Wiper & Washer: Section

DRIVER CONTROLS
WW
A
B
SECTION
WIPER & WASHER C
E
CONTENTS
PRECAUTION ............................................... 3 WIPER ........................................................................14 F
WIPER : CONSULT Function (BCM - WIPER) .......14
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System DIAGNOSIS SYSTEM (IPDM E/R) (WITH IN-
G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- TELLIGENT KEY SYSTEM) ............................. 15
SIONER" ................................................................... 3 Diagnosis Description ..............................................15
Precaution for Procedure without Cowl Top Cover...... 3 CONSULT Function (IPDM E/R) .............................16
H
Precaution for Work .................................................. 3
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT
PREPARATION ............................................ 5 INTELLIGENT KEY SYSTEM) .......................... 19
Diagnosis Description ..............................................19 I
PREPARATION ................................................... 5 CONSULT Function (IPDM E/R) .............................20
Special Service Tools ................................................ 5
ECU DIAGNOSIS INFORMATION .............. 23
SYSTEM DESCRIPTION .............................. 6 J
BCM, IPDM E/R ................................................. 23
FRONT WIPER AND WASHER SYSTEM .......... 6 List of ECU Reference .............................................23
Component Parts Location ........................................ 6 K
Component Description ............................................ 7 WIRING DIAGRAM ...................................... 24
SYSTEM .............................................................. 8 WIPER AND WASHER SYSTEM ..................... 24
System Diagram ........................................................ 8 Wiring Diagram - With Intelligent Key ......................24 WW
System Description ................................................... 8 Wiring Diagram - Without Intelligent Key .................30
Fail-Safe .................................................................. 10
BASIC INSPECTION ................................... 35 M
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) .........................................11 DIAGNOSIS AND REPAIR WORKFLOW ........ 35
Work Flow ................................................................35
COMMON ITEM ......................................................... 11 N
COMMON ITEM : CONSULT Function (BCM - DTC/CIRCUIT DIAGNOSIS ......................... 37
COMMON ITEM) ..................................................... 11
WIPER AND WASHER FUSE ........................... 37
WIPER ....................................................................... 12 Description ...............................................................37 O
WIPER : CONSULT Function (BCM - WIPER) ....... 12 Diagnosis Procedure ...............................................37
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- FRONT WIPER MOTOR LO CIRCUIT .............. 38 P
TELLIGENT KEY SYSTEM) ...............................13 Component Function Check ....................................38
Diagnosis Procedure ...............................................38
COMMON ITEM ......................................................... 13
COMMON ITEM : CONSULT Function (BCM - FRONT WIPER MOTOR HI CIRCUIT ............... 40
COMMON ITEM) ..................................................... 13 Component Function Check ....................................40
Diagnosis Procedure ...............................................40
Revision: December 2015 WW-1 2016 Sentra NAM

FRONT WIPER AUTO STOP SIGNAL CIR- Removal and Installation ......................................... 55
CUIT ................................................................... 42
Component Function Check ................................... 42
WASHER NOZZLE & TUBE ............................. 56
Exploded View ........................................................ 56
Diagnosis Procedure .............................................. 42
WASHER NOZZLE .................................................... 56
FRONT WIPER MOTOR GROUND CIRCUIT ... 43
WASHER NOZZLE : Removal and Installation ....... 56
WASHER NOZZLE : Adjustment ............................ 57
WASHER MOTOR CIRCUIT ............................. 44 WASHER TUBE ........................................................ 57
WASHER TUBE : Removal and Installation ........... 58
WASHER SWITCH ............................................ 46 FRONT WIPER ARM ......................................... 59
Description .............................................................. 46
Exploded View ........................................................ 59
Component Inspection ............................................ 46
Removal and Installation ......................................... 59
SYMPTOM DIAGNOSIS ............................. 47 WIPER BLADE .................................................. 60
WIPER AND WASHER SYSTEM SYMPTOMS WIPER BLADE .......................................................... 60
... 47 WIPER BLADE : Removal and Installation ............. 60
Symptom Table ...................................................... 47
WIPER BLADE REFILL ............................................ 60
FRONT WIPER DOES NOT OPERATE ............ 50 WIPER BLADE REFILL : Removal and Installation
Description .............................................................. 50 ... 60
FRONT WIPER DRIVE ASSEMBLY ................. 64
NORMAL OPERATING CONDITION ................ 52 Exploded View ........................................................ 64
Description .............................................................. 52 Removal and Installation ......................................... 64
REMOVAL AND INSTALLATION ............... 53 WIPER AND WASHER SWITCH ...................... 65

Removal and Installation ......................................... 65
WASHER TANK ................................................ 53
Exploded View ........................................................ 53 SERVICE DATA AND SPECIFICATIONS
Removal and Installation ........................................ 53 (SDS) .......................................................... 66
WASHER PUMP ................................................ 54 SERVICE DATA AND SPECIFICATIONS
Removal and Installation ........................................ 54 (SDS) ................................................................. 66
WASHER LEVEL SWITCH ................................ 55 Specifications .......................................................... 66

PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000013480839
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, it is recommended that all mainte-
nance and repair be performed by an authorized NISSAN/INFINITI dealer. E
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see the SR section.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the H
Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery or batteries, and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover INFOID:0000000012782936
J
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
K
WW
M
PIIB3706J
Precaution for Work INFOID:0000000012782937

N
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component O
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip. P
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
PRECAUTIONS
< PRECAUTION >
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.

PREPARATION
< PREPARATION >
PREPARATION A
PREPARATION
Special Service Tools INFOID:0000000012782938
B
The actual shape of the tools may differ from those illustrated here.
Tool number Description
(TechMate No.) C
Tool name
— Removing trim components
(J-46534) D
Trim Tool Set
AWJIA0483ZZ
WW

FRONT WIPER AND WASHER SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
Component Parts Location INFOID:0000000012782939
AWLIA2585ZZ
1. BCM (view under instrument panel, 2. Combination meter 3. IPDM E/R (view with air inlet duct
left side of vehicle) removed)
4. Combination switch (wiper and 5. Front wiper motor (with wiper cowl 6. Front washer motor (with front
washer switch) cover removed) bumper removed)

Component Description INFOID:0000000012782940
Part Description
Combination meter Transmits the vehicle speed signal to BCM with CAN communication. B
• Judges the switch status by the combination switch reading function.
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high
relay ON to IPDM E/R. C
• Controls the integrated relay according to the request (with CAN communication)
IPDM E/R from BCM.
• Performs the auto stop control of the front wiper.
D
• Provides input for wiper and washer control to the BCM.
Combination switch • Refer to BCS-9, "COMBINATION SWITCH READING SYSTEM : System Descrip-
(Wiper and washer switch) tion" (with Intelligent Key system) or BCS-85, "COMBINATION SWITCH READING
SYSTEM : System Description" (without Intelligent Key system). E
Front washer motor Washer fluid is sprayed according to combination switch signal.
• IPDM E/R controls front wiper operation.
Front wiper motor F
• Front wiper stop position is transmitted to IPDM E/R.
WW

SYSTEM
SYSTEM
System Diagram INFOID:0000000012782941
ABLIA2794GB
System Description INFOID:0000000012782942
FRONT WIPER CONTROL (BASIC)

1. BCM detects the combination switch position by the combination switch reading function.
2. BCM transmits the front wiper request signal to the IPDM E/R using CAN communication.
3. IPDM E/R controls the integrated front wiper relay and front wiper high relay based on the status of the
front wiper request signal.
4. IPDM E/R provides power to operate the front wiper motor.
LOW SPEED OPERATION
1. Ignition switch ON.
2. Front wiper switch in LO or MIST position.
3. BCM reads the combination switch position and transmits the front wiper request signal (LO) to IPDM E/R
using CAN communication.
4. IPDM E/R turns ON the front wiper relay.
HIGH SPEED OPERATION
2. Front wiper switch in HI.
3. BCM reads the combination switch position and transmits the front wiper request signal (HI) to IPDM E/R
4. IPDM E/R turns ON the front wiper relay and the front wiper high relay.
INTERMITTENT OPERATION
2. Front wiper switch INT.
3. BCM reads the combination switch position. BCM calculates the delay interval based on the table below
and then transmits the front wiper request signal (INT) to IPDM E/R using CAN communication.
4. IPDM E/R turns ON the front wiper relay only once.
5. BCM detects stop position of the front wiper motor based on the front wiper stop position signal received
from the IPDM E/R.
6. BCM transmits the front wiper request signal (INT) again after the delay interval.

SYSTEM
C
JPLIA0094GB
D
Intermittent switch position Length of delay Delay interval (s)
7 0.4
6 1 E
Short
5 2
↑
4 3
↓
F
3 5
Long
2 10
1 16 G
AUTO STOP OPERATION

1. Front wiper switch is turned OFF. H
2. BCM monitors wiper switch position by combination switch reading position function.
3. BCM stops transmitting the front wiper request signal to the IPDM E/R.
4. IPDM E/R detects the front wiper auto stop signal from the position of the front wiper motor (stop position/
except stop position). I
5. When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front
wiper motor returns to the stop position.
6. IPDM E/R turns the front wiper relay OFF when the front wiper motor has reached the stop position. J
WW
JPLIA0095GB
O
MIST OPERATION
2. Front washer switch in OFF position. P
3. Front wiper switch in MIST position.
6. The front wiper operates once after the front washer operation.
WIPER/WASHER OPERATION

SYSTEM
2. Front washer switch ON.
3. The front washer switch provides ground for the front washer motor.
5. BCM transmits the front wiper request signal (LO) to IPDM E/R using CAN communication.
7. The front wiper operates.
NOTE:
BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 3 times after
front washer switch OFF is detected.
Fail-Safe INFOID:0000000012782943
FAIL−SAFE OPERATION
IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
PCS-19, "Fail-safe" (with Intelligent Key system) or PCS-47, "Fail-Safe" (without Intelligent Key system).

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000013380038
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Direct Diagnostic Mode Description
ECU Identification The BCM part number is displayed.
D
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components. E
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM. F
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
G
BCM can perform the following functions.
Direct Diagnostic Mode

H
CAN DIAG SUPPORT MNTR

Self Diagnostic Result
I
System Sub System
ECU Identification
Configuration
Work support
Data Monitor
J
Active Test
K
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × WW
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
M
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
Air conditioner AIR CONDITIONER × N
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
BCM BCM × × × × × O
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
P
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×

WIPER
WIPER : CONSULT Function (BCM - WIPER) INFOID:0000000013380046
DATA MONITOR
Monitor Item [Unit] Description

PUSH SW [On/Off] Indicates condition of push-button ignition switch.
VEH SPEED 1 [km/h] Indicates vehicle speed signal received from ABS on CAN communication line.
FR WIPER HI [On/Off]
FR WIPER LOW [On/Off]
Indicates condition of wiper operation of combination switch.
FR WASHER SW [On/Off]
FR WIPER INT [On/Off]
Indicates front wiper auto stop signal received from IPDM E/R on CAN communication
FR WIPER STOP [On/Off]
line.
INT VOLUME [1 − 7] Indicates condition of intermittent wiper operation of combination switch.
ACTIVE TEST
Test Item Description

FR WIPER This test is able to check front wiper operation [INT/Lo/Hi/Off].
WORK SUPPORT
Support Item Setting Description

On Front wiper intermittent time linked with vehicle speed and wiper dial position.
WIPER SPEED SETTING
Off* Front wiper intermittent time linked with wiper dial position.
* : Initial setting

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000013380052
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
ECU Identification The BCM part number is displayed.
D
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components. E
Work support The settings for BCM functions can be changed.
• The vehicle specification can be read and saved.
Configuration
• The vehicle specification can be written when replacing BCM. F
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
SYSTEM APPLICATION
G
BCM can perform the following functions.
Direct Diagnostic Mode

H

Self Diagnostic Result
I
System Sub System
ECU Identification
Configuration
Work support
Data Monitor
J
Active Test
K
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × WW
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
M
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × N
Air conditioner AIR CONDITIONER ×
Combination switch COMB SW ×
BCM BCM × × × × × O
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
P
Trunk open TRUNK ×
RAP system RETAINED PWR × ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×

WIPER
WIPER : CONSULT Function (BCM - WIPER) INFOID:0000000013380057
DATA MONITOR

IGN ON SW [On/Off] Indicates condition of ignition switch ON position.
IGN SW CAN [On/Off] Indicates ignition switch ON signal received from IPDM E/R on CAN communication line.
FR WIPER HI [On/Off]
FR WIPER LOW [On/Off]
Indicates condition of wiper operation of combination switch.
FR WIPER INT [On/Off]
FR WASHER SW [On/Off]
INT VOLUME [1 − 7] Indicates condition of intermittent wiper operation of combination switch.
Indicates front wiper auto stop signal received from IPDM E/R on CAN communication
FR WIPER STOP [On/Off]
line.
REVERSE SW CAN [On/Off] Indicates reverse switch signal received from TCM on CAN communication line.
Indicates vehicle speed signal received from combination meter on CAN communication
VEHICLE SPEED [km/h/mph]
line.
ACTIVE TEST
Test Item Description

FR WIPER This test is able to check front wiper operation [INT/Lo/Hi/Off].
WORK SUPPORT
Support Item Setting Description

On Front wiper intermittent time linked with vehicle speed and wiper dial position.
WIPER SPEED SETTING
Off* Front wiper intermittent time linked with wiper dial position.
* : Initial setting

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
A
Diagnosis Description INFOID:0000000013380062
AUTO ACTIVE TEST B

Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Front wiper (LO, HI) C
• Parking lamp
• License plate lamp
• Tail lamp D
• Front fog lamp (if equipped)
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan E
Operation Procedure
NOTE:
Never perform auto active test in the following conditions. F
• Passenger door is open
• CONSULT is connected
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper G
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand. H
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF. I
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5. After a series of the following operations is repeated 3 times, auto active test is completed. J
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-109, K
"Component Inspection".
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times. WW
Operation se-
Inspection location Operation
quence
M
1 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
2 10 seconds N
• Tail lamp
3 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
O
4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds

Concept of Auto Active Test
AWMIA1509GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test
Symptom Inspection contents Possible cause

Any of the following components do not operate YES BCM signal input circuit
• Parking lamp
• License plate lamp Perform auto active test. • Lamp or motor
• Tail lamp Does the applicable system op- • Lamp or motor ground circuit
• Front fog lamp (if equipped) erate? NO • Harness or connector between
• Headlamp (HI, LO) IPDM E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R
• BCM signal input circuit

• CAN communication signal be-
YES tween BCM and ECM
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
ate? • Magnet clutch
• Harness or connector between
NO
IPDM E/R and magnet clutch
• IPDM E/R
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
NO
IPDM E/R and cooling fan motor
• IPDM E/R
CONSULT Function (IPDM E/R) INFOID:0000000013380063
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.

ECU Identification The IPDM E/R part number is displayed.
Self Diagnostic Result The IPDM E/R self diagnostic results are displayed.
Data Monitor The IPDM E/R input/output data is displayed in real time.

A
Active Test The IPDM E/R activates outputs to test components.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
ECU IDENTIFICATION B
The IPDM E/R part number is displayed.
SELF DIAGNOSTIC RESULT
Refer to PCS-20, "DTC Index". C
DATA MONITOR
D
Main
Signals
Indicates cooling fan speed signal received from ECM on CAN communication
MOTOR FAN REQ [%] × E
line
Indicates A/C compressor request signal received from ECM on CAN commu-
AC COMP REQ [On/Off] ×
nication line
F
Indicates position light request signal received from BCM on CAN communica-
TAIL&CLR REQ [On/Off] ×
tion line
Indicates low beam request signal received from BCM on CAN communication
HL LO REQ [On/Off] × G
line
Indicates high beam request signal received from BCM on CAN communication
HL HI REQ [On/Off] ×
line
H
Indicates front fog light request signal received from BCM on CAN communica-
FR FOG REQ [On/Off] ×
tion line
Indicates front wiper request signal received from BCM on CAN communication
FR WIP REQ [Stop/1LOW/Low/Hi] × I
line
WIP AUTO STOP [STOP P/ACT P] × Indicates condition of front wiper auto stop signal
WIP PROT [Off/BLOCK] × Indicates condition of front wiper fail-safe operation
J
Indicates ignition switch ON signal received from BCM on CAN communication
IGN RLY1 -REQ [On/Off]
line
IGN RLY [On/Off] × Indicates condition of ignition relay
K
PUSH SW [On/Off] Indicates condition of push-button ignition switch
INTER/NP SW [On/Off] Indicates condition of CVT shift position
Indicates starter relay status signal received from BCM on CAN communication WW
ST RLY CONT [On/Off]
line
Indicates starter control relay signal received from BCM on CAN communication
IHBT RLY -REQ [On/Off]
line M
ST/INHI RLY [Off/ ST /INHI] Indicates condition of starter relay and starter control relay
DETENT SW [On/Off] Indicates condition of CVT shift selector (park position switch)
N
Indicates daytime running light request signal received from BCM on CAN com-
DTRL REQ [Off]
munication line
Indicates theft warning horn request signal received from BCM on CAN commu-
THFT HRN REQ [On/Off] O
nication line
HORN CHIRP [On/Off] Indicates horn reminder signal received from BCM on CAN communication line
ACTIVE TEST P
Test item Description

HORN This test is able to check horn operation [On].
REAR DEFOGGER This test is able to check rear window defogger operation [On/Off].
FRONT WIPER This test is able to check wiper motor operation [Hi/Lo/Off].

MOTOR FAN This test is able to check cooling fan operation [4/3/2/1].
EXTERNAL LAMPS This test is able to check external lamp operation [Fog/Hi/Lo/TAIL/Off].

Refer to LAN-14, "CAN Diagnostic Support Monitor".

DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYS-
A
TEM)
Diagnosis Description INFOID:0000000013380070
B
AUTO ACTIVE TEST
Description C
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp D
• Tail lamp
• Headlamp (LO, HI) E
• A/C compressor (magnet clutch) (if equipped)
• Cooling fan
Operation Procedure F
NOTE:
Never perform auto active test in the following conditions.
• Passenger door is open
G
• CONSULT is connected
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE: H
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the I
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts. J
5. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF. K
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-248,
"Component Inspection".
Inspection in Auto Active Test WW
When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation se- M
Inspection location Operation
quence
1 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp N
2 10 seconds
• Tail lamp
O
3 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
4 A/C compressor (magnet clutch) (if equipped) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds P

Concept of Auto Active Test
AWMIA1511GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test
Symptom Inspection contents Possible cause

Any of the following components do not operate YES BCM signal input circuit
• Parking lamp
• License plate lamp Perform auto active test. • Lamp or motor
• Tail lamp Does the applicable system op- • Lamp or motor ground circuit
• Front fog lamp (if equipped) erate? NO • Harness or connector between
• Headlamp (HI, LO) IPDM E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R
• BCM signal input circuit

• CAN communication signal be-
YES tween BCM and ECM
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
ate? • Magnet clutch
NO
IPDM E/R and magnet clutch
• IPDM E/R
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
NO
IPDM E/R and cooling fan motor
• IPDM E/R
CONSULT Function (IPDM E/R) INFOID:0000000013380073
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.

ECU Identification The IPDM E/R part number is displayed.
Self Diagnostic Result The IPDM E/R self diagnostic results are displayed.
Data Monitor The IPDM E/R input/output data is displayed in real time.

A
Active Test The IPDM E/R activates outputs to test components.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
ECU IDENTIFICATION B
The IPDM E/R part number is displayed.
SELF DIAGNOSTIC RESULT
Refer to PCS-48, "DTC Index". C
DATA MONITOR
D
Main
Signals
Indicates cooling fan speed signal received from ECM on CAN communication
MOTOR FAN REQ [%] × E
line
Indicates A/C compressor request signal received from ECM on CAN commu-
AC COMP REQ [On/Off] ×
nication line
F
Indicates position light request signal received from BCM on CAN communica-
TAIL&CLR REQ [On/Off] ×
tion line
Indicates low beam request signal received from BCM on CAN communication
HL LO REQ [On/Off] × G
line
Indicates high beam request signal received from BCM on CAN communication
HL HI REQ [On/Off] ×
line
H
Indicates front fog light request signal received from BCM on CAN communica-
FR FOG REQ [On/Off] ×
tion line
Indicates front wiper request signal received from BCM on CAN communication
FR WIP REQ [Stop/1LOW/Low/Hi] × I
line
WIP AUTO STOP [STOP P/ACT P] × Indicates condition of front wiper auto stop signal
WIP PROT [Off/BLOCK] × Indicates condition of front wiper fail-safe operation
J
Indicates ignition switch ON signal received from BCM on CAN communication
IGN RLY1 -REQ [On/Off]
line
IGN RLY [On/Off] × Indicates condition of ignition relay
K
INTER/NP SW [On/Off] Indicates condition of CVT shift position
Indicates starter relay status signal received from BCM on CAN communication
ST RLY CONT [On/Off]
line WW
Indicates starter control relay signal received from BCM on CAN communication
IHBT RLY -REQ [On/Off]
line
ST/INHI RLY [Off/ ST /INHI] Indicates condition of starter relay and starter control relay M
DETENT SW [On/Off] Indicates condition of CVT shift selector (park position switch)
Indicates daytime running light request signal received from BCM on CAN com-
DTRL REQ [Off]
munication line N
Indicates theft warning horn request signal received from BCM on CAN commu-
THFT HRN REQ [On/Off]
nication line
HORN CHIRP [On/Off] Indicates horn reminder signal received from BCM on CAN communication line O
ACTIVE TEST
P
HORN This test is able to check horn operation [On].
REAR DEFOGGER This test is able to check rear window defogger operation [On/Off].
FRONT WIPER This test is able to check wiper motor operation [Hi/Lo/Off].
MOTOR FAN This test is able to check cooling fan operation [4/3/2/1].
EXTERNAL LAMPS This test is able to check external lamp operation [Fog/Hi/Lo/TAIL/Off].

Refer to LAN-14, "CAN Diagnostic Support Monitor".

BCM, IPDM E/R
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
BCM, IPDM E/R
List of ECU Reference INFOID:0000000012782952
B
WITH INTELLIGENT KEY SYSTEM
ECU Reference C
BCS-30, "Reference Value"
BCS-48, "Fail-safe"
BCM D
BCS-49, "DTC Inspection Priority Chart"
BCS-50, "DTC Index"
PCS-13, "Reference Value" E
IPDM E/R PCS-19, "Fail-safe"
PCS-20, "DTC Index"
F
WITHOUT INTELLIGENT KEY SYSTEM
ECU Reference G
BCS-103, "Reference Value"
BCS-114, "Fail-safe" H
BCM
BCS-115, "DTC Inspection Priority Chart"
BCS-115, "DTC Index"
PCS-42, "Reference Value" I
IPDM E/R PCS-47, "Fail-Safe"
PCS-48, "DTC Index"
J
WW

WIPER AND WASHER SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM
Wiring Diagram - With Intelligent Key INFOID:0000000013380087
ABLWA3377GB

< WIRING DIAGRAM >
WW
ABLIA8393GB

< WIRING DIAGRAM >
ABLIA8394GB

< WIRING DIAGRAM >
WW
ABLIA8395GB

< WIRING DIAGRAM >
ABLIA8396GB

< WIRING DIAGRAM >
WW
ABLIA8455GB

< WIRING DIAGRAM >
Wiring Diagram - Without Intelligent Key INFOID:0000000013380088
ABLWA3378GB

< WIRING DIAGRAM >
WW
ABLIA8397GB

< WIRING DIAGRAM >
ABLIA8398GB

< WIRING DIAGRAM >
WW
ABLIA5835GB

< WIRING DIAGRAM >
ABLIA8456GB

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000012782955
B
OVERALL SEQUENCE
C
WW
P
ALKIA1982GB
DETAILED FLOW
1. OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.

< BASIC INSPECTION >
>> GO TO 2.
2. CONFIRM THE SYMPTOM
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3. IDENTIFY THE MALFUNCTIONING SYSTEM WITH SYMPTOM DIAGNOSIS
Use Symptom diagnosis from the symptom inspection result in step 2 and then identify where to start perform-
ing the diagnosis based on possible causes and symptoms. Refer to WW-47, "Symptom Table".
>> GO TO 4.
4. PERFORM THE COMPONENT DIAGNOSIS OF THE OF THE APPLICABLE SYSTEM
Perform the diagnosis with Component diagnosis of the applicable system.
>> GO TO 5.
5. REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6. FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES >> Inspection End.
NO >> GO TO 3.

WIPER AND WASHER FUSE
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS A
WIPER AND WASHER FUSE
Description INFOID:0000000012782956
B
Fuse list
Unit Location Fuse No. Capacity
C
Front wiper motor IPDM E/R 35 30 A
Front washer motor Fuse block (J/B) 6 10 A
D
Diagnosis Procedure INFOID:0000000012782957
1. CHECK FUSES
E
Check that the following fuses are not blown.

F
Front wiper motor IPDM E/R 35 30 A
Front washer motor Fuse block (J/B) 6 10 A
Is the fuse blown? G
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> Inspection End.
H
WW

FRONT WIPER MOTOR LO CIRCUIT
Component Function Check INFOID:0000000012782958
1. CHECK FRONT WIPER LO OPERATION

IPDM E/R AUTO ACTIVE TEST
1. Start IPDM E/R auto active test. Refer to PCS-9, "Diagnosis Description" (with Intelligent Key system) or
PCS-38, "Diagnosis Description" (without Intelligent Key system).
2. Check that the front wiper operates at the LO operation.
CONSULT ACTIVE TEST
1. Select FRONT WIPER of IPDM E/R active test item.
2. While operating the test item, check that front wiper LO operation and OFF.
Lo : Front wiper LO operation

Off : Stop the front wiper.
Is the inspection result normal?
YES >> Front wiper motor LO circuit is normal.
NO >> Refer to WW-38, "Diagnosis Procedure".
Regarding Wiring Diagram information, refer to WW-24, "Wiring Diagram - With Intelligent Key" or WW-30,
"Wiring Diagram - Without Intelligent Key".
1. CHECK FRONT WIPER MOTOR (LO) INPUT VOLTAGE

CONSULT ACTIVE TEST
2. Disconnect front wiper motor.
3. Turn the ignition switch ON.
5. While operating the test item, check voltage between IPDM E/R harness connector E45 and ground.
Terminals
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER
Connector Terminal
Ground
Lo Battery voltage
E45 35
Off 0V
YES >> GO TO 2.
NO >> Replace IPDM E/R. Refer to PCS-31, "Removal and Installation" (with Intelligent Key system) or
PCS-60, "Removal and Installation" (without Intelligent Key system).
2. CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
2. Disconnect IPDM E/R.
3. Check continuity between IPDM E/R harness connector E45 and front wiper motor harness connector E1.
IPDM E/R Front wiper motor

Continuity
Connector Terminal Connector Terminal
E45 35 E1 1 Yes

YES >> GO TO 3.
NO >> Repair or replace the harness or connectors. A
3. CHECK FRONT WIPER MOTOR (LO) SHORT CIRCUIT
Check continuity between IPDM E/R harness connector E45 and ground.
B
IPDM E/R
Continuity
Connector Terminal Ground
C
E45 35 No
YES >> Repair or replace the harness or connectors. D
NO >> Replace front wiper motor. Refer to WW-64, "Removal and Installation".
WW

FRONT WIPER MOTOR HI CIRCUIT
1. CHECK FRONT WIPER HI OPERATION

1. Start IPDM E/R auto active test. Refer to WW-15, "Diagnosis Description" (with Intelligent Key system) or
WW-19, "Diagnosis Description" (without Intelligent Key system).
2. Check that the front wiper operates at the HI operation.
CONSULT ACTIVE TEST
2. While operating the test item, check that front wiper HI operation and OFF.
Hi : Front wiper HI operation

YES >> The front wiper motor HI circuit is normal.
1. CHECK FRONT WIPER MOTOR (HI) INPUT VOLTAGE

CONSULT ACTIVE TEST
5. While operating the test item, check voltage between IPDM E/R harness connector E45 and ground.
Terminals
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER
Connector Terminal
Ground
Hi Battery voltage
E45 29
Off 0V
YES >> GO TO 2.
NO >> Replace IPDM E/R. Refer to PCS-31, "Removal and Installation" (with Intelligent Key system) or
2. CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
2. Disconnect IPDM E/R.

Continuity
E45 29 E1 4 Yes

YES >> GO TO 3.
NO >> Repair or replace the harness or connectors. A
3. CHECK FRONT WIPER MOTOR (HI) SHORT CIRCUIT
Check continuity between IPDM E/R harness connector E45 and ground.
B
IPDM E/R
Continuity
C
E45 29 No
YES >> Repair or replace the harness or connectors. D
NO >> Replace front wiper motor. Refer to WW-64, "Removal and Installation".
WW

FRONT WIPER AUTO STOP SIGNAL CIRCUIT
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
1. CHECK FRONT WIPER (AUTO STOP) OPERATION

CONSULT DATA MONITOR
1. Select “WIP AUTO STOP” of IPDM E/R DATA MONITOR item.
2. Operate the front wiper.
3. With the front wiper operation, check the monitor status.
Monitor item Condition Monitor status

Stop position STOP P
WIP AUTO STOP Front wiper motor
Except ACT P
YES >> Auto stop signal circuit is normal.
1. CHECK IPDM E/R OUTPUT VOLTAGE

4. Check voltage between front wiper motor connector E1 and ground.
Front wiper motor Voltage

Connector Terminal Ground (Approx.)
E1 5 Battery voltage
YES >> Replace front wiper motor. Refer to WW-64, "Removal and Installation".
NO >> GO TO 2.
2. CHECK FRONT WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
2. Disconnect IPDM E/R connector.

Continuity
E46 39 E1 5 Yes
4. Check continuity between IPDM E/R harness connector E46 and ground.
IPDM E/R
Continuity
E46 39 No
YES >> Replace IPDM E/R. Refer to PCS-31, "Removal and Installation" (with Intelligent Key system) or
NO >> Repair or replace the harness or connectors.
FRONT WIPER MOTOR GROUND CIRCUIT
FRONT WIPER MOTOR GROUND CIRCUIT
A
B
C
1.CHECK FRONT WIPER MOTOR (GND) OPEN CIRCUIT

1. Turn the ignition switch OFF. D
3. Check continuity between front wiper motor harness connector E1 and ground.
E
Front wiper motor
Continuity
E1 2 Yes F
YES >> Front wiper motor ground circuit is normal.
NO >> Repair or replace the harness or connectors. G
WW

WASHER MOTOR CIRCUIT
1. CHECK FRONT WASHER MOTOR FUSE

2. Check that the following fuse is not blown.

Front washer motor Fuse block (J/B) 6 10A
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2. CHECK FRONT WASHER MOTOR POWER SUPPLY
1. Disconnect front washer motor.
2. Turn ignition switch ON.
3. Check voltage between front washer motor harness connector E8 and ground.
Front washer motor Voltage

Connector Terminal (Approx.)
Ground
E8 1 Battery voltage
YES >> GO TO 3.
3. CHECK FRONT WASHER MOTOR CIRCUIT CONTINUITY
2. Disconnect combination switch (wiper and washer switch).
3. Check continuity between combination switch (wiper and washer switch) harness connector M28 and
front washer motor E8.
Combination switch (wiper and washer switch) Front washer motor

Continuity
M28 1 E8 2 Yes
YES >> GO TO 4.
4. CHECK WIPER AND WASHER SWITCH GROUND CIRCUIT
Check continuity between combination switch (wiper and washer switch) harness connector M28 and ground.
Combination switch (wiper and washer switch)

Continuity
M28 6 Yes
YES >> GO TO 5.

5. CHECK WIPER AND WASHER SWITCH A
Check wiper and washer switch. Refer to WW-46, "Component Inspection".
YES >> Replace front washer motor. Refer to WW-54, "Removal and Installation". B
NO >> Replace wiper and washer switch. Refer to WW-65, "Removal and Installation".
WW

WASHER SWITCH
WASHER SWITCH
• Washer switch is integrated with combination switch (wiper and washer switch).
• Combination switch (wiper and washer switch) supplies ground and fuse # 6 supplies power for the front
washer motor to operate.
AWLIA2070GB
Component Inspection INFOID:0000000012782967
1. CHECK WASHER SWITCH

2. Disconnect combination switch (wiper and washer switch) connector M28.
3. Check continuity between the combination switch (wiper and washer switch) terminals.
A: Terminal 1
B: Terminal 6
ALLIA0546GB
Combination switch (wiper and washer switch)

Condition Continuity
Terminal
1 6 Washer switch ON Yes
YES >> Washer switch is normal.
NO >> Replace combination switch (wiper and washer switch). Refer to WW-65, "Removal and Installa-
tion".

WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
Symptom Table INFOID:0000000012782968
B
CAUTION:
Perform the self-diagnosis with CONSULT before performing the diagnosis by symptom. Perform the
diagnosis by DTC if DTC is detected. C
Symptom Probable malfunction location Inspection item

Combination switch (wiper D
and washer switch)
• Combination switch (wiper and washer switch)
Refer to BCS-76, "Symptom
• Harness between combination switch (wiper
Table" (with Intelligent Key
and washer switch) and BCM E
system) or BCS-133, "Symp-
• BCM
tom Table" (without Intelli-
gent Key system).
HI only
• IPDM E/R Front wiper motor (HI) circuit F
• Harness between IPDM E/R and front wiper Refer to WW-40, "Compo-
motor nent Function Check".
• Front wiper motor
G
Front wiper request signal
IPDM E/R
• BCM
Data monitor “FR WIP REQ”
• IPDM E/R
H
Combination switch (wiper
and washer switch)
Table" (with Intelligent Key I
and washer switch) and BCM
• BCM
Front wiper does not
gent Key system).
operate
LO and INT
• IPDM E/R
J
Front wiper motor (LO) circuit
• Harness between IPDM E/R and front wiper
Refer to WW-38, "Compo-
motor
nent Function Check".
• Front wiper motor K
IPDM E/R
• BCM
• IPDM E/R
WW
and washer switch)
Table" (with Intelligent Key M
INT only • BCM
gent Key system).
N
IPDM E/R
• BCM
• IPDM E/R
SYMPTOM DIAGNOSIS O
HI, LO, and INT
Refer to WW-50, "Diagnosis Procedure".

and washer switch)
• BCM
HI only
gent Key system).
IPDM E/R
• BCM
• IPDM E/R
IPDM E/R —
and washer switch)
• BCM
Front wiper does not system) or BCS-133, "Symp-
stop tom Table" (without Intelli-
LO only
gent Key system).
IPDM E/R
• BCM
• IPDM E/R
IPDM E/R —
and washer switch)
• BCM
INT only tom Table" (without Intelli-
gent Key system).
IPDM E/R
• BCM
• IPDM E/R
and washer switch)
Intermittent adjustment Table" (with Intelligent Key
cannot be performed. system) or BCS-133, "Symp-
• BCM
gent Key system).
BCM —
Check the vehicle speed detection wiper setting.
Intermittent control
Refer to WW-12, "WIPER : CONSULT Function (BCM - WIPER)" (with Intelligent
linked with vehicle
Key
speed cannot be per-
system) or WW-14, "WIPER : CONSULT Function (BCM - WIPER)" (without Intel-
formed.
ligent Key system).
Front wiper does not
operate normally Combination switch (wiper
and washer switch)
Wiper is not linked to Table" (with Intelligent Key
the washer operation. system) or BCS-133, "Symp-
• BCM
gent Key system).
BCM —
Does not return to stop
position (Repeatedly • IPDM E/R Front wiper auto stop signal
operates for 10 sec- • Harness between IPDM E/R and front wiper circuit
onds and then stops for motor Refer to: WW-42, "Compo-
20 seconds. After that, • Front wiper motor nent Function Check".
it stops the operation.

A
and washer switch)
Table" (with Intelligent Key B
Front washer motor and washer switch) and BCM
Front washer motor system) or BCS-133, "Symp-
does not operate when • BCM
does not operate. tom Table" (without Intelli-
washing the windshield. gent Key system).
• Harness between combination switch (wiper Front washer motor circuit
C
and washer switch) and front washer motor Refer to WW-44, "Diagnosis
• Front washer motor Procedure".
D
WW

FRONT WIPER DOES NOT OPERATE
The front wiper does not operate under any operation conditions
1. CHECK WIPER RELAY OPERATION

1. Start IPDM E/R auto active test. Refer to WW-15, "Diagnosis Description" (with Intelligent Key system) or
WW-19, "Diagnosis Description" (without Intelligent Key system).
2. Check that the front wiper operates at the LO/HI operation.
CONSULT ACTIVE TEST
2. While operating the test item, check that front wiper LO/HI operation and OFF.
Lo : Front wiper LO operation

Hi : Front wiper HI operation
is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 2.
2. CHECK FRONT WIPER MOTOR FUSE
2. Check that the front wiper motor fuse 30A (No. 35, located in the IPDM E/R) is not blown.
Is the fuse blown?
YES >> Replace the fuse after repairing the affected circuit.
NO >> GO TO 3.
3. CHECK FRONT WIPER MOTOR (GND) OPEN CIRCUIT
2. Check continuity between front wiper motor harness connector E1 and ground.
Front wiper motor

Continuity
E1 2 Yes
YES >> GO TO 4.
4. CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
CONSULT ACTIVE TEST
3. With operating the test item, check voltage between IPDM E/R harness connector E45 and ground.

Terminals A
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER B
Connector Terminal
Ground Lo Battery voltage

35
Off 0V C
E45
Hi Battery voltage
29
Off 0V
Is the inspection result normal? D
YES LO circuit>>Refer to WW-38, "Diagnosis Procedure".
YES HI circuit>>Refer to WW-40, "Diagnosis Procedure".
NO >> Replace IPDM E/R. Refer to PCS-31, "Removal and Installation" (with Intelligent Key system) or E
5. CHECK FRONT WIPER REQUEST SIGNAL INPUT
F
CONSULT DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R DATA MONITOR item.
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the monitor status. G
Monitor item With operating the front wiper switch condition Monitor status
ON Hi
H
Front wiper switch HI
OFF Stop
FR WIP REQ
ON Low
Front wiper switch LO I
OFF Stop
YES >> Replace IPDM E/R. Refer to PCS-31, "Removal and Installation" (with Intelligent Key system) or J
NO >> GO TO 6.
6. CHECK COMBINATION SWITCH (WIPER AND WASHER SWITCH) K
1. Perform the inspection of the combination switch (wiper and washer switch). Refer to BCS-76, "Symptom
Table" (with Intelligent Key system) or BCS-133, "Symptom Table" (without Intelligent Key system).
WW
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation" (with Intelligent Key system) or BCS-
135, "Removal and Installation" (without Intelligent Key system).
NO >> Repair or replace the malfunctioning parts. M

NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
FRONT WIPER MOTOR PROTECTION FUNCTION

• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.

WASHER TANK
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
WASHER TANK
Exploded View INFOID:0000000012782972
B
AWLIA2590ZZ
H
1. Washer tank inlet 2. Washer tank 3. Washer level switch
4. Washer tank seal 5. Washer pump
I
Removal and Installation INFOID:0000000012782973
REMOVAL J
1. Remove the washer tank inlet.
2. Remove the fender protector (RH). Refer to EXT-28, "FENDER PROTECTOR : Removal and Installation -
Front Fender Protector". K
3. Disconnect the harness connectors from the washer pump and washer level switch.
4. Disconnect the washer tube from the washer pump.
5. Remove the washer tank bolts and the washer tank. WW
6. Remove the washer pump, washer level switch, and washer tank seals from the washer tank (if neces-
sary).
M
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist. N
• Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications".

WASHER PUMP
WASHER PUMP
The washer pump is serviced as an assembly with the washer tank. Refer to WW-53, "Removal and Installa-
tion".

WASHER LEVEL SWITCH
WASHER LEVEL SWITCH
A
The washer level switch is serviced as an assembly with the washer tank. Refer to WW-53, "Removal and B
Installation".
WW

WASHER NOZZLE & TUBE
AWLIA2589ZZ
1. Check valve 2. Washer tube 3. Washer tank

4. Washer pump 5. Washer nozzle Clip
WASHER NOZZLE
WASHER NOZZLE : Removal and Installation INFOID:0000000012782977
REMOVAL
1. Disconnect the washer nozzle from the hood by pushing on the
nozzle in the order and direction shown.
JMLIA2359ZZ
2. Disconnect the washer tube from the washer nozzle.

3. Remove the washer nozzle.
INSTALLATION

CAUTION: A
Adjust the nozzle spray pattern. Refer to WW-57, "WASHER NOZZLE : Adjustment".
WASHER NOZZLE : Adjustment INFOID:0000000012782978
B
AWLIA2035ZZ
K
1. Washer fluid spray pattern 2. Washer nozzle (RH) 3. Washer nozzle (LH)
4. Black print 5. Windshield glass A. 487.0 mm (19.2 in)
WW
B. 22.2 mm (0.9 in) C. 15.3 mm (0.6 in) D. 145.9 mm (5.7 in)
E. 384.9 mm (15.2 in) F. 15.0 mm (0.6 in) G. 499.7 mm (19.7 in)
H. 470.2 mm (18.5 in)
M
NOTE:
Spray position for (LH) shown. (RH) is symmetrical.
N
Insert a suitable tool into the nozzle hole (A) and move up/down and
left/right to adjust the spray position of each nozzle (1).
O
AWLIA2036ZZ
WASHER TUBE

WASHER TUBE : Removal and Installation INFOID:0000000012782979
REMOVAL
1. Remove the fender protector (RH). Refer to EXT-28, "FENDER PROTECTOR : Removal and Installation -
Front Fender Protector".
2. Remove the hood insulator.
3. Remove the washer tube retainers.
4. Remove the washer spray pattern.
5. Disconnect the washer tube from the washer nozzles (LH/RH). Refer to WW-56, "WASHER NOZZLE :
Removal and Installation".
6. Disconnect the washer tube from the washer pump.
7. Remove the washer tube from the clips and remove the washer tube.
INSTALLATION
NOTE:
Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications".

FRONT WIPER ARM
FRONT WIPER ARM
A
G
AWLIA2038ZZ
1. Wiper blade (RH) 2. Wiper arm (RH) 3. Wiper drive assembly

4. Wiper arm (LH) 5. Wiper blade (LH)
H
I
REMOVAL
1. Remove the wiper arm cap.
2. Remove the wiper arm nut. J
3. Raise the wiper arm, then remove the wiper arm.
INSTALLATION K
1. Clean the wiper arm mount as shown.
NOTE:
This will reduce the possibility of wiper arm looseness. WW
N
ELH0717D
2. Install the wiper arm. O

3. Install the wiper arm nut.
4. Install the wiper arm cap.
5. Check that the wiper blades stop at the park position. P

WIPER BLADE
WIPER BLADE
WIPER BLADE
WIPER BLADE : Removal and Installation INFOID:0000000012782982
REMOVAL
1. Put the wiper arms in the service position.
a. Turn the ignition switch ON and then OFF.
b. Within 1 minute, activate washer switch 2 times in less than 0.5 seconds to put the wiper arms in the ser-
vice position.
2. Lift the wiper arm away from the windshield glass.
3. Rotate the wiper blade and push the release tab (A), then move
the wiper blade down (B) the wiper arm.
4. Remove the wiper blade.
AWLIA1565ZZ
INSTALLATION
CAUTION:
Return the wiper arm to the service position on the windshield to prevent damage when the hood is
opened.
1. Insert the wiper blade onto the wiper arm and slide it up until it clicks into place.
2. Rotate the wiper blade so the dimple is in the groove.
3. Lay the wiper arm back down in the service position on the windshield.
4. Turn the ignition ON and operate the windshield wipers to ensure the repair has been completed properly.
Operating the windshield wipers will cancel service mode.
5. Check that the wiper blade contacts the windshield properly; otherwise the wiper arm may be damaged
from wind pressure while driving.
WIPER BLADE REFILL
WIPER BLADE REFILL : Removal and Installation INFOID:0000000012782983
REMOVAL
1. Remove the wiper blade. Refer to WW-60, "WIPER BLADE : Removal and Installation".

WIPER BLADE
2. Hold the wiper blade refill lip at the end (A) of the wiper blade (1)
with a suitable tool (B) as shown and pull it firmly in the direction A
(C).
(D): U clip (part of wiper blade)
B
G
ALLIA0860ZZ
• If the wiper blade refill lip is torn due to wear, insert a suitable H
tool (A) into the space between the end of the wiper blade refill
(1) and the wiper blade (2) and pull the wiper blade refill (1) out
as shown.
I
ALLIA0861ZZ
K
INSTALLATION
1. If the rib (A) has become detached from the wiper blade refill (1),
check that the curve of the rib (A) is in the same direction as the WW
curve of the wiper blade refill (1) and insert the rib (A) into the slit
(B) in the wiper blade refill (1) as shown.
M
ALLIA0866ZZ
O

WIPER BLADE
• If the rib (A) has a notch (B), insert the rib (A) into the wiper
blade refill (1) so the notch (B) fits over the protrusion (C) in
the wiper blade refill (1) as shown.
ALLIA0867ZZ
2. Insert the wiper blade refill (1) tip into the end of the wiper blade
(2) in the direction (C). Push the wiper blade refill (1) in while
pressing it into the end of the wiper blade (2) as shown. After the
wiper blade refill is fully inserted, remove the holder (B).
(A): Tab (part of wiper blade) (2)
ALLIA0862ZZ
• Make sure to slide the refill into the wiper blade so that the
wiper blade refill is held by the tabs (A) on the wiper blade as
shown.
ALLIA0863ZZ

WIPER BLADE
3. Push the wiper blade refill (1) until the tabs on the wiper blade
(2) fit into the stoppers (A) in the end of the wiper blade refill (1). A
Make sure the LOCK mark (B) on the wiper blade refill (1) is
aligned with the lock point symbol (C) on the wiper blade (2) as
shown.
B
G
ALLIA0864ZZ
4. Before installing the wiper blade, make sure that the wiper blade
refill (1) end is fully covered by the wiper blade (2) in area (A) as H
shown.
ALLIA0865ZZ
K
5. Install the wiper blade. Refer to WW-60, "WIPER BLADE : Removal and Installation".
WW

FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
AWLIA2038ZZ
1. Wiper blade (RH) 2. Wiper arm (RH) 3. Wiper drive assembly

4. Wiper arm (LH) 5. Wiper blade (LH)
REMOVAL
1. Remove the cowl top. Refer to EXT-26, "Removal and Installation".
2. Disconnect the harness connector from the wiper drive assembly.
3. Remove the wiper drive assembly bolts.
4. Remove the wiper drive assembly.
INSTALLATION
1. Install the wiper drive assembly.
2. Install the wiper drive assembly bolts.
3. Connect the harness connector to the wiper drive assembly.
4. Install the cowl top. Refer to EXT-26, "Removal and Installation".
5. Check the operation of the wiper blades and that they stop at the normal position.

WIPER AND WASHER SWITCH
WIPER AND WASHER SWITCH
A
B
The wiper and washer switch is serviced as an assembly with the combination switch. Refer to EXL-137,
"Removal and Installation".
C
WW

SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
Specifications INFOID:0000000012782987
WINDSHIELD WASHER FLUID
Windshield washer fluid capacity 4.8 (5 1/8 US qt, 4 1/4 Imp qt)
Windshield washer fluid specification Refer to MA-12, "Fluids and Lubricants".

Wiper & Washer: Section

Uploaded by

Copyright:

Available Formats

Wiper & Washer: Section

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wiper & Washer: Section

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

Revision: December 2015 WW-1 2016 Sentra NAM

REMOVAL AND INSTALLATION ............... 53 WIPER AND WASHER SWITCH ...................... 65

Revision: December 2015 WW-2 2016 Sentra NAM

Precaution for Work INFOID:0000000012782937

Revision: December 2015 WW-4 2016 Sentra NAM

Revision: December 2015 WW-5 2016 Sentra NAM

FRONT WIPER AND WASHER SYSTEM

Revision: December 2015 WW-6 2016 Sentra NAM

Revision: December 2015 WW-7 2016 Sentra NAM

System Description INFOID:0000000012782942

FRONT WIPER CONTROL (BASIC)

Revision: December 2015 WW-8 2016 Sentra NAM

AUTO STOP OPERATION

Revision: December 2015 WW-9 2016 Sentra NAM

Revision: December 2015 WW-10 2016 Sentra NAM

Direct Diagnostic Mode

CAN DIAG SUPPORT MNTR

Revision: December 2015 WW-11 2016 Sentra NAM

Monitor Item [Unit] Description

Test Item Description

Support Item Setting Description

Revision: December 2015 WW-12 2016 Sentra NAM

Direct Diagnostic Mode

CAN DIAG SUPPORT MNTR

Revision: December 2015 WW-13 2016 Sentra NAM

Monitor Item [Unit] Description

Test Item Description

Support Item Setting Description

Revision: December 2015 WW-14 2016 Sentra NAM

AUTO ACTIVE TEST B

Revision: December 2015 WW-15 2016 Sentra NAM

Symptom Inspection contents Possible cause

• BCM signal input circuit

CONSULT Function (IPDM E/R) INFOID:0000000013380063

Direct Diagnostic Mode Description

Revision: December 2015 WW-16 2016 Sentra NAM

Test item Description

Revision: December 2015 WW-17 2016 Sentra NAM

CAN DIAG SUPPORT MNTR

Revision: December 2015 WW-18 2016 Sentra NAM

Revision: December 2015 WW-19 2016 Sentra NAM

Symptom Inspection contents Possible cause

• BCM signal input circuit

CONSULT Function (IPDM E/R) INFOID:0000000013380073

Direct Diagnostic Mode Description

Revision: December 2015 WW-20 2016 Sentra NAM

Revision: December 2015 WW-21 2016 Sentra NAM

Revision: December 2015 WW-22 2016 Sentra NAM

Revision: December 2015 WW-23 2016 Sentra NAM

Revision: December 2015 WW-24 2016 Sentra NAM

Revision: December 2015 WW-25 2016 Sentra NAM

Revision: December 2015 WW-26 2016 Sentra NAM

Revision: December 2015 WW-27 2016 Sentra NAM

Revision: December 2015 WW-28 2016 Sentra NAM

Revision: December 2015 WW-29 2016 Sentra NAM

Revision: December 2015 WW-30 2016 Sentra NAM

Revision: December 2015 WW-31 2016 Sentra NAM

Revision: December 2015 WW-32 2016 Sentra NAM