Wiper & Washer: Section
Wiper & Washer: Section
SECTION
WIPER & WASHER
WW B
E
CONTENTS
BASIC INSPECTION .................................... 3 FRONT WIPER MOTOR LO CIRCUIT .............. 20 F
Component Function Check ....................................20
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 Diagnosis Procedure ...............................................20
Work Flow ................................................................. 3 G
FRONT WIPER MOTOR HI CIRCUIT ............... 22
FUNCTION DIAGNOSIS ............................... 5 Component Function Check ....................................22
Diagnosis Procedure ...............................................22
FRONT WIPER AND WASHER SYSTEM .......... 5 H
System Diagram ........................................................ 5 FRONT WIPER AUTO STOP SIGNAL CIR-
System Description ................................................... 5 CUIT .................................................................. 24
Component Parts Location ........................................ 8 Component Function Check ....................................24 I
Component Description ............................................ 8 Diagnosis Procedure ...............................................24
DIAGNOSIS SYSTEM (BCM) ............................. 9 FRONT WIPER MOTOR GROUND CIRCUIT ... 26
Diagnosis Procedure ...............................................26 J
COMMON ITEM ........................................................... 9
COMMON ITEM : CONSULT-III Function (BCM - WASHER SWITCH ............................................ 27
COMMON ITEM) ....................................................... 9 Description ...............................................................27 K
Component Inspection .............................................27
WIPER ....................................................................... 10
WIPER : CONSULT-III Function (BCM - WIPER).... 10 FRONT WIPER AND WASHER SYSTEM ........ 28
Wiring Diagram - FRONT WIPER AND WASHER WW
DIAGNOSIS SYSTEM (IPDM E/R) .....................12
SYSTEM - ................................................................28
Diagnosis Description ............................................. 12
CONSULT-III Function (IPDM E/R) ......................... 14 ECU DIAGNOSIS ......................................... 31 M
COMPONENT DIAGNOSIS ......................... 17 BCM (BODY CONTROL MODULE) ................. 31
WIPER AND WASHER FUSE ............................17 Reference Value ......................................................31
Wiring Diagram - BCM - ..........................................54 N
Description .............................................................. 17
Fail-safe ...................................................................59
Diagnosis Procedure ............................................... 17
DTC Inspection Priority Chart ...............................62
POWER SUPPLY AND GROUND CIRCUIT ......18 DTC Index ...............................................................63 O
BCM (BODY CONTROL MODULE) .......................... 18 IPDM E/R (INTELLIGENT POWER DISTRI-
BCM (BODY CONTROL MODULE) : Diagnosis BUTION MODULE ENGINE ROOM) ................ 66
Procedure ................................................................ 18 Reference Value ......................................................66 P
Wiring Diagram - IPDM E/R - ..................................73
IPDM E/R (INTELLIGENT POWER DISTRIBU- Fail-safe ...................................................................76
TION MODULE ENGINE ROOM) .............................. 18 DTC Index ...............................................................78
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) : Diagnosis Pro- SYMPTOM DIAGNOSIS .............................. 79
cedure ..................................................................... 18
FRONT WIPER DOES NOT OPERATE ............ 82 FRONT WASHER NOZZLE AND TUBE ........... 89
Description .............................................................. 82 Hydraulic Layout ..................................................... 89
Diagnosis Procedure .............................................. 82 Removal and Installation ......................................... 89
Inspection and Adjustment ...................................... 89
PRECAUTION ............................................. 84
FRONT WIPER ARM ......................................... 91
PRECAUTIONS ................................................. 84 Exploded View ........................................................ 91
Precaution for Supplemental Restraint System Removal and Installation ......................................... 91
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Adjustment .............................................................. 91
SIONER" ................................................................. 84
Precaution for Battery Service ................................ 84 WIPER BLADE .................................................. 93
Precaution for Procedure without Cowl Top Cover... 84 Exploded View ........................................................ 93
Removal and Installation ......................................... 93
PREPARATION ........................................... 85 Replacement ........................................................... 93
OVERALL SEQUENCE
C
WW
P
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7.
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.
JPLIA1261GB
G
System Description INFOID:0000000004468131
OUTLINE H
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function I
• Front wiper control function
Control by IPDM E/R
J
• Front wiper control function
• Relay control function
Combination meter indicates low washer fluid warning judged with the signal from the washer level switch. For
details of low washer fluid warning, refer to MWI-26, "INFORMATION DISPLAY : System Description". K
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each WW
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation. M
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition. N
JPLIA1256GB
NOTE:
Factory setting of the front wiper intermittent operation is the operation without vehicle speed. Front wiper
intermittent operation can be set to the operation with vehicle speed by CONSULT-III. Refer to WW-10,
"WIPER : CONSULT-III Function (BCM - WIPER)".
Front wiper intermittent operation with vehicle speed
• BCM calculates the intermittent operation delay interval from the following.
- Vehicle speed signal (received from the combination meter with CAN communication)
- Wiper intermittent dial position
Unit: Second
Intermittent operation delay Interval
Intermittent
Wiper intermittent Vehicle speed
operation
dial position
interval 0 – 5 km/h 5 – 35 km/h 35 – 65 km/h 65 km/h (40.4 MPH)
(0 – 3.1 MPH) (3.1 – 21.7 MPH) (21.7 – 40.4 MPH)* or more
1 0.8 0.6 0.4 0.24
Short
2 ↑ 4 3 2 1.2
3 10 7.5 5 3
4 16 12 8 4.8
5 24 18 12 7.2
6 ↓ 32 24 16 9.6
Long
7 42 31.5 21 12.6
JPLIA0410GB
NOTE: F
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER G
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times
H
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON I
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
• The washer pump is grounded through the combination switch with the front washer switch ON.
J
FRONT WIPER FAIL-SAFE OPERATION
IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
PCS-29, "Fail-safe".
K
WW
JPLIA1581ZZ
Part Description
• Judges each switch status by the combination switch reading function.
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
• Controls the integrated relay according to the request (with CAN communication) from BCM.
IPDM E/R
• Performs the auto stop control of the front wiper.
Combination switch
Refer to BCS-9, "System Diagram".
(Wiper & washer switch)
Combination meter Transmits the vehicle speed signal to BCM with CAN communication.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × × K
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
WW
— AIR CONDITONER*
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
M
Combination switch COMB SW ×
Body control system BCM ×
IVIS - NATS IMMU × × N
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk lid open TRUNK × ×
O
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER × × P
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
*: This item is displayed, but is not used.
WIPER
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000004468139
WORK SUPPORT
DATA MONITOR
Monitor Item A
Description
[Unit]
PUSH SW
The switch status input from push-button ignition switch.
[Off/On]
B
VEH SPEED 1
The value of the vehicle speed signal received from combination meter with CAN communication.
[km/h]
FR WIPER HI C
[Off/On]
FR WIPER LOW
[Off/On]
Each switch status that BCM judges from the combination switch reading function. D
FR WASHER SW
[Off/On]
FR WIPER INT
E
[Off/On]
FR WIPER STOP
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
[Off/On]
F
INT VOLUME
Each switch status that BCM judges from the combination switch reading function.
[1 − 7]
ACTIVE TEST G
WW
Operation
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• License plate lamps
3 10 seconds
• Side maker lamps
• Tail lamps
4 Headlamps LO for 10 seconds → HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
JPMIA1312GB F
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated. G
K
• Unified meter and A/C amp.
signal input circuit
• CAN communication signal
YES
between unified meter and WW
A/C amp. and ECM
Perform auto active test. • CAN communication signal
A/C compressor does not operate Does the magnet clutch oper- between ECM and IPDM E/
ate? R M
• Magnet clutch
• Harness or connector be-
NO tween IPDM E/R and mag- N
net clutch
• IPDM E/R
• Harness or connector be-
tween IPDM E/R and oil
O
YES pressure switch
• Oil pressure switch
• IPDM E/R P
Perform auto active test.
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal
lamp blink? between IPDM E/R and
BCM
NO • CAN communication signal
between BCM and unified
meter and A/C amp.
• Combination meter
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
Fuse list
Unit Location No. Capacity
C
Front wiper motor IPDM E/R 60 30 A
Washer pump IPDM E/R 47 10 A
D
Diagnosis Procedure INFOID:0000000004468143
1.CHECK FUSES
E
Check that the following fuses are not fusing.
WW
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M118 1
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure INFOID:0000000004715366
Terminals
(+) Voltage F
(−)
IPDM E/R (Approx.)
Connector Terminal
Ground G
E4 1 Battery voltage
Is the measurement value normal?
YES >> GO TO 3. H
NO >> Repair the harness or connector.
3.CHECK GROUND CIRCUIT
I
Check continuity between IPDM E/R harness connectors and the ground.
IPDM E/R
Continuity J
Connector Terminal
Ground
E5 12
Existed
E6 41 K
Does continuity exist?
YES >> INSPECTION END
NO >> Repair the harness or connector. WW
Terminals
Test item
(+) (−)
Voltage (Approx.)
IPDM E/R
FRONT WIPER
Connector Terminal
Ground
Lo Battery voltage
E5 4
Off 0V
Is the measurement value normal?
YES >> GO TO 2.
NO >> Replace IPDM E/R.
2.CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
IPDM E/R A
Continuity
Connector Terminal Ground
E5 4 Not existed
B
Does continuity exist?
YES >> Repair the harness or connector.
NO >> Replace front wiper motor. C
WW
Terminals
Test item
(+) (−)
Voltage (Approx.)
IPDM E/R
FRONT WIPER
Connector Terminal
Ground
Hi Battery voltage
E5 5
Off 0V
Is the measurement value normal?
YES >> GO TO 2.
NO >> Replace IPDM E/R.
2.CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
IPDM E/R A
Continuity
Connector Terminal Ground
E5 5 Not existed
B
Does continuity exist?
YES >> Repair the harness or connector.
NO >> Replace front wiper motor. C
WW
Terminals
(+) (−)
Voltage (Approx.)
IPDM E/R
Connector Terminal Ground
E5 16 Battery voltage
Is the measurement value normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK FRONT WIPER MOTOR (AUTO STOP) SHORT CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and ground.
IPDM E/R
Continuity
Connector Terminal Ground
E5 16 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> Replace IPDM E/R.
3.CHECK FRONT WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
WW
JPLIA0310ZZ
E
Component Inspection INFOID:0000000004468154
Combination switch
Condition Continuity H
Terminal
1 6 Front washer switch ON Existed
Does continuity exist? I
YES >> Wiper and washer switch is normal.
NO >> Replace combination switch (Wiper and washer switch).
J
WW
JCLWA2650GB
WW
JCLWA2651GB
JCLWA2652GB
JPMIA0062ZZ
PHYSICAL VALUES
N
JSNIA0010GB
PKID0926E
6.5 V
Turn signal switch OFF 0V
PKID0926E
6.5 V
20 Ignition switch
Ground Turn signal RH (Rear) Output
(V) ON Turn signal switch RH
PKID0926E
6.5 V
OPEN
(Back door opener actua- 12 V
23 tor is activated)
Ground Back door open Output Back door
(L) Other than OPEN
(Back door opener actua- 0V
tor is not activated)
24*1 OFF 0V
Ground Rear fog lamp Output Rear fog lamp
(O) ON 12 V
Turn signal switch OFF 0V
25 Ignition switch
Ground Turn signal LH (Rear) Output
(LG) ON Turn signal switch LH
PKID0926E
6.5 V
30 Luggage room ON 0V
Ground Luggage room lamp Output
(R) lamp OFF 12 V
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
JMKIA0062GB
I
35 Luggage room anten- Ignition switch
Ground Output
(R) na (+) OFF
J
JMKIA0063GB
WW
M
When Intelligent Key is in
the antenna detection
area
N
When the back JMKIA0062GB
door request
38 Rear bumper anten-
Ground Output switch is oper-
(B) na (−)
ated with igni-
O
tion switch
OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB
JMKIA0063GB
JPMIA0016GB
1.0 V
JPMIA0011GB
11.8 V
ON (Door open) 0V
67
Ground
Back door opener
Input
Back door C
(GR) switch opener switch Not pressed
D
JPMIA0011GB
11.8 V
JMKIA0062GB
G
72 Room antenna (−) Ignition switch
Ground Output
(L) (Center console) OFF
H
When Intelligent Key is not
in the passenger compart-
ment
I
JMKIA0063GB
WW
JMKIA0062GB
JMKIA0063GB
O
JMKIA0063GB
JMKIA0063GB
JMKIA0063GB
During waiting
K
JMKIA0064GB
Remote keyless entry WW
83 Input/
Ground receiver communica-
(GR) Output
tion
M
When operating either button on the Intelli-
gent Key
N
JMKIA0065GB
JPMIA0041GB
1.4 V
JPMIA0038GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0036GB
JPMIA0037GB
I
1.3 V
J
Any of the conditions be-
low with all switches OFF
• Wiper intermittent dial 1
K
• Wiper intermittent dial 2
• Wiper intermittent dial 3
JPMIA0040GB
1.3 V WW
Push-button ig- Pressed 0V
89 Push-button ignition
Ground Input nition switch
(BR) switch (Push switch) Not pressed Battery voltage
(push switch) M
90 Input/
Ground CAN-L — —
(P) Output
91
Ground CAN-H
Input/
— —
N
(L) Output
OFF 0V
O
JPMIA0015GB
6.5 V
ON 12 V
95 OFF 0V
Ground ACC relay control Output Ignition switch
(O) ACC or ON 12 V
Control device (De-
96*2 Ground tention switch) power Output — 12 V
(Y) supply
Passenger
100 Passenger door re-
Ground Input door request
(GR) quest switch OFF (Not pressed)
switch
JPMIA0016GB
1.0 V
ON (Pressed) 0V
JPMIA0016GB
1.0 V
JPMIA0041GB
1.4 V D
F
JPMIA0037GB
1.3 V
G
Combination
107 Combination switch switch
H
Ground Input Turn signal switch RH
(LG) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
JPMIA0038GB
1.3 V WW
N
JPMIA0039GB
1.3 V
O
JPMIA0041GB
1.4 V
JPMIA0038GB
JPMIA0036GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
F
JPMIA0037GB
1.3 V
G
Combination
109 Combination switch switch
H
Ground Input Lighting switch 2ND
(Y) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
JPMIA0038GB
1.3 V WW
N
JPMIA0040GB
1.3 V
ON 0V O
P
110
Ground Hazard switch Input Hazard switch
(P) OFF
JPMIA0012GB
1.1 V
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(Y) communication Output
JMKIA0066GB
LOCK status
(Unlock sensor switch
Driver side door lock OFF)
119
Ground assembly (Unlock Input Driver door
(SB)
sensor)
JPMIA0012GB
1.1 V
UNLOCK status
(Unlock switch sensor 0V
ON)
When the Intelligent Key is inserted into key
12 V
121 slot
Ground Key slot switch Input
(R) When the Intelligent Key is not inserted into
0V
key slot
JPMIA0011GB
11.8 V D
ON (Door open) 0V
1.1 V G
Rear window defogger
0V
switch ON
H
I
132 Power window switch Input/ Ignition switch ON
Ground
(Y) communication Output
J
JPMIA0013GB
10.2 V
Ignition switch OFF or ACC 12 V
K
ON (Tail lamps OFF) 9.5 V
NOTE:
The pulse width of this wave is
varied by the illumination bright-
WW
ening/dimming level.
Push-button ig-
133 Push-button ignition
(G)
Ground
switch illumination
Output nition switch il- ON (Tail lamps ON) M
lumination
N
JPMIA0159GB
OFF 0V
O
134 LOCK indicator OFF Battery voltage
Ground LOCK indicator lamp Output
(GR) lamp ON 0V
137 Receiver and sensor P
Ground Input Ignition switch ON 0V
(P) ground
Standby state
OCC3880D
JPMIA0014GB
11.3 V
OFF 12 V
All switches OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(O) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switches OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
143 Combination switch Combination Any of the conditions be-
Ground Output
(P) OUTPUT 1 switch low with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3
• Wiper intermittent dial 6 JPMIA0032GB
• Wiper intermittent dial 7 10.7 V
10.7 V
All switches OFF 0V
E
Front wiper switch INT
Front wiper switch LO
Combination F
145 Combination switch switch Lighting switch AUTO
Ground Output
(L) OUTPUT 3 (Wiper intermit-
tent dial 4)
G
Rear fog lamp switch ON
JPMIA0034GB
10.7 V
H
All switches OFF 0V
Lighting switch 2ND
Lighting switch PASS I
Combination
146 Combination switch switch
Ground Output
(SB) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH J
JPMIA0035GB
10.7 V
K
149 Tire pressure warning
Ground Input — 12 V
(W) check switch
WW
JPMIA0011GB
11.8 V N
ON (Door open) 0V
JCMWA3235GB
WW
JCMWA3236GB
JCMWA3237GB
WW
JCMWA3238GB
JCMWA3239GB
WW
JCMWA3240GB
P
Fail-safe INFOID:0000000004715379
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3 • B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4 • B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E8: CLUTCH SW
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
NOTE:
The details of time display are as follows.
J
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-17, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". K
WW
JSMIA0001ZZ
PHYSICAL VALUES
6*1 Ground
Daytime running light
Input Ignition switch OFF Battery voltage
(R) relay
Ignition switch ON G
JPMIA0001GB H
6.3 V
I
40% is set on “ACTIVE TEST”, “ALTERNA-
76 Power generation com-
Ground Output TOR DUTY” of “ENGINE”
(Y) mand signal J
JPMIA0002GB
3.8 V
K
WW
80% is set on “ACTIVE TEST”, “ALTERNA-
TOR DUTY” of “ENGINE”
M
JPMIA0003GB
1.4 V
• Approximately 1 second after turning the N
ignition switch ON 0 - 1.0 V
77 • Engine running
Ground Fuel pump relay control Output
(R)
Approximately 1 second or more after turn-
Battery voltage O
ing the ignition switch ON
80
Ground Starter motor Output At engine cranking Battery voltage
(W)
P
Ignition switch Lighting switch OFF 0V
83 ON Lighting switch 2ND
Ground Headlamp LO (RH) Output
(R) Battery voltage
Daytime running light system activated*1
WW
JCMWA3244GB
P
JCMWA3245GB
WW
JCMWA3246GB
JCMWA3247GB
Fail-safe INFOID:0000000004715369
Ignition switch Front wiper switch Front wiper stop position signal
The front wiper stop position signal (stop
OFF
position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does
ON
not change for 10 seconds.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index INFOID:0000000004715370
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now.
- The number increases like 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF →
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×: Applicable
CONSULT display Fail-safe Refer to
No DTC is detected.
further testing — —
may be required.
U1000: CAN COMM CIRCUIT × PCS-15
B2098: IGN RELAY ON × PCS-16
B2099: IGN RELAY OFF — PCS-17
B2108: STRG LCK RELAY ON — SEC-100
B2109: STRG LCK RELAY OFF — SEC-102
B210A: STRG LCK STATE SW — SEC-103
B210B: START CONT RLY ON — SEC-107
B210C: START CONT RLY OFF — SEC-108
B210D: STARTER RELAY ON — SEC-109
B210E: STARTER RELAY OFF — SEC-110
B210F: INTRLCK/PNP SW ON — SEC-112
B2110: INTRLCK/PNP SW OFF — SEC-114
WW
The front wiper does not operate under any operation conditions.
Diagnosis Procedure INFOID:0000000004468177
Terminals A
Test item
(+) (−)
Voltage (Approx.)
IPDM E/R
FRONT WIPER B
Connector Terminal
Lo Battery voltage
4 Ground
Off 0V C
E5
Hi Battery voltage
5
Off 0V
D
Is the measurement value normal?
YES >> Replace front wiper motor.
NO >> Replace IPDM E/R. E
5.CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R data monitor item. F
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the status of “FR WIP REQ”.
G
Monitor item Condition Monitor status
On Hi
Front wiper switch HI H
Off Stop
FR WIP REQ
On Low
Front wiper switch LO
Off Stop I
Is the status of item normal?
YES >> Replace IPDM E/R.
NO >> GO TO 6. J
6.CHECK COMBINATION SWITCH
Perform the inspection of the combination switch. Refer to BCS-82, "Symptom Table".
K
Is combination switch normal?
YES >> Replace BCM. Refer to BCS-84, "Exploded View".
NO >> Repair or replace the applicable parts. WW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Precaution for Battery Service INFOID:0000000004770270
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precaution for Procedure without Cowl Top Cover INFOID:0000000004468179
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
PIIB3706J
WW
JPLIA1570ZZ
REMOVAL
1. Remove the clip (A).
: Vehicle front
2. Pull out the washer tank inlet (1) from the washer tank.
3. Remove the fender protector RH (front). Refer to EXT-23,
"FENDER PROTECTOR : Exploded View".
4. Disconnect the washer pump connector.
5. Disconnect the washer level switch connector.
6. Disconnect the front washer tube. JPLIA1571ZZ
7. Remove the washer tank mounting bolts.
8. Remove the washer tank from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Add water up to the top of the washer tank inlet after installing. Check that there is no leakage.
JPLIA1572ZZ
REMOVAL I
1. Remove the fender protector RH (front). Refer to EXT-23, "FENDER PROTECTOR : Exploded View".
2. Disconnect the washer pump connector.
J
3. Disconnect the front washer tube.
4. Remove the washer pump from the washer tank.
5. Remove the packing from the washer tank. K
INSTALLATION
Install in the reverse order of removal.
CAUTION: WW
Never twist the packing when installing the washer pump.
The washer level switch must be replaced together with the washer tank as an assembly. Refer to WW-86,
"Removal and Installation".
G
JPLIA1573ZZ
I
REMOVAL
1. Open the hood.
J
2. Remove the front washer nozzle in numerical order shown in the
figure.
K
: Vehicle front
3. Disconnect the front washer tube from the front washer nozzle.
WW
M
JPLIA1574ZZ
INSTALLATION
1. Connect the front washer tube into the front washer nozzle. N
2. Install the front washer nozzle to the hood.
3. Adjust the front washer nozzle spray position. Refer to WW-89, "Inspection and Adjustment".
CAUTION: O
The spray positions differ. Check that left and right nozzles are installed correctly.
Inspection and Adjustment INFOID:0000000004468187
P
INSPECTION
Washer Nozzle Inspection
JPLIA1575ZZ
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
JPLIA1576ZZ
Unit: mm (in)
Passenger side Driver side
A B C D E F G H
X 445 (17.52) 69 (2.72) 181 (7.13) 366 (14.41) 68 (2.68) 458 (18.03) 367 (14.45) 180 (7.09)
Y 493 (19.41) 594 (23.39) 104 (4.09) 87 (3.43) 594 (23.39) 555 (21.85) 90 (3.54) 108 (4.25)
Check that washer fluid is splayed on 80% or more the splay area ( ) when spraying washer fluid. If the
spray area deviates from the specification, adjust the washer nozzle.
CAUTION:
• Use washer nozzle adjuster* (A) for nozzle adjustment.
• Never use needle or small pin.
*: Washer nozzle adjuster is included with shipment of nozzle.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA1626ZZ
G
JPLIA1578GB
1. Front wiper blade (RH) 2. Front wiper arm (RH) 3. Front wiper blade (LH)
4. Front wiper arm (LH) 5. Front wiper arm cap
H
Refer to GI-4, "Components" for symbols in the figure.
REMOVAL
1. Operate the front wiper to move it to the auto stop position. J
2. Open the hood.
3. Remove the front wiper arm caps.
K
4. Remove the front wiper arm mounting nuts.
5. Raise front wiper arm, and remove front wiper arm from the vehicle.
INSTALLATION WW
1. Clean front wiper arm mount as shown in the figure to prevent
nuts from being loosened.
2. Operate the front wiper motor to move the front wiper to the auto M
stop position.
3. Adjust the front wiper blade position. Refer to WW-91, "Adjust-
ment". N
4. Install the front wiper arm by tightening the mounting nuts.
5. Inject the washer fluid.
6. Operate the front wiper to move it to the auto stop position. O
7. Check that the front wiper blades stop at the specified position. ELH0717D
JPLIA0082ZZ
G
JPLIA1587ZZ
I
REMOVAL
Remove the wiper blade from the wiper arm.
INSTALLATION J
Install the front wiper blade to the wiper arm.
Replacement INFOID:0000000004703531
K
1. Hold the rip of old wiper refill (1) at the rear end of the wiper
blade with long-nose pliers, and pull out the wiper refill to the
WW
direction (A).
JPLIA1583ZZ
O
2. Insert the tip of new wiper refill (1) into the rear end of wiper
blade. Slide the wiper refill to the direction (A) while pressing the
wiper refill onto the wiper blade rear end.
NOTE: P
• Insert the wiper refill to be held securely by tab (B) of wiper
blade.
• After the wiper refill is fully inserted, remove the holder* (2).
*: Attached to service parts.
JPLIA1584ZZ
JPLIA1586ZZ
REMOVAL B
JPLIA1625GB
H
1. Front wiper drive assembly
Refer to GI-4, "Components" for symbols in the figure.
DISASSEMBLY I
WW
JPLIA1580ZZ
O
1. Front wiper linkage 1 2. Shaft seal 3. Front wiper motor
4. Front wiper frame 5. Front wiper linkage 2
: Multi−purpose grease or an equivalent.
P
REMOVAL
1. Remove the front wiper arm. Refer to WW-91, "Exploded View".
2. Remove the front tower bar and cowl top cover. Refer to EXT-20, "Exploded View".
DISASSEMBLY
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when removing the front wiper
linkage.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position.
3. Disconnect the front wiper motor connector.
4. Install the front wiper motor to the front wiper frame.
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply Multi−purpose grease or an equivalent if necessary.
WW