Defogger: Section

DRIVER CONTROLS
DEF
A
B
SECTION
DEFOGGER C
E
CONTENTS
PRECAUTION ............................................... 3 List of ECU Reference .............................................11 F
PRECAUTIONS ................................................... 3 WIRING DIAGRAM ...................................... 12

Precaution for Supplemental Restraint System G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- REAR WINDOW DEFOGGER SYSTEM .......... 12
SIONER" ................................................................... 3 Wiring Diagram ........................................................12
Handling for Adhesive and Primer ............................ 3
BASIC INSPECTION ................................... 19 H
SYSTEM DESCRIPTION .............................. 4 DIAGNOSIS AND REPAIR WORKFLOW ........ 19
COMPONENT PARTS ........................................ 4 Work Flow ................................................................19
I
Component Parts Location ........................................ 4
DTC/CIRCUIT DIAGNOSIS ......................... 22
Rear window defogger .............................................. 5
Door mirror defogger ................................................. 5 REAR WINDOW DEFOGGER SWITCH ........... 22 J
SYSTEM .............................................................. 6 WITH MANUAL A/C ...................................................22
System Description ................................................... 6 WITH MANUAL A/C : Description ...........................22
WITH MANUAL A/C : Component Function Check K
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI- ....22
GENT KEY SYSTEM) .......................................... 7 WITH MANUAL A/C : Diagnosis Procedure ............22
COMMON ITEM ........................................................... 7 WITH AUTO A/C ........................................................22 DEF
COMMON ITEM : CONSULT Function (BCM - WITH AUTO A/C : Description ................................22
COMMON ITEM) ....................................................... 7 WITH AUTO A/C : Component Function Check ......22
REAR DEFOGGER ..................................................... 7 WITH AUTO A/C : Diagnosis Procedure .................22 M
REAR DEFOGGER : CONSULT Function (BCM - REAR WINDOW DEFOGGER RELAY ............. 24
REAR DEFOGGER) ................................................. 8 Description ...............................................................24
N
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- Component Function Check ....................................24
TELLIGENT KEY SYSTEM) ................................ 9 Diagnosis Procedure ...............................................24
Component Inspection .............................................25
COMMON ITEM ........................................................... 9 O
COMMON ITEM : CONSULT Function (BCM - REAR WINDOW DEFOGGER POWER SUP-
COMMON ITEM) ....................................................... 9 PLY AND GROUND CIRCUIT .......................... 26
Description ...............................................................26 P
REAR DEFOGGER ..................................................... 9 Component Function Check ....................................26
REAR DEFOGGER : CONSULT Function (BCM - Diagnosis Procedure ...............................................26
REAR DEFOGGER) ................................................. 9 Component Inspection .............................................27
ECU DIAGNOSIS INFORMATION .............. 11 DRIVER SIDE DOOR MIRROR DEFOGGER ... 28
Description ...............................................................28
BCM (BODY CONTROL MODULE) ...................11 Component Function Check ....................................28
Revision: November 2013 DEF-1 2014 Rogue NAM

Diagnosis Procedure .............................................. 28 BOTH DOORS MIRROR DEFOGGER DON’T
Component Inspection ............................................ 29 OPERATE BUT REAR WINDOW DEFOG-
GER OPERATES ............................................... 35
PASSENGER SIDE DOOR MIRROR DEFOG-
Diagnosis Procedure ............................................... 35
GER .................................................................... 30
Description .............................................................. 30 DRIVER SIDE DOOR MIRROR DEFOGGER
Component Function Check ................................... 30 DOES NOT OPERATE. ..................................... 36
Diagnosis Procedure .............................................. 30 Diagnosis Procedure ............................................... 36
Component Inspection ............................................ 31
PASSENGER SIDE DOOR MIRROR DEFOG-
SYMPTOM DIAGNOSIS ............................. 32 GER DOES NOT OPERATE. ............................ 37
DEFOGGER SYSTEM SYMPTOMS ................. 32
Symptom Table ...................................................... 32 REAR WINDOW DEFOGGER SWITCH DOES
REAR WINDOW DEFOGGER AND DOOR NOT LIGHT, BUT REAR WINDOW DEFOG-
MIRROR DEFOGGER DO NOT OPERATE. ..... 33 GER OPERATES ............................................... 38
Diagnosis Procedure .............................................. 33
REAR WINDOW DEFOGGER DOES NOT REMOVAL AND INSTALLATION .............. 39

OPERATE BUT BOTH OF DOOR MIRROR FILAMENT ......................................................... 39
DEFOGGER OPERATE. ................................... 34 Inspection and Repair ............................................. 39
Diagnosis Procedure .............................................. 34
CONDENSER .................................................... 41
Removal and Installation ......................................... 41

PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000010247431
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- H
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery and wait at least three minutes before performing any service.
Handling for Adhesive and Primer INFOID:0000000010247855
J
• Do not use an adhesive which is past its usable date. Shelf life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator. K
• Open the seal of the primer and adhesive just before application. Discard the remainder.
• Before application, be sure to shake the primer container to stir the contents. If any floating material is found,
do not use it.
• If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with DEF
soap.
• When using primer and adhesive, always observe the precautions in the instruction manual.
M

COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000010002209
ALLIA1380ZZ
A. A/C switch (auto A/C) A. Front air control (manual A/C)
No. Component Description

1. Rear window defogger con-
nector Refer to DEF-5, "Rear window defogger".
2. (Rear window defogger)
Rear window defogger con-
3. Removes the noise that is generated when rear window defogger turns ON/OFF.
denser
• Displays the rear window defogger ON to the display when detecting the operation of the
4. A/C auto amp.1 rear window defogger.
• Operates the rear window defogger with the operation of rear window defogger switch.
5. BCM
• Performs the timer control of rear window defogger.
• Operates the rear window defogger and the door mirror defogger with the control signal
6. Rear window defogger relay
from BCM.

COMPONENT PARTS
No. Component Description
A
7. Door mirror defogger3 Refer to DEF-5, "Door mirror defogger".
8. A/C switch1 (rear window de- • The rear window defogger switch is turned ON.
fogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
B
9. Front air control2 (rear window • The rear window defogger switch is turned ON.
defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
1:
With auto A/C C
2: With manual A/C
3: With heated mirrors
D
Rear window defogger INFOID:0000000010284255
Heats the heating wire with the power supply from the rear window E
defogger relay to prevent the rear window from fogging up.
JMLIA2595GB H
Door mirror defogger INFOID:0000000010284256
Heats the heating wire with the power supply from the rear window I
defogger relay to prevent the door mirror from fogging up.
JMLIA2596GB DEF

SYSTEM
SYSTEM
System Description INFOID:0000000010002212
SYSTEM DIAGRAM
ALLIA1379GB
OPERATION DESCRIPTION
• When rear window defogger switch is turned ON while ignition switch is ON, the rear window defogger
switch transmits rear window defogger switch signal to BCM.
• BCM turns rear window defogger relay ON when rear window defogger switch signal is received.
• Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and
operate when rear window defogger relay turns ON.
• Rear window defogger ON is displayed when front air control (manual A/C) or A/C switch (auto A/C)
receives signals.
TIMER FUNCTION
• BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON while ignition switch is ON. It makes rear window defogger and door mirror defogger (with door
mirror defogger) operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same reaction also occurs during timer operation, if the ignition switch
is turned OFF.
INPUT/OUTPUT SIGNAL CHART
Switch Input signal to BCM BCM function Actuator

Rear window defogger and door Rear window defogger
Rear window defogger switch Defogger switch signal
mirror defogger* control Door mirror defogger *
*: With door mirror defogger

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010284246
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Direct Diagnostic Mode Description
Ecu Identification The BCM part number is displayed.
D
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components. E
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM. F
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
G
BCM can perform the following functions.
Direct Diagnostic Mode

H
CAN Diag Support Mntr

Self Diagnostic Result
Ecu Identification
System Sub System I
Configuration
Work support
Data Monitor
Active Test
J
Door lock DOOR LOCK × × × ×

Rear window defogger REAR DEFOGGER × × × K
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
DEF
Exterior lamp HEADLAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × M
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
N
BCM BCM × × × × ×
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × O
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × P
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
REAR DEFOGGER

REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER) INFOID:0000000010284250
DATA MONITOR
Monitor Item [Unit] Description

PUSH SW [On/Off] Indicates condition of push-button ignition switch.
REAR DEF SW [On/Off] Indicates condition of rear window defogger switch.
ACTIVE TEST
Test Item Description

REAR DEFOGGER This test is able to check rear window defogger operation [Off/On].
WORK SUPPORT
Support Item Setting Description

MODE3 Rear defogger turns OFF after 1 minute.
SET R-DEF TIMER MODE2 Rear defogger remains ON until turned OFF.
MODE1* Rear defogger turns OFF after 15 minutes.
* : Initial setting

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010284248
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Direct Diagnostic Mode Description
Ecu Identification The BCM part number is displayed.
D
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components. E
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM. F
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
G
BCM can perform the following functions.
Direct Diagnostic Mode

H
CAN Diag Support Mntr

Self Diagnostic Result
Ecu Identification
System Sub System I
Configuration
Work support
Data Monitor
Active Test
J
Door lock DOOR LOCK × × ×

Rear window defogger REAR DEFOGGER × × × K
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
DEF
Remote keyless entry system MULTI REMOTE ENT ×
Exterior lamp HEADLAMP × ×
Wiper and washer WIPER × × × M
Turn signal and hazard warning lamps FLASHER × ×
Combination switch COMB SW ×
N
BCM BCM × × × × ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × O
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × P
TPMS AIR PRESSURE MONITOR × × × ×
REAR DEFOGGER
REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER) INFOID:0000000010284253
DATA MONITOR
Monitor Item [Unit] Description

REAR DEF SW [On/Off] Indicates condition of rear window defogger switch.
ACTIVE TEST
Test Item Description

REAR DEFOGGER This test is able to check rear window defogger operation [Off/On].
WORK SUPPORT
Support Item Setting Description

MODE3 Rear defogger turns OFF after 1 minute.
SET R-DEF TIMER MODE2 Rear defogger remains ON until turned OFF.
MODE1* Rear defogger turns OFF after 15 minutes.
* : Initial setting

BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
BCM (BODY CONTROL MODULE)
List of ECU Reference INFOID:0000000010002215
B
ECU Reference C
BCS-28, "Reference Value"
BCS-47, "Fail Safe"
BCM (with Intelligent Key system)
BCS-47, "DTC Inspection Priority Chart" D
BCS-48, "DTC Index"
BCS-96, "Reference Value"
E
BCS-107, "Fail Safe"
BCM (without Intelligent Key system)
BCS-107, "DTC Inspection Priority Chart"
BCS-108, "DTC Index" F
DEF

REAR WINDOW DEFOGGER SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM
Wiring Diagram INFOID:0000000010002216
AALWA0762GB

< WIRING DIAGRAM >
DEF
AALIA2107GB

< WIRING DIAGRAM >
AALIA2108GB

< WIRING DIAGRAM >
DEF
AALIA2109GB

< WIRING DIAGRAM >
AALIA2110GB

< WIRING DIAGRAM >
DEF
AALIA2111GB

< WIRING DIAGRAM >
AALIA2238GB

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000010002217
B
OVERALL SEQUENCE
C
DEF
JMKIA0101GB
DETAILED FLOW

1. GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2. CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
- Record DTC and freeze frame data (Print them out with CONSULT.)
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3. CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4. CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5. PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
At this time, always connect CONSULT to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-47, "DTC Inspection Priority Chart" (with Intelligent Key sys-
tem) or BCS-107, "DTC Inspection Priority Chart" (without Intelligent Key system) and determine trouble
diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
simplified check procedure is an effective alternative though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirma-
tion Procedure.
Is DTC detected?
YES >> GO TO 8.
NO >> Refer to GI-41, "Intermittent Incident".
6. PERFORM BASIC INSPECTION
Perform DEF-19, "Work Flow".
>> GO TO 7
7. DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to DEF-6, "System Description" based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptom.

>> GO TO 8.
8. DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE A
Inspect according to Diagnostic Procedure of the system.

NOTE:
B
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
C
YES >> GO TO 9.
NO >> Check voltage of related BCM terminals using CONSULT.
9. REPAIR OR REPLACE THE MALFUNCTIONING PART D
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment. E
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 10. F
10. FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely. G
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear? H
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO >> Inspection End. I
DEF

REAR WINDOW DEFOGGER SWITCH
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
WITH MANUAL A/C
WITH MANUAL A/C : Description INFOID:0000000010002218
• The rear window defogger is operated by pressing the rear window defogger switch ON.
• The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
WITH MANUAL A/C : Component Function Check INFOID:0000000010002219
1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

Check that the indicator lamp of the rear window defogger switch illuminates when rear window defogger
switch is ON.
Is the inspection result normal?
YES >> Rear window defogger switch function is OK.
NO >> Refer to DEF-22, "WITH MANUAL A/C : Diagnosis Procedure".
WITH MANUAL A/C : Diagnosis Procedure INFOID:0000000010002220
Regarding Wiring Diagram information, refer to DEF-12, "Wiring Diagram".
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

With CONSULT
1. Select “REAR DEFOGGER” of “BCM” using CONSULT.
2. Select “REAR DEF SW” in “Data Monitor” mode.
3. Check “REAR DEF SW” indication under the following conditions.
Monitor item Condition Status

Pressed On
REAR DEF SW Rear window defogger switch
Not Pressed Off
YES >> Rear window defogger switch is OK.
NO >> Replace front air control. Refer to HAC-181, "Removal and Installation".
WITH AUTO A/C
WITH AUTO A/C : Description INFOID:0000000010002221
• The rear window defogger is operated by pressing the rear window defogger switch ON.
• The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
WITH AUTO A/C : Component Function Check INFOID:0000000010002222
1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

Check that the indicator lamp of the rear window defogger switch illuminates when rear window defogger
switch is ON.
YES >> Rear window defogger switch function is OK.
NO >> Refer to DEF-22, "WITH MANUAL A/C : Diagnosis Procedure".
WITH AUTO A/C : Diagnosis Procedure INFOID:0000000010002223

A
1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

With CONSULT B
1. Select “REAR DEFOGGER” of “BCM” using CONSULT.
2. Select “REAR DEF SW” in “Data Monitor” mode.
3. Check “REAR DEF SW” indication under the following conditions. C
Monitor item Condition Status

Pressed On D
REAR DEF SW Rear window defogger switch
Not Pressed Off
Is the inspection result normal? E
YES >> Rear window defogger switch is OK.
NO >> Replace A/C switch. Refer to HAC-102, "Removal and Installation".
F
DEF

REAR WINDOW DEFOGGER RELAY
Description INFOID:0000000010002224
Power is supplied to the rear window defogger with BCM control.

Component Function Check INFOID:0000000010002225
1. CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT

Check that an operation noise of rear window defogger relay [located in fuse block (J/B)] can be heard when
turning the rear window defogger switch ON.
YES >> Rear window defogger relay power supply circuit is OK.
NO >> Refer to DEF-24, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000010002226
1. CHECK REAR WINDOW DEFOGGER RELAY GROUND CIRCUIT

1. Turn ignition switch ON.
2. Check voltage between BCM connector and ground.
(+)
Voltage (V)
BCM (–) Condition
(Approx.)
Connector Terminal
Rear window de- ON 0

M18 24 Ground
fogger switch OFF Battery voltage
YES >> Rear window defogger power supply circuit is OK.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and fuse block (J/B).
3. Check continuity between BCM connector and fuse block (J/B) connector.
BCM Fuse block (J/B)

Continuity
Connector Terminal Connector Terminal
M18 24 M44 6P Yes
YES >> GO TO 3.
NO >> Repair or replace harness.
3. CHECK REAR WINDOW DEFOGGER RELAY
Check rear window defogger relay.
Refer to DEF-25, "Component Inspection".
YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".
NO >> Replace rear window defogger relay.

Component Inspection INFOID:0000000010002227
A
1. CHECK REAR WINDOW DEFOGGER RELAY
B
Terminal
Rear window Condition Continuity
C
defogger relay
12V direct current supply between termi-
Yes
3 5 nals 1 and 2.
D
No current supply No
SEF497Y
YES >> Inspection End. E
NO >> Replace rear window defogger relay.
DEF

REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
1. CHECK REAR WINDOW DEFOGGER

Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch
ON.
YES >> Rear window defogger is OK.
1. CHECK FUSES
Check if any of the following fuses in fuse block (J/B) are blown.
COMPONENT PARTS AMPERE FUSE NO.

15A 23
Fuse block (J/B)
15A 24
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2. CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT
2. Check voltage between fuse block (J/B) connector and ground.
(+)
Voltage (V)
Fuse block (J/B) (–) Condition
(Approx.)
Connector Terminal
Rear window de- ON Battery voltage

B29 3T, 5T Ground
fogger switch OFF 0
YES >> GO TO 3.
NO >> Perform rear window defogger relay diagnosis. Refer to DEF-24, "Diagnosis Procedure".
3. CHECK POWER SUPPLY CIRCUIT
2. Check voltage between rear window defogger connector and ground.

(+) A
Voltage (V)
Rear window defogger (–) Condition
(Approx.)
Connector Terminal
B
D510 1 Ground
fogger switch OFF 0
Is the inspection result normal? C
YES >> GO TO 4.
NO >> GO TO 5.
4. CHECK GROUND CIRCUIT D

2. Disconnect rear window defogger.
E
3. Check continuity between rear window defogger connector and ground.
Rear window defogger

Continuity F
Connector Terminal Ground
D525 2 Yes
Is the inspection result normal? G
YES >> GO TO 6.
5. CHECK HARNESS CONTINUITY H

2. Disconnect fuse block (J/B).
I
3. Check continuity between fuse block (J/B) connector and rear window defogger condenser connector.
Fuse block (J/B) Rear window defogger condenser

Continuity J
Connector Terminal Connector Terminal
3T
B29 B6 1 Yes
5T K
YES >> Replace rear window defogger condenser. Refer to DEF-41, "Removal and Installation".
NO >> Replace or repair harness. DEF
6. CHECK FILAMENT
Check filament. M
YES >> Refer to GI-41, "Intermittent Incident". N
NO >> Repair filament. Refer to DEF-39, "Inspection and Repair".
O
1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-39, "Inspection and Repair". P
YES >> Inspection End.
NO >> Repair filament. Refer to DEF-39, "Inspection and Repair".

DRIVER SIDE DOOR MIRROR DEFOGGER
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
1. CHECK DOOR MIRROR DEFOGGER LH

Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch
ON.
YES >> Door mirror defogger is OK.

2. Disconnect door mirror LH.
4. Check voltage between door mirror LH connector and ground.
(+)
Voltage (V)
Door mirror LH (–) Condition
(Approx.)
Connector Terminal

D14 2 Ground
fogger switch OFF 0
YES >> GO TO 2.
2. CHECK GROUND CIRCUIT
2. Check continuity between door mirror LH connector and ground.
Door mirror LH
Continuity
D14 10 Yes
YES >> GO TO 3.
Check door mirror defogger LH.
YES >> GO TO 4.
NO >> Replace door mirror. Refer to MIR-22, "Removal and Installation".

4. CHECK INTERMITTENT INCIDENT A
Check intermittent incident.
Refer to GI-41, "Intermittent Incident".
Is the inspection result normal? B
YES >> Check the following.
• Battery power supply circuit.
• Fuse block (J/B).
C
NO >> Repair or replace the malfunctioning parts.
D
2. Disconnect door mirror LH. E
3. Check continuity between door mirror terminals.
Terminal Continuity F
2 10 Yes
G
NO >> Replace door mirror LH. Refer to MIR-22, "Removal and Installation".
H
DEF

PASSENGER SIDE DOOR MIRROR DEFOGGER
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
1.CHECK DOOR MIRROR DEFOGGER RH

Check that the heating wire of door mirror defogger RH is heated when turning the rear window defogger
switch ON.
YES >> Door mirror defogger RH is OK.

2. Disconnect door mirror RH.
4. Check voltage between door mirror RH connector and ground.
(+)
Voltage (V)
Door mirror RH (–) Condition
(Approx.)
Connector Terminal

D107 2 Ground
fogger switch OFF 0
YES >> GO TO 2.
2. CHECK GROUND CIRCUIT
2. Check continuity between door mirror RH connector and ground.
Door mirror RH
Continuity
D107 10 Yes
YES >> GO TO 3.
3. CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER
Check door mirror defogger RH.
YES >> GO TO 4.
NO >> Replace door mirror RH. Refer to MIR-22, "Removal and Installation".

4. CHECK INTERMITTENT INCIDENT A
Check intermittent incident.
Refer to GI-41, "Intermittent Incident".
Is the inspection result normal? B
YES >> Check the following.
• Battery power supply circuit.
• Fuse block (J/B).
C
D
1. CHECK DOOR MIRROR DEFOGGER RH
2. Disconnect door mirror RH. E
3. Check continuity between door mirror terminals.
Terminal Continuity F
2 10 Yes
G
NO >> Replace door mirror RH. Refer to MIR-22, "Removal and Installation".
H
DEF

DEFOGGER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
DEFOGGER SYSTEM SYMPTOMS
Symptom Table INFOID:0000000010002240
Symptom Reference page

Rear window defoggers and door mirror defoggers* do not operate. Refer to DEF-33, "Diagnosis Procedure".
Rear window defoggers do not operate but both of the door mirror defoggers* operate. Refer to DEF-34, "Diagnosis Procedure".
Both door mirror defoggers* don’t operate but rear window defoggers operate. Refer to DEF-35, "Diagnosis Procedure".
Driver side door mirror defogger* does not operate. Refer to DEF-36, "Diagnosis Procedure".
Passenger side door mirror defogger* does not operate. Refer to DEF-37, "Diagnosis Procedure".
Rear window defogger switch does not light, but rear window defogger operates. Refer to DEF-38, "Diagnosis Procedure".
*:if equipped

REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPER-
ATE.
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT
A
OPERATE.
B

C
1. CHECK REAR WINDOW DEFOGGER SWITCH

D
Check rear window defogger switch.
Refer to DEF-22, "WITH MANUAL A/C : Component Function Check".
E
YES >> GO TO 2.
2. CHECK REAR WINDOW DEFOGGER RELAY F
Refer to DEF-24, "Component Function Check".
Is the inspection result normal? G
YES >> GO TO 3.
3. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT H
Check rear window defogger power supply and ground circuit.
I
YES >> GO TO 4.
J
4. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY
2. Check voltage between fuse block (J/B) connector and ground. K
(+)
Voltage (V) DEF
(Approx.)
Connector Terminal

M44 4P, 5P Ground M
fogger switch OFF 0
YES >> GO TO 5. N
NO >> Replace fuse block (J/B).
5. CHECK BOTH DOOR MIRROR DEFOGGER
O
1. Check door mirror LH. Refer to DEF-28, "Component Function Check".
2. Check door mirror RH. Refer to DEF-30, "Component Function Check".
P

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIR-
ROR DEFOGGER OPERATE.
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR
MIRROR DEFOGGER OPERATE.
1. CHECK REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT

Check rear window defogger power supply and ground circuit.
YES >> Refer to GI-41, "Intermittent Incident".

BOTH DOORS MIRROR DEFOGGER DON’T OPERATE BUT REAR WINDOW
DEFOGGER OPERATES
BOTH DOORS MIRROR DEFOGGER DON’T OPERATE BUT REAR WIN-
A
DOW DEFOGGER OPERATES
B

C
1. CHECK DOOR MIRROR DEFOGGER FUSE

D
Check if the following fuse in fuse block (J/B) is blown.
COMPONENT PARTS AMPERE FUSE NO.

E
Fuse block (J/B) 10A 22
YES >> GO TO 2. F
NO >> Replace the blown fuse after repairing the affected circuit.
2. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch ON. G
2. Check voltage between fuse block (J/B) harness connector and ground.
(+) H
Voltage (V)
(Approx.)
Connector Terminal
I
M44 4P, 5P Ground
fogger switch OFF 0
Is the inspection result normal? J
YES >> GO TO 3.
NO >> Replace fuse block (J/B).
3. CHECK BOTH DOOR MIRROR DEFOGGER K
1. Check door mirror LH. Refer to DEF-28, "Component Function Check".

2. Check door mirror RH. Refer to DEF-30, "Component Function Check". DEF
NO >> Repair or replace the malfunctioning parts. M

DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.

Check door mirror defogger LH.

PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
PASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE.
A
1. CHECK DOOR MIRROR DEFOGGER RH B

Check door mirror defogger RH.
Is the inspection result normal? C
D
DEF

REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WIN-
DOW DEFOGGER OPERATES
1. CHECK REAR WINDOW DEFOGGER SWITCH

Check that the rear window defogger switch is operating normally.
NO >> Refer to DEF-22, "WITH MANUAL A/C : Diagnosis Procedure" or DEF-22, "WITH AUTO A/C :
Diagnosis Procedure".

FILAMENT
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
FILAMENT
Inspection and Repair INFOID:0000000009796646
B
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg- C
ative probe. Then press the foil against the wire with your finger.
SEL122R F
2. Attach probe circuit tester (in Volt range) to middle portion of

each filament. G
SEL263
J
3. If a filament is burned out, circuit tester registers 0 or battery
voltage.
4. To locate burned out point, move probe to left and right along fil- K
ament. Test needle will swing abruptly when probe passes the
point.
DEF
SEL265
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)

FILAMENT
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
PIIA0215E
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
SEL012D
5. Apply a constant stream of hot air directly to the repaired area

for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
SEL013D

CONDENSER
CONDENSER
A
Removal and Installation INFOID:0000000010247854
REMOVAL B
1. Partially lower headlining (rear). Refer to INT-30, "Removal and Installation".
2. Disconnect the harness connectors from the condenser.
C
3. Remove the bolt (A) and the condenser (1).
F
ALLIA1370ZZ
INSTALLATION
Installation is in the reverse order of removal. G
DEF

Defogger: Section

Uploaded by

Copyright:

Available Formats

Defogger: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Defogger: Section

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

PRECAUTIONS ................................................... 3 WIRING DIAGRAM ...................................... 12

Revision: November 2013 DEF-1 2014 Rogue NAM

REAR WINDOW DEFOGGER DOES NOT REMOVAL AND INSTALLATION .............. 39

Revision: November 2013 DEF-2 2014 Rogue NAM

Revision: November 2013 DEF-3 2014 Rogue NAM

A. A/C switch (auto A/C) A. Front air control (manual A/C)

No. Component Description

Revision: November 2013 DEF-4 2014 Rogue NAM

Revision: November 2013 DEF-5 2014 Rogue NAM

INPUT/OUTPUT SIGNAL CHART

Switch Input signal to BCM BCM function Actuator

Revision: November 2013 DEF-6 2014 Rogue NAM

Direct Diagnostic Mode

CAN Diag Support Mntr

System Sub System I

Door lock DOOR LOCK × × × ×

Revision: November 2013 DEF-7 2014 Rogue NAM

Monitor Item [Unit] Description

Test Item Description

Support Item Setting Description

Revision: November 2013 DEF-8 2014 Rogue NAM

Direct Diagnostic Mode

CAN Diag Support Mntr

System Sub System I

Door lock DOOR LOCK × × ×

Monitor Item [Unit] Description

Test Item Description

Support Item Setting Description

Revision: November 2013 DEF-10 2014 Rogue NAM

Revision: November 2013 DEF-11 2014 Rogue NAM

Revision: November 2013 DEF-12 2014 Rogue NAM

Revision: November 2013 DEF-13 2014 Rogue NAM

Revision: November 2013 DEF-14 2014 Rogue NAM

Revision: November 2013 DEF-15 2014 Rogue NAM

Revision: November 2013 DEF-16 2014 Rogue NAM

Revision: November 2013 DEF-17 2014 Rogue NAM

Revision: November 2013 DEF-18 2014 Rogue NAM

Revision: November 2013 DEF-19 2014 Rogue NAM

Revision: November 2013 DEF-20 2014 Rogue NAM

Inspect according to Diagnostic Procedure of the system.

Revision: November 2013 DEF-21 2014 Rogue NAM

1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

Regarding Wiring Diagram information, refer to DEF-12, "Wiring Diagram".

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

Monitor item Condition Status

1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

Revision: November 2013 DEF-22 2014 Rogue NAM

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

Monitor item Condition Status

Revision: November 2013 DEF-23 2014 Rogue NAM

Power is supplied to the rear window defogger with BCM control.

1. CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT

Regarding Wiring Diagram information, refer to DEF-12, "Wiring Diagram".

1. CHECK REAR WINDOW DEFOGGER RELAY GROUND CIRCUIT

Rear window de- ON 0

BCM Fuse block (J/B)

Revision: November 2013 DEF-24 2014 Rogue NAM