plate lamps Lighting switch 1ST Battery voltage

Ground Output
(R/L) and illuminations Lighting switch OFF 0V
When headlamp washer is
0V
39 Headlamp washer relay operating
Ground Output Ignition switch ON
(GR) control When headlamp washer is
Battery voltage
not operating
40*1 Ignition switch OFF or ACC 0V

5 Ground Ignition relay power supply Output
(BR/Y)*
Ignition switch ON Battery voltage
(SB)*6
41 Ignition switch OFF or ACC 0V

Ground Ignition relay power supply Output
(P) Ignition switch ON Battery voltage
DEF-56
< ECU DIAGNOSIS >
Input/ Condition
+ − Output
• Ignition switch OFF or ACC
• Approximately 1 second or more after turning 0V B
42*1 Fuel pump relay power the ignition switch ON
Ground Output
(B/Y) supply • Approximately 1 second after turning the igni-
tion switch ON Battery voltage C
• Engine running
43 Front fog lamp switch ON Battery voltage

Ground Front fog lamp (LH) Output Lighting switch 1ST
(W/B) Front fog lamp switch OFF 0V D
Ground Headlamp LO (LH) Output
(L) Lighting switch 2ND Battery voltage
E
• Lighting switch 2ND and HI
45 Battery voltage
Ground Headlamp HI (RH) Output • lighting switch PASS
(L/W)
Lighting switch OFF 0V
F
• Lighting switch 2ND and HI
46 Battery voltage
Ground Headlamp HI (LH) Output • Lighting switch PASS
(G)
Lighting switch OFF 0V
G
47 Lighting switch 1ST Battery voltage
Ground Parking lamp (LH) Output
(R/L) Lighting switch OFF 0V
When cooling fan does HI operation 0V H
48*7 Ground Cooling fan relay-3 control Output
(Y) When cooling fan does OFF or LO operation Battery voltage
Rear window defogger
Battery voltage I
49 Rear window defogger re- switch ON
Ground Output Ignition switch ON
(B) lay power supply Rear window defogger
0V
switch OFF
J
50 When engine is cranking Battery voltage
Ground Starter relay power supply Output
(B/R) When engine is not cranking 0V
51 Ignition switch START Battery voltage K

Ground Ignition switch START Input
(P) Ignition switch OFF, ACC or ON 0V
52 Cooling fan relay-1 power When cooling fan does LO or HI operation Battery voltage
Ground Output DEF
(W) supply When cooling fan does OFF operation 0V
53 Battery power supply
Ground Input Ignition switch OFF Battery voltage
(W/B) (Cooling fan relay)
M
54*5 Cooling fan relay-2 power When cooling fan does HI operation Battery voltage
Ground Input
(R) supply When cooling fan does OFF or LO operation 0V
*1: HR engine and MR engine models N

*2: K9K engine and M9R engine models
*3: Except M/T models only
*4: With vehicle security (theft warning) system
O
*5: HR engine models

*6: MR engine models
P
*7: MR engine, K9K engine and M9R engine models
DEF-57
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (LHD MODELS) - INFOID:0000000001189086
JCLWA0404GB
DEF-58
< ECU DIAGNOSIS >
DEF
JCLWA0649GB
DEF-59
< ECU DIAGNOSIS >
JCLWA0650GB
DEF-60
< ECU DIAGNOSIS >
DEF
JCLWA0651GB
DEF-61
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (RHD MODELS) - INFOID:0000000001189087
JCLWA0408GB
DEF-62
< ECU DIAGNOSIS >
DEF
JCLWA0652GB
DEF-63
< ECU DIAGNOSIS >
JCLWA0653GB
DEF-64
< ECU DIAGNOSIS >
DEF
JCLWA0654GB
Fail Safe INFOID:0000000001555126 P
CAN communication control

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If no CAN communication is available with ECM
DEF-65
< ECU DIAGNOSIS >
Control part Fail-safe in operation
• The cooling fan relay-2*1 or the cooling fan relay-3*2 turns ON when the ignition switch
Cooling fan is turned ON
• Turns off the fan motor low relay when the ignition switch is turned OFF
A/C compressor A/C relay OFF
*1: HR engine models
*2: MR engine, K9K engine and M9R engine models
If no CAN communication is available with BCM
Control part Fail-safe in operation

• The headlamp low relay turns ON when the ignition switch is turned ON
Headlamp • The headlamp low relay turns OFF when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamps
• License plate lamps • The tail lamp relay turns ON when the ignition switch is turned ON
• Tail lamps • The tail lamp relay turns OFF when the ignition switch is turned OFF
• Illuminations
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The front wiper is operated at LO speed until the ignition switch is turned OFF if the
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Front fog lamps Front fog lamp relay OFF
Starter motor Starter relay OFF
Rear window defogger Rear window defogger relay OFF
Headlamp washer Headlamp washer relay OFF
PTC heater PTC heater relay OFF
Ignition relay malfunction detection function

• The CPU integrated IPDM E/R monitors the voltage at the contact circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the ignition relay condition is different from the ignition switch ON
signal.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
DTC Ignition switch Ignition relay Tail lamp relay

— ON ON —
— OFF OFF —
— OFF ON ON (10 minutes)
B2099: IGN RLY OFF ON OFF —
NOTE:
The tail lamp relay is turned OFF when the ignition switch is turned ON.
Front wiper control

IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop until ignition switch is turned OFF.
Ignition switch Front wiper switch Front wiper auto stop signal
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not
ON
change for 10 seconds.
NOTE:
DEF-66
< ECU DIAGNOSIS >
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped. A
DTC Index INFOID:0000000001555127
B
CONSULT display Fail-safe TimingNOTE Reference page
No DTC is detected.
further testing — — — — C
may be required.
U1000: CAN COMM CIRCUIT × CRNT PAST PCS-14
B2099: IGN RELAY OFF — CRNT PAST PCS-15 D
B209A: RAM ERROR — CRNT PAST PCS-16
B209B: ROM ERROR — CRNT PAST PCS-17 E
B2100: EEPROM — CRNT PAST PCS-18
NOTE:
The details of time display are as follows. F
• CRNT: The malfunctions that are detected now.
• PAST: The number is indicated when it is normal at present and a malfunction was detected in the past.
G
DEF
DEF-67
REAR WINDOW DEFOGGER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
REAR WINDOW DEFOGGER DOES NOT OPERATE
1.IPDM E/R AUTO ACTIVE TEST

Perform IPDM E/R active test.
Refer to PCS-9, "Diagnosis Description".
YES >> GO TO 2.
Check rear window defogger switch.
With auto A/C. Refer to DEF-13, "WITH AUTO A/C : Component Function Check".
Without auto A/C. Refer to DEF-15, "WITHOUT AUTO A/C : Component Function Check"
YES >> GO TO 3.
3.CHECK REAR WINDOW DEFOGGER RELAY
Check rear window defogger relay.
Refer to DEF-17, "Component Function Check".
YES >> GO TO 4.
Check rear window defogger.
YES >> GO TO 5.
5.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident.Refer to GI-39, "Intermittent Incident"
NO >> GO TO 1.
DEF-68
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPER-
ATE.
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT
A
OPERATE.
B
1.IPDM E/R AUTO ACTIVE TEST
Perform IPDM E/R active test.
C
Refer to PCS-9, "Diagnosis Description".
YES >> GO TO 2. D
Check rear window defogger switch. E
With auto A/C. Refer to DEF-13, "WITH AUTO A/C : Component Function Check".
Without auto A/C. Refer to DEF-15, "WITHOUT AUTO A/C : Component Function Check".
Is the inspection result normal? F
YES >> GO TO 3.
3.CHECK REAR WINDOW DEFOGGER RELAY G
Check rear window defogger relay.
Refer toDEF-17, "Component Function Check"
H
YES >> GO TO 4.
I
Refer to DEF-18, "Component Function Check". J
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts. K
DEF
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident"
NO >> GO TO 1. M
DEF-69
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIR-
ROR DEFOGGER OPERATE.
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR
MIRROR DEFOGGER OPERATE.

YES >> GO TO 2.
NO >> GO TO 1.
DEF-70
DOOR MIRROR DEFOGGER DOES NOT OPERATE
DOOR MIRROR DEFOGGER DOES NOT OPERATE
A
BOTH SIDE
BOTH SIDE : Diagnosis Procedure INFOID:0000000001524333
B
1.CHECK DOOR MIRROR DEFOGGER
Check door mirror defogger circuit.
Refer to DEF-20, "DRIVER SIDE : Component Function Check" C
YES >> GO TO 2.
D
Confirm the operation again. E
NO >> GO TO 1. F
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure INFOID:0000000001524334 G

Check driver side door mirror defogger. H
Refer to DEF-21, "DRIVER SIDE : Component Inspection".
YES >> GO TO 2. I
J
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident" K
NO >> GO TO 1.
PASSENGER SIDE
DEF
PASSENGER SIDE : Diagnosis Procedure INFOID:0000000001524335
1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER.

M
Check passenger side door mirror defogger.
Refer to DEF-23, "PASSENGER SIDE : Component Inspection"
N
YES >> GO TO 2.
2.CONFIRM THE OPERATION O
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident" P
NO >> GO TO 1.
DEF-71
REAR WINDOW DEFOGGER INDICATOR
REAR WINDOW DEFOGGER INDICATOR
1.CHECK REAR WINDOW DEFOGGER INDICATOR

Check rear window defogger ON signal.
With auto A/R. Refer to DEF-24, "WITH AUTO A/C : Component Function Check".
Without auto A/R. Refer to DEF-25, "WITHOUT AUTO A/C : Component Function Check".
YES >> GO TO 2.
NO >> GO TO 1.
DEF-72
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000001571916
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H
DEF
DEF-73
FILAMENT
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR
FILAMENT
Inspection and Repair INFOID:0000000001189098
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
SEL122R
2. Attach probe circuit tester (in Volt range) to middle portion of

each filament.
SEL263
3. If a filament is burned out, circuit tester registers 0 or battery

voltage.
4. To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
SEL265
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)
DEF-74
FILAMENT
< ON-VEHICLE REPAIR >
• Ruler 30 cm (11.8 in) long
• Drawing pen A
• Heat gun
• Alcohol
• Cloth
B
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol. C
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use. D
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
E
PIIA0215E
F
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited. G
Do not touch repaired area while test is being conducted.
I
SEL012D
5. Apply a constant stream of hot air directly to the repaired area J

for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet. K
If a heat gun is not available, let the repaired area dry for 24
hours.
DEF
M
SEL013D
DEF-75

Defogger: Section

Uploaded by

Copyright:

Available Formats

Defogger: Section

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Defogger: Section

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

SECTION DEF DEFOGGER

System Description INFOID:0000000001189047

Switch Input signal to BCM BCM function Acutuator

Component Description INFOID:0000000001189049 K

Diagnosis mode Function Description

REAR WINDOW DEFOGGER

Monitor Item Description A

Auto active test

Symptom Inspection contents Possible cause

Perform auto active test. • Rear window defogger

CONSULT - III Function (IPDM E/R) INFOID:0000000001555129

Diagnosis mode Description

Monitor Item MAIN A

Test item Operation Description P

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION D

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION H

Rear window defogger switch is pressed. 0

Is the inspection result normal? M

BCM Auto amp.

BCM Voltage (V)

Is the inspection result normal?

>> INSPECTION END

When rear window defogger switch is turned to ON

BCM Voltage (V)

BCM Heater control panel M

Heater control panel

BCM Voltage (V)

Is the inspection result normal?

>> INSPECTION END.

1.CHECK HEATER CONTROL PANEL (REAR WINDOW DEFOGGER SWITCH)

Heater control panel

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION C

>> INSPECTION END O

1.CHECK REAR WINDOW DEFOGGER

1.CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT

Rear window defogger Condition of rear window Voltage (V)

Rear window defogger

IPDM E/R Rear window defogger A

1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Door mirror (driver side) Condition of rear win- Voltage (V)

LHD D3 ON Battery voltage

Door mirror (driver side)

Door mirror (driver side) IPDM E/R C

>> INSPECTION END I

DRIVER SIDE : Component Inspection INFOID:0000000001524239

Door mirror (diver side)

1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

Door mirror (passenger side) Condition of rear win- Voltage (V)

LHD D43 ON Battery voltage

Door mirror (passenger side)

Door mirror (passenger side) IPDM E/R

Door mirror (passenger side) A

>> INSPECTION END

1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER F

Door mirror (passenger side)

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMPS ON SIGNAL

Auto amp. Voltage (V)